19-2403; Rev 0; 8/95 15kV ESD-Protected, Quad, Low-Power RS-232 Line Driver ________________________Applications ____________________________Features ESD Protection: 15kV--Human Body Model 6kV--IEC801-2, Contact Discharge 15kV--IEC801-2, Air-Gap Discharge Latchup Free, Even During an ESD Event Low 85A Supply Current from IEE or ICC Guaranteed 120kbps Data Rate No External Capacitors Required for Slew-Rate Limiting Pin Compatible with MC1488, MC14C88, SN75188, SN75C188, DS1488, and DS14C88 ______________Ordering Information PART TEMP. RANGE Modems MAX1488ECPD 0C to +70C 14 Plastic DIP Interface Data Terminal Equipment (DTE) with Data Circuit-Terminating Equipment (DCE) MAX1488ECSD MAX1488EC/D MAX1488EEPD 0C to +70C 0C to +70C -40C to +85C 14 SO Dice* 14 Plastic DIP PC Motherboards Equipment Meeting IEC1000-4-2 (formerly IEC801-2) or 15kV ESD Protection __________Typical Operating Circuit 14 MAX1488E 14 MAX1489E MAX1488EESD -40C to +85C * Dice are specified at TA = +25C. INTERCONNECTING CABLE TTL/CMOS LOGIC 14 MAX1488E 14 MAX1489E 14 SO __________________Pin Configuration TOP VIEW VEE 1 TTL/CMOS LOGIC PIN-PACKAGE INPUT A 2 14 VCC MAX1488E 13 INPUT D1 OUTPUT A 3 12 INPUT D2 INPUT B1 4 11 OUTPUT D INPUT B2 5 10 INPUT C1 OUTPUT B 6 9 INPUT C2 GND 7 8 OUTPUT C SIGNAL GROUND PC MOTHERBOARD (DTE) MODEM (DCE) DIP/SO ________________________________________________________________ Maxim Integrated Products Call toll free 1-800-998-8800 for free samples or literature. 1 MAX1488E _______________General Description The MAX1488E quad, low-power line driver is designed for EIA/TIA-232, EIA/TIA-562, and CCITT V.28 communications in harsh environments. Each transmitter output is protected against 15kV electrostatic discharge (ESD) shocks. The inputs are TTL and CMOS compatible with minimal loading. The outputs feature internally controlled slew-rate limiting and current limiting. This device has a guaranteed 120kbps data rate. Powersupply current is less than 180A over a 4.5V to 13.2V supply voltage range. The MAX1488E is pin compatible with the MC1488, MC14C88, SN75188, SN75C188, DS1488, and DS14C88. It is available in 14-pin plastic DIP and SO packages. MAX1488E 15kV ESD-Protected, Quad, Low-Power RS-232 Line Driver ABSOLUTE MAXIMUM RATINGS Positive Supply Voltage (VCC) .............................................+14V Negative Supply Voltage (VEE) .............................................-14V Input Voltage (VIN) .................................................-0.3V to +15V Driver Output Voltage ..........................................................15V Continuous Power Dissipation (TA = +70C) Plastic DIP (derate 10.00mW/C above +70C) ..........800mW SO (derate 8.7mW/C above +70C) ...........................695mW Operating Temperature Ranges MAX1488EC_D ...................................................0C to +70C MAX1488EE_D ................................................-40C to +85C Storage Temperature Range .............................-65C to +160C Lead Temperature (soldering, 10sec) .............................+300C Stresses beyond those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. ELECTRICAL CHARACTERISTICS (VCC = 4.5V to 13.2V, VEE = -4.5V to -13.2V, TA = TMIN to TMAX, unless otherwise noted. Typical values are at TA = +25C.) PARAMETER SYMBOL CONDITIONS MIN TYP 3.7 5 10 4.0 5.4 10.5 MAX UNITS DC CHARACTERISTICS Output Voltage High Output Voltage Low Operating Voltage Range VOH VOL VCC = -VEE = 5.0V, RL = 3k VCC = -VEE = 6.5V, RL = 3k VCC = -VEE = 12.0V, RL = 3k VCC = -VEE = 13.2V, RL = open VCC = -VEE = 5.0V, RL = 3k VCC = -VEE = 6.5V, RL = 3k VCC = -VEE = 12.0V, RL = 3k VCC = -VEE = 13.2V, RL = open -4.5 -5.8 -10.8 V 13.2 -3.7 -5 -10 VCC -13.2 4.5 13.2 VEE -13.2 -4.5 Positive Supply Current ICC No load Negative Supply Current IEE No load Output Short-Circuit Current IOS Output shorted to ground (Note 1) Input High Voltage VIH Input Low Voltage VIL Input Current IIN1 Output Resistance RO 85 -180 -85 4 20 V V 180 A 45 mA A 2.0 V 0 0.8 V 2 A VCC = VEE = 0V IVOI 2.0V 300 VCC = 4.5V, VEE = -4.5V, CL = 50pF 2.4 3.5 VCC = 9.0V, VEE = -9.0V, CL = 50pF 2.8 3.9 VCC = 12.0V, VEE = -12.0V, CL = 50pF 3.1 4.2 VCC = 4.5V, VEE = -4.5V, CL = 50pF 2.1 4.5 VCC = 9.0V, VEE = -9.0V, CL = 50pF 2.4 5.1 VCC = 12.0V, VEE = -12.0V, CL = 50pF 2.6 5.4 VCC = 4.5V, VEE = -4.5V, CL = 50pF 0.25 VCC = 9.0V, VEE = -9.0V, CL = 50pF 0.42 VCC = 12.0V, VEE = -12.0V, CL = 50pF 0.42 Human Body Model 15 TIMING CHARACTERISTICS (see Figure 1) Output Propagation Delay, Low to High Output Propagation Delay, High to Low Propagation Delay Skew, ItPLH - tPHLI tPLH tPHL tSK s s s ESD CHARACTERISTICS ESD Protection 2 IEC-1000-4-2 (Contact Discharge) 6 IEC-1000-4-2 (Air-Gap Discharge) 15 _______________________________________________________________________________________ kV 15kV ESD-Protected, Quad, Low-Power RS-232 Line Driver MAX1488E ELECTRICAL CHARACTERISTICS (continued) (VCC = 4.5V to 13.2V, VEE = -4.5V to -13.2V, TA = TMIN to TMAX, unless otherwise noted. Typical values are at TA = +25C.) PARAMETER SYMBOL MIN TYP tR1 850 tR2 CL = 1500pF, RL = 5k, VOUTPUT_ from -3.0V to 3.0V 740 tF1 CL = 1500pF, RL = 5k, VOUTPUT_ from -3.3V to 3.3V 860 tF2 CL = 1500pF, RL = 5k, VOUTPUT_ from -3.0V to 3.0V 765 SR CL = 15pF to 2500pF, RL = 3k to 7k, VCC = 12V, VEE = -12V, TA = +25C, VOUTPUT_ from -3.0V to 3.0V 4 CL = 15pF to 2500pF, RL = 3k to 7k, VCC = 12V, VEE = -12V, TA = +25C 120 Output Rise Time Output Fall Time Output Slew Rate CONDITIONS CL = 1500pF, RL = 5k, VOUTPUT_ from -3.3V to 3.3V Guaranteed Data Rate MAX UNITS ns ns 30 V/s kbps Note 1: The IOS value is for one output at a time. If more than one output is shorted simultaneously, damage may occur. __________________________________________Typical Operating Characteristics (VCC = 12V, VEE = -12V, TA = +25C, unless otherwise noted.) RL= 3k 10 RL= 3k VOH 5 0 -5 VOL RL= 3k -10 9 RISING EDGE 8 7 FALLING EDGE 6 5 RL= 5k 4 5 6 7 8 9 10 11 12 13 14 VCC AND -VEE SUPPLIES (V) VOH @ VCC = -VEE = 12V 10 5 3 VOH @ VCC = -VEE = 4.5V 0 VOL @ VCC = -VEE = 4.5V -5 -10 4 -15 15 MAX1488E TOC-3 11 SLEW RATE (V/s) OUTPUT VOLTAGE (V) 10 OUTPUT VOLTAGE vs. TEMPERATURE OUTPUT VOLTAGE (V) RL= 5k MAX1488E TOC-1 15 SLEW RATE vs. LOAD CAPACITANCE MAX1488E TOC-2 OUTPUT VOLTAGE vs. SUPPLY VOLTAGE VOL @ VCC = -VEE = 12V RL= 3k -15 0 500 1000 1500 2000 LOAD CAPACITANCE (pF) 2500 3000 -40 -20 0 20 40 60 80 100 TEMPERATURE (C) _______________________________________________________________________________________ 3 MAX1488E 15kV ESD-Protected, Quad, Low-Power RS-232 Line Driver _____________________Pin Description 3.0V DRIVER INPUT 0V PIN NAME FUNCTION 1 VEE -4.5V to -13.2V Supply Voltage Input 2, 4, 5, 9, 10, 12, 13 INPUT_ 3, 6, 8, 11 OUTPUT_ 7 GND Ground 14 VCC +4.5V to +13.2V Supply Voltage Input 1.5V TPHL TPLH VOH Driver Inputs 3.3V 3.0V Driver Outputs VOUT 0V -3.0V -3.3V _______________Detailed Description tF2 tR2 The MAX1488E provides 15kV of ESD protection when operating or when powered down. After an ESD event, the MAX1488E will not latch up. Internal slew-rate-limiting circuitry eliminates the need for external capacitors. The MAX1488E has a guaranteed 120kbps data rate. tF1 tR1 Outputs Tables 1 and 2 describe the output states. The output voltage level is affected by both the load current and supply voltage, and is stable over temperature. Refer to the Typical Operating Characteristics to see how the output voltage varies with supply voltage, load capacitance, and temperature. Table 1. Driver A Functions INPUT A H L OUTPUTA L H Table 2. Driver B-D Functions INPUT_1 H L INPUT_2 H X OUTPUT_ L H X L H Inputs The driver inputs determine the driver output states (Tables 1 and 2). Driver inputs B, C, and D have two inputs. Connect unused inputs to ground or VCC. 15kV ESD Protection As with all Maxim devices, ESD-protection structures are incorporated on all pins to protect against electrostatic discharges encountered during handling and assembly. The MAX1488E driver outputs have extra protection against static electricity found in normal 4 VOL SIGNAL GENERATOR RL CL Figure 1. Slew-Rate Test Circuit and Timing Diagram operation. Maxim's engineers developed state-of-theart structures to protect these pins against ESD of 15kV, without damage. After an ESD event, the MAX1488E keeps working without latchup. ESD protection can be tested in various ways; the transmitter outputs are characterized for protection to the following: 1) 15kV using the Human Body Model 2) 6kV using the Contact-Discharge Method specified in IEC1000-4-2 (formerly IEC801-2) 3) 15kV using the Air-Gap Method specified in IEC1000-4-2 (formerly IEC801-2). ESD Test Conditions ESD performance depends on a number of conditions. Contact Maxim for a reliability report that documents test setup, methodology, and results. Human Body Model Figure 2a shows the Human Body Model, and Figure 2b shows the current waveform it generates when discharged into a low impedance. This model consists of a 100pF capacitor charged to the ESD voltage of interest, which is then discharged into the test device through a 1.5k resistor. _______________________________________________________________________________________ 15kV ESD-Protected, Quad, Low-Power RS-232 Line Driver CHARGE-CURRENT LIMIT RESISTOR HIGHVOLTAGE DC SOURCE Cs 100pF R C 50M to 100M R D 1500 DISCHARGE RESISTANCE CHARGE-CURRENT LIMIT RESISTOR DEVICE UNDER TEST STORAGE CAPACITOR Figure 2a. Human Body ESD Test Model IP 100% 90% Cs 150pF R D 330 DISCHARGE RESISTANCE STORAGE CAPACITOR DEVICE UNDER TEST Figure 3a. IEC1000-4-2 ESD Test Model I 100% 90% PEAK-TO-PEAK RINGING (NOT DRAWN TO SCALE) I PEAK Ir HIGHVOLTAGE DC SOURCE MAX1488E R C 1M AMPERES 36.8% 10% 0 10% 0 tRL TIME tDL CURRENT WAVEFORM t r = 0.7ns to 1ns t 30ns 60ns Figure 2b. Human Body Model Current Waveform Figure 3b. IEC1000-4-2 ESD Generator Current Waveform IEC1000-4-2 The IEC1000-4-2 standard covers ESD testing and performance of finished equipment; it does not specifically refer to integrated circuits. The MAX1488E helps you design equipment that meets Level 4 (the highest level) of IEC1000-4-2, without additional ESD-protection components. The major difference between tests done using the Human Body Model and IEC1000-4-2 is higher peak current in IEC1000-4-2. Because series resistance is lower in the IEC1000-4-2 ESD test model (Figure 3a), the ESD withstand voltage measured to this standard is generally lower than that measured using the Human Body Model. Figure 3b shows the current waveform for the 6kV IEC1000-4-2 Level 4 ESD Contact-Discharge test. The Air-Gap test involves approaching the device with a charged probe. The Contact-Discharge method connects the probe to the device before the probe is energized. Machine Model The Machine Model for ESD testing uses a 200pF storage capacitor and zero-discharge resistance. Its objective is to mimic the stress caused by contact that occurs with handling and assembly during manufacturing. Of course, all pins (not just RS-232 inputs and outputs) require this protection during manufacturing. Therefore, the Machine Model is less relevant to the I/O ports than the Human Body Model and IEC1000-4-2. __________Applications Information Use proper layout to ensure other devices on your board are not damaged in an ESD strike. Currents as high as 60A can instantaneously pass into the ground, so it is important to minimize the ground-lead return path to the power supply. A separate return path to the power supply is recommended. Trace widths should be greater than 40 mils. VCC and VEE must be bypassed with 0.1F capacitors as close to the part as possible to ensure maximum ESD protection. _______________________________________________________________________________________ 5 MAX1488E 15kV ESD-Protected, Quad, Low-Power RS-232 Line Driver ___________________Chip Topography V SS V DD INPUT D1 INPUT A INPUT D2 0.134" (3.40mm) OUTPUT A OUTPUT D INPUT B1 INPUT C1 INPUT B2 INPUT C2 OUTPUT B OUTPUT C GND 0.070" (1.78mm) TRANSISTOR COUNT: 95 SUBSTRATE CONNECTED TO GND 6 _______________________________________________________________________________________ 15kV ESD-Protected, Quad, Low-Power RS-232 Line Driver DIM D 0-8 A 0.101mm 0.004in. e B A1 E C H L Narrow SO SMALL-OUTLINE PACKAGE (0.150 in.) A A1 B C E e H L INCHES MAX MIN 0.069 0.053 0.010 0.004 0.019 0.014 0.010 0.007 0.157 0.150 0.050 0.244 0.228 0.050 0.016 DIM PINS D D D 8 14 16 MILLIMETERS MIN MAX 1.35 1.75 0.10 0.25 0.35 0.49 0.19 0.25 3.80 4.00 1.27 5.80 6.20 0.40 1.27 INCHES MILLIMETERS MIN MAX MIN MAX 0.189 0.197 4.80 5.00 0.337 0.344 8.55 8.75 0.386 0.394 9.80 10.00 21-0041A _______________________________________________________________________________________ 7 MAX1488E ________________________________________________________Package Information MAX1488E 15kV ESD-Protected, Quad, Low-Power RS-232 Line Driver ___________________________________________Package Information (continued) D E DIM E1 A A1 A2 A3 B B1 C D1 E E1 e eA eB L A3 A A2 L A1 0 - 15 C e B1 B eA eB D1 Plastic DIP PLASTIC DUAL-IN-LINE PACKAGE (0.300 in.) INCHES MAX MIN 0.200 - - 0.015 0.175 0.125 0.080 0.055 0.022 0.016 0.065 0.045 0.012 0.008 0.080 0.005 0.325 0.300 0.310 0.240 - 0.100 - 0.300 0.400 - 0.150 0.115 PKG. DIM PINS P P P P P N D D D D D D 8 14 16 18 20 24 INCHES MIN MAX 0.348 0.390 0.735 0.765 0.745 0.765 0.885 0.915 1.015 1.045 1.14 1.265 MILLIMETERS MIN MAX - 5.08 0.38 - 3.18 4.45 1.40 2.03 0.41 0.56 1.14 1.65 0.20 0.30 0.13 2.03 7.62 8.26 6.10 7.87 2.54 - 7.62 - - 10.16 2.92 3.81 MILLIMETERS MIN MAX 8.84 9.91 18.67 19.43 18.92 19.43 22.48 23.24 25.78 26.54 28.96 32.13 21-0043A Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are implied. Maxim reserves the right to change the circuitry and specifications without notice at any time. 8 ___________________Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 (408) 737-7600 (c) 1995 Maxim Integrated Products Printed USA is a registered trademark of Maxim Integrated Products.