©2018 Littelfuse, Inc.
Specifications are subject to change without notice.
TVS Diode Arrays (SPA ® Diodes)
Revision: 09/03/18
Low Capacitance ESD Protection - SP3014 Series
SP3014-02UTG
Description
Applications
The SP3423 integrates 2 channels of low capacitance
steering diodes and and an avalanche breakdown diode
to provide protection for electronic equipment that may
experience destructive electrostatic discharges (ESD). The
SP3423 can safely absorb repetitive ESD strikes above
the maximum contact level specified in IEC 61000-4-2
international standard (±8kV contact discharge) without
performance degradation.
The low off-state capacitance makes it ideal for protecting
high-speed signal lines such as USB2.0/3.0 and 10GbE
interfaces with an extremely low dynamic resistance to
protect the most sensitive, state of the art chipsets against
ESD transients.
Its flow-through capability makes this SP3423 TVS a PCB
layout friendly component and helps reduce stray PCB
capacitances.
Features
ESD, IEC 61000-4-2,
±10kV contact, ±15kV air
EFT, IEC 61000-4-4, 80A
(tP=5/50ns)
Lightning, 2A (8/20 as
defined in IEC 61000-4-5
2nd edition)
Low capacitance of 0.2pF
(TYP) per I/O
Low leakage current of
0.01μA (TYP) at 5V
Small µDFN-6 footprint
(1.2 mm x 1.0 mm x 0.5
mm)
AEC-Q101 qualified
Moisture Sensitivity
Level(MSL -1)
Halogen free, lead free
and RoHS compliant
LCD/PDP TVs
External Storages
DVD/Blu-ray Players
Set Top Boxes
Smartphones
Ultrabooks/Notebooks
Digital Cameras
Portable Medical
Automotive Electronics
Wearable Technology
USB 2.0/3.0
Ethernet up to 10GbE
Pinout
Functional Block Diagram
Life Support Note:
Not Intended for Use in Life Support or Life Saving Applications
The products shown herein are not designed for use in life sustaining or life saving
applications unless otherwise expressly indicated.
SP3423, 0.2pF, +20kV/-10kV Diode Array RoHS
Pb
GREEN
USB 2.0/3.0 Protection Application Example
GND
USB Port
V
BUS
D+
D-
IC
USB Controller
*Package is shown as transparent
SP3014
SP1003
SP3423
SP3423
μDFN-6 (1.2x1.0x0.5mm)
TOP VIEW
TOP VIEW
©2018 Littelfuse, Inc.
Specifications are subject to change without notice.
TVS Diode Arrays (SPA ® Diodes)
Revision: 09/03/18
Low Capacitance ESD Protection - SP3014 Series
SP3014-02UTG
SP3012
CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the component. This is a stress only rating and operation
of the component at these or any other conditions above those indicated in the operational sections of this specification is not implied.
Absolute Maximum Ratings
Symbol Parameter Value Units
IPP Peak Current (tp=8/20μs) 2 A
TOP Operating Temperature -40 to 125 °C
TSTOR Storage Temperature -55 to 150 °C
Electrical Characteristics (TOP=25ºC)
Parameter Symbol Test Conditions Min Typ Max Units
Reverse Standoff Voltage VRWM IR = 1μA 5.0 V
Breakdown Voltage VBR IR = 1mA 7 8.4 V
Reverse Leakage Current ILEAK VR=5V, Any I/O to GND 0.01 0.5 µA
Clamp Voltage1VC
IPP=1A, tp=8/20µs, Fwd 10.4 13 V
IPP=2A, tp=8/20µs, Fwd 12.3 15 V
Dynamic Resistance2RDYN TLP, tp=100ns, I/O to GND 0.65 Ω
ESD Withstand Voltage1VESD
IEC 61000-4-2 (Contact) ±10 kV
IEC 61000-4-2 (Air) ±15 kV
Diode Capacitance CI/O-GND Reverse Bias=0V, f=3 GHz 0.2 pF
CI/O-I/O 0.1
Note: 1 Parameter is guaranteed by design and/or component characterization.
2. Transmission Line Pulse (TLP) with 100ns width, 2ns rise time, and average window t1=70ns to t2= 90ns
Clamping voltage vs. IPP for 8/20μS waveshape
SP3423
8/20μs Pulse Waveform
0%
10%
20%
30%
40%
50%
60%
70%
80%
90%
100%
110%
0.05.0 10.015.020.025.030.0
Time (μs)
Percent of I
PP
0
2
4
6
8
10
12
14
11.2 1.41.6 1.82
Clamp Voltage (VC
)
Peak Pulse Current
-I
PP (A)
©2018 Littelfuse, Inc.
Specifications are subject to change without notice.
TVS Diode Arrays (SPA ® Diodes)
Revision: 09/03/18
Low Capacitance ESD Protection - SP3014 Series
SP3014-02UTG
Positive Transmission Line Pulsing (TLP) Plot Negative Transmission Line Pulsing (TLP) Plot
IEC 61000-4-2 -8 kV Contact ESD Clamping Voltage
IEC 61000-4-2 +8 kV Contact ESD Clamping Voltage
0
5
10
15
20
25
30
35
40
0510 15 20 25 30 35
TLP Voltage (V)
TLP Current (A)
-20
-15
-10
-5
0
-14-12 -10-8-6-4-20
TLP Voltage (V)
TLP Current (A)
SP3423
©2018 Littelfuse, Inc.
Specifications are subject to change without notice.
TVS Diode Arrays (SPA ® Diodes)
Revision: 09/03/18
Low Capacitance ESD Protection - SP3014 Series
SP3014-02UTG
Time
Temperature
TP
TL
TS(max)
TS(min)
25
tP
tL
tS
time to peak temperature
Preheat
P
rehea
t
Ramp-up
R
amp-up
Ramp-down
R
amp-d
o
Critical Zone
TL to TP
C
ritical Zon
e
T
to
T
P
Reflow Condition Pb – Free assembly
Pre Heat
- Temperature Min (Ts(min)) 150°C
- Temperature Max (Ts(max)) 200°C
- Time (min to max) (ts) 60 – 180 secs
Average ramp up rate (Liquidus) Temp (TL)
to peak 3°C/second max
TS(max) to TL - Ramp-up Rate 3°C/second max
Reflow - Temperature (TL) (Liquidus) 217°C
- Temperature (tL) 60 – 150 seconds
Peak Temperature (TP) 260+0/-5 °C
Time within 5°C of actual peak
Temperature (tp)20 – 40 seconds
Ramp-down Rate 6°C/second max
Time 25°C to peak Temperature (TP) 8 minutes Max.
Do not exceed 260°C
Soldering Parameters
Part Numbering System Part Marking System
SP 3423 xx T G
Series
Package
T= Tape & Reel
G= Green
Number of
Channels
TVS Diode Arrays
(SPA
®
Diodes)
02 = 2 channel
x
µDFN-6LU=
TKD
T : Part code
K : Assembly code
D : Date code
12
3
4
5
6
Part Number Package Min. Order Qty.
SP3423-02UTG µDFN-6L 3000
Ordering Information
SP3423
Product Characteristics
Lead Plating Pre-Plated Frame (µDFN)
Lead Material Copper Alloy
Substrate Material Silicon
Body Material Molded Compound
Flammability UL Recognized compound meeting
flammability rating V-0
©2018 Littelfuse, Inc.
Specifications are subject to change without notice.
TVS Diode Arrays (SPA ® Diodes)
Revision: 09/03/18
Low Capacitance ESD Protection - SP3014 Series
SP3014-02UTG
Package Dimensions —µDFN-6L
1
Top View Bottom View
Side View
D
1
E
3
46
b
L2
L1
e
A
A3
A1
h
0.25mm x6
0.40mm
0.55mm
0.45mm
0.45mm
1.15mm
1.05mm
Recommended Soldering Pad Layout
0.40mm
13
4
6
Drawing# : U02-A
Embossed Carrier Tape & Reel Specification — µDFN-6L
Symbol Millimeters Inches
Min Max Min Max
E1.65 1.85 0.064 0.073
F3.45 3.55 0.135 0.139
P2 1.95 2.05 0.076 0.081
D1.40 1.60 0.055 0.063
D1 0.45 0.55 0.017 0.021
P3.90 4.10 0.154 0.161
10P0 40.0+/-0.20 1.574+/-0.008
W7.90 8.30 0.311 0.319
P0 3.90 4.10 0.154 0.161
A0 1.15 1.25 0.045 0.049
B0 1.75 1.85 0.069 0.073
K0 0.65 0.75 0.026 0.03
t0.22 max 0.009 max
User Feeding Direction
Pin 1 Location
SP3423
,Ref.
,Ref.
,Ref.
8mm TAPE AND REEL
Disclaimer Noce - Informaon furnished is believed to be accurate and reliable. However, users should independently evaluate the suitability of and
test each product selected for their own applicaons. Lielfuse products are not designed for, and may not be used in, all applicaons.
Read complete Disclaimer Noce at hp://www.lielfuse.com/disclaimer-electronics.
µDFN6 (1.2x1.0x0.45mm)
JEDEC MO-229
Symbol Millimeters Inches
Min Nom Max Min Nom Max
A0.40 0.45 0.50 0.016 0.018 0.020
A1 0.00 0.02 0.05 0.000 0.001 0.002
A3 0.125 REF 0.005 REF
b0.15 0.20 0.25 0.006 0.008 0.010
D1.10 1.20 1.30 0.043 0.047 0.051
E0.90 1. 0 0 1. 10 0.035 0.039 0.043
e0.40 REF 0.016 BSC
L1 0.35 0.45 0.55 0.014 0.018 0.022
L2 0.25 0.35 0.45 0.010 0.014 0.018
h0.10 REF 0.004 REF