Copyright © 2018 Active-Semi, Inc.
PAC5532EVK1 Users Guide
Power Application Controllers
www.active-semi.com
- 2 - Rev 1.0 February 2018
C
ONTENTS
Contents ...............................................................................................................................................................2
Overview ..............................................................................................................................................................3
PAC5532EVK1 Resources ..................................................................................................................................5
Pinout and Signal Connectivity .........................................................................................................................5
Power Input ......................................................................................................................................................6
LED’s ................................................................................................................................................................6
SWD Debugging ...............................................................................................................................................7
JTAG Debugging ..............................................................................................................................................7
Serial Communications .....................................................................................................................................7
Alternate Serial Communications .....................................................................................................................8
Hall Sensor / DAC Interface .............................................................................................................................8
PAC5532EVK1 Setup ....................................................................................................................................... 10
Power Considerations ....................................................................................................................................... 11
Maximum Current and Voltage ...................................................................................................................... 11
SENSE Resistors .......................................................................................................................................... 11
Power FETs ................................................................................................................................................... 11
Increasing Output Power (Appendix) ................................................................................................................ 12
Suggested Heat Sink Profile.......................................................................................................................... 12
Clamping Mechanisms .................................................................................................................................. 13
Adding DRS Clamps .................................................................................................................................. 13
About Active-Semi ® ......................................................................................................................................... 14
- 3 - Rev 1.0 February 2018
O
VERVIEW
Active-Semi’s PAC5532EVK1 development platform is a complete hardware solution enabling users not only
to evaluate the PAC5532 device, but also develop power applications revolving around this powerful and
versatile ARM
®
Cortex
®
-M4F based microcontroller. The module contains a PAC5532 Power Application
Controller
®
(MCU) and all the necessary circuitry to properly energize the MCU and its internal peripherals
once power is applied.
To aid in the application development, the PAC5532EVK1 offers access to each and every one of the
PAC5532 device’s signals by means of a series of male header connectors.
The PAC5532EVK1 also contains access to an external USB to UART module enabling users to connect the
evaluation module to a PC computer through a conventional Virtual Comm Port which can then be used in the
communication efforts by taking advantage of the PAC5532’s UART interface. Graphical User Interface (GUI)
software suites can be employed to externally control particular application features.
Finally, the PAC5532EVK1 module gives access to the PAC5532’s SWD and JTAG ports allowing users to
both program the application into the device’s FLASH memory, as well as debug the application in real time.
The provided 4 pin connector is compatible with a decent variety of SWD based debugger/programmer
modules, widely available. In parallel, a MIPI20 connector is made available that provides SWD, JTAG and
TRACE functionality, greatly expanding the existent debugging capabilities.
Active-Semi’s PAC5532EVK1 evaluation kit consists of the following:
PAC5532EVK1 evaluation module
PAC5532EVK1 User’s Guide
Schematics, BOM and Layout Drawings
- 4 - Rev 1.0 February 2018
Figure 1: PAC5532EVK1 Block Diagram
Solution Benefits:
Ideal for high voltage (up to 160V Abs Max) general purpose power applications and controllers
Single-IC PAC5532 with configurable PWM outputs, ADC inputs, I2C, UART, SPI communication
ports and GPIO.
Gate driving for up to three half H Bridge (tri phase) inverter.
Schematics, BOM, Layout drawings available
The following sections provide information about the hardware features of Active-Semi’s PAC5532EVK1
turnkey solution.
- 5 - Rev 1.0 February 2018
PAC5532EVK1
R
ESOURCES
Pinout and Signal Connectivity
The following diagram shows the male header pinout for the PAC5532EVK1 evaluation module, as seen from
above:
Figure 2 PAC5532EVK1 Headers and Test Stakes Pinout
- 6 - Rev 1.0 February 2018
Power Input
Power to the PAC5532EVK1 evaluation module can be applied to the VIN and GND spade connectors. Said
applied power should not exceed 160V (Abs Max).
The PAC5532EVK1 is optimized to operate with voltages ranging from 25V to 120V Nominal (160V Abs Max).
When the VIN input voltage goes above 25V, the system exits UVLO protection and all subsystems, including
voltage regulators, analog front end and microcontroller, are enabled.
LED’s
When an operational voltage is applied, LED D5 will light up. This is the LED which notifies that the VSYS
(5V) rail is up and running. VP (12V gate drive), 3.3V (for analog circuitry) and 1.2V (for CPU core) regulators
will also be operating at this point in time. The module is now ready for use.
The following table shows the available LEDs and their associated diagnostic function.
LED
Description
D
5
VSYS (5V). Lights up when the PAC5532 device is successfully powered up by VIN.
D
1
7
VIN. Lights up when VIN voltage is applied.
- 7 - Rev 1.0 February 2018
SWD Debugging
Connector J3 offers access to the PAC5532 SWD port lines.
JTAG Debugging
Connector J13 is a standard MIPI20 offering access to the JTAG port as well as single data line TRACE
debug.
J1
3
Pins
Terminal
Description
1
VCC VCC Power
2
SWDIO/TMS Serial Wire Debug Data Input Output / JTAG Test Mode Select
3
GND GND (System GND)
4
SWCLK/TCK Serial Wire Debug Clock / JTAG Clock
5
GND GND (System GND)
6
SWO/TDO Serial Wire Debug Output / JTAG Data Output
7
NC Not Connected
8
TDI JTAG Data Input
9
GND GND (System GND)
10
NC Not Connected
11
GND GND (System GND)
12
TRACE CLK ETM Trace Clock
13
GND GND (System GND)
14
TRACE DATA 0 ETM Trace Data 0
15
GND GND (System GND)
16
TRACE DATA 1 ETM Trace Data 1
17
GND GND (System GND)
18
TRACE DATA 2 ETM Trace Data 2
19
GND GND (System GND)
20
TRACE DATA 3 ETM Trace Data 3
Serial Communications
Connector J4 offers access to the PAC5532 UART port lines.
J
4
Pin
Terminal
Description
1
+ VCCIO (default is 3.3V)
2
TX MCU Transmit Line (PE3)
3
RX MCU Receive Line (PE2)
4
- GND (System Ground)
J
3
Pin
Terminal
Description
1
+ VCCIO (default is 3.3V)
2
SD SWD Serial Data
3
CL SWD Serial Clock
4
- GND (System Ground)
- 8 - Rev 1.0 February 2018
Alternate Serial Communications
When enabled, connector J14 provides access to a secondary UART port lines.
J
14
Pin
Terminal
Description
1
+ VCCIO (default is 3.3V)
2
TX MCU Transmit Line (PF3 – requires 0 ohm resistor R41 to be populated)
3
RX MCU Receive Line (PF2)
4
- GND (System Ground)
Hall Sensor / DAC Interface
Connector J12 offers access to the PAC5532 resources on PORTD utilized for hall sensor based
commutation. These resources can be alternatively utilized as PWM DAC outputs for in real time debugging.
Jumpers JMP1/2/3 are used to select the preferred function.
NOTE: 2 pin shunts must be placed on the JMP1/2/3 in order for the respective PORTD resources to be
made available.
Figure 3 DAC / Hall Sensor Jumper Selection
Jumper J
MP1
/
2
/
3
Description
1:2
Hall Sensor Functionality
2:3
DAC Functionality
NOTE: J12 functionality is only available when jumpers JMP1/2/3 have been shunted on the Hall Sensor
respective position.
J
1
2
Pin
Terminal
Description
1
+ VCCIO (default is 3.3V)
2
Hall Sensor U PORTD0
3
Hall Sensor V PORTD1
4
Hall Sensor W PORTD2
5
GND GND (System Ground)
- 9 - Rev 1.0 February 2018
NOTE: Test stakes DAC1/2/3 are only available when jumpers JMP1/2/3 have been shunted on the DAC
respective position
Test Stake
Description
DAC 1
PORTD0
DAC 2
PORTD1
DAC 3
PORTD2
- 10 - Rev 1.0 February 2018
PAC5532EVK1
S
ETUP
The setup for the PAC5532EVK1 evaluation module requires up to four simple connections.
1. Connect the VIN power source via spade tab connectors VIN and GND. As VIN power is applied, the
LED D17 will light up. Once VIN voltage goes above 25V, the PAC5532’s Multi Mode Power Manager
will be engaged and the VSYS (5V) regulator will be enabled. This event will result in LED D5 lighting
up.
2. Connect the 3 Phase BLDC/PMSM motor via spade tab connectors PHASE U, PHASE V and PHASE
W.
3. If Serial Communications are desired, connect the USB to UART module 4 pin connection to J4.
4. For debugging/programming, connect a suitable USB SWD module to J3 by using a standard 4 wire
cable.
Figure 4: PAC5532EVK1 Evaluation Module Connections
- 11 - Rev 1.0 February 2018
P
OWER
C
ONSIDERATIONS
Maximum Current and Voltage
The PAC5532EVK1 evaluation module was designed to operate with voltages in the 80V to 120V range.
Transients can go to as high as 160V (Abs Max).
The recommended operating current is 10A RMS per phase. Higher currents could be achieved, albeit the
user is responsible for applying different techniques to handle the increased thermal dissipation needs.
Please see the “Increasing Output Power” section for more information on how to achieve higher current
loading.
SENSE Resistors
The SENSE resistors utilized to digitize motor winding current will determine how much current the three
phase inverter will be able to handle. The PAC5532EVK1 module ships with 0.01 Ohm 3W SENSE resistors.
For higher current handling, a smaller SENSE resistor could be employed.
The equation utilized to compute maximum tri phase inverter leg current is:

=


Users are encouraged to modify SENSE resistor value according to their application. The following table
showcases different resistance values, maximum currents and suggested part numbers.
NOTE: For increased current handling, adding thermal heat sinking to the power FETs must be considered.
Power FETs
The PAC5532EVK1 ships with six IRFB4227PBF TO-220 Power FETs. These power switches are rated at
200V and 130A. RDSON is about 0.020 Ohms. In order to obtain the maximum performance out of these
components, some form of heat sinking is required. The evaluation module ships without a heat radiation
device. The appendix offers guidelines the measurements users can employ to fabricate their own version of
a simple metal heat plate.
Users are also encouraged to modify the evaluation module by exchanging power switches with other
components offering better thermal performance. Power FETs designed with a lower RDSON would tend to
require less heat sinking. Traditionally, such FETs would have a lower maximum voltage, but for applications
requiring smaller voltages, this may be an acceptable option.
Resistance (
)
Rat
ed Power (W)
Maximum RMS Current (A)
Part Number
0.01
3 17.3 CRA2512-FZ-R010ELF
0.002
5 50 CSS2H-2512K-2L00F
- 12 - Rev 1.0 February 2018
I
NCREASING
O
UTPUT
P
OWER
(A
PPENDIX
)
In this section we provide different techniques which must be employed when wanting to drive higher then
10A per phase loads. As depicted in previous sections, the user will be responsible for selecting a proper
SENSE resistor, suitable power FET, adding heat sinking and in some cases, some extra clamping.
Suggested Heat Sink Profile
The following drawing offers guidelines for a shape which could be utilized to fabricate a heat radiator. This
heat sinking metal plate is intended to be bolted onto the power FETs through the usage of gap pads and
insulating washers.
- 13 - Rev 1.0 February 2018
Clamping Mechanisms
When current load increases, destructive voltage transients can be observed. These transients are usually
prevalent during dead time, when current must find an asynchronous path (e.g. FET body diodes) to continue
its flow. Controlling these transients is of utmost importance to protect both the power switches as well as the
PAC5532 pre drive power stage block.
Adding DRS Clamps
The PAC5532EVK1 evaluation module already incorporates a series of clamps put in place to protect the
DRSx terminal from negative transients at the phase outputs. However, under high current scenarios, it is
plausible to see large positive transients. It is recommended to place a similar diode from DRS to VM in order
to clamp the PHASE output to VM.
- 14 - Rev 1.0 February 2018
A
BOUT
A
CTIVE
-S
EMI
®
Founded in 2004 in Silicon Valley and headquartered in Allen, Texas, Active-Semi® is a rapidly
emerging leader in the multi-billion dollar power management IC and intelligent digital motor drive IC
markets. The company's portfolio of analog and mixed signal SoCs (systems-on-chips) are scalable core
platforms used in charging, powering and embedded digital control systems for end applications such as
industrial, commercial and consumer equipment. The company offers power application
microcontrollers, DC/DC, AC/DC, PMU and LED drivers that significantly reduce solution size and cost
while improving system-level reliability. Active-Semi's turnkey solutions deliver energy-saving power
conversion architectures that minimize energy usage and compress system development cycle-time by
greater than 50 percent. Active-Semi ships 50 million power ICs per quarter and reached the "one billion
units shipped" milestone in May 2012. The multi-national company focuses on commercializing industry
leading power management IC solution platforms and has developed broad intellectual property with
over 150 patents granted and pending. For more information visit: http://active-semi.com/
LEGAL INFORMATION & DISCLAIMER
Copyright © 2018 Active-Semi, Inc. All rights reserved.
All information provided in this document is subject to legal disclaimers.
Active-Semi reserves the right to modify its products, circuitry or product specifications without notice. Active-Semi products are not intended, designed, warranted
or authorized for use as critical components in life-support, life-critical or safety-critical devices, systems, or equipment, nor in applications where failure or
malfunction of any Active-Semi product can reasonably be expected to result in personal injury, death or severe property or environmental damage. Active-Semi
accepts no liability for inclusion and/or use of its products in such equipment or applications. Active-Semi does not assume any liability arising out of the use of any
product, circuit, or any information described in this document. No license, express, implied or otherwise, is granted under any patents, copyrights or other
intellectual property rights of Active-Semi or others. Active-Semi assumes no liability for any infringement of the intellectual property rights or other rights of third
parties which would result from the use of information contained herein. Customers should evaluate each product to make sure that it is suitable for their
applications. Customers are responsible for the design, testing, and operation of their applications and products using Active-Semi products. Customers should
provide appropriate design and operating safeguards to minimize the risks associated with their applications and products. All products are sold subject to Active-
Semi's terms and conditions of sale supplied at the time of order acknowledgment. Exportation of any Active-Semi product may be subject to export control laws.
Active-Semi®, Power Application Controller® and PAC® are registered trademarks of Active-Semi, Inc. Solutions for SustainabilityTM, Micro Application
ControllerTM, Multi-Mode Power ManagerTM, Configurable Analog Front EndTM, and Application Specific Power DriversTM are trademarks of Active-Semi, Inc.
ARM® and Cortex are registered trademarks of ARM Limited. All referenced brands and trademarks are the property of their respective owners.