LT8495 SEPIC/Boost Converter with 2A, 70V Switch, 9A Quiescent Current, POR and Watchdog Timer DESCRIPTION FEATURES n n n n n n n n n n n Wide Input Voltage Range of ~1V to 60V (2.5V to 32V for Start-Up) Low Ripple Burst Mode(R) Operation n 9A I at 12V to 5.0V Q IN OUT n Output Ripple (<10mV Typ.) Dual Supply Pins: n Improves Efficiency n Reduces Minimum Supply Voltage to ~1V after Start-Up to Extend Battery Life Integrated 2A/70V Power Switch Programmable Watchdog Timer Can Operate When VIN Supply Is Removed Programmable Power-On Reset Timer (POR) with RST Functional for Input Supply Down to 1.3V FMEA Fault Tolerant in TSSOP Package Fixed Frequency PWM, SEPIC/BOOST/FLYBACK Topologies Programmable Switching Frequency: 250kHz to 1.5MHz UVLO Programmable on SWEN and RSTIN Pins Soft-Start Programmable with One Capacitor Small 20-Lead QFN or 20-Lead TSSOP Packages The LT(R)8495 is an adjustable frequency (250kHz to 1.5MHz) monolithic switching regulator with a power-on reset and watchdog timer. Quiescent current can be less than 9A when operating and is ~0.3A when SWEN, WDE and RSTIN are low. Configurable as a SEPIC, boost or flyback converter, the low ripple Burst Mode operation maintains high efficiency at low output current while keeping output ripple below 10mV. Dual supply pins (VIN and BIAS) allow the part to automatically operate from the most efficient supply. Input supply voltage can be up to 60V for SEPIC topologies and up to 32V (with ride-through up to 60V) for boost and flyback topologies. After start-up, battery life is extended since the part can draw current from its output (BIAS) even when VIN voltage drops below 2.5V. The reset and watchdog timeout periods are independently adjustable using external capacitors. Using a resistor divider on the SWEN pin provides a programmable undervoltage lockout (UVLO) for the converter. A resistor divider connected to RSTIN provides UVLO control that asserts the RST pin. Additional features such as frequency foldback and softstart are integrated. Fault tolerance in the TSSOP allows for adjacent pin shorts or an open without raising the output voltage above its programmed value. The LT8495 is available in 20-lead QFN and 20-lead TSSOP packages with exposed pads for low thermal resistance. APPLICATIONS n n n Automotive ECU Power Power for Portable Products Industrial Supplies L, LT, LTC, LTM, Linear Technology, the Linear logo and Burst Mode are registered trademarks of Linear Technology Corporation. All other trademarks are the property of their respective owners. TYPICAL APPLICATION No-Load Supply Current 450kHz, 5V Output SEPIC Converter 15H 2.2F 2.2F 15H 1M 4.7pF * SW VIN SWEN 1nF 4.7nF 1F 169k CWDT CPOR SS RT LT8495 BIAS RSTIN FB 8.87k 316k C 8495 TA01a 90 85 20 15 10 WATCHDOG ENABLED 5 GND WDO WDE RST WDI VOUT 5V 47F 0.35A (VIN = 3V) 0.6A (VIN = 5V) x2 1.0A (VIN >12V) SUPPLY CURRENT (A) * VIN 3V TO 60V Efficiency 25 EFFICIENCY (%) n 0 WATCHDOG DISABLED 0 12 24 36 INPUT VOLTAGE (V) 48 60 8495 TA01b VIN = 24V 80 VIN = 12V VIN = 5V 75 70 65 60 0.0 0.2 0.4 0.6 LOAD CURRENT (A) 0.8 1.0 8495 TA01c 8495fa For more information www.linear.com/LT8495 1 LT8495 ABSOLUTE MAXIMUM RATINGS (Note 1) VIN, BIAS Voltage.......................................................60V SWEN, WDE, RSTIN Voltage......................................60V FB Voltage..................................................................60V SW Voltage................................................................70V WDI, RST, WDO Voltage...............................................6V RT Voltage...................................................................6V CPOR, CWDT, SS Voltage............................................3V Operating Junction Temperature Range LT8495E, LT8495I (Notes 2, 3)........... -40C to 125C LT8495H (Notes 2, 3)......................... -40C to 150C Storage Temperature Range................... -65C to 150C Lead Temperature (Soldering, 10 sec) FE Package........................................................ 300C PIN CONFIGURATION BIAS CPOR 1 20 SW FB 2 19 NC 20 19 18 17 16 FB 3 18 VIN NC 4 17 NC CPOR 5 CWDT 6 RST 7 14 GND SS 8 13 WDE NC 9 12 SWEN RT 10 11 RSTIN 15 GND SS 1 RT 2 16 WDI GND 3 15 WDO 14 GND 21 GND GND 4 13 GND 12 SW 11 GND FE PACKAGE 20-LEAD PLASTIC TSSOP JA = 38C/W EXPOSED PAD (PIN 21) IS GND, MUST BE SOLDERED TO PCB 8 WDO 9 10 VIN 7 WDI 6 WDE RSTIN 5 SWEN 21 GND FB BIAS RST CWDT TOP VIEW TOP VIEW UF PACKAGE 20-LEAD (4mm x 4mm) PLASTIC QFN JA = 47C/W EXPOSED PAD (PIN 21) IS GND, MUST BE SOLDERED TO PCB ORDER INFORMATION LEAD FREE FINISH TAPE AND REEL PART MARKING* PACKAGE DESCRIPTION TEMPERATURE RANGE LT8495EUF#PBF LT8495EUF#TRPBF 8495 20-Lead (4mm x 4mm) Plastic QFN -40C to 125C LT8495IUF#PBF LT8495IUF#TRPBF 8495 20-Lead (4mm x 4mm) Plastic QFN -40C to 125C LT8495EFE#PBF LT8495EFE#TRPBF LT8495FE 20-Lead Plastic TSSOP -40C to 125C LT8495IFE#PBF LT8495IFE#TRPBF LT8495FE 20-Lead Plastic TSSOP -40C to 125C LT8495HFE#PBF LT8495HFE#TRPBF LT8495FE 20-Lead Plastic TSSOP -40C to 150C Consult LTC Marketing for parts specified with wider operating temperature ranges. *The temperature grade is identified by a label on the shipping container. For more information on lead free part marking, go to: http://www.linear.com/leadfree/ For more information on tape and reel specifications, go to: http://www.linear.com/tapeandreel/ 8495fa 2 For more information www.linear.com/LT8495 LT8495 ELECTRICAL CHARACTERISTICS The l denotes the specifications which apply over the full operating junction temperature range, otherwise specifications are at TA = 25C. VIN = VSWEN = 12V, VBIAS = VWDE = 5V, unless otherwise noted (Note 2). PARAMETER CONDITIONS Minimum VIN Operating Voltages VBIAS < 2.5V VBIAS 2.5V Minimum BIAS Operating Voltages VIN < 2.5V VIN 2.5V Power Switch Driver (PSD) Overvoltage Threshold VIN or BIAS Rising VIN or BIAS Falling (Note 4) MIN TYP MAX l l 2.4 2.5 0 V V l l 2.4 2.5 0 V V 34 33.9 36.5 36.4 V V l l 32.1 32 Power Switch Driver (PSD) Overvoltage Threshold Hysteresis (Note 4) Quiescent Current from VIN Quiescent Current from BIAS BIAS to VIN Comparator Threshold 100 VSWEN = 0V, VWDE = 0V, VRSTIN = 0V VSWEN = 5V, VWDE = 0V, VFB = VRSTIN = 1.25V VSWEN = 5V, VWDE = 5V, VFB = VRSTIN = 1.25V VSWEN = 5V, VWDE = 0V, VFB = VRSTIN = 1.25V (LT8495E, LT8495I) (LT8495H) VSWEN = 5V, VWDE = 5V, VFB = VRSTIN = 1.25V (LT8495E, LT8495I) (LT8495H) VSWEN = 0V, VWDE = 0V, VRSTIN = 0V VSWEN = 5V, VWDE = 0V, VFB = VRSTIN = 1.25V VSWEN = 5V, VWDE = 5V, VFB = VRSTIN = 1.25V VSWEN = 5V, VWDE = 0V, VFB = VRSTIN = 1.25V (LT8495E, LT8495I) (LT8495H) VSWEN = 5V, VWDE = 5V, VFB = VRSTIN = 1.25V (LT8495E, LT8495I) (LT8495H) VBIAS-VIN, VBIAS Rising, VIN = 12V VBIAS-VIN, VBIAS Falling, VIN = 12V Hysteresis (Rising-Falling Threshold) Feedback Voltage UNITS mV 0.3 3.0 3.1 0.9 4.8 4.9 A A A l l 3.0 3.0 6.2 8.0 A A l l 3.1 3.1 6.3 8.0 A A 0.07 1.7 6.0 0.5 2.8 8.5 A A A l l 1.7 1.7 4.0 11 A A l l 6.0 6.0 10.0 15.5 A A l l l 0.55 0.17 0.20 0.90 0.37 0.53 1.2 0.57 0.80 V V V l 1.178 1.202 1.230 V FB Pin Bias Current (Note 7) VFB = 1.202V 0.1 20 nA FB Voltage Line Regulation 5V VIN 32V, VBIAS = 5V 5V VIN 32V, VBIAS = 0V 0.2 0.2 10 10 m%/V m%/V Minimum Switch Off-Time 70 ns Minimum Switch On-Time 95 ns l l 0.92 219 1.0 250 1.06 280 MHz kHz Switch Current Limit at Min. Duty Cycle (Note 5) l 2.1 2.55 2.95 A Switch Current Limit at Max. Duty Cycle (Note 6) l 1.3 1.85 2.4 A Switching Frequency Switch VCESAT RT = 68.1k RT = 324k ISW = 1.2A Switch Leakage Current (Note 7) VSW = 12V, VSWEN = 0V Soft-Start Charging Current (Note 7) VSS = 100mV SWEN Pin Current (Note 7) VSWEN = 1.2V VSWEN = 5V VSWEN = 12V SWEN Rising Voltage Threshold 340 l l SWEN Voltage Hysteresis 5.2 0.9 mV 0.01 1 A 8.2 12.2 A 0 35 240 25 200 550 nA nA nA 1 1.1 30 V mV 8495fa For more information www.linear.com/LT8495 3 LT8495 ELECTRICAL CHARACTERISTICS The l denotes the specifications which apply over the full operating junction temperature range, otherwise specifications are at TA = 25C. VIN = VSWEN = 12V, VBIAS = VWDE = 5V, unless otherwise noted (Note 2). PARAMETER CONDITIONS RSTIN Pin Current (Note 7) VRSTIN = 1.2V VRSTIN = 5V VRSTIN = 12V MIN RSTIN Threshold as % of VFB Regulation Voltage TYP MAX UNITS 0 35 240 25 200 550 nA nA nA l 86 92 97 % RSTIN Low to RST Asserted (tUV) Step VRSTIN from 1.3V to 0.9V l 8 23 60 s Watchdog Timeout and Reset Delay Period (tRST) (Note 8) CPOR = 4700pF, Watchdog Timeout Not Occurring at Same Time as the Reset Delay l 8.5 9.5 11.85 ms Watchdog Upper Boundary (tWDU) (Note 8) CWDT = 1000pF l 14.9 16.7 20.9 ms Watchdog Lower Boundary (tWDL) (Note 8) CWDT = 1000pF l 580 650 812 s RST Output Voltage Low ISINK = 1.25mA ISINK = 100A, VBIAS = 1.3V, VIN = 0V ISINK = 100A, VIN = 1.3V, VBIAS = 0V l l l 33 15 15 150 150 150 mV mV mV RST Leakage Current VRSTIN = 1.2V, VRST = 5V (LT8495E, LT8495I) VRSTIN = 1.2V, VRST = 5V (LT8495H) l l 0 0 0.3 1.0 A A WDO Output Voltage Low ISINK = 1.25mA l 120 420 mV WDO Leakage Current VWDO = 5V l 0 0.25 A WDI Pin Current VWDI = 5V 0 0.1 A 0.8 1.25 V WDI Input Rising Threshold l 0.4 WDI Voltage Hysteresis 58 WDI Input Pulse Width WDE Pin Current (Note 7) l 300 VWDE = 1.2V VWDE = 5V VWDE = 12V WDE Rising Voltage Threshold l WDE Voltage Hysteresis 0.9 ns 0 35 240 25 200 550 nA nA nA 1 1.1 V 30 Note 1: Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. Exposure to any Absolute Maximum Rating condition for extended periods may affect device reliability and lifetime. Voltages are with respect to GND pin unless otherwise noted. Note 2: The LT8495E is guaranteed to meet performance specifications from 0C to 125C junction temperature. Specifications over the -40C to 125C operating junction temperature range are assured by design, characterization and correlation with statistical process controls. The LT8495I is guaranteed to meet performance specifications from -40C to 125C junction temperature. The LT8495H is guaranteed over the full -40C to 150C operating junction temperature range. Operating lifetime is derated at junction temperatures greater than 125C. Note 3: This IC includes overtemperature protection that is intended to protect the device during momentary overload conditions. Junction temperature will exceed the maximum operating range when mV mV overtemperature protection is active. Continuous operation above the specified maximum operating junction temperature may impair device reliability. Note 4: See Power Supplies and Operating Limits in the Applications Information section for more details. Note 5: Current limit guaranteed by design and/or correlation to static test. Slope Compensation reduces current limit at higher duty cycles. Note 6: Max duty cycle current limit measured at 1MHz switching frequency. Note 7: Polarity specification for all currents into pins is positive. All voltages are referenced to GND unless otherwise specified. Note 8: This specification is guaranteed for only the exact capacitance as listed in the conditions. Variation of the capacitance from the exact listed value will cause proportional variation to tRST, tWDU and tWDL. 8495fa 4 For more information www.linear.com/LT8495 LT8495 TYPICAL PERFORMANCE CHARACTERISTICS No Load Supply Current FRONT PAGE APPLICATION VIN=12V Load Regulation 0.15 FRONT PAGE APPLICATION 0.10 2.0 60 40 20 TYPICAL LOAD REGULATION (%) SUPPLY CURRENT (A) 80 Maximum Load Current 2.5 LOAD CURRENT (A) 100 TA = 25C, unless otherwise noted. 1.5 1.0 MINIMUM 0.5 0 -50 -10 30 70 110 TEMPERATURE (C) 0 12 24 36 VIN (V) 48 8495 G01 60 -0.15 VSW 10V/DIV IL 0.5A/DIV IL 0.5A/DIV VOUT 5mV/DIV VOUT 5mV/DIV 8495 G04 8495 G07 200 400 600 800 LOAD CURRENT (mA) 1000 Transient Load Response; Load Current Is Stepped from 300mA to 500mA IL 0.5A/DIV 8495 G05 500s/DIV FRONT PAGE APPLICATION VIN = 12V VOUT = 5V 3.0 2.5 2.5 SWITCH CURRENT LIMIT (A) 3.0 2.0 1.5 1.0 0.5 0.0 10 20 30 40 50 60 70 DUTY CYCLE (%) 80 8495 G06 Switch Current Limit at Minimum Duty Cycle Switch Current Limit at 500kHz SWITCH CURRENT LIMIT (A) IL 0.5A/DIV 0 VOUT 50mV/DIV 1s/DIV FRONT PAGE APPLICATION VIN = 12V VOUT = 5V ILOAD = 0.5A Transient Load Response; Load Current Is Stepped from 20mA (Burst Mode Operation) to 220mA VOUT 100mV/DIV VIN=12V FRONT PAGE APPLICATION REFERENCED TO VOUT AT 100mA LOAD LT8495 G03 Switching Waveforms, Full Frequency Continuous Operation VSW 10V/DIV 500s/DIV FRONT PAGE APPLICATION VIN = 12V VOUT = 5V -0.05 8495 G02 Switching Waveforms, Burst Mode Operation 10ms/DIV FRONT PAGE APPLICATION VIN = 12V VOUT = 5V ILOAD = 20mA -0.00 -0.10 0.0 150 0.05 90 8495 G08 2.0 1.5 1.0 0.5 0.0 -50 0 50 100 TEMPERATURE (C) 150 8495 G09 8495fa For more information www.linear.com/LT8495 5 LT8495 TYPICAL PERFORMANCE CHARACTERISTICS Switch VCESAT Feedback Voltage 1.25 400 300 200 FREQUENCY (MHz) 1.22 FB VOLTAGE (V) SWITCH VCESAT (mV) 500 1.21 1.20 1.19 100 0 0.0 0.5 1.5 1.0 SWITCH CURRENT (A) 1.18 -50 2.0 Frequency Foldback 0 100 50 TEMPERATURE (C) RT = 324k 200 0.5 0.7 FB VOLTAGE (V) 1.0 100 80 60 40 0 50 100 TEMPERATURE (C) 20 VIN OR BIAS RISING 34.5 VIN OR BIAS FALLING 33.5 100 50 TEMPERATURE (C) 150 8495 G16 UPPER BOUNDARY PERIOD, t WDU (ms) 35.0 0 100 80 60 40 0 -50 150 0 50 100 TEMPERATURE (C) 19 Watchdog Lower Boundary Period 760 CWDT = 1nF TDK C2012C0G1H102J 18 17 16 15 -50 -10 150 8495 G15 Watchdog Upper Boundary Period Overvoltage Lockout 35.5 33.0 -50 120 8495 G14 8495 G13 34.0 140 20 0 -50 1.2 150 160 20 0.2 50 100 TEMPERATURE (C) Minimum Switch Off-Time SWITCH OFF-TIME (ns) 600 0 180 120 SWITCH ON-TIME (ns) SWITCHING FREQUENCY (kHz) 800 RT = 324k 8495 G12 Minimum Switch On-Time RT = 68.1k 0 0.0 0.50 0.00 -50 150 140 400 0.75 8495 G11 1200 1000 RT = 68.1k 1.00 0.25 8495 G10 VIN OR BIAS VOLTAGE (V) Oscillator Frequency 1.50 1.23 LOWER BOUNDRY PERIOD t WDL (s) 600 TA = 25C, unless otherwise noted. 30 70 110 TEMPERATURE (C) 150 8495 G17 CWDT = 1nF TDK 740 C2012COG1H102J 720 700 680 660 640 620 -50 0 50 100 TEMPERATURE (C) 150 8495 G18 8495fa 6 For more information www.linear.com/LT8495 LT8495 TYPICAL PERFORMANCE CHARACTERISTICS Watchdog Upper Boundary Period vs Capacitance Reset Timeout Period 10 9 0 50 100 TEMPERATURE (C) 10k RESET TIMEOUT PERIOD, t RST (ms) 11 8 -50 10k 1k 100 10 1 0.1 0.01 150 0.1 1 10 100 CWDT PIN CAPACITANCE, CWDT (nF) 8495 G19 0.1 1 10 100 CWDT PIN CAPACITANCE, CWDT (nF) 1 0.1 1 10 100 CPOR PIN CAPACITANCE, CPOR (nF) FB Pin Current 1000 350 100 300 250 200 150 100 10 1 0.1 0.01 50 0 1000 1000 8495 G21 FB PIN CURRENT (A) SWEN/RSTIN/WDE PIN CURRENT (nA) 0.1 0 10 30 40 50 20 SWEN/RSTIN/WDE PIN VOLTAGE (V) 0.001 60 0 10 30 40 20 FB VOLTAGE (V) RST Output Voltage vs Supply Voltage 50 60 8495 G24 8495 G23 8495 G22 Internal UVLO 2.50 10k PULL-UP FROM VIN TO RST VIN/BIAS VOLTAGE (V) 3 RST OUTPUT VOLTAGE (V) LOWER BOUNDARY PERIOD, t WDU (ms) 1 10 0.1 0.01 1000 400 10 100 SWEN/RSTIN/WDE Pin Current 1k 100 1k 8495 G20 Watchdog Lower Boundary Period vs Capacitance 0.01 0.01 Reset Timeout Period vs Capacitance 100k CPOR = 4.7nF TDK C2012COG1H472J UPPER BOUNDARY PERIOD, t WDU (ms) RESET TIMEOUT PERIOD t RST (ms) 12 TA = 25C, unless otherwise noted. 2 1 0 0 1 2 VIN/BIAS VOLTAGE (V) 2.45 VIN/BIAS RISING 2.40 VIN/BIAS FALLING 2.35 2.30 -50 3 8495 G25 0 50 100 TEMPERATURE (C) 150 8495 G26 8495fa For more information www.linear.com/LT8495 7 LT8495 TYPICAL PERFORMANCE CHARACTERISTICS RST Pin Current vs Supply Voltage VIN = BIAS = RSTIN, SWEN = WDE = 0 16 14 12 10 8 VIN = BIAS, SWEN = WDE = RSTIN = 0 6 4 CURRENT INTO PIN (nA) RST = 0.4V 18 RST PIN CURRENT (mA) Pin Current 60 Quiescent Current 12 VFB = 1.25V VSWEN = VWDE = VRSTIN = 1.2V 10 QUIESCENT CURRENT (A) 20 TA = 25C, unless otherwise noted. 40 IFB 20 ISWEN = IWDE = IRSTIN VIN = 12V, VBIAS = 5V VSWEN = VWDE = 5V VFB = VRSTIN = 1.25V 8 6 CURRENT INTO BIAS 4 CURRENT INTO VIN 2 2 0 0 1 3 2 VIN VOLTAGE (V) 4 5 8495 G27 0 -50 0 100 50 TEMPERATURE (C) 150 8495 G28 0 -50 0 100 50 TEMPERATURE (C) 150 8495 G29 8495fa 8 For more information www.linear.com/LT8495 LT8495 PIN FUNCTIONS (QFN/TSSOP) SS (Pin 1/Pin 8): Soft-Start Pin. Place a soft-start capacitor on this pin. Upon start-up, the SS pin will be charged by a (nominally) 256k resistor to about 2.1V. RT (Pin 2/Pin 10): Oscillator Frequency Set Pin. Place a resistor from this pin to ground to set the internal oscillator frequency. Minimize capacitance on this pin. See the Applications Information section for more details. GND (Pins 3, 4, 11, 13, 14, 15, Exposed Pad 21/Pin 14, Exposed Pad 21): Ground. Solder all pins and the exposed pad directly to the local ground plane. The exposed pad metal of the package provides both electrical contact to ground and good thermal contact to the printed circuit board. NC (Pins 4, 9, 17, 19, TSSOP only): No Connects: These pins are not connected to internal circuitry and must be left floating to ensure fault tolerance. RSTIN (Pin 5/Pin 11): Reset Input Reference. Connect a resistor divider to RSTIN to set the threshold voltage for asserting RST. The RSTIN voltage is compared to an internal 1.1V reference. RSTIN voltages lower than the reference cause RST to assert low. SWEN (Pin 6/Pin 12): Switch Enable Detect Pin. This pin enables/disables the switching regulator and soft-start. A resistor divider can be connected to SWEN to perform an undervoltage lockout function. WDE (Pin 7/Pin 13): Watchdog Timer Enable Pin. Drive above 1.1V to enable the watchdog timer function. When WDE is low, the WDO output driver is disabled causing the pin to be high impedance. WDO (Pin 8/Pin 15): Watchdog Out. Active low, opendrain output. WDO asserts low if WDE is enabled and the microcontroller fails to drive the WDI pin of the LT8495 with the appropriate signal. WDI (Pin 9/Pin 16): Watchdog Timer Input Pin. This pin receives the watchdog signal from a microcontroller. If the appropriate signal is not received, WDO will pulse low for a period equal to the reset delay timer period (tRST). VIN (Pin 10/Pin 18): Supply Input Pin. This pin is typically connected to the input of the DC/DC converter. Must be locally bypassed. SW (Pin 12/Pin 20): Switch Pin. This is the collector of the internal NPN power switch. Minimize trace area connected to this pin to minimize EMI. BIAS (Pin 16/Pin 1): Supply Input Pin. This pin is typically connected to the output of the DC/DC converter in cases where VIN can be higher than VOUT. Must be locally bypassed. FB (Pin 17/Pins 2, 3): Output Voltage Feedback Pin. The LT8495 regulates the FB pin to 1.202V. Connect a resistor divider between the output, FB and GND to set the regulated output voltage. CPOR (Pin 18/Pin 5): WDO and RST Active Delay Period Programming Pin. Attach an external capacitor (CPOR) to GND to set the period (tRST). See the Applications Information section for more information. CWDT (Pin 19/Pin 6): Watchdog Timer Programming Pin. Place a capacitor (CWDT) between this pin and ground to adjust the watchdog timer upper (tWDU) and lower (tWDL) boundary periods. See the Applications Information section for more information. RST (Pin 20/Pin 7): Active Low, Open-Drain Reset. Asserts low when RSTIN is less than ~1.1V (see Electrical Characteristics). After RSTIN rises, RST will remain asserted low for the period (tRST) set by the capacitor on the CPOR pin. 8495fa For more information www.linear.com/LT8495 9 LT8495 BLOCK DIAGRAM 2.1V SS Q S SR2 R 256k 100mV CHIP SHUTDOWN SOFTSTART FB 1.00V + - DIE TEMP 165C 34V - + + - + - VOLTAGE REFS ILIMIT VC_LIMITER - +A1 FREQUENCY FOLDBACK 2.1V 1.10V 1.00V OTHERS Burst Mode DETECT VC 34V - + + - R Q SR1 S QUADRATIC RAMP GENERATOR RSTIN 1.10V POWER SWITCH DRIVER WDI + - GND RST - + PGOOD RESET WDO ADJUSTABLE RESET PULSE GENERATOR WATCHDOG TIMEOUT ENABLE TRANSITION DETECT 2.4V Q1 + - CHIP SHUTDOWN 1.00V BIAS SW - +A3 ADJUSTABLE OSCILLATOR WDE 2.4V LOW POWER MODE A2 RT VIN SUPPLY SELECT LOGIC DISABLE PSD 1.202V SWEN + - OVP 2.3A 2.3A CPOR WATCHDOG TIMER 23A 23A CWDT 8495 BD 8495fa 10 For more information www.linear.com/LT8495 LT8495 TIMING DIAGRAMS Start-Up Timing RSTIN Timing 2.4V VIN RSTIN 1.1V 1.3V RST SS tRST tUV 8495 TD02 RST WDO 1.202V 0.2V CPOR CWDT 8495 TD01 tSTARTUP tDW tRST Watchdog Timing, Lower Boundary WDI CWDT WDO tWDL t < tWDL tRST 8495 TD02a Watchdog Timing, Upper Boundary WDI CWDT WDO tWDU tRST 8495 TD03 tSTARTUP = TIME REQUIRED TO START UP THE CHIP, APPROXIMATELY 1ms tDW = TIME REQUIRED TO START UP THE WATCHDOG OR POR TIMER, APPROXIMATELY 200s tUV = TIME REQUIRED TO ASSERT RST LOW AFTER RSTIN GOES BELOW ITS THRESHOLD, APPROXIMATELY 23s tRST = PROGRAMMED RESET PERIOD tWDU = WATCHDOG UPPER BOUNDARY PERIOD, APPROXIMATELY 31 RAMPING CYCLES ON CWDT PIN tWDL = WATCHDOG LOWER BOUNDARY PERIOD, APPROXIMATELY 1 RAMPING CYCLE ON CWDT PIN 8495fa For more information www.linear.com/LT8495 11 LT8495 OPERATION The LT8495 is a constant-frequency, current mode SEPIC/boost/flyback regulator with power-on reset and a watchdog timer. Operation can be best understood by referring to the Block Diagram. The switching regulation, watchdog timer and reset detection functions are controlled by the SWEN, WDE and RSTIN pins respectively. If all three pins are grounded, the part enters shutdown with minimal current drawn from the VIN and BIAS sources. If any of these three pins are driven above their respective thresholds, this part is turned on. Switching Regulator Operation In the Block Diagram, the adjustable oscillator, with frequency set by the external RT resistor, enables an RS latch, turning on the internal power switch. An amplifier and comparator monitor the switch current flowing through an internal sense resistor, turning the switch off when this current reaches a level determined by the voltage at VC. An error amplifier adjusts the VC voltage by measuring the output voltage through an external resistor divider tied to the FB pin. If the error amplifier's output voltage (VC) increases, more current is delivered to the output; if the VC voltage decreases, less current is delivered. An active clamp on the VC voltage provides current limit. An internal regulator provides power to the control circuitry. In order to improve efficiency, the NPN power switch driver (see Block Diagram) supplies NPN base current from whichever of VIN and BIAS has the lower supply voltage. However, if either of them is below 2.4V or above 34V (typical values), the power switch draws current from the other pin. If both supply pins are below 2.4V or above 34V then switching activity is stopped. To further optimize efficiency, the LT8495 automatically enters Burst Mode operation in light load situations. Between bursts, all circuitry associated with controlling the output switch is shut down, reducing the VIN/BIAS pin supply currents to be less than 3A to 6A typically (see Electrical Characteristics table). Start-Up Operation Several functions are provided to enable a very clean start-up for the LT8495. * First, the SWEN pin voltage is monitored by an internal voltage reference to give a precise turn-on threshold. An external resistor divider can be connected from the input power supply to the SWEN pin to provide a userprogrammable undervoltage lock-out function. * Second, the soft-start circuitry provides for a gradual ramp-up of the switch current. When the part is brought out of shutdown, the external SS capacitor is first discharged, and then an integrated 256k resistor pulls the SS pin up to ~2.1V. By connecting an external capacitor to the SS pin, the voltage ramp rate on the pin can be set. Typical values for the soft-start capacitor range from 100nF to 1F. * Finally, the frequency foldback circuit reduces the maximum switching frequency when the FB pin is below 1V. This feature reduces the minimum duty cycle that the part can achieve thus allowing better control of the switch current during start-up. Power-On Reset and Watchdog Timer Operation The LT8495 has a power-on reset (POR) circuit and a reset timer to assert the RST pin for a minimum amount of time. After initial power up the open-drain RST pin is asserted low for a programmable reset delay time (see the Timing Diagrams). During normal operation, the RST pin can also be asserted when either the RSTIN pin is below its threshold or the chip enters shutdown due to an abnormal condition. After the chip exits shutdown and the RSTIN pin rises above its threshold, the RST pin is released after the reset delay time which is programmable through the CPOR pin. The watchdog timer typically monitors a microcontroller's activity. The watchdog timer can be enabled or disabled by applying a logic signal to the WDE pin. When enabled, the watchdog timer requires successive negative edges on the WDI pin to happen within a programmed time window to keep WDO from pulsing low. Therefore, if the time between the two negative WDI edges is too short or too long, the WDO pin will be pulsed low. When the WDO pin pulls low, a reset timer keeps the WDO pin low for a delay programmed by the CPOR pin. The WDO pin will go high again after the reset timer expires or the chip shuts down (see the Timing Diagrams). The window periods can be set through the CWDT pin. 8495fa 12 For more information www.linear.com/LT8495 LT8495 APPLICATIONS INFORMATION Low Ripple Burst Mode Operation To enhance efficiency at light loads, the LT8495 regulator enters low ripple Burst Mode operation keeping the output capacitor charged to the proper voltage while minimizing the input quiescent current. During Burst Mode operation, the LT8495 regulator delivers single-cycle bursts of current to the output capacitor with each followed by a sleep period where the output power is delivered to the load by the output capacitor. The quiescent currents of VIN/BIAS are reduced to less than 3A to 6A typically during the sleep time (see Electrical Characteristics table). As the load current decreases towards a no-load condition, the frequency of single current pulses decreases (see Figure 1), therefore the percentage of time that the LT8495 operates in sleep mode increases, resulting in reduced average input current and thus high efficiency even at very low loads. By maximizing the time between pulses, the LT8495 quiescent current is minimized. Therefore, to optimize the quiescent current performance at light loads, the current in the feedback resistor divider and the reverse current in the external diode must be minimized, as these appear to the output as load currents. More specifically, during SWITCHING FREQUENCY (kHz) 500 FRONT PAGE APPLICATION 400 300 200 100 0 0.1 1 10 100 LOAD CURRENT (mA) the sleep time, the boost converter has the reverse diode leakage current conducting from output to input, while the SEPIC converter has leakage current conducting from output to ground. Use the largest possible feedback resistors and a low leakage Schottky diode in applications with ultralow Q current. In Burst Mode operation, the burst frequency and the charge delivered with each pulse will not change with output capacitance. Therefore, the output voltage ripple will be inversely proportional to the output capacitance. In a typical application with a 47F output capacitor, the output ripple is about 10mV and with two 47F output capacitors the output ripple is about 5mV (see Switching Waveforms, Burst Mode Operation in Typical Performance Characteristics section). The output voltage ripple can continue to be decreased by increasing the output capacitance. At higher output loads the LT8495 regulator runs at the frequency programmed by the RT resistor and operates as a standard current mode regulator. The transition between high current mode and low ripple Burst Mode operation is seamless, and will not disturb the output voltage. Chip Enable Pins The SWEN, WDE and RSTIN pins are used to enable various portions of the LT8495. The lowest current state is when all three pins are at 0V which disables all functions of the LT8495. Raising any of these pins above their respective input threshold voltages (see Electrical Characteristics section) activates the core circuits of the LT8495. Start-up of the LT8495 core circuits typically requires about 1ms (see the Timing Diagram). See the sections Enabling the Switching Regulator, Watchdog Timer, and Reset Conditions for further details about SWEN, WDE and RSTIN respectively. 1000 Enabling the Switching Regulator 8495 F01 Figure 1. Switching Frequency in Burst Mode Operation The SWEN pin is used to enable or disable the switching regulator. This pin operates independently of the watchdog enable (WDE) and the RST control input (RSTIN). The rising threshold of SWEN is typically 1V, with 30mV of hysteresis. The switching regulator is disabled by driving the SWEN pin below this threshold which deactivates the NPN power switch. The switching regulator is enabled by 8495fa For more information www.linear.com/LT8495 13 LT8495 APPLICATIONS INFORMATION driving SWEN above its threshold. Before active switching begins, the soft-start capacitor is quickly discharged then slowly charged causing a gradual start-up of the regulator. SWEN can be connected to VIN if "always on" operation is desired, although some current will flow into the SWEN pin (see Typical Performance Characteristics) increasing overall bias current of the system. Also, a resistor divider can be connected to SWEN to create an undervoltage lockout function (see Undervoltage Lockouts) for more information. Setting the Output Voltage The output voltage is programmed with a resistor divider from output to the FB pin (R2) and from the FB pin to ground (R1). Choose the 1% resistors according to: V R2 = R1 OUT - 1 1.202 Note that choosing larger resistors decreases the quiescent current of the application circuits. In low load applications, choosing larger resistors is more critical since the part enters Burst Mode operation with lower quiescent current. Power Switch Duty Cycle In order to maintain loop stability and deliver adequate current to the load, the power NPN (Q1 in the Block Diagram) cannot remain "on" for 100% of each clock cycle. The maximum allowable duty cycle is given by: T -Minimum Switch Off-Time DCMAX = P *100% TP where TP is the clock period and the Minimum Switch Off-Time (found in the Electrical Characteristics) is typically 70ns. Conversely, the power NPNs (Q1 in the Block Diagram) cannot remain "off" for 100% of each clock cycle, and will turn on for a minimum time (Minimum Switch OnTime) when in regulation. This Minimum Switch On-Time governs the minimum allowable duty cycle given by: DCMIN = where TP is the clock period and Minimum Switch On-Time (found in the Electrical Characteristics) is typically 95ns. The application should be designed such that the operating duty cycle (DC) is between DCMIN and DCMAX. Normally, DC rises with higher VOUT and lower VIN. Duty cycle equations for both boost and SEPIC topologies are given below, where VD is the diode forward voltage drop and VCESAT is typically 340mV at 1.2A. For the boost topology: V -V +V DC OUT IN D VOUT + VD - VCESAT For the SEPIC topology: VOUT + VD DC VIN + VOUT + VD - VCESAT The LT8495 can be used in configurations where the duty cycle is higher than DCMAX, but it must be operated in the discontinuous conduction mode or Burst Mode operation so that the effective duty cycle is reduced. Setting the Switching Frequency The LT8495 uses a constant frequency PWM architecture that can be programmed to switch from 250kHz to 1.5MHz by using a resistor tied from the RT pin to ground. Table 1 shows the necessary RT values for various switching frequencies. Table 1. Switching Frequency vs RT Value SWITCHING FREQUENCY (MHz) RT VALUE (k) 0.25 324 0.4 196 0.6 124 0.8 88.7 1.0 68.1 1.2 54.9 1.4 45.3 1.5 41.2 Minimum Switch On-Time *100% TP 8495fa 14 For more information www.linear.com/LT8495 LT8495 APPLICATIONS INFORMATION where: Inductor Selection General Guidelines: The high frequency operation of the LT8495 allows for the use of small surface mount inductors. For high efficiency, choose inductors with high frequency core material, such as ferrite, to reduce core losses. To improve efficiency, choose inductors with more volume for a given inductance. The inductor should have low DCR (copper wire resistance) to reduce I2R losses, and must be able to handle the peak inductor current without saturating. Note that in some applications, the current handling requirements of the inductor can be lower, such as in the SEPIC topology when using uncoupled inductors, where each inductor only carries a fraction of the total switch current. Molded chokes or chip inductors usually do not have enough core area to support peak inductor currents in the 2A to 3A range. To minimize radiated noise, use a toroidal or shielded inductor. Note that the inductance of shielded types will drop more as current increases, and will saturate more easily. Minimum Inductance: Although there can be a trade-off with efficiency, it is often desirable to minimize board space by choosing smaller inductors. When choosing an inductor, there are two conditions that limit the minimum inductance; (1) providing adequate load current, and (2) avoidance of subharmonic oscillation. Choose an inductance that is high enough to meet both of these requirements. Adequate Load Current: Small value inductors result in increased ripple currents and thus, due to the limited peak switch current, decrease the average current that can be provided to a load (IOUT). In order to provide adequate load current, L should be at least: L> DC * VIN V *I 2 ( f ) ILIM - OUT OUT VIN * For boost topologies, or: L> DC * VIN V *I 2 ( f ) ILIM - OUT OUT -IOUT VIN * L = L1||L2 for uncoupled SEPIC topology DC = switch duty cycle (see previous section) ILIM = switch current limit, typically about 2.35A at 50% duty cycle (see the Typical Performance Characteristics section) = power conversion efficiency (typically 85% to 90% for boost and 80% to 85% for SEPIC at high currents) f = switching frequency Negative values of L indicate that the output load current IOUT exceeds the switch current limit capability of the LT8495. Avoiding Subharmonic Oscillations: The internal slope compensation circuit of LT8495 helps prevent the subharmonic oscillations that can occur when the duty cycle is greater than 50%, provided that the inductance exceeds a minimum value. In applications that operate with duty cycles greater than 50%, the inductance must be at least: L> ( VIN - VCESAT ) * (2DC- 1) 0.76 * (1.5 *DC+1) * f * (1-DC) for boost and coupled inductor SEPIC, or: L1||L2 > ( VIN - VCESAT ) * (2DC- 1) 0.76 * (1.5 *DC+1) * f * (1-DC) for the uncoupled inductor SEPIC topologies. Maximum Inductance: Excessive inductance can reduce current ripple to levels that are difficult for the current comparator (A2 in the Block Diagram) to cleanly discriminate, thus causing duty cycle jitter and/or poor regulation. The maximum inductance can be calculated by: LMAX = VIN - VCESAT DC * IMIN(RIPPLE) f where LMAX is L1||L2 for uncoupled SEPIC topologies and IMIN(RIPPLE) is typically 150mA. for the SEPIC topologies. 8495fa For more information www.linear.com/LT8495 15 LT8495 APPLICATIONS INFORMATION Current Rating: Finally, the inductor(s) must have a rating greater than its peak operating current to prevent inductor saturation resulting in efficiency loss. In steady state, the peak and average input inductor currents (continuous conduction mode only) is given by: IL1(PEAK) = IL1(AVG) = VOUT *IOUT VIN *DC + VIN * 2 *L1* f VOUT *IOUT VIN * for the boost and uncoupled inductor SEPIC topology. For uncoupled SEPIC topologies, the peak and average currents of the output inductor L2 is given by: IL2(PEAK) =IOUT + VOUT * (1-DC) 2 *L2 * f IL2(AVG) =IOUT For the coupled inductor SEPIC: V V *DC IL(PEAK) =IOUT * 1+ OUT + IN VIN * 2 *L * f to 20F, particularly 0805 or 0603 case sizes, have greatly reduced capacitance at the desired output voltage. Solid tantalum or OS-CON capacitors can be used, but they will occupy more board area than a ceramic and will have a higher ESR with greater output ripple. Ceramic capacitors also make a good choice for the input decoupling capacitor, which should be placed as closely as possible to the VIN and BIAS pins of the LT8495. A 2.2F to 4.7F input capacitor is sufficient for most applications. Audible Noise Ceramic capacitors are small, robust and have very low ESR. However, due to their piezoelectric nature, ceramic capacitors can sometimes create audible noise when used with the LT8495. During Burst Mode operation, the LT8495 regulator's switching frequency depends on the load current, and at very light loads the regulator can excite the ceramic capacitor at audio frequencies, generating audible noise. Since LT8495 operates at a lower current limit during Burst Mode operation, the noise is typically very quiet. If this is unacceptable, use a high performance tantalum or electrolytic capacitor at the output. Diode Selection V IL(AVG) =IOUT * 1+ OUT VIN * Note: Inductor current can be higher during load transients. It can also be higher during short circuit and start-up if inadequate soft-start capacitance is used. Thus, IL(PEAK) may be higher than the switch current limit of 2.95A, and the RMS inductor current is approximately equal to IL(AVG). Choose an inductor having sufficient saturation current and RMS current ratings. Capacitor Selection Low ESR (equivalent series resistance) capacitors should be used at the output to minimize the output ripple voltage. Multilayer ceramic capacitors are an excellent choice, as they have an extremely low ESR and are available in very small packages. X5R or X7R dielectrics are preferred, as these materials retain their capacitance over wider voltage and temperature ranges. Always use a capacitor with a sufficient voltage rating. Many capacitors rated at 2.2F The diode used in boost or SEPIC topologies conducts current only during switch off-time. During switch on-time, the diode has reverse voltage across it. The peak reverse voltage is equal to VOUT in the boost topology and equal to (VOUT + VIN) in the SEPIC topology. Use a diode with a reverse voltage rating greater than the peak reverse voltage. An additional consideration is the reverse leakage current. The leakage current appears to the output as load current and affects the efficiency, most noticeably, under light load conditions. In Burst Mode operation, after the inductor current vanishes, the reverse voltage across the boost diode is approximately equal to VOUT - VIN in the boost topology and VOUT in the SEPIC topology. The percentage of time that the diode is reverse biased increases as load current decreases. Schottky diodes that have larger forward voltages often have less leakage, so a trade-off exists between light load and high load efficiency. Also the Schottky diodes with larger reverse bias ratings may have less leakage at a given output voltage, therefore, superior leakage performance can be 8495fa 16 For more information www.linear.com/LT8495 LT8495 APPLICATIONS INFORMATION achieved at the expense of diode size. Finally, keep in mind that the leakage current of a power Schottky diode goes up exponentially with junction temperature. Therefore, the Schottky diode must be selected with care to avoid excessive increase in light load supply current at high temperatures. Soft-Start The LT8495 contains a soft-start circuit to limit peak switch currents during start-up. High start-up current is inherent in switching regulators since the feedback loop is saturated due to VOUT being far from its final value. The regulator tries to charge the output capacitor as quickly as possible, which results in large peak currents. The start-up current can be limited by connecting an external capacitor (typically 100nF to 1F) to the SS pin. This capacitor is slowly charged to ~2.1V by an internal 256k resistor once the part is activated. SS pin voltages below ~0.8V reduce the internal current limit. Thus, the gradual ramping of the SS voltage also gradually increases the current limit as the capacitor charges. This, in turn, allows the output capacitor to charge gradually toward its final value while limiting the start-up current. When the switching regulator shuts down the soft-start capacitor is automatically discharged to ~100mV or less before charging resumes, thus assuring that the soft-start occurs after every reactivation of the switching regulation. Power Supplies and Operating Limits The LT8495 draws supply current from the VIN and BIAS pins. The largest supply current draw occurs when the switching regulator is enabled (SWEN is high) and the power switch is toggling on and off. Under light load conditions the switching regulator enters Burst Mode operation where the power switch toggles infrequently and the input current is significantly reduced (see the Low Ripple Burst Mode Operation section). Power Switch Driver (PSD) Operating Range: The NPN power switch is driven by a power switch driver (PSD) as shown in the Block Diagram. The driver must be powered by a supply (VIN or BIAS) that is above the minimum operating voltage and below the PSD overvoltage threshold. These voltages are typically 2.4V and 34V respectively (see Electrical Characteristics). If neither VIN nor BIAS is within this operating range, the PSD and the switching regulator are automatically disabled. Voltages up to 60V are not harmful to the PSD, however, as discussed, switching regulation is automatically disabled when neither VIN nor BIAS is in the valid operating range. See Table 2 for some example operating conditions. Reset and Watchdog Operating Voltage Limits: The reset circuits operate properly as long as either VIN or BIAS is above 1.3V (see Reset Conditions section). The watchdog timer operates properly when either VIN or BIAS is between 2.5V and 60V. The table below gives some example operating conditions. Table 2: Operating Condition Examples VIN (V) BIAS (V) RESET CIRCUITS SWITCHING WATCHDOG REGULATOR 0 1.3 X 1.3 0 X 1 40 X X 40 40 X X 1 30 X X X 12 40 X X X Automatic Power Supply Selection: In order to minimize power loss, the LT8495 draws as much of its required current as possible from the lowest suitable voltage supply (VIN or BIAS) in accordance with the requirements described in the previous two sections. This selection is automatic and can change as VIN and/or BIAS voltages change. The LT8495 compares the VIN and BIAS voltages to determine which is lower. The comparator has an offset and hysteresis as shown in the Electrical Characteristics section. The voltage comparison happens continuously when the power switch is toggling. The result of the latest comparison is latched inside the LT8495 when switching stops. If the power switch is not toggling, the LT8495 uses the last VIN vs BIAS comparison to determine which supply is lower. After initial power up or any thermal lockout the LT8495 always concludes that VIN is the lower supply voltage until subsequent voltage comparisons can be made while the power switch is toggling. BIAS Connection for SEPIC Converters: For SEPIC converters, where VIN can be above or below VOUT, BIAS is typically connected to VOUT which improves efficiency when 8495fa For more information www.linear.com/LT8495 17 LT8495 APPLICATIONS INFORMATION VIN voltage is higher than VOUT. Connecting BIAS to VOUT in a SEPIC topology also allows the switching regulator to operate with VIN above 34V (typical switch driver overvoltage threshold) in cases where VOUT is regulated below the PSD overvoltage threshold. Finally, connecting BIAS to VOUT also allows the converter to operate from VIN voltages less than 2.5V after VOUT rises within the PSD operating range. This can be very useful in battery powered applications since the battery voltage drops as it discharges. BIAS Connection for Boost Converters: For boost converters, BIAS is typically connected to VOUT or to ground. Connecting BIAS to VOUT allows the converter to operate with VIN < 2.5V after VOUT has risen within the PSD operating range. However, during no load conditions on VOUT, despite VIN being selected as the primary input supply, the overall power loss will be slightly elevated due to the small amount of current still being drawn from the higher voltage BIAS pin. To minimize boost converter power loss during no load conditions, connect BIAS instead to ground. For boost applications with VOUT higher than the PSD operating range, the BIAS pin should not typically be connected to VOUT. The LT8495 will never draw the majority of its current from BIAS due to the excessive voltage, therefore this connection does not help to improve efficiency. Alternative choices for the BIAS pin connection are ground or another supply that is within the PSD operating range. Maximum VIN for Boost Converters: VIN cannot generally be higher than VOUT in boost topologies because of the DC path from VIN to VOUT though the inductor and the output diode. If VIN must be higher than VOUT, then the inductor must be powered by a separate supply that is always below VOUT. Otherwise a SEPIC topology can be used. Also, the LT8495 will not operate in a boost topology with VIN voltages above the PSD operating range unless BIAS is connected to an alternative supply within the valid operating range. VIN/BIAS Ramp Rate: While initially powering a switching converter application, the VIN/BIAS ramp rate should be limited. High VIN/BIAS ramp rates can cause excessive inrush currents in the passive components of the converter. This can lead to current and/or voltage overstress and may damage the passive components or the chip. Ramping rates less than 500mV/s, depending on component parameters, will generally prevent these issues. Also, be careful to avoid hot plugging. Hot plugging occurs when an active voltage supply is "instantly" connected or switched to the input of the converter. Hot plugging results in very fast input ramp rates and is not recommended. Finally, for more information, refer to Linear Application Note 88, which discusses voltage overstress that can occur when inductive source impedance is hot plugged to an input pin bypassed by ceramic capacitors. Watchdog Timer The LT8495 includes an adjustable watchdog timer that can monitor a microcontroller activity. If a code execution error occurs, the watchdog timer can detect this and pull the open drain WDO pin low. WDO can be connected to RST or to another input of the microcontroller to reset or interrupt the microcontroller. Note that the pull-up resistor must be connected to WDO for proper operation. This resistor is often already integrated in the microcontroller. The watchdog circuitry monitors negative edges on the WDI pin. The WDI pin's negative going pulses are restricted to appear inside a programmed time window to prevent WDO from going low. During a code execution error, the microcontroller will generate WDI pulses that are either too fast or too slow which will cause WDO to assert low and force the microcontroller to reset the program (see the Timing Diagram section). While monitoring WDI, if the time between any two falling edges is shorter than the watchdog lower boundary, tWDL (see Figure 2), or longer than the watchdog upper boundary, tWDU (see Figure 3), WDO is pulled down for a programmable period of tRST (see Reset Conditions section). WDI 5V/DIV WDO 5V/DIV CWDT 1V/DIV tWDL = 5.2ms, CWDT = 10nF CPOR 1V/DIV 2ms/DIV 8495 F02 Figure 2. Window Watchdog Waveforms 8495fa 18 For more information www.linear.com/LT8495 LT8495 APPLICATIONS INFORMATION Thus, the WDI period should be higher than tWDL, and lower than tWDU to keep WDO high under normal conditions. WDO also pulls low if no negative WDI edge occurs during the watchdog upper boundary period. 0.064 0.058 K1 (nF/ms) WDI 2V/DIV WDO 5V/DIV 0.070 0.052 0.046 0.040 tWDU = 155ms, CWDT = 10nF CWDT 1V/DIV 0.034 0.1 tRST = 93ms, CPOR = 47nF CPOR 1V/DIV 1 10 100 1k 10k UPPER BOUNDARY PERIOD, t WDU (ms) 8495 F04 50ms/DIV 8495 F03 Figure 4. Watchdog Upper Boundary Parameter Figure 3. Timeout Watchdog Waveforms 1.6 To program the tWDU and tWDL periods, see the Watchdog Upper and Lower Boundary Periods vs Capacitance graphs in the Typical Characteristics section to select CWDT. The required capacitor value can also be calculated from a given watchdog timeout period by using the following equation: 1.3 K2 (ms/nF) Selecting the Watchdog Timing Capacitor: The watchdog timeout period is adjustable and can be optimized for software execution. The watchdog upper and lower boundary timeout periods (tWDU and tWDL) are adjusted by connecting a capacitor, CWDT, between the CWDT pin and ground. tWDU is typically 30 * tWDL for large CWDT values (greater than about 50nF). For lower values this ratio reduces as shown in Figure 6. 1.0 0.7 0.4 0.01 0.1 1 10 100 CWDT PIN CAPACITANCE, CWDT (nF) 1k 8495 F05 Figure 5. Watchdog Lower Boundary Parameter 32 CWDT = K1 * tWDU In addition, the following equation can be used to calculate the watchdog lower boundary period for a given CWDT capacitor value. tWDL = K2 * CWDT 28 K3 Where CWDT is the external capacitor value in nF, tWDU is the upper boundary period in ms, and K1 is their ratio with typical values shown in Figure 4. K1 can be approximated as 0.065nF/ms for upper boundaries greater than 50ms. 24 20 16 0.01 Where tWDL is the lower boundary in ms, CWDT is the external capacitance in nF, and K2 is their ratio with typical values shown in Figure 5. K2 can be approximated as 0.52ms/nF for CWDT values greater than 10nF. 0.1 1 10 100 CWDT PIN CAPACITANCE, CWDT (nF) 1k 8495 F06 Figure 6. Upper and Lower Boundary Ratio For more information www.linear.com/LT8495 8495fa 19 LT8495 APPLICATIONS INFORMATION The watchdog lower boundary period (tWDL) has a fixed relationship to tWDU for a given CWDT capacitance. The tWDL period is related to tWDU by the following relationship: tWDU = K3 * tWDL where K3 is the ratio between upper and lower boundary with typical values shown in Figure 6. Leaving the CWDT pin unconnected will generate a minimum watchdog timeout of approximately 270s. Maximum timeout is limited by the largest available low leakage capacitor. The Electrical Characteristics section indicates the guaranteed tolerance of the timeout period for a given capacitance. The accuracy of the timeout period will also be affected by capacitor leakage (the nominal charging current is 2.3A) and capacitor tolerance. A low leakage ceramic capacitor is recommended. Watchdog Timer Start-Up: There are several conditions when the WDI pin is not monitored by the watchdog timer. For each condition, the start-up or resumption of WDI pin monitoring occurs as described below: * The watchdog timer is disabled during the POR or thermal lockout. After POR and thermal lockout are cleared, CWDT will begin ramping from 0V. The WDI edges are ignored while the CWDT charges from 0V to ~200mV. * The watchdog is disabled when WDE is low. After WDE rises, CWDT may require 1s to 100s (typical) before starting to ramp up. The WDI edges are ignored until the CWDT charges from 0V to ~200mV. * WDI edges are not monitored while WDO is asserted low. Four CPOR cycles are required before WDO is released and CWDT begins ramping up. The WDI edges are ignored until the CWDT charges from 0V to ~200mV. If desired, the RST pin can be connected to WDE to enable the watchdog timer at about the same time RST is released. For the example shown in Figure 7, RST is connected to WDE. After the chip starts up, the output voltage ramps up towards 5V for the microcontroller supply. When VOUT rises above 4.5V, and thus RSTIN rises above 1.1V, the RST and WDE pins will be held low for the additional period of tRST. After tRST, RST is released and WDE will pull high, thus enabling the microcontroller and the watchdog timer at about the same time. LT8495 RSTIN 1.10V + - VOUT 374k RST CPOR 121k POR TIMER + - CWDT WATCHDOG TIMER 1.00V WDE WDI WDO VDD C RST WDI WDO 8495 F07 Figure 7. Watchdog Monitoring Reset Conditions The LT8495 has three reset conditions as described below. All of these conditions can cause the open-drain RST pin to pull low, as long as either VIN or BIAS is above 1.3V. A pull-up resistor can be connected to the RST pin so that it can be used as a reset for an external microcontroller or other devices. An adjustable timer delays the release of RST by tRST to ensure adequate reset duration for the external devices. The three reset conditions are as follows: * POR: The RST pin is asserted if VIN and BIAS are both below 2.4V (typical). This is the power-on reset condition which causes RST to assert upon initial power up of the LT8495 (see Timing Diagrams). Under this condition the switching regulator and watchdog timer are disabled and the CWDT, CPOR, and SS capacitors are discharged to ground. * Thermal Lockout: An overtemperature condition on the LT8495 die will cause the RST pin to assert low. See High Temperature Considerations section for additional information. This condition disables the switching regulator, the watchdog timer and discharges the CWDT, CPOR, and SS capacitors to ground. See Thermal Lockout section for additional information. 8495fa 20 For more information www.linear.com/LT8495 LT8495 APPLICATIONS INFORMATION A programmable timer delays the release of RST by tRST after all of the above reset conditions are no longer met. Before releasing RST, the external CPOR capacitor ramps up and down for four cycles creating the tRST delay (see Figure 8). To program the tRST period, see the Reset Timeout Period vs Capacitance graphs in the Typical Characteristics section to select CPOR. The required capacitor value can also be calculated from a given reset timeout period by using the following equation: CPOR = K4 * tRST RSTIN 5V/DIV RST 5V/DIV tRST = 93ms, CPOR = 47nF CPOR 500mV/DIV 20ms/DIV 8495 F08 Figure 8. Reset Timer Waveforms 0.6 0.5 K4 (nF/ms) * RSTIN Undervoltage Lockout: The open-drain RST pin is asserted low if the RSTIN input is below the 1.1V typical threshold (see Electrical Characteristics). This function enables the use of an external resistor divider to configure an under voltage detection circuit. This reset condition has no effect on the switching regulator or the watchdog timer. See the Undervoltage Lockouts section for more information. 0.4 0.3 where CPOR is the external capacitor value in nF. tRST is the reset timeout period in ms, and K4 is their ratio with typical values shown in Figure 9, K4 can be approximated as 0.51nF/ms for reset timeout periods greater than 15ms. As described previously, this same timer is used to determine how long WDO is asserted low during a watchdog timeout. As an example, to create a 9.5ms tRST timeout period, choose a CPOR capacitor value of 4.7nF. Leaving the CPOR pin unconnected will generate a tRST period of approximately 40s. The maximum period is limited by the largest available low leakage capacitor. The Electrical Characteristics section indicates the guaranteed tolerance of the timeout period for a given capacitance. The accuracy of the timeout period will also be affected by capacitor leakage (the nominal charging current is 2.3A) and capacitor tolerance. A low leakage ceramic capacitor is recommended. As discussed previously, WDO is asserted low for a period of tRST after a watchdog error occurs. This period is measured by counting four cycles on the CPOR pin in the same way that the reset delay is measured. If a watchdog timeout occurs at the same time as the reset delay period, 0.2 0.1 1 10 100 RESET TIMEOUT PERIOD, tRST(ms) 1k 8495 F09 Figure 9. Reset Timer Parameter the watchdog takes priority in the counter. Therefore, WDO is always asserted low for four cycles of the CPOR pin, while the RST delay may be extended beyond four cycles to a maximum of six cycles, thus increasing tRST by up to 50%. Finally note that the tRST delay on the RST pin does not affect the switching regulator or watchdog timer. The switching regulator and/or watchdog timer will start right after the part is no longer in the POR or thermal lockout condition. Undervoltage Lockouts Undervoltage lockout (UVLO) functions can be implemented using the SWEN and/or RSTIN pins. An undervoltage lockout can shut down appropriate circuitry to prevent undesired operation when input and/or output voltages are too low. 8495fa For more information www.linear.com/LT8495 21 LT8495 APPLICATIONS INFORMATION R4 1M R3 487k SWEN 1.00V VC - + 2.1V 256k SS 8495 F10 Figure 10. VIN Undervoltage Lockout Input UVLO: Connecting a resistor divider from VIN to SWEN (see Figure 10) implements an input undervoltage lockout circuit. SWEN has an accurate rising threshold of 1.0V with 30mV of hysteresis (typical-see Electrical Specifications). By connecting a resistor divider from VIN to SWEN, the LT8495 will be programmed to disable the switching regulator when VIN drops below a desired threshold. Typically, this threshold is used in situations where the input supply is current limited, or has a relatively high source resistance. A switching regulator draws constant power from the source, so source current increases as source voltage drops. This looks like a negative resistance load to the source and can cause the source to current limit or latch low under low source voltage conditions. The input UVLO prevents the regulator from operating at source voltages where the problems might occur. As shown in Figure 10, by connecting a resistor divider from VIN to SWEN, the falling undervoltage lockout threshold is set to: VIN(UVLO) = R3+R4 * 0.97V R3 From the previous equation, the resistor divider shown in Figure 10 gives the VIN pin a falling undervoltage lockout threshold of 2.96V. When VIN is below this threshold, the switching regulation is disabled and the SS pin starts to discharge. After choosing the value of R3, for example, R4 can be calculated using: VIN(UVLO) R4 = R3 * - 1 0.97 Output UVLO: Connecting the RST and RSTIN pins as shown in Figures 11 and 12 implements an output undervoltage lock out (UVLO) circuit. This circuit resets VOUT powered devices when VOUT is below a desired voltage by asserting the open drain RST pin low. Note that a pull-up resistor is required on the RST pin, but might already be integrated in the C. There is typically a 23s delay from the RSTIN pin falling edge until RST is asserted low (see Electrical Characteristics section) for glitch immunity of the RSTIN pin. After RSTIN rises above its threshold, RST continues to be asserted low for a delayed time programmable by the CPOR pin capacitor. LT8495 POR TIMER VOUT R2B 1M R2A 8.87k R1 316k VOUT RST EN 2.3A - + LT8495 VIN CPOR 1.10V RSTIN FB 1.202V VDD C CPOR - + 23A VC 8495 F11 Figure 11. RSTIN Reset Lockout As shown in Figure 12, the R2 resistor (calculated in the Setting the Output Voltage section) is divided into two resistors, R2A & R2B to implement the UVLO function. Next, the following equations are used to calculate their values. 92% R2A = R1* - 1 UVLO%NOM R2B = R2 -R2A where UVLO%NOM is the desired nominal UVLO threshold voltage as a percentage of the nominal VOUT. UVLO%NOM is recommended to be 89.5% or less for most applications. Continue reading for more information about selecting UVLO%NOM. 8495fa 22 For more information www.linear.com/LT8495 LT8495 APPLICATIONS INFORMATION VOUT High Temperature Considerations VOUT R2B RSTIN R2 R2A FB R1 FB R1 8495 F12 Figure 12. RSTIN Pin Connection Options When choosing UVLO%NOM, consider that the transient response to VOUT load current steps may cause undershoot of VOUT. Excessive VOUT undershoot can cause RSTIN to drop below the comparator threshold and activate RST. The following equation includes the maximum RSTIN comparator threshold (97% of the FB reference - see Electrical Characteristics) to show what the maximum UVLO threshold can be. 97 92 For example, when choosing UVLO%NOM = 89.5%, UVLO%MAX = 94.36% of VOUT. Therefore the RST pin may assert if VOUT undershoots more than 5.64% below its steady-state regulated voltage. Choose a lower UVLO%NOM if more margin is required. UVLO%MAX = UVLO%NOM * In addition, the choice of UVLO%NOM affects the minimum possible VOUT voltage before RST is asserted. 86 92 For example, when using UVLO%NOM = 89.5%, UVLO%MIN = 83.66% of VOUT. Therefore the RST pin may not assert unless VOUT is 16.34% below its nominal value. Note that in terms of absolute VOUT UVLO voltage one must also consider the tolerance of the FB regulation voltage and the R1, R2A and R2B resistor tolerances. UVLO%MIN = UVLO%NOM * In the example shown in Figure 11, VOUT is regulated to 5V. For a desired UVLO% of 89.5%, the calculated R1, R2A, and R2B values are 316k, 8.87k, and 1M respectively. POR UVLO: When both VIN and BIAS are too low for proper LT8495 operation (typically <2.4V), the switching regulator and watchdog timers are disabled. For more information see the Reset Conditions section. For higher ambient temperatures, care should be taken in the layout of the PCB to ensure good heat sinking of the LT8495. The exposed pad on the bottom of the package must be soldered to a ground plane. This ground should be tied to large copper layers below with thermal vias; these layers will spread heat dissipated by the LT8495. Placing additional vias can reduce thermal resistance further. The maximum load current should be derated as the ambient temperature approaches the maximum junction rating. Power dissipation within the LT8495 is estimated by calculating the total power loss from an efficiency measurement and subtracting the diode loss, FB resistor loss and inductor loss. The die temperature is calculated by multiplying the LT8495 power dissipation by the thermal resistance from junction to ambient. The power switch and its driver dissipate the most power in the LT8495 (see Block Diagram). Higher switch current, duty cycle and output voltage result in higher die temperature. Power loss in the Power Switch Driver also increases with higher input supply voltage. The PSD is supplied by the lowest suitable voltage on VIN and BIAS. Connecting BIAS to a low voltage supply, often VOUT, can reduce the maximum die temperature of the LT8495 (see Automatic Power Supply Selection section). Also note that leakage current into the SWEN, RSTIN, WDE, and FB pins increases at high junction temperatures (see Typical Performance Characteristics). The potential leakage current should be considered when choosing high value resistors connected to those pins. Thermal Lockout: If the die temperature reaches approximately 165C, the part will go into thermal lockout and the chip will be reset. The part will be enabled again when the die temperature has dropped by ~5C (nominal). See the Reset Conditions section for more details about the chip's state during thermal lockout Fault Tolerance The LT8495 is designed to tolerate single fault condition in the TSSOP package. Shorting two adjacent pins together or leaving one single pin floating does not raise VOUT or cause damage to the LT8495 regulator. 8495fa For more information www.linear.com/LT8495 23 LT8495 APPLICATIONS INFORMATION Table 3 and Table 4 show the effects that result from shorting adjacent pins and from a floating pin, respectively. The NC pins must be left floating to ensure fault tolerance. For the best fault tolerance to inadvertent adjacent pin shorts, the BIAS pin must be tied to something higher than 1.230V or to the output to avoid overvoltage during a short from FB to BIAS. Table 3. Effects of Pin Shorts (TSSOP) PIN # EFFECT ON OUTPUT 1-2 Output voltage will fall to approximately 1.202V if BIAS is connected to the output. CPOR-CWDT 5-6 No effect on output. CWDT-RST 6-7 No effect on output. RST-SS 7-8 No effect or output will fall below regulation. RSTIN-SWEN 11-12 No effect on output. SWEN-WDE 12-13 No effect on output. WDE-GND 13-14 No effect on output. GND-WDO 14-15 No effect on output. WDO-WDI 15-16 No effect on output. Table 4.Effects of Floating Pins (TSSOP) PIN NAME BIAS FB PIN # 1 2-3 EFFECT ON OUTPUT Depending on the VIN voltage and the circuit topology, floating this pin will degrade device performance or the output will fall below regulation. As with all high frequency switchers, when considering layout, care must be taken to achieve optimal electrical, thermal and noise performance. One will not get advertised performance with a careless layout. For maximum efficiency, switch rise and fall times are typically in the 5ns to 10ns range. To prevent noise, both radiated and conducted, the high speed switching current paths, shown in Figures 13 & 14, must be kept as short as possible. This is implemented in the suggested PCB layouts in Figures 15 & 16. Shortening this path will also reduce the parasitic trace inductance. At switch-off, this parasitic inductance produces a flyback spike across the LT8495 switch. When operating at higher currents and output voltages, with poor layout, this spike can generate voltages across the LT8495 that may exceed its absolute maximum rating. A ground plane should also be used under the switcher circuitry to prevent interplane coupling and overall noise. The FB components should be kept as far away as practical from the switch node. The ground for these components should be separated from the switch current path. Failure to do so can result in poor stability or subharmonic oscillation. D1 L1 No effect if the other FB pad is soldered. VOUT SW CPOR 5 No effect on output. CWDT 6 No effect on output. RST 7 No effect on output. SS 8 No effect after part has started. Can potentially lead to an increase of inrush current during start-up. RT 10 Output may fall below regulation. RSTIN 11 No effect on output. SWEN 12 Enable state of the pin becomes undefined. Output will not exceed regulation voltage. WDE 13 No effect on output. GND 14 No effect if Exposed Pad is soldered. WDO 15 No effect on output. WDI 16 No effect on output. VIN 18 Depending on the BIAS voltage and the circuit topology, floating this pin will degrade device performance or the output will fall below regulation. VIN LT8495 C1 HIGH FREQUENCY SWITCHING PATH C2 LOAD GND 8495 F13 Figure 13. High Speed Chopped Switching Path for Boost Topology * 10 Output will fall below regulation voltage. Exposed Pad 21 Output maintains regulation, but potential degradation of device performance. D1 VOUT SW VIN SW C2 L1 LT8495 C1 HIGH FREQUENCY SWITCHING PATH L2 C3 LOAD * PIN NAMES FB-BIAS Layout Hints GND 8495 F14 Figure 14. High Speed Chopped Switching Path for SEPIC Topology 8495fa 24 For more information www.linear.com/LT8495 LT8495 APPLICATIONS INFORMATION VOUT D1 C2 RSTIN FB 1 SW 20 2 19 3 18 4 17 CPOR 5 CWDT 6 RST 7 SS RT L1 VIN C1 16 WDI 15 WDO 14 GND 8 13 WDE 9 12 SWEN 10 11 21 RSTIN 8495 F15 VIAS TO GROUND PLANE Figure 15. Suggested Component Placement for Boost Topology. Pin 21 (Exposed Pad) Must Be Soldered Directly to the Local Ground Plane for Adequate Thermal Performance. Multiple Vias to Additional Ground Planes Will Improve Thermal Performance D1 VOUT * C3 * L2 L1 C2 RSTIN FB 1 20 2 19 3 18 4 17 CPOR 5 CWDT 6 RST SS RT SW VIN 16 WDI 15 WDO 7 14 GND 8 13 WDE 9 12 SWEN 10 11 21 C1 RSTIN 8495 F16 VIAS TO GROUND PLANE Figure 16. Suggested Component Placement for SEPIC Topology. Pin 21 (Exposed Pad) Must Be Soldered Directly to the Local Ground Plane for Adequate Thermal Performance. Multiple Vias to Additional Ground Planes Will Improve Thermal Performance 8495fa For more information www.linear.com/LT8495 25 LT8495 TYPICAL APPLICATIONS 750kHz, 16V to 32V Input, 48V Output, 0.5A Boost Converter VIN 16V TO 32V L1 22H C1 2.2F D1 C2 4.7F x2 1M SW VIN 715 FB CPOR CWDT 4.7nF SS 1nF 10pF RSTIN SWEN 25.5k BIAS LT8495 GND WDO RT 0.2F VOUT 48V 0.5A WDE C RST 93.1k WDI 8495 TA02 C1: 2.2F, 50V, X5R, 1206 L1: WURTH LHMI 74437349220 D1: ONSEMI MBRA2H100 C2: 4.7F, 100V, X7R, 1210 Efficiency, VIN = 24V 100 EFFICIENCY (%) 95 90 85 80 75 70 0 100 200 300 400 LOAD CURRENT (mA) 500 8495 TA02b Transient Response with 400mA to 500mA to 400mA Output Load Step Start-Up Waveforms VOUT 0.5V/DIV AC COUPLED VOUT 20V/DIV VSS 0.5V/DIV IL 0.5A/DIV IL 0.5A/DIV VIN = 24V 200ms/DIV 8495 TA02c 96 LOAD VIN = 24V 5ms/DIV 8495 TA02d 8495fa 26 For more information www.linear.com/LT8495 LT8495 TYPICAL APPLICATIONS Wide Input and Output Range SEPIC Converter with Charge Pump Switches at 400kHz D1 C8 10F x2 D2 C10 10F VOUT 20V TO 60V 80mA D3 C7 10F x2 D4 C9 10F D7 1M R1 1.2 VIN 6V TO 38V (6V TO 32V FOR START-UP) D6 C3 3.3F L1 22H C1 2.2F D5 C2 10F x2 L2 22H VIN SW BIAS RSTIN SWEN LT8495 WDE RT WDI 196k GND SS DAC 78.7k WDO CWDT RST C5 1nF 0.1V TO 3.2V FB CPOR C4 4.7nF OUTPUT ADJUST 1k (SET DAC TO 3.2V FOR START-UP) C 26.7k 1F 8495 TA03 L1, L2: COILCRAFT MSD1260T-223ML C1: 2.2F, 50V, X5R,1206 C3: 3.3F, 100V, X7R, 1210 C2, C7-C10: TAIYO YUDEN GMK325C7106KMHT, 10F, 35V, X7S, 1210 C4: 4.7nF, 25V, NP0, 0603 C5: 1nF, 25V, NP0, 0603 D1-D4: FAIRCHILD MBR0540 D5-D7: ON-SEMI MBRA2H100 R1: 1.2, 0.5W, SMD, 2010 8495fa For more information www.linear.com/LT8495 27 LT8495 TYPICAL APPLICATIONS Li-Ion to 12V, Low Q Current Boost @ 650kHz L1 6.8H VIN 2.8V TO 4.1V D1 C1 4.7F 1M SW VIN 10pF RSTIN 3.09k SWEN FB CPOR 110k CWDT 4.7nF WDO RT 1F GND LT8495 SS 1nF VOUT 12V C2 200mA 47F WDE BIAS C RST 113k WDI 8495 TA04 C1: 4.7F, 6.3V, X7R, 1206 C2: 47F, 16V, X5R, 1210 D1: ONSEMI MBRM120LT1G L1: WURTH 74437346068 Efficiency, VIN = 3.3V 95 90 EFFICIENCY (%) 85 80 75 70 65 60 55 0.2 1 10 LOAD CURRENT (mA) 100 200 8495 G17 8495fa 28 For more information www.linear.com/LT8495 LT8495 TYPICAL APPLICATIONS Low Q Current, 5V to 300V, 250kHz Flyback Converter Danger High Voltage! Operation by High Voltage Trained Personnel Only T1 1:5 VIN 5V D1 * C1 2.2F 1M 14.7H D2 VOUT 300V 2mA KEEP MAXIMUM OUTPUT POWER AT 0.6W 1M * 1M VIN SW RSTIN FB SWEN CPOR CWDT 4.7nF SS 1nF RT 1F 324kHz BIAS LT8495 C2 22nF 340 12.1k GND WDO WDE C RST WDI C1: 2.2F, 25V, X5R, 1206 8495 TA05 C2: TDK C3225CH2J223K D1: VISHAY GSD2004S DUAL DIODE CONNECTED IN SERIES D2: ONSEMI MBRA2H100 T1: WE -FLEX TRANSFORMER 749196121 Start-Up Waveforms Switching Waveforms VOUT 0.5V/DIV IPRIMARY 0.5A/DIV IPRIMARY 1A/DIV VOUT 50V/DIV 2mA LOAD 5ms/DIV 8495 TA05b 2mA LOAD 2s/DIV 8495 TA05c 8495fa For more information www.linear.com/LT8495 29 LT8495 TYPICAL APPLICATIONS 450kHz, 5V Output SEPIC Converter (Same as Front Page Application) L1 15H VIN 3V TO 60V * C3 2.2F * C1 2.2F 1M L2 15H SW SWEN LT8495 WDO WDE RT 1F 8.87k 316k SS 4.7nF C2 47F x2 GND CPOR 1nF 4.7pF BIAS RSTIN FB VIN CWDT VOUT 5V 0.4A (VIN = 3V) 0.6A (VIN = 5V) 1.0A (VIN > 12V) D1 C RST 169k WDI 8495 TA07 C1, C3: 2.2F, 100V, X5R, 1206 C2: TAIYO YUDEN, EMK325BJ476MM-T D1: ONSEMI MBRA2H100 L1, L2: COILTRONICS DRQ125-150-R 1.5MHz, 12V Output SEPIC Converter VIN 9V TO 16V * C3 2.2F C1 2.2F D1 * SW CPOR SS RT 4.7nF 1F 41.2k Efficiency, VIN = 12V C2 10F x2 85 110k LT8495 WDO RST EFFICIENCY 80 GND WDE 1200 90 3.09k C 900 75 70 600 POWER LOSS 65 300 60 WDI POWER LOSS (mW) CWDT 47pF BIAS RSTIN FB SWEN 1nF 1M L2 4.7H VIN VOUT 12V 0.5A EFFICIENCY (%) L1 4.7H 55 8495 TA08a C1, C3: 2.2F, 50V, X5R, 1206 C2: TAIYO YUDEN, TMK325BJ106MM D1: CENTRAL SEMI CMMSH2-40 L1, L2: COILTRONICS DRQ74-4R7 50 0 100 200 300 400 LOAD CURRENT (mA) 0 500 8495 TA08b 8495fa 30 For more information www.linear.com/LT8495 LT8495 PACKAGE DESCRIPTION Please refer to http://www.linear.com/designtools/packaging/ for the most recent package drawings. FE Package 20-Lead Plastic TSSOP (4.4mm) (Reference LTC DWG # 05-08-1663 Rev K) Exposed Pad Variation CB DETAIL A 6.40 - 6.60* (.252 - .260) 3.86 (.152) 3.86 (.152) 0.60 (.024) REF 0.28 (.011) REF 20 1918 17 16 15 14 13 12 11 6.60 0.10 2.74 (.108) 4.50 0.10 DETAIL A 6.40 2.74 (.252) (.108) BSC SEE NOTE 4 0.45 0.05 DETAIL A IS THE PART OF THE LEAD FRAME FEATURE FOR REFERENCE ONLY NO MEASUREMENT PURPOSE 1.05 0.10 0.65 BSC 1 2 3 4 5 6 7 8 9 10 RECOMMENDED SOLDER PAD LAYOUT 4.30 - 4.50* (.169 - .177) 0.09 - 0.20 (.0035 - .0079) 0.25 REF 0.50 - 0.75 (.020 - .030) NOTE: 1. CONTROLLING DIMENSION: MILLIMETERS MILLIMETERS 2. DIMENSIONS ARE IN (INCHES) 3. DRAWING NOT TO SCALE 1.20 (.047) MAX 0 - 8 0.65 (.0256) BSC 0.195 - 0.30 (.0077 - .0118) TYP 0.05 - 0.15 (.002 - .006) FE20 (CB) TSSOP REV K 0913 4. RECOMMENDED MINIMUM PCB METAL SIZE FOR EXPOSED PAD ATTACHMENT *DIMENSIONS DO NOT INCLUDE MOLD FLASH. MOLD FLASH SHALL NOT EXCEED 0.150mm (.006") PER SIDE 8495fa For more information www.linear.com/LT8495 31 LT8495 PACKAGE DESCRIPTION Please refer to http://www.linear.com/designtools/packaging/ for the most recent package drawings. UF Package 20-Lead Plastic QFN (4mm x 4mm) (Reference LTC DWG # 05-08-1710 Rev A) 0.70 0.05 4.50 0.05 3.10 0.05 2.00 REF 2.45 0.05 2.45 0.05 PACKAGE OUTLINE 0.25 0.05 0.50 BSC RECOMMENDED SOLDER PAD PITCH AND DIMENSIONS APPLY SOLDER MASK TO AREAS THAT ARE NOT SOLDERED 4.00 0.10 0.75 0.05 R = 0.05 TYP R = 0.115 TYP 19 20 0.40 0.10 PIN 1 TOP MARK (NOTE 6) 4.00 0.10 PIN 1 NOTCH R = 0.20 TYP OR 0.35 x 45 CHAMFER BOTTOM VIEW--EXPOSED PAD 1 2.00 REF 2.45 0.10 2 2.45 0.10 (UF20) QFN 01-07 REV A 0.200 REF 0.00 - 0.05 0.25 0.05 0.50 BSC NOTE: 1. DRAWING IS PROPOSED TO BE MADE A JEDEC PACKAGE OUTLINE MO-220 VARIATION (WGGD-1)--TO BE APPROVED 2. DRAWING NOT TO SCALE 3. ALL DIMENSIONS ARE IN MILLIMETERS 4. DIMENSIONS OF EXPOSED PAD ON BOTTOM OF PACKAGE DO NOT INCLUDE MOLD FLASH. MOLD FLASH, IF PRESENT, SHALL NOT EXCEED 0.15mm ON ANY SIDE 5. EXPOSED PAD SHALL BE SOLDER PLATED 6. SHADED AREA IS ONLY A REFERENCE FOR PIN 1 LOCATION ON THE TOP AND BOTTOM OF PACKAGE 8495fa 32 For more information www.linear.com/LT8495 LT8495 REVISION HISTORY REV DATE DESCRIPTION A 07/15 Added QFN package option. PAGE NUMBER Added QFN package option and H-Grade option in TSSOP. 1 2, 3, 4, 9 Clarified Quiescent Current specifications. 3 Clarified RST Leakage Current specifications. 4 Added Pin Current and Quiescent Current graphs. 8 Clarified Pin Functions for QFN package. 9 Clarified leakage current characteristics in High Temperature Considerations. 23 Added new Typical Applications. 30 8495fa Information furnished by Linear Technology Corporation is believed to be accurate and reliable. However, no responsibility is assumed for its use. Linear Technology Corporation makes no representation that the interconnection of its circuits as described herein will not infringe on existing patent rights. For more information www.linear.com/LT8495 33 LT8495 TYPICAL APPLICATIONS 450kHz, Wide Input Range 12V Output SEPIC Converter L1 10H VIN 3V TO 55V (VOUT RIPPLE MAY INCREASE BELOW 6V VIN) * C3 2.2F C1 2.2F VOUT 12V 0.2A (VIN = 3V) 0.35A (VIN = 4.5V) 0.65A (VIN = 12V OR HIGHER) D1 * 1M L2 10H SW C2 10F x3 BIAS RSTIN FB VIN SWEN 3.09k 110k GND CPOR LT8495 CWDT 4.7nF SS 1nF RT 1F 169k WDO WDE RST C WDI 8495 TA06 C1, C3: 2.2F, 100V, X5R, 1210 C2: 10F, 25V, X5R, 1210 D1: ONSEMI MBRA2H100 L1, L2: COILTRONICS DRQ125-100-R No Load Supply Current Efficiency 100 90 EFFICIENCY (%) SUPPLY CURRENT (A) 60 40 WATCHDOG ENABLED 20 0 10 20 30 40 INPUT VOLTAGE (V) 50 VIN = 24V 80 75 70 65 WATCHDOG DISABLED 0 VIN = 12V VIN = 5V 85 80 60 0.0 60 8495 TA06C 0.1 0.2 0.3 0.4 LOAD CURRENT (A) 0.5 0.6 8495 TA06b RELATED PARTS PART NUMBER DESCRIPTION COMMENTS LT8494 70V, 2A Boost/SEPIC 1.5MHz High Efficiency DC/DC Converter VIN(MIN) = 2.5V, VIN(MAX) = 32V, VOUT(MIN) = 70V, IQ = 9A, ISD = <1A, 4mm x 4mm QFN-20, TSSOP-20E Packages LT3580 42V, 2A Boost/Inverting 2.5MHz High Efficiency DC/DC Converter VIN: 2.5V to 32V, VOUT(MAX) = 40V, IQ = 1mA, ISD < 1A, 3mm x 3mm DFN-8, MSOP-8E Packages LT8580 65V, 1A Boost/Inverting DC/DC Converter VIN: 2.55V to 40V, VOUT(MAX) = 60V, IQ = 1.2mA, ISD < 1A, 3mm x 3mm DFN-8, MSOP-8E Packages LT8570/LT8570-1 65V, 500mA/250mA Boost/Inverting DC/DC Converter VIN(MIN) = 2.55V, VIN(MAX) = 40V, VOUT(MIN) = 60V, IQ = 1.2mA, ISD = <1A, 3 x 3 DFN-8, MSOP-8E Package LT8582 40V, Dual 3A, 2.5MHz High Efficiency Boost Converter VIN: 2.5V to 40V, VOUT(MAX) = 40V, IQ = 2.8A, ISD < 1A, 7mm x 4mm DFN-24 Package LT8471 40V, Dual 3A, Multitopology High Efficiency DC/DC Converter VIN: 2.6V to 50V, VOUT(MAX) = 45V, IQ = 2.4mA, ISD < 1A, TSOP-20E Package LT3581 40V, 3.3A, 2.5MHz High Efficiency Boost Converter VIN: 2.5V to 40V, VOUT(MAX) = 40V, IQ = 1mA, ISD < 1A, 4mm x 3mm DFN-14, MSOP-16E Packages LT8582 40V, Dual 3A Boost, Inverter, SEPIC, 2.5MHz High Efficiency Boost Converter VIN: 2.5V to 40V, VOUT(MAX) = 40V, IQ = 2.1mA, ISD < 1A, 7mm x 4mm DFN-24 Package LT3579/LT3579-1 40V, 3.3A Boost, Inverter, SEPIC, 2.5MHz High Efficiency Boost Converter VIN: 2.5V to 40V, VOUT(MAX) = 40V, IQ = 1mA, ISD < 1A, 4mm x 5mm QFN-20, TSSOP-20E Packages 8495fa 34 Linear Technology Corporation 1630 McCarthy Blvd., Milpitas, CA 95035-7417 For more information www.linear.com/LT8495 (408) 432-1900 FAX: (408) 434-0507 www.linear.com/LT8495 LT 0715 REV A * PRINTED IN USA LINEAR TECHNOLOGY CORPORATION 2015