F-219 (Rev 20AUG20) (R) HQDP-020-06.00-SEU-TTR-6-F (0.50 mm) .0197"(HQDP) (0.80 mm) .0315"(EQDP) HQDP, EQDP SERIES EQDP-028-06.00-STR-TTL-7-F Q PAIRS TWINAX CABLE ASSEMBLIES (R) EQDP Mates with: QTE-DP, QSE-DP HQDP Mates with: QTH-DP, QSH-DP SPECIFICATIONS For complete specifications see www.samtec.com?EQDP or www.samtec.com?HQDP Cable: 30 AWG twinax ribbon Signal Routing: 100 W Differential Cable Bending Radius: (3.18 mm) 1/8" min Plating: Au over 50 " (1.27 m) Ni Current Rating: EQDP = 500 mA per pin HQDP = 400 mA per pin (6 adjacent pins powered) Propagation Delay: 4.67 nsec/meter Operating Temp Range: -25 C to +105 C Skew (pair-to-pair): <10 ps/ft Skew (within a pair): <5 ps/ft EMI Performance: FCC Class A RoHS Compliant: Yes Surface Mount or Edge Mount HQDP or EQDP Rating based on Samtec reference channel. For full SI performance data visit Samtec.com or contact SIG@samtec.com NO. OF PAIRS TYPE For complete scope of recognitions see www.samtec.com/quality HQDP FILE NO. E111594 ALSO AVAILABLE * Pairs * Terminations 30 AWG twinax ribbon cable HIGH-SPEED CHANNEL PERFORMANCE RECOGNITIONS (MOV Required) Differential Pair routing -020, -040, -060 = (0.50 mm) .0197" pitch (20 pairs per bank) HQDP Series EQDP -014, -028, -042, -056 = (0.80 mm) .0315" pitch 14 G b p s WIRE LENGTH -"XX.XX" = Wire Length in Inches (43.7 mm) 01.72" minimum (14 pairs per bank) EQDP Series OAL = Wire Length + (20.32) .800 (3.81) .150 Wire Length (1.27) .050 Notes: Cable lengths longer than 40.00" (1 meter) are not supported with S.I. test data. Design your High-Speed Cable with Samtec's High-Speed Cable Solutionator(R) at www.samtec.com/hdr This Series is non-standard, non-returnable. END NO. 1 (-TEU SHOWN) END NO. 1 END NO. 2 Specify END ASSEMBLIES from chart WIRING OPTION SCREW OPTION -5 Leave blank for no Screw Option = Pin 1 to Pin 1 -6 = Pin 1 to Pin 2 END SURFACE MOUNT TTR Terminal, Top, Notch Right TTL Terminal, Top, Notch Left TBR Terminal, Bottom, Notch Right TBL Terminal, Bottom, Notch Left STR Socket, Top, Notch Right STL Socket, Top, Notch Left SBR Socket, Bottom, Notch Right SBL Socket, Bottom, Notch Left END END NO. 2 (-TTR SHOWN) Optional Captive Screw or Screw Mount Option Socket or Terminal TEU TED SEU SED EDGE MOUNT Terminal, Edge, Notch Up Terminal, Edge, Notch Down Socket, Edge, Notch Up Socket, Edge, Notch Down -7 = Pin 1 to Second Last Pin -8 = Pin 1 to Last Pin -S = End No. 2 -B = Both Ends WIRING REQUIREMENTS WIRING END OPTIONS OPTION TTR, TBL, STL, SBR, TEU, SED to TTR, TBL, STL, SBR, TED, SEU or 5 or 6 TTL, TBR, STR, SBL, TED, SEU to TTL, TBR, STR, SBL, TEU, SED TTR, TBL, STL, SBR, TEU, SED to TTL, TBR, STR, SBL, TEU, SED or 7 or 8 TTL, TBR, STR, SBL, TED, SEU to TTR, TBL, STL, SBR, TED, SEU Due to technical progress, all designs, specifications and components are subject to change without notice. WWW.SAMTEC.COM -F = End No. 1 All parts within this catalog are built to Samtec's specifications. Customer specific requirements must be approved by Samtec and identified in a Samtec customer-specific drawing to apply.