and       aretrademarksorregisteredtrademarksofCITIZENHOLDINGSCO.,LTD.JAPAN.
isatrademarkoraregisteredtrademarkofCITIZENELECTRONICSCO.,LTD.JAPAN.
DATASHEET
CL-L104-C3N-F
Ref.CE-P236503/13
1/11
1. Scope of Application
This data sheet is applied to the chip type LED lamp , model CL-L104-C3N-F.
2. Part code
C L - L 1 0 4 - C 3 N - F
Series
L104 : White power LED for general lighting.
Watt class
Lighting color
N : Correlated Color Temp eratu re 5000K.
Symbol
CITILED
Name CL-L104-C3N-F
CITIZEN ELECTRONICS CO.,LTD. JAPA N
DA TA SHEET
Ref.CE-P236503/13R1(0613)
2/11
3. Outline drawing
4. Performance
( 1 ) Absolute Maximum Rating
Symbol Unit
Power Dissipation PDW
Forward Current IFmA
Mnimum current IF Min mA
Reverse Current IRmA
Operating Temperature TOP C
Storage Temperature TST C
Junction Temperature Tj Max C*1
*1 D.C. Current : Tj = Tc + Rj-c × PD
Symbol
CITILED
Name CL-L104-C3N-F
DA TA SHEET
CITIZEN ELECTRONICS CO.,LTD. JAPAN
Parameter Rating Value
7.8
720
30
1
-40 ~ +100
-30 ~ +85
120
Fir st line :
CEJL104
Second line :
9.2350120 Maximum junction temperture Tj=120C
Rated supply current 350mA
Rated supply voltage 9.2V
Model number
CITIZEN ELECTRONICS CO.,LTD. JAPAN
First line : Serial N o.
Second line :
E3NF Color
Watt
Ra
e.g. N
e.g. 3 : 3W
e.g. E : Typ.65
<Marking2>
Tc measuring-point(Board side)
                       Uni t : mm
Tolerances unless otherwise specified : ±0.3
Marking1
Anode
Cathode
CathodeMark(Gray)
Resin
Marking2
Emittingarea(includingwhiteresin)
<Marking1>
×6
Protection Device
It has a pr otection device bu ilt in as a protection circu it again st static electricity.
Anode Cathode
Ref.CE-P236503/13R1(0613)
3/11
( 2 ) Electro-optical Characteristics
( Tc=25 C )
Symbol
Condition
Min.
Typ.
Max.
Unit
VFIF=350mA 8.1 9.2 9.9 V
ΦvIF=350mA 305 385 - lm
Ra IF=350mA - 65 - -
Rj-c Junction-case - 6.4 - C/W
Chromaticity coordinates ( Condition : IF=350mA ,Tc=25 C )
0
0
0
0
Note: The tolerance of measurement at our tester is VF±3% , Φ10% , Chromaticity(x,y)±0.01.
Symbol
CITILED
Name CL-L104-C3N-F
Luminous Flux
DA TA SHEET
General Color
Rendering Index
Thermal Resistance
Parameter
Forward Voltage
CITIZEN ELECTRON ICS CO.,LTD. JAPAN
x
y
x
y
0.331
0.358
0.347
0.373
0.331
0.373
0.348
0.387
0.348
0.387
0.367
0.402
0.347
0.373
0.364
0.388
0.331
0.358
0.347
0.373
x
y
x
y
0.331
0.338
0.345
0.351
0.331
0.358
0.347
0.373
0.347
0.373
0.364
0.388
0.345
0.351
0.360
0.363
0.331
0.338
0.345
0.351
x
y
x
y
0.331
0.322
0.343
0.331
0.331
0.338
0.345
0.351
0.345
0.351
0.360
0.363
0.343
0.331
0.357
0.341
NR1 NR2
Color Rank
Color Rank
NR3 NR4
Color Rank
Color Rank
NR5 NR6
Color Rank
Color Rank
x-y chart-CIE1931
NR5
NR4
NR3
NR2
NR1
NR6
0.31
0.32
0.33
0.34
0.35
0.36
0.37
0.38
0.39
0.40
0.41
0.30 0.31 0.32 0.33 0.34 0.35 0.36 0.37 0.38 0.39 0.40
x
y
Ref.CE-P236503/13R1(0613)
4/11
5. Characteristics
Forward Current vs. Forward Voltage
Forward Current vs. Relative Luminous Flux
Forward Current vs. Chromaticity Coordinate
Case Temperature vs. Chromaticity Coordinate
Symbol
CL-L104-C3N-F
CITIZEN ELECTRONICS CO.,LTD. JAPA N
DA TA SHEET
CITILED
Name
-0.020
-0.015
-0.010
-0.005
0.000
0.005
0.010
0.015
0.020
0 100 200 300 400 500 600 700
IF [mA]
Δx, Δy
Δx
Δy
Tc=25C
0%
20%
40%
60%
80%
100%
120%
140%
160%
180%
200%
0 100 200 300 400 500 600 700
IF [mA]
Relative Luminous Flux [a.u.]
Tc=25C
7.5
8.0
8.5
9.0
9.5
10.0
10.5
0 100 200 300 400 500 600 700
IF [mA]
VF [V]
Tc=25C
-0.020
-0.015
-0.010
-0.005
0.000
0.005
0.010
0.015
0.020
0 20 40 60 80 100
Tc [C]
Δx, Δy
Δx
Δy
IF=350mA
Ref.CE-P236503/13R1(0613)
5/11
Case Temperature vs. Forward Voltage
Case Temperature vs. Relative Luminous Flux
Case Temperature vs. Allowable Forward Current
Spectrum
Symbol
CITIZEN ELECTRON ICS CO.,LTD. JAPAN
CITILED
Name CL-L104-C3N-F
DA TA SHEET
7.5
8.0
8.5
9.0
9.5
10.0
0 20 40 60 80 100
Tc [C]
VF [V]
IF=350mA
0%
20%
40%
60%
80%
100%
120%
0 20 40 60 80 100
Tc [C]
Relative Luminous Flux [a.u.]
IF=350mA
0%
20%
40%
60%
80%
100%
120%
350 450 550 650 750 850
λ [nm]
Relative Emission I ntensity [a.u. ]
Tc=25C IF=350mA
0
100
200
300
400
500
600
700
800
0 25 50 75 100 125
Tc [C]
IF[mA]
Ref.CE-P236503/13R1(0613)
6/11
6. Reliability
(1) Details of the tests
(2) Judgment Criteria of Failure for Reliability Test
(Ta=25 C)
Symbol
VF
Φv
U defines the upper limit of the specified characteristics. S defines the initial value.
Symbol
CITILED
Name CL-L104-C3N-F
Test Condition
Measuring Condition
Judgment Criteria for Failure
> U × 1.1
< S × 0.85
Note: Measurement shall be taken between 2 hours and 24 hours, and the test pieces should be
IF=350mA
CITIZEN ELECTRONICS CO.,LTD. JAPA N
Total Luminous Flux
I
F
=350mA
returned to the normal ambient conditions after the completion of each test.
Thermal Shock Test 60 C, 90 %RH for 1000 hoursMoisture-proof Test 100 C × 1000 hours
High Temperature Storage Test
-40 C × 30 minutes 100 C × 30 minutes, 100 cycle
-40 C × 1000 hours
Ta=-30 C, IF=350 mA× 1000 hours(with Al-fin)
Continuous Operation Test
Measuring Item
Forward Voltage
Low Temperature Storage Test Ta=85 C, IF=350 mA× 1000 hours(with Al-fin)
Ta=60 C, IF=350 mA× 1000 hours(with Al-fin)
Test Item
DATA SHEET
Ref.CE-P236503/13R1(0613)
7/11
7. Packing Specifications
(1) Packing
An empty tray is placed on top of a five-tier tray which contain 50 pieces each. The set of six
trays is banded together with two rubber bands.
(Smallest packing unit: 250 pieces)
A label with product name, quantity, lot number is placed on the upper empty tray.
Tray (Dimensions: 310 × 210 × 11mm / Materials: Electrically conductive PS)
Symbol
CITIZEN ELECTRON ICS CO.,LTD. JAPAN
DATA SHEET
CITILED
Name CL-L104-C3N-F
< Pack ing figure >
Product 50pcs/tr ay
1. TYPE CL-L104-C3N-F
2. P.No. (Cutomer's P/N) e.g. xxx
3. Lot No. e.g. 132001
- First letter: Last digit of the year e.g. 13 : year 2013
- Second letter: Production month e.g. 2 : Feb
Note: October, November and December are designated
by X, Y and Z, respectively.
- Third letter: Control LOT including factory number
e.g. 001
4. Quantity e.g. 250 pieces
< Exam ple of indication label >
CUSTOMER
CITIZEN ELECTRONICS
ELECTRONICS
TYPE
P.NO
LOT No
Q'ty
CL-L104-C3N-F
xxx
132001
250 pcs.
---(1)
---(2)
---(3)
---(4)
PASS
Ref.CE-P236503/13R1(0613)
8
Precautions
CITIZEN ELECTRONICS CO.,LTD. JAPAN
Symbol
CITILED
Name CL-L104-C3N-F
DA TA SHEET 8/11
(1) 1. Handling with care for this product
-Both the light emitting area and white dam over the light emitting area is composed of resin materials.
Please avoid the resin area from being pressed, stressed, rubbed, come into contact with sharp metal nail
(e.g. edge of reflector part) because the function, performance and reliability of this product
are negatively impacted.
-Please be aware that this product should not come into contact with any other parts
while incorporating in your lighting apparatus or your other products.
(2) Countermeasure against static electricity
-Handling of this product needs countermeasures against static electricity
because this is a semiconductor product.
-Please take adequate measures to prevent any static electricity being produced
such as the wearing of a wristband or anti-static gloves when handling this product.
-Every manufacturing facility in regard to the product (plant, equipment, machine, carrier machine
and conveyance unit) should be connected to ground and please avoid the product to be electric-charged.
-ESD sensitivity of this product is over 1000V (HBM, based on JEITA ED-4701/304).
-After assembling the LEDs into your final product(s), it is recommended to check
whether the assembled LEDs are damaged by static electricity (electrical leak phenomenon) or not.
-It is easy to find static damaged LED dies by a light-on test with the minimum current value.
(3) Caution of product assembly
-Regarding this product assembling on the heat sink, it is recommended to use M3 screw.
It might be good for screw tightening on the heat sink to do temporary tightening and final tightening.
In addition, please dont press with excess stress on the product.
-The condition of the product assembling on the heat sink and the control of screw tightening torque
needs to be optimized according to the specification of the heat sink.
-Roughness, unevenness and burr of surface negatively impact thermal bonding
between the product and heat sink and increase heat thermal resistance between them.
Confidence of thermally and mechanical coupling between the product and heat sink are confirmed
by checking the mounting surface and measuring the case temperature of the product.
-In order to reduce the thermal resistance at assembly, it might be good to use
TIM (Thermal Interface Material) on whole contact surface of the product.
In case of using thermal grease for the TIM, it might be good to apply uniformly
on the contact surface of the product. In case of using thermal sheet for the TIM,
it might be good to make sure that the product is NOT strained by stress
when the screws are tightened for assembly.
Ref.CE-P236503/13R1(0613)
8. Precautions (continued)
Name CL-L104-C3N-F
CITIZEN ELECTRONICS CO.,LTD. JAPAN
DA TA SHEET 9/11
Symbol
CITILED
(4) Thermal Design
-The thermal design to draw heat away from the LED junction is most critical parameter
for an LED illumination system. High operating temperatures at the LED junction adversely affect
the performance of LEDs light output and lifetime. Therefore the LED junction temperature should
not exceed the absolute maximum rating in LED illumination system.
-The LED junction temperature while operation of LED illumination system depends upon
thermal resistance of internal LED package (Rj-c), outer thermal resistances of LED package,
power loss and ambient temperature. Please take both of the thermal design specifications
and ambient temperature conditions into consideration for the setting of driving conditions.
-For more information, please refer to application note "Thermal Management".
(5) Driving Current
-A constant current is recommended as an applying driving current to this product.
In the case of constant voltage driving, please connect current-limiting resistor to each products in series
and control the driving current to keep under the absolute maximum rating forward current value.
-Electrical transient might apply excess voltage, excess current and reverse voltage to the product(s).
They also affect negative impact on the product(s) therefore please make sure that no excess voltage,
excess current and reverse voltage is applied to the product(s)
when the LED driver is turn-on and/or turn-off.
-For more information, please refer to application note "Driving".
(6) Lighting at a minimum current value
-In a case where the minimum current(IF min) is applied to the product,
some of LED dice in the product might look different in their brightness
due to the individual difference of the LED dice, and they are not failed.
(7) Electrical Safety
-This product is designed and produced according to IEC 62031:2008
(IEC 62031:2008 LED modules for general lighting. Safety specification)
-Dielectric voltage withstand test has been conducted on this product to see any failure
after applying voltage between active pads and aluminum section of the product,
and to pass at least 500V.
-Considering conformity assessment for IEC62031:2008, almost all items of the specification
depend upon your final product of LED illumination system.
Therefore, please confirm with your final product for electrical safety of your product.
As well, the products comply with the criteria of IEC62031:2008 as single LED package.
Ref.CE-P236503/13R1(0613)
8. Precautions (continued)
CITIZEN ELECTRONICS CO.,LTD. JAPAN
Symbol
CITILED
Name CL-L104-C3N-F
DA TA SHEET 10/11
(9) Eye Safety
-The International Electrical Commission (IEC) published in 2006 IEC 62471
2006 Photobiological safety of lamps and lamp systems which includes LEDs within its scope.
-When sorting single LEDs according to IEC 62471, almost all white LEDs can be classified
as belonging to either Exempt Group (no hazard) or Risk Group 1 (low risk).
-However, Optical characteristics of LEDs such as radiant flux,
spectrum and light distribution are factors that affect the risk group determination of the LED,
and especially a high-power LED, that emits light containing blue wavelengths,
might have properties equivalent to those of Risk Group 2 (moderate risk).
-Great care should be taken when directly viewing an LED that is driven at high current,
has multiple uses as a module or when focusing the light with optical instruments,
as these actions might greatly increase the hazard to your eyes.
-It is recommended to regard the evaluation of stand-alone LED packages as a reference
and to evaluate your final product.
(10) This product is not designed for usage under the following conditions.
If the product might be used under the following conditions, you shall evaluate its effect
and appropriate them. In places where the product might:
-directly and indirectly get wet due to rain and/or at place with the fear.
-be damage by seawater and/or at place with the fear
-be exposed to corrosive gas (such as Cl2, H2S, NH3, SOx, NOx and so on) and/or at place with the fear.
-be exposed to dust, fluid or oil and/or at place with the fear.
(8) Recommended soldering Condition (This product is not adaptable to reflow process.)
-For manual soldering
Please use lead-free soldering.
Soldering shall be implemented using a soldering bit at a temperature lower than 350C,
and shall be finished within 3.5 seconds for one land.
No external force shall be applied to resin part while soldering is implemented.
Next process of soldering should be carried out after the product has return to ambient temperature.
-For soldering correction
Regarding soldering correction, above conditions shall be applied.
Contacts number of soldering bit should be within twice for each terminal as a correction.
* Citizen Electronics cannot guarantee if usage exceeds these recommended conditions.
Please use it after sufficient verification is carried out on your own risk if absolutely necessary.
Ref.CE-P236503/13R1(0613)
9. Precautions with regard to product use
(1) This document is provided for reference purposes only so that CITIZEN ELECTRONICS'
products are used as intended. CITIZEN ELECTRONICS neither makes warranties or
representations with respect to the accuracy or completeness of the information contained
in this document nor grants any license to any intellectual property rights or any other
rights of CITIZEN ELECTRONICS or any third party with respect to the information
in this document.
(2) All information included in this document such as product data, diagrams, charts,
is current as of the date this document is issued.
Such information, however, is subject to change without any prior notice.
Before purchasing or using any CITIZEN ELECTRONICS' products listed in this document,
please confirm the latest product information with a CITIZEN ELECTRONICS' sales office,
and formal specifications must be exchanged and signed by both parties prior to mass production.
(3) CITIZEN ELECTRONICS has used reasonable care in compiling the information
included in this document,
but CITIZEN ELECTRONICS assumes no liability whatsoever for any damages incurred as
a result of errors or omissions in the information included in this document.
(4) Absent
written signed agreement, except as provided in the relevant terms and conditions of
sale for product, and to the maximum extent allowable by law, CITIZEN ELECTRONICS
assumes no liability whatsoever, including without limitation, indirect, consequential, special,
or incidental damages or loss, including without limitation, loss of profits, loss of opportunities,
business interruption and loss of data, and disclaims any and all express or implied warranties
and conditions related to sale, use of product, or information, including warranties
or conditions of merchantability, fitness for a particular purpose, accuracy of information,
or no infringement.
(5) Though CITIZEN ELECTRONICS works continually to improve products' quality and reliability,
products can malfunction or fail. Customers are responsible for complying with safety standards
and for providing adequate designs and safeguards to minimize risk and avoid situations
in which a malfunction or failure of a product could cause loss of human life,
bodily injury or damage to property, including data loss or corruption.
In addition, customers are also responsible for determining the appropriateness of
use of any information contained in this document such as application cases not only with
evaluating by their own but also by the entire system.
CITIZEN ELECTRONICS assumes no liability for customers' product design or applications.
(6) Please contact CITIZEN ELECTRONICS' sales office if you have any questions regarding
the information contained in this document, or if you have any other inquiries.
CITIZEN Micro HumanTech is a registered trademark of Citizen Holding Co., Japan.
CITILED is a registered trademark of CITIZEN ELECTRONICS CO ., LTD. Japan
Name CL-L104-C3N-F
CITIZEN ELECTRONICS CO.,LTD. JAPAN
DA TA SHEET 11/11
Symbol
CITILED
Ref.CE-P236503/13R1(0613)