Technical Data Sheet Silicon PIN Photodiode PD15-22C/TR8 Features Fast response time High photo sensitivity Small junction capacitance Pb free The product itself will remain within RoHS compliant version. Descriptions PD15-22C/TR8 is a high speed and high sensitive PIN photodiode in miniature flat top view lens SMD package and it is molded in a water clear plastic. The device is Spectrally matched to visible and infrared emitting diode. Applications High speed photo detector Copier Game machine Device Selection Guide LED Part No. Chip Material Lens Color PD15-22C/TR8 Silicon Water clear Everlight Electronics Co., Ltd. Device No DTD-152-001 http://www.everlight.com Prepared date 09-21-2007 Rev 1 Page: 1 of 10 Prepared by Jaine Tsai PD15-22C/TR8 2.1 1.1 0.45 0.9 2.3 0.9 Package Dimensions 2.0 3.3 2.3 1.2 1.4 2.8 1.4 1.0 2.1 4-R0.25 Notes: 1.All dimensions are in millimeters 2.Tolerances unless dimensions 0.1mm Absolute Maximum Ratings (Ta=25 ) Parameter Symbol Rating Reverse Voltage VR 32 Units V Operating Temperature Topr -25 ~ +85 Storage Temperature Tstg -40 ~ +100 Soldering Temperature*1 Tsol 260 Power Dissipation at(or below) 25Free Air Temperature Pc 150 mW Notes: *1:Soldering time5 seconds. Everlight Electronics Co., Ltd. Device No DTD-152-001 http://www.everlight.com Prepared date 09-21-2007 Rev 1 Page: 2 of 10 Prepared by Jaine Tsai PD15-22C/TR8 Electro-Optical Characteristics (Ta=25 ) Parameter Symbol Condition Min Typ Max Unit Rang Of Spectral Bandwidth 10% of P 400 --- 1100 nm Wavelength Of Peak Sensitivity P --- --- 940 --- nm Open-Circuit Voltage VOC Ee=5mW /cm2 P=940nm --- 0.41 --- V Short-Circuit Current ISC Ee=1mW /cm2 P=875nm 4.0 6.5 --- A Reverse Light Current IL Ee=1mW /cm2 P=875nm VR=5V 4.2 6.5 --- A Dark Reverse Current ID Ee=0mW /cm2 VR=10V --- --- 10 nA BVR Ee=0mW /cm2 IR=100A 32 170 --- V Total Capacitance Ct Ee=0mW /cm2 f=1MHz VR=5V --- 6 --- pF Rise Time tr --- 10 --- Fall Time tf --- 10 --- Reverse Breakdown Voltage Everlight Electronics Co., Ltd. Device No DTD-152-001 VR=5V RL=1000 http://www.everlight.com Prepared date 09-21-2007 nS Rev 1 Page: 3 of 10 Prepared by Jaine Tsai PD15-22C/TR8 Typical Electro-Optical Characteristics Curves Fig.1 Power Dissipation vs. Ambient Temperature Fig.2 Spectral Sensitivity 200 1.0 O Ta=25 C 150 100 0.5 50 0 0 -25 25 0 50 400 500 600 700 800 900 1000 1100 1200 75 85 100 Fig.3 Dark Current vs. Ambient Temperature 1000 Fig.4 Reverse Light Current vs. Ee 20 15 100 10 10 5 VR=5V VR=10V 1 20 40 60 80 100 0 0.5 1.5 1.0 3.0 2 Everlight Electronics Co., Ltd. Device No DTD-152-001 http://www.everlight.com Prepared date 09-21-2007 Rev 1 Page: 4 of 10 Prepared by Jaine Tsai PD15-22C/TR8 Typical Electro-Optical Characteristics Curves Fig.5 Terminal Capacitance vs. Reverse Voltage t 10 Fig.6 Response Time vs. Load Resistance f=1MHZ VR=5V 10 1 VR=10V Ta=25C 2 0 8 10 6 10 4 10 2 10 -1 -2 -3 0.1 1 Everlight Electronics Co., Ltd. Device No DTD-152-001 10 100 10 http://www.everlight.com Prepared date 1 09-21-2007 2 10 Rev 1 3 10 10 4 Page: 5 of 10 Prepared by Jaine Tsai 5 10 PD15-22C/TR8 Precautions For Use 1. Over-current-proof Customer must apply resistors for protection , otherwise slight voltage shift will cause big current change ( Burn out will happen ). 2. Storage 2.1 Do not open moisture proof bag before the products are ready to use. 2.2 Before opening the package, the LEDs should be kept at 30 or less and 90%RH or less. 2.3 The LEDs should be used within a year. 2.4 After opening the package, the LEDs should be kept at 30 or less and 70%RH or less. 2.5 The LEDs should be used within 168 hours (7 days) after opening the package. 2.6 If the moisture absorbent material (silica gel) has faded away or the LEDs have exceeded the storage time, baking treatment should be performed using the following conditions. Baking treatment : 605 for 24 hours. 3. Soldering Condition 3.1 Pb-free solder temperature profile 3.2 Reflow soldering should not be done more than two times. 3.3 When soldering, do not put stress on the LEDs during heating. 3.4 After soldering, do not warp the circuit board. Everlight Electronics Co., Ltd. Device No DTD-152-001 http://www.everlight.com Prepared date 09-21-2007 Rev 1 Page: 6 of 10 Prepared by Jaine Tsai PD15-22C/TR8 4.Soldering Iron Each terminal is to go to the tip of soldering iron temperature less than 350 for 3 seconds within once in less than the soldering iron capacity 25W. Leave two seconds and more intervals, and do soldering of each terminal. Be careful because the damage of the product is often started at the time of the hand solder. 5.Repairing Repair should not be done after the LEDs have been soldered. When repairing is unavoidable, a double-head soldering iron should be used (as below figure). It should be confirmed beforehand whether the characteristics of the LEDs will or will not be damaged by repairing. Everlight Electronics Co., Ltd. Device No DTD-152-001 http://www.everlight.com Prepared date 09-21-2007 Rev 1 Page: 7 of 10 Prepared by Jaine Tsai PD15-22C/TR8 Reliability Test Item And Condition The reliability of products shall be satisfied with items listed below. Confidence level90% LTPD10% NO. Item Test Conditions Test Hours/ Sample Failure Cycles Sizes Judgement Ac/Re Criteria 1 REFLOW Soldering TEMP.2605 10secs 2 Temperature Cycle H : +100 L : -40 3 Thermal Shock 22pcs 0/1 ILLx0.8 15mins 50Cycles 5mins 15mins 22pcs 5mins 50Cycles 10secs 5mins 22pcs H :+100 L :-10 4 High Temperature 6Mins 0/1 LLower Specification Limit 0/1 TEMP.+100 1000hrs 22pcs 0/1 TEMP.-40 1000hrs 22pcs 0/1 1000hrs 22pcs 0/1 1000hrs 22pcs 0/1 Storage 5 Low Temperature Storage 6 DC Operating Life VR=5V 7 High Temperature/ 85 / 85% R.H High Humidity Everlight Electronics Co., Ltd. Device No DTD-152-001 http://www.everlight.com Prepared date 09-21-2007 Rev 1 Page: 8 of 10 Prepared by Jaine Tsai . PD15-22C/TR8 Package Dimensions 1. Reel Dimensions Note: The tolerances unless mentioned is 0.1mm ,Unit = mm 2. Carrier Tape Dimensions:(Quantity: 2000pcs/reel) 2.00.05 4.0 0.23 3.35 2 8.0 3.50.05 1.75 1.550.05 1 4.0 2.95 1 Anode 2 Cathode 1.65 Note: The tolerances unless mentioned is 0.1mm ,Unit = mm Everlight Electronics Co., Ltd. Device No DTD-152-001 http://www.everlight.com Prepared date 09-21-2007 Rev 1 Page: 9 of 10 Prepared by Jaine Tsai PD15-22C/TR8 Packing Procedure Aluminum moistue-proof bag Label Desiccant Label Label Form Specification CPN: Customer's Production Number P/N : Production Number QTY: Packing Quantity CAT: Ranks RoHS PD15-22C/TR8 HUE: Peak Wavelength REF: Reference LOT No: Lot Number MADE IN TAIWAN: Production Place Notes 1. Above specification may be changed without notice. EVERLIGHT will reserve authority on material change for above specification. 2. When using this product, please observe the absolute maximum ratings and the instructions for using outlined in these specification sheets. EVERLIGHT assumes no responsibility for any damage resulting from use of the product which does not comply with the absolute maximum ratings and the instructions included in these specification sheets. 3. These specification sheets include materials protected under copyright of EVERLIGHT corporation. Please don't reproduce or cause anyone to reproduce them without EVERLIGHT's consent. EVERLIGHT ELECTRONICS CO., LTD. Office: No 25, Lane 76, Sec 3, Chung Yang Rd, Tucheng, Taipei 236, Taiwan, R.O.C Everlight Electronics Co., Ltd. Device No DTD-152-001 Tel: 886-2-2267-2000, 2267-9936 Fax: 886-2267-6244, 2267-6189, 2267-6306 http://www.everlight.com http://www.everlight.com Prepared date 09-21-2007 Rev 1 Page: 10 of 10 Prepared by Jaine Tsai