1
DEMO MANUAL DC2198A
Rev. A
DESCRIPTION
16-Channel Power Supply
System Featuring the LTC2980
Power System Manager
The DC2198A is a demonstration system for the LTC
®
2980
16-channel I
2
C/SMBus/PMBus power system manager
with EEPROM. The LTC2980 monitors and controls
16power supply rails. The DC2198A demonstrates the
ability of the LTC2980 to sequence, trim, margin, super-
vise, monitor, and log faults for sixteen power supply
rails. Each power supply channel’s output voltage is
monitored and the LTC2980 monitors its own internal
die temperature.
The DC2198A is a single circuit board that contains six-
teen independent power supply rails. The board employs
sixteen LTC3405A 300mA switch-mode regulators, which
are configured to be controlled by the LTC2980. The
LTC2980 is available in a BGA package and contains two
LTC2977 devices. This board provides a sophisticated
16-channel digitally programmable power supply system.
The rail voltages are programmable within the trim range
shown in the Performance Summary.
This demonstration system is supported by the LTpowerPlay
®
graphical user interface (GUI) that enables complete control
of all the features of the LTC2980. Together, the LTpowerPlay
software and DC2198A hardware system create a powerful
development environment for designing and testing LTC2980
configuration settings. These settings can be stored in the
device’s internal EEPROM or in a file. This file can later be
used to order pre-programmed devices or to program devices
in a production environment. The software displays all of the
configuration settings and real-time measurements from the
LTC2980. Telemetry allows easy access and decoding of
the fault log created by the LTC2980. The board comes pre-
programmed with the EEPROM values appropriate for the 16
power supplies used on the DC2198A. Just plug and play!
Multiple DC2198A boards can be cascaded together to
form a high channel count power supply (see Setup
Procedure for Multi-Board Arrays). This cascaded
configuration demonstrates features of the LTC2980
which enable timing and fault information to be shared
across multiple ICs. The user can configure up to four
DC2198A boards, thereby controlling up to 64 sepa-
rate power supply rails. Larger arrays of LTC2980s are
supported through programmable I2C base address or
bus segmentation.
The DC2198A demo board can be powered by an external
power supply, such as a +12VDC supply. Communication
with the software is provided through the DC1613 USB-to-
I2C/SMBus/PMBus Controller. The following is a checklist
of items which can be obtained from the Analog Devices
website or Analog Devices Field Sales.
• USB-to-I2C/SMBus/PMBus Controller (DC1613A)
• LTpowerPlay Software
DC2198A FEATURES
• Sequence, Trim, Margin, and Supervise Sixteen
Power Supplies
• Manage Faults, Monitor Telemetry, and Create Fault Logs
• PMBus Compliant Command Set
• Supported by LTpowerPlay GUI
• Margin or Trim Supplies to 0.25% Accuracy
• Fast OV/UV Supervisors Per Channel
• Supports Multichannel Fault Management
• Automatic Fault Logging to Internal EEPROM
• Operates Autonomously without Additional Software
• Sixteen OV/UV VOUT and Two VIN Supervisors
• Telemetry Reads Back VIN, VOUT, and Temperature
• 16-Channel Time-Based Output Sequencer
• I2C/SMBus Serial Interface
• Powered from 6V to 14VDC
• Available in 144-Pin 12mm × 12mm BGA
Design files for this circuit board are available.
All registered trademarks and trademarks are the property of their respective owners.
2
DEMO MANUAL DC2198A
Rev. A
Common Characteristics – Specifications Valid Over Full Operating Temperature Range
PARAMETER CONDITIONS
VALUE
MIN TYP MAX UNITS
Supply Input Voltage Range 6 14 V
ADC Total Unadjusted Error VIN_ADC ≥ 1V ±0.25 %
ADC Voltage Sensing Input Range Differential Voltage: VIN_ADC = (VSENSEP[n] – VSENSEM[n]) 0 6 V
PERFORMANCE SUMMARY
Specifications are at TA = 25°C
POWER SUPPLY CHANNEL CH(0:7) CH(8:15)
Manager ½ LTC2980 ½ LTC2980
Nominal Untrimmed Output Voltages 1.0V, 1.1V, 1.2V, 1.3V, 1.4V, 1.5V, 1.7V, 1.8V 2.0V, 2.2V, 2.5V, 2.7V, 3.0V, 3.1V, 3.2V, 3.3V
Rated Output Current 0.3A 0.3A
Default Margin Range ±5% ±5%
Output Trim Range (VFS_VDAC = 1.38V) +13/–19% +11/–15%
Temperature 1 Internal 11 Internal
GLOSSARY OF TERMS
The following list contains terms used throughout the
document.
Channel – The collection of functions that monitor, super-
vise, and trim a given power supply rail.
EEPROM – Nonvolatile memory (NVM) storage used to
retain data after power is removed.
Margin – Term used typically in board level testing that
increases/decreases the output voltage to look for sensi-
tivity/marginality problems
Monitor – The act of measuring voltage, current, and tem-
perature readings.
NVM – Nonvolatile memory, see EEPROM.
PMBus – An industry standard power-management proto-
col with a fully defined command language that facilitates
communication with power converters and other devices
in a power system.
Rail – The final output voltage that the power supply con-
troller manages.
Supervise – The act of quickly responding to a voltage,
current, temperature condition that is compared to pre-
programmed values (fault settings).
Trim – The act of adjusting the final output voltage. A
servo loop is typically used to trim the voltage.
3
DEMO MANUAL DC2198A
Rev. A
LTpowerPlay is a powerful Windows-based development
environment that supports Analog Devices Power System
Management ICs with EEPROM, including the LTC2980
16-channel PMBus Power System Manager. The soft-
ware supports a variety of different tasks. You can use
LTpowerPlay to evaluate Analog Devices ICs by connect-
ing to a demo board system. LTpowerPlay can also be
used in an offline mode (with no hardware present) in
order to build a multi-chip configuration file that can be
saved and re-loaded at a later time. LTpowerPlay pro-
vides unprecedented diagnostic and debug features. It
becomes a valuable diagnostic tool during board bring-up
to program or tweak the power management scheme in
LTpowerPlay GUI SOFTWARE
Figure1. Screen Shot of the LTpowerPlay GUI
a system or to diagnose power issues when bringing up
rails. LTpowerPlay utilizes the DC1613 I
2
C/SMBus/PMBus
Controller to communicate with one of many potential tar-
gets, including the DC2198A demo system or a customer
board. The software also provides an automatic update
feature to keep the software current with the latest set
of device drivers and documentation. The LTpowerPlay
software can be downloaded.
To access technical support documents for ADI Power
System Management Products visit “Help, View Online
help” on the LTpowerPlay menu.
SYSTEM TREE OF
ALL DEVICES
CONFIGURATION SETTINGS
FOR ALL DEVICES IN
SYSTEM TREE
REAL-TIME
TELEMETRY
DATA
CHIP DASHBOARD
(KEY ASPECTS OF
SELECTED CHIP)
DISPLAY OF SELECTED
PARAMETER (CONFIG
OR TELEMETRY)
ACROSS SYSTEM
IDEALIZED ON/OFF
SUPPLY WAVEFORMS
SCOPE-LIKE
TELEMETRY WINDOW
4
DEMO MANUAL DC2198A
Rev. A
QUICK START PROCEDURE
The following procedure describes how to set up a
DC2198A demo system.
1. Download and install the LTpowerPlay GUI.
2. Remove the board from the ESD protective bag and
place it on a level surface. Connect the DC1613 I2C/
SMBus/PMBus Controller to the DC2198A board using
the 12-pin ribbon cable.
3. Confirm that the CONTROL switch is set to the RUN
position.
4. Plug the USB to I2C/SMBus/PMBus Controller into a
USB port on your PC. The board should power up with
all power good LEDs and +5V LED illuminated green.
The USB-to-I2C/SMBus/PMBus Controller supplies
~100mA of current which should be sufficient for a
single demo board.
5. If multiple boards are being powered, connect a +12VDC
power supply with >0.5A capacity to the VIN input jack
of the DC2198A.
6. Launch the LTpowerPlay GUI.
a. The GUI automatically identifies the DC2198A and
builds a system tree. The system tree on the left
hand side should look like this:
Figure2. Connecting DC2198A Board and the DC1613 I2C/SMBus/PMBus Controller
Note: For multiple board arrays, the GUI automati-
cally ensures each device has a unique address. In
this scenario, it is recommended at this
point to store these addresses to NVM
(EEPROM) by clicking the “RAM -> NVM”
icon in the toolbar.
5
DEMO MANUAL DC2198A
Rev. A
QUICK START PROCEDURE
b. A green message box will be displayed for a few
seconds in the lower left hand corner confirming
that the DC2198A is communicating:
c. Save the demo board configuration to a (*.proj) file
by clicking the “Save” icon. This creates a backup
file. Name it whatever you want.
Loading a DC2198A Configuration (*.proj) File with the GUI
1. In the upper left hand corner of the GUI, File > Open >
browse to your *.proj file. This will load the file intotheGUI.
2. Click on the “Go Online” icon, then click on the
“PC->RAM” arrow. This loads the configuration into
the working RAM of the LTC2980.
3. To store the configuration to NVM (EEPROM), click on
the “RAM -> NVM” icon.
Figure3. DC2198A Top Side Details
7. The CONTROL switch is configured to control all
16channels. Slide the switch to RUN to enable, OFF
to disable all channels. For multiple board arrays, the
CONTROL switch is wired to a signal that is common
across all boards. All CONTROL switches must be set
to the RUN position to enable all boards.
CH0 TO CH7
OUTPUTS LTC2980
CASCADING
CONNECTOR VIN = 6V TO 14V
DC1613
CONNECTOR
CONTROL
SWITCH
CASCADING
CONNECTOR
CH8 TO CH15
OUTPUTS
PUSHBUTTON
TO FORCE
A FAULT
PUSHBUTTON
TO FORCE
A RESET
RESET
FAULT
ALERT
I2C PINS
6
DEMO MANUAL DC2198A
Rev. A
COMMON DEMO BOARD OPERATIONS
MARGIN ALL RAILS
The LTC2980 power system manager not only moni-
tors each of the sixteen outputs but also can margin the
outputs either high or low. Margining is the operation
that moves a rail either up or down for testing purposes.
It allows a system to be fully characterized over supply
limits without the use of external hardware or resources.
The GUI provides an easy way to margin all
rails high or all low by clicking one of four but-
tons. To invoke the margining dialog, click the
GroupOp icon in the toolbar. The buttons labeled “ignore
faults” will margin without creating a fault even if the fault
limits are exceeded.
A look at the telemetry window shows the effect of the
margin high or margin low operation. The following
screen shot shows all rails going from nominal setpoints
to margin high, margin low, and back to nominal voltages.
Each LTC2977 inside the LTC2980 has a multiplexed ADC
that is used to provide voltage, current, and temperature
readback values. The telemetry plot in the GUI is similar
to a multichannel oscilloscope which is capable of dis-
playing any parameter that is displayed in the telemetry
window. Due to the nature of a multiplexed ADC converter,
it has an associated ADC loop time. The total ADC loop
time (~100ms to 160ms) for a given channel is dependent
on the device’s configuration. Refer to the LTC2977 data
sheet for complete ADC timing specifications.
Creating a Fault
There is a pushbutton on the DC2198A board that is used
to force a fault and demonstrate the demo board’s abil-
ity to detect it and respond according to the configura-
tion. When depressed, the pushbutton creates a fault on
channel10, the 2.5V output (GUI channel U1:2). The user
should see all outputs power off, the fault LED momen-
tarily illuminate, the alert LED illuminate continuously, and
all rails sequence back on after a retry period. The user
may also short any power supply output indefinitely. This
is a good way to induce UV faults and
shows that a shorted channel will not
be damaged. Use a jumper wire or a
coin to short any output.
The LTC2980 has a feature, which allows it to sequence its
channels off in a controlled manner, as opposed to turning
all rails off immediately. The SequenceOffOnFault bit in
the MFR_CONFIG_LTC2977 register sets this behavior on
each channel. The DC2198A demo board has been con-
figured to sequence off all channels when a fault occurs.
Pressing the “CREATE FAULT” pushbutton causes the
7
DEMO MANUAL DC2198A
Rev. A
COMMON DEMO BOARD OPERATIONS
Fault pin to be asserted low which triggers all rails to
power down based on the TOFF_DELAY times.
Figure4 shows FAULTB asserting low, and each of the
channels sequencing off per the TOFF_DELAY settings.
Figure5 shows the same except that the 3.0V rail (CH12)
does not have its SequenceOffOnFault bit set. The 3.0V
rail powers down immediately as defined by the fault
response setting.
Clearing a Fault
To clear a fault, the user may click the CF icon in the GUI
or simply push the RESET pushbutton on the demo board.
In both cases, the red (+) on the CF icon and alert LED on
the board will be cleared. You will notice that all rails are
automatically re-enabled after a programmable
retry period. The alert LED may be cleared by
pushing the Clear Faults (CF) icon in the GUI.
Figure5. Sequencing Off (SeqOffOnFault = 0)Figure4. Sequencing Off (SeqOffOnFault = 1)
After clearing faults, the system tree may remain “yel-
low” if any nonvolatile fault logs are present. For further
information, see the Working with the Fault Log section.
Resetting the DC2198A
A reset pushbutton is provided on the board. To reset all
devices on the DC2198A board and reload the EEPROM
contents into operating memory (RAM), press RESET
(SW2) on the DC2198A.
DC2198A LEDs
Each individual channel on DC2198A also has its own
green “power good” LED (CH0 through CH15). When USB
power (DC1613 Controller) or external power (6V-14V
jack) is applied, the +5V green LED will illuminate, indi-
cating that the LTC2980 is powered. The red LEDs will
illuminate when an alert or a fault has occurred.
Sequencing Output Channels
The LTC2980 has been pre-programmed to different
TON_DELAY values for each channel. The TON_DELAY
parameter is applied to each device relative to its respec-
tive CONTROL pin. When multiple demo boards are
connected together, all CONTROL pins are wire OR’d.
Therefore the TON delays are enforced relative to one
8
DEMO MANUAL DC2198A
Rev. A
COMMON DEMO BOARD OPERATIONS
edge. The same applies to TOFF_DELAY values. When the
CONTROL switch is set to the OFF position, all rails will
power down sequentially based on each of the device’s
TOFF_DELAY values. Figure6 shows an oscilloscope
screen capture of three output rails sequencing up and
down in response to the CONTROL pin.
Each channel has an LED, which visually indicates if the
channel has power. When the CONTROL pin is switched
on and off, you will observe the relative on/off timing of
the 16 channels.
For the LTC2980, the TON_DELAY and TOFF_DELAY val-
ues extend to 13.1 seconds, providing very long on and
off sequencing of power supply rails.
Figure6. Sequencing Output Channels with DC2198A Using TON_DELAY and TOFF_DELAY
Figure8. TOFF_DELAY Configuration
Figure7. TON_DELAY Configuration
9
DEMO MANUAL DC2198A
Rev. A
COMMON DEMO BOARD OPERATIONS
Figure9. Why Am I Off Tool in the LTpowerPlay GUI
Why Am I Off? Tool
Use the Why am I Off tool in the LTpowerPlay GUI to
diagnose the reason a power supply channel is turned
off. The tool can be located in the top right corner of the
GUI, next to the “Register Information” tab. Hover your
cursor over this tab to show the tool.
10
DEMO MANUAL DC2198A
Rev. A
ADVANCED DEMO BOARD OPERATIONS
WHAT IS A FAULT LOG?
A fault log is a nonvolatile record of the power system
leading up to the time of fault. It holds the most recent
monitored values (uptime, voltage, current, temperature)
that can be analyzed to help determine the cause of the
fault. It is a powerful diagnostic feature of the LTC2980
on the DC2198A demo board.
Create a Fault and Fault Log
To create a fault log, you must create a fault, as described
in the Creating A Fault section. If multiple boards are con-
figured, select the appropriate device in the system tree by
clicking on the appropriate LTC2980 chip. We will proceed
to work with the fault log.
Working with the Fault Log
Once a fault has occurred, the Fault Log (FL)
icon will show a red (+) sign on it, indicating that
the GUI has detected a fault log in the device.
Clicking the icon will bring up a dialog box. Note that it
is context sensitive. Be sure that the desired device is
selected in the system tree.
Notice that the checkbox “Log to EEPROM on Fault” is
checked. Once a fault occurs, the device will automati-
cally write the fault log data to EEPROM (NVM). At this
point, the log is locked and will not change until it is
cleared by the user. To read the EEPROM log data, first
click the “NVM->RAM” button. At this point the RAM
Log is locked and not updated even though the telemetry
readings continue. Click the “Read RAM Log” button. The
log data will appear in the text box below.
11
DEMO MANUAL DC2198A
Rev. A
ADVANCED DEMO BOARD OPERATIONS
The log contains timestamp, up time, channel voltage
readings, an input voltage reading, an on-chip tempera-
ture reading, etc. There will be a number of loops; each
loop contains data obtained in one ADC loop time with the
most recent ADC loop data on top and the oldest data at
the bottom of the log. The up time indicates, at the time
of fault, the amount of time the device has been powered
up or time since the previous reset.
In this case, the fault log will show that channel U1:2
faulted due to a VOUT_UV_FAULT condition. On the pre-
vious telemetry loop, the channel voltage reading was a
nominal value (2.5V).
To clear the fault log, click the “Clear/Rearm EEPROM
Log” button. This allows the selected device to be ready
for a new fault event. To clear all faults, click the Clear
Faults (CF) icon.
Fault Sharing Setup in the GUI
Fault sharing provides a means of propagating a fault
detected by a power system manager to other power sys-
tem managers via FAULT pins. Use the Fault Sharing Setup
Tool to configure the fault sharing in the GUI. Select the
LTC2980 labeled U0 in the system tree. Go to Utilities >
Fault Sharing Diagram. For more details on this topic,
please refer to the Fault Management section in the data
sheet.
The fault-sharing dialog will appear as shown in Figure10.
All Response and all Propagate switches are closed
by default. In this configuration, a fault on one of the
LTC2980 channels will shut down all 16 channels, and a
fault on any LTC2980 channel will propagate to all chan-
nels on the DC2198A demo board since the fault pins are
tied together.
Note: All FAULT pins on the LTC2980 are tied together on
the DC2198A demo board. These pins are open drain and
have a common pull-up resistor to provide a logic high
level (inactive). All FAULT pins are active low.
There are two types of actions to fault conditions: How a
channel responds to another channel’s fault and whether
a particular channel propagates a fault to other channels.
FAULT pins are bi-directional, meaning the device may
drive its fault pin low (output) or may respond to the fault
pin when another device drives it low (input). Because all
fault pins are wire OR’d on the DC2198A, this hardware
configuration allows one to program each device’s fault
settings on a channel-by-channel basis. By default, the
LTC2980 is configured to shut down all channels if other
devices fault and to broadcast its own fault via the FAULT
12
DEMO MANUAL DC2198A
Rev. A
ADVANCED DEMO BOARD OPERATIONS
pins. A fault on these channels will cause only that chan-
nel to fault off. You can think of the “Response” switches
as “shut this channel down when another channel faults”,
and the “Propagate” switches as “drive a fault pin to
broadcast to other channels that this channel faulted”.
Fault Configuration Example
Let’s explore two different examples. Suppose we do not
want channel U0:0 (CH0 1.0V rail) to propagate its fault
to the other channels when it faults. And suppose we do
not want channel U0:1 (CH1 1.1V rail) to shut down in
response to another channel’s fault. We can configure
the switches as shown in Figure11. Simply click
the switches to open/close. Click OK to close the
dialog box. Click the “PC -> RAM” icon to write
the changes to the DC2198A.
We can now create a fault on U0:0 (CH0) by shorting
the output to ground. You may use a coin or a jumper
to temporarily connect CH0 to the GND turret. You will
notice that the channel shuts off but the other channels
remain powered up because its fault is not propagated to
the other channels. After the retry period, channel U0:0
(CH0) will power back up. We can now observe the effect
of changing the response setting on U0:1 (CH1). If you
short U0:2 (CH2 1.2V rail) to ground, notice that all rails
shut down except U0:1 (CH1). This is an example of a
keep-alive channel that remains powered up independent
of faults on other channels.
Figure10. Fault Sharing Utility in LTpowerPlay GUI
Figure11. Updated Fault Sharing Configuration
13
DEMO MANUAL DC2198A
Rev. A
SETUP PROCEDURE FOR MULTI-BOARD ARRAYS
Multiple DC2198A boards can be combined to control
up to 64 independent power supplies. Four boards may
be cascaded. The number of boards is limited by an I/O
expander chip that has three address pins, allowing 8dif-
ferent combinations. This setup demonstrates the coor-
dinated fault responses and accurate time base shared
across multiple LTC2980 devices.
Procedure:
1. Stack the boards side-by-side by plugging JP1 of one
board into JP2 of another DC2198A board.
2. Ensure different slave address settings for each of the
boards. The address of each board is set by the DIP
switch JP3 on the backside of the board. The setting
must be unique for each board in the array.
3. Plug in the +12V VIN power into one of the boards as shown
in Figure12. Only one +12V power source is allowed.
4. The USB to I2C/SMBus/PMBus Controller may
be plugged into any board. If no devices show
up in the GUI, click the magnifying glass icon
to enumerate the I2C bus and find the addresses of the
parts. Go to step #2 to ensure that each board has a
unique DIP switch setting.
5. Since the individual CONTROL lines are connected
across the boards (CTRL is a common signal across
all boards in the array), make sure that all CONTROL
switches are set to the RUN position.
6. Re-launch LTpowerPlay. It will enumerate the entire
board array and build a representative system tree and
read all hardware settings into the GUI.
ATTENTION: Once the GUI has launched,
click the “RAM-> NVM” icon in the toolbar to
ensure that the slave addresses are retained
after a power off or reset. Otherwise you may lose
communication with the slaves after a power cycle or
reset event.
Figure12. Array of Multiple DC2198A Demo Boards
14
DEMO MANUAL DC2198A
Rev. A
SETUP PROCEDURE FOR MULTI-BOARD ARRAYS
Ensuring Slave Addresses Do Not Conflict
There is a small DIP switch on the backside of the DC2198A.
It is used to set the slave address of an I/O expander
which provides for the addition of multiple boards to a
Figure13. DIP Switch Set to All Zeros (0x20) Figure14. DIP Switch Set to All Ones (0x27)
setup. The I/O expander has a base address of 0x20. The
DIP switch settings set the offset. The three switches that
may be changed are labeled A0, A1, A2. Examples below
set the boards to addresses 0x20 and0x27.
15
DEMO MANUAL DC2198A
Rev. A
DC2198A DETAILS – TOP
Table1. DC2198A: Default Switch Configuration (Default Position Shown in Grey in the Figure Above)
REFERENCE DESIGNATOR SIGNAL NAME USAGE DEFAULT
JP3 SCLK, A0, A1, A2 DIP Switch Used to Set the Address Offset of LTC2980 OPEN
S1 CONTROL0 Switch Used to Enable/Disable the CONTROL0 Input Pin of LTC2980 RUN
TEST POINT
TURRETS FOR THE
CONTROL SIGNALS
CONNECTOR FOR
CASCADING
MULTIPLE DC2198A
RESET SWITCH
CREATE FAULT SWITCH
CONNECTOR FOR
CASCADING
MULTIPLE DC2198A
CONTROL SWITCH
ALERT AND FAULT LEDs
LED INDICATING +5V
INPUT POWER TO LTC2980
17
DEMO MANUAL DC2198A
Rev. A
PARTS LIST
ITEM QTY REFERENCE PART DESCRIPTION MANUFACTURER/PART NUMBER
Required Circuit Components
1 1 U10 IC 16-CH POWER SYSTEM MANAGER BGA144 ANALOG DEVICES: LTC2980CY#PBF
Additional Demo Board Circuit Components
2 16 C1, C2, C3, C4, C5, C6, C7,
C8, C38, C39, C40, C41, C42,
C43, C44, C45
CAP CER 220pF 50V 10% NPO 0603 NIC: NMC0603NPO221J50TRPF
3 18 C9, C10, C11, C12, C13, C14,
C15, C16, C19, C27, C28,
C29, C30, C31, C32, C33,
C34, C46
CAP CER 10μF 10V 10% X5R 1210 KEMET: C1210C106K8PACTU
4 1 C17 CAP CER 10μF 25V 20% X5R 1210 TAIYO YUDEN: TMK325BJ106MM-T
5 26 C18, C26, C55, C56, C57,
C58, C59, C60, C61, C62,
C70, C71, C72, C73, C74,
C75, C76, C77, C86, C87,
C88, C89, C90, C91, C92, C93
CAP CER 0.1μF 16V 10% X7R 0603 NIC: NMC0603X7R104K16TRPF
6 2 C20, C69 CAP CER 68pF 50V 5% NPO 0603 AVX: 06035A680JAT2A
7 17 C21, C47, C48, C49, C50,
C51, C52, C53, C54, C78,
C79, C80, C81, C82, C83,
C84, C85
CAP CER 22μF 10V 10% X5R 1210 KEMET: C1210C226K8PACTU
8 1 C22 CAP CER 10nF 25V 10% X7R 0603 YAGEO: CC0603KRX7R8BB103
9 1 C23 CAP CER 47pF 50V 5% NPO 0603 AVX: 06035A470JAT2A
10 7 C24, C25, C35, C36, C37,
C63, C66
CAP CER 1μF 16V 10% X7R 0603 TAIYO YUDEN: EMK107B7105KA-T
11 2 C64, C67 CAP CER 4.7μF 16V 10% X5R 0603 TDK: C1608X5R1C475K
12 1 C65 CAP TANT 47μF 16V 20% 7343 KEMET: T520D476M016ATE035
13 1 C68 CAP CER 4.7pF 50V NP0 0603 MURATA: GRM1885C1H4R7CZ01D
14 1 D1 DUAL DIODE SCHOTTKY 30V CC SOT-323-3 DIODES/ZETEX: SBR0330CW-7
15 16 L1, L2, L3, L4, L5, L6, L7, L8,
L10, L11, L12, L13, L14, L15,
L16, L17
INDUCTOR SHLD POWER 4.7μH SMD ABRACON: ASPI-0315FS-4R7M-T2
WURTH: 744029004 (ALTERNATE)
16 1 L9 INDUCTOR POWER 2.2μH 2.85A SMD VISHAY: IHLP1616BZER2R2M01
17 2 LED1, LED2 LED RED HI BRT SS TYPE LO CUR SM PANASONIC: LNJ214R82RA
18 17 LED3, P1, P2, P3, P4, P5, P6,
P7, P8, P9, P10, P11, P12,
P13, P14, P15, P16
LED GREEN HIGH BRIGHT ESS SMD PANASONIC: LNJ326W83RA
19 17 Q1, Q2, Q3, Q4, Q5, Q6, Q7,
Q8, Q9, Q10, Q11, Q12, Q13,
Q14, Q15, Q16, Q17
MOSFET N-CH 30V 900mA SOT323-3 DIODES INC: DMG1012UW-7 -OR- VISHAY/
SILICONIX: SI1304BDL-T1-GE3
20 33 R1, R2, R3, R4, R5, R6, R7,
R8, R29, R58, R59, R60, R61,
R62, R63, R64, R65, R74,
R75, R76, R77, R78, R79,
R80, R81, R119, R120, R121,
R122, R123, R124, R125,
R126
RES 100kΩ 1/10W 1% 0603 SMD YAGEO: RC0603FR-07100KL
21 2 R9, R107 RES 402kΩ 1/10W 1% 0603 SMD YAGEO: RC0603FR-07402KL
18
DEMO MANUAL DC2198A
Rev. A
ITEM QTY REFERENCE PART DESCRIPTION MANUFACTURER/PART NUMBER
22 1 R10 RES 267kΩ 1/10W 1% 0603 SMD YAGEO: RC0603FR-07267KL
23 1 R11 RES 200kΩ 1/10W 1% 0603 SMD YAGEO: RC0603FR-07200KL
24 1 R12 RES 158kΩ 1/10W 1% 0603 SMD YAGEO: RC0603FR-07158KL
25 1 R13 RES 133kΩ 1/10W 1% 0603 SMD YAGEO: RC0603FR-07133KL
26 1 R14 RES 115kΩ 1/10W 1% 0603 SMD YAGEO: RC0603FR-07115KL
27 1 R15 RES 88.7kΩ 1/10W 1% 0603 SMD YAGEO: RC0603FR-0788K7L
28 1 R16 RES 80.6kΩ 1/10W 1% 0603 SMD YAGEO: RC0603FR-0780K6L
29 17 R17, R18, R19, R20, R21,
R22, R23, R24, R35, R39,
R40, R41, R42, R43, R44,
R45, R46
RES 3.01kΩ 1/10W 1% 0603 SMD YAGEO: RC0603FR-073K01L
30 10 R25, R32, R36, R47, R56,
R57, R98, R99, R100, R135
RES 10.0kΩ 1/10W 1% 0603 SMD YAGEO: RC0603FR-0710KL
31 2 R26, R27 RES 698Ω 1/10W 1% 0603 SMD YAGEO: RC0603FR-07698RL
32 2 R28, R102 RES 73.2kΩ 1/10W 1% 0603 SMD YAGEO: RC0603FR-0773K2L
33 1 R30 RES 46.4kΩ 1/10W 1% 0603 SMD YAGEO: RC0603FR-0746K4L
34 1 R31 RESISTOR 0603 OPTION
35 2 R33, R38 RES 249Ω 1/10W 1% 0603 SMD YAGEO: RC0603FR-07249RL
36 1 R34 RES 1.00kΩ 1/10W 1% 0603 SMD YAGEO: RC0603FR-071KL
37 3 R37, R136, R137 RES ARRAY 10kΩ 4 RES 1206 VISHAY/DALE: CRA06S08310K0JTA
38 1 R48 RES 66.5kΩ 1/10W 1% 0603 SMD YAGEO: RC0603FR-0766K5L
39 1 R49 RES 57.6kΩ 1/10W 1% 0603 SMD YAGEO: RC0603FR-0757K6L
40 1 R50 RES 47.5kΩ 1/10W 1% 0603 SMD YAGEO: RC0603FR-0747K5L
41 1 R51 RES 42.2kΩ 1/10W 1% 0603 SMD YAGEO: RC0603FR-0742K2L
42 1 R52 RES 36.5kΩ 1/10W 1% 0603 SMD YAGEO: RC0603FR-0736K5L
43 1 R53 RES 34.8kΩ 1/10W 1% 0603 SMD YAGEO: RC0603FR-0734K8L
44 1 R54 RES 33.2kΩ 1/10W 1% 0603 SMD YAGEO: RC0603FR-0733K2L
45 1 R55 RES 32.4kΩ 1/10W 1% 0603 SMD YAGEO: RC0603FR-0732K4L
46 16 R66, R67, R68, R69, R70,
R71, R72, R73, R127, R128,
R129, R130, R131, R132,
R133, R134
RES 470Ω 1/4W 5% 1210 SMD ROHM SEMICONDUCTOR: MCR25JZHJ471
47 16 R82, R84, R86, R88, R90,
R92, R94, R96, R104, R106,
R108, R110, R112, R114,
R116, R118
RES 100Ω 1/10W 0603 SMD
48 1 R83 RES 182kΩ 1/10W 1% 0603 SMD YAGEO: RC0603FR-07182KL
49 1 R85 RES 191kΩ 1/10W 1% 0603 SMD YAGEO: RC0603FR-07191KL
50 1 R87 RES 196kΩ 1/10W 1% 0603 SMD YAGEO: RC0603FR-07196KL
51 1 R89 RES 205kΩ 1/10W 1% 0603 SMD YAGEO: RC0603FR-07205KL
52 1 R91 RES 226kΩ 1/10W 1% 0603 SMD YAGEO: RC0603FR-07226KL
53 1 R93 RES 243kΩ 1/10W 1% 0603 SMD YAGEO: RC0603FR-07243KL
54 1 R95 RES 274kΩ 1/10W 1% 0603 SMD YAGEO: RC0603FR-07274KL
55 1 R97 RES 301kΩ 1/10W 1% 0603 SMD YAGEO: RC0603FR-07301KL
PARTS LIST
19
DEMO MANUAL DC2198A
Rev. A
ITEM QTY REFERENCE PART DESCRIPTION MANUFACTURER/PART NUMBER
56 1 R101 RES 2.49kΩ 1/10W 1% 0603 SMD YAGEO: RC0603FR-072K49L
57 1 R103 RES 340kΩ 1/10W 1% 0603 SMD YAGEO: RC0603FR-07340KL
58 1 R105 RES 357kΩ 1/10W 1% 0603 SMD YAGEO: RC0603FR-07357KL
59 1 R109 RES 374kΩ 1/10W 1% 0603 SMD YAGEO: RC0603FR-07374KL
60 1 R111 RES 464kΩ 1/10W 1% 0603 SMD YAGEO: RC0603FR-07464KL
61 1 R113 RES 511kΩ 1/10W 1% 0603 SMD YAGEO: RC0603FR-07511KL
62 1 R115 RES 549kΩ 1/10W 1% 0603 SMD YAGEO: RC0603FR-07549KL
63 1 R117 RES 604kΩ 1/10W 1% 0603 SMD YAGEO: RC0603FR-07604KL
64 16 U1, U2, U3, U4, U5, U6, U7,
U8, U13, U14, U15, U16, U17,
U18, U19, U20
IC BUCK SYNC ADJ 0.3A SOT23-6 ANALOG DEVICES: LTC3405AES6#TRMPBF
65 1 U9 IC BUCK SYNC 2.5A 16-QFN ANALOG DEVICES: LTC3604IUD#PBF
66 1 U11 IC DUAL 4A DIODES 16-MSOP ANALOG DEVICES: LTC4415IMSE#PBF
67 1 U12 IC 2-WIRE BUS BUFFER 8-MSOP ANALOG DEVICES: LTC4313CMS8-2#PBF
68 1 U21 IC I/O EXPANDER I2C 8B 20-QFN MICROCHIP: MCP23008-E/ML
69 1 U22 IC EEPROM 2KBIT 400kHz SOT23-5 MICROCHIP TECHNOLOGY: 24AA02T-I/OT
70 1 U23 IC VREF SERIES PREC TSOT-23-6 ANALOG DEVICES:
LT6654BMPS6-1.25#TRMPBF
71 1 U24 IC BUFFER DUAL NON-INV SC706 TI: SN74LVC2G34DCKR
Hardware – For Demo Board Only
72 1 J1 CONN PWR JACK 2.1X5.5mm HIGH CUR CUI INC: PJ-002AH
73 1 J2 CONN HEADER 12POS 2mm STR DL PCB FCI: 98414-G06-12ULF
74 1 JP1 CONN RECEPT 2mm DUAL R/A 14POS SULLINS: NPPN072FJFN-RC
75 1 JP2 CONN HEADER 14POS 2mm R/A GOLD MOLEX: 87760-1416
76 1 JP3 SWITCH DIP 4POS HALF PITCH SMD C&K COMPONENTS: TDA04H0SB1
77 4 MH1, MH2, MH3, MH4 SPACER STACKING #4 SCREW NYLON KEYSTONE: 8831
78 1 S1 SW SLIDE DPDT 6VDC 0.3A PCMNT C&K COMPONENTS: JS202011CQN
79 1 SW1 BLK SWITCH TACTILE SPST-NO 0.05A 12V C&K COMPONENTS: PTS635SL25SMTR LFS
80 1 SW2 RED SWITCH TACTILE SPST-NO 0.05A 12V C&K COMPONENTS: PTS635SK25SMTR LFS
81 29 TP1, TP2, TP3, TP4, TP5,
TP6, TP7, TP8, TP9, TP10,
TP11, TP12, TP13, TP14,
TP15, TP16, TP17, TP18,
TP19, TP21, TP22, TP23,
TP24, TP25, TP26, TP27,
TP28, TP29, TP30
TERM SOLDER TURRET 0.219" H 0.109" L MILL-MAX: 2501-2-00-80-00-00-07-0
82 1 TP20 TERM SOLDER TURRET 0.156" H 0.084" L MILL-MAX: 2308-2-00-80-00-00-07-0
PARTS LIST
20
DEMO MANUAL DC2198A
Rev. A
SCHEMATIC DIAGRAM
LTC2980 CH0 Power Stage LTC2980 CH1 Power Stage
LTC2980 CH2 Power Stage LTC2980 CH3 Power Stage
1210
1210 1210
1210
1210 1210
1210
1210 1210
1210
1210 1210
CH0
1.0V
CH1
1.1V
CH2
1.2V
CH3
1.3V
2 1
2 1
2 1
2 1
LTC3405AES6
4.7uH
100k
470
10u/10V
GND
VDD GREEN
Si1308EDL
22u/10V
220p
GND GND
GND
604k
100n
100
GND
GND
VDD
3.01k
100k
402k
GND
LTC3405AES6
4.7uH
100k
470
10u/10V
GND
VDD GREEN
Si1308EDL
22u/10V
220p
GND GND
GND
549k
100n
100
GND
GND
VDD
3.01k
100k
267k
GND
LTC3405AES6
4.7uH
100k
470
10u/10V
GND
VDD GREEN
Si1308EDL
22u/10V
220p
GND GND
GND
511k
100n
100
GND
GND
VDD
3.01k
100k
200k
GND
LTC3405AES6
4.7uH
100k
470
10u/10V
GND
VDD GREEN
Si1308EDL
22u/10V
220p
GND GND
GND
464k
100n
100
GND
GND
VDD
3.01k
100k
158k
GND
1
2
34
6
5
U1
L1
R126
R134
C9
P1
32
1
Q17
C85
C1
R117
C77
R118
R17
R1
R9
1
2
34
6
5
U2
L2
R125
R133
C10
P2
32
1
Q16
C84
C2
R115
C76
R116
R18
R2
R10
1
2
34
6
5
U3
L3
R124
R132
C11
P3
32
1
Q15
C83
C3
R113
C75
R114
R19
R3
R11
1
2
34
6
5
U4
L4
R123
R131
C12
P4
32
1
Q14
C82
C4
R111
C74
R112
R20
R4
R12
DACP_CH0
RUN_CH0
VSNSP_CH0
VOUT_CH0
DACP_CH1
RUN_CH1
VSNSP_CH1
VOUT_CH1
DACP_CH2
RUN_CH2
VSNSP_CH2
VOUT_CH2
DACP_CH3
RUN_CH3
VSNSP_CH3
VOUT_CH3
1 PRODUCTION MIKE P. 01-18-2017
1. ALL RESISTORS ARE 1% 0603.
2. ALL CAPACITORS ARE 16V 0603.
3. THE INTERMEDIATE BUS IS VDD=5.0V
VIN
GND
SW
MODE RUN
VFB
VIN
GND
SW
MODE RUN
VFB
VIN
GND
SW
MODE RUN
VFB
VIN
GND
SW
MODE RUN
VFB
CUSTOMER NOTICE
B
SCALE = NONE
LTC CONFIDENTIAL
FOR CUSTOMER
USE ONLY
PCB DES.
APP ENG. www.linear.com
-
21
DEMO MANUAL DC2198A
Rev. A
SCHEMATIC DIAGRAM
LTC2980 CH4 Power Stage LTC2980 CH5 Power Stage
LTC2980 CH6 Power Stage LTC2980 CH7 Power Stage
1210
1210 1210
1210
1210 1210
1210
1210 1210
1210
1210 1210
CH4
1.4V
CH5
1.5V
CH6
1.7V
CH7
1.8V
2 1
2 1
2 1
2 1
LTC3405AES6
4.7uH
100k
470
10u/10V
GND
VDD GREEN
Si1308EDL
22u/10V
220p
GND GND
GND
374k
100n
100
GND
GND
VDD
3.01k
100k
133k
GND
LTC3405AES6
4.7uH
100k
470
10u/10V
GND
VDD GREEN
Si1308EDL
22u/10V
220p
GND GND
GND
402k
100n
100
GND
GND
VDD
3.01k
100k
115k
GND
LTC3405AES6
4.7uH
100k
470
10u/10V
GND
VDD GREEN
Si1308EDL
22u/10V
220p
GND GND
GND
357k
100n
100
GND
GND
VDD
3.01k
100k
88.7k
GND
LTC3405AES6
4.7uH
100k
470
10u/10V
GND
VDD GREEN
Si1308EDL
22u/10V
220p
GND GND
GND
340k
100n
100
GND
GND
VDD
3.01k
100k
80.6k
GND
1
2
34
6
5
U5
L5
R122
R130
C13
P5
32
1
Q13
C81
C5
R109
C73
R110
R21
R5
R13
1
2
34
6
5
U6
L6
R121
R129
C14
P6
32
1
Q12
C80
C6
R107
C72
R108
R22
R6
R14
1
2
34
6
5
U7
L7
R120
R128
C15
P7
32
1
Q11
C79
C7
R105
C71
R106
R23
R7
R15
1
2
34
6
5
U8
L8
R119
R127
C16
P8
32
1
Q10
C78
C8
R103
C70
R104
R24
R8
R16
DACP_CH4
RUN_CH4
VSNSP_CH4
VOUT_CH4 VOUT_CH5
DACP_CH5
RUN_CH5
VSNSP_CH5
DACP_CH6
RUN_CH6
VSNSP_CH6
VOUT_CH6
DACP_CH7
RUN_CH7
VSNSP_CH7
VOUT_CH7
1. ALL RESISTORS ARE 1% 0603.
2. ALL CAPACITORS ARE 16V 0603.
3. THE INTERMEDIATE BUS IS VDD=5.0V
1 PRODUCTION MIKE P. 01-18-2017
VIN
GND
SW
MODE RUN
VFB
VIN
GND
SW
MODE RUN
VFB
VIN
GND
SW
MODE RUN
VFB
VIN
GND
SW
MODE RUN
VFB
CUSTOMER NOTICE
B
SCALE = NONE
LTC CONFIDENTIAL
FOR CUSTOMER
USE ONLY
PCB DES.
APP ENG. www.linear.com
-
22
DEMO MANUAL DC2198A
Rev. A
SCHEMATIC DIAGRAM
LTC2980 CH8 Power Stage LTC2980 CH9 Power Stage
LTC2980 CH10 Power Stage LTC2980 CH11 Power Stage
1210
1210 1210
1210
1210 1210
1210
1210 1210
1210
1210 1210
CH8
2.0V
CH9
2.2V
CH10
2.5V
CH11
2.7V
2 1
2 1
2 1
2 1
LTC3405AES6
4.7uH
100k
470
10u/10V
GND
VDD GREEN
Si1308EDL
22u/10V
220p
GND GND
GND
301k
100n
100
GND
GND
VDD
3.01k
100k
66.5k
GND
LTC3405AES6
4.7uH
100k
470
10u/10V
GND
VDD GREEN
Si1308EDL
22u/10V
220p
GND GND
GND
274k
100n
100
GND
GND
VDD
3.01k
100k
57.6k
GND
LTC3405AES6
4.7uH
100k
470
10u/10V
GND
VDD GREEN
Si1308EDL
22u/10V
220p
GND GND
GND
243k
100n
100
GND
GND
VDD
3.01k
100k
47.5k
GND
LTC3405AES6
4.7uH
100k
470
10u/10V
GND
VDD GREEN
Si1308EDL
22u/10V
220p
GND GND
GND
226k
100n
100
GND
GND
VDD
3.01k
100k
42.2k
GND
1
2
34
6
5
U13
L10
R81
R73
C27
P9
32
1
Q8
C54
C38
R97
C62
R96
R39
R58
R48
1
2
34
6
5
U14
L11
R80
R72
C28
P10
32
1
Q7
C53
C39
R95
C61
R94
R40
R59
R49
1
2
34
6
5
U15
L12
R79
R71
C29
P11
32
1
Q6
C52
C40
R93
C60
R92
R41
R60
R50
1
2
34
6
5
U16
L13
R78
R70
C30
P12
32
1
Q5
C51
C41
R91
C59
R90
R42
R61
R51
VOUT_CH8
DACP_CH8
RUN_CH8
VSNSP_CH8
VOUT_CH9
DACP_CH9
RUN_CH9
VSNSP_CH9
VOUT_CH10
DACP_CH10
RUN_CH10
VSNSP_CH10
VOUT_CH11
DACP_CH11
RUN_CH11
VSNSP_CH11
1. ALL RESISTORS ARE 1% 0603.
2. ALL CAPACITORS ARE 16V 0603.
3. THE INTERMEDIATE BUS IS VDD=5.0V
1 PRODUCTION MIKE P. 01-18-2017
VIN
GND
SW
MODE RUN
VFB
VIN
GND
SW
MODE RUN
VFB
VIN
GND
SW
MODE RUN
VFB
VIN
GND
SW
MODE RUN
VFB
CUSTOMER NOTICE
B
SCALE = NONE
LTC CONFIDENTIAL
FOR CUSTOMER
USE ONLY
PCB DES.
APP ENG. www.linear.com
-
23
DEMO MANUAL DC2198A
Rev. A
SCHEMATIC DIAGRAM
LTC2980 CH12 Power Stage LTC2980 CH13 Power Stage
LTC2980 CH14 Power Stage LTC2980 CH15 Power Stage
1210
1210 1210
1210
1210 1210
1210
1210 1210
1210
1210 1210
CH12
3.0V
CH13
3.1V
CH14
3.2V
CH15
3.3V
2 1
2 1
2 1
2 1
LTC3405AES6
4.7uH
100k
470
10u/10V
GND
VDD GREEN
Si1308EDL
22u/10V
220p
GND GND
GND
205k
100n
100
GND
GND
VDD
3.01k
100k
36.5k
GND
LTC3405AES6
4.7uH
100k
470
10u/10V
GND
VDD GREEN
Si1308EDL
22u/10V
220p
GND GND
GND
196k
100n
100
GND
GND
VDD
3.01k
100k
34.8k
GND
LTC3405AES6
4.7uH
100k
470
10u/10V
GND
VDD GREEN
Si1308EDL
22u/10V
220p
GND GND
GND
191k
100n
100
GND
GND
VDD
3.01k
100k
33.2k
GND
LTC3405AES6
4.7uH
100k
470
10u/10V
GND
VDD GREEN
Si1308EDL
22u/10V
220p
GND GND
GND
182k
100n
100
GND
GND
VDD
3.01k
100k
32.4k
GND
1
2
34
6
5
U17
L14
R77
R69
C31
P13
32
1
Q4
C50
C42
R89
C58
R88
R43
R62
R52
1
2
34
6
5
U18
L15
R76
R68
C32
P14
32
1
Q3
C49
C43
R87
C57
R86
R44
R63
R53
1
2
34
6
5
U19
L16
R75
R67
C33
P15
32
1
Q2
C48
C44
R85
C56
R84
R45
R64
R54
1
2
34
6
5
U20
L17
R74
R66
C34
P16
32
1
Q1
C47
C45
R83
C55
R82
R46
R65
R55
VOUT_CH12
DACP_CH12
RUN_CH12
VSNSP_CH12
DACP_CH13
RUN_CH13
VSNSP_CH13
VOUT_CH13
VOUT_CH14
DACP_CH14
RUN_CH14
VSNSP_CH14
DACP_CH15
RUN_CH15
VSNSP_CH15
VOUT_CH15
1. ALL RESISTORS ARE 1% 0603.
2. ALL CAPACITORS ARE 16V 0603.
3. THE INTERMEDIATE BUS IS VDD=5.0V
1 PRODUCTION MIKE P. 01-18-2017
VIN
GND
SW
MODE RUN
VFB
VIN
GND
SW
MODE RUN
VFB
VIN
GND
SW
MODE RUN
VFB
VIN
GND
SW
MODE RUN
VFB
CUSTOMER NOTICE
B
SCALE = NONE
LTC CONFIDENTIAL
FOR CUSTOMER
USE ONLY
PCB DES.
APP ENG. www.linear.com
-
24
DEMO MANUAL DC2198A
Rev. A
SCHEMATIC DIAGRAM
RESET
CREATE FAULT BUTTON
CREATE_FAULT
CRA06S
CRA06S
2 1
2 1
GND
RED 698
RED
698
SN74LVC2G34DCK
GND
1u
GND
GND GND
VDD VDD
+3V3
+3V3
10n
GND
VDD
100k
GND
Si1308EDL
GND
10k, 4X
10k, 4X
100n
100n 100n
100n 100n
+3V3
+3V3
GND
100n
GND
GND GND
100n
100n
LTC2980CY
LED1 R26
LED2
R27
1
2
3 4
5
6
U24
C66
C22
R29
32
1
Q9
R136
R137
C88
C86 C89
C92 C93
C87
C90
C91
U10
G05
H06
F06
G06
B01
E05
D06
E06
F05
C01
A06
A05
C06
B06
D01
B05
C05
D05
C04
J01
B04
A04
E04
D04
H01
C02
B02
A03
B03
E01
E02
F02
C03
D03
M01
A02
A01
E03
D02
L01
G02
G01
K01
H02
J02
K02
M02
L02
K03
L03
M03
L04
K04
M04
M05
M06
L05
L06
K06
K05
J06
J05
H05
G11
H12
F12
G12
B07
E11
D12
E12
F11
C07
A12
A11
C12
B12
D07
B11
C11
D11
C10
J07
B10
A10
E10
D10
H07
C08
B08
A09
B09
E07
E08
F08
C09
D09
M07
A08
A07
E09
D08
L07
G08
G07
K07
H08
J08
K08
M08
L08
K09
L09
M09
L10
K10
M10
M11
M12
L11
L12
K12
K11
J12
J11
H11
F01
F03
F04
G03
G04
H03
H04
J03
F07
F09
F10
G09
G10
H10
J09
J10
J04
H09
GND
GND
GND
GND
RESETB
RESETB RESETB
FAULTB
FAULTB FAULTB
ALERTB
ALERTB ALERTB
VSNSP_CH0
DACP_CH0
RUN_CH0
VSNSP_CH1
VSNSP_CH2
VSNSP_CH3
VSNSP_CH4
VSNSP_CH5
VSNSP_CH6
VSNSP_CH7
DACP_CH1
DACP_CH2
DACP_CH3
DACP_CH4
DACP_CH5
DACP_CH6
DACP_CH7
RUN_CH1
RUN_CH2
RUN_CH3
RUN_CH4
RUN_CH5
RUN_CH6
RUN_CH7
VSNSP_CH8
VSNSP_CH9
VSNSP_CH10
VSNSP_CH11
VSNSP_CH12
VSNSP_CH13
VSNSP_CH14
VSNSP_CH15
DACP_CH8
DACP_CH9
DACP_CH10
DACP_CH11
DACP_CH12
DACP_CH13
DACP_CH14
RUN_CH8
RUN_CH10
RUN_CH11
RUN_CH12
RUN_CH13
RUN_CH14
RUN_CH15
RUN_CH9
DACP_CH15
SHARE_CLK
SHARE_CLK
SDA SDA
SCL SCL
CTRL CTRL
FAULT
VOUT_CH10
1. ALL RESISTORS ARE 1% 0603.
2. ALL CAPACITORS ARE 16V 0603.
3. THE INTERMEDIATE BUS IS VDD=5.0V
1 PRODUCTION MIKE P. 01-18-2017
1Y1A
2A
GND VCC
2Y
CUSTOMER NOTICE
B
SCALE = NONE
LTC CONFIDENTIAL
FOR CUSTOMER
USE ONLY
PCB DES.
APP ENG. www.linear.com
-
VDACM0
VSENSEM0
VSENSEM6
VSENSEP7
VSENSEM7
VOUT_ENO
VOUT_EN1
VOUT_EN2
VOUT_EN4
VOUT_EN5
VOUT_EN6
VOUT_EN7
VIN_EN
VIN_SNS
VPWR
AVDD33
DVDD33
VDD25
WP
VDACP1
ASEL1
VSENSEP0
VOUT_EN3
VDACP0
VSENSEP2
VDACM2
VSENSEP3
VDACM1
VSENSEP1
VSENSEM1
VDACP2
VSENSEM2
VDACM4
VSENSEM4
VDACP5
VSENSEM3
VDACP3
VDACM3
VSENSEP4
VDACP4
VSENSEP5
VDACM7
VSENSEP6
VDACM5
VDACM6
VDACP6
VDACP7
VSENSEM5
PWRGD
SHARE_CLK
FAULTB00
FAULTB01
FAULTB10
FAULTB11
SDA
SCL
ALERTB
ASEL0
CONTROL0
CONTROL1
WDI/RESETB
REFP
REFM
VDACM0
VSENSEM0
VSENSEM6
VSENSEP7
VSENSEM7
VOUT_ENO
VOUT_EN1
VOUT_EN2
VOUT_EN4
VOUT_EN5
VOUT_EN6
VOUT_EN7
VIN_EN
VIN_SNS
VPWR
AVDD33
DVDD33
VDD25
WP
VDACP1
ASEL1
VSENSEP0
VOUT_EN3
VDACP0
VSENSEP2
VDACM2
VSENSEP3
VDACM1
VSENSEP1
VSENSEM1
VDACP2
VSENSEM2
VDACM4
VSENSEM4
VDACP5
VSENSEM3
VDACP3
VDACM3
VSENSEP4
VDACP4
VSENSEP5
VDACM7
VSENSEP6
VDACM5
VDACM6
VDACP6
VDACP7
VSENSEM5
PWRGD
SHARE_CLK
FAULTB00
FAULTB01
FAULTB10
FAULTB1
1
SDA
SCL
ALERTB
ASEL0
CONTROL0
CONTROL1
WDI/RESETB
REFP
REFM
A B
A B
GND
GND
GND
GND
GND
GND
DNC
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
DNC
25
DEMO MANUAL DC2198A
Rev. A
Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog
Devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. Specifications
subject to change without notice. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
IHLP-1616BZ
CRA06S
1210 7343
1210
1210
1210
6-14V
POW ER INPUT
RUN
OFF
2 1
TDA04H0SK1
CONN_DC1613
CONTROL
GNDGND
GND GND GND
GND
24AA02T-I/OT
GND GND
1u
10k 10k
GND
MCP23008-E/ML
GND
GND
GND
1u
10k, 4X
10k
+3V3
+3V3
10u/10V
GND
LTC4313CMS8
100n
GND
GND
249
1u
GND
MALE
FEMALE
+3V3
10k
+12V
10k 10k
+3V3
GND
OPT
VDD
2.2uH
LTC3604IUD
68p
GND
4.7p
GND GND
68p
47p
GND GND
47u/16V
GND
10u/25V
GND
GND GND
100n
4.7u
GND
22u/10V
73.2k
73.2k
10k
LTC4415IMSE
GND
46.4k
10k
GND
249
GND
1.0k
GND
1u
GND
10u/10V
GND
1u
GND
GREEN
3.01k
GND
LT6654BMPS6-1.25 1u
GND GND
4.7u
2.49k
GND
BAT30CW FILM
+3V3
10k
5
6
7
81
2
3
4
JP3
1
3
2
1
2
3
4
5
6
7
8
9
10
11
12
J2
2
3
1
S1
5
6
4
S1
1
2
3 4
5
U22 C35
R57 R47
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
PAD
U21
C37
R37
R56
C46
1
2
3
4 5
6
7
8
U12
C26
R38
C36
TP11
TP12
1 2
3 4
5 6
7 8
9 10
11 12
13 14
JP2
12
34
56
78
910
1112
1314
JP1
R135
TP1
R100 R99
TP2
TP22
TP21
TP19
TP14
TP13
R31
TP20
L9
16
156
5
4
3
2
1
8
7 14
13
12
11
10
9
PAD
U9
C69
C68
C20
C23
C65
C17
C18
C67
C21
R102
R28
R25
3
2
1
6
5
4
7
8 9
10
11
12
13
14
15
16
EXP
U11
R30
R32 R33 R34
C25
C19
C24
LED3
R35
1
2
3 4
5
6
U23 C63
C64
R101
1
3
2
D1
R98
GND
GND
EEVCC
EEVCC
EESCL
EESDA
SDA_IN
SDA_IN
SCL_IN
SCL_IN
SCL
SCL
SDA
SDA
CTRL
FAULTB
FAULTB
RESETB
RESETB
ALERTB
ALERTB
SHARE_CLK
SHARE_CLK
SHARE_CLK
+12V
UNUSED1
UNUSED2
FAULT
IBV_AUX
CTRL_P
1. ALL RESISTORS ARE 1% 0603.
2. ALL CAPACITORS ARE 16V 0603.
3. THE INTERMEDIATE BUS IS VDD=5.0V
1 PRODUCTION MIKE P. 01-18-2017
1 2 3 4
ON
+5V (100mA)
SDA
GND
SCL
+3.3V(100mA)
ALERT
GPO_1
OUTEN
GPO_2
GND
AUXSCL
AUXSDA
SCL
GND
SDA VCC
WP
A2
A1
RST\
INT
GP1
GP5
VSS
A0
NC
NC
NC
GP0
GP2
GP3
GP4
GP6
GP7
VDD
SCL
SDA
PAD
ENAB LE
SCLO
SCLI
GND
VCC
SDAO
SDAI
READ Y
RUN
TRACK/SS
MODE/SYNC
PGOOD
SW
SW
NC
BOOST
INTVCC
VON
VIN
SGND
RT
FB
ITH
VIN
PAD
IN1
IN1
EN1 STAT1
OUT1
OUT1
CLIM1
CLIM2
IN2
IN2
EN2 STAT2
WARN2
WARN1
OUT2
OUT2
GND
GND
GND
DNC
DNC
VIN
VOUT
CUSTOMER NOTICE
B
SCALE = NONE
LTC CONFIDENTIAL
FOR CUSTOMER
USE ONLY
PCB DES.
APP ENG. www.linear.com
-
SCHEMATIC DIAGRAM
26
DEMO MANUAL DC2198A
Rev. A
ANALOG DEVICES, INC. 2015-2018
10/18
www.analog.com
ESD Caution
ESD (electrostatic discharge) sensitive device. Charged devices and circuit boards can discharge without detection. Although this product features patented or proprietary protection
circuitry, damage may occur on devices subjected to high energy ESD. Therefore, proper ESD precautions should be taken to avoid performance degradation or loss of functionality.
Legal Terms and Conditions
By using the evaluation board discussed herein (together with any tools, components documentation or support materials, the “Evaluation Board”), you are agreeing to be bound by the terms and
conditions set forth below (“Agreement”) unless you have purchased the Evaluation Board, in which case the Analog Devices Standard Terms and Conditions of Sale shall govern. Do not use the Evaluation
Board until you have read and agreed to the Agreement. Your use of the Evaluation Board shall signify your acceptance of the Agreement. This Agreement is made by and between you (“Customer”)
and Analog Devices, Inc. (“ADI”), with its principal place of business at One Technology Way, Norwood, MA 02062, USA. Subject to the terms and conditions of the Agreement, ADI hereby grants to
Customer a free, limited, personal, temporary, non-exclusive, non-sublicensable, non-transferable license to use the Evaluation Board FOR EVALUATION PURPOSES ONLY. Customer understands and
agrees that the Evaluation Board is provided for the sole and exclusive purpose referenced above, and agrees not to use the Evaluation Board for any other purpose. Furthermore, the license granted
is expressly made subject to the following additional limitations: Customer shall not (i) rent, lease, display, sell, transfer, assign, sublicense, or distribute the Evaluation Board; and (ii) permit any Third
Party to access the Evaluation Board. As used herein, the term “Third Party” includes any entity other than ADI, Customer, their employees, affiliates and in-house consultants. The Evaluation Board is
NOT sold to Customer; all rights not expressly granted herein, including ownership of the Evaluation Board, are reserved by ADI. CONFIDENTIALITY. This Agreement and the Evaluation Board shall all
be considered the confidential and proprietary information of ADI. Customer may not disclose or transfer any portion of the Evaluation Board to any other party for any reason. Upon discontinuation of
use of the Evaluation Board or termination of this Agreement, Customer agrees to promptly return the Evaluation Board to ADI. ADDITIONAL RESTRICTIONS. Customer may not disassemble, decompile
or reverse engineer chips on the Evaluation Board. Customer shall inform ADI of any occurred damages or any modifications or alterations it makes to the Evaluation Board, including but not limited
to soldering or any other activity that affects the material content of the Evaluation Board. Modifications to the Evaluation Board must comply with applicable law, including but not limited to the RoHS
Directive. TERMINATION. ADI may terminate this Agreement at any time upon giving written notice to Customer. Customer agrees to return to ADI the Evaluation Board at that time. LIMITATION OF
LIABILITY. THE EVALUATION BOARD PROVIDED HEREUNDER IS PROVIDED “AS IS” AND ADI MAKES NO WARRANTIES OR REPRESENTATIONS OF ANY KIND WITH RESPECT TO IT. ADI SPECIFICALLY
DISCLAIMS ANY REPRESENTATIONS, ENDORSEMENTS, GUARANTEES, OR WARRANTIES, EXPRESS OR IMPLIED, RELATED TO THE EVALUATION BOARD INCLUDING, BUT NOT LIMITED TO, THE
IMPLIED WARRANTY OF MERCHANTABILITY, TITLE, FITNESS FOR A PARTICULAR PURPOSE OR NONINFRINGEMENT OF INTELLECTUAL PROPERTY RIGHTS. IN NO EVENT WILL ADI AND ITS
LICENSORS BE LIABLE FOR ANY INCIDENTAL, SPECIAL, INDIRECT, OR CONSEQUENTIAL DAMAGES RESULTING FROM CUSTOMER’S POSSESSION OR USE OF THE EVALUATION BOARD, INCLUDING
BUT NOT LIMITED TO LOST PROFITS, DELAY COSTS, LABOR COSTS OR LOSS OF GOODWILL. ADI’S TOTAL LIABILITY FROM ANY AND ALL CAUSES SHALL BE LIMITED TO THE AMOUNT OF ONE
HUNDRED US DOLLARS ($100.00). EXPORT. Customer agrees that it will not directly or indirectly export the Evaluation Board to another country, and that it will comply with all applicable United States
federal laws and regulations relating to exports. GOVERNING LAW. This Agreement shall be governed by and construed in accordance with the substantive laws of the Commonwealth of Massachusetts
(excluding conflict of law rules). Any legal action regarding this Agreement will be heard in the state or federal courts having jurisdiction in Suffolk County, Massachusetts, and Customer hereby submits
to the personal jurisdiction and venue of such courts. The United Nations Convention on Contracts for the International Sale of Goods shall not apply to this Agreement and is expressly disclaimed.
