W25Q64BV
Publication Release Date: July 08, 2010
- 1 - Revision E
64M-BIT
SERIAL FLASH MEMORY WITH
DUAL AND QUAD SPI
W25Q64BV
- 2 -
Table of Contents
1. GENERAL DESCRIPTION ............................................................................................................... 5
2. FEATURES....................................................................................................................................... 5
3. PIN CONFIGURATION SOIC 208-MIL ............................................................................................ 6
4. PAD CONFIGURATION WSON 8X6-MM ........................................................................................ 6
5. PAD CONFIGURATION PDIP 300-MIL ........................................................................................... 7
6. PIN DESCRIPTION SOIC 208-MIL, PDIP 300-MIL AND WSON 8X6-MM...................................... 7
7. PIN CONFIGURATION SOIC 300-MIL ............................................................................................ 8
8. PIN DESCRIPTION SOIC 300-MIL .................................................................................................. 8
8.1 Package Types..................................................................................................................... 9
8.2 Chip Select (/CS).................................................................................................................. 9
8.3 Serial Data Input, Output and IOs (DI, DO and IO0, IO1, IO2, IO3) .................................... 9
8.4 Write Protect (/WP)............................................................................................................... 9
8.5 HOLD (/HOLD) ..................................................................................................................... 9
8.6 Serial Clock (CLK)................................................................................................................ 9
9. BLOCK DIAGRAM.......................................................................................................................... 10
10. FUNCTIONAL DESCRIPTION ....................................................................................................... 11
10.1 SPI OPERATIONS ............................................................................................................. 11
10.1.1 Standard SPI Instructions...................................................................................................11
10.1.2 Dual SPI Instructions ..........................................................................................................11
10.1.3 Quad SPI Instructions.........................................................................................................11
10.1.4 Hold Function .....................................................................................................................11
10.2 WRITE PROTECTION ....................................................................................................... 12
10.2.1 Write Protect Features........................................................................................................12
11. CONTROL AND STATUS REGISTERS ........................................................................................ 13
11.1 STATUS REGISTER .......................................................................................................... 13
11.1.1 BUSY..................................................................................................................................13
11.1.2 Write Enable Latch (WEL) ..................................................................................................13
11.1.3 Block Protect Bits (BP2, BP1, BP0)....................................................................................13
11.1.4 Top/Bottom Block Protect (TB)...........................................................................................13
11.1.5 Sector/Block Protect (SEC) ................................................................................................13
11.1.6 Status Register Protect (SRP1, SRP0)...............................................................................14
11.1.7 Quad Enable (QE) ..............................................................................................................14
11.1.8 Status Register Memory Protection ....................................................................................16
11.2 INSTRUCTIONS................................................................................................................. 17
11.2.1 Manufacturer and Device Identification ..............................................................................17
11.2.2 Instruction Set Table 1........................................................................................................18
W25Q64BV
11.2.3 Instruction Set Table 2 (Read Instructions) ........................................................................19
Publication Release Date: July 08, 2010
- 3 - Revision E
11.2.4 Write Enable (06h)..............................................................................................................20
11.2.5 Write Disable (04h).............................................................................................................20
11.2.6 Read Status Register-1 (05h) and Read Status Register-2 (35h).......................................21
11.2.7 Write Status Register (01h) ................................................................................................22
11.2.8 Read Data (03h) .................................................................................................................23
11.2.9 Fast Read (0Bh) .................................................................................................................24
11.2.10 Fast Read Dual Output (3Bh) ...........................................................................................25
11.2.11 Fast Read Quad Output (6Bh)..........................................................................................26
11.2.12 Fast Read Dual I/O (BBh).................................................................................................27
11.2.13 Fast Read Quad I/O (EBh) ...............................................................................................29
11.2.14 Octal Word Read Quad I/O (E3h).....................................................................................31
11.2.15 Page Program (02h) .........................................................................................................33
11.2.16 Quad Input Page Program (32h) ......................................................................................34
11.2.17 Sector Erase (20h) ...........................................................................................................35
11.2.18 32KB Block Erase (52h) ...................................................................................................36
11.2.19 64KB Block Erase (D8h)...................................................................................................37
11.2.20 Chip Erase (C7h / 60h).....................................................................................................38
11.2.21 Erase Suspend (75h)........................................................................................................39
11.2.22 Erase Resume (7Ah) ........................................................................................................40
11.2.23 Power-down (B9h)............................................................................................................41
11.2.24 High Performance Mode (A3h) .........................................................................................42
11.2.25 Release Power-down or High Performance Mode / Device ID (ABh) ...............................42
11.2.26 Read Manufacturer / Device ID (90h) ...............................................................................44
11.2.27 Read Unique ID Number (4Bh).........................................................................................45
11.2.28 Read JEDEC ID (9Fh) ......................................................................................................46
11.2.29 Continuous Read Mode Reset (FFh or FFFFh)................................................................47
12. ELECTRICAL CHARACTERISTICS .............................................................................................. 48
12.1 Absolute Maximum Ratings................................................................................................ 48
12.2 Operating Ranges .............................................................................................................. 48
12.3 Power-up Timing and Write Inhibit Threshold .................................................................... 49
12.4 DC Electrical Characteristics.............................................................................................. 50
12.5 AC Measurement Conditions ............................................................................................. 51
12.6 AC Electrical Characteristics .............................................................................................. 52
12.7 AC Electrical Characteristics (cont’d)................................................................................. 53
12.8 Serial Output Timing........................................................................................................... 54
12.9 Input Timing........................................................................................................................ 54
12.10 Hold Timing ....................................................................................................................... 54
13. PACKAGE SPECIFICATION.......................................................................................................... 55
W25Q64BV
13.1 8-Pin SOIC 208-mil (Package Code SS) ........................................................................... 55
- 4 -
13.2 8-Pin PDIP 300-mil (Package Code DA)............................................................................ 56
13.3 8-Contact 8x6mm WSON (Package Code ZE) .................................................................. 57
13.4 16-Pin SOIC 300-mil (Package Code SF).......................................................................... 58
14. ORDERING INFORMATION .......................................................................................................... 59
14.1 Valid Part Numbers and Top Side Marking........................................................................ 60
15. REVISION HISTORY...................................................................................................................... 61
W25Q64BV
Publication Release Date: July 08, 2010
- 5 - Revision E
1. GENERAL DESCRIPTION
The W25Q64BV (64M-bit) Serial Flash memory provides a storage solution for systems with limited
space, pins and power. The 25Q series offers flexibility and performance well beyond ordinary Serial
Flash devices. They are ideal for code shadowing to RAM, executing code directly from Dual/Quad SPI
(XIP) and storing voice, text and data. The devices operate on a single 2.7V to 3.6V power supply with
current consumption as low as 4mA active and 1µA for power-down. All devices are offered in space-
saving packages.
The W25Q64BV array is organized into 32,768 programmable pages of 256-bytes each. Up to 256 bytes
can be programmed at a time. Pages can be erased in groups of 16 (sector erase), groups of 128 (32KB
block erase), groups of 256 (64KB block erase) or the entire chip (chip erase). The W25Q64BV has 2,048
erasable sectors and 128 erasable blocks respectively. The small 4KB sectors allow for greater flexibility
in applications that require data and parameter storage. (See figure 2.)
The W25Q64BV supports the standard Serial Peripheral Interface (SPI), and a high performance
Dual/Quad output as well as Dual/Quad I/O SPI: Serial Clock, Chip Select, Serial Data I/O0 (DI), I/O1
(DO), I/O2 (/WP), and I/O3 (/HOLD). SPI clock frequencies of up to 80MHz are supported allowing
equivalent clock rates of 160MHz for Dual Output and 320MHz for Quad Output when using the Fast
Read Dual/Quad Output instructions. These transfer rates can outperform standard Asynchronous 8 and
16-bit Parallel Flash memories. The Continuous Read Mode allows for efficient memory access with as
few as 8-clocks of instruction-overhead to read a 24-bit address, allowing true XIP (execute in place)
operation.
A Hold pin, Write Protect pin and programmable write protection, with top or bottom array control,
provide further control flexibility. Additionally, the device supports JEDEC standard manufacturer and
device identification with a 64-bit Unique Serial Number.
2. FEATURES
Family of SpiFlash Memories
W25Q64BV: 64M-bit / 8M-byte (8,388,608)
– 256-bytes per programmable page
Standard, Dual or Quad SPI
– Standard SPI: CLK, /CS, DI, DO, /WP, /Hold
– Dual SPI: CLK, /CS, IO0, IO1, /WP, /Hold
– Quad SPI: CLK, /CS, IO0, IO1, IO2, IO3
Highest Performance Serial Flash
– Up to 6X that of ordinary Serial Flash
– 80MHz clock operation
– 160MHz equivalent Dual SPI
– 320MHz equivalent Quad SPI
– 40MB/S continuous data transfer rate
Efficient “Continuous Read Mode”
– Low Instruction overhead
– As few as 8 clocks to address memory
– Allows true XIP (execute in place) operation
– Outperforms X16 Parallel Flash
Note 1: Contact Winbond for details
Low Power, Wide Temperature Range
– Single 2.7 to 3.6V supply
– 4mA active current, <1µA Power-down (typ.)
– -40°C to +85°C operating range
Flexible Architecture with 4KB sectors
– Uniform Sector Erase (4K-bytes)
– Block Erase (32K and 64K-bytes)
– Program one to 256 bytes
More than 100,000 erase/write cycles
More than 20-year data retention
Advanced Security Features
– Software and Hardware Write-Protect
– Top or Bottom, Sector or Block selection
– Lock-Down and OTP protection(1)
– 64-Bit Unique ID for each device(1)
Space Efficient Packaging
– 8-pin SOIC 208-mil
– 8-pin PDIP 300-mil
– 8-pad WSON 8x6-mm
– 16-pin SOIC 300-mil
– Contact Winbond for KGD and other options
W25Q64BV
- 6 -
3. PIN CONFIGURATION SOIC 208-MIL
1
2
3
4
8
7
6
5
/CS
DO (IO
1
)
/WP (IO
2
)
GND
VCC
/HOLD (IO
3
)
CLK
DI (IO
0
)
1
2
3
4
8
7
6
5
/CS
DO (IO
1
)
/WP (IO
2
)
GND
VCC
/HOLD (IO
3
)
CLK
DI (IO
0
)
Figure 1a. W25Q64BV Pin Assignments, 8-pin SOIC 208-mil (Package Code SS)
4. PAD CONFIGURATION WSON 8X6-MM
1
2
3
4
8
7
6
5
/CS
DO (IO
1
)
/WP (IO
2
)
GND
VCC
/HOLD (IO
3
)
CLK
DI (IO
0
)
1
2
3
4
8
7
6
5
/CS
DO (IO
1
)
/WP (IO
2
)
GND
VCC
/HOLD (IO
3
)
CLK
DI (IO
0
)
Figure 1b. W25Q64BV Pad Assignments, 8-pad WSON 8x6-mm(Package Code ZE)
W25Q64BV
Publication Release Date: July 08, 2010
- 7 - Revision E
5. PAD CONFIGURATION PDIP 300-MIL
1
2
3
4
8
7
6
5
/CS
DO (IO
1
)
/WP (IO
2
)
GND
VCC
/HOLD (IO
3
)
CLK
DI (IO
0
)
1
2
3
4
8
7
6
5
/CS
DO (IO
1
)
/WP (IO
2
)
GND
VCC
/HOLD (IO
3
)
CLK
DI (IO
0
)
Figure 1c. W25Q64BV Pin Assignments, 8-pin PDIP (Package Code DA)
6. PIN DESCRIPTION SOIC 208-MIL, PDIP 300-MIL AND WSON 8X6-MM
PIN NO. PIN NAME I/O FUNCTION
1 /CS I Chip Select Input
2 DO (IO1) I/O Data Output (Data Input Output 1)*1
3 /WP (IO2) I/O Write Protect Input ( Data Input Output 2)*2
4 GND Ground
5 DI (IO0) I/O Data Input (Data Input Output 0)*1
6 CLK I Serial Clock Input
7 /HOLD (IO3) I/O Hold Input (Data Input Output 3)*2
8 VCC Power Supply
*1 IO0 and IO1 are used for Standard and Dual SPI instructions
*2 IO0 – IO3 are used for Quad SPI instructions
W25Q64BV
- 8 -
7. PIN CONFIGURATION SOIC 300-MIL
1/HOLD (IO
3
)
2
3
4
5
6
7
8
16
15
14
13
12
11
10
9
VCC
N/C
N/C
N/C
N/C
/CS
DO (IO )
CLK
DI (IO
0
)
N/C
N/C
N/C
N/C
GND
/WP (IO )
1 2
1/HOLD (IO
3
)
2
3
4
5
6
7
8
16
15
14
13
12
11
10
9
VCC
N/C
N/C
N/C
N/C
/CS
DO (IO )
CLK
DI (IO
0
)
N/C
N/C
N/C
N/C
GND
/WP (IO )
1 2
Figure 1d. W25Q64BV Pin Assignments, 16-pin SOIC 300-mil (Package Code SF)
8. PIN DESCRIPTION SOIC 300-MIL
PAD NO. PAD NAME I/O FUNCTION
1 /HOLD (IO3) I/O Hold Input (Data Input Output 3)*2
2 VCC Power Supply
3 N/C No Connect
4 N/C No Connect
5 N/C No Connect
6 N/C No Connect
7 /CS I Chip Select Input
8 DO (IO1) I/O Data Output (Data Input Output 1)*1
9 /WP (IO2) I/O Write Protect Input (Data Input Output 2)*2
10 GND Ground
11 N/C No Connect
12 N/C No Connect
13 N/C No Connect
14 N/C No Connect
15 DI (IO0) I/O Data Input (Data Input Output 0)*1
16 CLK I Serial Clock Input
*1 IO0 and IO1 are used for Standard and Dual SPI instructions
*2 IO0 – IO3 are used for Quad SPI instructions
W25Q64BV
Publication Release Date: July 08, 2010
- 9 - Revision E
8.1 Package Types
W25Q64BV is offered in an 8-pin plastic 208-mil width SOIC (package code SS) and 8x6-mm WSON
(package code ZE) as shown in figure 1a, and 1b, respectively. The 300-mil 8-pin PDIP is another option
of package selections (Figure 1c). The W25Q64BV is also offered in a 16-pin plastic 300-mil width SOIC
(package code SF) as shown in figure 1d. Package diagrams and dimensions are illustrated at the end of
this datasheet.
8.2 Chip Select (/CS)
The SPI Chip Select (/CS) pin enables and disables device operation. When /CS is high the device is
deselected and the Serial Data Output (DO, or IO0, IO1, IO2, IO3) pins are at high impedance. When
deselected, the devices power consumption will be at standby levels unless an internal erase, program or
status register cycle is in progress. When /CS is brought low the device will be selected, power
consumption will increase to active levels and instructions can be written to and data read from the
device. After power-up, /CS must transition from high to low before a new instruction will be accepted.
The /CS input must track the VCC supply level at power-up (see “Write Protection” and figure 31). If
needed a pull-up resister on /CS can be used to accomplish this.
8.3 Serial Data Input, Output and IOs (DI, DO and IO0, IO1, IO2, IO3)
The W25Q64BV supports standard SPI, Dual SPI and Quad SPI operation. Standard SPI instructions use
the unidirectional DI (input) pin to serially write instructions, addresses or data to the device on the rising
edge of the Serial Clock (CLK) input pin. Standard SPI also uses the unidirectional DO (output) to read
data or status from the device on the falling edge CLK.
Dual and Quad SPI instruction use the bidirectional IO pins to serially write instructions, addresses or
data to the device on the rising edge of CLK and read data or status from the device on the falling edge of
CLK. Quad SPI instructions require the non-volatile Quad Enable bit (QE) in Status Register-2 to be set.
When QE=1 the /WP pin becomes IO2 and /HOLD pin becomes IO3.
8.4 Write Protect (/WP)
The Write Protect (/WP) pin can be used to prevent the Status Register from being written. Used in
conjunction with the Status Register’s Block Protect (SEC, TB, BP2, BP1 and BP0) bits and Status
Register Protect (SRP) bits, a portion or the entire memory array can be hardware protected. The /WP
pin is active low. When the QE bit of Status Register-2 is set for Quad I/O, the /WP pin (Hardware Write
Protect) function is not available since this pin is used for IO2. See figure 1a, 1b, 1c and 1d for the pin
configuration of Quad I/O operation.
8.5 HOLD (/HOLD)
The /HOLD pin allows the device to be paused while it is actively selected. When /HOLD is brought low,
while /CS is low, the DO pin will be at high impedance and signals on the DI and CLK pins will be ignored
(don’t care). When /HOLD is brought high, device operation can resume. The /HOLD function can be
useful when multiple devices are sharing the same SPI signals. The /HOLD pin is active low. When the
QE bit of Status Register-2 is set for Quad I/O, the /HOLD pin function is not available since this pin is
used for IO3. See figure 1a-d for the pin configuration of Quad I/O operation.
8.6 Serial Clock (CLK)
The SPI Serial Clock Input (CLK) pin provides the timing for serial input and output operations. ("See SPI
Operations")
W25Q64BV
- 10 -
9. BLOCK DIAGRAM
Figure 2. W25Q64BV Serial Flash Memory Block Diagram
00FF00h 00FFFFh
Block 0 (64KB) •
000000h 0000FFh
1FFF00h 1FFFFFh
Block 31 (64KB) •
1F0000h 1F00FFh
20FF00h 20FFFFh
Block 32 (64KB) •
200000h 2000FFh
3FFF00h 3FFFFFh
Block 63 (64KB) •
3F0000h 3F00FFh
40FF00h 40FFFFh
Block 64 (64KB) •
400000h 4000FFh
7FFF00h 7FFFFFh
Block 127 (64KB) •
7F0000h 7F00FFh
Column Decode
And 256-Byte Page Buffer
Beginning
Page Address
Ending
Page Address
W25Q64BV
SPI
Command &
Control Logic
Byte Address
Latch / Counter
Status
Register
Write Control
Logic
Page Address
Latch / Counter
High Voltage
Generators
xx0F00h xx0FFFh
Sector 0 (4KB) •
xx0000h xx00FFh
xx1F00h xx1FFFh
Sector 1 (4KB) •
xx1000h xx10FFh
xx2F00h xx2FFFh
Sector 2 (4KB) •
xx2000h xx20FFh
xxDF00h xxDFFFh
Sector 13 (4KB) •
xxD000h xxD0FFh
xxEF00h xxEFFFh
Sector 14 (4KB) •
xxE000h xxE0FFh
xxFF00h xxFFFFh
Sector 15 (4KB) •
xxF000h xxF0FFh
Block Segmentation
Data
Write Protect Logic and Row Decode
DO (IO1)
DI (IO0)
/CS
CLK
/HOLD (IO3)
/WP (IO2)
00FF00h 00FFFFh
Block 0 (64KB) •
000000h 0000FFh
1FFF00h 1FFFFFh
Block 31 (64KB) •
1F0000h 1F00FFh
20FF00h 20FFFFh
Block 32 (64KB) •
200000h 2000FFh
3FFF00h 3FFFFFh
Block 63 (64KB) •
3F0000h 3F00FFh
40FF00h 40FFFFh
Block 64 (64KB) •
400000h 4000FFh
7FFF00h 7FFFFFh
Block 127 (64KB) •
7F0000h 7F00FFh
Column Decode
And 256-Byte Page Buffer
Beginning
Page Address
Ending
Page Address
W25Q64BV
SPI
Command &
Control Logic
Byte Address
Latch / Counter
Status
Register
Write Control
Logic
Page Address
Latch / Counter
High Voltage
Generators
xx0F00h xx0FFFh
Sector 0 (4KB) •
xx0000h xx00FFh
xx1F00h xx1FFFh
Sector 1 (4KB) •
xx1000h xx10FFh
xx2F00h xx2FFFh
Sector 2 (4KB) •
xx2000h xx20FFh
xxDF00h xxDFFFh
Sector 13 (4KB) •
xxD000h xxD0FFh
xxEF00h xxEFFFh
Sector 14 (4KB) •
xxE000h xxE0FFh
xxFF00h xxFFFFh
Sector 15 (4KB) •
xxF000h xxF0FFh
Block Segmentation
Data
Write Protect Logic and Row Decode
DO (IO1)
DI (IO0)
/CS
CLK
/HOLD (IO3)
/WP (IO2)
W25Q64BV
Publication Release Date: July 08, 2010
- 11 - Revision E
10. FUNCTIONAL DESCRIPTION
10.1 SPI OPERATIONS
10.1.1 Standard SPI Instructions
The W25Q64BV is accessed through an SPI compatible bus consisting of four signals: Serial Clock
(CLK), Chip Select (/CS), Serial Data Input (DI) and Serial Data Output (DO). Standard SPI instructions
use the DI input pin to serially write instructions, addresses or data to the device on the rising edge of
CLK. The DO output pin is used to read data or status from the device on the falling edge CLK.
SPI bus operation Modes 0 (0,0) and 3 (1,1) are supported. The primary difference between Mode 0 and
Mode 3 concerns the normal state of the CLK signal when the SPI bus master is in standby and data is
not being transferred to the Serial Flash. For Mode 0 the CLK signal is normally low on the falling and
rising edges of /CS. For Mode 3 the CLK signal is normally high on the falling and rising edges of /CS.
10.1.2 Dual SPI Instructions
The W25Q64BV supports Dual SPI operation when using the “Fast Read Dual Output and Dual I/O” (3B
and BB hex) instructions. These instructions allow data to be transferred to or from the device at two to
three times the rate of ordinary Serial Flash devices. The Dual Read instructions are ideal for quickly
downloading code to RAM upon power-up (code-shadowing) or for executing non-speed-critical code
directly from the SPI bus (XIP). When using Dual SPI instructions the DI and DO pins become
bidirectional I/O pins: IO0 and IO1.
10.1.3 Quad SPI Instructions
The W25Q64BV supports Quad SPI operation when using the “Fast Read Quad Output”, “Fast Read
Quad I/O” and “Octal Word Read Quad I/O” (6B, EB and E3 hex respectively). These instructions allow
data to be transferred to or from the device four to six times the rate of ordinary Serial Flash. The Quad
Read instructions offer a significant improvement in continuous and random access transfer rates
allowing fast code-shadowing to RAM or execution directly from the SPI bus (XIP). When using Quad SPI
instructions the DI and DO pins become bidirectional IO0 and IO1, and the /WP and /HOLD pins become
IO2 and IO3 respectively. Quad SPI instructions require the non-volatile Quad Enable bit (QE) in Status
Register-2 to be set.
10.1.4 Hold Function
The /HOLD signal allows the W25Q64BV operation to be paused while it is actively selected (when /CS is
low). The /HOLD function may be useful in cases where the SPI data and clock signals are shared with
other devices. For example, consider if the page buffer was only partially written when a priority interrupt
requires use of the SPI bus. In this case the /HOLD function can save the state of the instruction and the
data in the buffer so programming can resume where it left off once the bus is available again. The
/HOLD function is only available for standard SPI and Dual SPI operation, not during Quad SPI.
To initiate a /HOLD condition, the device must be selected with /CS low. A /HOLD condition will activate
on the falling edge of the /HOLD signal if the CLK signal is already low. If the CLK is not already low the
/HOLD condition will activate after the next falling edge of CLK. The /HOLD condition will terminate on the
rising edge of the /HOLD signal if the CLK signal is already low. If the CLK is not already low the /HOLD
condition will terminate after the next falling edge of CLK. During a /HOLD condition, the Serial Data
Output (DO) is high impedance, and Serial Data Input (DI) and Serial Clock (CLK) are ignored. The Chip
Select (/CS) signal should be kept active (low) for the full duration of the /HOLD operation to avoid
resetting the internal logic state of the device.
W25Q64BV
- 12 -
10.2 WRITE PROTECTION
Applications that use non-volatile memory must take into consideration the possibility of noise and other
adverse system conditions that may compromise data integrity. To address this concern the W25Q64BV
provides several means to protect data from inadvertent writes.
10.2.1 Write Protect Features
Device resets when VCC is below threshold
Time delay write disable after Power-up
Write enable/disable instructions and automatic write disable after program and erase
Software and Hardware (/WP pin) write protection using Status Register
Write Protection using Power-down instruction
Lock Down write protection until next power-up(1)
One Time Program (OTP) write protection(1)
Note 1: These features are available upon special order. Please contact Winbond for details.
Upon power-up or at power-down, the W25Q64BV will maintain a reset condition while VCC is below the
threshold value of VWI, (See Power-up Timing and Voltage Levels and Figure 31). While reset, all
operations are disabled and no instructions are recognized. During power-up and after the VCC voltage
exceeds VWI, all program and erase related instructions are further disabled for a time delay of tPUW. This
includes the Write Enable, Page Program, Sector Erase, Block Erase, Chip Erase and the Write Status
Register instructions. Note that the chip select pin (/CS) must track the VCC supply level at power-up until
the VCC-min level and tVSL time delay is reached. If needed a pull-up resister on /CS can be used to
accomplish this.
After power-up the device is automatically placed in a write-disabled state with the Status Register Write
Enable Latch (WEL) set to a 0. A Write Enable instruction must be issued before a Page Program, Sector
Erase, Chip Erase or Write Status Register instruction will be accepted. After completing a program,
erase or write instruction the Write Enable Latch (WEL) is automatically cleared to a write-disabled state
of 0.
Software controlled write protection is facilitated using the Write Status Register instruction and setting
the Status Register Protect (SRP0, SRP1) and Block Protect (SEC,TB, BP2, BP1 and BP0) bits. These
settings allow a portion or all of the memory to be configured as read only. Used in conjunction with the
Write Protect (/WP) pin, changes to the Status Register can be enabled or disabled under hardware
control. See Status Register for further information. Additionally, the Power-down instruction offers an
extra level of write protection as all instructions are ignored except for the Release Power-down
instruction.
W25Q64BV
Publication Release Date: July 08, 2010
- 13 - Revision E
11. CONTROL AND STATUS REGISTERS
The Read Status Register-1 and Status Register-2 instructions can be used to provide status on the
availability of the Flash memory array, if the device is write enabled or disabled, the state of write
protection and the Quad SPI setting. The Write Status Register instruction can be used to configure the
devices write protection features and Quad SPI setting. Write access to the Status Register is controlled by
the state of the non-volatile Status Register Protect bits (SRP0, SRP1), the Write Enable instruction, and
in some cases the /WP pin.
11.1 STATUS REGISTER
11.1.1 BUSY
BUSY is a read only bit in the status register (S0) that is set to a 1 state when the device is executing a
Page Program, Sector Erase, Block Erase, Chip Erase or Write Status Register instruction. During this
time the device will ignore further instructions except for the Read Status Register and Erase Suspend
instruction (see tW, tPP, tSE, tBE, and tCE in AC Characteristics). When the program, erase or write status
register instruction has completed, the BUSY bit will be cleared to a 0 state indicating the device is ready
for further instructions.
11.1.2 Write Enable Latch (WEL)
Write Enable Latch (WEL) is a read only bit in the status register (S1) that is set to a 1 after executing a
Write Enable Instruction. The WEL status bit is cleared to a 0 when the device is write disabled. A write
disable state occurs upon power-up or after any of the following instructions: Write Disable, Page
Program, Sector Erase, Block Erase, Chip Erase and Write Status Register.
11.1.3 Block Protect Bits (BP2, BP1, BP0)
The Block Protect Bits (BP2, BP1, BP0) are non-volatile read/write bits in the status register (S4, S3, and
S2) that provide Write Protection control and status. Block Protect bits can be set using the Write Status
Register Instruction (see tW in AC characteristics). All, none or a portion of the memory array can be
protected from Program and Erase instructions (see Status Register Memory Protection table). The
factory default setting for the Block Protection Bits is 0, none of the array protected.
11.1.4 Top/Bottom Block Protect (TB)
The non-volatile Top/Bottom bit (TB) controls if the Block Protect Bits (BP2, BP1, BP0) protect from the
Top (TB=0) or the Bottom (TB=1) of the array as shown in the Status Register Memory Protection table.
The factory default setting is TB=0. The TB bit can be set with the Write Status Register Instruction
depending on the state of the SRP0, SRP1 and WEL bits.
11.1.5 Sector/Block Protect (SEC)
The non-volatile Sector protect bit (SEC) controls if the Block Protect Bits (BP2, BP1, BP0) protect 4KB
Sectors (SEC=1) or 64KB Blocks (SEC=0) in the Top (TB=0) or the Bottom (TB=1) of the array as shown
in the Status Register Memory Protection table. The default setting is SEC=0.
W25Q64BV
- 14 -
11.1.6 Status Register Protect (SRP1, SRP0)
The Status Register Protect bits (SRP1 and SRP0) are non-volatile read/write bits in the status register
(S8 and S7). The SRP bits control the method of write protection: software protection, hardware
protection, power supply lock-down or one time programmable (OTP) protection.
SRP1 SRP0 /WP Status
Register Description
0 0 X Software
Protection
/WP pin has no control. The Status register can be written to
after a Write Enable instruction, WEL=1. [Factory Default]
0 1 0
Hardware
Protected
When /WP pin is low the Status Register locked and can not
be written to.
0 1 1
Hardware
Unprotected
When /WP pin is high the Status register is unlocked and can
be written to after a Write Enable instruction, WEL=1.
1 0 X
Power Supply
Lock-Down(1)
Status Register is protected and can not be written to again
until the next power-down, power-up cycle.(2)
1 1 X
One Time
Program(1)
Status Register is permanently protected and can not be
written to.
Note:
1. These features are available upon special order. Please contact Winbond for details.
2. When SRP1, SRP0 = (1, 0), a power-down, power-up cycle will change SRP1, SRP0 to (0, 0) state.
11.1.7 Quad Enable (QE)
The Quad Enable (QE) bit is a non-volatile read/write bit in the status register (S9) that allows Quad
operation. When the QE bit is set to a 0 state (factory default) the /WP pin and /Hold are enabled. When
the QE bit is set to a 1 the Quad IO2 and IO3 pins are enabled.
WARNING: The QE bit should never be set to a 1 during standard SPI or Dual SPI operation if the
/WP or /HOLD pins are tied directly to the power supply or ground.
W25Q64BV
Publication Release Date: July 08, 2010
- 15 - Revision E
Figure 3a. Status Register-1
Figure 3b. Status Register-2
W25Q64BV
- 16 -
1
1.1.8 Status Register Memory Protection
STATUS REGISTER(1) W25Q64BV (64M-BIT) MEMORY PROTECTION
SEC TB BP2 BP1 BP0 BLOCK(S) ADDRESSES DENSITY PORTION
X X 0 0 0 NONE NONE NONE NONE
0 0 0 0 1 126 & 127 7E0000h – 7FFFFFh 128KB Upper 1/64
0 0 0 1 0 124 ~ 127 7C0000h – 7FFFFFh 256KB Upper 1/32
0 0 0 1 1 120 ~ 127 780000h – 7FFFFFh 512KB Upper 1/16
0 0 1 0 0 112 ~ 127 700000h – 7FFFFFh 1MB Upper 1/8
0 0 1 0 1 96 ~ 127 600000h – 7FFFFFh 2MB Upper 1/4
0 0 1 1 0 64 ~ 127 400000h – 7FFFFFh 4MB Upper 1/2
0 1 0 0 1 0 & 1 000000h – 01FFFFh 128KB Lower 1/64
0 1 0 1 0 0 ~ 3 000000h – 03FFFFh 256KB Lower 1/32
0 1 0 1 1 0 ~ 7 000000h – 07FFFFh 512KB Lower 1/16
0 1 1 0 0 0 ~ 15 000000h – 0FFFFFh 1MB Lower 1/8
0 1 1 0 1 0 ~ 31 000000h – 1FFFFFh 2MB Lower 1/4
0 1 1 1 0 0 ~ 63 000000h – 3FFFFFh 4MB Lower 1/2
X X 1 1 1 0 ~ 127 000000h – 7FFFFFh 8MB ALL
1 0 0 0 1 127 7FF000h – 7FFFFFh 4KB Top Block
1 0 0 1 0 127 7FE000h – 7FFFFFh 8KB Top Block
1 0 0 1 1 127 7FC000h – 7FFFFFh 16KB Top Block
1 0 1 0 X 127 7F8000h – 7FFFFFh 32KB Top Block
1 1 0 0 1 0 000000h – 000FFFh 4KB Bottom Block
1 1 0 1 0 0 000000h – 001FFFh 8KB Bottom Block
1 1 0 1 1 0 000000h – 003FFFh 16KB Bottom Block
1 1 1 0 X 0 000000h – 007FFFh 32KB Bottom Block
Note:
1. x = don’t care
W25Q64BV
Publication Release Date: July 08, 2010
- 17 - Revision E
11.2 INSTRUCTIONS
The instruction set of the W25Q64BV consists of twenty seven basic instructions that are fully controlled
through the SPI bus (see Instruction Set table). Instructions are initiated with the falling edge of Chip
Select (/CS). The first byte of data clocked into the DI input provides the instruction code. Data on the DI
input is sampled on the rising edge of clock with most significant bit (MSB) first.
Instructions vary in length from a single byte to several bytes and may be followed by address bytes, data
bytes, dummy bytes (don’t care), and in some cases, a combination. Instructions are completed with the
rising edge of edge /CS. Clock relative timing diagrams for each instruction are included in figures 4
through 30. All read instructions can be completed after any clocked bit. However, all instructions that
Write, Program or Erase must complete on a byte boundary (/CS driven high after a full 8-bits have been
clocked) otherwise the instruction will be terminated. This feature further protects the device from
inadvertent writes. Additionally, while the memory is being programmed or erased, or when the Status
Register is being written, all instructions except for Read Status Register will be ignored until the program
or erase cycle has completed.
11.2.1 Manufacturer and Device Identification
MANUFACTURER ID (M7-M0)
Winbond Serial Flash EFh
Device ID (ID7-ID0) (ID15-ID0)
Instruction ABh, 90h 9Fh
W25Q64BV 16h 4017h
W25Q64BV
- 18 -
11.2.2 Instruction Set Table 1 (1)
INSTRUCTION
NAME
BYTE 1
(CODE) BYTE 2 BYTE 3 BYTE 4 BYTE 5 BYTE 6
Write Enable 06h
Write Disable 04h
Read Status Register-1 05h (S7–S0) (2)
Read Status Register-2 35h (S15-S8) (2)
Write Status Register 01h (S7–S0) (S15-S8)
Page Program 02h A23–A16 A15–A8 A7–A0 (D7–D0)
Quad Page Program 32h A23–A16 A15–A8 A7–A0 (D7–D0, …)(3)
Block Erase (64KB) D8h A23–A16 A15–A8 A7–A0
Block Erase (32KB) 52h A23–A16 A15–A8 A7–A0
Sector Erase (4KB) 20h A23–A16 A15–A8 A7–A0
Chip Erase C7h/60h
Erase Suspend 75h
Erase Resume 7Ah
Power-down B9h
High Performance Mode A3h dummy dummy dummy
Continuous Read Mode
Reset (4) FFh FFh
Release Power down or
HPM / Device ID ABh dummy dummy dummy (ID7-ID0) (5)
Manufacturer/
Device ID(6) 90h dummy dummy 00h (MF7-MF0) (ID7-ID0)
Read Unique ID(7) 4Bh dummy dummy dummy dummy (ID63-ID0)
JEDEC ID 9Fh (MF7-MF0)
Manufacturer
(ID15-ID8)
Memory Type
(ID7-ID0)
Capacity
Notes:
1. Data bytes are shifted with Most Significant Bit first. Byte fields with data in parenthesis “()” indicate data being read
from the device on the DO pin.
2. The Status Register contents will repeat continuously until /CS terminates the instruction.
3. Quad Page Program Input Data
IO0 = (D4, D0, ……)
IO1 = (D5, D1, ……)
IO2 = (D6, D2, ……)
IO3 = (D7, D3, ……)
4. This instruction is recommended when using the Dual or Quad “Continuous Read Mode” feature. See section
11.2.29 for more information.
5. The Device ID will repeat continuously until /CS terminates the instruction.
6. See Manufacturer and Device Identification table for Device ID information.
7. This feature is available upon special order. Please contact Winbond for details.
W25Q64BV
Publication Release Date: July 08, 2010
- 19 - Revision E
11.2.3 Instruction Set Table 2 (Read Instructions)
INSTRUCTION
NAME
BYTE 1
(CODE) BYTE 2 BYTE 3 BYTE 4 BYTE 5 BYTE 6
Read Data 03h A23-A16 A15-A8 A7-A0 (D7-D0)
Fast Read 0Bh A23-A16 A15-A8 A7-A0 dummy (D7-D0)
Fast Read Dual Output 3Bh A23-A16 A15-A8 A7-A0 dummy (D7-D0, …)(1)
Fast Read Dual I/O BBh A23-A8(2) A7-A0, M7-M0(2) (D7-D0, …)(1)
Fast Read Quad Output 6Bh A23-A16 A15-A8 A7-A0 dummy (D7-D0, …)(3)
Fast Read Quad I/O EBh A23-A0, M7-M0(4) (x,x,x,x, D7-D0, …)(5) (D7-D0, …)(3)
Octal Word Read
Quad I/O(6) E3h A23-A0, M7-M0(4) (D7-D0, …)(3)
Notes:
1. Dual Output data
IO0 = (D6, D4, D2, D0)
IO1 = (D7, D5, D3, D1)
2. Dual Input Address
IO0 = A22, A20, A18, A16, A14, A12, A10, A8 A6, A4, A2, A0, M6, M4, M2, M0
IO1 = A23, A21, A19, A17, A15, A13, A11, A9 A7, A5, A3, A1, M7, M5, M3, M1
3. Quad Output Data
IO0 = (D4, D0, …..)
IO1 = (D5, D1, …..)
IO2 = (D6, D2, …..)
IO3 = (D7, D3, …..)
4. Quad Input Address
IO0 = A20, A16, A12, A8, A4, A0, M4, M0
IO1 = A21, A17, A13, A9, A5, A1, M5, M1
IO2 = A22, A18, A14, A10, A6, A2, M6, M2
IO3 = A23, A19, A15, A11, A7, A3, M7, M3
5. Fast Read Quad I/O Data
IO0 = (x, x, x, x, D4, D0, …..)
IO1 = (x, x, x, x, D5, D1, …..)
IO2 = (x, x, x, x, D6, D2, …..)
IO3 = (x, x, x, x, D7, D3, …..)
6. The lowest 4 address bits must be 0. ( A0, A1, A2, A3 = 0 )
W25Q64BV
- 20 -
11.2.4 Write Enable (06h)
The Write Enable instruction (Figure 4) sets the Write Enable Latch (WEL) bit in the Status Register to a
1. The WEL bit must be set prior to every Page Program, Sector Erase, Block Erase, Chip Erase and
Write Status Register instruction. The Write Enable instruction is entered by driving /CS low, shifting the
instruction code “06h” into the Data Input (DI) pin on the rising edge of CLK, and then driving /CS high.
Figure 4. Write Enable Instruction Sequence Diagram
11.2.5 Write Disable (04h)
The Write Disable instruction (Figure 5) resets the Write Enable Latch (WEL) bit in the Status Register to
a 0. The Write Disable instruction is entered by driving /CS low, shifting the instruction code “04h” into the
DI pin and then driving /CS high. Note that the WEL bit is automatically reset after Power-up and upon
completion of the Write Status Register, Page Program, Sector Erase, Block Erase and Chip Erase
instructions.
Figure 5. Write Disable Instruction Sequence Diagram
W25Q64BV
Publication Release Date: July 08, 2010
- 21 - Revision E
11.2.6 Read Status Register-1 (05h) and Read Status Register-2 (35h)
The Read Status Register instructions allow the 8-bit Status Registers to be read. The instruction is
entered by driving /CS low and shifting the instruction code “05h” for Status Register-1 and “35h” for
Status Register-2 into the DI pin on the rising edge of CLK. The status register bits are then shifted out on
the DO pin at the falling edge of CLK with most significant bit (MSB) first as shown in figure 6. The Status
Register bits are shown in figure 3a and 3b and include the BUSY, WEL, BP2-BP0, TB, SEC, SRP0,
SRP1 and QE bits (see description of the Status Register earlier in this datasheet).
The Read Status Register instruction may be used at any time, even while a Program, Erase or Write
Status Register cycle is in progress. This allows the BUSY status bit to be checked to determine when
the cycle is complete and if the device can accept another instruction. The Status Register can be read
continuously, as shown in Figure 6. The instruction is completed by driving /CS high.
Figure 6. Read Status Register Instruction Sequence Diagram
W25Q64BV
- 22 -
11.2.7 Write Status Register (01h)
The Write Status Register instruction allows the Status Register to be written. A Write Enable instruction
must previously have been executed for the device to accept the Write Status Register Instruction (Status
Register bit WEL must equal 1). Once write enabled, the instruction is entered by driving /CS low,
sending the instruction code “01h”, and then writing the status register data byte as illustrated in figure 7.
The Status Register bits are shown in figure 3 and described earlier in this datasheet.
Only non-volatile Status Register bits SRP0, SEC, TB, BP2, BP1, BP0 (bits 7, 5, 4, 3, 2 of Status
Register-1) and QE, SRP1(bits 9 and 8 of Status Register-2) can be written to. All other Status Register
bit locations are read-only and will not be affected by the Write Status Register instruction.
The /CS pin must be driven high after the eighth or sixteenth bit of data that is clocked in. If this is not
done the Write Status Register instruction will not be executed. If /CS is driven high after the eighth clock
(compatible with the 25X series) the QE and SRP1 bits will be cleared to 0. After /CS is driven high, the
self-timed Write Status Register cycle will commence for a time duration of tW (See AC Characteristics).
While the Write Status Register cycle is in progress, the Read Status Register instruction may still be
accessed to check the status of the BUSY bit. The BUSY bit is a 1 during the Write Status Register cycle
and a 0 when the cycle is finished and ready to accept other instructions again. After the Write Register
cycle has finished the Write Enable Latch (WEL) bit in the Status Register will be cleared to 0.
The Write Status Register instruction allows the Block Protect bits (SEC, TB, BP2, BP1 and BP0) to be
set for protecting all, a portion, or none of the memory from erase and program instructions. Protected
areas become read-only (see Status Register Memory Protection table and description). The Write Status
Register instruction also allows the Status Register Protect bits (SRP0, SRP1) to be set. Those bits are
used in conjunction with the Write Protect (/WP) pin, Lock out or OTP features to disable writes to the
status register. Please refer to 11.1.6 for detailed descriptions regarding Status Register protection
methods. Factory default for all status Register bits are 0.
Figure 7. Write Status Register Instruction Sequence Diagram
W25Q64BV
Publication Release Date: July 08, 2010
- 23 - Revision E
11.2.8 Read Data (03h)
The Read Data instruction allows one more data bytes to be sequentially read from the memory. The
instruction is initiated by driving the /CS pin low and then shifting the instruction code “03h” followed by
a 24-bit address (A23-A0) into the DI pin. The code and address bits are latched on the rising edge of the
CLK pin. After the address is received, the data byte of the addressed memory location will be shifted out
on the DO pin at the falling edge of CLK with most significant bit (MSB) first. The address is automatically
incremented to the next higher address after each byte of data is shifted out allowing for a continuous
stream of data. This means that the entire memory can be accessed with a single instruction as long as
the clock continues. The instruction is completed by driving /CS high.
The Read Data instruction sequence is shown in figure 8. If a Read Data instruction is issued while an
Erase, Program or Write cycle is in process (BUSY=1) the instruction is ignored and will not have any
effects on the current cycle. The Read Data instruction allows clock rates from D.C. to a maximum of fR
(see AC Electrical Characteristics).
Figure 8. Read Data Instruction Sequence Diagram
W25Q64BV
- 24 -
11.2.9 Fast Read (0Bh)
The Fast Read instruction is similar to the Read Data instruction except that it can operate at the highest
possible frequency of FR (see AC Electrical Characteristics). This is accomplished by adding eight
“dummy” clocks after the 24-bit address as shown in figure 9. The dummy clocks allow the devices
internal circuits additional time for setting up the initial address. During the dummy clocks the data value
on the DO pin is a “don’t care”.
Figure 9. Fast Read Instruction Sequence Diagram
W25Q64BV
Publication Release Date: July 08, 2010
- 25 - Revision E
11.2.10 Fast Read Dual Output (3Bh)
The Fast Read Dual Output (3Bh) instruction is similar to the standard Fast Read (0Bh) instruction except
that data is output on two pins; IO0 and IO1. This allows data to be transferred from the W25Q64BV at
twice the rate of standard SPI devices. The Fast Read Dual Output instruction is ideal for quickly
downloading code from Flash to RAM upon power-up or for applications that cache code-segments to
RAM for execution.
Similar to the Fast Read instruction, the Fast Read Dual Output instruction can operate at the highest
possible frequency of FR (see AC Electrical Characteristics). This is accomplished by adding eight
“dummy” clocks after the 24-bit address as shown in figure 10. The dummy clocks allow the device's
internal circuits additional time for setting up the initial address. The input data during the dummy clocks
is “don’t care”. However, the IO0 pin should be high-impedance prior to the falling edge of the first data
out clock.
Figure 10. Fast Read Dual Output Instruction Sequence Diagram
W25Q64BV
- 26 -
11.2.11 Fast Read Quad Output (6Bh)
The Fast Read Quad Output (6Bh) instruction is similar to the Fast Read Dual Output (3Bh) instruction
except that data is output on four pins, IO0, IO1, IO2, and IO3. A Quad enable of Status Register-2 must be
executed before the device will accept the Fast Read Quad Output Instruction (Status Register bit QE
must equal 1). The Fast Read Quad Output Instruction allows data to be transferred from the W25Q64BV
at four times the rate of standard SPI devices.
The Fast Read Quad Output instruction can operate at the highest possible frequency of FR (see AC
Electrical Characteristics). This is accomplished by adding eight “dummy” clocks after the 24-bit address
as shown in figure 11. The dummy clocks allow the device's internal circuits additional time for setting up
the initial address. The input data during the dummy clocks is “don’t care”. However, the IO pins should
be high-impedance prior to the falling edge of the first data out clock.
Figure 11. Fast Read Quad Output Instruction Sequence Diagram
W25Q64BV
Publication Release Date: July 08, 2010
- 27 - Revision E
11.2.12 Fast Read Dual I/O (BBh)
The Fast Read Dual I/O (BBh) instruction allows for improved random access while maintaining two IO
pins, IO0 and IO1. It is similar to the Fast Read Dual Output (3Bh) instruction but with the capability to
input the Address bits (A23-0) two bits per clock. This reduced instruction overhead may allow for code
execution (XIP) directly from the Dual SPI in some applications. To ensure optimum performance the
High Performance Mode (HPM) instruction (A3h) must be executed once, prior to the Fast Read Dual I/O
Instruction.
Fast Read Dual I/O with “Continuous Read Mode”
The Fast Read Dual I/O instruction can further reduce instruction overhead through setting the
“Continuous Read Mode” bits (M7-0) after the input Address bits (A23-0), as shown in figure 12a. The
upper nibble of the (M7-4) controls the length of the next Fast Read Dual I/O instruction through the
inclusion or exclusion of the first byte instruction code. The lower nibble bits of the (M3-0) are don’t care
(“x”). However, the IO pins should be high-impedance prior to the falling edge of the first data out clock.
If the “Continuous Read Mode” bits (M7-0) equals “Ax” hex, then the next Fast Read Dual I/O instruction
(after /CS is raised and then lowered) does not require the BBh instruction code, as shown in figure 12b.
This reduces the instruction sequence by eight clocks and allows the Read address to be immediately
entered after /CS is asserted low. If the “Continuous Read Mode” bits (M7-0) are any value other than
“Ax” hex, the next instruction (after /CS is raised and then lowered) requires the first byte instruction code,
thus returning to normal operation. A “Continuous Read Mode” Reset instruction can be used to reset
(M7-0) before issuing normal instructions (See 11.2.29 for detailed descriptions).
Figure 12a. Fast Read Dual Input/Output Instruction Sequence Diagram (M7-0 = 0xh or NOT Axh)
W25Q64BV
- 28 -
Figure 12b. Fast Read Dual Input/Output Instruction Sequence Diagram (M7-0 = Axh)
W25Q64BV
Publication Release Date: July 08, 2010
- 29 - Revision E
11.2.13 Fast Read Quad I/O (EBh)
The Fast Read Quad I/O (EBh) instruction is similar to the Fast Read Dual I/O (BBh) instruction except
that address and data bits are input and output through four pins IO0, IO1, IO2 and IO3 and four Dummy
clocks are required prior to the data output. The Quad I/O dramatically reduces instruction overhead
allowing faster random access for code execution (XIP) directly from the Quad SPI. The Quad Enable bit
(QE) of Status Register-2 must be set to enable the Fast read Quad I/O Instruction. To ensure optimum
performance the High Performance Mode (HPM) instruction (A3h) must be executed once, prior to the
Fast Read Quad I/O Instruction.
Fast Read Quad I/O with “Continuous Read Mode”
The Fast Read Quad I/O instruction can further reduce instruction overhead through setting the
“Continuous Read Mode” bits (M7-0) after the input Address bits (A23-0), as shown in figure 13a. The
upper nibble of the (M7-4) controls the length of the next Fast Read Quad I/O instruction through the
inclusion or exclusion of the first byte instruction code. The lower nibble bits of the (M3-0) are don’t care
(“x”). However, the IO pins should be high-impedance prior to the falling edge of the first data out clock.
If the “Continuous Read Mode” bits (M7-0) equals “Ax” hex, then the next Fast Read Quad I/O instruction
(after /CS is raised and then lowered) does not require the EBh instruction code, as shown in figure 13b.
This reduces the instruction sequence by eight clocks and allows the Read address to be immediately
entered after /CS is asserted low. If the “Continuous Read Mode” bits (M7-0) are any value other than
“Ax” hex, the next instruction (after /CS is raised and then lowered) requires the first byte instruction code,
thus returning to normal operation. A “Continuous Read Mode” Reset instruction can be used to reset
(M7-0) before issuing normal instructions (See 11.2.29 for detailed descriptions).
Byte 1 Byte 2Byte 1 Byte 2
Figure 13a. Fast Read Quad Input/Output Instruction Sequence Diagram (M7-0 = 0xh or NOT Axh)
W25Q64BV
- 30 -
Figure 13b. Fast Read Quad Input/Output Instruction Sequence Diagram (M7-0 = Axh)
W25Q64BV
Publication Release Date: July 08, 2010
- 31 - Revision E
11.2.14 Octal Word Read Quad I/O (E3h)
The Octal Word Read Quad I/O (E3h) instruction is similar to the Fast Read Quad I/O (EBh) instruction
except that the lower four Address bits (A0, A1, A2, A3) must equal 0. As a result, the four dummy clocks
are not required, which further reduces the instruction overhead allowing even faster random access for
code execution (XIP). The Quad Enable bit (QE) of Status Register-2 must be set to enable the Octal
Word Read Quad I/O Instruction. To ensure optimum performance the High Performance Mode
(HPM)instruction (A3h) must be executed once, prior to the Octal Word Read Quad I/O Instruction.
Octal Word Read Quad I/O with “Continuous Read Mode”
The Octal Word Read Quad I/O instruction can further reduce instruction overhead through setting the
“Continuous Read Mode” bits (M7-0) after the input Address bits (A23-0), as shown in figure 14a. The
upper nibble of the (M7-4) controls the length of the next Octal Word Read Quad I/O instruction through
the inclusion or exclusion of the first byte instruction code. The lower nibble bits of the (M3-0) are don’t
care (“x”). However, the IO pins should be high-impedance prior to the falling edge of the first data out
clock.
If the “Continuous Read Mode” bits (M7-0) equals “Ax” hex, then the next Octal Word Read Quad I/O
instruction (after /CS is raised and then lowered) does not require the E3h instruction code, as shown in
figure 14b. This reduces the instruction sequence by eight clocks and allows the Read address to be
immediately entered after /CS is asserted low. If the “Continuous Read Mode” bits (M7-0) are any value
other than “Ax” hex, the next instruction (after /CS is raised and then lowered) requires the first byte
instruction code, thus returning to normal operation. A “Continuous Read Mode” Reset instruction can be
used to reset (M7-0) before issuing normal instructions (See 11.2.29 for detailed descriptions).
Figure 14a. Octal Word Read Quad I/O Instruction Sequence (M7-0 = 0xh or NOT Axh)
Instruction (E3h)
Byte 1 Byte 2 Byte 3
4040
40
5151
51
6262
62
7373
73
40
51
62
73
Byte 4
Instruction (E3h)
Byte 1 Byte 2 Byte 3
40404040
4040
51515151
5151
62626262
6262
73737373
7373
4040
5151
6262
7373
Byte 4
W25Q64BV
- 32 -
Figure 14b. Octal Word Read Quad I/O Instruction Sequence (M7-0 = Axh)
Byte 2 Byte 3 Byte 4
404040
515151
626262
737373
Byte 1
40
51
62
73
Byte 2 Byte 3 Byte 4
40
4040
4040
40
51
5151
5151
51
62
6262
6262
62
73
7373
7373
73
Byte 1
40
40
51
51
62
62
73
73
W25Q64BV
Publication Release Date: July 08, 2010
- 33 - Revision E
11.2.15 Page Program (02h)
The Page Program instruction allows from one byte to 256 bytes (a page) of data to be programmed at
previously erased (FFh) memory locations. A Write Enable instruction must be executed before the
device will accept the Page Program Instruction (Status Register bit WEL= 1). The instruction is initiated
by driving the /CS pin low then shifting the instruction code “02h” followed by a 24-bit address (A23-A0)
and at least one data byte, into the DI pin. The /CS pin must be held low for the entire length of the
instruction while data is being sent to the device. The Page Program instruction sequence is shown in
figure 15.
If an entire 256 byte page is to be programmed, the last address byte (the 8 least significant address bits)
should be set to 0. If the last address byte is not zero, and the number of clocks exceed the remaining
page length, the addressing will wrap to the beginning of the page. In some cases, less than 256 bytes (a
partial page) can be programmed without having any effect on other bytes within the same page. One
condition to perform a partial page program is that the number of clocks can not exceed the remaining
page length. If more than 256 bytes are sent to the device the addressing will wrap to the beginning of the
page and overwrite previously sent data.
As with the write and erase instructions, the /CS pin must be driven high after the eighth bit of the last
byte has been latched. If this is not done the Page Program instruction will not be executed. After /CS is
driven high, the self-timed Page Program instruction will commence for a time duration of tpp (See AC
Characteristics). While the Page Program cycle is in progress, the Read Status Register instruction may
still be accessed for checking the status of the BUSY bit. The BUSY bit is a 1 during the Page Program
cycle and becomes a 0 when the cycle is finished and the device is ready to accept other instructions
again. After the Page Program cycle has finished the Write Enable Latch (WEL) bit in the Status Register
is cleared to 0. The Page Program instruction will not be executed if the addressed page is protected by
the Block Protect (BP2, BP1, and BP0) bits.
Figure 15. Page Program Instruction Sequence Diagram
W25Q64BV
- 34 -
11.2.16 Quad Input Page Program (32h)
The Quad Page Program instruction allows up to 256 bytes of data to be programmed at previously
erased (FFh) memory locations using four pins: IO0, IO1, IO2, and IO3. The Quad Page Program can
improve performance for PROM Programmer and applications that have slow clock speeds <5MHz.
Systems with faster clock speed will not realize much benefit for the Quad Page Program instruction
since the inherent page program time is much greater than the time it take to clock-in the data.
To use Quad Page Program the Quad Enable in Status Register-2 must be set (QE=1). A Write Enable
instruction must be executed before the device will accept the Quad Page Program instruction (Status
Register-1, WEL=1). The instruction is initiated by driving the /CS pin low then shifting the instruction
code “32h” followed by a 24-bit address (A23-A0) and at least one data byte, into the IO pins. The /CS pin
must be held low for the entire length of the instruction while data is being sent to the device. All other
functions of Quad Page Program are identical to standard Page Program. The Quad Page Program
instruction sequence is shown in figure 16.
Figure 16. Quad Input Page Program Instruction Sequence Diagram
W25Q64BV
Publication Release Date: July 08, 2010
- 35 - Revision E
11.2.17 Sector Erase (20h)
The Sector Erase instruction sets all memory within a specified sector (4K-bytes) to the erased state of all
1s (FFh). A Write Enable instruction must be executed before the device will accept the Sector Erase
Instruction (Status Register bit WEL must equal 1). The instruction is initiated by driving the /CS pin low
and shifting the instruction code “20h” followed a 24-bit sector address (A23-A0) (see Figure 2). The
Sector Erase instruction sequence is shown in figure 17.
The /CS pin must be driven high after the eighth bit of the last byte has been latched. If this is not done
the Sector Erase instruction will not be executed. After /CS is driven high, the self-timed Sector Erase
instruction will commence for a time duration of tSE (See AC Characteristics). While the Sector Erase
cycle is in progress, the Read Status Register instruction may still be accessed for checking the status of
the BUSY bit. The BUSY bit is a 1 during the Sector Erase cycle and becomes a 0 when the cycle is
finished and the device is ready to accept other instructions again. After the Sector Erase cycle has
finished the Write Enable Latch (WEL) bit in the Status Register is cleared to 0. The Sector Erase
instruction will not be executed if the addressed page is protected by the Block Protect (SEC, TB, BP2,
BP1, and BP0) bits (see Status Register Memory Protection table).
Figure 17. Sector Erase Instruction Sequence Diagram
W25Q64BV
- 36 -
11.2.18 32KB Block Erase (52h)
The Block Erase instruction sets all memory within a specified block (32K-bytes) to the erased state of all
1s (FFh). A Write Enable instruction must be executed before the device will accept the Block Erase
Instruction (Status Register bit WEL must equal 1). The instruction is initiated by driving the /CS pin low
and shifting the instruction code “52h” followed a 24-bit block address (A23-A0) (see Figure 2). The Block
Erase instruction sequence is shown in figure 18.
The /CS pin must be driven high after the eighth bit of the last byte has been latched. If this is not done
the Block Erase instruction will not be executed. After /CS is driven high, the self-timed Block Erase
instruction will commence for a time duration of tBE1 (See AC Characteristics). While the Block Erase
cycle is in progress, the Read Status Register instruction may still be accessed for checking the status of
the BUSY bit. The BUSY bit is a 1 during the Block Erase cycle and becomes a 0 when the cycle is
finished and the device is ready to accept other instructions again. After the Block Erase cycle has
finished the Write Enable Latch (WEL) bit in the Status Register is cleared to 0. The Block Erase
instruction will not be executed if the addressed page is protected by the Block Protect (SEC, TB, BP2,
BP1, and BP0) bits (see Status Register Memory Protection table).
Figure 18. 32KB Block Erase Instruction Sequence Diagram
W25Q64BV
Publication Release Date: July 08, 2010
- 37 - Revision E
11.2.19 64KB Block Erase (D8h)
The Block Erase instruction sets all memory within a specified block (64K-bytes) to the erased state of all
1s (FFh). A Write Enable instruction must be executed before the device will accept the Block Erase
Instruction (Status Register bit WEL must equal 1). The instruction is initiated by driving the /CS pin low
and shifting the instruction code “D8h” followed a 24-bit block address (A23-A0) (see Figure 2). The Block
Erase instruction sequence is shown in figure 19.
The /CS pin must be driven high after the eighth bit of the last byte has been latched. If this is not done
the Block Erase instruction will not be executed. After /CS is driven high, the self-timed Block Erase
instruction will commence for a time duration of tBE (See AC Characteristics). While the Block Erase cycle
is in progress, the Read Status Register instruction may still be accessed for checking the status of the
BUSY bit. The BUSY bit is a 1 during the Block Erase cycle and becomes a 0 when the cycle is finished
and the device is ready to accept other instructions again. After the Block Erase cycle has finished the
Write Enable Latch (WEL) bit in the Status Register is cleared to 0. The Block Erase instruction will not be
executed if the addressed page is protected by the Block Protect (SEC, TB, BP2, BP1, and BP0) bits (see
Status Register Memory Protection table).
Figure 19. 64KB Block Erase Instruction Sequence Diagram
W25Q64BV
- 38 -
11.2.20 Chip Erase (C7h / 60h)
The Chip Erase instruction sets all memory within the device to the erased state of all 1s (FFh). A Write
Enable instruction must be executed before the device will accept the Chip Erase Instruction (Status
Register bit WEL must equal 1). The instruction is initiated by driving the /CS pin low and shifting the
instruction code “C7h” or “60h”. The Chip Erase instruction sequence is shown in figure 20.
The /CS pin must be driven high after the eighth bit has been latched. If this is not done the Chip Erase
instruction will not be executed. After /CS is driven high, the self-timed Chip Erase instruction will
commence for a time duration of tCE (See AC Characteristics). While the Chip Erase cycle is in progress,
the Read Status Register instruction may still be accessed to check the status of the BUSY bit. The
BUSY bit is a 1 during the Chip Erase cycle and becomes a 0 when finished and the device is ready to
accept other instructions again. After the Chip Erase cycle has finished the Write Enable Latch (WEL) bit
in the Status Register is cleared to 0. The Chip Erase instruction will not be executed if any section of the
array is protected by the Block Protect (BP2, BP1, and BP0) bits (see Status Register Memory Protection
table).
Figure 20. Chip Erase Instruction Sequence Diagram
W25Q64BV
Publication Release Date: July 08, 2010
- 39 - Revision E
11.2.21 Erase Suspend (75h)
The Erase Suspend instruction “75h”, allows the system to interrupt a Sector or Block Erase operation
and then read from or program data to, any other sectors or blocks. The Erase Suspend instruction
sequence is shown in figure 21.
The Write Status Register instruction (01h) and Erase instructions (20h, 52h, D8h, C7h, 60h) are not
allowed during Erase Suspend. Erase Suspend is valid only during the Sector or Block erase operation. If
written during the Chip Erase or Program operation, the Erase Suspend instruction is ignored.
The Erase Suspend instruction “75h” will be accepted by the device only if the SUS bit in the Status
Register equals to 0 and the BUSY bit equals to 1 while a Sector or Block Erase is on-going. If the SUS
bit equals to 1 or the BUSY bit equals to 0, the Suspend instruction will be ignored by the device. A
maximum of time of “tSUS” (See AC Characteristics) is required to suspend the erase operation. The
BUSY bit in the Status Register will be cleared from 1 to 0 within “tSUS” and the SUS bit in the Status
Register will be set from 0 to 1 immediately after Erase Suspend. For a previously resumed Erase
operation, it is also required that the Suspend instruction “75h” is not issued earlier than a minimum of
time of “tSUS” following the preceding Resume instruction “7Ah”.
Unexpected power off during the Erase suspend state will reset the device and release the suspend
state. SUS bit in the Status Register will also reset to 0. The data within the sector or block that was being
suspended may become corrupted. It is recommended for the user to implement system design
techniques against the accidental power interruption and preserve data integrity during erase suspend
state.
Figure 21. Erase Suspend Instruction Sequence
W25Q64BV
- 40 -
11.2.22 Erase Resume (7Ah)
The Erase Resume instruction “7Ah” must be written to resume the Sector or Block Erase operation after
an Erase Suspend. The Resume instruction “7Ah” will be accepted by the device only if the SUS bit in the
Status Register equals to 1 and the BUSY bit equals to 0. After issued the SUS bit will be cleared from 1
to 0 immediately, the BUSY bit will be set from 0 to 1 within 200ns and the Sector or Block will complete
the erase operation. If the SUS bit equals to 0 or the BUSY bit equals to 1, the Resume instruction “7Ah”
will be ignored by the device. The Erase Resume instruction sequence is shown in figure 22.
Resume instruction is ignored if the previous Erase Suspend operation was interrupted by unexpected
power off. It is also required that a subsequent Erase Suspend instruction not to be issued within a
minimum of time of “tSUS” following a previous Resume instruction.
Figure 22. Erase Resume Instruction Sequence
W25Q64BV
Publication Release Date: July 08, 2010
- 41 - Revision E
11.2.23 Power-down (B9h)
Although the standby current during normal operation is relatively low, standby current can be further
reduced with the Power-down instruction. The lower power consumption makes the Power-down
instruction especially useful for battery powered applications (See ICC1 and ICC2 in AC Characteristics).
The instruction is initiated by driving the /CS pin low and shifting the instruction code “B9h” as shown in
figure 23.
The /CS pin must be driven high after the eighth bit has been latched. If this is not done the Power-down
instruction will not be executed. After /CS is driven high, the power-down state will entered within the time
duration of tDP (See AC Characteristics). While in the power-down state only the Release from Power-
down / Device ID instruction, which restores the device to normal operation, will be recognized. All other
instructions are ignored. This includes the Read Status Register instruction, which is always available
during normal operation. Ignoring all but one instruction makes the Power Down state a useful condition
for securing maximum write protection. The device always powers-up in the normal operation with the
standby current of ICC1.
Figure 23. Deep Power-down Instruction Sequence Diagram
W25Q64BV
- 42 -
11.2.24 High Performance Mode (A3h)
The High Performance Mode (HPM) instruction must be executed prior to Dual or Quad I/O instructions
when operating at high frequencies (see FR and FR1 in AC Electrical Characteristics). This instruction
allows pre-charging of internal charge pumps so the voltages required for accessing the Flash memory
array are readily available. The instruction sequence includes the A3h instruction code followed by three
dummy byte clocks shown in Fig. 24. After the HPM instruction is executed, the device will maintain a
slightly higher standby current (Icc3) than standard SPI operation. The Release from Power-down or
HPM instruction (ABh) can be used to return to standard SPI standby current (Icc1). In addition, Write
Enable instruction (06h) and Power Down instruction (B9h) will also release the device from HPM mode
back to standard SPI standby state.
Figure 24. High Performance Mode Instruction Sequence
11.2.25 Release Power-down or High Performance Mode / Device ID (ABh)
The Release from Power-down or High performance Mode / Device ID instruction is a multi-purpose
instruction. It can be used to release the device from the power-down state or High Performance Mode,
or obtain the devices electronic identification (ID) number.
To release the device from the power-down state or High Performance Mode, the instruction is issued by
driving the /CS pin low, shifting the instruction code “ABh” and driving /CS high as shown in figure 25.
Release from power-down will take the time duration of tRES1 (See AC Characteristics) before the device
will resume normal operation and other instructions are accepted. The /CS pin must remain high during
the tRES1 time duration.
When used only to obtain the Device ID while not in the power-down state, the instruction is initiated by
driving the /CS pin low and shifting the instruction code “ABh” followed by 3-dummy bytes. The Device ID
bits are then shifted out on the falling edge of CLK with most significant bit (MSB) first as shown in figure
26. The Device ID values for the W25Q64BV is listed in Manufacturer and Device Identification table. The
Device ID can be read continuously. The instruction is completed by driving /CS high.
W25Q64BV
When used to release the device from the power-down state and obtain the Device ID, the instruction is
the same as previously described, and shown in figure 26, except that after /CS is driven high it must
remain high for a time duration of tRES2 (See AC Characteristics). After this time duration the device will
resume normal operation and other instructions will be accepted. If the Release from Power-down /
Device ID instruction is issued while an Erase, Program or Write cycle is in process (when BUSY equals
1) the instruction is ignored and will not have any effects on the current cycle.
Figure 25. Release Power-down/High Performance Mode Instruction Sequence
Figure 26. Release Power-down / Device ID Instruction Sequence Diagram
Publication Release Date: July 08, 2010
- 43 - Revision E
W25Q64BV
- 44 -
11.2.26 Read Manufacturer / Device ID (90h)
The Read Manufacturer/Device ID instruction is an alternative to the Release from Power-down / Device
ID instruction that provides both the JEDEC assigned manufacturer ID and the specific device ID.
The Read Manufacturer/Device ID instruction is very similar to the Release from Power-down / Device ID
instruction. The instruction is initiated by driving the /CS pin low and shifting the instruction code “90h”
followed by a 24-bit address (A23-A0) of 000000h. After which, the Manufacturer ID for Winbond (EFh)
and the Device ID are shifted out on the falling edge of CLK with most significant bit (MSB) first as shown
in figure 27. The Device ID values for the W25Q64BV is listed in Manufacturer and Device Identification
table. If the 24-bit address is initially set to 000001h the Device ID will be read first and then followed by
the Manufacturer ID. The Manufacturer and Device IDs can be read continuously, alternating from one to
the other. The instruction is completed by driving /CS high.
31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 4631 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46
Figure 27. Read Manufacturer / Device ID Diagram
W25Q64BV
Publication Release Date: July 08, 2010
- 45 - Revision E
11.2.27 Read Unique ID Number (4Bh)(1)
The Read Unique ID Number instruction accesses a factory-set read-only 64-bit number that is unique to
each W25Q64BV device. The ID number can be used in conjunction with user software methods to help
prevent copying or cloning of a system. The Read Unique ID instruction is initiated by driving the /CS pin
low and shifting the instruction code “4Bh” followed by a four bytes of dummy clocks. After which, the 64-
bit ID is shifted out on the falling edge of CLK as shown in figure 28.
24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 101 102 103
DO
63 62 61 60 59 2 1 0
*
*=MSB
DO
24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 101 102 103
DO
63 62 61 60 59 2 1 0
*
*=MSB
DO
Figure 28. Read Unique ID Number Instruction Sequence
Note:
1. For W25Q64BV, this feature is available upon special request. Please contact Winbond for details.
W25Q64BV
- 46 -
11.2.28 Read JEDEC ID (9Fh)
For compatibility reasons, the W25Q64BV provides several instructions to electronically determine the
identity of the device. The Read JEDEC ID instruction is compatible with the JEDEC standard for SPI
compatible serial memories that was adopted in 2003. The instruction is initiated by driving the /CS pin
low and shifting the instruction code “9Fh”. The JEDEC assigned Manufacturer ID byte for Winbond (EFh)
and two Device ID bytes, Memory Type (ID15-ID8) and Capacity (ID7-ID0) are then shifted out on the
falling edge of CLK with most significant bit (MSB) first as shown in figure 29. For memory type and
capacity values refer to Manufacturer and Device Identification table.
15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 3115 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31
Figure 29. Read JEDEC ID Instruction Sequence Diagram
W25Q64BV
Publication Release Date: July 08, 2010
- 47 - Revision E
11.2.29 Continuous Read Mode Reset (FFh or FFFFh)
For Fast Read Dual/Quad I/O operations, “Continuous Read Mode” Bits (M7-0) are implemented to
further reduce instruction overhead. By setting the (M7-0) to “Ax” hex, the next Fast Read Dual/Quad I/O
operation does not require the BBh/EBh instruction code (See 11.2.12 Fast Read Dual I/O and 11.2.13
Fast Read Quad I/O for detail descriptions).
If the system controller is Reset during operation it will likely send a standard SPI instruction, such
as Read ID (9Fh) or Fast Read (0Bh), to the W25Q64BV. However, as with most SPI Serial Flash
memories, the W25Q64BV does not have a hardware Reset pin, so if Continuous Read Mode bits are set
to “Ax” hex, the W25Q64BV will not recognize any standard SPI instructions. To address this possibility, it
is recommended to issue a Continuous Read Mode Reset instruction as the first instruction after a
system Reset. Doing so will release the Continuous Read Mode from the “Ax” hex state and allow
Standard SPI instructions to be recognized. The Continuous Read Mode Reset instruction is shown in
figure 30.
/CS
Mode Bit Reset
for Dual I/O
Mode 3
Mode 0
0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 Mode 3
Mode 0
Mode Bit Reset
for Quad I/O
FFh FFh
Don’t Care
Don’t Care
CLK
IO
0
IO
1
IO
2
/CS
Mode Bit Reset
for Dual I/O
Mode 3
Mode 0
0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 Mode 3
Mode 0
Mode Bit Reset
for Quad I/O
FFh FFh
Don’t Care
Don’t Care
Don’t Care
IO
3
Don’t Care
IO
3
CLK
IO
0
IO
1
IO
2
Figure 30. Continuous Read Mode Reset for Fast Read Dual/Quad I/O
To reset “Continuous Read Mode” during Quad I/O operation, only eight clocks are needed. The
instruction is “FFh”. To reset “Continuous Read Mode” during Dual I/O operation, sixteen clocks are
needed to shift in instruction “FFFFh”.
W25Q64BV
- 48 -
12. ELECTRICAL CHARACTERISTICS
12.1 Absolute Maximum Ratings (1)
PARAMETERS SYMBOL CONDITIONS RANGE UNIT
Supply Voltage VCC –0.6 to +4.0 V
Voltage Applied to Any Pin VIO Relative to Ground –0.6 to VCC+0.4 V
Transient Voltage on any Pin VIOT <20nS Transient
Relative to Ground –2.0V to VCC+2.0V V
Storage Temperature TSTG –65 to +150 °C
Lead Temperature TLEAD See Note
(2) °C
Electrostatic Discharge Voltage VESD Human Body Model(3) –2000 to +2000 V
Notes:
1. This device has been designed and tested for the specified operation ranges. Proper operation outside
of these levels is not guaranteed. Exposure to absolute maximum ratings may affect device reliability.
Exposure beyond absolute maximum ratings may cause permanent damage.
2. Compliant with JEDEC Standard J-STD-20C for small body Sn-Pb or Pb-free (Green) assembly and
the European directive on restrictions on hazardous substances (RoHS) 2002/95/EU.
3. JEDEC Std JESD22-A114A (C1=100pF, R1=1500 ohms, R2=500 ohms).
12.2 Operating Ranges
SPEC
PARAMETER SYMBOL CONDITIONS MIN MAX UNIT
Supply Voltage(1) VCC
FR = 80MHz, fR = 33MHz
FR = 50MHz (for E3h command)
2.7
3.0
3.6
3.6 V
Ambient Temperature, Operating TA Commercial
Industrial
0
–40
+70
+85 °C
Note:
1. VCC voltage during Read can operate across the min and max range but should not exceed ±10% of
the programming (erase/write) voltage.
W25Q64BV
Publication Release Date: July 08, 2010
- 49 - Revision E
12.3 Power-up Timing and Write Inhibit Threshold
SPEC
PARAMETER SYMBOL
MIN MAX
UNIT
VCC (min) to /CS Low tVSL(1) 10 µs
Time Delay Before Write Instruction tPUW(1) 1 10 ms
Write Inhibit Threshold Voltage VWI(1) 1 2 V
Note:
1. These parameters are characterized only.
Figure 31. Power-up Timing and Voltage Levels
W25Q64BV
- 50 -
12.4 DC Electrical Characteristics
SPEC
PARAMETER SYMBOL CONDITIONS MIN TYP MAX
UNIT
Input Capacitance CIN(1) VIN = 0V(1) 6 pF
Output Capacitance Cout(1) VOUT = 0V(1) 8 pF
Input Leakage ILI ±2 µA
I/O Leakage ILO ±2 µA
Standby Current ICC1 /CS = VCC,
VIN = GND or VCC 25 50 µA
Power-down Current ICC2 /CS = VCC,
VIN = GND or VCC 1 5 µA
High performance
current ICC3 After enable High
Performance mode 50 100 µA
Current Read Data /
Dual /Quad 1MHz(2) ICC4 C = 0.1 VCC / 0.9 VCC
DO = Open 4/5/6 6/7.5/9 mA
Current Read Data /
Dual /Quad 33MHz(2) ICC4 C = 0.1 VCC / 0.9 VCC
DO = Open 6/7/8 9/10.5/12 mA
Current Read Data /
Dual /Quad 50MHz(2) ICC4 C = 0.1 VCC / 0.9 VCC
DO = Open 7/8/9 10/12/13.5 mA
Current Read Data /
Dual Output Read/Quad
Output Read 80MHz(2)
ICC4 C = 0.1 VCC / 0.9 VCC
DO = Open 10/11/12 15/16.5/18 mA
Current Write Status
Register ICC6 /CS = VCC 8 12 mA
Current Page Program ICC7 /CS = VCC 20 25 mA
Current Sector/Block
Erase ICC8 /CS = VCC 20 25 mA
Current Chip Erase ICC9 /CS = VCC 20 25 mA
Input Low Voltage VIL VCC x 0.3 V
Input High Voltage VIH VCC x 0.7 V
Output Low Voltage VOL IOL = 1.6 mA 0.4 V
Output High Voltage VOH IOH = –100 µA VCC – 0.2 V
Notes:
1. Tested on sample basis and specified through design and characterization data. TA=25° C, VCC 3V.
2. Checker Board Pattern.
W25Q64BV
Publication Release Date: July 08, 2010
- 51 - Revision E
12.5 AC Measurement Conditions
SPEC
PARAMETER SYMBOL
MIN MAX
UNIT
Load Capacitance CL 30 pF
Input Rise and Fall Times TR, TF 5 ns
Input Pulse Voltages VIN 0.2 VCC to 0.8 VCC V
Input Timing Reference Voltages IN 0.3 VCC to 0.7 VCC V
Output Timing Reference Voltages OUT 0.5 VCC to 0.5 VCC V
Note:
1. Output Hi-Z is defined as the point where data out is no longer driven.
Figure 32. AC Measurement I/O Waveform
W25Q64BV
- 52 -
12.6 AC Electrical Characteristics
SPEC
DESCRIPTION SYMBOL ALT
MIN TYP MAX
UNIT
Clock frequency for all instructions,
except Read Data (03h) & Octal Word Read (E3h)
2.7V-3.6V VCC & Industrial Temperature
FR f
C D.C. 80 MHz
Clock frequency
for Octal Word Read Quad I/O (E3h)
3.0V-3.6V VCC & Industrial Temperature
FR f
C D.C. 50 MHz
Clock freq. Read Data instruction (03h) fR D.C. 33 MHz
Clock High, Low Time except Read Data (03h) tCLH,
tCLL(1)
6 ns
Clock High, Low Time for Read Data (03h)
instruction
tCRLH,
tCRLL(1)
8
8
ns
Clock Rise Time peak to peak tCLCH(2) 0.1 V/ns
Clock Fall Time peak to peak tCHCL(2) 0.1 V/ns
/CS Active Setup Time relative to CLK tSLCH tCSS 5 ns
/CS Not Active Hold Time relative to CLK tCHSL 5 ns
Data In Setup Time tDVCH tDSU 2 ns
Data In Hold Time tCHDX tDH 5 ns
/CS Active Hold Time relative to CLK tCHSH 5 ns
/CS Not Active Setup Time relative to CLK tSHCH 5 ns
/CS Deselect Time (for Array Read Æ Array Read /
Erase or Program Æ Read Status Registers)
tSHSL tCSH 10/50 ns
Output Disable Time tSHQZ(2) tDIS 7 ns
Clock Low to Output Valid
2.7V-3.6V / 3.0V-3.6V tCLQV1 tV1 7/6 ns
Clock Low to Output Valid (for Read ID instructions)
2.7V-3.6V / 3.0V-3.6V tCLQV2 tV2 8.5 / 7.5 ns
Output Hold Time tCLQX tHO 0 ns
/HOLD Active Setup Time relative to CLK tHLCH 5 ns
Continued – next page
W25Q64BV
Publication Release Date: July 08, 2010
- 53 - Revision E
12.7 AC Electrical Characteristics (cont’d)
SPEC
DESCRIPTION SYMBOL ALT
MIN TYP MAX
UNIT
/HOLD Active Hold Time relative to CLK tCHHH 5 ns
/HOLD Not Active Setup Time relative to CLK tHHCH 5 ns
/HOLD Not Active Hold Time relative to CLK tCHHL 5 ns
/HOLD to Output Low-Z tHHQX(2) tLZ 7 ns
/HOLD to Output High-Z tHLQZ(2) tHZ 12 ns
Write Protect Setup Time Before /CS Low tWHSL(3) 20 ns
Write Protect Hold Time After /CS High tSHWL(3) 100 ns
/CS High to Power-down Mode tDP(2) 3 µs
/CS High to Standby Mode without Electronic Signature
Read
tRES1(2) 3 µs
/CS High to Standby Mode with Electronic Signature
Read
tRES2(2) 1.8 µs
/CS High to next Instruction after Suspend tSUS(2) 20 µs
Write Status Register Time tW 10 15 ms
Byte Program Time (First Byte) (4) t
BP1 20 50 µs
Additional Byte Program Time (After First Byte) (4) t
BP2 2.5 12 µs
Page Program Time tPP 0.7 3 ms
Sector Erase Time (4KB) tSE 30 200/400(5) ms
Block Erase Time (32KB) tBE1 120 800 ms
Block Erase Time (64KB) tBE2 150 1000 ms
Chip Erase Time tCE 15 30 s
Notes:
1. Clock high + Clock low must be less than or equal to 1/fC.
2. Value guaranteed by design and/or characterization, not 100% tested in production.
3. Only applicable as a constraint for a Write Status Register instruction when Sector Protect Bit is set to 1.
4. For multiple bytes after first byte within a page, tBPN = t
BP1 + tBP2 * N (typical) and tBPN = t
BP1 + tBP2 * N (max), where N =
number of bytes programmed.
5. Max Value tSE with <50K cycles is 200ms and >50K & <100K cycles is 400ms.
W25Q64BV
- 54 -
12.8 Serial Output Timing
12.9 Input Timing
12.10 Hold Timing
W25Q64BV
Publication Release Date: July 08, 2010
- 55 - Revision E
13. PACKAGE SPECIFICATION
13.1 8-Pin SOIC 208-mil (Package Code SS)
θ
GAUGE PLANE
θ
GAUGE PLANE
MILLIMETERS INCHES
SYMBOL Min Nom Max Min Nom Max
A 1.75 1.95 2.16 0.069 0.077 0.085
A1 0.05 0.15 0.25 0.002 0.006 0.010
A2 1.70 1.80 1.91 0.067 0.071 0.075
b 0.35 0.42 0.48 0.014 0.017 0.019
C 0.19 0.20 0.25 0.007 0.008 0.010
D 5.18 5.28 5.38 0.204 0.208 0.212
D1 5.13 5.23 5.33 0.202 0.206 0.210
E 5.18 5.28 5.38 0.204 0.208 0.212
E1 5.13 5.23 5.33 0.202 0.206 0.210
e(2) 1.27 BSC. 0.050 BSC.
H 7.70 7.90 8.10 0.303 0.311 0.319
L 0.50 0.65 0.80 0.020 0.026 0.031
y --- --- 0.10 --- --- 0.004
θ 0° --- 8° 0° --- 8°
Notes:
1. Controlling dimensions: millimeters, unless otherwise specified.
2. BSC = Basic lead spacing between centers.
3. Dimensions D1 and E1 do not include mold flash protrusions and should be measured from the bottom of the package.
4. Formed leads coplanarity with respect to seating plane shall be within 0.004 inches.
W25Q64BV
- 56 -
13.2 8-Pin PDIP 300-mil (Package Code DA)
MILLIMETERS INCHES
SYMBO
L Min Nom Max Min Nom Max
A --- --- 5.33 --- --- 0.210
A1 0.38 --- --- 0.015 --- ---
A2 3.18 3.30 3.43 0.125 0.130 0.135
D 9.02 9.27 10.16 0.355 0.365 0.400
E 7.62 BSC. 0.300 BSC.
E1 6.22 6.35 6.48 0.245 0.250 0.255
L 2.92 3.30 3.81 0.115 0.130 0.150
eB 8.51 9.02 9.53 0.335 0.355 0.375
θ° 7° 15° 0° 7° 15°
W25Q64BV
Publication Release Date: July 08, 2010
- 57 - Revision E
13.3 8-Contact 8x6mm WSON (Package Code ZE)
MILLIMETERS INCHES
SYMBOL Min Nom Max Min Nom Max
A 0.70 0.75 0.80 0.028 0.030 0.031
A1 0.00 0.02 0.05 0.000 0.001 0.002
b 0.35 0.40 0.48 0.014 0.016 0.019
C 0.19 0.20 0.25 0.007 0.008 0.010
D 7.90 8.00 8.10 0.311 0.315 0.319
D2 4.60 4.65 4.70 0.181 0.183 0.185
E 5.90 6.00 6.10 0.232 0.236 0.240
E2 5.15 5.20 5.25 0.203 0.205 0.207
e 1.27 BSC 0.050 BSC
L 0.45 0.50 0.55 0.018 0.020 0.022
y 0.00 --- 0.050 0.000 --- 0.002
W25Q64BV
- 58 -
13.4 16-Pin SOIC 300-mil (Package Code SF)
GAUGE PLANE
DETAIL A
GAUGE PLANE
DETAIL A
MILLIMETERS INCHES
SYMBOL Min Nom Max Min Nom Max
A 2.36 2.49 2.64 0.093 0.098 0.104
A1 0.10 --- 0.30 0.004 --- 0.012
A2 --- 2.31 --- --- 0.091 ---
b 0.33 0.41 0.51 0.013 0.016 0.020
C 0.18 0.23 0.28 0.007 0.009 0.011
D 10.08 10.31 10.49 0.397 0.406 0.413
E 10.01 10.31 10.64 0.394 0.406 0.419
E1 7.39 7.49 7.59 0.291 0.295 0.299
e(2) 1.27 BSC. 0.050 BSC.
L 0.38 0.81 1.27 0.015 0.032 0.050
y --- --- 0.076 --- --- 0.003
θ 0° --- ---
Notes:
1. Controlling dimensions: inches, unless otherwise specified.
2. BSC = Basic lead spacing between centers.
3. Dimensions D and E1 do not include mold flash protrusions and should be measured from the bottom of the package.
W25Q64BV
Publication Release Date: July 08, 2010
- 59 - Revision E
14. ORDERING INFORMATION (1)
W 25Q 64B V xx(1)
I = Industrial (-40°C to +85°C)
SS = 8-pin SOIC 208-mil DA = 8-pin PDIP 300-mil
SF = 16-pin SOIC 300-mil ZE = 8-pad WSON 8x6mm
V = 2.7V to 3.6V
64B = 64M-bit
25Q = SpiFlash Serial Flash Memory with 4KB sectors, Dual/Quad I/O
W = Winbond
G = Green Package (Lead-free, RoHS Compliant, Halogen-free (TBBA), Antimony-Oxide-free Sb2O3)
P = Green Package with Status Register Power-Down & OTP enabled
Notes:
1a. Only the 2nd letter is used for the part marking; WSON package type ZE is not used for the part marking.
1b. Standard bulk shipments are in Tube (shape E). Please specify alternate packing method, such as Tape and Reel (shape
T), when placing orders.
1c. The “W” prefix is not included on the part marking.
W25Q64BV
- 60 -
14.1 Valid Part Numbers and Top Side Marking
The following table provides the valid part numbers for the W25Q64BV SpiFlash Memory. Please contact
Winbond for specific availability by density and package type. Winbond SpiFlash memories use an 12-
digit Product Number for ordering. However, due to limited space, the Top Side Marking on all packages
use an abbreviated 10-digit number.
PACKAGE TYPE DENSITY PRODUCT NUMBER TOP SIDE MARKING
SS
SOIC-8 208mil 64M-bit W25Q64BVSSIG
W25Q64BVSSIP
25Q64BVSIG
25Q64BVSIP
SF
SOIC-16 300mil 64M-bit W25Q64BVSFIG
W25Q64BVSFIP
25Q64BVFIG
25Q64BVFIP
DA
PDIP-8 300mil 64M-bit W25Q64BVDAIG
W25Q64BVDAIP
25Q64BVAIG
25Q64BVAIP
ZE(1)
WSON-8 8x6mm 64M-bit W25Q64BVZEIG
W25Q64BVZEIP
25Q64BVIG
25Q64BVIP
Note:
1. WSON package type ZE is not used in the top side marking.
W25Q64BV
Publication Release Date: July 08, 2010
- 61 - Revision E
15. REVISION HISTORY
VERSION DATE PAGE DESCRIPTION
A 08/24/08 New Create Preliminary
B 01/15/09
03/12/09
3/13/09
56 & 57
57
5
13
P character added to end of a Part Number
Corrected Top Side Marking
Changed Active Current to 4mA
Typo Change QE pin to QE bit
C 08/20/09 38, 39, 54~56 &
58
44
Update Erase Suspend and Resume description.
Update Package Diagrams
UID Waveform Corrected
D 09/24/09 52
5,7,55,58,59
44
46
Change fR = 33Mhz
Added PDIP Package
Corrected Read Manufacturer / Device ID Fig 27.
Corrected Read JEDEC ID, Fig 29
E 07/08/10
61
55-58
50, 53
Removed Preliminary designator
Updated package diagrams
Updated parameter VIL/VIH, tBP1, tSE
Trademarks
Winbond and SpiFlash are trademarks of Winbond Electronics Corporation.
All other marks are the property of their respective owner.
Important Notice
Winbond products are not designed, intended, authorized or warranted for use as components in systems
or equipment intended for surgical implantation, atomic energy control instruments, airplane or spaceship
instruments, transportation instruments, traffic signal instruments, combustion control instruments, or for
other applications intended to support or sustain life. Further more, Winbond products are not intended
for applications wherein failure of Winbond products could result or lead to a situation wherein personal
injury, death or severe property or environmental damage could occur.
Winbond customers using or selling these products for use in such applications do so at their own risk
and agree to fully indemnify Winbond for any damages resulting from such improper use or sales.