41
QWL – accessories
cabling information
The Amphenol® QWL series of electrical connectors has
been designed with the problems of multi-conductor
cable users in mind. Two of these problems, namely
water proofing and strain relief, are solved by the radial
inward compression of an internal neoprene gland in the
various cable accessories shown on the following pages.
For additional strain relief beyond that provided by the
gland, both cable grips and bar clamps are available.
Since the glands close down from .094” to .145”
(depending on shell size), the optimum condition for
cable users is to select a gland with an I.D. only slightly
larger than the maximum O.D. of the cable. The inside
diameter of the accessory housing determines the maxi-
mum diameter of the cable as shown in the tabulation
below. Smaller sizes than those shown in each shell size
can be accommodated by smaller compression glands.
Different cable manufacturers use different constructions
and cable lays in manufacturing multi-conductor cable.
The specific cabling manufacturing specification should
be known by the customer in detail in order to properly
figure each QWL application. This knowledge can save
many individual wire crossovers in any given run of cable.
Crossovers add materially to the cable diameter without a
cable accessory. In those cases where diameter buildup
is impossible to avoid, special cable accessories with
longer barrels are available.
How to order information is covered in detail on pages 4
and 5. In selecting the base number below, care should
be used, as some of the cable accessories are provided
with protection cap attachment rings, while others are
provided with the Kellems strain relief grip as shown. If a
type or cable accommodation size is not found herein
that fulfills your application, please contact Amphenol,
Sidney, NY.
All dimensions for reference only.
Shell
Size
QWL Connector
Accessory Thd.
Approx. Work Length (Internal) Minimum Housing
Inner Diameter
Maximum Cable
Outer DiameterShort Long
10 .500-28 .250 .359 .359
12 .625-24 .375 .484 .484
14 .750-20 .401 .609 .609
16 .875-20 .500 .734 .734
18 1.000-20 1.120 .859 .859
20 1.125-18 1.370 .984 .984
22 1.250-18 1.370 1.109 1.109
24 1.375-18 1.370 1.234 1.234
28 1.625-18 1.370 5.000 1.427 1.427
32 1.875-16 1.370 6.000 1.708 1.708
36 2.062-16 1.370 5.000 1.895 1.895
40 2.312-16 1.370 6.000 2.130 2.130
44 2.625-16 2.375 2.375
48 2.875-16 2.218 6.000 2.630 2.630
42
10-101332
Short barrel with grip
10-101333
Short barrel without grip
10-130380
Short barrel length with attachment
ring & strain relief bars
10-101335
Short barrel with attachment ring
10-101335
Short barrel with attachment ring
QWL – cable accessories
10-101334
Short barrel with grip & attachment ring
10-113637
Long barrel with attachment ring and grip
43
Type I Straight
Type II Step Down
Type III Step Up
H
B
D
LEFT HAND
GC
A
F
E
SECTION A-A
J
A
H
B
D
LEFT HAND
G
F
C
E
J
H
B
D
LEFT HAND
GC
A
F
E
SECTION A-A
J
A
QWL – accessories
10-130380
cable sealing adapter (with clamp bars)
44
QWL – accessories
10-130380
cable sealing adapter (with clamp bars)
All dimensions are for reference only.
*For complete order number see pages 4 and 5.
Part
Number*
Used
With
Shell
Size
Cable Range
B
+.000
–.010
C
+.010
–.000
D Thread
Class 2B-LH
E
Free
Max
F
+.010
–.020
G
Dia.
+.010
–.020
H
Max.
J
Max. Type
Max.
Dia.
Min.
Dia.
10-130380-141 14S .460 .366 .750 .812 .750-20UNEF 1.125 1.782 .938 3.229 1.062 I
10-130380-142 14S .438 .344 .875 .938 .750-20UNEF 1.125 2.126 .938 3.573 1.125 III
10-130380-143 14S .375 .306 .875 .938 .750-20UNEF 1.125 2.126 .938 3.573 1.125 III
10-130380-161 16S .530 .436 1.000 1.062 .875-20UNEF 1.250 2.282 1.062 3.854 1.375 III
10-130380-162 16S .605 .511 1.000 1.062 .875-20UNEF 1.250 2.282 1.062 3.854 1.375 III
10-130380-171 16 .500 .406 .875 .938 .875-20UNEF 1.125 2.215 1.062 3.834 1.125 I
10-130380-181 18 .828 .715 1.188 1.250 1.000-20UNEF 1.250 3.032 1.188 4.776 1.688 III
10-130380-182 18 .699 .605 1.062 1.125 1.000-20UNEF 1.250 2.933 1.188 4.677 1.562 III
10-130380-183 18 .500 .406 .875 1.094 1.000-20UNEF 1.125 2.485 1.188 4.104 1.125 II
10-130380-184 18 .562 .449 1.188 1.250 1.000-20UNEF 1.250 3.032 1.188 4.776 1.688 III
10-130380-185 18 .750 .637 1.312 1.000 1.000-20UNEF 1.250 3.063 1.188 4.607 1.812 III
10-130380-186 18 .530 .436 1.000 1.062 1.000-20UNEF 1.250 2.621 1.188 4.365 1.375 I
10-130380-201 20 .625 .531 1.062 1.125 1.125-18UNEF 1.250 2.933 1.312 4.677 1.562 I
10-130380-202 20 .605 .511 1.000 1.125 1.125-18UNEF 1.250 2.631 1.312 4.365 1.375 II
10-130380-203 20 .628 .715 1.188 1.125 1.125-18UNEF 1.250 2.996 1.312 4.740 1.688 III
10-130380-204 20 .720 .626 1.062 1.125 1.125-18UNEF 1.250 2.933 1.312 4.677 1.562 I
10-130380-205 20 .900 .787 1.312 1.250 1.125-18UNEF 1.250 3.062 1.312 4.807 1.812 III
10-130380-206 20 .625 .531 1.062 1.125 1.125-18UNEF 1.250 2.933 1.312 4.677 1.562 I
10-130380-207 20 .750 .637 1.312 1.250 1.125-18UNEF 1.250 3.063 1.312 4.807 1.812 III
10-130380-221 22 .790 .696 1.062 1.250 1.250-18UNEF 1.250 2.933 1.438 4.677 1.562 II
10-130380-222 22 .720 .626 1.062 1.250 1.250-18UNEF 1.250 2.933 1.438 4.677 1.562 II
10-130380-223 22 1.130 1.005 1.780 1.375 1.250-18UNEF 1.500 3.266 1.438 5.250 2.469 III
10-130380-224 22 .680 .567 1.312 1.375 1.250-18UNEF 1.250 3.059 1.438 4.803 1.812 III
10-130380-242 24 .900 .787 1.312 1.375 1.375-18UNEF 1.250 3.059 1.562 4.803 1.812 I
10-130380-243 24 1.180 1.055 1.780 1.812 1.375-18UNEF 1.500 3.204 1.562 5.198 2.469 III
10-130380-244 24 .680 .567 1.312 1.375 1.375-18UNEF 1.250 3.059 1.562 4.803 1.812 I
10-130380-245 24 .630 .517 1.312 1.375 1.375-18UNEF 1.250 3.059 1.562 4.803 1.812 I
10-130380-246 24 1.000 .875 1.546 1.625 1.375-18UNEF 1.500 3.121 1.562 5.115 2.125 III
10-130380-247 24 .805 .692 1.312 1.375 1.375-18UNEF 1.250 3.059 1.562 4.803 1.812 I
10-130380-281 28 1.310 1.185 1.780 1.875 1.625-18UNEF 1.500 3.184 1.812 5.178 2.469 III
10-130380-282 28 .970 .857 1.312 1.625 1.625-18UNEF 1.250 3.059 1.812 4.803 1.812 II
10-130380-283 28 .880 .755 1.546 1.625 1.625-18UNEF 1.500 3.121 1.812 5.115 2.125 I
10-130380-284 28 1.427 1.320 2.000 1.875 1.625-18UNEF 1.500 3.184 1.812 5.178 2.625 III
10-130380-321 32 .970 .875 1.312 1.875 1.875-16UN 1.250 3.059 2.062 4.803 1.812 II
10-130380-322 32 1.230 1.105 1.780 1.875 1.875-16UN 1.500 3.184 2.062 5.178 2.469 I
10-130380-323 32 1.328 1.240 1.780 1.875 1.875-16UN 1.500 3.184 2.062 5.178 2.469 I
10-130380-324 32 .750 .637 1.312 1.875 1.875-16UN 1.250 3.059 2.062 4.803 1.812 II
10-130380-325 32 1.055 .958 1.546 1.875 1.875-16UN 1.500 3.121 2.062 5.115 2.125 II
10-130380-326 32 1.375 1.250 2.000 2.062 1.875-16UN 1.500 3.246 2.062 5.240 2.625 III
10-130380-361 36 1.310 1.185 1.780 2.062 2.0625-16UN 1.500 3.184 2.312 5.178 2.469 II
10-130380-362 36 1.900 1.775 2.438 2.312 2.0625-16UN 1.625 3.500 2.312 5.619 3.171 III
10-130380-363 36 1.530 1.406 2.000 2.062 2.0625-16UN 1.500 3.246 2.312 5.240 2.625 I
10-130380-364 36 1.445 1.320 2.000 2.062 2.0625-16UN 1.500 3.246 2.312 5.240 2.625 I
10-130380-365 36 .805 .692 1.312 2.062 2.0625-16UN 1.250 3.059 2.312 4.803 1.812 II
10-130380-366 36 .603 .511 1.000 2.000 2.0625-16UN 1.250 2.875 2.312 4.619 1.375 II
10-130380-367 36 1.000 .875 1.546 2.062 2.0625-16UN 1.500 3.121 2.312 5.115 2.125 II
10-130380-401 40 1.730 1.605 2.438 2.500 2.3125-16UN 1.625 3.469 2.562 5.588 3.171 III
10-130380-402 40 1.310 1.185 1.780 2.312 2.3125-16UN 1.500 3.184 2.562 5.178 2.469 II
10-130380-403 40 1.180 1.055 1.780 2.312 2.3125-16UN 1.500 3.184 2.562 5.178 2.469 II
10-130380-404 40 1.109 .984 1.546 2.312 2.3125-16UN 1.500 3.121 2.562 5.115 2.125 II
10-130380-441 44 1.900 1.775 2.438 2.750 2.625-16UN 1.625 4.281 2.875 6.588 3.171 II
45
QWL – accessories
10-10133X
cable sealing adapter
Type I Straight
Type II Step Down
Type III Step Up
*Wire grip dimensions (K) apply to 10-101332 and 10-101334 assemblies only.
H
K*
OPTIONAL
BD
LEFT HAND
GC
A
F
E
SECTION A-A
A
H
BD
LEFT HAND
G
F
C
E
K*
OPTIONAL
BD
LEFT HAND
GC
A
F
SECTION A-A
A
H
E
K*
OPTIONAL
46
QWL – accessories
10-10133X
cable sealing adapter
All dimensions are for reference only.
*For complete order number see pages 4 and 5.
Par t
Number*
Used
With
Shell
Size
Cable Range
B
+.000
–.010
C
+.010
–.000
D Thread
Class 2B-LH
E
Free
Max.
F
+.010
–.020
G
Dia.
+.010
–.020
H
±.045
K
Free
Approx. Type
Max.
Dia.
Min.
Dia.
10-10133X-121 12S .281 .219 .750 .812 .6250-24NEF .500 1.938 .812 2.750 2.844 III
10-10133X-122 12S .500 .406 1.062 1.000 .6250-24NEF .562 2.875 .812 3.750 4.688 III
10-10133X-123 12S .405 .316 1.000 .812 .6250-24NEF .562 2.548 .812 3.422 3.688 III
10-10133X-141 14S .337 .281 .750 .812 .7500-20UNEF .500 1.782 .938 2.594 3.344 I
10-10133X-142 14S .222 .160 .625 .812 .7500-20UNEF .562 1.782 .938 2.532 2.406 II
10-10133X-143 14S .281 .219 .750 .812 .7500-20UNEF .500 1.782 .938 2.594 2.844 I
10-10133X-144 14S .530 .441 1.000 .812 .7500-20UNEF .562 2.719 .938 3.594 4.688 III
10-10133X-145 14S .463 .406 .875 .938 .7500-20UNEF .500 2.126 .938 2.938 4.344 III
10-10133X-146 14S .405 .316 1.000 .812 .7500-20UNEF .562 2.719 .938 3.594 3.688 III
10-10133X-151 14 .405 .316 1.000 .812 .7500-20UNEF .562 2.719 .938 3.765 3.688 III
10-10133X-161 16S .463 .406 .875 .938 .8750-20UNEF .500 1.844 1.062 2.656 4.344 I
10-10133X-162 16S .589 .511 1.000 1.062 .8750-20UNEF .562 2.282 1.062 3.156 5.188 III
10-10133X-163 16S .625 .580 1.062 1.125 .8750-20UNEF .562 2.933 1.062 3.807 6.188 III
10-10133X-164 16S .405 .316 1.000 1.062 .8750-20UNEF .562 2.282 1.062 3.156 3.688 III
10-10133X-165 16S .530 .441 1.000 1.062 .8750-20UNEF .562 2.282 1.062 3.156 4.688 III
10-10133X-166 16S .699 .605 1.062 1.125 .8750-20UNEF .562 2.933 1.062 3.807 6.188 III
10-10133X-167 16S .281 .219 .750 .938 .8750-20UNEF .500 1.844 1.062 2.656 2.844 II
10-10133X-171 16 .589 .511 1.000 1.062 .8750-20UNEF .562 2.621 1.062 3.667 5.188 III
10-10133X-172 16 .438 .400 .875 .938 .8750-20UNEF .500 2.215 1.062 3.199 4.344 I
10-10133X-173 16 .625 .580 1.062 1.125 .8750-20UNEF .562 2.933 1.062 3.979 6.188 III
10-10133X-174 16 .530 .441 1.000 1.062 .8750-20UNEF .562 2.621 1.062 3.667 4.688 III
10-10133X-175 16 .405 .316 1.000 1.062 .8750-20UNEF .562 2.621 1.062 3.667 3.688 III
10-10133X-181 18 .589 .511 1.000 1.062 1.0000-20UNEF .562 2.621 1.188 3.667 5.188 I
10-10133X-182 18 .625 .580 1.062 1.125 1.0000-20UNEF .562 2.933 1.188 3.979 6.188 III
10-10133X-183 18 .530 .441 1.000 1.062 1.0000-20UNEF .562 2.621 1.188 3.667 4.688 I
10-10133X-184 18 .699 .605 1.062 1.125 1.0000-20UNEF .562 2.933 1.188 3.979 6.188 III
10-10133X-185 18 .405 .316 1.000 1.062 1.0000-20UNEF .562 2.621 1.188 3.667 3.688 I
10-10133X-186 18 .455 .361 1.062 1.125 1.0000-20UNEF .562 2.933 1.188 3.979 4.188 III
10-10133X-187 18 .750 .637 1.250 1.000 1.0000-20UNEF .562 3.063 1.188 4.109 6.688 III
10-10133X-188 18 .172 .078 .750 .938 1.0000-20UNEF .500 2.407 1.188 3.391 2.844 II
10-10133X-190 18 .805 .692 1.250 1.000 1.0000-20UNEF .562 3.063 1.188 4.109 6.688 III
10-10133X-201 20 .625 .580 1.062 1.125 1.1250-18NEF .562 2.933 1.312 3.979 6.188 I
10-10133X-202 20 .699 .605 1.062 1.125 1.1250-18NEF .562 2.933 1.312 3.979 6.188 I
10-10133X-203 20 .500 .406 1.062 1.125 1.1250-18NEF .562 2.933 1.312 3.979 4.688 I
10-10133X-204 20 .337 .281 .750 1.125 1.1250-18NEF .500 2.438 1.312 3.422 3.344 II
10-10133X-205 20 .828 .715 1.125 1.250 1.1250-18NEF .547 2.996 1.312 4.042 6.688 III
10-10133X-206 20 .375 .312 .875 1.125 1.1250-18NEF .500 2.469 1.312 3.453 3.844 II
10-10133X-207 20 .281 .219 .750 1.125 1.1250-18NEF .500 2.438 1.312 3.422 2.844 II
10-10133X-208 20 .455 .361 1.062 1.125 1.1250-18NEF .562 2.933 1.312 3.979 4.188 I
10-10133X-209 20 .589 .511 1.000 1.125 1.1250-18NEF .562 2.621 1.312 3.667 5.188 II
10-10133X-210 20 .530 .441 1.000 1.125 1.1250-18NEF .562 2.621 1.312 3.667 4.688 II
10-10133X-211 20 .900 .791 1.250 1.250 1.1250-18NEF .562 3.063 1.312 4.109 7.188 III
47
QWL – accessories
10-10133X
cable sealing adapter
All dimensions are for reference only.
*For complete order number see pages 4 and 5.
Par t
Number*
Used
With
Shell
Size
Cable Range
B
+.000
–.010
C
+.000
–.010
D Thread
Class 2B-LH
E
Free
±.010
F
+.010
–.020
G
Dia.
+.010
–.020
H
±.045
K
Free
Approx. Type
Max.
Dia.
Min.
Dia.
10-10133X-221 22 .699 .605 1.062 1.250 1.2500-18NEF .562 2.933 1.438 3.979 6.188 II
10-10133X-222 22 .750 .637 1.250 1.375 1.2500-18NEF .562 3.059 1.438 4.105 6.688 III
10-10133X-223 22 .445 .367 1.062 1.250 1.2500-18NEF .562 2.933 1.438 3.979 4.188 II
10-10133X-224 22 1.000 .875 1.500 1.375 1.2500-18NEF .562 3.121 1.438 4.167 7.188 III
10-10133X-225 22 .828 .715 1.125 1.250 1.2500-18NEF .594 2.996 1.438 4.072 6.688 I
10-10133X-226 22 .900 .791 1.250 1.375 1.2500-18NEF .562 3.059 1.438 4.105 7.188 III
10-10133X-227 22 .562 .453 1.125 1.250 1.2500-18NEF .594 2.996 1.438 4.074 5.188 I
10-10133X-228 22 1.101 .984 1.500 1.375 1.2500-18NEF .562 3.121 1.438 4.167 7.688 III
10-10133X-229 22 .589 .511 1.000 1.250 1.2500-18NEF .562 2.750 1.438 3.796 5.188 II
10-10133X-231 22 1.055 .958 1.500 1.375 1.2500-18NEF .562 3.121 1.438 4.167 7.688 III
10-10133X-241 24 1.000 .875 1.500 1.625 1.3750-18NEF .562 3.121 1.562 4.167 7.188 III
10-10133X-242 24 .562 .453 1.125 1.406 1.3750-18NEF .562 2.996 1.562 4.042 5.188 II
10-10133X-243 24 .750 .637 1.250 1.375 1.3750-18NEF .562 3.059 1.562 4.105 6.688 I
10-10133X-244 24 .900 .791 1.250 1.375 1.3750-18NEF .562 3.059 1.562 4.105 7.188 I
10-10133X-245 24 1.101 .984 1.500 1.625 1.3750-18NEF .562 3.121 1.562 4.167 7.688 III
10-10133X-246 24 .405 .316 1.000 1.375 1.3750-18NEF .562 2.750 1.562 3.796 3.688 II
10-10133X-247 24 .828 .715 1.125 1.406 1.3750-18NEF .562 2.996 1.562 4.042 6.688 II
10-10133X-248 24 .805 .692 1.250 1.375 1.3750-18NEF .562 3.059 1.562 4.105 6.688 I
10-10133X-249 24 1.130 1.005 1.750 1.812 1.3750-18NEF .562 3.204 1.562 4.250 7.188 III
10-10133X-281 28 1.055 .958 1.500 1.625 1.6250-18NEF .562 3.121 1.812 4.167 7.688 I
10-10133X-282 28 .900 .791 1.250 1.625 1.6250-18NEF .562 3.059 1.812 4.105 7.188 II
10-10133X-283 28 1.000 .875 1.500 1.625 1.6250-18NEF .562 3.121 1.812 4.167 7.188 I
10-10133X-284 28 .630 .535 1.250 1.625 1.6250-18NEF .562 3.059 1.812 4.105 5.688 II
10-10133X-285 28 .750 .637 1.250 1.625 1.6250-18NEF .562 3.059 1.812 4.105 6.688 II
10-10133X-286 28 1.180 1.099 1.750 1.875 1.6250-18NEF .562 3.184 1.812 4.230 8.188 III
10-10133X-287 28 1.101 .984 1.500 1.625 1.6250-18NEF .562 3.121 1.812 4.167 7.688 I
10-10133X-288 28 1.310 1.200 1.750 1.875 1.6250-18NEF .562 3.184 1.812 4.230 8.688 III
10-10133X-289 28 1.230 1.105 1.750 1.875 1.6250-18NEF .562 3.184 1.812 4.230 8.188 III
10-10133X-290 28 .880 .755 1.500 1.625 1.6250-18NEF .562 3.121 1.812 4.167 6.688 I
10-10133X-291 28 .957 .857 1.250 1.625 1.6250-18NEF .547 3.059 1.812 4.090 7.188 II
10-10133X-292 28 .828 .715 1.125 1.625 1.6250-18NEF .562 2.954 1.812 4.000 6.688 II
10-10133X-293 28 1.375 1.250 2.000 1.875 1.6250-18NEF .562 3.184 1.812 4.230 9.688 III
10-10133X-294 28 1.445 1.320 2.000 1.875 1.6250-18NEF .562 3.184 1.812 4.230 9.688 III
10-10133X-295 28 .805 .692 1.250 1.625 1.6250-18NEF .562 3.059 1.812 4.105 6.688 II
10-10133X-321 32 .880 .755 1.500 1.875 1.8750-16N .562 3.121 2.062 4.167 6.688 II
10-10133X-322 32 1.101 .984 1.500 1.875 1.8750-16N .562 3.121 2.062 4.167 7.688 II
10-10133X-323 32 .750 .637 1.250 1.875 1.8750-16N .562 3.059 2.062 4.105 6.688 II
10-10133X-324 32 1.445 1.320 2.000 2.062 1.8750-16N .672 3.246 2.062 4.292 9.688 III
10-10133X-325 32 1.180 1.099 1.750 1.875 1.8750-16N .562 3.184 2.062 4.230 8.188 I
10-10133X-326 32 .375 .312 .875 1.875 1.8750-16N .500 2.766 2.062 3.750 3.844 II
10-10133X-327 32 .957 .857 1.250 1.875 1.8750-16N .562 3.059 2.062 4.105 7.188 II
10-10133X-328 32 1.230 1.105 1.750 1.875 1.8750-16N .562 3.184 2.062 4.230 8.188 I
10-10133X-329 32 1.530 1.406 2.000 2.062 1.8750-16N .562 3.246 2.062 4.292 10.688 III
10-10133X-330 32 1.000 .875 1.500 1.875 1.8750-16N .562 3.121 2.062 4.167 7.188 II
10-10133X-331 32 1.375 1.250 2.000 2.062 1.8750-16N .562 3.246 2.062 4.292 9.688 III
10-10133X-332 32 1.310 1.200 1.750 1.875 1.8750-16N .562 3.184 2.062 4.230 8.688 I
10-10133X-333 32 .580 x
.825 (Oval) 1.500 1.875 1.8750-16N .562 3.121 2.062 4.167 6.688 II
10-10133X-334 32 .500 x
.705 (Oval) 1.500 1.875 1.8750-16N .562 3.121 2.062 4.167 6.688 II
48
QWL – accessories
10-10133X
cable sealing adapter
All dimensions are for reference only.
*For complete order number see pages 4 and 5.
Par t
Number*
Used
With
Shell
Size
Cable Range
B
+.000
–.010
C
+.000
–.010
D Thread
Class 2B-LH
E
Free
±.035
F
+.010
–.020
G
Dia.
+.010
–.020
H
±.045
K
Free
Approx. Type
Max.
Dia.
Min.
Dia.
10-10133X-335 32 .530 .441 1.000 1.625 1.8750-16N .562 2.875 2.062 3.921 4.688 II
10-10133X-336 32 .680 .567 1.250 1.875 1.8750-16N .562 3.059 2.062 4.105 6.688 II
10-10133X-337 32 .463 .406 .875 1.875 1.8750-16N .500 2.766 2.062 3.750 4.344 II
10-10133X-361 36 1.055 .958 1.500 2.062 2.0625-16N .562 3.121 2.312 4.167 7.688 II
10-10133X-362 36 1.445 1.320 2.000 2.062 2.0625-16N .562 3.246 2.312 4.292 9.688 I
10-10133X-363 36 1.530 1.406 2.000 2.062 2.0625-16N .562 3.246 2.312 4.292 10.688 I
10-10133X-364 36 1.230 1.105 1.750 2.062 2.0625-16N .562 3.184 2.312 4.230 8.188 II
10-10133X-365 36 .750 .637 1.250 2.062 2.0625-16N .562 3.059 2.312 4.105 6.688 II
10-10133X-366 36 .880 .755 1.500 2.062 2.0625-16N .562 3.121 2.312 4.167 6.688 II
10-10133X-367 36 1.656 1.531 2.250 2.312 2.0625-16N .562 3.308 2.312 4.354 12.688 III
10-10133X-368 36 1.101 .984 1.500 2.062 2.0625-16N .562 3.121 2.312 4.167 7.688 II
10-10133X-369 36 .957 .857 1.250 2.062 2.0625-16N .672 3.059 2.312 4.090 7.188 II
10-10133X-370 36 1.900 1.775 2.438 2.312 2.0625-16N .500 3.500 2.312 4.656 13.688 III
10-10133X-371 36 .375 .312 .875 2.062 2.0625-16N .500 2.813 2.312 3.797 3.844 II
10-10133X-372 36 1.825 1.700 2.438 2.312 2.0625-16N .672 3.500 2.312 4.656 13.688 III
10-10133X-373 36 1.375 1.250 2.000 2.062 2.0625-16N .562 3.246 2.312 4.292 9.688 I
10-10133X-374 36 1.562 1.437 2.250 2.312 2.0625-16N .562 3.308 2.312 4.354 11.188 III
10-10133X-375 36 1.730 1.605 2.438 2.312 2.0625-16N .672 3.500 2.312 4.656 13.688 III
10-10133X-376 36 .530 .441 1.000 1.875 2.0625-16N .562 2.875 2.312 3.921 4.688 II
10-10133X-377 36 1.130 1.005 1.750 2.062 2.0625-16N .562 3.184 2.312 4.230 7.188 II
10-10133X-378 36 1.180 1.055 1.750 2.062 2.0625-16N .562 3.184 2.312 4.230 8.188 II
10-10133X-379 36 1.595 1.470 2.250 2.312 2.0625-16N .562 3.308 2.312 4.354 11.688 III
10-10133X-401 40 1.310 1.200 1.750 2.312 2.3125-16N .562 3.184 2.562 4.230 8.688 II
10-10133X-402 40 1.656 1.531 2.250 2.312 2.3125-16N .562 3.308 2.562 4.354 12.688 I
10-10133X-403 40 1.101 .984 1.500 2.312 2.3125-16N .438 3.121 2.562 4.167 7.688 II
10-10133X-404 40 1.562 1.437 2.250 2.312 2.3125-16N .562 3.308 2.562 4.354 11.188 I
10-10133X-405 40 1.375 1.250 2.000 2.312 2.3125-16N .562 3.246 2.562 4.292 9.688 II
10-10133X-406 40 1.180 1.099 1.750 2.312 2.3125-16N .562 3.184 2.562 4.230 8.188 II
10-10133X-407 40 1.900 1.775 2.438 2.500 2.3125-16N .672 3.469 2.562 4.625 13.688 III
10-10133X-408 40 1.730 1.605 2.438 2.500 2.3125-16N .672 3.469 2.562 4.625 13.688 III
10-10133X-409 40 1.825 1.700 2.438 2.500 2.3125-16N .672 3.469 2.562 4.625 13.688 III
10-10133X-410 40 1.984 1.859 2.438 2.500 2.3125-16N .672 3.469 2.562 4.625 13.688 III
10-10133X-411 40 1.445 1.320 2.000 2.312 2.3125-16N .562 3.246 2.562 4.292 9.688 II
10-10133X-412 40 2.062 1.937 2.750 2.500 2.3125-16N .672 3.500 2.562 4.656 14.188 III
10-10133X-413 40 2.100 1.955 2.750 2.500 2.3125-16N .672 3.500 2.562 4.656 14.188 III
10-10133X-414 40 2.145 2.000 2.750 2.500 2.3125-16N .672 3.500 2.562 4.656 14.188 III
10-10133X-415 40 .957 .857 1.250 2.125 2.3125-16N .562 3.063 2.562 4.109 7.188 II
10-10133X-416 40 1.230 1.103 1.750 2.312 2.3125-16N .562 3.184 2.562 4.230 8.188 II
10-10133X-417 40 1.055 .958 1.500 2.312 2.3125-16N .562 3.121 2.562 4.167 7.688 II
10-10133X-418 40 .630 .567 1.250 2.250 2.3125-16UN .562 3.063 2.562 4.109 6.688 II
10-10133X-441 44 2.170 2.025 2.750 2.625 2.6250-16UN .672 3.609 2.875 4.953 17.188 III
10-10133X-442 44 2.145 2.000 2.750 2.625 2.6250-16UN .672 3.547 2.875 4.891 14.188 III
10-10133X-443 44 2.250 2.105 2.750 2.625 2.6250-16UN .672 3.609 2.875 4.953 17.188 III
10-10133X-445 44 1.130 1.005 1.750 2.625 2.6250-16UN .562 3.969 2.875 5.203 7.188 II
10-10133X-446 44 1.109 .984 1.500 2.500 2.6250-16UN .562 3.905 2.875 5.140 7.688 II
10-10133X-449 44 1.445 1.320 2.000 2.562 2.6250-16UN .562 4.031 2.875 5.265 9.688 II
10-10133X-481 48 1.900 1.775 2.438 2.812 2.8750-16N .562 3.203 3.125 4.547 13.688 II
10-10133X-482 48 2.000 1.867 2.750 2.969 2.8750-16N .672 4.281 3.125 5.625 14.188 II
10-10133X-483 48 2.250 2.105 2.750 2.750 2.8750-16N .672 4.406 3.125 5.750 17.188 I
10-10133X-484 48 2.170 2.025 2.750 2.750 2.8750-16N .672 4.406 3.125 5.750 17.188 I
49
QWL – accessories
10-113637
cable sealing adapter (with woven strain relief)
Type I Straight
Type II Step Down
Type III Step Up
H
K
BD
LEFT HAND
GC
A
F
E
SECTION A-A
A
H
D
LEFT HAND
G
F
E
K*
Optional
B
C
BD
LEFT HAND
GC
A
F
SECTION A-A
A
H
E
K*
Optional
50
QWL – accessories
10-113637
cable sealing adapter (with woven strain relief)
All dimensions are for reference only.
*For complete order number see pages 4 and 5.
Par t
Number*
Used
With
Shell
Size
Cable Range
B
+.000
–.010
C
+.010
–.000
D Thread
Class 2B-LH
E
Free
±.035
F
+.010
–.020
G
Dia.
+.010
–.020
H
±.045
K
Free
Approx. Type
Max.
Dia.
Min.
Dia.
10-113637-141 14S .337 .281 .750 .750 .7500-20UNEF .500 5.282 .938 6.094 3.344 I
10-113637-142 14S .405 .316 1.000 1.000 .7500-20UNEF .562 5.500 .938 6.374 3.688 III
10-113637-143 14S .530 .441 1.000 1.000 .7500-20UNEF .562 5.500 .938 6.374 4.688 III
10-113637-144 14S .463 .406 .875 .938 .7500-20UNEF .500 5.344 .938 6.156 4.344 III
10-113637-171 16 .699 .605 1.062 1.125 .8750-20UNEF .562 5.563 1.062 6.609 6.188 III
10-113637-172 16 .530 .441 1.000 1.000 .8750-20UNEF .562 5.500 1.062 6.546 4.688 III
10-113637-181 18 .828 .715 1.125 1.250 1.0000-20UNEF .562 6.657 1.188 7.703 6.688 III
10-113637-201 20 .750 .637 1.250 1.312 1.1250-18NEF .562 6.000 1.312 7.046 6.688 III
10-113637-202 20 .984 .875 1.500 1.625 1.1250-18NEF .562 6.750 1.312 7.796 7.188 III
10-113637-203 20 .900 .791 1.250 1.312 1.1250-18UNEF .562 6.000 1.312 7.046 7.188 III
10-113637-221 22 .750 .637 1.250 1.312 1.2500-18NEF .562 6.000 1.438 7.046 6.688 III
10-113637-222 22 .699 .605 1.062 1.312 1.2500-18NEF .562 5.063 1.438 6.109 6.188 II
10-113637-223 22 1.055 .958 1.500 1.625 1.2500-18NEF .562 6.750 1.438 7.796 7.688 III
10-113637-224 22 1.828 .715 1.125 1.250 1.2500-18NEF .562 5.625 1.438 6.671 6.688 I
10-113637-225 22 .589 .511 1.000 1.250 1.2500-18NEF .562 5.500 1.438 6.546 5.188 II
10-113637-241 24 .957 .857 1.250 1.375 1.3750-18NEF .562 6.000 1.562 7.046 7.188 I
10-113637-242 24 .750 .637 1.250 1.375 1.3750-18NEF .562 6.000 1.562 7.046 6.688 I
10-113637-243 24 1.101 .984 1.500 1.625 1.3750-18NEF .562 6.750 1.562 7.796 7.688 III
10-113637-244 24 1.000 .875 1.500 1.625 1.3750-18NEF .562 6.750 1.562 7.796 7.188 III
10-113637-245 24 1.180 1.055 1.750 1.812 1.3750-18NEF .562 6.813 1.562 7.859 8.188 III
10-113637-246 24 .805 .692 1.250 1.375 1.3750-18NEF .562 6.000 1.562 7.046 6.688 I
10-113637-281 28 1.000 .875 1.500 1.562 1.6250-18NEF .562 6.750 1.812 7.796 7.188 I
10-113637-282 28 1.900 1.775 2.438 2.438 1.6250-18NEF .672 8.125 1.812 9.281 13.688 III
10-113637-283 28 1.375 1.250 2.000 2.000 1.6250-18NEF .562 6.875 1.812 7.921 9.688 III
10-113637-284 28 .750 .637 1.250 1.562 1.6250-18NEF .562 5.750 1.812 6.796 6.688 II
10-113637-285 28 1.101 .984 1.500 1.562 1.6250-18NEF .562 6.750 1.812 7.796 7.688 I
10-113637-286 28 1.130 1.005 1.750 1.875 1.6250-18NEF .562 6.813 1.812 7.859 7.188 III
10-113637-287 28 .900 .791 1.250 1.562 1.6250-18NEF .562 5.750 1.812 6.796 7.188 II
10-113637-288 28 1.427 1.320 2.000 2.000 1.6250-18NEF .562 6.875 1.812 7.921 9.688 III
10-113637-289 28 1.180 1.099 1.750 1.875 1.6250-18NEF .562 6.812 1.812 7.858 8.188 III
10-113637-290 28 1.055 .958 1.500 1.562 1.6250-18NEF .562 6.750 1.812 7.796 7.688 I
10-113637-291 28 .957 .857 1.250 1.562 1.6250-18NEF .562 5.750 1.812 6.796 7.188 II
10-113637-292 28 1.310 1.200 1.750 1.875 1.6250-18NEF .562 6.813 1.812 7.859 8.688 III
10-113637-293 28 .530 .441 1.000 1.625 1.6250-18NEF .562 6.500 1.812 7.546 4.688 II
10-113637-294 28 1.230 1.105 1.750 1.875 1.6250-18NEF .562 6.813 1.812 7.859 8.188 III
10-113637-295 28 .630 .535 1.250 1.562 1.6250-18NEF .562 5.750 1.812 6.796 5.688 II
51
QWL – accessories
10-113637
cable sealing adapter (with woven strain relief)
All dimensions are for reference only.
*For complete order number see pages 4 and 5.
Par t
Number*
Used
With
Shell
Size
Cable Range
B
+.000
–.010
C
+.010
–.000
D Thread
Class 2B-LH
E
Free
±.035
F
+.010
–.020
G
Dia.
+.010
–.020
H
±.045
K
Free
Approx. Type
Max.
Dia.
Min.
Dia.
10-113637-321 32 .828 .715 1.125 1.844 1.8750-16N .594 7.625 2.062 8.703 6.688 II
10-113637-322 32 1.310 1.200 1.750 1.812 1.8750-16UN .562 6.812 2.062 7.858 8.688 I
10-113637-323 32 1.130 1.005 1.750 1.812 1.8750-16UN .562 6.812 2.062 7.858 7.188 I
10-113637-324 32 1.375 1.250 2.000 2.000 1.8750-16UN .562 7.875 2.062 8.921 9.688 III
10-113637-325 32 1.445 1.320 2.000 2.000 1.8750-16UN .562 7.875 2.062 8.921 9.688 III
10-113637-326 32 1.180 1.099 1.750 1.812 1.8750-16UN .562 6.812 2.062 7.858 8.188 I
10-113637-327 32 1.656 1.531 2.250 2.250 1.8750-16UN .562 7.141 2.062 8.187 12.688 III
10-113637-328 32 .970 .857 1.250 1.844 1.8750-16UN .562 6.688 2.062 7.734 7.188 II
10-113637-361 36 1.375 1.250 2.000 2.000 2.0625-16N .562 6.875 2.312 7.921 9.688 I
10-113637-362 36 1.000 .875 1.500 2.000 2.0625-16N .562 6.750 2.312 7.796 7.188 II
10-113637-363 36 1.920 x
1.140 oval
1.920 x
1.140 oval 2.438 2.438 2.0625-16N .672 8.125 2.312 9.281 13.688 III
10-113637-364 36 1.230 1.105 1.750 2.000 2.0625-16N .562 6.813 2.312 7.859 8.188 II
10-113637-365 36 1.562 1.437 2.250 2.250 2.0625-16N .562 6.938 2.312 7.984 11.188 III
10-113637-366 36 1.656 1.531 2.250 2.250 2.0625-16N .562 6.938 2.312 7.984 11.188 III
10-113637-367 36 1.445 1.320 2.000 2.000 2.0625-16N .562 6.875 2.312 7.921 9.688 I
10-113637-368 36 1.825 1.700 2.438 2.500 2.0625-16N .672 9.125 2.312 9.281 13.688 III
10-113637-369 36 1.895 1.775 2.438 2.438 2.0625-16N .672 8.125 2.312 9.281 13.688 III
10-113637-370 36 1.730 1.605 2.438 2.438 2.0625-16N .672 8.125 2.312 9.281 13.688 III
10-113637-371 36 1.310 1.200 1.750 2.000 2.0625-16N .562 6.813 2.312 7.859 8.688 II
10-113637-401 40 1.906 1.761 2.750 2.438 2.3125-16N .672 8.125 2.562 9.281 14.188 III
10-113637-402 40 1.940 1.815 2.438 2.438 2.3125-16N .672 8.125 2.562 9.281 13.688 III
10-113637-403 40 1.900 1.775 2.438 2.438 2.3125-16N .672 8.125 2.562 9.281 13.688 III
10-113637-404 40 1.825 1.700 2.438 2.438 2.3125-16N .672 8.125 2.562 9.281 13.688 III
10-113637-405 40 1.310 1.200 1.750 2.250 2.3125-16N .562 7.813 2.562 8.859 8.688 II
10-113637-406 40 1.180 1.099 1.750 2.250 2.3125-16N .562 7.813 2.562 8.859 8.188 II
10-113637-407 40 1.230 1.105 1.750 2.250 2.3125-16N .562 7.813 2.562 8.859 8.188 II
10-113637-408 40 1.656 1.531 2.250 2.250 2.3125-16N .562 7.938 2.562 8.984 11.188 I
10-113637-410 40 2.145 2.000 2.750 2.438 2.3125-16N .672 8.125 2.562 9.281 14.188 III
10-113637-411 40 1.984 1.859 2.438 2.438 2.3125-16N .672 8.125 2.562 9.281 13.688 III
10-113637-412 40 1.940 1.815 2.438 2.438 2.3125-16N .672 11.125 2.562 12.281 13.688 III
10-113637-413 40 1.984 1.859 2.438 2.438 2.3125-16N .672 11.125 2.562 12.281 13.688 III
10-113637-414 40 2.100 1.955 2.750 2.625 2.3125-16N .672 12.000 2.562 13.156 14.188 III
10-113637-415 40 1.562 1.437 2.250 2.250 2.3125-16N .562 7.938 2.562 8.984 11.188 I
10-113637-416 40 1.445 1.320 2.000 2.312 2.3125-16N .562 6.875 2.562 7.921 9.688 II
10-113637-417 40 1.375 1.250 2.000 2.312 2.3125-16N .562 6.875 2.562 7.921 9.688 II
52
QWL – accessories
10-113637
cable sealing adapter (with woven strain relief)
All dimensions are for reference only.
*For complete order number see pages 4 and 5.
Par t
Number*
Used
With
Shell
Size
Cable Range
B
+.000
–.010
C
+.010
–.000
D Thread
Class 2B-LH
E
Free
±.035
F
+.010
–.020
G
Dia
+.010
–.020
H
±.045
K
Free†
Approx. Type
Max
Dia
Min
Dia
10-113637-441 44 2.100 1.955 2.750 2.750 2.6250-16UN .672 8.125 2.875 9.469 14.188 III
10-113637-442 44 2.250 2.105 2.750 2.875 2.6250-16UN .672 8.188 2.875 9.531 17.188 III
10-113637-443 44 2.000 1.867 2.750 2.750 2.6250-16UN .672 8.125 2.875 9.469 14.188 III
10-113637-444 44 1.500 1.375 2.250 2.500 2.6250-16UN .562 7.938 2.875 9.171 11.188 II
10-113637-445 44 1.730 1.605 2.438 2.750 2.6250-16UN .672 8.125 2.875 9.469 13.688 II
10-113637-446 44 .750 .637 1.250 2.625 2.6250-16UN .562 6.688 2.875 7.921 6.688 II
10-113637-447 44 1.825 1.700 2.438 2.750 2.6250-16UN .672 8.125 2.875 9.469 13.688 II
10-113637-448 44 2.145 2.000 2.750 2.750 2.6250-16UN .672 8.125 2.875 9.469 14.188 III
10-113637-449 44 2.170 2.025 2.750 2.875 2.6250-16UN .672 8.188 2.875 9.532 17.188 III
10-113637-450 44 1.375 1.250 2.000 2.625 2.6250-16UN .562 7.875 2.875 9.109 9.688 II
10-113637-481 48 2.250 2.105 2.750 2.750 2.8750-16N .672 8.188 3.125 9.532 14.688 I
10-113637-482 48 2.500 2.355 2.875 2.875 2.8750-16N .672 8.188 3.125 9.532 18.188 III
10-113637-483 48 2.375 2.230 2.875 2.875 2.8750-16N .672 8.188 3.125 9.532 18.188 III
10-113637-484 48 2.145 2.000 2.750 2.875 2.8750-16N .672 8.125 3.125 9.469 14.188 II
10-113637-485 48 2.000 1.867 2.750 2.875 2.8750-16N .672 8.125 3.125 9.469 14.188 II
10-113637-486 48 1.656 1.531 2.250 2.750 2.8750-16UN .562 7.937 3.125 9.171 12.688 II
53
QWL – accessories
adapter, cable clamp
10-113196-XX
adapter
10-749XX-( )
cable clamp
This cable clamp is designed to be used with specific QWL insert arrangements. The locations,
quantity, and sizes of holes in the clamp grommet must correspond to those in the connector for an
effective moisture seal without wire crossing. Contact Amphenol, Sidney, NY, for grommet avail-
ability. Example: 10-107618-4P must use 10-74918-4 clamp.
V
E
L
D
A
C
F
Y
WZ
54
B
DIA
45
A
DIA
C
.135 +.030
–.025
˚
QWL – accessories
adapter, cable clamp, sealing plugs
All dimensions for reference only.
*For complete order number see page 5. Clamp 10-749XX-( ) has a bright cadmium finish. An olive drab cadmium plate finish is available
by order number 71-749XX-( ). To complete clamp order number, add connector insert arrangement number.
Shell
Size
Adapter
Part
Number*
Clamp
Part
Number*
A Thread
Class 2A
C
+.010
–.000
D
Dia.
+.010
–.020
E
Dia.
+.010
–.020
F
±.010
L
±.010
V Thread
Class 2B-LH
W
Min.
Thd.
Engage
Y
Max.
Z
Max.
10S 10-113196-10 10-74910-( ) .500-28UNEF .203 .922 .625 .562 1.234 .500-28UNEF .519 .807 .529
12S 10-113196-12 10-74912-( ) .625-24NEF .328 .969 .750 .688 1.281 .625-24NEF .519 .901 .524
12 10-113196-13 10-74913-( ) .625-24NEF .328 .954 .750 .688 1.438 .625-24NEF .519 .901 .524
14S 10-113196-14 10-74914-( ) .750-20UNEF .453 1.094 .875 .812 1.406 .750-20UNEF .519 1.026 .524
14 10-113196-15 10-74915-( ) .750-20UNEF .453 .954 .875 .812 1.438 .750-20UNEF .519 1.026 .524
16S 10-113196-16 10-74916-( ) .875-20UNEF .578 1.094 1.000 .938 1.406 .875-20UNEF .519 1.119 .524
16 10-113196-17 10-74917-( ) .875-20UNEF .578 1.016 1.000 .938 1.500 .875-20UNEF .519 1.119 .524
18 10-113196-18 10-74918-( ) 1.000-20UNEF .676 1.141 1.188 1.062 1.625 1.000-20UNEF .519 1.229 .556
20 10-113196-20 10-74920-( ) 1.1875-18NEF .801 1.094 1.312 1.250 1.578 1.125-18NEF .505 1.479 .666
22 10-113196-22 10-74922-( ) 1.1875-18NEF .906 1.141 1.438 1.250 1.625 1.250-18NEF .519 1.479 .666
24 10-113196-24 10-74924-( ) 1.4375-18NEF 1.016 1.094 1.562 1.500 1.578 1.375-18NEF .519 1.666 .666
28 10-113196-28 10-74928-( ) 1.4375-18NEF 1.130 1.235 1.812 1.500 1.719 1.625-18NEF .519 1.666 .666
32 10-113196-32 10-74932-( ) 1.7500-18NS 1.438 1.204 2.062 1.875 1.688 1.875-16N .519 2.135 .805
36 10-113196-36 10-74936-( ) 2.000-18NS 1.678 1.266 2.250 2.125 1.750 2.0625-16N .738 2.260 .805
40 10-113196-40 10-74940-( ) 2.2500-16UN 1.914 1.266 2.500 2.375 1.750 2.3125-16N .738 2.510 .805
SEALING PLUG
MS27488-XX
10-405996-XX
Order No.
Contact
Size
MS
Number
Wire
Size
Color
Code
B
±.005
C
±.010
A
Dia.
±.010
10-405996-16 16 27488-16 20-16 Blue .133 .564* .083
10-405996-12 12 27488-12 14-12 Yellow .171 .564* .121
10-405996-8 8 27488-8 10-8 White .315 .470 .185
10-405996-4 4 27488-4 4-6 Blue .415 .470 .310
10-405996-0 0 27488-0 0-2 Yellow .605 1.000 .440
*±.020
Sealing plugs are used to fill unused holes in multi-holed grommet configurations
55
QWL – accessories
adapter, cable clamp
10-113138-XX
adapter
M85049/2-( )C
cable clamp
V
LEFT HAND
E
D
L
A
B
C
F
Y
M
KA
56
QWL – accessories
adapter, cable clamp, sleeve
Shell
Size
Adapter
Part
Number*
Clamp
MS Part
Number*
A Thread
Class 2A
(Plated)
B Min
Full
Thd
C Dia
+.000
–.010
D
±.020
E Dia
+.010
–.020
F
±.010
K Dia
Cable Range L
Max
M
Max
V
Thread
Class 2B-LH
Y
MaxFree Closed
12 10-113138-12
10-113138-13
M85049/2-4C
M85049/2-4C
.625-24UNEF
.625-24NEF
.422
.422
.386
.386
1.078
1.125
.750
.750
.688
.688 .302 .094 1.390
1.609 1.375 .625-24NEF
.625-24NEF .906
14 10-113138-14
10-113138-15
M85049/2-6C
M85049/2-6C
.750-20UNEF
.750-20UNEF
.422
.422
.500
.500
1.078
1.125
.875
.875
.812
.812 .428 .230 1.390
1.609 1.375 .750-20UNEF
.750-20UNEF 1.031
16 10-113138-16
10-113138-17
M85049/2-8C
M85049/2-8C
.875-20UNEF
.875-20UNEF
.422
.422
.625
.625
1.078
1.125
1.000
1.000
.938
.938 .515 .316 1.390
1.609 1.375 .875-20UNEF
.875-20UNEF 1.125
18 10-113138-18 M85049/2-10C 1.000-20UNEF .422 .752 1.125 1.188 1.062 .614 .378 1.609 1.437 1.000-20UNEF 1.234
20 10-113138-20 M85049/2-12C 1.1875-18UNEF .422 .891 1.125 1.312 1.250 .738 .445 1.609 1.437 1.125-18NEF 1.484
22 10-113138-22 M85049/2-12C 1.1875-18NEF .422 .891 1.125 1.438 1.250 .738 .445 1.609 1.437 1.250-18NEF 1.484
24 10-113138-24 M85049/2-16C 1.4375-18UNEF .422 1.111 1.125 1.562 1.500 .926 .611 1.609 1.562 1.375-18NEF 1.671
28 10-113138-28 M85049/2-16C 1.4375-18NEF .422 1.111 1.297 1.812 1.500 .926 .611 1.781 1.562 1.625-18NEF 1.671
32 10-113138-32 M85049/2-20C 1.750-18UNS .484 1.422 1.297 2.062 1.875 1.200 .922 1.781 1.812 1.875-16UN 2.188
36 10-113138-36 M85049/2-24C 2.000-18UNS .562 1.672 1.297 2.250 2.125 1.363 .922 1.781 2.062 2.0625-16N 2.344
40 10-113138-40 M85049/2-28C 2.250-16UN .562 1.914 1.297 2.500 2.375 1.611 1.180 1.781 2.062 2.3125-16N 2.594
44 10-113138-44 M85049/2-32C 2.500-16UN .562 2.142 1.297 2.812 2.625 1.865 1.427 1.781 2.188 2.625-16UN 2.812
Sleeve not supplied as part of MS3057-( )C assembly.
Order separately by part number shown.
Shell
Size
Sleeve
MS Part
Number
D
Dia.
±.016
Z Dia
Free
±.016 Closed
12 MS3420-4A .302 .219 .010
14 MS3420-4A
MS3420-6A
.302
.427
.219
.312
.020
.114
16 MS3420-6A
MS3420-8A
.427
.531
.312
.438
.085
.220
18 MS3420-6A
MS3420-10A
.427
.615
.312
.438
.085
.200
20 MS3420-10A
MS3420-12A
.615
.740
.438
.541
.177
.270
22 MS3420-10A
MS3420-12A
.615
.740
.438
.541
.177
.270
24
MS3420-8A
MS3420-12A
MS3420-16A
.531
.740
.927
.438
.541
.750
.186
.260
.433
26
MS3420-8A
MS3420-12A
MS3420-16A
.531
.740
.927
.438
.541
.750
.186
.260
.433
32
MS3420-12A
MS3420-16A
MS3420-20A
.740
.927
1.240
.541
.750
.938
.273
.442
.620
36
MS3420-16A
MS3420-20A
MS3420-24A
.927
1.240
1.365
.750
.938
1.125
.358
.504
.682
40
MS3420-16A
MS3420-20A
MS3420-28A
.927
1.240
1.614
.750
.938
1.250
.368
.514
.816
44
MS3420-20A
MS3420-28A
MS3420-32A
1.240
1.614
1.865
.938
1.250
1.625
.638
.897
1.229
MS3420-( )A
sleeve
Z
D
2.000 ± .031
57
10-101046-( ), 10-101531-( )
plug protective covers
10-101063-( ), 10-101048-( )
receptacle protective covers
QWL – accessories
protection caps
L
F
E
10-101046
10-101531
A
C
B
L
D
E
10-101063
10-101048
A
C
B
58
QWL – accessories
protection caps
All dimensions for reference only.
*For complete order number see page 5.
Shell
Size
Without
Eyelet End
Part Number*
With
Eyelet End
Part Number*
A Thread
Class 2A
B
Dia
+.010
–.000
C
Approx.
E
Approx.
F
Flat
±.010
L
Max.
10 10-101046-10 10-101531-10 .6250-0.05P-0.1L-DS .125 3.000 3.375 .500 1.250
12 10-101046-12 10-101531-12 .7500-0.1P-0.2L-DS .125 3.500 3.875 .625 1.438
14 10-101046-14 10-101531-14 .8750-0.1P-0.2L-DS .125 3.500 3.875 .750 1.438
16 10-101046-16 10-101531-16 1.0000-0.1P-0.2L-DS .140 3.500 3.875 .875 1.438
18 10-101046-18 10-101531-18 1.1250-0.1P-0.2L-DS .140 3.500 4.000 1.000 1.438
20 10-101046-20 10-101531-20 1.2500-0.1P-0.2L-DS .193 4.000 4.500 1.062 1.438
22 10-101046-22 10-101531-22 1.3750-0.1P-0.2L-DS .193 4.000 4.500 1.125 1.438
24 10-101046-24 10-101531-24 1.5000-0.1P-0.2L-DS .193 4.500 5.000 1.250 1.438
28 10-101046-28 10-101531-28 1.7500-0.1P-0.2L-DS .193 4.500 5.000 1.500 1.438
32 10-101046-32 10-101531-32 2.0000-0.1P-0.2L-DS .193 5.000 5.500 1.750 1.438
36 10-101046-36 10-101531-36 2.2500-0.1P-0.2L-DS .193 5.000 5.500 2.000 1.438
40 10-101046-40 10-101531-40 2.5000-0.1P-0.2L-DS .193 5.000 5.500 2.250 1.438
44 10-101046-44 10-101531-44 2.7500-0.1P-0.2L-DS .193 6.000 6.000 2.500 1.438
48 10-101046-48 10-101531-48 3.0000-0.1P-0.2L-DS .193 6.000 6.000 2.750 1.438
All dimensions for reference only.
*For complete order number see page 5.
Shell
Size
Without
Eyelet End
Part Number*
With
Eyelet End
Part Number*
A Thread
Class 2B
B
Dia.
+.010
–.000
C
Approx.
D
Dia.
Max.
E
Approx.
L
Max.
10 10-101063-10 10-101048-10 .6250-0.05P-0.1L-DS .140 3.000 .844 3.375 .750
12 10-101063-12 10-101048-12 .7500-0.1P-0.2L-DS .140 3.500 .969 3.875 .750
14 10-101063-14 10-101048-14 .8750-0.1P-0.2L-DS .140 3.500 1.094 3.875 .750
16 10-101063-16 10-101048-16 1.0000-0.1P-0.2L-DS .140 3.500 1.219 3.875 .750
18 10-101063-18 10-101048-18 1.1250-0.1P-0.2L-DS .193 3.500 1.344 4.000 .969
20 10-101063-20 10-101048-20 1.2500-0.1P-0.2L-DS .193 4.000 1.469 4.500 .969
22 10-101063-22 10-101048-22 1.3750-0.1P-0.2L-DS .193 4.000 1.562 4.500 .969
24 10-101063-24 10-101048-24 1.5000-0.1P-0.2L-DS .193 4.500 1.688 5.000 .969
28 10-101063-28 10-101048-28 1.7500-0.1P-0.2L-DS .193 4.500 1.938 5.000 .969
32 10-101063-32 10-101048-32 2.0000-0.1P-0.2L-DS .193 5.000 2.219 5.500 .969
36 10-101063-36 10-101048-36 2.2500-0.1P-0.2L-DS .193 5.000 2.469 5.500 .969
40 10-101063-40 10-101048-40 2.5000-0.1P-0.2L-DS .193 5.000 2.719 5.500 .969
44 10-101063-44 10-101048-44 2.7500-0.1P-0.2L-DS .193 6.000 2.969 6.000 .969
48 10-101063-48 10-101048-48 3.0000-0.1P-0.2L-DS .193 6.000 3.219 6.000 .969
59
QWL – accessories
flange gasket, grip banding clamp
All dimensions for reference only.
*For complete order number see page 5.
Part
Number*
Part
Number*
Shell
Size
F
Dia.
+.016
–.000
R
±.010
S
+.016
–.000
T
Dia.
±.010
10-36675-10 10-40450-10 10 .625 .719 1.000 .172
10-36675-12 10-40450-12 12 .750 .813 1.094 .172
10-36675-14 10-40450-14 14 .875 .906 1.188 .172
10-36675-16 10-40450-16 16 1.000 .969 1.281 .172
10-36675-18 10-40450-18 18 1.125 1.063 1.375 .203
10-36675-20 10-40450-20 20 1.250 1.156 1.500 .203
10-36675-22 10-40450-22 22 1.375 1.250 1.625 .203
10-36675-24 10-40450-24 24 1.500 1.375 1.750 .203
10-36675-28 10-40450-28 28 1.750 1.563 2.000 .203
10-36675-32 10-40450-32 32 2.000 1.750 2.250 .219
10-36675-36 10-40450-36 36 2.188 1.938 2.500 .219
10-36675-40 10-40450-40 40 2.438 2.188 2.750 .219
10-36675-44 10-40450-44 44 2.688 2.375 3.000 .219
10-36675-48 10-40450-48 48 2.938 2.625 3.250 .219
All dimensions for reference only.
*For complete order number see page 5.
Part
Number*
A Dia.
Max. Min.
10-183249-10 1.125 .812
10-183249-11 1.312 .938
10-183249-12 1.500 1.125
10-183249-13 1.688 1.312
10-183249-14 1.875 1.500
10-183249-15 2.062 1.688
10-183249-16 2.250 1.875
10-183249-17 2.438 2.062
10-183249-18 2.625 2.250
10-183249-19 2.812 2.438
10-183249-20 3.000 2.625
10-36675-( )
10-40450-( )
flange gaskets
10-183249-( )
grip banding clamp
S
F
T
4 HOLES
R
(TP)
R
(TP)
.031 ± ,010 (10-36675)
.031 ± .005 (10-40450)
.375
REF.
A
