High Reliability Surface Mount Resistor MCHP Series * * * * * * * Metal GlazeTM thick film element fired at 1000C to solid ceramic substrate DESC Approved Excellent surge capability Reliable Metal GlazeTM technology Superb solderability - reflow and wave Operating temperature -55C to +150C Minimum board real estate requirements Established SPC and continuous improvement programs High temperature dielectric coating Solder over nickel barrier The MCHP High Reliability Surface Mount Resistors are part of the RG product family of precision resistors developed by IRC in 1960 to meet the stringent demands of the military market. In leaded form, these resistors are qualified to level S under MIL-R-39017 and MIL-R-55182. The MCHP resistor utilizes the core element from this series, but with modified contacts and encapsulation. The MCHP High Reliability Surface Mount Resistors are in compliance to DESC drawings 85083 (MCHP 1/8) and 87037 (MCHP 1) and are supplied in accordance tot he requirements of MIL-R-55342. Under this specification, all resistors are subjected to "Thermal Shock". Samples are selected from each lot and tested to "TCR", "STOL", "Terminal adhesion", "Solderability", and "Visual" to ensure the lot is in conformance to specified requirements. Electrical Data Size Code Industry Footprint IRC Type DESC Drawing Rated Power (watts) Working Voltage Maximum Voltage Resistance Range (ohms) Tolerance (%) TCR (ppm/C) B 1206 MCHP 1/8 950114 0.125 @ 70C 200 400 0.1 to 1.0M 1, 2, 5 100 D 2010 MCHP 1/2 94048 0.5 @ 70C 300 600 0.1 to 1.6M 1, 2, 5 100 5 F 2512 MCHP 1 95006 1.0 @ 70C 350 700 0.1 to 2.2M 1, 2, 5 100 H 3610 MCHP 2 94047 2.0 @ 25C 500 1000 0.2 to 2.2M 1, 2, 5 100 See page 8 for product dimensions, recommended solder pads, and standard packaging. For operation above 70C, use power derating curve. Not to exceed P x R 4 Formerly 85083 5 Formerly 87037 Power Derating Curve 120 % of Rated Power 100 95 00 6, 80 60 40 94 04 7 95 01 1, 94 04 8, 20 0 25 35 45 55 65 75 85 95 105 115 125 135 145 30 40 50 60 70 80 90 100 110 120 130 140 150 Ambient Temperature (C) General Note IRC reserves the right to make changes in product specification without notice or liability. All information is subject to IRC's own data and is considered accurate at time of going to print. (c) IRC Wire and Film Technologies Division * 4222 South Staples Street * Corpus Christi Texas 78411 USA Telephone: 361 992 7900 * Facsimile: 361 992 3377 * Website: www.irctt.com A subsidiary of TT electronics plc MCHP Series Issue September 2008 Sheet 1 of 2 High Reliability Surface Mount Resistor IRC Advanced Film Division Environmental Data Characteristics Temperature Coefficient Maximum Change 100 ppm/C Test Method MIL-R-55342E Par 4.7.9 (-55C + 125C) Thermal Shock 0.5% + 0.01 ohm MIL-R-55342E Par 4.7.3 (-65C + 150C, 5 cycles) Low Temperature Operation 0.25% + 0.01 ohm MIL-R-55342E Par 4.7.4 (-65C @ working voltage) Short Time Overload 0.25% + 0.01 ohm 1% for R>100K ohm MIL-R-55342E Par 4.7.5 2.5 x P x R for 5 seconds High Temperature Exposure 0.5% + 0.01 ohm MIL-R-55342E Par 4.7.6 (+150C for 100 hours) Resistance to Bonding Exposure 0.25% + 0.01 ohm MIL-R-55342E Par 4.7.7 (Reflow soldered to board at 260C for 10 seconds) Solderability 95% minimum coverage MIL-STD-202, Method 208 (245C for 5 seconds) Moisture Resistance 0.5% 0.01 ohm MIL-R-55342E Par 4.7.8 (10 cycles, total 240 hours) Life Test 0.5% 0.01 ohm MIL-R-55342E Par 4.7.10 (2000 hours at 70C intermittent) Terminal Adhesion Strength 1% + 0.01 ohm no mechanical damage 1200 gram push from underside of mounted chip for 60 seconds Resistance to Board Bending 1% + 0.01 ohm no mechanical damage Chip mounted in center of 90mm long board, deflected 5mm so as to exert pull on chip contacts for 10 seconds Ordering Data Sample Part No. 95011 - 2213 - F - 13 DESC Drawing Number (CHP 1/8, CHP 1/2, CHP 1, or CHP 2) Resistance Value (100 ohms and greater - First 3 significant digits plus 4th digit multiplier) Example: 100 ohms = 1000, 1000 ohms = 1001, 150,000 ohms = 1503 (Less than 100 ohms - "R" is used to designate decimal) Example: 51 ohms = 51R0, 1.6 ohm = 1R60, 0.25 ohms = R250 Tolerance (F = 1.0%; G = 2.0%; J = 5.0%) Packaging Code* (BLK = Bulk, 7 = 7" Reel, 13 = 13" Reel) (c) IRC Wire and Film Technologies Division * 4222 South Staples Street * Corpus Christi Texas 78411 USA Telephone: 361 992 7900 * Facsimile: 361 992 3377 * Website: www.irctt.com MCHP Series Issue September 2008 Sheet 2 of 2