54AC139,54ACT139 54AC139 54ACT139 Dual 1-of-4 Decoder/Demultiplexer Literature Number: SNOS086 54AC139 * 54ACT139 Dual 1-of-4 Decoder/Demultiplexer General Description The 'AC/'ACT139 is a high-speed, dual 1-of-4 decoder/ demultiplexer. The device has two independent decoders, each accepting two inputs and providing four mutually-exclusive active-LOW outputs. Each decoder has an active-LOW Enable input which can be used as a data input for a 4-output demultiplexer. Each half of the 'AC/ 'ACT139 can be used as a function generator providing all four minterms of two variables. n n n n n n Multifunction capability Two completely independent 1-of-4 decoders Active LOW mutually exclusive outputs Outputs source/sink 24 mA 'ACT139 has TTL-compatible inputs Standard Military Drawing (SMD) -- 'AC139: 5962-87623 -- 'ACT139: 5962-87553 Features n ICC reduced by 50% Logic Symbols IEEE/IEC DS100269-8 DS100269-2 Pin Names Description A0, A1 Address Inputs E Enable Inputs O0-O3 Outputs DS100269-1 FACT (R) is a registered trademark of Fairchild Semiconductor Corporation. (c) 1998 National Semiconductor Corporation DS100269 www.national.com 54AC139 * 54ACT139 Dual 1-of-4 Decoder/Demultiplexer August 1998 Connection Diagrams can be used as the data input for a 4-output demultiplexer application. Each half of the 'AC/'ACT139 generates all four minterms of two variables. These four minterms are useful in some applications, replacing multiple gate functions as shown in , and thereby reducing the number of packages required in a logic network. Pin Assignment for DIP and Flatpak DS100269-3 Pin Assignment for LCC DS100269-6 FIGURE 1. Gate Functions (Each Half) Truth Table Inputs DS100269-4 Functional Description The 'AC/'ACT139 is a high-speed dual 1-of-4 decoder/ demultiplexer. The device has two independent decoders, each of which accepts two binary weighted inputs (A0-A1) and provides four mutually exclusive active-LOW outputs (O0-O3). Each decoder has an active-LOW enable (E). When E is HIGH all outputs are forced HIGH. The enable www.national.com Outputs E A0 A1 O0 O1 O2 O3 H X X H H H H L L L L H H H L H L H L H H L L H H H L H L H H H H H L H = HIGH Voltage Level L = LOW Voltage Level X = Immaterial 2 Logic Diagram DS100269-5 Please note that this diagram is provided only for the understanding of logic operations and should not be used to estimate propagation delays. 3 www.national.com Absolute Maximum Ratings (Note 1) Recommended Operating Conditions If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/ Distributors for availability and specifications. Supply Voltage (VCC) DC Input Diode Current (IIK) VI = -0.5V VI = VCC + 0.5V DC Input Voltage (VI) DC Output Diode Current (IOK) VO = -0.5V VO = VCC + 0.5V DC Output Voltage (VO) DC Output Source or Sink Current (IO) DC VCC or Ground Current per Output Pin (ICC or IGND) Storage Temperature (TSTG) Junction Temperature (TJ) CDIP Supply Voltage (VCC) 'AC 'ACT Input Voltage (VI) Output Voltage (VO) Operating Temperature (TA) 54AC/ACT Minimum Input Edge Rate (V/t) 'AC Devices VIN from 30% to 70% of VCC VCC @ 3.3V, 4.5V, 5.5V Minimum Input Edge Rate (V/t) 'ACT Devices VIN from 0.8V to 2.0V VCC @ 4.5V, 5.5V -0.5V to +7.0V -20 mA +20 mA -0.5V to VCC + 0.5V -20 mA +20 mA -0.5V to VCC + 0.5V 50 mA 50 mA -65C to +150C 2.0V to 6.0V 4.5V to 5.5V 0V to VCC 0V to VCC -55C to +125C 125 mV/ns 125 mV/ns Note 1: Absolute maximum ratings are those values beyond which damage to the device may occur. The databook specifications should be met, without exception, to ensure that the system design is reliable over its power supply, temperature, and output/input loading variables. National does not recommend operation of FACT (R) circuits outside databook specifications. 175C DC Characteristics for 'AC Family Devices Symbol Parameter 54AC TA = VCC (V) Units Conditions -55C to +125C Guaranteed Limits VIH VIL VOH VOL IIN Minimum High Level 3.0 2.1 Input Voltage 4.5 3.15 5.5 3.85 Maximum Low Level 3.0 0.9 Input Voltage 4.5 1.35 5.5 1.65 Minimum High Level 3.0 2.9 Output Voltage 4.5 4.4 5.5 5.4 3.0 2.4 4.5 3.7 5.5 4.7 Maximum Low Level 3.0 0.1 Output Voltage 4.5 0.1 5.5 0.1 Maximum Input 3.0 0.50 4.5 0.50 5.5 0.50 5.5 1.0 Leakage Current www.national.com 4 VOUT = 0.1V V or VCC - 0.1V V or VCC - 0.1V VOUT = 0.1V IOUT = -50 A V V (Note 2) VIN = VIL or VIH IOH = -12 mA IOH = -24 mA IOH = -24 mA IOUT = 50 A V (Note 2) VIN = VIL or VIH IOL = 12 mA V A IOL = 24 mA IOL = 24 mA VI = VCC, GND DC Characteristics for 'AC Family Devices Symbol Parameter (Continued) 54AC TA = VCC (V) Units Conditions -55C to +125C Guaranteed Limits IOLD IOHD ICC (Note 3) Minimum Dynamic Output Current 5.5 50 mA 5.5 -50 mA Maximum Quiescent 5.5 80.0 A Supply Current VOLD = 1.65V Max VOHD = 3.85V Min VIN = VCC or GND Note 2: All outputs loaded; thresholds on input associated with output under test. Note 3: Maximum test duration 2.0 ms, one output loaded at a time. Note 4: IIN and ICC @ 3.0V are guaranteed to be less than or equal to the respective limit @ 5.5V VCC. ICC for 54AC @ 25C is identical to 74AC @ 25C. DC Characteristics for 'ACT Family Devices Symbol Parameter 54ACT TA = VCC (V) Units Conditions -55C to +125C Guaranteed Limits VIH VIL VOH VOL IIN Minimum High Level 4.5 2.0 Input Voltage 5.5 2.0 Maximum Low Level 4.5 0.8 Input Voltage 5.5 0.8 Minimum High Level 4.5 4.4 Output Voltage 5.5 5.4 4.5 3.70 5.5 4.70 Maximum Low Level 4.5 0.1 Output Voltage 5.5 0.1 Maximum Input V VOUT = 0.1V V or VCC - 0.1V VOUT = 0.1V V or VCC - 0.1V IOUT = -50 A V (Note 5) VIN = VIL or VIH IOH = -24 mA V IOH = -24 mA IOUT = 50 A V (Note 5) VIN = VIL or VIH IOL = 24 mA 4.5 0.50 5.5 0.50 5.5 1.0 A IOL = 24 mA VI = VCC, GND 5.5 1.6 mA VI = VCC - 2.1V VOLD = 1.65V Max VOHD = 3.85V Min Leakage Current ICCT Maximum ICC/Input (Note 6) IOLD Minimum Dynamic 5.5 50 mA IOHD Output Current 5.5 -50 mA ICC Maximum Quiescent 5.5 80.0 A Supply Current VIN = VCC or GND Note 5: All outputs loaded; thresholds on input associated with output under test. Note 6: Maximum test duration 2.0 ms, one output loaded at a time. Note 7: ICC for 54ACT @ 25C is identical to 74ACT @ 25C. 5 www.national.com AC Electrical Characteristics 54AC TA = -55C VCC Symbol Parameter (V) to +125C CL = 50 pF (Note 8) tPLH tPHL tPLH tPHL Min Max Propagation Delay 3.3 1.0 14.5 An to On 5.0 1.0 11.0 Propagation Delay 3.3 1.0 12.5 An to On 5.0 1.0 10.0 Propagation Delay 3.3 1.0 14.5 En to On 5.0 1.0 11.0 Propagation Delay 3.3 1.0 12.5 En to On 5.0 1.0 10.0 Fig. Units No. ns ns ns ns Note 8: Voltage Range 3.3 is 3.3V 0.3V Voltage Range 5.0 is 5.0V 0.5V AC Electrical Characteristics 54ACT TA = -55C VCC Symbol Parameter (V) to +125C CL = 50 pF (Note 9) tPLH Propagation Delay Fig. Units Min Max 5.0 1.0 12.0 ns 5.0 1.0 11.0 ns 5.0 1.0 12.5 ns 5.0 1.0 12.0 ns An to On tPHL Propagation Delay An to On tPLH Propagation Delay En to On tPHL Propagation Delay En to On Note 9: Voltage Range 5.0 is 5.0V 0.5V Capacitance Symbol CIN CPD Typ Units Input Capacitance Parameter 4.5 pF Power Dissipation 40.0 pF Capacitance www.national.com 6 Conditions VCC = OPEN VCC = 5.0V No. Physical Dimensions inches (millimeters) unless otherwise noted 20 Terminal Ceramic Leadless Chip Carrier (L) NS Package Number E20A 16 Lead Ceramic Dual In-Line Package (D) NS Package Number J16A 7 www.national.com 54AC139 * 54ACT139 Dual 1-of-4 Decoder/Demultiplexer Physical Dimensions inches (millimeters) unless otherwise noted (Continued) 16 Lead Ceramic Flatpak (F) NS Package Number W16A LIFE SUPPORT POLICY NATIONAL'S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein: 2. A critical component in any component of a life support 1. Life support devices or systems are devices or sysdevice or system whose failure to perform can be reatems which, (a) are intended for surgical implant into sonably expected to cause the failure of the life support the body, or (b) support or sustain life, and whose faildevice or system, or to affect its safety or effectiveness. ure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the user. National Semiconductor Corporation Americas Tel: 1-800-272-9959 Fax: 1-800-737-7018 Email: support@nsc.com www.national.com National Semiconductor Europe Fax: +49 (0) 1 80-530 85 86 Email: europe.support@nsc.com Deutsch Tel: +49 (0) 1 80-530 85 85 English Tel: +49 (0) 1 80-532 78 32 Francais Tel: +49 (0) 1 80-532 93 58 Italiano Tel: +49 (0) 1 80-534 16 80 National Semiconductor Asia Pacific Customer Response Group Tel: 65-2544466 Fax: 65-2504466 Email: sea.support@nsc.com National Semiconductor Japan Ltd. Tel: 81-3-5620-6175 Fax: 81-3-5620-6179 National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications. IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI's standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications. TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Applications Audio www.ti.com/audio Communications and Telecom www.ti.com/communications Amplifiers amplifier.ti.com Computers and Peripherals www.ti.com/computers Data Converters dataconverter.ti.com Consumer Electronics www.ti.com/consumer-apps DLP(R) Products www.dlp.com Energy and Lighting www.ti.com/energy DSP dsp.ti.com Industrial www.ti.com/industrial Clocks and Timers www.ti.com/clocks Medical www.ti.com/medical Interface interface.ti.com Security www.ti.com/security Logic logic.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Power Mgmt power.ti.com Transportation and Automotive www.ti.com/automotive Microcontrollers microcontroller.ti.com Video and Imaging RFID www.ti-rfid.com OMAP Mobile Processors www.ti.com/omap Wireless Connectivity www.ti.com/wirelessconnectivity TI E2E Community Home Page www.ti.com/video e2e.ti.com Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2011, Texas Instruments Incorporated