QWL - accessories cabling information The Amphenol(R) QWL series of electrical connectors has been designed with the problems of multi-conductor cable users in mind. Two of these problems, namely water proofing and strain relief, are solved by the radial inward compression of an internal neoprene gland in the various cable accessories shown on the following pages. For additional strain relief beyond that provided by the gland, both cable grips and bar clamps are available. Since the glands close down from .094" to .145" (depending on shell size), the optimum condition for cable users is to select a gland with an I.D. only slightly larger than the maximum O.D. of the cable. The inside diameter of the accessory housing determines the maximum diameter of the cable as shown in the tabulation below. Smaller sizes than those shown in each shell size can be accommodated by smaller compression glands. Different cable manufacturers use different constructions and cable lays in manufacturing multi-conductor cable. The specific cabling manufacturing specification should be known by the customer in detail in order to properly figure each QWL application. This knowledge can save many individual wire crossovers in any given run of cable. Crossovers add materially to the cable diameter without a cable accessory. In those cases where diameter buildup is impossible to avoid, special cable accessories with longer barrels are available. How to order information is covered in detail on pages 4 and 5. In selecting the base number below, care should be used, as some of the cable accessories are provided with protection cap attachment rings, while others are provided with the Kellems strain relief grip as shown. If a type or cable accommodation size is not found herein that fulfills your application, please contact Amphenol, Sidney, NY. All dimensions for reference only. Approx. Work Length (Internal) Minimum Housing Inner Diameter Maximum Cable Outer Diameter .250 .359 .359 .375 .484 .484 .750-20 .401 .609 .609 16 .875-20 .500 .734 .734 18 1.000-20 1.120 .859 .859 20 1.125-18 1.370 .984 .984 22 1.250-18 1.370 1.109 1.109 24 1.375-18 1.370 1.234 1.234 28 1.625-18 1.370 5.000 1.427 1.427 32 1.875-16 1.370 6.000 1.708 1.708 36 2.062-16 1.370 5.000 1.895 1.895 40 2.312-16 1.370 6.000 2.130 2.130 44 2.625-16 48 2.875-16 Shell Size QWL Connector Accessory Thd. 10 .500-28 12 .625-24 14 Short 2.218 Long 6.000 41 2.375 2.375 2.630 2.630 QWL - cable accessories 10-101332 Short barrel with grip 10-101335 Short barrel with attachment ring 10-101333 Short barrel without grip 10-130380 Short barrel length with attachment ring & strain relief bars 10-101334 Short barrel with grip & attachment ring 10-113637 Long barrel with attachment ring and grip 42 QWL - accessories 10-130380 cable sealing adapter (with clamp bars) H B F E D LEFT HAND A J G C A SECTION A-A Type I Straight C H B F E D LEFT HAND J G Type II Step Down H B F E D LEFT HAND A J G A C SECTION A-A Type III Step Up 43 QWL - accessories 10-130380 cable sealing adapter (with clamp bars) All dimensions are for reference only. Part Number* Used With Shell Size Cable Range D Thread Class 2B-LH E Free Max F +.010 -.020 G Dia. +.010 -.020 Max. Dia. H Max. J Max. 10-130380-141 14S .812 .750-20UNEF 1.125 1.782 .938 3.229 1.062 10-130380-142 I .938 .750-20UNEF 1.125 2.126 .938 3.573 1.125 III .875 .938 .750-20UNEF 1.125 2.126 .938 3.573 1.125 III 1.000 1.062 .875-20UNEF 1.250 2.282 1.062 3.854 1.375 III 3.854 1.375 III 3.834 1.125 I 1.688 III 4.677 1.562 III 4.104 1.125 II 4.776 1.688 III 1.188 4.607 1.812 III 1.188 4.365 1.375 I 2.933 1.312 4.677 1.562 I 1.250 2.631 1.312 4.365 1.375 II 1.125-18UNEF 1.250 2.996 1.312 4.740 1.688 III 1.125-18UNEF 1.250 2.933 1.312 4.677 1.562 I 1.250 1.125-18UNEF 1.250 3.062 1.312 4.807 1.812 III 1.062 1.125 1.125-18UNEF 1.250 2.933 1.312 4.677 1.562 I 1.312 1.250 1.125-18UNEF 1.250 3.063 1.312 4.807 1.812 III .696 1.062 1.250 1.250-18UNEF 1.250 2.933 1.438 4.677 1.562 II .626 1.062 1.250 1.250-18UNEF 1.250 2.933 1.438 4.677 1.562 II 1.130 1.005 1.780 1.375 1.250-18UNEF 1.500 3.266 1.438 5.250 2.469 III 22 .680 .567 1.312 1.375 1.250-18UNEF 1.250 3.059 1.438 4.803 1.812 III 24 .900 .787 1.312 1.375 1.375-18UNEF 1.250 3.059 1.562 4.803 1.812 I 10-130380-243 24 1.180 1.055 1.780 1.812 1.375-18UNEF 1.500 3.204 1.562 5.198 2.469 III 10-130380-244 24 .680 .567 1.312 1.375 1.375-18UNEF 1.250 3.059 1.562 4.803 1.812 I 10-130380-245 24 .630 .517 1.312 1.375 1.375-18UNEF 1.250 3.059 1.562 4.803 1.812 I 10-130380-246 24 1.000 .875 1.546 1.625 1.375-18UNEF 1.500 3.121 1.562 5.115 2.125 III 10-130380-247 24 .805 .692 1.312 1.375 1.375-18UNEF 1.250 3.059 1.562 4.803 1.812 I 10-130380-281 28 1.310 1.185 1.780 1.875 1.625-18UNEF 1.500 3.184 1.812 5.178 2.469 III 10-130380-282 28 .970 .857 1.312 1.625 1.625-18UNEF 1.250 3.059 1.812 4.803 1.812 II 10-130380-283 28 .880 .755 1.546 1.625 1.625-18UNEF 1.500 3.121 1.812 5.115 2.125 I 10-130380-284 28 1.427 1.320 2.000 1.875 1.625-18UNEF 1.500 3.184 1.812 5.178 2.625 III 10-130380-321 32 .970 .875 1.312 1.875 1.875-16UN 1.250 3.059 2.062 4.803 1.812 II 10-130380-322 32 1.230 1.105 1.780 1.875 1.875-16UN 1.500 3.184 2.062 5.178 2.469 I 10-130380-323 32 1.328 1.240 1.780 1.875 1.875-16UN 1.500 3.184 2.062 5.178 2.469 I 10-130380-324 32 .750 .637 1.312 1.875 1.875-16UN 1.250 3.059 2.062 4.803 1.812 II 10-130380-325 32 1.055 .958 1.546 1.875 1.875-16UN 1.500 3.121 2.062 5.115 2.125 II 10-130380-326 32 1.375 1.250 2.000 2.062 1.875-16UN 1.500 3.246 2.062 5.240 2.625 III 10-130380-361 36 1.310 1.185 1.780 2.062 2.0625-16UN 1.500 3.184 2.312 5.178 2.469 II 10-130380-362 36 1.900 1.775 2.438 2.312 2.0625-16UN 1.625 3.500 2.312 5.619 3.171 III 10-130380-363 36 1.530 1.406 2.000 2.062 2.0625-16UN 1.500 3.246 2.312 5.240 2.625 I 10-130380-364 36 1.445 1.320 2.000 2.062 2.0625-16UN 1.500 3.246 2.312 5.240 2.625 I 10-130380-365 36 .805 .692 1.312 2.062 2.0625-16UN 1.250 3.059 2.312 4.803 1.812 II 10-130380-366 36 .603 .511 1.000 2.000 2.0625-16UN 1.250 2.875 2.312 4.619 1.375 II 10-130380-367 36 1.000 .875 1.546 2.062 2.0625-16UN 1.500 3.121 2.312 5.115 2.125 II 10-130380-401 40 1.730 1.605 2.438 2.500 2.3125-16UN 1.625 3.469 2.562 5.588 3.171 III 10-130380-402 40 1.310 1.185 1.780 2.312 2.3125-16UN 1.500 3.184 2.562 5.178 2.469 II 10-130380-403 40 1.180 1.055 1.780 2.312 2.3125-16UN 1.500 3.184 2.562 5.178 2.469 II 10-130380-404 40 1.109 .984 1.546 2.312 2.3125-16UN 1.500 3.121 2.562 5.115 2.125 II 10-130380-441 44 1.900 1.775 2.438 2.750 2.625-16UN 1.625 4.281 2.875 6.588 3.171 II Min. Dia. B +.000 -.010 C +.010 -.000 .460 .366 .750 14S .438 .344 .875 10-130380-143 14S .375 .306 10-130380-161 16S .530 .436 10-130380-162 16S .605 .511 1.000 1.062 .875-20UNEF 1.250 2.282 1.062 10-130380-171 16 .500 .406 .875 .938 .875-20UNEF 1.125 2.215 1.062 10-130380-181 18 .828 .715 1.188 1.250 1.000-20UNEF 1.250 3.032 1.188 4.776 10-130380-182 18 .699 .605 1.062 1.125 1.000-20UNEF 1.250 2.933 1.188 10-130380-183 18 .500 .406 .875 1.094 1.000-20UNEF 1.125 2.485 1.188 10-130380-184 18 .562 .449 1.188 1.250 1.000-20UNEF 1.250 3.032 1.188 10-130380-185 18 .750 .637 1.312 1.000 1.000-20UNEF 1.250 3.063 10-130380-186 18 .530 .436 1.000 1.062 1.000-20UNEF 1.250 2.621 10-130380-201 20 .625 .531 1.062 1.125 1.125-18UNEF 1.250 10-130380-202 20 .605 .511 1.000 1.125 1.125-18UNEF 10-130380-203 20 .628 .715 1.188 1.125 10-130380-204 20 .720 .626 1.062 1.125 10-130380-205 20 .900 .787 1.312 10-130380-206 20 .625 .531 10-130380-207 20 .750 .637 10-130380-221 22 .790 10-130380-222 22 .720 10-130380-223 22 10-130380-224 10-130380-242 *For complete order number see pages 4 and 5. 44 Type QWL - accessories 10-10133X cable sealing adapter H E B F K* OPTIONAL D LEFT HAND A G C A SECTION A-A Type I Straight H C B K* OPTIONAL E F D LEFT HAND G Type II Step Down H B K* OPTIONAL E F D LEFT HAND A G A *Wire grip dimensions (K) apply to 10-101332 and 10-101334 assemblies only. 45 C SECTION A-A Type III Step Up QWL - accessories 10-10133X cable sealing adapter All dimensions are for reference only. Used With Shell Size Max. Dia. Min. Dia. B +.000 -.010 C +.010 -.000 D Thread Class 2B-LH E Free Max. F +.010 -.020 G Dia. +.010 -.020 H .045 K Free Approx. 10-10133X-121 12S .281 .219 .750 .812 .6250-24NEF .500 1.938 .812 2.750 2.844 III 10-10133X-122 12S .500 .406 1.062 1.000 .6250-24NEF .562 2.875 .812 3.750 4.688 III 10-10133X-123 12S .405 .316 1.000 .812 .6250-24NEF .562 2.548 .812 3.422 3.688 III 10-10133X-141 14S .337 .281 .750 .812 .7500-20UNEF .500 1.782 .938 2.594 3.344 I 10-10133X-142 14S .222 .160 .625 .812 .7500-20UNEF .562 1.782 .938 2.532 2.406 II 10-10133X-143 14S .281 .219 .750 .812 .7500-20UNEF .500 1.782 .938 2.594 2.844 I 10-10133X-144 14S .530 .441 1.000 .812 .7500-20UNEF .562 2.719 .938 3.594 4.688 III Part Number* Cable Range Type 10-10133X-145 14S .463 .406 .875 .938 .7500-20UNEF .500 2.126 .938 2.938 4.344 III 10-10133X-146 14S .405 .316 1.000 .812 .7500-20UNEF .562 2.719 .938 3.594 3.688 III 10-10133X-151 14 .405 .316 1.000 .812 .7500-20UNEF .562 2.719 .938 3.765 3.688 III 10-10133X-161 16S .463 .406 .875 .938 .8750-20UNEF .500 1.844 1.062 2.656 4.344 I 10-10133X-162 16S .589 .511 1.000 1.062 .8750-20UNEF .562 2.282 1.062 3.156 5.188 III 10-10133X-163 16S .625 .580 1.062 1.125 .8750-20UNEF .562 2.933 1.062 3.807 6.188 III 10-10133X-164 16S .405 .316 1.000 1.062 .8750-20UNEF .562 2.282 1.062 3.156 3.688 III 10-10133X-165 16S .530 .441 1.000 1.062 .8750-20UNEF .562 2.282 1.062 3.156 4.688 III 10-10133X-166 16S .699 .605 1.062 1.125 .8750-20UNEF .562 2.933 1.062 3.807 6.188 III 10-10133X-167 16S .281 .219 .750 .938 .8750-20UNEF .500 1.844 1.062 2.656 2.844 II 10-10133X-171 16 .589 .511 1.000 1.062 .8750-20UNEF .562 2.621 1.062 3.667 5.188 III 10-10133X-172 16 .438 .400 .875 .938 .8750-20UNEF .500 2.215 1.062 3.199 4.344 I 10-10133X-173 16 .625 .580 1.062 1.125 .8750-20UNEF .562 2.933 1.062 3.979 6.188 III 10-10133X-174 16 .530 .441 1.000 1.062 .8750-20UNEF .562 2.621 1.062 3.667 4.688 III 10-10133X-175 16 .405 .316 1.000 1.062 .8750-20UNEF .562 2.621 1.062 3.667 3.688 III 10-10133X-181 18 .589 .511 1.000 1.062 1.0000-20UNEF .562 2.621 1.188 3.667 5.188 I 10-10133X-182 18 .625 .580 1.062 1.125 1.0000-20UNEF .562 2.933 1.188 3.979 6.188 III 10-10133X-183 18 .530 .441 1.000 1.062 1.0000-20UNEF .562 2.621 1.188 3.667 4.688 I 10-10133X-184 18 .699 .605 1.062 1.125 1.0000-20UNEF .562 2.933 1.188 3.979 6.188 III 10-10133X-185 18 .405 .316 1.000 1.062 1.0000-20UNEF .562 2.621 1.188 3.667 3.688 I 10-10133X-186 18 .455 .361 1.062 1.125 1.0000-20UNEF .562 2.933 1.188 3.979 4.188 III 10-10133X-187 18 .750 .637 1.250 1.000 1.0000-20UNEF .562 3.063 1.188 4.109 6.688 III 10-10133X-188 18 .172 .078 .750 .938 1.0000-20UNEF .500 2.407 1.188 3.391 2.844 II 10-10133X-190 18 .805 .692 1.250 1.000 1.0000-20UNEF .562 3.063 1.188 4.109 6.688 III 10-10133X-201 20 .625 .580 1.062 1.125 1.1250-18NEF .562 2.933 1.312 3.979 6.188 I 10-10133X-202 20 .699 .605 1.062 1.125 1.1250-18NEF .562 2.933 1.312 3.979 6.188 I 10-10133X-203 20 .500 .406 1.062 1.125 1.1250-18NEF .562 2.933 1.312 3.979 4.688 I 10-10133X-204 20 .337 .281 .750 1.125 1.1250-18NEF .500 2.438 1.312 3.422 3.344 II 10-10133X-205 20 .828 .715 1.125 1.250 1.1250-18NEF .547 2.996 1.312 4.042 6.688 III 10-10133X-206 20 .375 .312 .875 1.125 1.1250-18NEF .500 2.469 1.312 3.453 3.844 II 10-10133X-207 20 .281 .219 .750 1.125 1.1250-18NEF .500 2.438 1.312 3.422 2.844 II 10-10133X-208 20 .455 .361 1.062 1.125 1.1250-18NEF .562 2.933 1.312 3.979 4.188 I 10-10133X-209 20 .589 .511 1.000 1.125 1.1250-18NEF .562 2.621 1.312 3.667 5.188 II 10-10133X-210 20 .530 .441 1.000 1.125 1.1250-18NEF .562 2.621 1.312 3.667 4.688 II 10-10133X-211 20 .900 .791 1.250 1.250 1.1250-18NEF .562 3.063 1.312 4.109 7.188 III *For complete order number see pages 4 and 5. 46 QWL - accessories 10-10133X cable sealing adapter All dimensions are for reference only. Part Number* Used With Shell Size Max. Dia. Cable Range Min. Dia. B +.000 -.010 C +.000 -.010 D Thread Class 2B-LH E Free .010 F +.010 -.020 G Dia. +.010 -.020 H .045 K Free Approx. 10-10133X-221 22 .699 .605 1.062 1.250 1.2500-18NEF .562 2.933 1.438 3.979 6.188 II 10-10133X-222 22 .750 .637 1.250 1.375 1.2500-18NEF .562 3.059 1.438 4.105 6.688 III 10-10133X-223 22 .445 .367 1.062 1.250 1.2500-18NEF .562 2.933 1.438 3.979 4.188 II 10-10133X-224 22 1.000 .875 1.500 1.375 1.2500-18NEF .562 3.121 1.438 4.167 7.188 III 10-10133X-225 22 .828 .715 1.125 1.250 1.2500-18NEF .594 2.996 1.438 4.072 6.688 I 10-10133X-226 22 .900 .791 1.250 1.375 1.2500-18NEF .562 3.059 1.438 4.105 7.188 III 10-10133X-227 22 .562 .453 1.125 1.250 1.2500-18NEF .594 2.996 1.438 4.074 5.188 I 10-10133X-228 22 1.101 .984 1.500 1.375 1.2500-18NEF .562 3.121 1.438 4.167 7.688 III 10-10133X-229 22 .589 .511 1.000 1.250 1.2500-18NEF .562 2.750 1.438 3.796 5.188 II 10-10133X-231 22 1.055 .958 1.500 1.375 1.2500-18NEF .562 3.121 1.438 4.167 7.688 III 10-10133X-241 24 1.000 .875 1.500 1.625 1.3750-18NEF .562 3.121 1.562 4.167 7.188 III 10-10133X-242 24 .562 .453 1.125 1.406 1.3750-18NEF .562 2.996 1.562 4.042 5.188 II 10-10133X-243 24 .750 .637 1.250 1.375 1.3750-18NEF .562 3.059 1.562 4.105 6.688 I 10-10133X-244 24 .900 .791 1.250 1.375 1.3750-18NEF .562 3.059 1.562 4.105 7.188 I 10-10133X-245 24 1.101 .984 1.500 1.625 1.3750-18NEF .562 3.121 1.562 4.167 7.688 III 10-10133X-246 24 .405 .316 1.000 1.375 1.3750-18NEF .562 2.750 1.562 3.796 3.688 II 10-10133X-247 24 .828 .715 1.125 1.406 1.3750-18NEF .562 2.996 1.562 4.042 6.688 II 10-10133X-248 24 .805 .692 1.250 1.375 1.3750-18NEF .562 3.059 1.562 4.105 6.688 I 10-10133X-249 24 1.130 1.005 1.750 1.812 1.3750-18NEF .562 3.204 1.562 4.250 7.188 III 10-10133X-281 28 1.055 .958 1.500 1.625 1.6250-18NEF .562 3.121 1.812 4.167 7.688 I 10-10133X-282 28 .900 .791 1.250 1.625 1.6250-18NEF .562 3.059 1.812 4.105 7.188 II 10-10133X-283 28 1.000 .875 1.500 1.625 1.6250-18NEF .562 3.121 1.812 4.167 7.188 I 10-10133X-284 28 .630 .535 1.250 1.625 1.6250-18NEF .562 3.059 1.812 4.105 5.688 II 10-10133X-285 28 .750 .637 1.250 1.625 1.6250-18NEF .562 3.059 1.812 4.105 6.688 II 10-10133X-286 28 1.180 1.099 1.750 1.875 1.6250-18NEF .562 3.184 1.812 4.230 8.188 III 10-10133X-287 28 1.101 .984 1.500 1.625 1.6250-18NEF .562 3.121 1.812 4.167 7.688 I 10-10133X-288 28 1.310 1.200 1.750 1.875 1.6250-18NEF .562 3.184 1.812 4.230 8.688 III 10-10133X-289 28 1.230 1.105 1.750 1.875 1.6250-18NEF .562 3.184 1.812 4.230 8.188 III 10-10133X-290 28 .880 .755 1.500 1.625 1.6250-18NEF .562 3.121 1.812 4.167 6.688 I 10-10133X-291 28 .957 .857 1.250 1.625 1.6250-18NEF .547 3.059 1.812 4.090 7.188 II 10-10133X-292 28 .828 .715 1.125 1.625 1.6250-18NEF .562 2.954 1.812 4.000 6.688 II 10-10133X-293 28 1.375 1.250 2.000 1.875 1.6250-18NEF .562 3.184 1.812 4.230 9.688 III 10-10133X-294 28 1.445 1.320 2.000 1.875 1.6250-18NEF .562 3.184 1.812 4.230 9.688 III 10-10133X-295 28 .805 .692 1.250 1.625 1.6250-18NEF .562 3.059 1.812 4.105 6.688 II 10-10133X-321 32 .880 .755 1.500 1.875 1.8750-16N .562 3.121 2.062 4.167 6.688 II 10-10133X-322 32 1.101 .984 1.500 1.875 1.8750-16N .562 3.121 2.062 4.167 7.688 II 10-10133X-323 32 .750 .637 1.250 1.875 1.8750-16N .562 3.059 2.062 4.105 6.688 II 10-10133X-324 32 1.445 1.320 2.000 2.062 1.8750-16N .672 3.246 2.062 4.292 9.688 III 10-10133X-325 32 1.180 1.099 1.750 1.875 1.8750-16N .562 3.184 2.062 4.230 8.188 I 10-10133X-326 32 .375 .312 .875 1.875 1.8750-16N .500 2.766 2.062 3.750 3.844 II 10-10133X-327 32 .957 .857 1.250 1.875 1.8750-16N .562 3.059 2.062 4.105 7.188 II 10-10133X-328 32 1.230 1.105 1.750 1.875 1.8750-16N .562 3.184 2.062 4.230 8.188 I 10-10133X-329 32 1.530 1.406 2.000 2.062 1.8750-16N .562 3.246 2.062 4.292 10.688 III 10-10133X-330 32 1.000 .875 1.500 1.875 1.8750-16N .562 3.121 2.062 4.167 7.188 II 10-10133X-331 32 1.375 1.250 2.000 2.062 1.8750-16N .562 3.246 2.062 4.292 9.688 III 10-10133X-332 32 1.750 1.875 1.8750-16N .562 3.184 2.062 4.230 8.688 I 32 (Oval) 1.500 1.875 1.8750-16N .562 3.121 2.062 4.167 6.688 II 10-10133X-334 32 1.310 .580 x .825 .500 x .705 1.200 10-10133X-333 (Oval) 1.500 1.875 1.8750-16N .562 3.121 2.062 4.167 6.688 II *For complete order number see pages 4 and 5. 47 Type QWL - accessories 10-10133X cable sealing adapter All dimensions are for reference only. Part Number* Used With Shell Size Max. Dia. Cable Range Min. Dia. B +.000 -.010 C +.000 -.010 D Thread Class 2B-LH E Free .035 F +.010 -.020 G Dia. +.010 -.020 H .045 K Free Approx. Type 10-10133X-335 32 .530 .441 1.000 1.625 1.8750-16N .562 2.875 2.062 3.921 4.688 II 10-10133X-336 32 .680 .567 1.250 1.875 1.8750-16N .562 3.059 2.062 4.105 6.688 II 10-10133X-337 32 .463 .406 .875 1.875 1.8750-16N .500 2.766 2.062 3.750 4.344 II 10-10133X-361 36 1.055 .958 1.500 2.062 2.0625-16N .562 3.121 2.312 4.167 7.688 II 10-10133X-362 36 1.445 1.320 2.000 2.062 2.0625-16N .562 3.246 2.312 4.292 9.688 I 10-10133X-363 36 1.530 1.406 2.000 2.062 2.0625-16N .562 3.246 2.312 4.292 10.688 I 10-10133X-364 36 1.230 1.105 1.750 2.062 2.0625-16N .562 3.184 2.312 4.230 8.188 II 10-10133X-365 36 .750 .637 1.250 2.062 2.0625-16N .562 3.059 2.312 4.105 6.688 II 10-10133X-366 36 .880 .755 1.500 2.062 2.0625-16N .562 3.121 2.312 4.167 6.688 II 10-10133X-367 36 1.656 1.531 2.250 2.312 2.0625-16N .562 3.308 2.312 4.354 12.688 III 10-10133X-368 36 1.101 .984 1.500 2.062 2.0625-16N .562 3.121 2.312 4.167 7.688 II 10-10133X-369 36 .957 .857 1.250 2.062 2.0625-16N .672 3.059 2.312 4.090 7.188 II 10-10133X-370 36 1.900 1.775 2.438 2.312 2.0625-16N .500 3.500 2.312 4.656 13.688 III 10-10133X-371 36 .375 .312 .875 2.062 2.0625-16N .500 2.813 2.312 3.797 3.844 II 10-10133X-372 36 1.825 1.700 2.438 2.312 2.0625-16N .672 3.500 2.312 4.656 13.688 III 10-10133X-373 36 1.375 1.250 2.000 2.062 2.0625-16N .562 3.246 2.312 4.292 9.688 I 10-10133X-374 36 1.562 1.437 2.250 2.312 2.0625-16N .562 3.308 2.312 4.354 11.188 III 10-10133X-375 36 1.730 1.605 2.438 2.312 2.0625-16N .672 3.500 2.312 4.656 13.688 III 10-10133X-376 36 .530 .441 1.000 1.875 2.0625-16N .562 2.875 2.312 3.921 4.688 II 10-10133X-377 36 1.130 1.005 1.750 2.062 2.0625-16N .562 3.184 2.312 4.230 7.188 II 10-10133X-378 36 1.180 1.055 1.750 2.062 2.0625-16N .562 3.184 2.312 4.230 8.188 II 10-10133X-379 36 1.595 1.470 2.250 2.312 2.0625-16N .562 3.308 2.312 4.354 11.688 III 10-10133X-401 40 1.310 1.200 1.750 2.312 2.3125-16N .562 3.184 2.562 4.230 8.688 II 10-10133X-402 40 1.656 1.531 2.250 2.312 2.3125-16N .562 3.308 2.562 4.354 12.688 I 10-10133X-403 40 1.101 .984 1.500 2.312 2.3125-16N .438 3.121 2.562 4.167 7.688 II 10-10133X-404 40 1.562 1.437 2.250 2.312 2.3125-16N .562 3.308 2.562 4.354 11.188 I 10-10133X-405 40 1.375 1.250 2.000 2.312 2.3125-16N .562 3.246 2.562 4.292 9.688 II 10-10133X-406 40 1.180 1.099 1.750 2.312 2.3125-16N .562 3.184 2.562 4.230 8.188 II 10-10133X-407 40 1.900 1.775 2.438 2.500 2.3125-16N .672 3.469 2.562 4.625 13.688 III 10-10133X-408 40 1.730 1.605 2.438 2.500 2.3125-16N .672 3.469 2.562 4.625 13.688 III 10-10133X-409 40 1.825 1.700 2.438 2.500 2.3125-16N .672 3.469 2.562 4.625 13.688 III 10-10133X-410 40 1.984 1.859 2.438 2.500 2.3125-16N .672 3.469 2.562 4.625 13.688 III 10-10133X-411 40 1.445 1.320 2.000 2.312 2.3125-16N .562 3.246 2.562 4.292 9.688 II 10-10133X-412 40 2.062 1.937 2.750 2.500 2.3125-16N .672 3.500 2.562 4.656 14.188 III 10-10133X-413 40 2.100 1.955 2.750 2.500 2.3125-16N .672 3.500 2.562 4.656 14.188 III 10-10133X-414 40 2.145 2.000 2.750 2.500 2.3125-16N .672 3.500 2.562 4.656 14.188 III 10-10133X-415 40 .957 .857 1.250 2.125 2.3125-16N .562 3.063 2.562 4.109 7.188 II 10-10133X-416 40 1.230 1.103 1.750 2.312 2.3125-16N .562 3.184 2.562 4.230 8.188 II 10-10133X-417 40 1.055 .958 1.500 2.312 2.3125-16N .562 3.121 2.562 4.167 7.688 II 10-10133X-418 40 .630 .567 1.250 2.250 2.3125-16UN .562 3.063 2.562 4.109 6.688 II 10-10133X-441 44 2.170 2.025 2.750 2.625 2.6250-16UN .672 3.609 2.875 4.953 17.188 III 10-10133X-442 44 2.145 2.000 2.750 2.625 2.6250-16UN .672 3.547 2.875 4.891 14.188 III 10-10133X-443 44 2.250 2.105 2.750 2.625 2.6250-16UN .672 3.609 2.875 4.953 17.188 III 10-10133X-445 44 1.130 1.005 1.750 2.625 2.6250-16UN .562 3.969 2.875 5.203 7.188 II 10-10133X-446 44 1.109 .984 1.500 2.500 2.6250-16UN .562 3.905 2.875 5.140 7.688 II 10-10133X-449 44 1.445 1.320 2.000 2.562 2.6250-16UN .562 4.031 2.875 5.265 9.688 II 10-10133X-481 48 1.900 1.775 2.438 2.812 2.8750-16N .562 3.203 3.125 4.547 13.688 II 10-10133X-482 48 2.000 1.867 2.750 2.969 2.8750-16N .672 4.281 3.125 5.625 14.188 II 10-10133X-483 48 2.250 2.105 2.750 2.750 2.8750-16N .672 4.406 3.125 5.750 17.188 I 10-10133X-484 48 2.170 2.025 2.750 2.750 2.8750-16N .672 4.406 3.125 5.750 17.188 I *For complete order number see pages 4 and 5. 48 QWL - accessories 10-113637 cable sealing adapter (with woven strain relief) H E B F K D LEFT HAND A G C A SECTION A-A Type I Straight H C B E F K* Optional D LEFT HAND G Type II Step Down H E B K* Optional F D LEFT HAND A G A C SECTION A-A Type III Step Up 49 QWL - accessories 10-113637 cable sealing adapter (with woven strain relief) All dimensions are for reference only. Part Number* Used With Shell Size Max. Dia. Cable Range Min. Dia. B +.000 -.010 C +.010 -.000 E Free .035 F +.010 -.020 G Dia. +.010 -.020 H .045 K Free Approx. 10-113637-141 14S .337 .281 .750 .750 .7500-20UNEF .500 5.282 .938 6.094 3.344 10-113637-142 14S .405 .316 1.000 I 1.000 .7500-20UNEF .562 5.500 .938 6.374 3.688 III 10-113637-143 14S .530 .441 10-113637-144 14S .463 .406 1.000 1.000 .7500-20UNEF .562 5.500 .938 6.374 4.688 III .875 .938 .7500-20UNEF .500 5.344 .938 6.156 4.344 10-113637-171 16 .699 III .605 1.062 1.125 .8750-20UNEF .562 5.563 1.062 6.609 6.188 III 10-113637-172 16 10-113637-181 18 .530 .441 1.000 1.000 .8750-20UNEF .562 5.500 1.062 6.546 4.688 III .828 .715 1.125 1.250 1.0000-20UNEF .562 6.657 1.188 7.703 6.688 10-113637-201 III 20 .750 .637 1.250 1.312 1.1250-18NEF .562 6.000 1.312 7.046 6.688 III 10-113637-202 20 .984 .875 1.500 1.625 1.1250-18NEF .562 6.750 1.312 7.796 7.188 III 10-113637-203 20 .900 .791 1.250 1.312 1.1250-18UNEF .562 6.000 1.312 7.046 7.188 III 10-113637-221 22 .750 .637 1.250 1.312 1.2500-18NEF .562 6.000 1.438 7.046 6.688 III 10-113637-222 22 .699 .605 1.062 1.312 1.2500-18NEF .562 5.063 1.438 6.109 6.188 II 10-113637-223 22 1.055 .958 1.500 1.625 1.2500-18NEF .562 6.750 1.438 7.796 7.688 III 10-113637-224 22 1.828 .715 1.125 1.250 1.2500-18NEF .562 5.625 1.438 6.671 6.688 I 10-113637-225 22 .589 .511 1.000 1.250 1.2500-18NEF .562 5.500 1.438 6.546 5.188 II 10-113637-241 24 .957 .857 1.250 1.375 1.3750-18NEF .562 6.000 1.562 7.046 7.188 I 10-113637-242 24 .750 .637 1.250 1.375 1.3750-18NEF .562 6.000 1.562 7.046 6.688 I 10-113637-243 24 1.101 .984 1.500 1.625 1.3750-18NEF .562 6.750 1.562 7.796 7.688 III 10-113637-244 24 1.000 .875 1.500 1.625 1.3750-18NEF .562 6.750 1.562 7.796 7.188 III 10-113637-245 24 1.180 1.055 1.750 1.812 1.3750-18NEF .562 6.813 1.562 7.859 8.188 III 10-113637-246 24 .805 .692 1.250 1.375 1.3750-18NEF .562 6.000 1.562 7.046 6.688 I 10-113637-281 28 1.000 .875 1.500 1.562 1.6250-18NEF .562 6.750 1.812 7.796 7.188 I 10-113637-282 28 1.900 1.775 2.438 2.438 1.6250-18NEF .672 8.125 1.812 9.281 13.688 III 10-113637-283 28 1.375 1.250 2.000 2.000 1.6250-18NEF .562 6.875 1.812 7.921 9.688 III 10-113637-284 28 .750 .637 1.250 1.562 1.6250-18NEF .562 5.750 1.812 6.796 6.688 II 10-113637-285 28 1.101 .984 1.500 1.562 1.6250-18NEF .562 6.750 1.812 7.796 7.688 I 10-113637-286 28 1.130 1.005 1.750 1.875 1.6250-18NEF .562 6.813 1.812 7.859 7.188 III 10-113637-287 28 .900 .791 1.250 1.562 1.6250-18NEF .562 5.750 1.812 6.796 7.188 II 10-113637-288 28 1.427 1.320 2.000 2.000 1.6250-18NEF .562 6.875 1.812 7.921 9.688 III 10-113637-289 28 1.180 1.099 1.750 1.875 1.6250-18NEF .562 6.812 1.812 7.858 8.188 III 10-113637-290 28 1.055 .958 1.500 1.562 1.6250-18NEF .562 6.750 1.812 7.796 7.688 I 10-113637-291 28 .957 .857 1.250 1.562 1.6250-18NEF .562 5.750 1.812 6.796 7.188 II 10-113637-292 28 1.310 1.200 1.750 1.875 1.6250-18NEF .562 6.813 1.812 7.859 8.688 III 10-113637-293 28 .530 .441 1.000 1.625 1.6250-18NEF .562 6.500 1.812 7.546 4.688 II 10-113637-294 28 1.230 1.105 1.750 1.875 1.6250-18NEF .562 6.813 1.812 7.859 8.188 III 10-113637-295 28 .630 .535 1.250 1.562 1.6250-18NEF .562 5.750 1.812 6.796 5.688 II D Thread Class 2B-LH *For complete order number see pages 4 and 5. 50 Type QWL - accessories 10-113637 cable sealing adapter (with woven strain relief) All dimensions are for reference only. Part Number* Used With Shell Size Max. Dia. Cable Range Min. Dia. B +.000 -.010 C +.010 -.000 D Thread Class 2B-LH E Free .035 F +.010 -.020 G Dia. +.010 -.020 H .045 K Free Approx. Type 10-113637-321 32 .828 .715 1.125 1.844 1.8750-16N .594 7.625 2.062 8.703 6.688 II 10-113637-322 32 1.310 1.200 1.750 1.812 1.8750-16UN .562 6.812 2.062 7.858 8.688 I 10-113637-323 32 1.130 1.005 1.750 1.812 1.8750-16UN .562 6.812 2.062 7.858 7.188 I 10-113637-324 32 1.375 1.250 2.000 2.000 1.8750-16UN .562 7.875 2.062 8.921 9.688 III 10-113637-325 32 1.445 1.320 2.000 2.000 1.8750-16UN .562 7.875 2.062 8.921 9.688 III 10-113637-326 32 1.180 1.099 1.750 1.812 1.8750-16UN .562 6.812 2.062 7.858 8.188 I 10-113637-327 32 1.656 1.531 2.250 2.250 1.8750-16UN .562 7.141 2.062 8.187 12.688 III II 10-113637-328 32 .970 .857 1.250 1.844 1.8750-16UN .562 6.688 2.062 7.734 7.188 10-113637-361 36 1.375 1.250 2.000 2.000 2.0625-16N .562 6.875 2.312 7.921 9.688 I 10-113637-362 36 1.000 .875 1.500 2.000 2.0625-16N .562 6.750 2.312 7.796 7.188 II 10-113637-363 36 1.920 x 1.140 oval 1.920 x 1.140 oval 2.438 2.438 2.0625-16N .672 8.125 2.312 9.281 13.688 III 10-113637-364 36 1.230 1.105 1.750 2.000 2.0625-16N .562 6.813 2.312 7.859 8.188 II 10-113637-365 36 1.562 1.437 2.250 2.250 2.0625-16N .562 6.938 2.312 7.984 11.188 III 10-113637-366 36 1.656 1.531 2.250 2.250 2.0625-16N .562 6.938 2.312 7.984 11.188 III 10-113637-367 36 1.445 1.320 2.000 2.000 2.0625-16N .562 6.875 2.312 7.921 9.688 I 10-113637-368 36 1.825 1.700 2.438 2.500 2.0625-16N .672 9.125 2.312 9.281 13.688 III 10-113637-369 36 1.895 1.775 2.438 2.438 2.0625-16N .672 8.125 2.312 9.281 13.688 III 10-113637-370 36 1.730 1.605 2.438 2.438 2.0625-16N .672 8.125 2.312 9.281 13.688 III 10-113637-371 36 1.310 1.200 1.750 2.000 2.0625-16N .562 6.813 2.312 7.859 8.688 II 10-113637-401 40 1.906 1.761 2.750 2.438 2.3125-16N .672 8.125 2.562 9.281 14.188 III 10-113637-402 40 1.940 1.815 2.438 2.438 2.3125-16N .672 8.125 2.562 9.281 13.688 III 10-113637-403 40 1.900 1.775 2.438 2.438 2.3125-16N .672 8.125 2.562 9.281 13.688 III 10-113637-404 40 1.825 1.700 2.438 2.438 2.3125-16N .672 8.125 2.562 9.281 13.688 III 10-113637-405 40 1.310 1.200 1.750 2.250 2.3125-16N .562 7.813 2.562 8.859 8.688 II 10-113637-406 40 1.180 1.099 1.750 2.250 2.3125-16N .562 7.813 2.562 8.859 8.188 II 10-113637-407 40 1.230 1.105 1.750 2.250 2.3125-16N .562 7.813 2.562 8.859 8.188 II 10-113637-408 40 1.656 1.531 2.250 2.250 2.3125-16N .562 7.938 2.562 8.984 11.188 I 10-113637-410 40 2.145 2.000 2.750 2.438 2.3125-16N .672 8.125 2.562 9.281 14.188 III 10-113637-411 40 1.984 1.859 2.438 2.438 2.3125-16N .672 8.125 2.562 9.281 13.688 III 10-113637-412 40 1.940 1.815 2.438 2.438 2.3125-16N .672 11.125 2.562 12.281 13.688 III 10-113637-413 40 1.984 1.859 2.438 2.438 2.3125-16N .672 11.125 2.562 12.281 13.688 III 10-113637-414 40 2.100 1.955 2.750 2.625 2.3125-16N .672 12.000 2.562 13.156 14.188 III 10-113637-415 40 1.562 1.437 2.250 2.250 2.3125-16N .562 7.938 2.562 8.984 11.188 I 10-113637-416 40 1.445 1.320 2.000 2.312 2.3125-16N .562 6.875 2.562 7.921 9.688 II 10-113637-417 40 1.375 1.250 2.000 2.312 2.3125-16N .562 6.875 2.562 7.921 9.688 II *For complete order number see pages 4 and 5. 51 QWL - accessories 10-113637 cable sealing adapter (with woven strain relief) All dimensions are for reference only. Part Number* Used With Shell Size Max Dia Cable Range Min Dia B +.000 -.010 C +.010 -.000 D Thread Class 2B-LH E Free .035 F +.010 -.020 G Dia +.010 -.020 H .045 K Free Approx. Type 10-113637-441 44 2.100 1.955 2.750 2.750 2.6250-16UN .672 8.125 2.875 9.469 14.188 III 10-113637-442 44 2.250 2.105 2.750 2.875 2.6250-16UN .672 8.188 2.875 9.531 17.188 III 10-113637-443 44 2.000 1.867 2.750 2.750 2.6250-16UN .672 8.125 2.875 9.469 14.188 III 10-113637-444 44 1.500 1.375 2.250 2.500 2.6250-16UN .562 7.938 2.875 9.171 11.188 II 10-113637-445 44 1.730 1.605 2.438 2.750 2.6250-16UN .672 8.125 2.875 9.469 13.688 II 10-113637-446 44 .750 .637 1.250 2.625 2.6250-16UN .562 6.688 2.875 7.921 6.688 II 10-113637-447 44 1.825 1.700 2.438 2.750 2.6250-16UN .672 8.125 2.875 9.469 13.688 II 10-113637-448 44 2.145 2.000 2.750 2.750 2.6250-16UN .672 8.125 2.875 9.469 14.188 III 10-113637-449 44 2.170 2.025 2.750 2.875 2.6250-16UN .672 8.188 2.875 9.532 17.188 III 10-113637-450 44 1.375 1.250 2.000 2.625 2.6250-16UN .562 7.875 2.875 9.109 9.688 II 10-113637-481 48 2.250 2.105 2.750 2.750 2.8750-16N .672 8.188 3.125 9.532 14.688 I 10-113637-482 48 2.500 2.355 2.875 2.875 2.8750-16N .672 8.188 3.125 9.532 18.188 III 10-113637-483 48 2.375 2.230 2.875 2.875 2.8750-16N .672 8.188 3.125 9.532 18.188 III 10-113637-484 48 2.145 2.000 2.750 2.875 2.8750-16N .672 8.125 3.125 9.469 14.188 II 10-113637-485 48 2.000 1.867 2.750 2.875 2.8750-16N .672 8.125 3.125 9.469 14.188 II 10-113637-486 48 1.656 1.531 2.250 2.750 2.8750-16UN .562 7.937 3.125 9.171 12.688 II *For complete order number see pages 4 and 5. 52 QWL - accessories adapter, cable clamp 10-113196-XX adapter L D C V F E A 10-749XX-( ) cable clamp Z W Y This cable clamp is designed to be used with specific QWL insert arrangements. The locations, quantity, and sizes of holes in the clamp grommet must correspond to those in the connector for an effective moisture seal without wire crossing. Contact Amphenol, Sidney, NY, for grommet availability. Example: 10-107618-4P must use 10-74918-4 clamp. 53 QWL - accessories adapter, cable clamp, sealing plugs All dimensions for reference only. D Dia. +.010 -.020 W Min. Thd. Engage Adapter Part Number* Clamp Part Number* 10S 10-113196-10 10-74910-( ) .500-28UNEF .203 .922 .625 .562 1.234 .500-28UNEF .519 .807 .529 12S 10-113196-12 10-74912-( ) .625-24NEF .328 .969 .750 .688 1.281 .625-24NEF .519 .901 .524 12 10-113196-13 10-74913-( ) .625-24NEF .328 .954 .750 .688 1.438 .625-24NEF .519 .901 .524 14S 10-113196-14 10-74914-( ) .750-20UNEF .453 1.094 .875 .812 1.406 .750-20UNEF .519 1.026 .524 14 10-113196-15 10-74915-( ) .750-20UNEF .453 .954 .875 .812 1.438 .750-20UNEF .519 1.026 .524 A Thread Class 2A C +.010 -.000 E Dia. +.010 -.020 Shell Size F .010 L .010 V Thread Class 2B-LH Y Max. Z Max. 16S 10-113196-16 10-74916-( ) .875-20UNEF .578 1.094 1.000 .938 1.406 .875-20UNEF .519 1.119 .524 16 10-113196-17 10-74917-( ) .875-20UNEF .578 1.016 1.000 .938 1.500 .875-20UNEF .519 1.119 .524 18 10-113196-18 10-74918-( ) 1.000-20UNEF .676 1.141 1.188 1.062 1.625 1.000-20UNEF .519 1.229 .556 20 10-113196-20 10-74920-( ) 1.1875-18NEF .801 1.094 1.312 1.250 1.578 1.125-18NEF .505 1.479 .666 22 10-113196-22 10-74922-( ) 1.1875-18NEF .906 1.141 1.438 1.250 1.625 1.250-18NEF .519 1.479 .666 24 10-113196-24 10-74924-( ) 1.4375-18NEF 1.016 1.094 1.562 1.500 1.578 1.375-18NEF .519 1.666 .666 28 10-113196-28 10-74928-( ) 1.4375-18NEF 1.130 1.235 1.812 1.500 1.719 1.625-18NEF .519 1.666 .666 32 10-113196-32 10-74932-( ) 1.7500-18NS 1.438 1.204 2.062 1.875 1.688 1.875-16N .519 2.135 .805 36 10-113196-36 10-74936-( ) 2.000-18NS 1.678 1.266 2.250 2.125 1.750 2.0625-16N .738 2.260 .805 40 10-113196-40 10-74940-( ) 2.2500-16UN 1.914 1.266 2.500 2.375 1.750 2.3125-16N .738 2.510 .805 *For complete order number see page 5. Clamp 10-749XX-( ) has a bright cadmium finish. An olive drab cadmium plate finish is available by order number 71-749XX-( ). To complete clamp order number, add connector insert arrangement number. B DIA C .135 +.030 -.025 A DIA 45 SEALING PLUG MS27488-XX 10-405996-XX Color Code B .005 C .010 A Dia. .010 Order No. Contact Size MS Number Wire Size 10-405996-16 16 27488-16 20-16 Blue .133 .564* .083 10-405996-12 12 27488-12 14-12 Yellow .171 .564* .121 10-405996-8 8 27488-8 10-8 White .315 .470 .185 10-405996-4 4 27488-4 4-6 Blue .415 .470 .310 10-405996-0 0 27488-0 0-2 Yellow .605 1.000 .440 *.020 Sealing plugs are used to fill unused holes in multi-holed grommet configurations 54 QWL - accessories adapter, cable clamp 10-113138-XX adapter L C D V LEFT HAND F E A B M85049/2-( )C cable clamp M Y K 55 A QWL - accessories adapter, cable clamp, sleeve Shell Size 12 14 16 18 Adapter Part Number* Clamp MS Part Number* A Thread Class 2A (Plated) B Min Full Thd C Dia +.000 -.010 D .020 E Dia +.010 -.020 F .010 10-113138-12 M85049/2-4C .625-24UNEF 10-113138-13 M85049/2-4C .625-24NEF .422 .386 1.078 .750 .688 .422 .386 1.125 .750 .688 10-113138-14 M85049/2-6C 10-113138-15 M85049/2-6C .750-20UNEF .422 .500 1.078 .875 .812 .750-20UNEF .422 .500 1.125 .875 .812 10-113138-16 10-113138-17 M85049/2-8C .875-20UNEF .422 .625 1.078 1.000 .938 M85049/2-8C .875-20UNEF .422 .625 1.125 1.000 .938 10-113138-18 M85049/2-10C 1.000-20UNEF .422 .752 1.125 1.188 1.062 K Dia Cable Range Free Closed .302 .094 .428 .230 .515 .316 .614 .378 L Max V Thread Class 2B-LH M Max 1.390 1.609 1.390 1.609 1.390 1.609 1.609 1.375 1.375 1.375 1.437 .625-24NEF .625-24NEF .750-20UNEF .750-20UNEF .875-20UNEF .875-20UNEF 1.000-20UNEF Y Max .906 1.031 1.125 1.234 20 10-113138-20 M85049/2-12C 1.1875-18UNEF .422 .891 1.125 1.312 1.250 .738 .445 1.609 1.437 1.125-18NEF 1.484 22 10-113138-22 M85049/2-12C 1.1875-18NEF .422 .891 1.125 1.438 1.250 .738 .445 1.609 1.437 1.250-18NEF 1.484 24 10-113138-24 M85049/2-16C 1.4375-18UNEF .422 1.111 1.125 1.562 1.500 .926 .611 1.609 1.562 1.375-18NEF 1.671 28 10-113138-28 M85049/2-16C 1.4375-18NEF .422 1.111 1.297 1.812 1.500 .926 .611 1.781 1.562 1.625-18NEF 1.671 32 10-113138-32 M85049/2-20C 1.750-18UNS .484 1.422 1.297 2.062 1.875 1.200 .922 1.781 1.812 1.875-16UN 2.188 36 10-113138-36 M85049/2-24C 2.000-18UNS .562 1.672 1.297 2.250 2.125 1.363 .922 1.781 2.062 2.0625-16N 2.344 40 10-113138-40 M85049/2-28C 2.250-16UN .562 1.914 1.297 2.500 2.375 1.611 1.180 1.781 2.062 2.3125-16N 2.594 44 10-113138-44 M85049/2-32C 2.500-16UN .562 2.142 1.297 2.812 2.625 1.865 1.427 1.781 2.188 2.625-16UN 2.812 MS3420-( sleeve )A 2.000 .031 Z Dia Shell Size Sleeve MS Part Number D Dia. .016 Free .016 Closed 12 MS3420-4A .302 .219 .010 14 MS3420-4A MS3420-6A .302 .427 .219 .312 .020 .114 16 MS3420-6A MS3420-8A .427 .531 .312 .438 .085 .220 18 MS3420-6A MS3420-10A .427 .615 .312 .438 .085 .200 20 MS3420-10A MS3420-12A .615 .740 .438 .541 .177 .270 22 MS3420-10A MS3420-12A .615 .740 .438 .541 .177 .270 24 MS3420-8A MS3420-12A MS3420-16A .531 .740 .927 .438 .541 .750 .186 .260 .433 26 MS3420-8A MS3420-12A MS3420-16A .531 .740 .927 .438 .541 .750 .186 .260 .433 32 MS3420-12A MS3420-16A MS3420-20A .740 .927 1.240 .541 .750 .938 .273 .442 .620 36 MS3420-16A MS3420-20A MS3420-24A .927 1.240 1.365 .750 .938 1.125 .358 .504 .682 40 MS3420-16A MS3420-20A MS3420-28A .927 1.240 1.614 .750 .938 1.250 .368 .514 .816 44 MS3420-20A MS3420-28A MS3420-32A 1.240 1.614 1.865 .938 1.250 1.625 .638 .897 1.229 Z D Sleeve not supplied as part of MS3057-( )C assembly. Order separately by part number shown. 56 QWL - accessories protection caps 10-101046-( ), 10-101531-( plug protective covers ) 10-101046 L E F C A 10-101531 B 10-101063-( ), 10-101048-( ) receptacle protective covers 10-101063 E L A D C 10-101048 B 57 QWL - accessories protection caps All dimensions for reference only. A Thread Class 2A B Dia +.010 -.000 C Approx. E Approx. F Flat .010 L Max. 10-101531-10 .6250-0.05P-0.1L-DS .125 3.000 3.375 .500 1.250 10-101531-12 .7500-0.1P-0.2L-DS .125 3.500 3.875 .625 1.438 10-101046-14 10-101531-14 .8750-0.1P-0.2L-DS .125 3.500 3.875 .750 1.438 16 10-101046-16 10-101531-16 1.0000-0.1P-0.2L-DS .140 3.500 3.875 .875 1.438 18 10-101046-18 10-101531-18 1.1250-0.1P-0.2L-DS .140 3.500 4.000 1.000 1.438 20 10-101046-20 10-101531-20 1.2500-0.1P-0.2L-DS .193 4.000 4.500 1.062 1.438 22 10-101046-22 10-101531-22 1.3750-0.1P-0.2L-DS .193 4.000 4.500 1.125 1.438 24 10-101046-24 10-101531-24 1.5000-0.1P-0.2L-DS .193 4.500 5.000 1.250 1.438 28 10-101046-28 10-101531-28 1.7500-0.1P-0.2L-DS .193 4.500 5.000 1.500 1.438 32 10-101046-32 10-101531-32 2.0000-0.1P-0.2L-DS .193 5.000 5.500 1.750 1.438 36 10-101046-36 10-101531-36 2.2500-0.1P-0.2L-DS .193 5.000 5.500 2.000 1.438 40 10-101046-40 10-101531-40 2.5000-0.1P-0.2L-DS .193 5.000 5.500 2.250 1.438 44 10-101046-44 10-101531-44 2.7500-0.1P-0.2L-DS .193 6.000 6.000 2.500 1.438 48 10-101046-48 10-101531-48 3.0000-0.1P-0.2L-DS .193 6.000 6.000 2.750 1.438 B Dia. +.010 -.000 C Approx. D Dia. Max. E Approx. L Max. Shell Size Without Eyelet End Part Number* With Eyelet End Part Number* 10 10-101046-10 12 10-101046-12 14 *For complete order number see page 5. All dimensions for reference only. Shell Size Without Eyelet End Part Number* With Eyelet End Part Number* A Thread Class 2B 10 10-101063-10 10-101048-10 .6250-0.05P-0.1L-DS .140 3.000 .844 3.375 .750 12 10-101063-12 10-101048-12 .7500-0.1P-0.2L-DS .140 3.500 .969 3.875 .750 14 10-101063-14 10-101048-14 .8750-0.1P-0.2L-DS .140 3.500 1.094 3.875 .750 16 10-101063-16 10-101048-16 1.0000-0.1P-0.2L-DS .140 3.500 1.219 3.875 .750 18 10-101063-18 10-101048-18 1.1250-0.1P-0.2L-DS .193 3.500 1.344 4.000 .969 20 10-101063-20 10-101048-20 1.2500-0.1P-0.2L-DS .193 4.000 1.469 4.500 .969 22 10-101063-22 10-101048-22 1.3750-0.1P-0.2L-DS .193 4.000 1.562 4.500 .969 24 10-101063-24 10-101048-24 1.5000-0.1P-0.2L-DS .193 4.500 1.688 5.000 .969 28 10-101063-28 10-101048-28 1.7500-0.1P-0.2L-DS .193 4.500 1.938 5.000 .969 32 10-101063-32 10-101048-32 2.0000-0.1P-0.2L-DS .193 5.000 2.219 5.500 .969 36 10-101063-36 10-101048-36 2.2500-0.1P-0.2L-DS .193 5.000 2.469 5.500 .969 40 10-101063-40 10-101048-40 2.5000-0.1P-0.2L-DS .193 5.000 2.719 5.500 .969 44 10-101063-44 10-101048-44 2.7500-0.1P-0.2L-DS .193 6.000 2.969 6.000 .969 48 10-101063-48 10-101048-48 3.0000-0.1P-0.2L-DS .193 6.000 3.219 6.000 .969 *For complete order number see page 5. 58 QWL - accessories flange gasket, grip banding clamp R (TP) .031 ,010 (10-36675) .031 .005 (10-40450) 10-36675-( ) 10-40450-( ) flange gaskets R (TP) S T 4 HOLES F All dimensions for reference only. Part Number* Part Number* Shell Size F Dia. +.016 -.000 10-36675-10 10-40450-10 10 .625 .719 1.000 .172 10-36675-12 10-40450-12 12 .750 .813 1.094 .172 10-36675-14 10-40450-14 14 .875 .906 1.188 .172 10-36675-16 10-40450-16 16 1.000 .969 1.281 .172 10-36675-18 10-40450-18 18 1.125 1.063 1.375 .203 10-36675-20 10-40450-20 20 1.250 1.156 1.500 .203 10-36675-22 10-40450-22 22 1.375 1.250 1.625 .203 10-36675-24 10-40450-24 24 1.500 1.375 1.750 .203 10-36675-28 10-40450-28 28 1.750 1.563 2.000 .203 10-36675-32 10-40450-32 32 2.000 1.750 2.250 .219 10-36675-36 10-40450-36 36 2.188 1.938 2.500 .219 10-36675-40 10-40450-40 40 2.438 2.188 2.750 .219 10-36675-44 10-40450-44 44 2.688 2.375 3.000 .219 10-36675-48 10-40450-48 48 2.938 2.625 3.250 .219 R .010 S +.016 -.000 T Dia. .010 *For complete order number see page 5. All dimensions for reference only. 10-183249-( ) grip banding clamp .375 REF. A A Dia. Part Number* Max. Min. 10-183249-10 1.125 .812 10-183249-11 1.312 .938 10-183249-12 1.500 1.125 10-183249-13 1.688 1.312 10-183249-14 1.875 1.500 10-183249-15 2.062 1.688 10-183249-16 2.250 1.875 10-183249-17 2.438 2.062 10-183249-18 2.625 2.250 10-183249-19 2.812 2.438 10-183249-20 3.000 2.625 *For complete order number see page 5. 59