Micrel, Inc. 5V/3.3V / 2 DIVIDER Precision Edge(R) SY10EP32V PrecisionSY100EP32V Edge(R) SY10EP32V SY100EP32V FEATURES Guaranteed maximum frequency > 4GHz 3.3V and 5V power supply options Guaranteed propagation delay <440ps over temperature Internal 75K input pull-down resistors Wide operating temperature range: -40C to +85C Available in 8-pin MSOP and SOIC packages ECL ProTM DESCRIPTION The SY10/100EP32V is an integrated /2 divider with differential clock inputs. The VBB pin, an internally generated voltage supply, is available to this device only. For single-ended input conditions, the unused differential input is connected to VBB as a switching reference voltage. VBB may also rebias AC-coupled inputs. When used, decouple VBB and VCC via a 0.01F capacitor and limit current sourcing or sinking to 0.5mA. When not used, VBB should be left open. The reset pin is asynchronous and is asserted on the rising edge. Upon power-up, the internal flip-flops will attain a random state; the reset allows for the synchronous use of multiple EP32's in a system. The 100k series includes internal temperature compensation circuitry. PIN NAMES Pin Function CLK, /CLK ECL Clock Inputs Reset ECL Asynchronous Reset VBB Reference Voltage Output Q, /Q ECL Data Outputs TRUTH TABLE(1) CLK /CLK RESET Q /Q X X Z L H Z /Z L F F Note 1: Z = LOW-to-HIGH Transition /Z = HIGH-to-LOW Transition F = Divide by 2 function. ECL Pro is a trademarks of Micrel, Inc. Precision Edge is a registered trademarks of Micrel, Inc. M9999-111605 hbwhelp@micrel.com or (408) 955-1690 Rev.: D 1 Amendment: /0 Issue Date: September 2005 Precision Edge(R) SY10EP32V SY100EP32V Micrel, Inc. PACKAGE/ORDERING INFORMATION Ordering Information(1) Package Type Operating Range Package Marking Lead Finish SY10EP32VZC Z8-1 Commercial HEP32V Sn-Pb SY10EP32VZCTR(2) Z8-1 Commercial HEP32V Sn-Pb SY100EP32VZC Z8-1 Commercial XEP32V Sn-Pb SY100EP32VZCTR(2) Z8-1 Commercial XEP32V Sn-Pb SY10EP32VKC K8-1 Commercial HP32 Sn-Pb SY10EP32VKCTR(2) K8-1 Commercial HP32 Sn-Pb SY100EP32VKC K8-1 Commercial XP32 Sn-Pb SY100EP32VKCTR(2) K8-1 Commercial XP32 Sn-Pb SY10EP32VZI Z8-1 Industrial HEP32V Sn-Pb SY10EP32VZITR(2) Z8-1 Industrial HEP32V Sn-Pb SY100EP32VZI Z8-1 Industrial XEP32V Sn-Pb SY100EP32VZITR(2) Z8-1 Industrial XEP32V Sn-Pb SY10EP32VKI K8-1 Industrial HP32 Sn-Pb SY10EP32VKITR(2) K8-1 Industrial HP32 Sn-Pb SY100EP32VKI K8-1 Industrial XP32 Sn-Pb SY100EP32VKITR(2) K8-1 Industrial XP32 Sn-Pb SY10EP32VZG(3) Z8-1 Industrial HEP32V with NiPdAu Pb-Free bar-line indicator Pb-Free SY10EP32VZGTR(2, 3) Z8-1 Industrial HEP32V with NiPdAu Pb-Free bar-line indicator Pb-Free SY100EP32VZG(3) Z8-1 Industrial XEP32V with NiPdAu Pb-Free bar-line indicator Pb-Free SY100EP32VZGTR(2, 3) Z8-1 Industrial XEP32V with NiPdAu Pb-Free bar-line indicator Pb-Free SY10EP32VKG(3) K8-1 Industrial HP32 with NiPdAu Pb-Free bar-line indicator Pb-Free SY10EP32VKGTR(2, 3) K8-1 Industrial HP32 with NiPdAu Pb-Free bar-line indicator Pb-Free SY100EP32VKG(3) K8-1 Industrial XP32 with NiPdAu Pb-Free bar-line indicator Pb-Free SY100EP32VKGTR(2, 3) K8-1 Industrial XP32 with NiPdAu Pb-Free bar-line indicator Pb-Free 8 VCC Part Number 7 Q 3 6 /Q 4 5 VEE Reset 1 CLK 2 /CLK VBB R /2 8-Pin SOIC (Z8-1) 8-Pin MSOP (K8-1) Notes: 1. Contact factory for die availability. Dice are guaranteed at TA = 25C, DC Electricals only. 2. Tape and Reel. 3. Pb-Free package is recommended for new designs. M9999-111605 hbwhelp@micrel.com or (408) 955-1690 2 Precision Edge(R) SY10EP32V SY100EP32V Micrel, Inc. ABSOLUTE MAXIMUM RATINGS(1) Symbol Rating Value Unit +6.0 V -6.0 to 0 +6.0 to 0 V V 50 100 mA 0.5 mA VCC -- VEE Power Supply Voltage VIN Input Voltage (VCC = 0V, VIN not more negative than VEE) Input Voltage (VEE = 0V, VIN not more positive than VCC) IOUT Output Current IBB VBB Sink/Source Current(2) TA Operating Temperature Range -40 to +85 C TSTORE Storage Temperature Range -65 to +150 C TLEAD Lead Temperature (soldering, 20 sec.) +260 C JA Package Thermal Resistance (Junction-to-Ambient) -Still Air SOIC -Still Air MSOP -multi-layer PCB 160 206 C/W C/W JC Package Thermal Resistance (Junction-to-Case) SOIC MSOP 39 39 C/W C/W -Continuous -Surge Note 1. Permanent device damage may occur if absolute maximum ratings are exceeded. This is a stress rating only and functional operation is not implied at conditions other than those detailed in the operational sections of this data sheet. Exposure to absolute maximum ratlng conditions for extended periods may affect device reliability. Note 2. Due to the limited drive capability, the VBB reference should only be used for inputs from the same packge device (i.e., do not sue for other devices). (10EP) LVPECL DC ELECTRICAL CHARACTERISTICS(1) VCC = 3.3V 10%; VEE = 0V(2) TA = -40C Symbol Parameter TA = +25C TA = +85C Min. Typ. Max. Min. Typ. Max. Min. Typ. Max. Unit -- 30 37 -- 30 37 -- 30 37 mA Output HIGH Voltage(3) 2165 2290 2415 2230 2355 2480 2290 2415 2540 mV VOL Output LOW Voltage(3) 1365 1490 1615 1430 1555 1680 1490 1615 1740 mV VIH Input HIGH Voltage (Single-Ended) 2090 -- 2415 2155 -- 2480 2215 -- 2540 mV VIL Input LOW Voltage (Single-Ended) 1365 -- 1690 1430 -- 1755 1490 -- 1815 mV VBB Output Voltage 1790 1890 1990 1855 1955 2055 1915 2015 2115 mV VIHCMR Input HIGH Voltage(4) Common Mode Range (Differential) 2.0 -- VCC 2.0 -- VCC 2.0 -- VCC V IIH Input HIGH Current -- -- 150 -- -- 150 -- -- 150 A IIL Input LOW Current 0.5 -150 -- -- -- -- 0.5 -150 -- -- -- -- 0.5 -150 -- -- -- -- A IEE Power Supply Current VOH CLK /CLK Note 1. 10EP circuits are designed to meet the DC specifications shown in the above table after thermal equilibrium has been established. The circuit is in a test socket or mounted on a printed circuit board and traverse airflow greater than 500lfpm is maintained. Note 2. Input and output parameters vary 1:1 with VCC. Note 3. All loading with 50 to VCC -2.0V. Note 4. The VIHCMR range is referenced to the most positive side of the differential input signal. M9999-111605 hbwhelp@micrel.com or (408) 955-1690 3 Precision Edge(R) SY10EP32V SY100EP32V Micrel, Inc. (10EP) PECL DC ELECTRICAL CHARACTERISTICS(1) VCC = 5.0V 10%; VEE = 0V(2) TA = -40C Symbol IEE Parameter Power Supply Current TA = +25C TA = +85C Min. Typ. Max. Min. Typ. Max. Min. Typ. Max. Unit -- -- 37 -- 30 37 -- -- 37 mA Output HIGH Voltage(3) 3865 3990 4115 3930 4055 4180 3990 4115 4240 mV VOL Output LOW Voltage(3) 3065 3190 3315 3130 3255 3380 3190 3315 3440 mV VIH Input HIGH Voltage (Single-Ended) 3790 -- 4115 3855 -- 4180 3915 -- 4240 mV VIL Input LOW Voltage (Single-Ended) 3065 -- 3390 3130 -- 3455 3190 -- 3515 mV VBB Output Voltage 3490 3590 3690 3555 3655 3755 3615 3715 3815 mV Input HIGH Common Mode Range (Differential) 2.0 -- VCC 2.0 -- VCC 2.0 -- VCC V IIH Input HIGH Current -- -- 150 -- -- 150 -- -- 150 A IIL Input LOW Current 0.5 -150 -- -- -- -- 0.5 -150 -- -- -- -- 0.5 -150 -- -- -- -- A VOH Voltage(4) VIHCMR CLK /CLK Note 1. 10EP circuits are designed to meet the DC specifications shown in the above table after thermal equilibrium has been established. The circuit is in a test socket or mounted on a printed circuit board and traverse airflow greater than 500lfpm is maintained. Note 2. Input and output parameters vary 1:1 with VCC. Note 3. All loading with 50 to VCC -2.0V. Note 4. The VIHCMR range is referenced to the most positive side of the differential input signal. (10EP) ECL/LVECL DC ELECTRICAL CHARACTERISTICS(1) VCC = 0V; VEE = -3.3V to 5.0V 10%(2) TA = -40C Symbol IEE Parameter TA = +85C Min. Typ. Max. Min. Typ. Max. Min. Typ. Max. Unit -- -- 37 -- 30 37 -- -- 37 mA Output HIGH Voltage(3) -1135 -1010 -885 -1070 -945 -820 -1010 -885 -760 mV VOL Output LOW Voltage(3) -1935 -1810 -1685 -1870 -1745 -1620 -1810 -1685 -1560 mV VIH Input HIGH Voltage (Single-Ended) -1210 -- -885 -1145 -- -820 -1085 -- -760 mV VIL Input LOW Voltage (Single-Ended) -1935 -- -1610 -1870 -- -1545 -1810 -- -1485 mV VBB Output Voltage -1510 -1410 -1310 -1445 -1345 -1245 -1385 -1285 -1185 mV 0.0 V VOH VIHCMR Power Supply Current TA = +25C Voltage(4) Input HIGH Common Mode Range (Differential) IIH Input HIGH Current IIL Input LOW Current VEE +2.0 CLK /CLK 0.0 VEE +2.0 0.0 VEE +2.0 -- -- 150 -- -- 150 -- -- 150 A 0.5 -150 -- -- -- -- 0.5 -150 -- -- -- -- 0.5 -150 -- -- -- -- A Note 1. 10EP circuits are designed to meet the DC specifications shown in the above table after thermal equilibrium has been established. The circuit is in a test socket or mounted on a printed circuit board and traverse airflow greater than 500lfpm is maintained. Note 2. Input and output parameters vary 1:1 with VCC. Note 3. All loading with 50 to VCC - 2.0V. Note 4. VIHCMR (min) varies 1:1 with VEE. The VIHCMR range is referenced to the most positive side of the differential input signal. M9999-111605 hbwhelp@micrel.com or (408) 955-1690 4 Precision Edge(R) SY10EP32V SY100EP32V Micrel, Inc. (100EP) LVPECL DC ELECTRICAL CHARACTERISTICS(1) VCC = +3.3V 10%; VEE = 0V(2) TA = -40C Symbol IEE Parameter Power Supply Current TA = +25C TA = +85C Min. Typ. Max. Min. Typ. Max. Min. Typ. Max. Unit -- -- 37 -- 30 37 -- -- 42 mA Output HIGH Voltage(3) 2155 2280 2405 2155 2280 2405 2155 2280 2405 mV VOL Output LOW Voltage(3) 1355 1480 1605 1355 1480 1605 1355 1480 1605 mV VIH Input HIGH Voltage (Single-Ended) 2075 -- 2420 2075 -- 2420 2075 -- 2420 mV VIL Input LOW Voltage (Single-Ended) 1355 -- 1675 1355 -- 1675 1355 -- 1675 mV VBB Output Voltage 1775 1875 1975 1775 1875 1975 1775 1875 1975 mV Input HIGH Common Mode Range (Differential) 2.0 -- VCC 2.0 -- VCC 2.0 -- VCC V IIH Input HIGH Current -- -- 150 -- -- 150 -- -- 150 A IIL Input LOW Current 0.5 -150 -- -- -- -- 0.5 -150 -- -- -- -- 0.5 -150 -- -- -- -- A VOH Voltage(4) VIHCMR CLK /CLK Note 1. 100EP circuits are designed to meet the DC specifications shown in the above table after thermal equilibrium has been established. The circuit is in a test socket or mounted on a printed circuit board and traverse airflow greater than 500lfpm is maintained. Note 2. Input and output parameters vary 1:1 with VCC. Note 3. All loading with 50 to VCC -2.0V. Note 4. The VIHCMR range is referenced to the most positive side of the differential input signal. (100EP) PECL DC ELECTRICAL CHARACTERISTICS(1) VCC = +5.0V 10%; VEE = 0V(2) TA = -40C Symbol IEE Parameter TA = +85C Min. Typ. Max. Min. Typ. Max. Min. Typ. Max. Unit -- -- 37 -- 30 37 -- -- 42 mA Output HIGH Voltage(3) 3855 3980 4105 3855 3980 4105 3855 3980 4105 mV VOL Output LOW Voltage(3) 3055 3180 3305 3055 3180 3305 3055 3180 3305 mV VIH Input HIGH Voltage (Single-Ended) 3775 -- 4120 3775 -- 4120 3775 -- 4120 mV VIL Input LOW Voltage (Single-Ended) 3055 -- 3375 3055 -- 3375 3055 -- 3375 mV VBB Output Voltage 3475 3575 3675 3475 3575 3675 3475 3575 3675 mV Input HIGH Common Mode Range (Differential) 2.0 -- VCC 2.0 -- VCC 2.0 -- VCC V IIH Input HIGH Current -- -- 150 -- -- 150 -- -- 150 A IIL Input LOW Current 0.5 -150 -- -- -- -- 0.5 -150 -- -- -- -- 0.5 -150 -- -- -- -- A VOH VIHCMR Power Supply Current TA = +25C Voltage(4) CLK /CLK Note 1. 100EP circuits are designed to meet the DC specifications shown in the above table after thermal equilibrium has been established. The circuit is in a test socket or mounted on a printed circuit board and traverse airflow greater than 500lfpm is maintained. Note 2. Input and output parameters vary 1:1 with VCC. Note 3. All loading with 50 to VCC -2.0V. Note 4. The VIHCMR range is referenced to the most positive side of the differential input signal. M9999-111605 hbwhelp@micrel.com or (408) 955-1690 5 Precision Edge(R) SY10EP32V SY100EP32V Micrel, Inc. (100EP) ECL/LVECL DC ELECTRICAL CHARACTERISTICS(1) VCC = 0V; VEE = -3.3V to -5.0V 10%(2) TA = -40C Symbol IEE Parameter TA = +85C Min. Typ. Max. Min. Typ. Max. Min. Typ. Max. Unit -- -- 37 -- 30 37 -- -- 42 mA Output HIGH Voltage(3) -1145 -1020 -895 -1145 -1020 -895 -1145 -1020 -895 mV VOL Output LOW Voltage(3) -1945 -1820 -1695 -1945 -1820 -1695 -1945 -1820 -1695 mV VIH Input HIGH Voltage (Single-Ended) -1225 -- -880 -1225 -- -880 -1225 -- -880 mV VIL Input LOW Voltage (Single-Ended) -1945 -- -1625 -1945 -- -1625 -1945 -- -1625 mV VBB Output Voltage -1525 -1425 -1325 -1525 -1425 -1325 -1525 -1425 -1325 mV 0.0 V VOH VIHCMR Power Supply Current TA = +25C Voltage(4) Input HIGH Common Mode Range (Differential) IIH Input HIGH Current IIL Input LOW Current VEE +2.0 CLK /CLK 0.0 VEE +2.0 0.0 VEE +2.0 -- -- 150 -- -- 150 -- -- 150 A 0.5 -150 -- -- -- -- 0.5 -150 -- -- -- -- 0.5 -150 -- -- -- -- A Note 1. 100EP circuits are designed to meet the DC specifications shown in the above table after thermal equilibrium has been established. The circuit is in a test socket or mounted on a printed circuit board and traverse airflow greater than 500lfpm is maintained. Note 2. Input and output parameters vary 1:1 with VCC. Note 3. All loading with 50 to VCC -2.0V. Note 4. VIHCMR (min) varies 1:1 with VEE. The VIHCMR range is referenced to the most positive side of the differential input signal. TIMING DIAGRAM CLK t RR RESET Q M9999-111605 hbwhelp@micrel.com or (408) 955-1690 6 Precision Edge(R) SY10EP32V SY100EP32V Micrel, Inc. AC ELECTRICAL CHARACTERISTICS(1) NECL: VCC = 0V, VEE = -3.3V to -5.0V 10%; PECL: VEE = 0V, VCC = +3.3V to +5.0V 10% TA = -40C Symbol Parameter Frequency(3) TA = +25C TA = +85C Min. Typ. Max. Min. Typ. Max. Min. Typ. Max. Unit 4 -- -- 4 -- -- 4 -- -- GHz fMAX Maximum tPLH tPHL Propagation Delay to Output Differential RESET, CLK Q, /Q 250 330 420 260 275 430 280 400 440 tRR Set/Reset Recovery 200 -- -- 200 100 -- 200 -- -- ps tPW Minimum Pulse Width RESET 550 -- -- 550 200 -- 550 -- -- ps -- 0.2 <1 -- 0.2 <1 -- 0.2 <1 ps(rms) Jitter(2) ps tJITTER Cycle-to-Cycle RMS VPP Input Voltage Swing (Differential) 150 800 1200 150 800 1200 150 800 1200 mV tr tf Output Rise/Fall Times Q, /Q (20% to 80%) 50 100 150 50 100 160 50 100 160 ps Note 1. Measured using a 750mV source, 50% duty cycle clock source. All loading with 50 to VCC -2.0V. Note 2. See Figure 1. fMAX Jitter below. Note 3. fMAX guaranteed for functionality only. VOL and VOH levels are guaranteed at DC only. fMAX Jitter 900 9 800 8 Measured 7 600 6 500 Simulated 5 400 4 300 3 200 2 100 0 (Jitter) 0 ps (RMS) VOLTAGE (mV) 700 1 0 1000 2000 3000 4000 5000 6000 FREQUENCY (MHz) Figure 1. fMAX and RMS Jitter M9999-111605 hbwhelp@micrel.com or (408) 955-1690 7 Precision Edge(R) SY10EP32V SY100EP32V Micrel, Inc. 8 LEAD MSOP (K8-1) Rev. 01 M9999-111605 hbwhelp@micrel.com or (408) 955-1690 8 Precision Edge(R) SY10EP32V SY100EP32V Micrel, Inc. 8 LEAD SOIC .150" WIDE (Z8-1) Rev. 03 MICREL, INC. 2180 FORTUNE DRIVE SAN JOSE, CA 95131 TEL + 1 (408) 944-0800 FAX + 1 (408) 474-1000 WEB USA http://www.micrel.com The information furnished by Micrel in this datasheet is believed to be accurate and reliable. However, no responsibility is assumed by Micrel for its use. Micrel reserves the right to change circuitry and specifications at any time without notification to the customer. Micrel Products are not designed or authorized for use as components in life support appliances, devices or systems where malfunction of a product can reasonably be expected to result in personal injury. Life support devices or systems are devices or systems that (a) are intended for surgical implant into the body or (b) support or sustain life, and whose failure to perform can be reasonably expected to result in a significant injury to the user. A Purchaser's use or sale of Micrel Products for use in life support appliances, devices or systems is at Purchaser's own risk and Purchaser agrees to fully indemnify Micrel for any damages resulting from such use or sale. (c) 2005 Micrel, Incorporated. M9999-111605 hbwhelp@micrel.com or (408) 955-1690 9