PRELIMINARY CY28158 Spread Spectrum Timing Solution for Serverworks Chipset Features Key Specifications * Maximized EMI suppression using Cypress's spread spectrum technology Supply Voltages: ......................................VDD33 = 3.3V 5% .................................................................VDD25 = 2.5V 5% * Based on Industry Standard CK133 Pinout with all outputs compliant to CK98 specifications CPU Output Jitter: ................................................... .<150 ps * 0.5% downspread outputs deliver up to 10dB lower EMI CPU to 3V66 Output Offset: 0.0 to1.5 ns * 6 skew-controlled copies of CPU output CPU to IOAPIC Output Offset 1.5 to 4.0 ns (CPU leads) * 6 copies of PCI output (synchronous w/CPU output) CPU to PCI Output Offset ................. 0 to 4.0 ns (CPU leads) CPU Output Skew:.................................................... <175 ps (CPU leads) * 2 copies of 66 MHz fixed frequency 3.3V clock * 3 copies of 16.67 MHz IOAPIC clock, synchronous to CPU clock Table 1. Pin Selectable Frequency SEL133/100# CPU0:5 (MHz) PCI * 1 copy of 48 MHz USB output 1 133 33.3 * 2 copies of 14.31818 MHz reference clock 0 100 33.3 * Programmable to 133 or 100 MHz operation * Power management control pins for clock stop and shut down * Available in 56-pin SSOP Block Diagram X1 X2 Pin Configuration 2 XTAL OSC REF0:1 CPU_STOP# 6 STOP Clock Logic 2 CPU0:5 PLL 1 SEL133/100# /2//1.5 3V66_0:1 1 PCI_F /2 PWRDWN# STOP Clock Logic 5 PCI1:5 PCI_STOP# Power Down Logic 3 /2 IOAPIC0:2 Tristate Logic PLL2 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 56 55 54 53 52 51 50 49 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 VDD_IOAPIC IOAPIC2 IOAPIC1 IOAPIC0 GND_IOAPIC VDD_CPU CPU5 CPU4 GND_CPU VDD_CPU CPU3 CPU2 GND_CPU VDD_CPU CPU1 CPU0 GND_CPU VDDA GNDA PCI_STOP# CPU_STOP# PWR_DWN# SPREAD# SEL1 SEL0 VDD_48MHZ 48MHZ GND_48MHZ 1 48MHz Rev 1.0, November 20, 2006 2200 Laurelwood Road, Santa Clara, CA 95054 CY28158 SPREAD# SEL0 SEL1 STOP Clock Logic GND_REF REF0 REF1 VDD_REF X1 X2 GND_PCI GND_PCI PCI_F VDD_PCI PCI1 PCI2 GND_PCI PCI3 PCI4 VDD_PCI VDD_PCI PCI5 GND_PCI GND_3V66 GND_3V66 VDD_3V66 VDD_3V66 GND_3V66 3V66_0 3V66_1 VDD_3V66 SEL133/100# Page 1 of 9 Tel:(408) 855-0555 Fax:(408) 855-0550 www.SpectraLinear.com CY28158 Pin Definitions Name Pins Description [1] X1 5 Reference crystal input X2[1] 6 Reference crystal feedback CPU [0-5] 41, 42, 45, 46, 49, 50 CPU clock outputs PCI [1-5] 11, 12, 14, 15, 18 PCI clock outputs, synchronously running at 33.33 MHz PCI_F 9 Free running PCI clock 3V66 [0-1] 25, 26 3V66 clock outputs, running at 66.66 MHz IOAPIC [0-2] 53, 54, 55 IOAPIC clock outputs, running at 16.67 MHz REF [0-1] 2, 3 Reference clock outputs, 14.318 MHz 48MHZ 30 48-MHz USB clock output CPU_STOP# 36 Active LOW input, disables CPU and 3V66 clocks when asserted PCI_STOP# 37 Active LOW input, disables PCI clocks when asserted PWR_DWN# 35 Active LOW input, powers down part when asserted SPREAD# 34 Active LOW input, enables spread spectrum when asserted SEL1 33 CPU frequency select input (See Function Table) SEL0 32 CPU frequency select input (See Function Table) SEL133/100# 28 CPU frequency select input (See Function Table) GND_REF 1 3.3V Reference ground GND_PCI 7, 8, 13, 19 3.3V PCI ground GND_3V66 20, 21, 24 3.3V 66-MHz (AGP) ground GND_48MHZ 29 3.3V 48-MHz (USB) ground GND_IOAPIC 52 2.5V APIC ground GND_CPU 40, 44, 48 2.5V CPU ground GNDA 38 Analog ground to PLL and Core VDD_REF 4 3.3V Reference voltage supply VDD_PCI 10, 16, 17 3.3V PCI voltage supply VDD_3V66 22, 23, 27 3.3V 66-MHz (AGP) voltage supply VDD_48MHZ 31 3.3V 48-MHz (USB) voltage supply VDD_IOAPIC 56 2.5V APIC voltage supply VDD_CPU 43, 47, 51 2.5V CPU voltage supply VDDA 39 Analog voltage supply to PLL and Core Note: 1. For best accuracy, use a parallel-resonant crystal, CLOAD = 18 pF. For crystals with different CLOAD, please refer to the application note, "Crystal Oscillator Topics." Rev 1.0, November 20, 2006 Page 2 of 9 CY28158 Function Table[2] SEL133/ 100# SEL1 CPU (MHz) SEL0 3V66 (MHz) PCI (MHz) 48MHZ (MHz) REF (MHz) IOAPIC (MHz) 0 0 0 Hi-Z Hi-Z Hi-Z Hi-Z Hi-Z Hi-Z 0 0 1 100.227[3] 66.818[3] 33.409[3] 48.008[3] 14.318[3] 16.705[3] 0 1 0 100 66.67 33.33 OFF 14.318 16.67 0 1 1 100 66.67 33.33 48.008[3] 14.318 16.67 1 0 0 TCLK/2 TCLK/4 TCLK/8 TCLK/2 TCLK TCLK/16 1 0 1 N/A N/A N/A N/A N/A N/A 1 1 0 133.33 66.67 33.33 OFF 14.318 16.67 1 1 1 133.33 66.67 33.33 48.008[3] 14.318 16.67 Actual Clock Frequency Values Target Frequency (MHz) Clock Output Actual Frequency (MHz) PPM CPU 100.0 99.126 -8740 CPU 133.33 132.769 -4208 48.0 48.008 167 48MHZ Clock Enable Configuration CPU_STOP# CPU 3V66 PCI PCI_F REF IOAPIC OSC. VCOs X LOW LOW LOW LOW LOW OFF OFF 0 LOW LOW LOW ON ON ON ON 1 1 LOW LOW ON ON ON ON ON 1 0 ON ON LOW ON ON ON ON 1 1 ON ON ON ON ON ON ON PWR_DWN# PCI_STOP# X 0 0 1 0 1 1 Clock Driver Impedances Impedance VDD Range Buffer Type Minimum : 2.375V - 2.625V Type 1 13.5 29 45 48MHZ, REF 3.135V - 3.465V Type 3 20 40 60 PCI, 3V66 3.135V - 3.465V Type 5 12 30 55 Buffer Name CPU, IOAPIC Typical : Maximum : Note: 2. TCLK is a test clock driven in on the X1 input in test mode. 3. This selection is defined as "N/A" or "Reserved." Rev 1.0, November 20, 2006 Page 3 of 9 CY28158 Maximum Ratings Storage Temperature (Non-Condensing) ....-65qC to +150qC (Above which the useful life may be impaired. For user guidelines, not tested.) Max. Soldering Temperature (10 sec) ....................... +260qC Junction Temperature................................................ +150qC Supply Voltage..................................................-0.5 to +7.0V Package Power Dissipation.............................................. 1W Input Voltage.............................................. -0.5V to VDD+0.5 Static Discharge Voltage (per MIL-STD-883, Method 3015) ............................. >2000V Operating Conditions[4] Over which Electrical Parameters are Guaranteed Parameter Description Min. Max. Unit 3.135 3.465 V VDD_REF, VDD_PCI, VDDA, VDD_3V66, VDD_48MHZ 3.3V Supply Voltages VDD_CPU CPU Supply Voltage 2.375 2.625 V VDD_IOAPIC IOAPIC Supply Voltage 2.375 2.625 V 0 70 TA Operating Temperature, Ambient CL Max. Capacitive Load on CPU, 48MHZ, REF, IOAPIC PCI, 3V66 f(REF) Reference Frequency, Oscillator Nominal Value qC pF 20 30 14.318 14.318 MHz Electrical Characteristics Over the Operating Range Parameter Description Test Conditions Min. Max. Unit VIH High-level Input Voltage Except Crystal Pads. Threshold voltage for crystal pads = VDD/2 2.0 VIL Low-level Input Voltage Except Crystal Pads VOH High-level Output Voltage CPU, IOAPIC VOL Low-level Output Voltage IIH Input High Current 0 < VIN < VDD IIL Input Low Current 0 < VIN < VDD IOH High-level Output Current CPU VOH = 2.0V -16 IOAPIC VOH = 2.0V -20 48 MHZ, REF VOH = 2.4V -15 3V66, PCI VOH = 2.4V -30 CPU VOL = 0.4V 19 IOAPIC VOL = 0.4V 25 48 MHZ, REF VOL = 0.4V 10 3V66, PCI VOL = 0.4V 20 V 0.8 IOH = -1 mA 2.0 48 MHZ, REF, PCI, 3V66 IOH = -1 mA 2.4 CPU, IOAPIC IOL = 1 mA 0.4 48 MHZ, REF, PCI, 3V66 IOL = 1 mA 0.4 V V 10 10 V PA PA mA -60 -72 -51 -100 IOL Low-level Output Current mA 49 58 24 49 IOZ Output Leakage Current Three-state 10 PA IDD2 2.5V Power Supply Current VDDA/VDD33 = 3.465V, VDD25 = 2.625V, FCPU = 133 MHz 90 mA Rev 1.0, November 20, 2006 Page 4 of 9 CY28158 Electrical Characteristics Over the Operating Range (continued) Parameter Description Test Conditions Min. Max. Unit IDD3 3.3V Power Supply Current VDDA/VDD33 = 3.465V, VDD25 = 2.625V, FCPU = 133 MHz 160 mA IDDPD2 2.5V Shutdown Current VDDA/VDD33 = 3.465V, VDD25 = 2.625V 100 PA IDDPD3 3.3V Shutdown Current VDDA/VDD33 = 3.465V, VDD25 = 2.625V 200 PA Switching Characteristics[5] Over the Operating Range Min. Max. Unit t1 Parameter All Output Output Duty Cycle[6] Description t1A/t1B Test Conditions 45 55 % t2 CPU, IOAPIC Rising Edge Rate Between 0.4V and 2.0V 1.0 4.0 V/ns t2 48MHZ, REF Rising Edge Rate Between 0.4V and 2.4V 0.5 2.0 V/ns t2 PCI, 3V66 Rising Edge Rate Between 0.4V and 2.4V 1.0 4.0 V/ns t3 CPU, IOAPIC Falling Edge Rate Between 2.0V and 0.4V 1.0 4.0 V/ns t3 48MHZ, REF Falling Edge Rate Between 2.4V and 0.4V 0.5 2.0 V/ns t3 PCI, 3V66 Falling Edge Rate Between 2.4V and 0.4V 1.0 4.0 V/ns t6 CPU CPU-CPU Skew Measured at 1.25V 175 ps t8 IOAPIC IOAPIC-IOAPIC Skew Measured at 1.25V 250 ps t9 3V66 3V66-3V66 Skew Measured at 1.5V 250 ps t10 PCI PCI-PCI Skew Measured at 1.5V 500 ps t11 CPU, 3V66 CPU-3V66 Clock Skew CPU leads. Measured at 1.25V for 2.5V clocks and 1.5V for 3.3V clocks 0 1.5 ns t12 3V66, PCI 3V66-PCI Clock Skew 3V66 leads. Measured at 1.5V 0.5 2.5 ns t13 CPU, IOAPIC CPU-IOAPIC Clock Skew CPU leads. Measured at 1.25V 1.5 4 ns CPU Cycle-Cycle Clock Jitter With all outputs running 150 ps IOAPIC Cycle-Cycle Clock Jitter 500 ps 48MHZ Cycle-Cycle Clock Jitter 500 ps 3V66 Cycle-Cycle Clock Jitter 500 ps REF Cycle-Cycle Clock Jitter CPU, PCI Settle Time CPU and PCI clock stabilization from power-up 1000 ps 3 ms Notes: 4. Multiple Supplies: The voltage on any input or I/O pin cannot exceed the power pin during power-up. Power supply sequencing is NOT required. 5. All parameters specified with loaded outputs. 6. Duty cycle is measured at 1.5V when VDD = 3.3V. When VDD = 2.5V, duty cycle is measured at 1.25V. Rev 1.0, November 20, 2006 Page 5 of 9 CY28158 Switching Waveforms Duty Cycle Timing t1A t1B All Outputs Rise/Fall Time VDD OUTPUT 0V t2 t3 CPU-CPU Clock Skew CPUCLK CPUCLK t6 IOAPIC-IOAPIC Clock Skew IOAPIC IOAPIC t8 3V66 - 3V66 Clock Skew 3V66 3V66 t9 Rev 1.0, November 20, 2006 Page 6 of 9 CY28158 Switching Waveforms (continued) PCI-PCI Clock Skew PCI PCI t10 CPU - 3V66 Clock Skew CPU 3V66 t11 3V66 - PCI Clock Skew 3V66 PCI t12 CPU-IOAPIC Clock Skew CPU t13 IOAPIC [7, 8] CPU_STOP# Timing CPU (Internal) PCI (Internal) PCI_F (Free-Running) CPU_STOP# CPU, 3V66 (External) Notes: 7. CPU on and CPU off latency is 2 or 3 CPU cycles. 8. CPU_STOP# may be applied asynchronously. It is synchronized internally. Rev 1.0, November 20, 2006 Page 7 of 9 CY28158 Switching Waveforms (continued) PCI_STOP# CPU (Internal) PCI (Internal) PCI_F (Free-Running) PCI_STOP# PCI (External) PWR_DWN# CPU (Internal) PCI (Internal) PWR_DWN# CPU (External) PCI (External) VCO Crystal Shaded section on the VCO and Crystal waveforms indicates that the VCO and crystal oscillator are active, and there is a valid clock. Test Circuit VDD_PCI, VDD_3V66, VDD_48MHZ, VDD_REF, VDDA 1, 7, 8, 13, 19, 20, 21, 24, 29, 40, 44, 48, 52 4, 10, 16, 17, 22, 23, 27, 31, 39 CY28158 VDD_CPU, VDD_IOAPIC OUTPUTS CLOAD 43, 47, 51, 56 Note: Each supply pin must have an individual decoupling capacitor on test circuit at 0.1 PF. Note: All capacitors must be placed as close to the pins as is physically possible. Ordering Information Ordering Code Package Name Package Type Operating Range CY28158PVC O56 56-Pin SSOP Commercial CY28158PVCT O56 56-Pin SSOP- Tape and Reel Commercial CY28158OXC O56 56-Pin SSOP Commercial CY28158OXCT O56 56-Pin SSOP- Tape and Reel Commercial Lead Free Rev 1.0, November 20, 2006 Page 8 of 9 CY28158 Package Diagram 56-Lead Shrunk Small Outline Package O56 51-85062-C While SLI has reviewed all information herein for accuracy and reliability, Spectra Linear Inc. assumes no responsibility for the use of any circuitry or for the infringement of any patents or other rights of third parties which would result from each use. This product is intended for use in normal commercial applications and is not warranted nor is it intended for use in life support, critical medical instruments, or any other application requiring extended temperature range, high reliability, or any other extraordinary environmental requirements unless pursuant to additional processing by Spectra Linear Inc., and expressed written agreement by Spectra Linear Inc. Spectra Linear Inc. reserves the right to change any circuitry or specification without notice. Rev 1.0, November 20, 2006 Page 9 of 9