ASDHS-MLC C2 Series Half-Slim (JEDEC MO-297) SATA 6 Gb/s Solid State Drive Specification Manual Rev.: Revision Date: Part Number: 1.00 June 4, 2012 50-1Z129-1000 Advance Technologies; Automate the World. Document History 2 Revision Date 1.00 2012/06/04 Changes Initial Release Specification Copyright 2012 ADLINK Technology, Inc. Disclaimer The information in this document is subject to change without prior notice in order to improve reliability, design, and function and does not represent a commitment on the part of the manufacturer. In no event will the manufacturer be liable for direct, indirect, special, incidental, or consequential damages arising out of the use or inability to use the product or documentation, even if advised of the possibility of such damages. This document contains proprietary information protected by copyright. All rights are reserved. No part of this datasheet may be reproduced by any mechanical, electronic, or other means in any form without prior written permission of ADLINK Technology, Inc. Specification 3 Table of Contents 4 1 Introduction .........................................................................5 1.1 1.2 1.3 1.4 1.5 1.6 1.7 Overview................................................................................................. 5 Product Specification................................................................................... 5 Functional Block Diagram ............................................................................10 Product Images ........................................................................................10 Mechanical Drawing: Compatible with JEDEC MO-297 ( w/o case ) ...........................11 Architecture ............................................................................................12 Hot Plug Support ......................................................................................12 2 Pin Locations and Signal Descriptions .................................13 2.1 2.2 Pin Locations...........................................................................................13 Signal Descriptions....................................................................................13 3 ATA Command Sets ............................................................15 3.1 3.2 3.3 3.4 3.5 3.6 3.7 3.8 ATA Command ........................................................................................15 Power Management Command Set.................................................................19 Security Mode Feature Set...........................................................................19 SMART Command Set ...............................................................................19 Host Protected Area Command Set.................................................................20 48-Bit Address Command Set .......................................................................21 Device Configuration Overlay Command Set ......................................................21 General Purpose log Command Set ................................................................21 4 SATA Command Sets...........................................................22 4.1 SATA Command.......................................................................................22 5 References..........................................................................23 6 Getting Service ...................................................................24 Specification 1 Introduction 1.1 Overview The ASDHS-MLC64G Half-Slim SATA 6 Gb/s MLC Solid State Drive (SSD) delivers leading performance a JEDEC MO-297 Half-Slim form factor while simultaneously improving system responsiveness for mobile applications over standard rotating drive media or hard disk drives. By combining leading NAND flash memory technology with our innovative high performance firmware, ADLINK delivers a SSD for native Serial Advanced Technology Attachment (SATA) hard disk drive drop-in replacement with enhanced performance, reliability, ruggedness and power savings, since there are no rotating platters, moving heads, fragile actuators, or unnecessary delays due to spin-up time or positional seek time that can slow down the storage subsystem significantly I/O and throughput performance improvement as compared to rotating media or hard disk drives. This document describes the specifications of the ASDHS-MLC64G Half-Slim SATA 6 Gb/s MLC SSD in Half-Slim (JEDEC MO-297) form factor. The ASDHS-MLC64G Half-Slim SATA 6 Gb/s MLC SSD primarily targets SATA based laptop PCs, highly rugged mobile client devices, as well as thin and light, mini/sub-notebooks. Key attributes include high performance, low power, increased system responsiveness, high reliability, and enhanced ruggedness as compared to standard mobile SATA hard drives. The ASDHS-MLC64G Half-Slim SATA 6 Gb/s MLC SSD is available in 2.5" and Half-Slim form factors that are electrically, mechanically, and software compatible with existing 2.5" Serial ATA slots and cables. Our flexible design allows interchangeability with existing mobile hard drive based on the SATA interface standard. 1.2 Product Specification 1.2.1. Form Factor: Available in 2.5" and Half-Slim (JEDEC MO-297) SSD form factor 1.2.2. Capacity: 64GB (ASDHS-MLC64G-C2 ) Unformatted capacity 64GB Total user addressable sectors in LBA mode 125,045,424 Table 1: User Addressable Sectors Notes: 1. 1GB=1,000,000,000 bytes and not all of the memory can be used for storage. 2. 1 Sector = 512 bytes 1.2.3. Flash: Multi-Level Cell (MLC) component with Toggle-Mode (24nm ) Specification 5 1.2.4. Bandwidth Performance (CrystalDiskMark) Access Type MB/s Sequential Read Sequential Write Up to 350 (SATA 6 Gb/s, Secondary) Up to 170 (SATA 6 Gb/s, Secondary) Table 2: Maximum Sustained Read and Write Bandwidth Notes: 1). Performance measured using CrystalDiskMark. 2). 1 MB/sec = 1,048,576 bytes/sec is used in measuring sequential performance. If 1 MB/sec = 1,000,000 bytes/sec is used, performance values become 4.85% higher. 1.2.5. Read and Write IOPS (IOMETER) Access Type IOPS 4K Read (IOPS) 4K Write (IOPS) 48,000 (SATA 6 Gb/s, Secondary) 38,000 (SATA 6 Gb/s, Secondary) Table 3: Random Read/Write Input/Output Operations per Second Notes: 1. Performance measured using IOMETER Pro with queue depth set to 32 2. Write cache enabled 3. Test computer: Dell E6400 (SATA 3 Gb/s - Win7 x64) and Sandy Bridge (SATA 6 Gb/s - Win7 x64) 1.2.6. Power on to ready: Type Average Latency Power on to Ready 1s Table 4: Latency Specifications Notes: 1. Write cache enabled 2. Device measured using Drive Master 3. Power on to ready time assumes proper shutdown (Power removal preceded by STANDBY command) 6 Specification 1.2.7. Compatibility -- SATA Revision 3.0 compliant Compatible with SATA 1.5Gb/s, 3Gb/s & 6Gb/s interface rates -- ATA/ATAPI- 8 compliant -- SSD enhanced SMART ATA feature set -- Native Command Queuing (NCQ) command set -- TRIM supported 1.2.8. Certifications Certification CE compliant UL certified BSMI Description Indicates conformity with the essential health and safety requirements set out in European Directives Low voltage Directive and EMC Directive Underwriters Laboratories, Inc. Component Recognition UL60950-1 Compliance to the Taiwan EMC standard "Limits and methods of Radio Disturbance Characteristics of Information Technology Equipment, CNS 13438 Class B" Microsoft WHQL Microsoft Windows Hardware Quality Labs RoHS compliant Restriction of Hazardous Substance Directive Table 6: Device Certifications 1.2.9. Power Management -- 5V SATA -- SATA interface power management -- OS-aware hot plug/removal 1.2.10. Power consumption Description Operating voltage for 5V (+/- 5%) Min 4.75 Max 5.25 Unit V Table 7: Operating Voltage Mode Active (average) Type 2.8 Unit W Idle (average) 0.7 W Table 8: Typical Power Consumption Note: Active power is measured using IOMETER Power Consumption using Data Logger _No DIPM Specification 7 1.2.11. Temperature Environment Ambient Temperature Humidity Mode Operating Min 0 Non-operating Type Max 70 Unit C -40 85 C Operation 5 95 % Non-operation 5 95 % Table 9: Temperature Relative Specifications Note: Measured without condensation 1.2.12. Reliability Parameter Mean Time between Failure (MTBF) Value 1,500,000 hours Power on/off cycles 50000 cycles Table 10: Reliability Specifications 1.2.14. Shock and Vibration: Item Shock1 Vibration2 Mode Non-operating Timing/Frequency At 1 msec Max 1500G Non-operating At 2 msec 1000G Operation 7~800 Hz 2.17Grms Non-operation 7~800 Hz 3.08Grms Table11: Shock and Vibration Notes: 1. Shock specifications assume that the SSD is mounted securely with the input vibration applied to the drive mounting screws. Stimulus may be applied in the X, Y or Z axis 2. Vibration specifications assume that the SSD is mounted securely with the input vibration applied to the drive mounting screws. Stimulus may be applied in the X, Y or Z axis. The measured specification is in root mean squared form. 8 Specification 1.2.15. Electromagnetic Immunity Electromagnetic Immunity tests assume the SSD is properly installed in the representative host system. The drive operates properly without errors degradation in performance when subjected to radio frequency (RF) environments defined in the following table. Test Description Electrostatic discharge Electrostatic discharge Electrostatic discharge Radiated RF immunity Electrical fast transient Contact 4KV Air: 8KV Contact 6KV Air: 12KV Contact 8KV Air: 15KV 80~1000MHz, 3V/m, 80% AM with 1 KHz sine 900 MHz, 3 V/m, 50% pulse modulation at 200Hz 1KV on AC mains 0.5KV on external I/O 1KV differential 2KV common, AC mains 150KHz~80 MHz, 3 Vrms, Conducted RF immunity 80% AM with 1KHz sine Power frequency 50Hz, 1A/m (r.m.s) magnetic filed Surge immunity Performance criteria Reference standard A IEC 61000-4-2:2008 B IEC 61000-4-2:2008 C IEC 61000-4-2:2008 A IEC 61000-4-3:2008 B IEC 61000-4-4:2004 +Corr.1:2006 +Corr.2:2007 B IEC 61000-4-5:2008 A IEC 61000-4-6:2008 A IEC 61000-4-6:2008 Table 12: Radio Frequency Specifications Notes: 1. Performance criterion A = The device shall continue to operate as intended, i.e., normal unit operation with no degradation of performance. 2. Performance criterion B = The device shall continue to operate as intended after completion of test, however, during the test, some degradation of performance is allowed as long as there is no data loss operator intervention to restore device function. 3. Performance criterion C = Temporary loss of function is allowed. Operator intervention is acceptable to restore device function. 4. Contact electrostatic discharge is applied to drive enclosure. 1.2.16. Weight: 10 g Max 1.2.17. Dimension: 39.0 x 54.0 x 4 mm (L x W x H) 1.2.18. Part Numbers: Product Name ASDHS-MLC64G-C2 Specification Part No. 92-99060-7010 9 1.3 Functional Block Diagram DDR3 DRAM SATA Host Interface 1.4 Flash Memory Controller NAND Flash Array Product Images 1.4.1. Half-Slim SATA SSD 10 Specification 1.5 Mechanical Drawing: Compatible with JEDEC MO-297 ( w/o case ) Dimensions in mm.: 39.0 x 54.0 x 4 mm (L x W x H) Specification 11 1.6 Architecture The ASDHS-MLC64G Half-Slim SATA 6 Gb/s Solid State Drive (SSD) utilizes a cost effective system-on-chip (SoC) design to manage a full SATA 6 Gb/s bandwidth with the host while managing multiple flash memory devices on multiple channels internally. 1.7 Hot Plug Support Hot Plug insertion and removal are supported when the correct connector and an appropriate operating system (OS) are used as described in the SATA 3.0 Specification. This product supports asynchronous signal recovery and will establish communications with a host system without hardware device detection by issuing an unsolicited COMINIT when first mated with a powered connector. 12 Specification 2 Pin Locations and Signal Descriptions 2.1 Pin Locations The data and power connector pin locations of the ASDHS-MLC64G Half-Slim SATA 6 Gb/s SSD are as shown below. 2.2 Signal Descriptions Data Connector: Name S1 Type GND S2 A+ S3 A- S4 GND S5 B- S6 B+ S7 GND Description Differential Signal Pair A Differential Signal Pair B Table 13: Serial ATA Data Connector Pin Definitions Specification 13 Power Connector: Name P1 Type V33 Description 3.3V Power P2 V33 3.3V Power P3 V33 3.3V Power, Pre-change P4 GND P5 GND P6 GND P7 V5 5V Power, Pre-change P8 V5 5V Power P9 V5 5V Power P10 GND P11 DAS/DSS P12 GND P13 V12 12V Power, Pre-change P14 V12 12V Power P15 V12 12V Power Device Activity Signal / Disable Staggered Spinup Table 14: Serial ATA Power Connector Pin Definitions Note: 1. All pins are in a signal row, with a 1.27mm (0.05") pitch 2. Pins P1, P2 and P3 are connected together, although they are not connected internally to the device. The host may put 3.3v on these pins. 3. The mating sequence is - The ground pins P4-P6, P10, P12 and the 5V power pin P7 - The signal pins and the rest of the 5V power pins P8-P9 4. Ground connectors P4 and P12 may contact before the other 1st mate pins in both the power and signal connectors to discharge ESD in a suitably configured backplane connector. 5. Power pins P7, P8 and P9 are internally connected to one another within the device. 6. The host may ground P11 if it is not used for Device Activity Signal (DAS) 7. Pins P13, P14, P15 are connected together, although they are not connected internally to the device. 14 Specification 3 ATA Command Sets 3.1 ATA Command The ASDHS-MLC64G Half-Slim SATA 6 Gb/s SSD supports all the mandatory ATA commands defined in the ATA/ATAPI-8 specification. 3.1.1. ATA General Feature Command Set The ASDHS-MLC64G Half-Slim SATA 6 Gb/s SSD supports the ATA General feature Command set (nonpacket), which consists of EXECUTE DEVICE DIAGNOSTIC FLUSH CACHE IDENTIFY DEVICE READ DMA READ SECTOR(S) READ VERIFY SECTORS(S) SEEK SET FEATURES WRITE DMA WRITE SECTOR(S) READ MULTIPLE SET MULTIPLE MODE WRITE MULTIPLE The ASDHS-MLC64G Half-Slim SATA 6 Gb/s SSD supports all the following optional commands READ BUFFER WRITE BUFFER NOP DOWNLOAD MICROCODE Specification 15 3.1.2. Identify Device Data The following table details the sector data returned after issuing an IDENTIFY DEVICE command. 16 Word F=Fixed V=Variable X=Both Default Value 0 F 0040h 1 2 3 4-5 X V X X 3FFFh C837h 0010h 0h 6 X 003Fh 7-8 V 0h 9 10-19 20-21 22 23-26 27-46 X F X X F F 0h varies 0h 0h varies varies 47 F 8010h 48 49 50 51-52 53 F F F X F 0h 2F00h 4000h 0h 0007h 54 X 3FFFh 55 X 0010h 56 X 003Fh 57-58 X 00FBFC10h 59 F 0101h 60-62 63 64 65 F F 125,045,424 (64GB) 0007h 0003h 66 F 0078h 67 F 0078h 68 F 0078h 69-70 F 0078h F Description General configuration bit-significant information Obsolete-Number of logical cylinders (16,383) Specific configuration Obsolete-Number of logical heads (16) Retired Obsolete-Number of logical sectors per logical track (63) Reserved for assignment by the Compact Flash Association Retired Serial number (20 ASCII characters) Retired Obsolete Firmware revision (8 ASCII characters) Model number 7:0 - Maximum number of sectors transferred per interrupt on multiple commands Reserved Capabilities Capabilities Obsolete Words 88 and 70:64 valid Obsolete - Number of logical cylinders (16,383) Obsolete - Number of logical heads (16) Obsolete - Number of logical sectors per logical track (63) Obsolete Number of sectors transferred per interrupt on multiple commands Total number of user addressable sectors Multi-word DMA modes supported/selected PIO modes supported Minimum multiword DMA transfer cycle time per word Manufacture's recommended multiword DMA transfer cycle time Minimum PIO transfer cycle time without flow control Minimum PIO transfer cycle time with IORDY flow control Specification Specification Word F=Fixed V=Variable X=Both Default Value 71-74 F 0h 75 F 0h 76 77 78 79 80 81 82 83 84 85 86 87 88 89 F F F F V F F F F F V V V V 001Eh 0106h 0h 0048h 0040h 00FCh 001Ah 746Bh 7C01h 6123h 7469h BC01h 6123h 407Fh 90 F 0001h 91 F 0001h 92 93 V V 0h 0FFFEh 94 F 0h 95 V 0h 96 97 98-99 100-103 104 105 106 107 108-111 F V V F V F F 0h 0h 0h 0h 125,045,424 (64GB) 0h 0h 4000h 112-115 F 0h 116 F varies 117-118 F 0h 119 120 V F 0h 0h V Description Reserved (for future command overlap and queuing) Reserved for the IDENTIFY packet DEVICE command Queue depth Serial ATA capabilities Reserved for future Serial ATA definition Serial ATA features supported Serial ATA features enabled Major Version Number Minor Version Number Command set supported Command sets supported Command set /feature supported extension Command set /feature enabled Command set /feature enabled Command set /feature default Ultra DMA modes Time required for security erase unit completion Time required for enhanced security erase completion Current advanced power management value Master Password Revision Code Hardware reset result. The contents of bits (12:0) of this word shall change only during the execution of a hardware reset. Vendor's recommended and actual acoustic management value Stream Minimum Request Size Streaming Transfer Time - DMA Streaming Access Latency - DMA and PIO Streaming Performance Granularity Maximum user LBA for 48-bit Address feature set Streaming Transfer Time - PIO Reserved Physical sector size/logical sector size Inter-seek delay for ISO-7779 acoustic testing in microseconds Unique ID Reserved for word wide name extension to 128 bits Reserved for technical report Words per logical sector 17 Word F=Fixed V=Variable X=Both Default Value Description 121-126 127 128 F F F 401Ch 401Ch 0h 129-159 F 0h 160 161-175 V X 0021h 0h 176-205 F 0h 206-216 217 218-221 222 223-233 234 235 236-254 255 236-254 255 X V F F F F F 0h 0h 0h 0001h 0h 101F 0h 0001h 02A0h 0h varies Supported settings Command set/feature enabled/Supported Reserved Removable Media Status Notification feature set support Security status Vendor specific Compact Flash Association (CFA) power mode 1 Reserved for assignment by the CFA Current media serial number Reserved Non-rotating media device Reserved Reserved Reserved Reserved Reserved Reserved Integrity word (checksum and signature) F X Table 15: Returned Sector Data Notes: 1. F=Fixed. The content of the word is fixed and does not change for removable media devices, these values may change when media is Removed or changed. 2. V=Variable. The state of at least one bit in a word is variable and may change depending on the state of the device or the commands executed by the device. 3. 18 X=F or V. The content of the word may be fixed or variable. Specification 3.2 Power Management Command Set The ASDHS-MLC64G Half-Slim SATA 6 Gb/s SSD supports the power management command set, which consists of CHECK POWER MODE IDLE IDLE IMMEDIATE SLEEP STANDBY STANDBY IMMEDIATE 3.3 Security Mode Feature Set The ASDHS-MLC64G Half-Slim SATA 6 Gb/s SSD supports the Security Mode command set, which consist of SECURITY SET PASSWORD SECURITY UNLOCK SECURITY ERASE PREPARE SECURITY ERASE UNIT SECURITY FREEZE LOCK SECURITY DISABLE PASSWORD 3.4 SMART Command Set The ASDHS-MLC64G SATA SSD supports the SMART command set, which consist of SMART ENABLE OPERATIONS SMART DISABLE OPERATIONS SMART ENABLE/DISABLE AUTOSAVE SMART RETURN STATUS The ASDHS-MLC64G Half-Slim SATA 6 Gb/s SSD supports the the following optional commands. SMART EXECUTE OFF-LINE IMMEDIATE SMART READ DATA SMART READ LOG SMART WRITE LOG Specification 19 The table below lists the SMART commands. Subcommand Code SMART ATTRIBUTE VALUES (READ DATA) D0h READ ATTRIBUTE THRESHOLDS D1h ENABLE/DISABLE ATTRIBUTE AUTOSAVE D2h SAVE ATTRIBUTE VALUES D3h EXECUTE OFF-LINE IMMEDIATE D4h LBA Low value EXECUTE SMART OFF-LINE ROUTINE 00h EXECUTE SMART SHORT SELF-TEST ROUTINE (OFFLINE) 01h EXECUTE SMART EXTENDED SELF-TEST ROUTINE (OFFLINE) 02h ABORT OFF-LINE ROUTINE 7Fh EXECUTE SMART SHORT SELF-TEST ROUTINE (CAPTIVE) 81h EXECUTE SMART EXTENDED SELF-TEST ROUTINE ( CAPTIVE ) 82h READ LOG SECTOR D5h WRITE LOG SECTOR D6h ENABLE SMART OPERATIONS D8h DISABLE SMART OPERATIONS D9h RETURN SMART STATUS DAh Table 16: SMART commands 3.5 Host Protected Area Command Set The ASDHS-MLC64G Half-Slim SATA 6 Gb/s SSD supports the Host Protected Area command set which consists of READ NATIVE MAX ADDRESS SET MAX ADDRESS READ NATIVE MAX ADDRESS EXT SET MAX ADDRESS EXT The ASDHS-MLC64G Half-Slim SATA 6 Gb/s SSD supports the following optional commands. SET MAX SET PASSWORD SET MAX LOCK SET MAX FREEZE LOCK SET MAX UNLOCK 20 Specification 3.6 48-Bit Address Command Set The ASDHS-MLC64G Half-Slim SATA 6 Gb/s SSD supports the Host Protected Area command set, which consists of READ NATIVE MAX ADDRESS FLUSH CACHE EXT READ DMA EXT READ NATIVE MAX ADDRESS EXT READ SECTOR(S) EXT READ VERIFY SECTOR(S) EXT SET MAX ADDRESS EXT WRITE DMA EXT WRITE MULTIPLE EXT WRITE SECTOR(S) EXT 3.7 Device Configuration Overlay Command Set The ASDHS-MLC64G Half-Slim SATA 6 Gb/s SSD supports the Device configuration Overlay command set, which consists of DEVICE CONFIGURATION FREEZE LOCK DEVICE CONFIGURATION IDENTITY DEVICE CONFIGURATION RESTORE DEVICE CONFIGURATION SET 3.8 General Purpose log Command Set The ASDHS-MLC64G Half-Slim SATA 6 Gb/s SSD supports the general purpose log command set, which consists of READ LOG EXT WRITE LOG EXT Specification 21 4 SATA Command Sets 4.1 SATA Command The SATA 3.0 specification is a super set of the ATA/ATAPI-8 specification with regard to supported commands. The ASDHS-MLC64G Half-Slim SATA 6 Gb/s SSD supports the following features which are unique to SATA Specification. 4.1.1. Software Settings Preservation The ASDHS-MLC64G Half-Slim SATA 6 Gb/s SSD supports the SET FEATURES parameter to enable/disable the preservation of software settings. 4.1.2. Native Command Queuing The ASDHS-MLC64G Half-Slim SATA 6 Gb/s SSD supports the Native Command Queuing (NCQ) command set, which includes. READ FPDMA QUEUED WRITE FPDMA QUEUED Note: with a maximum queue depth equal to 31 22 Specification 5 References This document references standards defined by a variety of organizations use the following list to identify the location of an organization's standards information. Date Title Location http://www.vcci.or.jp/vcci_e/general/ join/index.html Dec 2008 VCCI July 2007 ROHS Search for material description datasheet at http://intel.pcnalert.com July 2007 SFF-8144, 1.8" drive form factor http://www.sffcommittee.org February 2007 Serial ATA Revision 2.6 http://www.sata-io.org May 2006 SFF-8223, 2.5" Drive w/Serial Attachment Connector http://www.sffcommittee.org May 2005 SFF-8201, 2.5" drive form factor http://www.sffcommittee.org April 2004 ATA-7 Spec. Volume 1 http://www.t13.org/ Aug. 2009 ATA-8 Spec. Rev 2 http://www.t13.org/ International Electro Technical Commission EB61000 1995 4-2 Personnel Electrostatic Discharge Immunity 1996 4-3 Electromagnetic compatibility (EMC) 1995 4-4 Electromagnetic compatibility (EMC) 1995 4-5 Electromagnetic compatibility (EMC) 1997 4-6Electromagnetic compatibility (EMC) 1994 4-11 (Voltage variations) 1995 ENV 50204 (Radiated electromagnetic field from digital radio telephones) http://www.iec.ch http://www.iec.ch Table 17: Standards References Specification 23 6 Getting Service Contact us should you require any service or assistance. ADLINK Technology, Inc. Address: 9F, No.166 Jian Yi Road, Zhonghe District New Taipei City 235, Taiwan 166 9 Tel: +886-2-8226-5877 Fax: +886-2-8226-5717 Email: service@adlinktech.com Ampro ADLINK Technology, Inc. Address: 5215 Hellyer Avenue, #110, San Jose, CA 95138, USA Tel: +1-408-360-0200 Toll Free: +1-800-966-5200 (USA only) Fax: +1-408-360-0222 Email: info@adlinktech.com ADLINK Technology (China) Co., Ltd. Address: 300 (201203) 300 Fang Chun Rd., Zhangjiang Hi-Tech Park, Pudong New Area, Shanghai, 201203 China Tel: +86-21-5132-8988 Fax: +86-21-5132-3588 Email: market@adlinktech.com ADLINK Technology Beijing Address: 1 E 801 (100085) Rm. 801, Power Creative E, No. 1, B/D Shang Di East Rd., Beijing, 100085 China Tel: +86-10-5885-8666 Fax: +86-10-5885-8625 Email: market@adlinktech.com ADLINK Technology Shenzhen Address: A1 2 C (518057) 2F, C Block, Bldg. A1, Cyber-Tech Zone, Gao Xin Ave. Sec. 7, High-Tech Industrial Park S., Shenzhen, 518054 China Tel: +86-755-2643-4858 Fax: +86-755-2664-6353 Email: market@adlinktech.com 24 Specification LiPPERT ADLINK Technology GmbH Address: Hans-Thoma-Strasse 11, D-68163, Mannheim, Germany Tel: +49-621-43214-0 Fax: +49-621 43214-30 Email: emea@adlinktech.com ADLINK Technology, Inc. (French Liaison Office) Address: 15 rue Emile Baudot, 91300 Massy CEDEX, France Tel: +33 (0) 1 60 12 35 66 Fax: +33 (0) 1 60 12 35 66 Email: france@adlinktech.com ADLINK Technology Japan Corporation Address: 101-0045 3-7-4 374 4F KANDA374 Bldg. 4F, 3-7-4 Kanda Kajicho, Chiyoda-ku, Tokyo 101-0045, Japan Tel: +81-3-4455-3722 Fax: +81-3-5209-6013 Email: japan@adlinktech.com ADLINK Technology, Inc. (Korean Liaison Office) Address: 1675-12 8 8F Mointer B/D,1675-12, Seocho-Dong, Seocho-Gu, Seoul 137-070, Korea Tel: +82-2-2057-0565 Fax: +82-2-2057-0563 Email: korea@adlinktech.com ADLINK Technology Singapore Pte. Ltd. Address: 84 Genting Lane #07-02A, Cityneon Design Centre, Singapore 349584 Tel: +65-6844-2261 Fax: +65-6844-2263 Email: singapore@adlinktech.com ADLINK Technology Singapore Pte. Ltd. (Indian Liaison Office) Address: 1st Floor, #50-56 (Between 16th/17th Cross) Margosa Plaza, Margosa Main Road, Malleswaram, Bangalore-560055, India Tel: +91-80-65605817, +91-80-42246107 Fax: +91-80-23464606 Email: india@adlinktech.com Specification 25 Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: ADLINK Technology: ASDHS-MLC64G-C2 ASDHS-MLC64G-CT