Metallized Polypropylene Film EMI Suppression Capacitors R41, Class Y2, 300 VAC, 110C (Automotive Grade) Overview Applications The R41 is constructed of metallized polypropylene film encapsulated with self-extinguishing resin in a box of material meeting the requirements of UL 94 V-0. For use in electromagnetic interference (EMI) suppression filter in "line-to-ground" and "across-the-line" applications requiring Y2/X1 safety classification. Suitable for use in situations where failure of the capacitor could lead to danger of electric shock. Not for use in "series with mains" type applications. Automotive Grade devices (up to 22.5 mm Lead Spacing) meet the demanding Automotive Electronics Council's AEC- Q200 qualification requirements. Benefits * * * * * * * * * * * * * Approvals: ENEC, UL, cUL, CQC Class Y2 / X1 (IEC 60384-14) Rated voltage: 300 VAC 50/60 Hz Capacitance range: 0.001 - 1 F Lead spacing: 10 - 37.5 mm Capacitance tolerance: 20%, 10% Climatic category: 40/110/56, IEC 60068-1 Tape and reel in accordance with IEC 60286-2 RoHS Compliant and lead-free terminations Operating temperature range of -40C to +110C 100% screening factory test at 5,000 VDC/2,500 VAC Self-healing properties Automotive (AEC-Q200) grades available up to 22.5 mm Lead Spacing Click image above for interactive 3D content Open PDF in Adobe Reader for full functionality Part Number System R41 3 I 2330 00 M1 M Series Rated Voltage (VAC) Lead Spacing (mm) Capacitance Code (pF) Packaging Internal Use Capacitance Tolerance See Ordering Options Table 00 M1 Y2, Metallized Polypropylene 3 = 300 F = 10.0 I = 15.0 N = 22.5 R = 27.5 W = 37.5 The last three digits represent significant figures. The first digit specifies number of zeros to be added. K = 10% M = 20% One world. One KEMET (c) KEMET Electronics Corporation * P.O. Box 5928 * Greenville, SC 29606 * 864-963-6300 * www.kemet.com F3100_R41_Y2_300 * 10/16/2017 1 Metallized Polypropylene Film EMI Suppression Capacitors R41 Series, Class Y2, 300 VAC, 110C (Automotive Grade) Ordering Options Table Lead Spacing Nominal (mm) Lead Length (mm) Lead and Packaging Code 4 +2/-0 H0= 18.5 0.5 00 DQ Tape & Reel (Large Reel) H0= 18.5 0.5 CK Bulk (Bag) - Short Leads 3.5 +0.5/-0 JB Bulk (Bag) - Short Leads 4.0 +0.5/-0 JE Bulk (Bag) - Short Leads 3.2 +0.3/-0.2 JH Bulk (Bag) - Long Leads 18 1 JM Bulk (Bag) - Long Leads 30 +5/-0 40 Bulk (Bag) - Long Leads 25 +2/-1 50 4 +2/-0 H0= 18.5 0.5 00 CK 30 +5/-0 25 +2/-1 40 50 4 +2/-0 00 30 +5/-0 25 +2/-1 40 50 Type of Leads and Packaging Standard Lead and Packaging Options Bulk (Bag) - Short Leads Ammo Pack Other Lead and Packaging Options 10, 15, 22.5 Standard Lead and Packaging Options 27.5 Bulk (Bag) - Short Leads Tape & Reel (Large Reel) Other Lead and Packaging Options Bulk (Bag) - Long Leads Bulk (Bag) - Long Leads Standard Lead and Packaging Options Bulk (Bag) - Short Leads 37.5 Other Lead and Packaging Options Bulk (Bag) - Long Leads Bulk (Bag) - Long Leads (c) KEMET Electronics Corporation * P.O. Box 5928 * Greenville, SC 29606 * 864-963-6300 * www.kemet.com F3100_R41_Y2_300 * 10/16/2017 2 Metallized Polypropylene Film EMI Suppression Capacitors R41 Series, Class Y2, 300 VAC, 110C (Automotive Grade) Dimensions - Millimeters FRONT VIEW SIDE VIEW L B H d LL p p B H L d Nominal Tolerance Nominal Tolerance Nominal Tolerance Nominal Tolerance Nominal Tolerance 10.0 10.0 10.0 15.0 15.0 15.0 15.0 15.0 22.5 22.5 22.5 22.5 22.5 27.5 27.5 27.5 37.5 37.5 37.5 0.4 0.4 0.4 0.4 0.4 0.4 0.4 0.4 0.4 0.4 0.4 0.4 0.4 0.4 0.4 0.4 0.4 0.4 0.4 4.0 5.0 6.0 5.0 6.0 7.5 8.5 11.0 6.0 7.0 8.5 10.0 13.0 13.0 14.0 18.0 13.0 16.0 20.0 +0.2 +0.2 +0.2 +0.2 +0.2 +0.2 +0.2 +0.2 +0.2 +0.2 +0.2 +0.2 +0.2 +0.2 +0.2 +0.2 +0.3 +0.3 +0.3 9.0 11.0 12.0 11.0 12.0 13.5 14.5 19.0 15.0 16.0 17.0 18.5 22.0 22.0 28.0 33.0 24.0 28.5 40.0 +0.1 +0.1 +0.1 +0.1 +0.1 +0.1 +0.1 +0.1 +0.1 +0.1 +0.1 +0.1 +0.1 +0.1 +0.1 +0.1 +0.1 +0.1 +0.1 13.0 13.0 13.0 18.0 18.0 18.0 18.0 18.0 26.5 26.5 26.5 26.5 26.5 32.0 32.0 32.0 41.5 41.5 41.5 +0.2 +0.2 +0.2 +0.3 +0.3 +0.5 +0.5 +0.5 +0.3 +0.3 +0.3 +0.3 +0.3 +0.3 +0.3 +0.3 +0.3 +0.3 +0.3 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 0.8 1.0 1.0 1.0 0.05 0.05 0.05 0.05 0.05 0.05 0.05 0.05 0.05 0.05 0.05 0.05 0.05 0.05 0.05 0.05 0.05 0.05 0.05 Note: See Ordering Options Table for lead length (LL/H0) options. (c) KEMET Electronics Corporation * P.O. Box 5928 * Greenville, SC 29606 * 864-963-6300 * www.kemet.com F3100_R41_Y2_300 * 10/16/2017 3 Metallized Polypropylene Film EMI Suppression Capacitors R41 Series, Class Y2, 300 VAC, 110C (Automotive Grade) Performance Characteristics Polypropylene film Dielectric Plates Metal layer deposited by evaporation under vacuum Winding Non-inductive type Leads Tinned wire Protection Plastic case, thermosetting resin filled. Box material is solvent resistant and flame retardant according to UL94. Related documents IEC 60384-14, EN 60384-14 Rated Voltage (VR) 300 VAC (50/60 Hz), 1,000 VDC Capacitance Range 0.0010 to 1 F Capacitance Values E6 series (IEC 60063) Capacitance Tolerance 10%, 20% Temperature Range -40C to +110C Climatic Category 40/110/56 IEC 60068-1 Storage time: 24 months from the date marked on the label package Average relative humidity per year 70% Storage Conditions RH 85% for 30 days randomly distributed throughout the year Dew is absent Temperature: -40 to 80C (see "Maximum Humidity in Storage Conditions" graph below) Approvals ENEC, UL, cUL, CQC Maximum Humidity in Storage Conditions Relative Humidity (%) 100 90 80 70 60 50 40 30 20 10 0 -40 30 Days Annual Average -20 0 20 40 Temperature (C) 60 80 (c) KEMET Electronics Corporation * P.O. Box 5928 * Greenville, SC 29606 * 864-963-6300 * www.kemet.com F3100_R41_Y2_300 * 10/16/2017 4 Metallized Polypropylene Film EMI Suppression Capacitors R41 Series, Class Y2, 300 VAC, 110C (Automotive Grade) Performance Characteristics cont'd Dissipation Factor (tan) Test Voltage Between Terminals 0.3% (0.2%*) at 1kHz , +25C 5C (* typical value) The 100% screening factory test is carried out at 5,000 VDC/2,500 VAC. The voltage level is selected to meet the requirements in applicable equipment standards. All electrical characteristics are checked after the test. It is not permitted to repeat this test as there is a risk to damage the capacitor. KEMET is not liable in such case for any failures. Measured at +25C 5C, according to IEC 60384-2 Insulation Resistance Minimum Values Between Terminals Voltage Charge Voltage Charge Time C 0.33 F C > 0.33 F 1 min 1 * 105 M ( 5 * 105 M )* 30,000 M * F ( 150,000 M * F )* 100 VDC In DC Applications Recommended voltage 1,000 VDC * Typical value Qualification Automotive grade products meet or exceed the requirements outlined by the Automotive Electronics Council. Details regarding test methods and conditions are referenced in document AEC-Q200, Stress Test Qualification for Passive Components. For additional information regarding the Automotive Electronics Council and AEC-Q200, please visit their website at www.aecouncil.com. Impedance Graph (c) KEMET Electronics Corporation * P.O. Box 5928 * Greenville, SC 29606 * 864-963-6300 * www.kemet.com F3100_R41_Y2_300 * 10/16/2017 5 Metallized Polypropylene Film EMI Suppression Capacitors R41 Series, Class Y2, 300 VAC, 110C (Automotive Grade) Environmental Test Data Test IEC Publication Procedure Endurance EN/IEC 60384-14 Vibration IEC 60068-2-6 Test Fc 3 directions at 2 hours each 10 - 55 Hz at 0.75 mm or 98 m/s2 Bump IEC 60068-2-29 Test Eb 1,000 bumps at 390 m/s2 Change of Temperature IEC 60068-2-14 Test Na Upper and lower rated temperature 5 cycles Active Flammability IEC 60384-14 VR +20 surge pulses at 5 kV (pulse every 5 seconds) Passive Flammability IEC 60384-14 IEC 60384-1, IEC 60695-11-5 Needle flame test Damp Heat Steady State IEC 60068-2-78 Test Cab 1.7 x VR VAC 50 Hz, once every hour increase to 1,000 VAC for 0.1 second, 1,000 hours at upper rated temperature +40C and 93% RH, 56 days Approvals Mark Specification File Number EN/IEC 60384-14 V4160 UL 60384-14 and CAN/CSA E60384-14 (300 VAC) E97797 IEC 60384-14 CQC13001087758 CQC13001101264 CQC14001116018 CQC14001116611 Environmental Compliance All KEMET EMI capacitors are RoHS Compliant. (c) KEMET Electronics Corporation * P.O. Box 5928 * Greenville, SC 29606 * 864-963-6300 * www.kemet.com F3100_R41_Y2_300 * 10/16/2017 6 Metallized Polypropylene Film EMI Suppression Capacitors R41 Series, Class Y2, 300 VAC, 110C (Automotive Grade) Table 1 - Ratings & Part Number Reference Dimensions in mm Capacitance Value (F) B H 0.0010 0.0015 0.0022 0.0033 0.0047 0.0068 0.010 0.0033 0.0047 0.0068 0.010 0.015 0.022 0.033 0.047 0.068 0.047 0.068 0.068 0.10 0.15 0.22 0.22 0.33 0.47 0.68 0.47 0.68 1.0 4.0 4.0 4.0 4.0 5.0 6.0 6.0 5.0 5.0 5.0 5.0 5.0 6.0 7.5 8.5 11.0 6.0 6.0 7.0 8.5 10.0 13.0 13.0 14.0 18.0 18.0 13.0 16.0 20.0 9.0 9.0 9.0 9.0 11.0 12.0 12.0 11.0 11.0 11.0 11.0 11.0 12.0 13.5 14.5 19.0 15.0 15.0 16.0 17.0 18.5 22.0 22.0 28.0 33.0 33.0 24.0 28.5 40.0 Capacitance Value (F) B (mm) H (mm) L Lead Spacing (p) dV/dt (V/s) New KEMET Part Number Legacy Part Number 13.0 13.0 13.0 13.0 13.0 13.0 13.0 18.0 18.0 18.0 18.0 18.0 18.0 18.0 18.0 18.0 26.5 26.5 26.5 26.5 26.5 26.5 32.0 32.0 32.0 32.0 41.5 41.5 41.5 10.0 10.0 10.0 10.0 10.0 10.0 10.0 15.0 15.0 15.0 15.0 15.0 15.0 15.0 15.0 15.0 22.5 22.5 22.5 22.5 22.5 22.5 27.5 27.5 27.5 27.5 37.5 37.5 37.5 800 800 800 800 800 800 800 600 600 600 600 600 600 600 600 600 500 500 500 500 500 500 400 400 400 400 300 300 300 413F1100(1)00(2) 413F1150(1)00(2) 413F1220(1)00(2) 413F1330(1)M1(2) 413F1470(1)M1(2) 413F1680(1)00(3) 413F2100(1)M1(3) 413I1330(1)00(2) 413I1470(1)00(2) 413I1680(1)00(2) 413I2100(1)00(2) 413I2150(1)M1(2) 413I2220(1)M1(2) 413I2330(1)M1(2) 413I2470(1)M1(2) 413I2680(1)00(2) 413N2470(1)00(2) 413N2680(1)M1(3) 413N2680(1)00(2) 413N3100(1)M1(2) 413N3150(1)M1(2) 413N3220(1)00(2) 413R3220(1)00(2) 413R3330(1)00(2) 413R3470(1)00(2) 413R3680(1)00(2) 413W 3470(1)00(2) 413W 3680(1)00(2) 413W 4100(1)00(2) R413F1100(1)00(2) R413F1150(1)00(2) R413F1220(1)00(2) R413F1330(1)M1(2) R413F1470(1)M1(2) R413F1680(1)00(3) R413F2100(1)M1(3) R413I1330(1)00(2) R413I1470(1)00(2) R413I1680(1)00(2) R413I2100(1)00(2) R413I2150(1)M1(2) R413I2220(1)M1(2) R413I2330(1)M1(2) R413I2470(1)M1(2) R413I2680(1)00(2) R413N2470(1)00(2) R413N2680(1)M1(3) R413N2680(1)00(2) R413N3100(1)M1(2) R413N3150(1)M1(2) R413N3220(1)00(2) R413R3220(1)00(2) R413R3330(1)00(2) R413R3470(1)00(2) R413R3680(1)00(2) R413W 3470(1)00(2) R413W 3680(1)00(2) R413W 4100(1)00(2) L (mm) Lead Spacing (p) dV/dt (V/s) New KEMET Part Number Legacy Part Number (1) Insert lead and packaging code. See Ordering Options Table for available options. (2) M = 20%, K = 10% (3) M = 20% (only available tolerance). (c) KEMET Electronics Corporation * P.O. Box 5928 * Greenville, SC 29606 * 864-963-6300 * www.kemet.com F3100_R41_Y2_300 * 10/16/2017 7 Metallized Polypropylene Film EMI Suppression Capacitors R41 Series, Class Y2, 300 VAC, 110C (Automotive Grade) Soldering Process The implementation of the RoHS directive has resulted in the selection of SnAgCu (SAC) alloys or SnCu alloys as primary solder. This has increased the liquidus temperature from that of 183C for SnPb eutectic alloy to 217 - 221C for the new alloys. As a result, the heat stress to the components, even in wave soldering, has increased considerably due to higher pre-heat and wave temperatures. Polypropylene capacitors are especially sensitive to heat (the melting point of polypropylene is 160 - 170C). Wave soldering can be destructive, especially for mechanically small polypropylene capacitors (with lead spacing of 5 mm to 15 mm), and great care has to be taken during soldering. The recommended solder profiles from KEMET should be used. Please consult KEMET with any questions. In general, the wave soldering curve from IEC Publication 61760-1 Edition 2 serves as a solid guideline for successful soldering. Please see Figure 1. Reflow soldering is not recommended for through-hole film capacitors. Exposing capacitors to a soldering profile in excess of the above the recommended limits may result to degradation or permanent damage to the capacitors. Do not place the polypropylene capacitor through an adhesive curing oven to cure resin for surface mount components. Insert through-hole parts after the curing of surface mount parts. Consult KEMET to discuss the actual temperature profile in the oven, if through-hole components must pass through the adhesive curing process. A maximum two soldering cycles is recommended. Please allow time for the capacitor surface temperature to return to a normal temperature before the second soldering cycle. Manual Soldering Recommendations Wave Soldering Recommendations 300 The following is the recommendation for manual soldering with a soldering iron. 2 +3 seconds maximum 260C 250 First wave Recommended Soldering Temperature Temperature (C) 200 400 350 Soldering iron bit temperature (C) Second wave 300 Cooling T <150C Preheating 150 ca 2C/second ca 3.5C/second typical T preheat 100 ca 5C/second 115 C max 100 C Typical 250 50 200 150 0 0 100 40 80 120 160 200 240 Time (s) 50 0 0 1 2 3 4 5 6 7 8 Soldering time (seconds) The soldering iron tip temperature should be set at 350C (+10C maximum) with the soldering duration not to exceed more than 3 seconds. (c) KEMET Electronics Corporation * P.O. Box 5928 * Greenville, SC 29606 * 864-963-6300 * www.kemet.com F3100_R41_Y2_300 * 10/16/2017 8 Metallized Polypropylene Film EMI Suppression Capacitors R41 Series, Class Y2, 300 VAC, 110C (Automotive Grade) Soldering Process cont'd Wave Soldering Recommendations cont'd 1. The table indicates the maximum set-up temperature of the soldering process Figure 1 Dielectric Film Material Maximum Preheat Temperature Maximum Peak Soldering Temperature Capacitor Capacitor Capacitor Capacitor Capacitor Pitch Pitch Pitch Pitch Pitch 10 mm = 15 mm > 15 mm 15 mm > 15 mm Polyester 130C 130C 130C 270C 270C Polypropylene 100C 110C 130C 260C 270C Paper 130C 130C 140C 270C 270C Polyphenylene Sulphide 150C 150C 160C 270C 270C 2. The maximum temperature measured inside the capacitor: Set the temperature so that inside the element the maximum temperature is below the limit: Dielectric Film Material Maximum temperature measured inside the element Polyester 160C Polypropylene 110C Paper 160C Polyphenylene sulphide 160C Temperature monitored inside the capacitor. Selective Soldering Recommendations Selective dip soldering is a variation of reflow soldering. In this method, the printed circuit board with through-hole components to be soldered is preheated and transported over the solder bath as in normal flow soldering without touching the solder. When the board is over the bath, it is stopped and pre-designed solder pots are lifted from the bath with molten solder only at the places of the selected components, and pressed against the lower surface of the board to solder the components. The temperature profile for selective soldering is similar to the double wave flow soldering outlined in this document, however, instead of two baths, there is only one bath with a time from 3 to 10 seconds. In selective soldering, the risk of overheating is greater than in double wave flow soldering, and great care must be taken so that the parts are not overheated. (c) KEMET Electronics Corporation * P.O. Box 5928 * Greenville, SC 29606 * 864-963-6300 * www.kemet.com F3100_R41_Y2_300 * 10/16/2017 9 Metallized Polypropylene Film EMI Suppression Capacitors R41 Series, Class Y2, 300 VAC, 110C (Automotive Grade) Construction 2 Sections Molded Plastic Case Single-sided Metallized Polypropylene Film (First Layer) Detailed Cross Section Molded Plastic Self-Extinguishing Case Resin Single-sided Metallized Polypropylene Film (Second Layer) Margin Margin Metal Contact Layer Metal Contact Layer FILM WINDINGMargin SCHEME OPTIONS Leads etallized Polypropylene Film Double-sided Metallized Polyester Film Winding Scheme sided ized pylene m Single-sided Metallized Polypropylene Film Single-sided Metallized Polypropylene Film 4 Sections Double-sided Metallized Polyester Carrier Film Polypropylene Film Dielectric Double-sided Metallized Polyester Carrier Film 3 Sections (c)Metallized KEMET Electronics Corporation * P.O. Box 5928 * Greenville, SC 29606 * 864-963-6300 * www.kemet.com Polyphenylene Sulfide Film (SMR) 2 Sections 1 Section 2 Sections sided ized pylene m Double-sided Metallized Polypropylene Polyester Carrier Film Dielectric Film Double-sided Metallized Polyester Carrier Film 4 Sections F3100_R41_Y2_300 * 10/16/2017 Polypropylene Film/Foil 10 Metallized Polypropylene Film EMI Suppression Capacitors R41 Series, Class Y2, 300 VAC, 110C (Automotive Grade) Marking Lead Spacing 10 mm FRONT TOP Series, Dielectric Code, Safety Class, Self Healing Capacitance, Rated Voltage Approval Marks Manufacturer's Logo IEC Climatic Category Capacitance Tolerance Date Code Passive Flammability Category Manufacturing Plant Lead Spacing 15 mm, 22.5 mm (small case sizes) FRONT TOP Series, Dielectric Code, Safety Class, Self Healing Capacitance, Rated Voltage Approval Marks Manufacturer's Logo IEC Climatic Category Capacitance Tolerance Date Code Passive Flammability Category: B for volume 1750 mm3 C for volume < 1750 mm3 Manufacturing Plant Lead Spacing 22.5 mm (large case sizes), 27.5 mm, 37.5 mm FRONT TOP Series Dielectric Code Approval Marks Manufacturer's Logo IEC Climatic Category Passive Flammability (c) KEMET Electronics Corporation * P.O. Box 5928 * Greenville, SC 29606 * 864-963-6300 * www.kemet.com Category Safety Class Self Healing Capacitance, Capacitance Tolerance, Rated Voltage QA Number Manufacturing Date Code Plant F3100_R41_Y2_300 * 10/16/2017 11 Manufacturing Plant Passive Flammability Category: Metallized Polypropylene Film EMI Suppression Capacitors B for volume 1750 mm3 R41 Series, Class Y2, 300C VAC, 110C <(Automotive for volume 1750 mm3 Grade) Marking cont'd Lead Spacing 22.5 mm (large case sizes), 27.5 mm, 37.5 mm FRONT TOP Series Dielectric Code Safety Class Self Healing Capacitance, Capacitance Tolerance, Rated Voltage Manufacturer's Logo Approval Marks IEC Climatic Category QA Number Passive Flammability Category Manufacturing Plant Date Code Manufacturing Date Code (IEC 60062) Y = Year, Z = Month Year Code Month Code 2000 2001 2002 2003 2004 2005 2006 2007 2008 2009 2010 2011 2012 2013 2014 2015 2016 2017 2018 2019 2020 M N P R S T U V W X A B C D E F H J K L M January February March April May June July August September October November December 1 2 3 4 5 6 7 8 9 O N D (c) KEMET Electronics Corporation * P.O. Box 5928 * Greenville, SC 29606 * 864-963-6300 * www.kemet.com F3100_R41_Y2_300 * 10/16/2017 12 Metallized Polypropylene Film EMI Suppression Capacitors R41 Series, Class Y2, 300 VAC, 110C (Automotive Grade) Packaging Quantities Lead Spacing (mm) Thickness (mm) Height (mm) Length (mm) Bulk Short Leads Bulk Long Leads Standard Reel o 355 mm Large Reel o 500 mm Ammo Taped 10 4.0 5.0 6.0 9.0 11.0 12.0 13.0 13.0 13.0 2000 1300 1000 1800 1500 1200 750 600 500 1500 1250 1000 1000 800 680 15 5.0 6.0 7.5 8.5 11.0 11.0 12.0 13.5 14.5 19.0 18.0 18.0 18.0 18.0 18.0 2000 1750 1000 1000 450 1000 900 700 500 350 600 500 350 300 - 1250 1000 800 700 500 800 680 500 440 340 22.5 6.0 7.0 8.5 10.0 13.0 15.0 16.0 17.0 18.5 22.0 26.5 26.5 26.5 26.5 26.5 805 700 468 396 300 500 500 300 300 200 - - - - - 700 550 450 350 300 464 380 280 235 - 27.5 13.0 14.0 18.0 22.0 28.0 33.0 32.0 32.0 32.0 480 352 256 288 176 128 - - - 300 - - - - - 37.5 13.0 16.0 20.0 24.0 28.5 40.0 41.5 41.5 41.5 360 216 126 216 108 84 - - - - - - - - - (c) KEMET Electronics Corporation * P.O. Box 5928 * Greenville, SC 29606 * 864-963-6300 * www.kemet.com F3100_R41_Y2_300 * 10/16/2017 13 Metallized Polypropylene Film EMI Suppression Capacitors R41 Series, Class Y2, 300 VAC, 110C (Automotive Grade) Lead Taping & Packaging (IEC 60286-2) Figure 1 Lead Spacing 10 mm Figure 2 Lead Spacing 15 mm Figure 3 Lead Spacing 22.5 - 27.5 mm P W2 P2 od A B W W0 W1 H0 P1 P0 F P h h D0 P1 P2 A-B t Taping Specification Dimensions (mm) Description Symbol 10 Fig. 1 Lead Space 15 22.5 Fig. 2 Fig. 3 27.5 Fig. 3 Tol. Lead wire diameter d 0.6 0.6-0.8 0.8 0.8 0.05 Taping lead space P 25.4 25.4 38.1 38.1 1 Feed hole lead space * P0 12.7 12.7 12.7 12.7 0.2 ** Centering of the lead wire P1 7.7 5.2 7.8 5.3 0.7 Centering of the body P2 12.7 12.7 19.05 19.05 1.3 Lead spacing (pitch) *** F 10 15 22.5 27.5 +0.6/-0.1 Component alignment h 0 0 0 0 2 Height of component from tape center H 0 **** 18.5 18.5 18.5 18.5 0.5 Carrier tape width W 18 18 18 18 +1 / -0.5 Hold down tape width W0 9 10 10 10 Minimum Hole position W1 9 9 9 9 0.5 Hold down tape position W2 3 3 3 3 Maximum Feed hole diameter D0 4 4 4 4 0.2 Total tape thickness t 0.7 0.7 0.7 0.7 0.2 * Available also in 15 mm. ** Maximum 1 mm on 20 lead spaces. *** Pitches 15 mm and 10 mm taped to 7.5 mm (crimped leads) available upon request. **** H0 = 16.5 mm available upon request. (c) KEMET Electronics Corporation * P.O. Box 5928 * Greenville, SC 29606 * 864-963-6300 * www.kemet.com F3100_R41_Y2_300 * 10/16/2017 14 Metallized Polypropylene Film EMI Suppression Capacitors R41 Series, Class Y2, 300 VAC, 110C (Automotive Grade) Lead Taping & Packaging (IEC 60286-2) cont'd Ammo Specifications Dimensions (mm) H W T 360 340 59 H T W Reel Specifications Reel Size Standard Large Dimensions (mm) D H W 355 500 30 25 55 Maximum D H W (c) KEMET Electronics Corporation * P.O. Box 5928 * Greenville, SC 29606 * 864-963-6300 * www.kemet.com F3100_R41_Y2_300 * 10/16/2017 15 Metallized Polypropylene Film EMI Suppression Capacitors R41 Series, Class Y2, 300 VAC, 110C (Automotive Grade) KEMET Electronics Corporation Sales Offices For a complete list of our global sales offices, please visit www.kemet.com/sales. Disclaimer All product specifications, statements, information and data (collectively, the "Information") in this datasheet are subject to change. The customer is responsible for checking and verifying the extent to which the Information contained in this publication is applicable to an order at the time the order is placed. All Information given herein is believed to be accurate and reliable, but it is presented without guarantee, warranty, or responsibility of any kind, expressed or implied. Statements of suitability for certain applications are based on KEMET Electronics Corporation's ("KEMET") knowledge of typical operating conditions for such applications, but are not intended to constitute - and KEMET specifically disclaims - any warranty concerning suitability for a specific customer application or use. The Information is intended for use only by customers who have the requisite experience and capability to determine the correct products for their application. Any technical advice inferred from this Information or otherwise provided by KEMET with reference to the use of KEMET's products is given gratis, and KEMET assumes no obligation or liability for the advice given or results obtained. Although KEMET designs and manufactures its products to the most stringent quality and safety standards, given the current state of the art, isolated component failures may still occur. Accordingly, customer applications which require a high degree of reliability or safety should employ suitable designs or other safeguards (such as installation of protective circuitry or redundancies) in order to ensure that the failure of an electrical component does not result in a risk of personal injury or property damage. Although all product-related warnings, cautions and notes must be observed, the customer should not assume that all safety measures are indicted or that other measures may not be required. KEMET is a registered trademark of KEMET Electronics Corporation. (c) KEMET Electronics Corporation * P.O. Box 5928 * Greenville, SC 29606 * 864-963-6300 * www.kemet.com F3100_R41_Y2_300 * 10/16/2017 16