© Copyright 2019 WIZnet Co., Ltd. All rights reserved.
WizFi360-EVB-Shield Datasheet
(Version 1.12)
http://www.wiznet.io
2 / 15 WizFi360-EVB-Shield Datasheet
Document Revision History
Date
Revision
Changes
2019-07-25
V1.0
Official Release
2019-09-20
V1.1
Added “Figure 3”, Figure 4” DIP SW On/Off State
Added “Figure 5”, Figure 6” DIP SW On/Off signal wiring
Added “Figure 8” - UART Selector Pin Header Example
2019-10-10
1.11
Added “3. Electrical Specifications”
Edited “6.1 DIP Switch Configurations
2019-10-18
1.12
Changed Board name
Edited “6.1 DIP Switch Configurations “SW2” – OFF”
WizFi360-EVB-Shield Datasheet 3 / 15
Table of Contents
1. Overview ................................................................................................................................................................... 4
2. Features .................................................................................................................................................................... 4
2.1. WizFi360 ...................................................................................................................................................... 4
2.2. ETC .................................................................................................................................................................. 5
3. Electrical Specifications .................................................................................................................................... 6
4. Block Diagram ....................................................................................................................................................... 6
5. Callout ........................................................................................................................................................................ 7
6. Board Configurations ........................................................................................................................................ 8
6.1. DIP Switch Configurations ................................................................................................................ 8
6.2. UART Selector Pin Header ............................................................................................................. 11
7. Schematic & Partlist ....................................................................................................................................... 12
8. Dimension ............................................................................................................................................................. 13
9. Important Notice .............................................................................................................................................. 14
4 / 15 WizFi360-EVB-Shield Datasheet
1. Overview
This document describes WizFi360-EVB-Shield. WizFi360-EVB-Shield is a development boa
rd for experiment, test and verification of WizFi360. WizFi360-EVB-Shield can also be use
d as an Arduino shield.
WizFi360 is a low cost and low-power consumption industrial-grade Wi-Fi module. It is
compatible with IEEE802.11 b/g/n standard and supports Soft-AP, Station and Soft-AP +
Station modes. The serial port baud rate can be up to 2Mbps, which can meet the requ
irement of various applications.
2. Features
2.1. WizFi360
Wi-Fi 2.4GHz 802.11 b/g/n
Support Station / Soft-AP / Soft-AP + Station operation modes
Support “Data pass-through” and “AT command data transfer” mode
Support serial AT command configuration
Support TCP Server / TCP Client / UDP operating mode
Support configuration of operating channel 0 ~ 13
Support auto 20MHz / 40MHz bandwidth
Support WPA_PSK / WPA2_PSK encryption
Serial port baud rate up from 600bps to 2Mbps with 16 common values
Support up to 5 TCP / UDP links
Obtaining IP address automatically from the DHCP server (Station mode)
DHCP service for Wireless LAN clients (AP mode)
Support DNS for communication with servers by domain name
Support “Keep-Alive” to monitor TCP connection
Support “Ping” for monitoring network status
Built-in SNTP client for receiving the network time
Support built-in unique MAC address and user configurable
WizFi360-EVB-Shield Datasheet 5 / 15
Support firmware upgrade by UART Download / OTA (via WLAN)
Industrial grade (operating temperature range: -40 ° C ~ 85 ° C)
CE, FCC, KC certification
2.2. ETC
Built-in UART to USB chip
CP2104-GM
Micro USB B Type Connector
UART Selector
JP1, JP2, JP3
2.54mm Pin Header
Built-in Sensors
Temperature/Humidity Sensor: DHT11
CDS Sensor: GL5537
Built-in Tact Switches
System Reset Switch: S1
Wi-Fi Reset Switch: S2
Built-in LED Indicators
D13 LED
Built-in Level Shifters
The voltage of the RXD/TXD signal changes according to the main board
platform voltage.
Built-in DIP Switches
UART RXD/TXD Selector: SW1
UART RTS/CTS Selector: SW2
Sensor/RESET Pins Selector: SW3
6 / 15 WizFi360-EVB-Shield Datasheet
3. Electrical Specifications
Parameters
Min
Typ
Max
Operation Voltage
4.5
5
5.5
Send IEEE802.11b, CCK 11Mbps, POUT = +19 dBm
-
230
290
Send IEEE802.11g, OFDM 54Mbps, POUT = +13.5 dBm
-
210
-
Send IEEE802.11n, OFDM MCS7, POUT = +12 dBm
-
210
-
Receive IEEE802.11 b/g/n
-
100
110
Standby Mode
-
135
-
Modem Sleep Mode
-
20
-
Light Sleep Mode
-
13
-
4. Block Diagram
WizFi360
USB to UartMicro USB
RXD/TXD
Select Switch
RTS/CTS
On/Off Switch
Sensor/Reset
On/Off Switch
RXD Pin Header
TXD Pin Header
D0~D7 Pin Header
CDS/DHT11
Sensor
Level Shifter
Arduino Pin Header
Arduino Pin Header
Figure 1. WizFi360-EVB-Shield Block Diagram
WizFi360-EVB-Shield Datasheet 7 / 15
5. Callout
WizFi360
Micro USB
WizFi360
Reset SW
Main
Reset SW
Sensor Pins
DIP SW
RXD/TXD Connect
Pin Header
RTS/CTS
DIP SW
RXD/TXD
DIP SW
Figure 2. Callout
8 / 15 WizFi360-EVB-Shield Datasheet
6. Board Configurations
6.1. DIP Switch Configurations
Figure 3. Off State
Figure 4. On State
SW1 RXD/TXD Selector DIP Switch
ON: RXD/TXD of WizFi360 connect to USB
WizFi360
Micro USB
USB to
UART
SW1
RXD/TXD DIP SW
If ON
RXD/TXD Connect
Pin Header
If SW1 is On, should
never use this pin header
Figure 5. If SW1 ON, signal wiring
WizFi360-EVB-Shield Datasheet 9 / 15
It is only possible to communicate with WizFi360 using USB.
If this DIP SW On, should never use RXD/TXD Pin Header
OFF: RXD/TXD of WizFi360 connect to JP1 and JP3
WizFi360
RXD/TXD Connect
Pin Header
SW1
RXD/TXD DIP SW
If OFF
UART Voltage
Figure 6. If SW1 OFF, signal wiring
UART Pin Header, Arduino PIN
If the jumper cap is not attached to the UART pin header, it will not be
connected to the Arduino pin.
UART output voltage is IOREF voltage.
IO voltage of MCU you use must be connected as IOREF.
Pin 1: RXD
Pin 2: TXD
SW2 RTS/CTS Selector DIP Switch
10 / 15 WizFi360-EVB-Shield Datasheet
ON: RTS/CTS of WizFi360 connect to D7 and D6
If the state of SW2 is ON, D7 and D6 of UART jumper cannot be used.
OFF: RTS/CTS of WizFi360 not connect to anywhere
Pin 1: RTS D7
Pin 2: CTS D6
SW3 Sensor/RESET Pins Selector DIP Switch
ON: Connect to Arduino Pin
OFF: Not connect to anywhere
Pin 1: A0 CDS
Pin 2: D14 DHT11
Pin 3: RESET
WizFi360-EVB-Shield Datasheet 11 / 15
6.2. UART Selector Pin Header
RXD
TXD
D0
D1
D2
D3
D4
D5
D6
D7
D8
JP1
JP3
JP2
Figure 7. UART Selector Pin Header
If state of SW1 is OFF, you can use this Pin Header. You can use the jumper cap to connect
the pin header to select the RXD / TXD pin for the Arduino.
JP1 WizFi360 RXD (Connected to all pins of JP1)
JP2 Arduino D0~D8 Pins
Ex) JP2-1pin connected D0, JP2-2pin connected D1… JP2-9pin connected D8
JP3 WizFi360 TXD (Connected to all pins of JP3)
EX) If you connect the jumper cap as shown in the Figure. 6, RXD is connected to D0,
TXD is connected to the D1.
12 / 15 WizFi360-EVB-Shield Datasheet
Jumpper
cap
Figure 8. UART Selector Pin Header Example
7. Schematic & Partlist
https://github.com/Wiznet/Hardware-Files-of-WIZnet/tree/master/07_WizFi_Module/WizFi360-EVB-
Shield
WizFi360-EVB-Shield Datasheet 13 / 15
8. Dimension
The dimension of WizFi360-EVB is the same as Arduino UNO.
Figure 9. Dimension
14 / 15 WizFi360-EVB-Shield Datasheet
9. Important Notice
WIZnet reserves the right to make corrections, modifications, enhancements, improvements
and other changes to its products and services at any time, and to discontinue any product
or service without notice. Customers should obtain the latest relevant information before
placing orders, and should verify that such information is current and complete. All products
are sold subject to WIZnet’s terms and conditions of sale, supplied at the time of order
acknowledgment. Information relating to device applications, and the like, is intended as
suggestion only and may be superseded by updates. It is the customers responsibility to
ensure that their application meets their own specifications. WIZnet makes no representation
and gives no warranty relating to advice, support or customer product design.
WIZnet assumes no responsibilities or liabilities for the use of any of its products, conveys no
license or title under any patent, copyright or mask work rights to these products, and makes
no representations or warranties that these products are free from patent, copyright or mask
work infringement, unless otherwise specified.
WIZnet products are not intended for use in life support systems/appliances or any systems
where product malfunction can reasonably be expected to result in personal injury, death,
severe property damage or environmental damage. WIZnet customers using or selling WIZnet
products for use in such applications do so at their own risk and agree to fully indemnify
WIZnet for any damages resulting from such use.
All trademarks are the property of their respective owners.
WizFi360-EVB-Shield Datasheet 15 / 15
Copyright Notice
Copyright 2019 WIZnet Co., Ltd. All Rights Reserved.
Technical Support: https://forum.wiznet.io/
Sales & Distribution: sales@wiznet.io
For more information, visit our website at http://www.wiznet.io/