MVAD040-12 - MURATA MANUFACTURING

MVAD040 Series

40W 2" x 4" AC-DC Power Supply Converter

MVAD040.B01 Page 1 of 6

www.murata-ps.com/support

For full details go to

www.murata-ps.com/rohs

www.murata-ps.com

FEATURES

 ITE (2nd Ed.) and Medical (3rd ed.) MOPP safety

approved

 30-40W compact high density

 2" x 4" standard footprint

 High efﬁ ciency up to 89%

 Universal AC input

 Low proﬁ le - 1U package

 Convection-cooled operation up to 40W

 Complies with 5000m altitude

 RoHS compliant

 UL Class I and II approved

 Less than 0.3W no load input power

 Complies with ErP/Energy Star requirement

average efﬁciency>85.3% (24V and 48V)

ORDERING GUIDE

Model Number Natural Convection Cooling Main Output (V1)

MVAD040-05 30W 5V

MVAD040-12

40W

12V

MVAD040-24 24V

MVAD040-48 48V

INPUT CHARACTERISTICS

Parameter Conditions Min. Typ. Max. Units

Input Voltage Operating Range Single phase 90 120/230 264 Vac

DC 120 300 Vdc

Input Frequency 47 50/60 63 Hz

Turn-on Input Voltage Input rising at full load 50 70 Vac

Turn-off Input Voltage Input falling at full load 50 70

Input Current 90Vac input, full load 0.9 A

Inrush Current At 264Vac, at 25°C cold

start 60 Apk

OUTPUT CHARACTERISTICS

Model Number Main Output

Voltage (V1) Load Current Peak Load3Load Capacitance Line, Load, Cross

Regulation

Typical Efﬁ ciency

@230Vac full load

MVAD040-05 5V 0 to 6A 0 to 1200μF ± 2% 80%

MVAD040-12 12V 0 to 3.34A 5.0A 0 to 680μF ± 2% 87%

MVAD040-24 24V 0 to 1.67A 2.5A 0 to 330μF ± 2% 88%

MVAD040-48 48V 0 to 0.84A 1.25A 0 to 220μF ± 2% 89%

Main Output Characteristics (all models)

Parameter Conditions Min. Max. Units

Transient Response (MVAD040-05 only) 50% load step, 1A/μsec slew rate ± 8 %

Transient Response (all other models) ± 5

Settling Time to 1% of Nominal 200 μsec

Turn On Delay After application of input power 1 sec

Output Voltage Rise Monotonic, 0 to 100% load 50 msec

Setpoint Accuracy 120Vac, 40W, 25°C ± 0.5 %

Output Holdup, MVAD040-05 only 115Vac, 100% load 20 msec

Output Holdup, all other models 115Vac, 100% load 15 msec

Temperature Coefﬁ cient 0.02 %/°C

Ripple Voltage & Noise11%

1. Ripple and noise are measured with 0.1 μF of ceramic capacitance and 47 μF of electrolytic capacitance on

each of the power supply outputs. The output noise requirements apply over a 0 Hz to 20 MHz bandwidth. A

short coaxial cable with 50ohm scope termination is used.

2. Unless otherwise speciﬁ ed all readings are taken at 120Vac input and 25 °C ambient temperature.

3. Peak current lasting <15 seconds with a maximum 10% duty cycle and with an average output power of 40W.

www.murata-

s.com/en/3d/acdc.htm

www.murata-ps.com/en/3d/acdc.htm

www.murata-ps.com

acdc.htm

www.murata-

s.com/en/3d/acdc.htm

www.murata-ps.com

acdc.htm

www.murata-

s.com/en/3d/acdc.htm

Available now at

www.murata-ps.com/en/3d/acdc.html

Test Certiﬁ cate

and Test Report

DESCRIPTION

The MVAD040 series switching power supplies utilize advanced component and circuit technologies

to deliver high efﬁ ciency. Designed for Medical, Telecom, and Industrial applications to satisfy 1U

height design considerations, the MVAD040 Series measures only 2.0" x 4.0" x 1.3". All models offer

universal AC input and compliance to worldwide safety and EMC standards.

MVAD040 Series

40W 2" x 4" AC-DC Power Supply Converter

MVAD040.B01 Page 2 of 6

www.murata-ps.com/support

ENVIRONMENTAL CHARACTERISTICS

Parameter Conditions Min. Typ. Max. Units

Storage Temperature Range -40 85

°C

Operating Temperature Range See thermal derating curves -20 70

Start up -20

Operating Humidity Non-condensing 10 95 %

Operating Altitude For Class I ITE Equipment deployment -200 5000 m

Other -200 2000

MTBF Telcordia SR-332 M1C3 25°C 1M Hours

Shock

Operating, IEC60068-2-27, half-sine 5G, 6ms,

3 times per face, 6 faces Complies

Non-operating, IEC60068-2-27, half-sine,

30G, 18ms, 3 times per face, 6 faces Complies

Vibration

Operating, IEC60068-2-6, 1.0G, 10-150Hz,

10minutes per axis, on all 3 axes Complies

Non-operating, IEC60068-2-6, 2.0G,

10-150Hz, 10minutes per axis, on all 3 axes Complies

Safety

IEC60950-1:2005 (2nd Edition); Am1:2009

UL60950-1 2nd Edition,2011-12-19, CSA C22.2 No. 60950-1-07, 2nd Edition,2011-12

EN60950-1:2006 + A11:2009 + A1:2010 + A12:2011

IEC60601-1:2005 + CORR.1(2006) + CORR.2(2007)

ANSI/AAMI ES60601-1 (2005+C1:09 + A2:10), CSA-C22.2 No. 60601-1(2008), MOPP

CE Marking per LVD

Warranty 2 years

Outside Dimensions 2.0" x 4.0" x 1.3" (50.8mm x 101.6mm x 33.02mm)

Weight 0.28lbs (127g) typical (MVAD040-05 only)

0.27lbs (123g) typical (all other models)

PROTECTION CHARACTERISTICS

Parameter Conditions Min. Typ. Max. Units

Overvoltage Protection Latching (60% load) 110 160 %V1

Overcurrent Protection, MVAD040-05 only Hiccup mode 110 160 %A

Overcurrent Protection, all other models Hiccup mode 170 240 %A

ISOLATION CHARACTERISTICS

Parameter Conditions Min. Typ. Max. Units

Isolation

Primary to Earth Ground (1xMOPP) 1500 Vac

Primary to Secondary (2xMOPP)4 4000

Secondary to Earth Ground 500 Vdc

Leakage Current (under normal conditions) 240Vac, 60Hz, 25°C 300

μA264Vac, 60Hz, 25°C 350

Touch Current 264Vac, 60Hz, 25°C 100

EMISSIONS AND IMMUNITY

Characteristic Standard Compliance

Input Current Harmonics IEC/EN 61000-3-2 Class A

Voltage Fluctuation and Flicker IEC/EN 61000-3-3 Complies

Conducted Emissions EN 55022 Class B, Class A (at Class II equipment)

FCC Part 15 Class B, Class A (at Class II equipment)

ESD Immunity IEC/EN 61000-4-2 Level 4, Criterion A

Radiated Field Immunity IEC/EN 61000-4-3 Level 2, Criterion A

Electrical Fast Transient Immunity IEC/EN 61000-4-4 Level 3, Criterion A

Surge Immunity IEC/EN 61000-4-5 Level 4, Criterion A

RF Conducted Immunity IEC/EN 61000-4-6 Level 2, Criterion A

Magnetic Field Immunity IEC/EN 61000-4-8 Level 2, Criterion A

Voltage dips, interruptions IEC/EN 61000-4-11 Level 3, Criterion B

4. At class I equipment.

MVAD040 Series

40W 2" x 4" AC-DC Power Supply Converter

MVAD040.B01 Page 3 of 6

www.murata-ps.com/support

Inrush waveform (AC264V 25°C)

EMI CONSIDERATIONS

For optimum EMI performance, the power supply should be mounted to a metal plate grounded to all 4 mounting holes of the power supply. To comply with

safety standards, this plate must be properly grounded to protective earth (see mechanical dimension notes). Pre-compliance testing has shown the stand-

alone power supply to comply with EN55022 class A radiated emissions. Radiated emission results vary with system enclosure and cable routing paths.

EMI CONSIDERATIONS

For optimum EMI performance, the power supply should be mounted to a metal plate grounded to all 4 mounting holes of the power supply. To comply with

safety standards, this plate must be properly grounded to protective earth (see mechanical dimension notes). Pre-compliance testing has shown the stand-

alone power supply to comply with EN55022 class A radiated emissions. Radiated emission results vary with system enclosure and cable routing paths.

SAFETY CONSIDERATIONS

1. This power supply is a component level power supply intended for use in class I or class II applications. Secondary ground traces need to be suit-

ably isolated from primary ground traces when used in class II applications.

2. When the power supply is used in class II equipment, all ground traces and components connected to the primary side are considered primary for

spacing and insulation considerations.

3. Double pole/neutral fusing.

PERFORMANCE DATA

0 0.5 1 1.5 2 2.5 3 3.5

Output current (A)

AC90V

AC115V

AC230V

AC264V

MVAD040-12 Eĸciency (%)

0123456

MVAD040-05 Eĸciency (%)

Output current (A)

AC90V

AC115V

AC230V

AC264V

0.0 0.2 0.4 0.6 0.8 1.0

AC90V

AC115V

AC230V

AC264V

MVAD040-48 Eĸciency (%)

Output current (A)

0 0.3 0.6 0.9 1.2 1.5 1.8

AC90V

AC115V

AC230V

AC264V

MVAD040-24 Eĸciency (%)

Output current (A)

-20-10 0 1020304050607080

Output power (W)

Ambient temperature (°C)

MVAD040-12/24/48 Thermal DeraƟng

MVAD040-05 Thermal DeraƟng

MVAD040 Series

40W 2" x 4" AC-DC Power Supply Converter

MVAD040.B01 Page 4 of 6

www.murata-ps.com/support

MECHANICAL DIMENSIONS – MVAD040-05 ONLY

Dimensions: 2.0" x 4.0" x 1.3" (50.8mm x 101.6mm x 33.02mm)

INPUT/OUTPUT CONNECTOR AND SIGNAL SPECIFICATION AND MATING CONNECTORS

PIN Description Mating Housing Crimp terminal/pins

Input Connector CN1 : Molex 26-62-4030

Molex 09-50-8031 with locking ramp Molex 6838 Series

1 AC Line (V-)

3 AC Neutral (V+)

Spade Connector: #250

GND Earth Ground

Output Connector CN2 : Molex 26-60-4040

Molex 09-50-8041 with locking ramp Molex 6838 Series

1, 2 V1

3, 4 DC Return

All dimensions in inches (mm). tolerance is +/-0.02’ (0.5)

Mounting holes H1 and H2 should be earth-grounded for EMI purpose

Mounting holes H2 is earth ground connection

This power supply requires mounting on standoffs minimum 0.2' (5.0) in height

MVAD040 Series

40W 2" x 4" AC-DC Power Supply Converter

MVAD040.B01 Page 5 of 6

www.murata-ps.com/support

MECHANICAL DIMENSIONS – MVAD040-12 ONLY

Dimensions: 2.0" x 4.0" x 1.3" (50.8mm x 101.6mm x 33.02mm)

INPUT/OUTPUT CONNECTOR AND SIGNAL SPECIFICATION AND MATING CONNECTORS

PIN Description Mating Housing Crimp terminal/pins

Input Connector CN1 : Molex 26-62-4030

Molex 09-50-8031 with locking ramp Molex 6838 Series

1 AC Line (V-)

3 AC Neutral (V+)

Spade Connector: #250

GND Earth Ground

Output Connector CN2 : Molex 26-60-4040

Molex 09-50-8041 with locking ramp Molex 6838 Series

1, 2 V1

3, 4 DC Return

All dimensions in inches (mm). tolerance is +/-0.02’ (0.5)

Mounting holes H1 and H2 should be earth-grounded for EMI purpose

Mounting holes H2 is earth ground connection

This power supply requires mounting on standoffs minimum 0.2' (5.0) in height

MVAD040 Series

40W 2" x 4" AC-DC Power Supply Converter

MVAD040.B01 Page 6 of 6

www.murata-ps.com/support

Murata Power Solutions, Inc.

11 Cabot Boulevard, Mansﬁ eld, MA 02048-1151 U.S.A.

ISO 9001 and 14001 REGISTERED

This product is subject to the following operating require-

ments and the Life and Safety Critical Application Sales

Policy. Refer to: http://www.murata-ps.com/requirements/

Murata Power Solutions, Inc. (“Murata”) makes no representation that the use of its products in the circuits described herein, or the use of other technical information contained herein, will not infringe upon existing or future patent rights. The descriptions contained herein do not imply the

granting of licenses to make, use, or sell equipment constructed in accordance therewith. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards that anticipate dangerous consequences of failures, monitor failures and their consequences, lessen

the likelihood of failures that might cause harm, and take appropriate remedial actions. Buyer will fully indemnify Murata, its afﬁ liated companies, and its representatives against any damages arising out of the use of any Murata products in safety-critical applications. Speciﬁ cations are subject

MECHANICAL DIMENSIONS – MVAD040-xx 24V and 48V MODELS

Dimensions: 2.0" x 4.0" x 1.3" (50.8mm x 101.6mm x 33.02mm)

INPUT/OUTPUT CONNECTOR AND SIGNAL SPECIFICATION AND MATING CONNECTORS

PIN Description Mating Housing Crimp terminal/pins

Input Connector CN1 : Molex 26-62-4030

Molex 09-50-8031 with locking ramp Molex 6838 Series

1 AC Line (V-)

3 AC Neutral (V+)

Spade Connector: #250

GND Earth Ground

Output Connector CN2 : Molex 26-60-4040

Molex 09-50-8041 with locking ramp Molex 6838 Series

1, 2 V1

3, 4 DC Return

All dimensions in inches (mm). tolerance is +/-0.02’ (0.5)

Mounting holes H1 and H2 should be earth-grounded for EMI purpose

Mounting holes H2 is earth ground connection

This power supply requires mounting on standoffs minimum 0.2' (5.0) in height