05096 PSRDA3.3-4 - PSRDA15-4 Only One Name Means ProTek'TionTM 500 WATT LOW CAPACITANCE STEERING DIODE/TVS ARRAY Description The PSRDAxx-4 Series are low capacitance multi-line steering diode/transient voltage suppressor arrays that provides board level protection for standard TTL and CMOS bus line applications against the damaging effects of ESD, tertiary lightning and switching transients. The PSRDAxx-4 Series has a peak pulse power rating of 500 Watts for an 8/20s waveshape. This device series meets the IEC 61000-4-2, IEC 61000-4-4 and IEC 61000-4-5 requirements. SO-8 package Features applications * Compatible with IEC 61000-4-2 (ESD): Air - 15kV, Contact - 8kV * Compatible with IEC 61000-4-4 (EFT): 40A - 5/50ns * Compatible with IEC 61000-4-5 (Surge): 24A, 8/20s - Level 2(LineGnd) & Level 3(Line-Line) * 500 Watts Peak Pulse Power per Line (tp = 8/20s) * Unidirectional Configuration * Available in 3.3V, 5V, 12V & 15V * Protects Up to Four I/O Ports * Low Capacitance: 5pF per Diode * RoHS Compliant * REACH Compliant * * * * Computer Interface Protection Ethernet - 10/100/1000 Base T Set-Top Box Protection Video Card Mechanical characteristics * Molded JEDEC SO-8 Package * Approximate Weight: 70 milligrams * Lead-Free Pure-Tin Plating (Annealed) * Solder Reflow Temperature: Pure-Tin - Sn, 100: 260-270C * 12mm Tape and Reel Per EIA Standard 481 * Flammability Rating UL 94V-0 PIN CONFIGURATION 05096.R11 10/12 GND 8 I/O 4 7 I/O 3 6 GND 5 1 I/O 1 2 +VREF 3 +VREF 4 I/O 2 Page 1 www.protekdevices.com 05096 PSRDA3.3-4 - PSRDA15-4 Only One Name Means ProTek'TionTM typical device characteristics MAXIMUM RATINGS @ 25C Unless Otherwise Specified PARAMETER Peak Pulse Power (tp = 8/20s) - See Figure 1 Operating Temperature SYMBOL VALUE UNITS PPP 500 Watts TL -55 to 150 C Storage Temperature TSTG -55 to 150 C Continuous Power Dissipation PPC 1000 mW Maximum Forward Voltage @ 10mA (Note 1) VF 1.1 Volts Notes 1. Measured between pins 8 or 5 to 1, 2, 3, 4, 6 and 7. ELECTRICAL CHARACTERISTICS PER LINE @ 25C Unless Otherwise Specified PART NUMBER DEVICE MARKING RATED STAND-OFF VOLTAGE minimum breakdown voltage MAXIMUM CLAMPING VOLTAGE (Fig. 2) MAXIMUM LEAKAGE CURRENT MAXIMUM CAPACITANCE (Note 1) (Fig. 6) VWM VOLTS @1mA V(BR) VOLTS @I P = 1A VC VOLTS @VWM ID A @0V, 1MHz C j(SD) pF PSRDA3.3-4 PRA 3.3 4.0 6.5 125 5 PSRDA05-4 PRB 5.0 6.0 9.8 20 5 PSRDA12-4 PRD 12.0 13.3 19.0 1 5 PSRDA15-4 PRE 15.0 16.7 24.0 1 5 Notes 1. Capacitance measured at VWM = VCC connected between I/O pins to pin 8 and 5 (Gnd). VR = VWM @ 1MHz. As shown in Figure 6, REF1 is connected to ground, REF2 is connected to +VCC, and input applies to VCC = 5V, VSIGN = 30mV, F = 1MHz figure 1 peak pulse power vs pulse time PPP - Peak Pulse Power - Watts 10,000 1,000 100 10 0.1 05096.R11 10/12 500W, 8/20s Waveform 1 10 100 td - Pulse Duration - s Page 2 1,000 10,000 www.protekdevices.com 05096 PSRDA3.3-4 - PSRDA15-4 Only One Name Means ProTek'TionTM typical device characteristics figure 2 pulse wave form tf 100 Peak Value IPP 80 100 TEST WAVEFORM PARAMETERS tf = 8s td = 20s e-t 60 40 td = t/(IPP/2) 60 40 20 20 0 Peak Pulse Power 8/20s 80 % Of Rated Power IPP - Peak Pulse Current - % of IPP 120 figure 3 power derating curve 0 5 10 15 t - Time - s 20 25 0 30 Average Power 0 25 50 75 100 125 TA - Ambient Temperature - C 150 figure 4 overshoot & clamping voltage for PSRDA05-4 40 5 Volts per Division 30 20 10 0 ESD Test Pulse - 8 kilovolt, 1/30ns (Waveshape) 05096.R11 10/12 Page 3 www.protekdevices.com 05096 PSRDA3.3-4 - PSRDA15-4 Only One Name Means ProTek'TionTM typical device characteristics figure 5 typcial clamping voltage vs peak pulse current for PSRDA05-4 VC - Clamping Voltage - Volts 12 8 4 0 0 5 10 15 20 IPP - Peak Pulse Current - Amps 25 30 figure 6 input capacitance circuit REF2 I/O +VCC VSIGN G REF1 figure 8 return loss - pSRDA12-4 50 50 20 20 10 db per Division 10 db per Division figure 7 insertion loss - PSRDA12-4 0 -20 -50 -20 -50 100 MHz per Division 05096.R11 10/12 0 100 MHz per Division Page 4 www.protekdevices.com 05096 PSRDA3.3-4 - PSRDA15-4 Only One Name Means ProTek'TionTM SPICE MODEL figure 1 spice model VCC LCRD I/O ABD LCRD Lg 0.8nH ABD - Avalanche Breakdown Diode (TVS) LCRD: Low Capacitance Rectifier Diode Lg - Lead Inductance table 1 - spice parameters parameter unit abd(tvs) LCRD BV V See Table 2 200 IBV A 1 0.01 Cjo pF See Table 2 5 PART NUMBER 05096.R11 10/12 IS A See Table 2 1E-13 Vj V 0.6 0.6 M - 0.33 0.33 N - 1 1 RS Ohms See Table 2 0.31 TT s 1E-8 1E-9 EG eV 1.11 1.11 table 2 - abd specific spice parameters i s (amps) bv(volts) cjo(pF) rs(ohms) PSRDA3.3-4 4.0 438 1E-11 0.21 PSRDA05-4 6.0 284 1E-11 0.14 PSRDA12-4 13.3 123 1E-11 0.4 PSRDA15-4 16.7 102 1E-11 0.52 Page 5 www.protekdevices.com 05096 PSRDA3.3-4 - PSRDA15-4 Only One Name Means ProTek'TionTM application information USB Port V BUS D+ D- VBUS GND 3 2 1 5 6 7 8 USB Controller 4 GND GND USB Port V BUS D+ DGND figure 1 - differential mode usb protection Circuit connectivity is as follows: * Pins 1, 2, 4, 6 and 7 connected to the datalines. * Pin 5 and 8 connected to ground. * Pins 2 and 3 connected to the databus. circuit board recommendations Circuit board layout is critical for electromagnetic compatibility protection. The following guidelines are recommended: * The protection device should be placed near the input terminals or connectors, the device will divert the transient current immediately before it can be coupled into the nearby traces. * The path length between the TVS device and the protected line should be minimized. * All conductive loops including power and ground loops should be minimized. * The transient current return path to ground should be kept as short as possible to reduce parasitic inductance. * Ground planes should be used whenever possible. For multilayer PCBs, use ground vias. 05096.R11 10/12 Page 6 www.protekdevices.com 05096 PSRDA3.3-4 - PSRDA15-4 Only One Name Means ProTek'TionTM SO-8 package information outline dimensions dim millimeters -A- inches min max min max A 4.80 5.00 0.189 0.196 B 3.80 4.00 0.150 0.157 C 1.35 1.75 0.054 0.068 D 0.35 0.49 0.014 0.019 F 0.40 1.25 0.016 0.049 G 1.27 BSC 8 5 -B- 1 G 4 D 0.18 0.25 0.007 0.009 K 0.10 0.25 0.004 0.008 P 5.80 6.20 0.229 0.244 R 0.25 0.50 0.010 0.019 R x 45 C 0.05 BSC J + 0.010" (0.25mm) M B M 4 PL P 0 - 10 -T- K + 0.010" (0.25mm) M T B S A S 8 PL J F NOTES 1. 2. 3. 4. 5. 6. -T- = Seating plane and datum surface. Dimensions "A" and "B" are datum. Dimensions "A" and "B" do not include mold protrusion. Maximum mold protrusion is 0.015" (0.380mm) per side. Dimensioning and tolerances per ANSI Y14.5M, 1982. Dimensions are exclusive of mold flash and metal burrs. A pad layout dimensions dim millimeters B inches min max min max A 1.14 1.40 0.045 0.055 B 0.64 0.89 0.025 0.035 C 6.22 - 0.245 - D 3.94 4.17 0.155 0.165 E 1.02 1.27 0.040 0.050 NOTES 1. Controlling dimension: inches. 05096.R11 10/12 D C E Page 7 www.protekdevices.com 05096 PSRDA3.3-4 - PSRDA15-4 Only One Name Means ProTek'TionTM TAPE AND REEL P0 D t 10 Pitches Cumulative Tolerance on tape 0.2 P2 E F W K0 B0 A0 P User Direction of Feed specifications Reel Dia. Tape Width 178mm (7") 12mm A0 B0 K0 D E F W P0 P2 P tmax 6.50 0.10 5.40 0.10 2.00 0.10 1.50 0.10 1.75 0.10 5.50 0.05 12.00 0.30 4.00 0.12 2.00 0.10 4.00 0.10 0.25 Notes 1. 2. 3. 4. 5. 6. Dimensions are in millimeters. Surface mount product is taped and reeled in accordance with EIA-481. Suffix - T7 = 7" Reel - 1,000 pieces per 12mm tape. Suffix - T13 = 13" Reel - 2,500 pieces per 12mm tape. Bulk product shipped in tubes of 98 pieces per tube. Marking on Part - marking code (see page 2), date code, logo and pin one defined by dot on top of package. Package outline, pad layout and tape specifications per document number 06009.R3 9/10. ORDERING INFORMATION base PART NUMBER (xx = Voltage) LEADFREE SUFFIX TAPE SUFFIX QTY/REEL REEL SIZE TUBE qty PSRDAxx-4 -LF -T7 1,000 7" 98 PSRDAxx-4 -LF -T13 2,500 13" 98 This device is only available in a Lead-Free configuration. 05096.R11 10/12 Page 8 www.protekdevices.com 05096 PSRDA3.3-4 - PSRDA15-4 Only One Name Means ProTek'TionTM company information COMPANY PROFILE In business more than 20 years, ProTek DevicesTM is a privately-held company located in Tempe, Arizona, that offers a product line of transient voltage suppressors (TVS); avalanche breakdown diodes; steering diode TVS arrays and other surge suppressor component products. These TVS devices protect electronic systems from the effects of lightning, electrostatic discharge (ESD), nuclear electromagnetic pulses (NEMP), inductive switching and EMI / RFI. ProTek Devices also offers high performance interface and linear products that include analog switches; multiplexers; LED drivers; audio control ICs; RF and related high frequency products. The analog devices work in a host of consumer; industrial; automotive and other applications. CONTACT US Corporate Headquarters 2929 South Fair Lane Tempe, Arizona 85282 USA By Telephone General: 602-431-8101 Sales: & Marketing: 602-414-5109 Customer Service: 602-414-5114 Product Technical Support: 602-414-5107 By Fax General: 602-431-2288 By E-mail: Sales: sales@protekdevices.com Customer Service: service@protekdevices.com Technical Support: support@protekdevices.com ProTek Devices (Asia Pacific) Pte. Ltd. 8 Ubi Road 2, #06-19 Zervex Singapore - 408538 Tel: +65-67488312 Fax: +65-67488313 Web www.protekdevices.com COPYRIGHT (c) ProTek Devices 2007 - This literature is subject to all applicable copyright laws and is not for resale in any manner. SPECIFICATIONS: ProTek reserves the right to change the electrical and or mechanical characteristics described herein without notice. DESIGN CHANGES: ProTek reserves the right to discontinue product lines without notice and that the final judgement concerning selection and specifications is the buyer's and that in furnishing engineering and technical assistance. ProTek assumes no responsibility with respect to the selection or specifications of such products. ProTek makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does ProTek assume any liability arising out of the application or use of any product or circuit and specifically disclaims any and all liability without limitation special, consequential or incidental damages. LIFE SUPPORT POLICY: ProTek Devices products are not authorized for use in life support systems without written consent from the factory. 05096.R11 10/12 Page 9 www.protekdevices.com