Du line Output-Module for Elevators Type G 2130 55.1 700 (R) Fieldbus Installationbus * 8 NPN- or PNP-transistor outputs for control of floor-indicators * Open printed circuit board * Bracket for DIN-rail mounting available * LED-indications for supply and Dupline(R) carrier * 3-wire system with Dupline(R) and DC-supply through G 2196 0000 700 * Channel coding by GAP 1605 Product Description Ordering Key in an elevator is connected to the same 3 wires for buscommunication with the control system and DC-powersupply for the lamps/LED's. Installer friendly mounting, operation and maintenance without requirement of any special tools or programming. Type: Dupline(R) Open PCB Output-Module Number of I/Os Output type DC-supply Supply Ordering no. NPN-outputs Ordering no. PNP-outputs 10-30 VDC G 2130 5511 700 G 2130 5521 700 Module with 8 NPN- or PNPtransistor outputs for direct interface to elevator floor indicators. The 8 outputs can either be connected to the 8 inputs of intelligent floor indicators which are controlled by bit-combinations or they can be used to drive LEDsegments directly. All modules G 2130 5521 700 Type Selection Output Specifications General Specifications Outputs Output voltage drop Current per output Total load capability (01..08) Reverse polarity protection Short-circuit protection Built-in protective diodes Off-state leakage current Response time Power ON delay Indication for Supply ON Dupline(R) carrier Environment Operating temperature Storage temperature Humidity (non-condensing) Mechanical resistance Shock Vibration Dimensions 8 PNP-transistors 2.0 V 100 mA 500 mA Yes None Yes 200 A 1 pulse train (136 ms @ 128 channels) Supply Specifications Power supply Rated operational voltage (Vin) Ripple Reverse polarity protection Current consumption Power dissipation Inrush current Transient protection voltage Dielectric voltage Supply - Dupline(R) Supply - Outputs Overvoltage cat. III (IEC 60664) 10-30 VDC (ripple included) 3V Yes 45 mA 1W 1A 800 V Weight Typ. 2 s LED, green LED, yellow -20 to +50C (-4 to +122F) -50 to +85C (-58 to +185F) 20 - 80% 15 G (11 ms) 2 G (6 to 55 Hz) Open PCB 74 x 59 mm 4 pcs. of nylon PA6 snap locks are included for mounting the PCB in o 4.8 holes 50 g None None Specifications are subject to change without notice (29.04.03) Dupline(R) is a registered trademark. A product of the CARLO GAVAZZI Group 1 Du line G 2130 55.1 700 (R) Fieldbus Installationbus Dup (Dupline(R) S) GND Channel program plug Dup (Dupline(R) S) GND POW (Supply input) POW (Supply input) DC + DC + O1 O1 G 21305521... G 21305511... Channel program plug Wiring Diagrams O2 O3 O4 O2 O3 O4 O7 O6 LIne Supply O5 O6 LIne Supply O5 O7 O8 O8 Pin Allocation Mode of Operation Terminal Input/Output DUP GND POW DC + O1 O2 O3 O4 O5 O6 O7 O8 Dupline(R) signal Dupline(R) + supply GND Supply IN DC for output loads Output 1 Output 2 Output 3 Output 4 Output 5 Output 6 Output 7 Output 8 Accessories Aluminium bracket for DIN-mounting DIN-rail 2 8047- bracket FMD 411 The output unit uses three wires for the communication with all the other I/O-units of an installation, for the supply of the I/O-units and for the loads connected to the outputs of the units. This implies, that the "common" of the communication signal is identical to the "minus" of the supply. The DC supply voltage must connect to the system through a G 2196 0000 700, which also performs the channel generator function and the RS485 communication link to the elevator controller (please refer to the data sheet for G2196 0000 700 for details). 8 out of the 128 available Dupline(R) adresses should be reserved to control the floorindicators. Since all the indicators must show the same value, the output modules can all be coded to read the same adresses. This implies that only 8 adresses will be occupied for floor indication no matter how many indicators are installed. The output status of all outputs of an output unit may be predefined for cases like loss of power and loss of communication. Please refer to the paragraph "Output status setting" of the data sheet for the GAP 1605 to change the default setting (all outputs OFF). Specifications are subject to change without notice (28.09.99) Dupline(R) is a registered trademark. A product of the CARLO GAVAZZI Group