EVALUATION KIT AVAILABLE MAX31910 Ultra-Low Power Industrial, Octal, Digital Input Translator/Serializer General Description The MAX31910 industrial interface serializer translates, conditions, and serializes the 24V digital output of sensors and switches used in industrial, process, and building automation to 5V CMOS-compatible signals required by microcontrollers. It provides the front-end interface circuit of a programmable logic controller (PLC) digital input module. The device features integrated current limiting, lowpass filtering, and channel serialization. Input current limiting allows a significant reduction in power consumed from the field voltage supply as compared to traditional discrete resistor-divider implementations. In addition, to achieve the lowest in-class power dissipation, the device uses patent-pending circuit techniques to achieve further reduction of power beyond what is possible by input current limiting alone. Selectable on-chip lowpass filters allow flexible debouncing and filtering of sensor outputs based on the application. On-chip serialization allows a drastic reduction in the number of optocouplers used for isolation. The device serializer is stackable so that any number of input channels can be serialized and output through only one SPIcompatible port. This reduces the number of optocouplers needed to only three, regardless of the number of input channels. For enhanced robustness with respect to high-frequency noise and fast electrical transients, a multibit CRC code is generated and transmitted through the SPI port for each 8 bits of data. The on-chip 5V voltage regulator can be used to power external optocouplers, digital isolators, or other external 5V circuitry. For low-cost applications, Maxim Integrated offers a pin-compatible version of this device, the MAX31911. The MAX31911 does not include the patent-pending current clamp-switching circuitry that is included with the MAX31910. The MAX31912 and MAX31913 versions includes energyless LED drivers while maintaining pin compatibility. Ordering Information appears at end of data sheet. 19-6440; Rev 5; 4/15 Benefits and Features Ultra-Low Power and Heat Dissipation * Low Quiescent Current (1.4mA typ) * Highly Accurate and Stable Input Current Limiters, Adjustable from 0.5mA to 6mA * Special (Patent-Pending) Ultra-Low-Power Mode with Switched Current Limiters High Integration Reduces BOM Count, Board Size, and System Cost * 8 High-Voltage Input Channels (36V max) * On-Chip 8-1 Serialization with SPI Interface * On-Chip 5V Regulator * On-Chip Overtemperature Indicator * On-Chip Field Supply Voltage Monitor * Integrated Debounce Filters, Selectable from 0 to 3ms Robust Features and Performance for Industrial Environments * Multibit CRC Code Generation and Transmission for Error Detection and More Reliable Data Transmission * High ESD Immunity on All Field Input Pins Accepts Industry Standard Input Types * Configurable for IEC 61131-2 Input Types 1, 2, and 3 Flexible Power Supply Capability Enables Usage in 5V, 12V, 24V, and Higher Voltage Systems * Wide Operating Field Supply Range of 7V to 36V * Can Be Powered From the Logic-Side Using a 5V Supply Applications Digital Input Modules for PLCs Industrial, Building, and Process Automation Motor Control MAX31910 Ultra-Low Power Industrial, Octal, Digital Input Translator/Serializer Block Diagram 24V VCC24V 5VOUT 5V REGULATOR SUPPLY MONITOR MAX31910 VREF OR TEMP MONITOR RIREF RT1 CRC GEN. LP FILTER SENSORS VREF IN8 GND www.maximintegrated.com SIN CONTROLLER OR ISOLATION MODESEL VOLTAGE COMPARATOR CLK INPUT CHANNEL 0 RT8 FAULTB DB0 DB1 SWITCHED CURRENT LIMITER IN1 5V INPUT CHANNEL 7 SERIALIZER CS SOUT Maxim Integrated 2 MAX31910 Ultra-Low Power Industrial, Octal, Digital Input Translator/Serializer Absolute Maximum Ratings (Voltages relative to GND.) Voltage Range on VCC24V.............................. -0.3V to +45V Voltage Range on IN1-IN8............................. -0.3V to +45V Voltage Range on IN1-IN8 (through 2.2k resistors)............................. -45V to +45V Voltage Range on DB0/DB1, CLK, SIN, CS, MODESEL........................... -0.3V to (V5VOUT + 0.3V) Continuous Power Dissipation (TA = +70NC) TSSOP (derate 27mW/NC above +70NC)........... 2162.2mW Operating Temperature Range Ambient Temperature............................. -40NC to +125NC Junction Temperature............................. -40NC to +150NC Storage Temperature Range....................... -55NC to +125NC Lead Temperature (soldering, 10s)..........................+300NC Soldering Temperature (reflow)................................+260NC Stresses beyond those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. Package Thermal Characteristics (Note 1) TSSOP Junction-to-Ambient Thermal Resistance (qJA)...........37C/W Junction-to-Case Thermal Resistance (qJC)...................2C/W Note 1: Package thermal resistances were obtained using the method described in JEDEC specification JESD51-7, using a four-layer board. For detailed information on package thermal considerations, refer to www.maximintegrated.com/thermal-tutorial. Recommended Operating Conditions (Note 2) PARAMETER SYMBOL Field Supply Voltage VCC24V Field Inputs Voltage VINn Logic Inputs Voltage VLOGIC Current-Limit Setting Resistor Field Input Data Rate www.maximintegrated.com CONDITIONS (Note 3) RREF fIN (Note 4) MIN TYP MAX UNITS 7 36 V -0.3 36 V 0 5.5 V 15 kI 200 kHz Maxim Integrated 3 MAX31910 Ultra-Low Power Industrial, Octal, Digital Input Translator/Serializer DC Electrical Characteristics (VCC24V = 7V to 36V, TJ = -40NC to +150NC, unless otherwise noted.) (Note 2) PARAMETER Field-Supply Current SYMBOL CONDITIONS ICC24V IN1-IN8 = 24V, 5VOUT = open, RT1-RT8 = GND, all logic inputs open MIN TYP MAX UNITS 1.4 2.2 mA 9 10 V Field-Supply UVLO Off/On VONUVLO Field-Supply UVLO On/Off VOFFUVLO Field Input Threshold Highto-Low VIN-(INF) 2.2kI external series resistor Field Input Threshold Low-toHigh VIN+(INF) 2.2kI external series resistor (Note 11) 8.5 Field Input Hysteresis VHYS(INF) 2.2kI external series resistor (Note 11) 1 V Input Threshold High-to-Low (at IC pin) VTH-(INP) 2.5 V Input Threshold Low-to-High (at IC pin) VTH+(INP) (Note 11) 3.5 Input Threshold Hysteresis (at IC pin) VHYS(INP) (Note 11) 1 V Field Input Pin Resistance RINP 0.8 kI Field Input Current Limit Filter Time Constant Linear Regulator Output 8 V 6 7.5 V 2 IINLIM RREF = 15kI, VCC24V = 18V to 30V (Note 5) tFILTER V5VOUT 7 10 4 2.2 2.4 2.6 DB1/DB0 = 0/0: no filtering DB1/DB0 = 0/1 DB1/DB0 = 1/0 DB1/DB0 = 1/1 0.008 0.25 1.0 0 0.025 0.75 3 0.038 1.1 4.5 Max ILOAD = 50mA 4.75 V V mA ms 5.0 5.25 V Regulator Line Regulation dVREGLINE ILOAD = 50mA 10 20 mV Regulator Load Regulation dVREGLOAD ILOAD = 1mA to 50mA 20 50 mV 0.4 1.0 V Logic-Low Output Voltage VOL IOL = 4mA Logic-High Output Voltage VOH IOH = -4mA Logic-Input Trip Point VIH-IL 0.3 x V5VOUT 0.5 x V5VOUT 0.7 x V5VOUT V IIL -50 -30 -15 FA Logic-Input Leakage Current Overtemperature Alarm www.maximintegrated.com TALRM 4.0 V 135 NC Maxim Integrated 4 MAX31910 Ultra-Low Power Industrial, Octal, Digital Input Translator/Serializer AC Electrical Characteristics (VCC24V = 7V to 36V, TJ = -40NC to +150NC, unless otherwise noted.) (Note 2) PARAMETER Field Input Pulse Width SYMBOL tPW ESD CONDITIONS No external capacitors on pins IN1IN8 MIN TYP MAX UNITS s 1 HBM, all pins 2 HBM, IN1-IN8 with respect to GND 15 kV AC Electrical Characteristics: SPI Interface (VCC24V = 7V to 36V, TJ = -40NC to +150NC, unless otherwise noted.) (Note 2) PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS CLK Pulse Duration tCLKPW (Note 6) 20 ns CS Pulse Duration tCSPW (Note 7) 20 ns SIN to CLK Setup Time tSU1 (Note 8) 5 ns SIN to CLK Hold Time tH1 (Note 8) 8 ns CS to CLK Setup Time tSU2 (Note 9) 8 ns CS to CLK Recovery Time tREC (Note 9) 12 ns Clock Pulse Frequency fCLK (Notes 6, 10) 25 MHz Propagation Delay, CLK to SOUT tP1 (Note 6) 20 ns Propagation Delay, CS to SOUT tP2 (Note 7) 20 ns Rise/Fall Time SOUT/FAULT tR/F (Note 6) 40 ns Note 2: Limits are 100% production tested at TA = +25C and/or TA = +125C. Limits over the operating temperature range and relevant supply voltage range are guaranteed by design and characterization. Typical values are not guaranteed. Note 3: When using suggested external 2.2k series resistors, limits of -3V to +36V apply. Note 4: fIN refers to the maximum pulse frequency (1/fIN = shortest pulse width) that can be detected from the field sensors and switches. Note 5: External resistor RREF can be adjusted to set any desired current limit between 0.5mA and 6mA. Note 6: See Figure 9. Note 7: See Figure 6. Note 8: See Figure 8. Note 9: See Figure 7. Note 10: This is the maximum bit transfer rate through the serializer interface. Note 11: When input current switching is enabled (DB0/DB1 = 0), there is no input threshold hysteresis. In this case, the input threshold for both falling and rising signals is the high-to-low threshold. www.maximintegrated.com Maxim Integrated 5 MAX31910 Ultra-Low Power Industrial, Octal, Digital Input Translator/Serializer Typical Operating Characteristics (TA = +25C, RREF = 15k, unless otherwise noted.) POWER-SUPPLY CURRENT vs. VCC24V FIELD SUPPLY 1.45 1.40 1.55 1.50 1.45 5 0 60 10 INPUT VOLTAGE HYSTERESIS vs. TEMPERATURE 2.5 2.3 2.2 2.0 1.5 1.0 RIN = 0I 3.8 3.6 3.4 3.2 OFF-ON THRESHOLD 3.0 2.8 2.6 2.4 0.5 2.1 ON-OFF THRESHOLD 2.2 2.0 10 -40 60 0 110 2.0 5 15 AMBIENT TEMPERATURE (C) INPUT VOLTAGE HYSTERESIS vs. TEMPERATURE 35 -40 LDO LOAD REGULATION 7.0 7.8 7.6 ON-OFF THRESHOLD 7.0 5.06 5.04 5.02 5.00 4.98 4.96 60 TEMPERATURE (C) www.maximintegrated.com 110 I5VOUT = 5mA 5.08 5.06 5.04 5.02 5.00 4.98 4.96 4.94 4.94 4.92 4.92 4.90 10 110 LDO LINE REGULATION 5VOUT VOLTAGE (V) OFF-ON THRESHOLD 60 5.10 MAX31910 toc08 5.08 5VOUT VOLTAGE (V) 8.4 -40 10 TEMPERATURE (C) 5.10 MAX31910 toc07 RIN = 2.2I 8.6 7.2 25 FIELD INPUT VOLTAGE (V) 9.0 MAX31910 toc06 VCC24V = 24V MAX31910 toc09 2.4 4.0 MAX31910 toc05 3.0 THRESHOLD VOLTAGE (V) 2.5 7.4 40 INPUT CURRENT LIMIT vs. FIELD INPUT VOLTAGE 2.6 8.2 30 INPUT CURRENT LIMIT vs. TEMPERATURE 2.7 8.8 20 RREF (kI) CURRENT LIMIT (mA) CURRENT LIMIT (mA) 10 -40 TEMPERATURE (C) 2.8 THRESHOLD VOLTAGE (V) 2.5 SUPPLY VOLTAGE (V) VINn = 24V 2.9 3.5 0.5 1.40 35 25 MAX31910 toc04 3.0 15 4.5 1.5 1.35 1.30 MAX31910 toc03 5.5 CURRENT LIMIT (mA) SUPPLY CURRENT (mA) 1.50 MAX31910 toc02 1.60 MAX31910 toc01 1.55 SUPPLY CURRENT (mA) CURRENT LIMIT vs. RREF SUPPLY CURRENT vs. TEMPERATURE 1.60 4.90 0 10 20 30 40 5VOUT OUTPUT CURRENT (mA) 50 6 11 16 21 26 31 36 SUPPLY VOLTAGE (V) Maxim Integrated 6 MAX31910 Ultra-Low Power Industrial, Octal, Digital Input Translator/Serializer Typical Operating Characteristics (continued) (TA = +25C, RREF = 15k, unless otherwise noted.) LDO OUTPUT vs. VCC24V FIELD SUPPLY LDO LINE REGULATION 5.04 5.02 5.00 4.98 4.96 5.3 5.2 5.1 5.0 4.9 4.8 4.94 4.7 4.92 4.6 4.5 4.90 11 6 16 21 26 31 14 24 SUPPLY VOLTAGE (V) SUPPLY VOLTAGE (V) LDO OUTPUT VOLTAGE vs. TEMPERATURE LDO OUTPUT VOLTAGE vs. TEMPERATURE 5.06 5.02 5.00 4.98 4.96 5.06 5.04 5.02 5.00 4.98 4.96 4.94 4.94 4.92 4.92 4.90 I5VOUT = 5mA 5.08 5VOUT VOLTAGE (V) 5.04 34 5.10 MAX31910 toc12 I5VOUT = 0mA 5.08 4 36 5.10 5VOUT VOLTAGE (V) I5VOUT = 50mA 5.4 MAX31910 toc13 5VOUT VOLTAGE (V) 5.06 5.5 MAX31910 toc11 I5VOUT = 50mA 5.08 5VOUT OTPUT VOLTAGE (V) MAX31910 toc10 5.10 4.90 -40 10 60 AMBIENT TEMPERATURE (C) www.maximintegrated.com 110 -40 10 60 110 AMBIENT TEMPERATURE (C) Maxim Integrated 7 MAX31910 Ultra-Low Power Industrial, Octal, Digital Input Translator/Serializer Pin Configuration TOP VIEW + DB0 1 28 GND DB1 2 27 SIN IN1 3 26 MODESEL RT1 4 25 CLK IN2 5 24 CS RT2 6 23 SOUT IN3 7 22 IN8 RT3 8 21 RT8 MAX31910 IN4 9 20 IN7 RT4 10 19 RT7 IN5 11 18 IN6 RT5 12 17 RT6 RIREF 13 16 FAULT VCC24V 14 15 5VOUT EP Pin Description PIN NAME 1, 2 DB0, DB1 3, 5, 7, 9, 11, 18, 20, 22 IN1-IN8 Field Inputs 4, 6, 8, 10, 12, 17, 19, 21 RT1-RT8 Connect directly to GND. These pins are reserved for energy-less LED drivers in future versions of the device. 13 RIREF 14 VCC24V Field-Supply Voltage 15 5VOUT 5V Regulator Output 16 FAULT Active-Low Overtemperature or Undervoltage Alarm 23 SOUT Serial-Data Out 24 CS 25 CLK 26 MODESEL 27 SIN 28 GND -- EP www.maximintegrated.com FUNCTION Debounce (Filtering) Time Select Inputs. These inputs also determine the current switching frequency. See Table 1 for details. Current-Limiter Reference Resistor Active-Low Chip-Select Input Serial-Clock Input Mode-Select Input MODESEL = 1: Selects 8-bit shift register MODESEL = 0: Selects 16-bit shift register Serial-Data Input Field Ground Exposed Pad. Must be connected to the PCB ground plane. Maxim Integrated 8 MAX31910 Ultra-Low Power Industrial, Octal, Digital Input Translator/Serializer Basic Application Circuit 24V JUMPERS TO 5VOUT AND GND R1 5VOUT VCC24V DB0 C1 C4 DB1 VDD_LOGIC MODESEL SIN RINX fIN1-8 MAX31910 CLK IN1-8 CLK CS CS ISOLATION RT1-8 SOUT SOUT FAULT FAULT GND RIREF RREF NOTE: SEE FIGURE 1 FOR ADDITIONAL COMPONENTS NEEDED FOR EMC. Detailed Description Input Current Clamp The MAX31910 industrial interface serializer inputs (IN1- IN8) sense the state (on vs. off) of field sensors by monitoring both voltage and current flowing through the sensor output. The current sinking through these input pins rises linearly with input voltage until the limit set by the current clamp is reached. Any voltage increase beyond this point does not increase the input current any further. The value of the current clamp is adjustable through an external resistor connected between the RIREF pin and GND. Pins RT1-RT8 must be connected directly to GND to provide a return path for the input current. The voltage and current at the IN1-IN8 input pins are compared against internally set references to determine whether the sensor is on (logic 1) or off (logic 0). The trip points determining the on/off status of the sensor satisfy the requirements of IEC 61131-2 Type 1 and 3 switches. The device can also be configured to work as a Type 2 switch. www.maximintegrated.com Glitch Filter A digital glitch filter provides debouncing and filtering of noisy sensor signals. The time constant of this filter is programmable from 0ms to 3ms through the DB0 and DB1 pins. See Table 1 for debounce settings. To provide the digital glitch filter, the device checks that an input is stable for at least three clock cycles. The duration of a clock cycle is 1/3 of the selected debounce time. If the input is not stable for at least three clock cycles, the input change is not sent to the internal shift register. Low-Power Current Clamp Switching The MAX31910 uses a patent-pending switched current limiter to reduce power consumption below what is achievable by current limiting alone (Figure 1). The internal filter clock is used to switch input current between 100% and 20% of the chosen current limit. For example, if the current limit is set to 2.4mA, the input current switches between 2.4mA and 0.48mA. The switching is done at a controlled ramp rate of tDELAY (0.5s typ). The filter clock switches input current at a 50% duty cycle. The clock period for current switching is automatically selected by the DB1 and DB0 glitch filter settings. See Table 1 for current switching settings. Maxim Integrated 9 MAX31910 Ultra-Low Power Industrial, Octal, Digital Input Translator/Serializer 24V SENSOR OUTPUT VOLTAGE tDELAY 0V tDELAY 100% ILIMIT INPUT CURRENT LIMIT 20% ILIMIT INTERNAL FILTER CLOCK TIME COMPARATOR OUTPUT IS LATCHED INTO FILTER ON RISING EDGE OF CLOCK Figure 1. Operation of Patent-Pending Switched Current Limiter Table 1. Debounce Settings DB1 DB0 BINARY VALUE DEBOUNCE TIME CURRENT SWITCHING PERIOD 0 0 0 1 0 0 DC (disabled) 1 25Fs 8Fs 1 1 0 2 0.75ms 0.25ms 1 3 3ms 1ms Powering the Device Through the 5VOUT Pin Reading Serial Data The device can alternatively be powered using a 5V supply connected to the 5VOUT pin. In this case a 24V supply is no longer needed and the VCC24V supply must be kept unconnected (see Figure 2). The filtered outputs of the input comparators are latched into a shift register at the falling edge of CS. Clocking the CLK pin, while CS is held low, shifts the latched data out of SOUT 1 bit at a time. In this configuration, the device will always indicate a UVFAULT and the FAULT pin will always be active (pulled low). Faults due to the supply voltage monitoring will not be available. Faults due to the temperature monitor can only be read through the SPI interface. The internal data serializer comprises a 16-bit shift register, containing 8 bits of data corresponding to the eight field inputs, as well as an 8-bit status byte containing supplementary status and CRC information. The status byte contains 1 bit representing the status of the field-supply voltage (UV), 1 bit representing the status of the internal temperature monitor (OT), a 5-bit CRC code internally calculated and generated, and a trailing 1 as a STOP bit. This configuration has a lower power consumption and heat dissipation since the on-chip 5V voltage regulator is disabled. The undervoltage (UV) bit is normally 0. If the supply voltage falls below VOFFUVLO, the UV becomes a 1. The UV bit returns to 0 once the supply voltage has returned above VONUVLO. www.maximintegrated.com Maxim Integrated 10 MAX31910 Ultra-Low Power Industrial, Octal, Digital Input Translator/Serializer JUMPERS TO 5V AND GND NOT CONNECTED 5VOUT DB0 DB1 VCC24V MODESEL FIN1-8 RINX C3 5V C1 SIN MAX31910 IN1-8 CLK CS SOUT RT1-8 FAULT RIREF GND RREF Figure 2. Basic Application Powered Through 5VOUT The overtemperature (OT) bit is also normally 0. If the junction temperature increases to above TALRM, the OT bit becomes a 1. The bit returns to 0 once the junction temperature has returned below TALRM. The CRC code can be used to check data integrity during transfer from the device to an external microcontroller. In applications where the integrity of data transferred is not of concern, the CRC bits can be ignored. The CRC uses the following polynomial: P(x) = x5 + x4 + x2 + x0 The number of bits in the internal serializer can be selected between 8 bits or 16 bits. The MODESEL pin is used to configure the serializer as an 8-bit (disabling the status byte) or 16-bit shift register. In 8-bit mode, only the eight field input states are transferred through the SPI port and the status byte is ignored. Therefore, in multiple IC applications (input channels greater than 8), if desired, only a single status byte can be generated and transmitted for any number of input channels. The shift register contents are read only (no write capability exists) through the SPI-compatible interface. For higher input counts than 8, multiple devices can be cascaded. In this case, the SOUT pin of one device should be connected to the SIN pin of the www.maximintegrated.com next device, effectively cascading the internal shift registers. The CLK and CS pins of all the devices should be connected together in this configuration. See the SerialPort Operation section for more detailed information on operating the SPI interface. Temperature Monitoring The internal junction temperature of the device is constantly monitored. An alarm is raised, by asserting the FAULT pin, if the temperature rises above TALRM. In addition to asserting FAULT, the device sets the OT bit to a 1. Supply Voltage Monitoring A supply voltage monitor circuit constantly monitors the field-supply voltage. If this voltage falls below a threshold (VOFFUVLO), an alarm is raised by asserting the FAULT pin, indicating that the part is experiencing a fault condition and the data in the serializer is not to be trusted. In addition, the device sets the UV bit to a 1. Once the field-supply voltage has recovered and goes above VONUVLO, the FAULT pin is released, indicating normal operation of the part. Maxim Integrated 11 MAX31910 Ultra-Low Power Industrial, Octal, Digital Input Translator/Serializer Applications Information Daisy-Chain Operation EMC Standards Compliance The external components shown in Figure 3 allow the device to operate in harsh industrial environments. Components were chosen to assist in suppression of voltage burst and surge transients, allowing the system to meet or exceed international EMC requirements. Table 2 lists an example device for each component in Figure 3. The system shown in Figure 3, using the components shown in Table 2, is designed to be robust against IEC Fast Transient Burst, surge, conducted RFI specifications, and ESD specifications (IEC 61000-4-2, -4, -5, and -6). Serial-Port Operation Serial output of the device functions in one of two modes, depending on the MODESEL setting (Table 3). With MODESEL = 0, the device output includes a 5-bit CRC, an undervoltage alarm, and an overtemperature alarm. See the Detailed Description for CRC, undervoltage, and overtemperature functional descriptions. With MODESEL = 1, the device outputs only the state of the IN1-IN8 inputs and omits the CRC, undervoltage alarm, and overtemperature alarm. For systems with more than eight sensor inputs, multiple devices can be daisy-chained to allow access to all data inputs through a single serial port. When using a daisychain configuration, connect SOUT of one of the devices to the SIN input of another upstream device. CS and SCK of all devices in the chain should be connected together in parallel (see Figure 4). In a daisy-chain configuration, external components used to enhance EMC robustness do not need to be duplicated for each device of a circuit board. Figure 5 illustrates a 16-input application. SPI Waveforms The serial output of the device adheres to the SPI protocol, running with CPHA = 0 and CPOL = 0. Input states on IN1-IN8 are latched in on the falling edge of CS. The transfer of data out of the slave output, SOUT, starts immediately when CS is asserted (i.e., MSB is output onto SOUT independent of CLK). The remaining data bits are shifted out on the falling edge of CLK. The data bits are written to the output SOUT with MSB first. When CS is high, SOUT is high impedance. The resultant timing is shown in Figure 6. Note that all bits after IN1 are invalid if 8-bit operation mode is selected with the MODESEL input. Figure 7, Figure 8, Figure 9, and Figure 10 illustrate SPI timing specifications. Table 2. Recommended Circuit Components COMPONENT DESCRIPTION REQUIRED/RECOMMENDED/OPTIONAL C0 4.7nF, 2kV polypropylene capacitor Recommended C1 10FF, 60V ceramic capacitor Required C3 100nF, 10V ceramic capacitor Recommended C4 4.7F, 10V low ESR ceramic capacitor C5 100nF, 100V ceramic capacitor Recommended D0 36V fast zener diode (ZSMB36) Recommended D1 General-purpose rectifier (IN4007) Required Optional: For reverse-polarity protection. R1 150I, 1/3W MELF resistor Recommended RINX 2.2kI, 1/4W MELF resistor Required RREF 15kI, 1/8W resistor Required Note: For higher EFT performance, a minimum 1nF, 1000V capacitor can be added from nodes fIN1-fIN8 to earth or ground. For additional methods to improve EFT robustness, please check the Maxim website regularly for upcoming application notes currently being developed. www.maximintegrated.com Maxim Integrated 12 MAX31910 24V Ultra-Low Power Industrial, Octal, Digital Input Translator/Serializer JUMPERS TO 5VOUT AND GND D1 R1 5VOUT VCC24V C0 D0 C1 C5 DB0 C3 DB1 EARTH C4 VDD_LOGIC MODESEL SIN RINX fIN1-8 MAX31910 CLK IN1-8 CLK CS CS ISOLATION SOUT SOUT FAULT FAULT RT1-8 GND RIREF RREF FIELD GROUND 0V C0 EARTH Figure 3. Typical EMC Protection Circuitry SIN SIN MAX31910 SOUT SIN MAX31910 MAX31910 SOUT SOUT TO CONTROLLER Figure 4. Daisy-Chain Operation Table 3. MODESEL Settings MODESEL SETTING FUNCTIONALITY 0 16-bit output; [IN8-IN1][CRC (5 bit)][UV][OT][1] 1 8-bit output; [IN8-IN1] www.maximintegrated.com Maxim Integrated 13 MAX31910 24V Ultra-Low Power Industrial, Octal, Digital Input Translator/Serializer JUMPERS TO 5VOUT AND GND R1 5VOUT VCC24V C0 D0 C1 DB0 DB1 C3 C4 MODESEL EARTH VDD_LOGIC MAX31910 SIN RINX fIN1-8 CLK CLK IN1-8 CS CS ISOLATION RT1-8 RIREF SOUT SOUT FAULT FAULT GND RREF D1 0V C0 EARTH CLK VCC24V CS C1 SOUT FAULT SIN RINX fIN1-8 MAX31910 IN1-8 JUMPERS TO 5VOUT AND GND 5VOUT DB0 DB1 RT1-8 MODESEL RIREF GND C3 C4 RREF Figure 5. 16-Input Application Circuit www.maximintegrated.com Maxim Integrated 14 MAX31910 Ultra-Low Power Industrial, Octal, Digital Input Translator/Serializer CLK SOUT IN8 IN7 IN6 IN5 IN4 IN3 IN2 IN1 CRC4 CRC3 CRC2 CRC1 CRC0 UV OT 1 CS IN8 -IN1 VALID Figure 6. SPI Communication Example tCSPW tP2 tSU1 CS tH1 CLK SIN VALID SIN SOUT Figure 7. SPI Timing Diagram 1 Figure 9. SPI Timing Diagram 3 1/fCLK tSU2 tCSPW tREC CS CS tR/F CLK SOUT tP1 Figure 8. SPI Timing Diagram 2 www.maximintegrated.com tR/F Figure 10. SPI Timing Diagram 4 Maxim Integrated 15 MAX31910 Ultra-Low Power Industrial, Octal, Digital Input Translator/Serializer Chip Information Package Information For the latest package outline information and land patterns (footprints), go to www.maximintegrated.com/packages. Note that a "+", "#", or "-" in the package code indicates RoHS status only. Package drawings may show a different suffix character, but the drawing pertains to the package regardless of RoHS status. PROCESS: S45JRS Ordering Information PART TEMP RANGE PINPACKAGE CARRIER MAX31910AUI+ -40NC to +125NC 28 TSSOP Bulk MAX31910AUI+T -40NC to +125NC 28 TSSOP Tape and Reel PACKAGE TYPE PACKAGE CODE OUTLINE NO. LAND PATTERN NO. 28 TSSOP-EP U28E+4 21-0108 90-0146 +Denotes a lead(Pb)-free/RoHS-compliant package. T = Tape and reel. www.maximintegrated.com Maxim Integrated 16 MAX31910 Ultra-Low Power Industrial, Octal, Digital Input Translator/Serializer Revision History REVISION NUMBER REVISION DATE PAGES CHANGED 0 8/12 Initial release 1 9/12 Changed the supply voltage minimum from 10V to 7V; changed the current limits in the EC table Note 5; added a new Figure 1 to show current-limit switching; added the CRC polynomial to the Reading Serial Data section 1-4, 9 2 11/13 Updated Block Diagram, TOCs 4, 5, 8-10, Input Current Clamp, Low-Power Current Clamp Switching, Basic Application Circuit, and EMC Standards Compliance sections, Table 2, and Figures 2, 4, and 5 1, 5, 6, 8, 10-13 3 7/14 Added Note 11 to DC Electrical Characteristics table, deleted portion of Table 2 note. 4 2/15 Updated front page content 5 4/15 Correct errata in General Description, added powering from 5VOUT, corrected errata in figures, errata in Electrical Characteristics table. DESCRIPTION -- 3, 4, 11 1 1, 3, 5, 8, 10, 12-13, 15 For pricing, delivery, and ordering information, please contact Maxim Direct at 1-888-629-4642, or visit Maxim Integrated's website at www.maximintegrated.com. Maxim Integrated cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim Integrated product. No circuit patent licenses are implied. Maxim Integrated reserves the right to change the circuitry and specifications without notice at any time. The parametric values (min and max limits) shown in the Electrical Characteristics table are guaranteed. Other parametric values quoted in this data sheet are provided for guidance. Maxim Integrated and the Maxim Integrated logo are trademarks of Maxim Integrated Products, Inc. (c) 2015 Maxim Integrated Products, Inc. 17 Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Maxim Integrated: MAX31910AUI+ MAX31910AUI+T