Product Specification SR42W001-PS-1.2 Page 1
Antennas for Wireless M2M Applications
®
1. Features
Antenna for 2.4 2.5 GHz and 4.9 5.9 GHz applications: Wi-Fi
802.11a/b/g/j/n/ac
Maintains high performance on device: DFI (Designed For Integration)
Ultra compact
SMD mounting
Supplied on Tape and Reel
2. Description
Mutica is intended for use with all dual-band Wi-Fi applications. Only requires a small
ground plane and integrates into the corner with minimal PCB clearance area.
Design centred on being part of the device and not designing the device around the
antenna (DFI - Designed for Integration). Ideal for single and MIMO antenna
systems.
3. Applications
Access Points
Portable Devices
Headsets
PC-cards
Game Consoles
Set-Top-Box
Network Devices
Wearable devices
MIMO Systems
Mutica Dual-band Wi-Fi Antenna
Part No. SR42W001 lamiiANT ® Product Specification
Mutica
Part No. SR42W001
Antennas for Wireless M2M Applications
Product Specification SR42W001-PS-1.2 Page 2
4. Part Number
Mutica: SR42W001
5. General Data
6. RF Characteristics
Product name
Mutica dual band Wi-Fi antenna
Part Number
SR42W001
Frequency
2.4-2.5GHz;4.9-6.0GHz
Polarization
Linear
Operating temperature
-40°C to140°C
Environmental condition test
ISO16750-4 5.1.1.1/5.1.2.1/5.3.2
Impedance with matching
50 Ω
Weight
< 0.5 g
Antenna type
SMD
Dimensions
11.3 x 5.0 x 0.8 (mm)
Typical performance
Conditions
Peak gain
2.0dBi
Average gain
-0.5dBi
Average efficiency
>75%
Maximum return loss
-12dB
Maximum VSWR
1.5:1
Typical performance
Conditions
Peak gain
3.0dBi
Average gain
-2.5dBi
Average efficiency
>65%
Maximum return loss
-6.0dB
Maximum VSWR
2.70:1
2.4 2.5 GHz frequency range
All data measured on
Antenovas evaluation PCB
Part No. SR42W001-U1
4.9 5.9 GHz frequency range
All data measured on
Antenovas evaluation PCB
Part No. SR42W001-U1
Mutica
Part No. SR42W001
Antennas for Wireless M2M Applications
Product Specification SR42W001-PS-1.2 Page 3
2000 2300 2600 2900 3200 3500 3800 4100 4400 4700 5000 5300 5600 5900
1
2
3
4
5
6
7
8
9
10
[M H z]
[] Atyune
1
2
34
2000 2300 2600 2900 3200 3500 3800 4100 4400 4700 5000 5300 5600 5900
-2 5
-2 0
-1 5
-1 0
-5
0
5
[M H z]
[dB ] Atyune
1
2
34
7. RF Performance
7.1 Return Loss
7.2 VSWR
Mutica
Part No. SR42W001
Antennas for Wireless M2M Applications
Product Specification SR42W001-PS-1.2 Page 4
7.3 Antenna patterns
7.3.1 2400 MHz 2500 MHz
3D pattern at 2.45GHz
Drag to rotate pattern and PCB by using Adobe Reader
(Click to Activate)
Mutica
Part No. SR42W001
Antennas for Wireless M2M Applications
Product Specification SR42W001-PS-1.2 Page 5
7.3.2 4900 MHz 5900 MHz
3D pattern at 5.45GHz
Drag to rotate pattern and PCB by using Adobe Reader
(Click to Activate)
Mutica
Part No. SR42W001
Antennas for Wireless M2M Applications
Product Specification SR42W001-PS-1.2 Page 6
8. Antenna Dimensions
All dimensions in mm
Bottom side dimensions
6 solder pads (1.1 x 0.9 mm)
L
W
H
Length
Width
Height
11.3
5.0
0.9
Pin 1 marker
Pin 1
Mutica
Part No. SR42W001
Antennas for Wireless M2M Applications
Product Specification SR42W001-PS-1.2 Page 7
9.0 Antenna footprint
The recommended host PCB footprint is below.
6 copper pads all 1.1 x 0.9 (mm)
*CAD files of the antenna footprint are available at www.antenova-m2m.com.
10.0 Schematic
The circuit for the antenna and the matching components is below. The RF feed
connection and GND connections are critical to the function of the antenna, and must be
followed as shown. This circuit can be used for the circuit capture of the host PCB.
1
2
3
4
5
6
Pi Network
Mutica
Part No. SR42W001
Antennas for Wireless M2M Applications
Product Specification SR42W001-PS-1.2 Page 8
11. Electrical Interface
11.1 Transmission Line
All transmission lines should be designed to have a characteristic impedance of 50Ω.
• The length of the transmission lines should be kept to a minimum
• Any other parts of the RF system like transceivers, power amplifiers, etc, should also
be designed to have an impedance of 50 Ω
Once the material for the PCB has been chosen (PCB thickness and dielectric constant),
a coplanar transmission line can easily be designed using any of the commercial
software packages for transmission line design. For the chosen PCB thickness, copper
thickness and substrate dielectric constant, the program will calculate the appropriate
transmission line width and gaps on either side of the track so the characteristic
impedance of the co-planar transmission line is 50 Ω.
11.2 Matching Circuit
The antenna requires a matching circuit that must be optimized for each product. The
matching circuit will require up to three components and the following pad layout should
be designed into the device so the correct circuit can be installed.
The Pi matching network must be placed close to the antenna feed to ensure it is
more effective in tuning the antenna.
Mutica
Part No. SR42W001
Antennas for Wireless M2M Applications
Product Specification SR42W001-PS-1.2 Page 9
12.0 Antenna Integration Guide
12.1 Antenna Placement
Whichever the host PCB size used, the antenna should be placed into the PCB
corner. Ideally Pin 1 should be closest to the PCB edge.
The antenna requires a copper clearance on all PCB layers under the antenna
section. The clear-out area is defined below. The clearance is minimal but must be
followed for the antenna to function correctly.
Pin 1 marker to PCB edge
13.4mm
5.7mm
Clearance area
Host board copper
0.5mm
Mutica
Part No. SR42W001
Antennas for Wireless M2M Applications
Product Specification SR42W001-PS-1.2 Page 10
For locations that are not on the corner the following clearances are required from
each side of the antenna to GND.
Centre PCB placement example
0.5mm from
antenna edge
16.7mm
5mm from
antenna edge
Mutica
Part No. SR42W001
Antennas for Wireless M2M Applications
Product Specification SR42W001-PS-1.2 Page 11
12.2 Host PCB Layout
The host PCB must ensure the footprint and clearance meets the antenna
specification. An example of the PCB layout shows the antenna footprint with
clearance. The antenna uses solder mask defined pads. Pin 2(GND) is shown
directly connecting to the GND in the shortest route. The feed connects to the
matching circuit close to the antenna.
Example host layout
Below shows the antenna footprint and clearance through all layers on the PCB.
Only the antenna pads and connections to feed and GND are present within the
antenna area
Example host layout
Mutica
Part No. SR42W001
Antennas for Wireless M2M Applications
Product Specification SR42W001-PS-1.2 Page 12
1000 1300 1600 1900 2200 2500 2800 3100 3400 3700 4000 4300 4600 4900 5200 5500 5800 6100 6400
-8 0
-7 0
-6 0
-5 0
-4 0
-3 0
-2 0
-1 0
0
10
[M H z]
[dB ] Atyune
1
2
3
4
13.0 MIMO Application example.
Mutica works well in multiple antenna systems with simple integration to ensure good
isolation between antennas. Below is an example of a 2 X MIMO system.
Two antennas placed perpendicular to each other. Both antennas were optimised
and matched for the same bands using the Antenova evaluation PCB. An S21
measurement between these antennas shows good isolation of <15dB minimum.
Antenna 1
Antenna 2
33mm
Mutica
Part No. SR42W001
Antennas for Wireless M2M Applications
Product Specification SR42W001-PS-1.2 Page 13
14.0 Reference Board
The reference board has been designed for evaluation purposes of SR42W001 includes a
SMA female connector.
SRCW004 Evaluation Board
To order a reference board contact sales@antenova-m2m.com
Please state if single or two antenna EVB is required.
53mm
24mm
Mutica
Part No. SR42W001
Antennas for Wireless M2M Applications
Product Specification SR42W001-PS-1.2 Page 14
15. Soldering
This antenna is suitable for lead free soldering.
The reflow profile should be adjusted to suit the device, oven and solder paste, while
observing the following conditions:
The maximum temperature should not exceed 240 ºC
However for lead free soldering, a maximum temperature of 255 ºC for no more
than 20 seconds is permitted.
The antenna should not be exposed to temperatures exceeding 120 ºC more
than 3 times during the soldering process.
16. Hazardous Material Regulation Conformance
The antenna has been tested to conform to RoHS requirements. A certificate of
conformance is available from Antenova M2M’s website.
17. Packaging
17.1 Optimal Storage Conditions
Temperature
-10ºC to 40ºC
Humidity
Less than 75% RH
Shelf life
24 Months
Storage place
Away from corrosive gas and direct sunlight
Packaging
Reels should be stored in unopened sealed
manufacturer’s plastic packaging.
Note: Storage of open reels of antennas is not recommended due to possible oxidization
of pads on antennas. If short term storage is necessary, then it is highly recommended
that the bag containing the antenna reel is re-sealed and stored in like storage conditions
as in above table.
The shelf life of the antenna is 2 years provided the factory seal on the package has not
been broken.
Mutica
Part No. SR42W001
Antennas for Wireless M2M Applications
Product Specification SR42W001-PS-1.2 Page 15
17.2 Tape Characteristics
Do
Ao
Bo
P0
P1
P2
1.55 +0.1
5.30 ± 0.1
11.605 ± 0.1
4.00 ± 0.1
8.00 ± 0.1
2.00 ± 0.1
E
F
W
K0
1.75 ± 0.1
11.50 ± 0.1
24.00 ± 0.3
1.40 ± 0.1
Dimensions in mm
Notes:
a) Sprocket hole pitch cumulative tolerance = ±0.2 per 10
b) Chamber not to exceed 1mm in 100mm
c) Ao and Bo measured on a plane 0.1mm above the bottom of the pocket.
d) K0 measured from a plane on the inside bottom of the pocket to the top surface of the
carrier.
Mutica
Part No. SR42W001
Antennas for Wireless M2M Applications
Product Specification SR42W001-PS-1.2 Page 16
17.3 Reel Dimensions
A
C
N
W1
178.0 ± 2.0
13.2 ± 0.5
60.0
14.0
All dimensions in mm
Quantity
Leading Space
Trailing Space
1000 pcs / reel
16 blank holders
24 blank holders
Mutica
Part No. SR42W001
Antennas for Wireless M2M Applications
Product Specification SR42W001-PS-1.2 Page 17
17.4 Box Dimensions
s
Width
(W)
Breadth
(B)
Thickness
(H)
203mm
188mm
40mm
17.5 Bag Properties
Reels are supplied in protective plastic packaging.
17.6 Reel Label Information
60.00mm
Antenova Limited
Antenova Asia Ltd
4F, No 324, Sec 1, Nei-Hu Road
Nei-Hu District, Taipei 11493, Taiwan, ROC
info@antenova-m2m.com / www.antenova-m2m.com
Description: Mutica
Part number: SR42W001
Quantity: 1000
Date Code: YYWW
Manufacturer’s code number: lamiiANT®
90.00m
m
Mutica
Part No. SR42W001
Antennas for Wireless M2M Applications
Product Specification DS-SR42W001-1.2 Release date June 2015 revised April 2016 Page 18
www.antenova-m2m.com
Corporate Headquarters
Antenova Limited
2nd Floor Titan Court
3 Bishop Square
Hatfield
AL10 9NA
UK
Tel: +44 1223 810600
Email: sales@antenova-m2m.com
North America Headquarters
Antenova Limited
100 Brush Creek Road, Suite 103
Santa Rosa
California 95404
USA
Tel: +1 707 890 5202
Email: sales@antenova-m2m.com
Asia Headquarters
Antenova Asia Limited
4F, No. 324, Sec. 1, Nei-Hu Road
Nei-Hu District
Taipei 11493
Taiwan, ROC
Tel: +886 (0) 2 8797 8630
Fax: +886 (0) 2 8797 6890
Email: sales@antenova-m2m.com
Copyright® Antenova Ltd. All Rights Reserved. Antenova ®, Antenova M2M ®, gigaNOVA ® ,the Antenova
product family names, and the Antenova and Antenova M2M logos are trademarks and/or registered trademarks
of Antenova Ltd. Any other names and/or trademarks belong to their respective companies.
The materials provided herein are believed to be reliable and correct at the time of printing. Antenova does not
warrant the accuracy or completeness of the information, text, graphics or other items contained within this
information. Antenova further assumes no responsibility for the use of this information, and all such information
shall be entirely at the user’s risk.