KMY Last update: 2015.2.6 No.RVC-K-HTS-0001-9 (Uncontrolled copy) Sp e c i f i c a t i o n (Reference) Title: FIXED THICK FILM CHIP RESISTORS; RECTANGULAR TYPE AND HIGH VOLTAGE Style: RVC16,20,32,50,63 RoHS COMPLIANCE ITEM Product specification contained in this specification are subject to change at any time without notice If you have any questions or a Purchasing Specification for any quality Agreement is necessary, please contact our sales staff. Issue Dept.: Research & Development Department Hokkaido Research Center KMY Title: Drawing No: RVC-K-HTS-0001 FIXED THICK FILM CHIP RESISTORS; RECTANGULAR TYPE AND HIGH VOLTAGE RVC16,20,32,50,63 Page: /9 1/12 1. Scope 1.1 This specification covers the detail requirements for fixed thick film chip resistors; rectangular type, style of RVC16, 20, 32, 50, 63 1.2 Applicable documents JIS C 5201-1: 1998, JIS C 5201-8: 1998, JIS C 5201-8-1: 1998 IEC60115-1: 1999, IEC60115-8: 1989 Amendment 1: 1992, IEC60115-8-1: 1989 EIAJ RC-2134B-2002 2. Classification Type designation shall be the following form. (Example) RVC 32 475 F TP - 1 2 3 4 5 6 Style 1 Fixed thick film chip resistors; rectangular type and high voltage 2 Size K 3 Temperature coefficient of resistance 100x10-6/ C Standard -(Dash) 4 Rated resistance Example; 475 4.7M 5 Tolerance on rated resistance 6 Packaging form Style 3. Rating 3.1 The ratings shall be in accordance with Table-1. Table-1(1) Style RVC16 RVC20 RVC32 RVC50 RVC63 Rated dissipation (W) Temperature coefficient of resistance ( 10-6 / C) Rated resistance range() K 100 47010M Standard 200 47464 K 100 10010M 10051M Standard 200 4797.6 K 100 100k4.7M 10010M 10051M 0.1 0.25 0.25 Standard 200 4797.6 K 100 47020M 47051M Standard 200 47464 K 100 56020M 56051M 200 100549 +500-200 4797.6 0.5 1.0 Standard Preferred number series for resistors Tolerance on rated resistance E24, 96 E24 E24, 96 E24 E24, 96 E24 E24, 96 E24 F(1%), G(2%) J(5%), K(10%) F(1%), G(2%) J(5%), K(10%) F(1%), G(2%) J(5%), K(10%) F(1%), G(2%) J(5%), K(10%) D(0.5%) F(1%), G(2%) J(5%), K(10%) F(1%), G(2%) J(5%), K(10%) F(1%), G(2%) J(5%), K(10%) F(1%), G(2%) J(5%), K(10%) F(1%), G(2%) J(5%), K(10%) F(1%), G(2%) J(5%), K(10%) F(1%), G(2%) J(5%), K(10%) E24, 96 E24 E24, 96 E24 E24, 96 E24 E24, 96 E24 E24, 96 E24 E24, 96 E24 E24, 96 E24 Product specification contained in this specification are subject to change at any time without notice. If you have any questions or a Purchasing Specification for any quality agreement is necessary, please contact our sales staff. Issue: KAMAYA ELECTRIC CO., LTD. Research & Development Department HOKKAIDO Research center Last update: 2015.2.6 KMY Drawing No: RVC-K-HTS-0001 FIXED THICK FILM CHIP RESISTORS; RECTANGULAR TYPE AND HIGH VOLTAGE RVC16,20,32,50,63 Page: Title: /9 2/12 Table-1(2) Style Limiting element voltage(V) Isolation voltage (V) RVC16 RVC20 RVC32 RVC50 RVC63 200 400 500 500 800 100 3.2 Climatic category 55/125/56 3.3 Stability class 5% Category temperature range (C) -55+155 500 Lower category temperature Upper category temperature Duration of the damp heat, steady state test - 55 C +155 C 56days Limits for change of resistance: -for long-term tests (5%+0.1) -for short-term tests (1%+0.05) 3.4 Derating The derated values of dissipation at temperature in excess of 70 C shall be as indicated by the following curve. 100 Percentage of the rated dissipation Area of recommended operation (%) 0 -55 70 155 Ambient temperature (C) Figure-1 Derating curve 3.5 Rated voltage d. c. or a. c. r. m. s. voltage calculated from the square root of the product of the rated resistance and the rated dissipation. E : Rated voltage (V) E = P * R P : Rated dissipation (W) R : Rated resistance () Limiting element voltage can only be applied to resistors when the resistance value is equal to or higher than the critical resistance value. At high value of resistance, the rated voltage may not be applicable. 4. Packaging form The standard packaging form shall be in accordance with Table-2. Table-2 Symbol B TP TE Packaging form Bulk (loose package) Paper taping 8mm width, 4mm pitches Embossed taping 12mm width, 4mm pitches Standard packaging quantity / units 1,000 pcs. 5,000 pcs. 4,000 pcs. Application RVC16, 20, 32, 50, 63 RVC16, 20, 32 RVC50, 63 Product specification contained in this specification are subject to change at any time without notice. If you have any questions or a Purchasing Specification for any quality agreement is necessary, please contact our sales staff. Issue: KAMAYA ELECTRIC CO., LTD. Research & Development Department HOKKAIDO Research center Last update: 2015.2.6 KMY Title: Drawing No: RVC-K-HTS-0001 FIXED THICK FILM CHIP RESISTORS; RECTANGULAR TYPE AND HIGH VOLTAGE RVC16,20,32,50,63 Page: /9 3/12 W 5. Dimensions 5.1 The resistor shall be of the design and physical dimensions in accordance with Figure-2 and Table-3. L c d d H c Figure-2 Table-3 Style RVC16 L 1.6 0.1 W +0.15 0.8 -0.05 RVC20 2.0 0.1 1.25 0.10 RVC32 3.1 0.15 1.6 0.15 RVC50 RVC63 5.0 0.15 6.3 0.15 2.5 0.15 3.2 0.15 H 0.45 0.10 0.55 0.10 0.55 0.15 c 0.3 0.1 Unit : mm d 0.3 0.1 0.4 0.2 0.4 0.2 0.5 0.25 0.5 0.25 0.6 0.2 0.6 0.2 5.2 Net weight (Reference) Style Net weight(mg) RVC16 2 RVC20 5 RVC32 9 RVC50 25 RVC63 40 6. Marking The Rated resistance shall be marked in 3 digits (E24) or 4 digits (E96) and marked on over coat side. The Rated resistance of RVC16 should not be marked in 4 digits. (Example) "123" 12 x10 3 [] 12 [k] "5623" 562 x10 3 [] 562 [k] "51R1" 51.1 [] Product specification contained in this specification are subject to change at any time without notice. If you have any questions or a Purchasing Specification for any quality agreement is necessary, please contact our sales staff. Issue: KAMAYA ELECTRIC CO., LTD. Research & Development Department HOKKAIDO Research center Last update: 2015.2.6 KMY Title: Drawing No: RVC-K-HTS-0001 FIXED THICK FILM CHIP RESISTORS; RECTANGULAR TYPE AND HIGH VOLTAGE RVC16,20,32,50,63 Page: /9 4/12 7. Performance 7.1 The standard condition for tests shall be in accordance with Sub-clause 4.2, JIS C 5201-1: 1998. 7.2 The performance shall be satisfied in Table-4. Table-4(1) Test items Performance requirements No. Condition of test (JIS C 5201-1) 1 Visual examination As in 4.4.1 Sub-clause 4.4.1 The marking shall be legible, as Checked by visual examination. checked by visual examination. 2 Dimension As specified in Table-3 of this Sub-clause 4.4.2 specification. Resistance As in 4.5.2 Sub-clause 4.5 The resistance value shall correspond with the rated resistance taking into account the specified tolerance. 3 Voltage proof No breakdown or flash over Sub-clause 4.7 Method: 4.6.1.4(See Figure-5) Test voltage: Alternating voltage with a peak value of 1.42 times the insulation voltage. Duration: 60 s 5 s R1G Insulation resistance Test voltage: Insulation voltage Duration: 1 min. 4 Solderability As in 4.17.4.5 Sub-clause 4.17 The terminations shall be covered Without ageing Flux: The resistors shall be immersed in a with a smooth and bright solder coating. non-activated soldering flux for 2s. Bath temperature: 235 C 5 C Immersion time: 2 s 0.5 s 5 Mounting Sub-clause 4.31 Substrate material: Epoxide woven glass Test substrate: Figure-3 Sub-clause 4.13 Overload The applied voltage shall be 2.5 times the rated (in the mounted state) voltage or twice the limiting element voltage, whichever is the less severe. Duration: 2 s No visible damage Visual examination R (1%+0.05) Resistance Solvent resistance of the Sub-clause 4.30 Legible marking marking Solvent: 2-propanol Solvent temperature: 23 C 5 C Method 1 Rubbing material: cotton wool Without recovery Product specification contained in this specification are subject to change at any time without notice. If you have any questions or a Purchasing Specification for any quality agreement is necessary, please contact our sales staff. Issue: KAMAYA ELECTRIC CO., LTD. Research & Development Department HOKKAIDO Research center Last update: 2015.2.6 KMY Title: No 6 7 Drawing No: RVC-K-HTS-0001 FIXED THICK FILM CHIP RESISTORS; RECTANGULAR TYPE AND HIGH VOLTAGE RVC16,20,32,50,63 Page: Table-4(2) Condition of test (JIS C 5201-1) Mounting Sub-clause 4.31 Substrate material: Epoxide woven glass Test substrate: Figure-4 Bound strength of the end Sub-clause 4.33 face plating Bent value: 3 mm (3216 size max.) 1 mm (5025 size min.) Resistance Final measurements Sub-clause 4.33.6 Visual examination Resistance to soldering heat Sub-clause 4.18 Solder temperature: 260 C 5 C Immersion time: 10 s 0.5 s Visual examination Test items /9 5/12 Performance requirements R (1%+0.05) No visible damage As in 4.18.3.4 No sign of damage such as cracks. R (1%+0.05) Resistance solvent Sub-clause 4.29 Solvent: 2-propanol Solvent temperature: 23 C 5 C Method 2 Recovery: 48 h No visible damage Visual examination R (1%+0.05) Resistance Mounting Sub-clause 4.31 Substrate material: Epoxide woven glass Test substrate: Figure-3 Adhesion Sub-clause 4.32 Force: 5 N Duration: 10 s 1 s No visible damage Visual examination Rapid change temperature Sub-clause 4.19 Lower category temperature: -55 C Upper category temperature: +125 C Duration of exposure at each temperature: 30 min. Number of cycles: 5 cycles. No visible damage Visual examination R (1%+0.05) Resistance Component resistance 8 Product specification contained in this specification are subject to change at any time without notice. If you have any questions or a Purchasing Specification for any quality agreement is necessary, please contact our sales staff. Issue: KAMAYA ELECTRIC CO., LTD. Research & Development Department HOKKAIDO Research center Last update: 2015.2.6 KMY Title: No 9 Drawing No: RVC-K-HTS-0001 FIXED THICK FILM CHIP RESISTORS; RECTANGULAR TYPE AND HIGH VOLTAGE RVC16,20,32,50,63 Page: Test items Climatic sequence -Dry heat -Damp heat, cycle (12+12hour cycle) First cycle -Cold -Damp heat, cycle (12+12hour cycle) Remaining cycle -D.C. load 10 Mounting Endurance at 70 C Table-4(3) Condition of test (JIS C 5201-1) Sub-clause 4.23 Sub-clause 4.23.2 Test temperature: +155 C Duration: 16 h Sub-clause 4.23.3 Test method: 2 Test temperature: 55 C [Severity(2)] Sub-clause 4.23.4 Test temperature -55 C Duration: 2h Sub-clause 4.23.6 Test method: 2 Test temperature: 55 C [Severity (2)] Number of cycles: 5 cycles Sub-clause 4.23.7 The applied voltage shall be the rated voltage or the limiting element voltage whichever is the smaller. Duration: 1 min. Visual examination Resistance Sub-clause 4.31 Substrate material: Epoxide woven glass (RVC63 may use Alumina substrate.) Test substrate: Figure-3 Sub-clause 4.25.1 Ambient temperature: 70 C 2 C Duration: 1000 h The voltage shall be applied in cycles of 1.5 h on and 0.5 h. The applied voltage shall be the rated voltage or the limiting element voltage whichever is the smaller. Examination at 48 h , 500 h and 1000 h: Visual examination Resistance /9 6/12 Performance requirements No visible damage R (5%+0.1) No visible damage R (5%+0.1) Product specification contained in this specification are subject to change at any time without notice. If you have any questions or a Purchasing Specification for any quality agreement is necessary, please contact our sales staff. Issue: KAMAYA ELECTRIC CO., LTD. Research & Development Department HOKKAIDO Research center Last update: 2015.2.6 KMY Title: No 11 12 13 Drawing No: RVC-K-HTS-0001 FIXED THICK FILM CHIP RESISTORS; RECTANGULAR TYPE AND HIGH VOLTAGE RVC16,20,32,50,63 Page: /9 7/12 Table-4(4) Performance requirements Condition of test (JIS C 5201-1) Mounting Sub-clause 4.31 Substrate material: Epoxide woven glass Test substrate: Figure-3 Variation of resistance with Sub-clause 4.8 As in Table-1 temperature -55 C / +20 C +20 C / +155C Mounting Sub-clause 4.31 Substrate material: Epoxide woven glass Test substrate: Figure-3 Damp heat, steady state Sub-clause 4.24 Ambient temperature: 40 C 2 C Relative humidity : 93 +2 -3 % a) 1st group: without voltage applied. b) 2nd group: The d. c. voltage shall be applied continuously. The voltage shall be accordance with Sub-clause 4.24.2.1 b). without polarizing voltage [4.24.2.1, c)] No visible damage Visual examination Legible marking R (5%+0.1) Resistance Test items Dimensions (detail) Mounting Sub-clause 4.4.3 Sub-clause 4.31 Substrate material: Epoxide woven glass Test substrate: Figure-3 Endurance at upper category Sub-clause 4.25.3 temperature Ambient temperature:155 C 2 C Duration: 1000 h Examination at 48 h, 500 h and 1000 h: Visual examination Resistance As in Table-3 No visible damage R (5%+0.1) Product specification contained in this specification are subject to change at any time without notice. If you have any questions or a Purchasing Specification for any quality agreement is necessary, please contact our sales staff. Issue: KAMAYA ELECTRIC CO., LTD. Research & Development Department HOKKAIDO Research center Last update: 2015.2.6 KMY Drawing No: RVC-K-HTS-0001 FIXED THICK FILM CHIP RESISTORS; RECTANGULAR TYPE AND HIGH VOLTAGE RVC16,20,32,50,63 Page: Title: 8. Test substrate /9 8/12 c Unit: mm a :Copper clad b 40 :Solder resist d Style RVC50 RVC63 10.16 a 4.0 5.0 b 7.5 9.0 c 2.0 4.5 d 7.5 7.5 c 1.0 1.5 d 4.5 4.3 60.96 RVC50,63 TEST SUBSTRATE c Soldering land :Solder resist Style RVC16 RVC20 7.5 5.5 b 25 a 3.5 3 :Copper clad d Unit: mm 5.08 5.08 2.5 a 1.0 1.2 b 3.6 4.0 3 58.5 RVC16,20 TEST SUBSTRATE Soldering land Unit: mm :Copper clad :Solder resist 2.5 7.5 5 30 5 4 3.5 2 2.5 2.5 8 1.5 1.5 2 2 2 4 2.5 49 RVC32 TEST SUBSTRATE Figure-3 Remark 1). Material: Epoxide woven glass Thickness: 1.6mm Thickness of copper clad: 0.035mm 2). In the case of connection by connector, the connecting terminals are gold plated. However, the plating is not necessary when the connection is made by soldering. Product specification contained in this specification are subject to change at any time without notice. If you have any questions or a Purchasing Specification for any quality agreement is necessary, please contact our sales staff. Issue: KAMAYA ELECTRIC CO., LTD. Research & Development Department HOKKAIDO Research center Last update: 2015.2.6 KMY Title: Drawing No: RVC-K-HTS-0001 FIXED THICK FILM CHIP RESISTORS; RECTANGULAR TYPE AND HIGH VOLTAGE RVC16,20,32,50,63 Page: /9 9/12 Unit: mm :Copper clad c 1 a 40 :Solder resist Style RVC50 RVC20 b a 4.0 5.0 b 7.5 9.0 c 3.0 4.0 100 RVC50,63 BOUND STRENGTH OF THE END FACE PLATING TEST SUBSTRATE Unit: mm a :Copper clad 1 4.5 :Solder resist 40 d c d Style RVC16 RVC20 RVC32 b 70 100 a 1.0 1.2 2.5 b 3.6 4.0 5.0 c 1.20 1.65 2.0 d 3.0 3.0 2.5 Soldering land Remark 1). Material: Epoxide woven glass Thickness: 1.6mm Thickness of copper clad: 0.035mm RVC16,20,32 BOUND STRENGTH OF THE END FACE PLATING TEST SUBSTRATE Figure-4 Insulation plate Metal block measurement Point A Metal plate R0.25R0.5mm Measurement point B Insulation surface Component Pressure by spring (10.2N) Figure-5 Product specification contained in this specification are subject to change at any time without notice. If you have any questions or a Purchasing Specification for any quality agreement is necessary, please contact our sales staff. Issue: KAMAYA ELECTRIC CO., LTD. Research & Development Department HOKKAIDO Research center Last update: 2015.2.6 KMY Title: Drawing No: RVC-K-HTS-0001 FIXED THICK FILM CHIP RESISTORS; RECTANGULAR TYPE AND HIGH VOLTAGE RVC16,20,32,50,63 Page: /9 10/12 9. Taping 9.1 Applicable documents JIS C 0806-3: 1999, EIAJ ET-7200B: 2003 9.2 Taping dimensions 9.2.1 Paper taping (8mm width, 4mm pitches) Taping dimensions shall be in accordance with Figure-6 and Table-5. Unit: mm 40.1 t 1.5 Sprocket hole 1 +0.1 0 20.05 1.750.1 B 80.2 A t Carrier cavity 2 40.1 3.50.05 Direction of unreeling Style RVC16 RVC20 RVC32 Figure-6 Table-5 A B 1.150.15 1.90.2 1.650.15 2.50.2 2.000.15 3.60.2 t1 0.60.1 Unit: mm t2 0.8max. 0.80.1 1.0max. 9.2.2 Embossed taping dimensions shall be in accordance with Figure-7 and Table-6. Unit: mm 0.3 max. 20.05 Sprocket hole 1.5+0.1 0 1.750.1 40.1 Carrier cavity t1 Style RVC50 RVC63 A 3.10.2 3.60.2 W B E A 40.1 Direction of unreeling Figure-7 Table-6 B W 5.50.2 12.00.3 6.90.2 E 5.50.05 Unit: mm t1 1.10.15 Product specification contained in this specification are subject to change at any time without notice. If you have any questions or a Purchasing Specification for any quality agreement is necessary, please contact our sales staff. Issue: KAMAYA ELECTRIC CO., LTD. Research & Development Department HOKKAIDO Research center Last update: 2015.2.6 KMY Title: Drawing No: RVC-K-HTS-0001 FIXED THICK FILM CHIP RESISTORS; RECTANGULAR TYPE AND HIGH VOLTAGE RVC16,20,32,50,63 Page: /9 11/12 1). The cover tapes shall not cover the sprocket holes. 2). Tapes in adjacent layers shall not stick together in the packing. 3). Components shall not stick to the carrier tape or to the cover tape. 4). Pitch tolerance over any 10 pitches 0.2mm. 5). The peel strength of the top cover tape shall be with in 0.1N to 0.5N on the test method as shown in the following RVC16,20,32: Figure-8, RVC50,63: Figure-9. 6). When the tape is bent with the minimum radius for RVC16,20,32: 25 mm, or RVC50,63: 30 mm, the tape shall not be damaged and the components shall maintain their position and orientation in the tape. 7). In no case shall there be two or more consecutive components missing. The maximum number of missing components shall be one or 0.1%, whichever is greater. 8). The resistors shall be faced to upward at the over coating side in the carrier cavity. Top cover tape Carrier tape 165to180 Peel-off ( About 300mm/ min) Direction of unreeling Figure-8 Top cover tape Carrier tape 165to180 Peel-off ( About 300mm/ min) Direction of unreeling Figure-9 Product specification contained in this specification are subject to change at any time without notice. If you have any questions or a Purchasing Specification for any quality agreement is necessary, please contact our sales staff. Issue: KAMAYA ELECTRIC CO., LTD. Research & Development Department HOKKAIDO Research center Last update: 2015.2.6 KMY Title: Drawing No: RVC-K-HTS-0001 FIXED THICK FILM CHIP RESISTORS; RECTANGULAR TYPE AND HIGH VOLTAGE RVC16,20,32,50,63 Page: /9 12/12 9.3 Reel dimension Reel dimensions shall be in accordance with the following Figure-10 and Table-7. Plastic reel (Based on EIAJ ET-7200B) Unit: mm 0 +1 60 0 130.2 20.5 180 -1.5 Marking A 210.8 Marking B A B Figure-10 Table-7 Unit: mm A B Note Style Injection molding 11.41.0 RVC16,20,32 9 +1.0 0 131.0 Vacuum forming RVC50,63 171.0 Vacuum forming 13 +1.0 0 Note: Marking label shall be marked on a place of Marking A or two place of marking A and B. 9.4 Leader and trailer tape. (Example) 400mm min. 100mm min. 160mm min. End Start Trailer Leader Direction of unreeling Figure-11 10. Marking on package The label of a minimum package shall be legibly marked with follows. 10.1 Marking A (1) Classification (Style, Temperature coefficient of resistance, Rated resistance, Tolerance on rated resistance, Packaging form) (2) Quantity (3) Lot number (4) Manufacturer's name or trade mark 10.2 Marking B (KAMAYA Control label) (5) Others Product specification contained in this specification are subject to change at any time without notice. If you have any questions or a Purchasing Specification for any quality agreement is necessary, please contact our sales staff. Issue: KAMAYA ELECTRIC CO., LTD. Research & Development Department HOKKAIDO Research center Last update: 2015.2.6 Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Kamaya: RVC20K396JTP