3M
Interconnect Solutions
http://www.3M.com/interconnects/
3M is a trademark of 3M Company.
For technical, sales or ordering information call
800-225-5373
3M™ MetPak™ CP2 Press-Fit Socket
2 mm Type B, 95, 110 and 125 Signal Contacts, Right Angle CP2 Series
Physical
Mechanical
Electrical
Environmental
PCB Data
CompactPCI is a registered trademark of PICMG-PCI Industrial Computer Manufacturers Group, Inc.
MetPak is a trademark of 3M Company.
Insulation Material: Glass Filled Polyester (PBT)
Insulation Flammability: UL 94 V-0
Contact Material: Copper Alloy
Plating
Underplate: 50 μ" [ 1.27 μm ] Nickel
Wiping Area: 30 μ″ [ 0.76 μm ] Gold
Termination Area: 100 μ" [ 2.54 μm ] Tin Lead
Mating Force: 0.75 N/contact maximum
Withdrawal Force: 0.15 N/contact minimum
Insulation Resistance: 10G Ω (Minimum)
Current Ratings: 1A at +70°C
Test Voltage: 750 VAC
Temperature Ratings: -55°C to +125°C
Recommended PCB hole platings: Cu: .0250 - .050 mm [.001 - .002 in.] and Sn or Sn/Pb: <10 µm [400 µ"]
PCB thickness: 1.4 - 5.6 mm [.06 - .22 in.]
Press-In Force: 26 ± 6N/pin on nominal hole diameter Ø 0.6 ± 0.05 mm [Ø .024 ± .002 in.]
Retention Force: 20 ± 5N/pin on nominal hole diameter Ø 0.6 ± 0.05 mm [Ø .024 ± .002 in.]
TS-2032-04
Sheet 1 of 2
Date Modified: April 11, 2007
• 25 mm basic system unit
• 38, 44 and 50 mm module
• CompactPCI® combines the benefits of PCI desktop
architecture with the ruggedness of the 3U and 6U IEEE
Eurocard form factor popularized by the VME bus
• Designed according to IEC 61076-4-101
and IEC 917 standards
• Meets CPCI application requirements
• “Eye of the Needle” compliant pin press-fit design
reduces manufacturing time and cost
• 2 mm grid spacing allows for high signal density
at low cost
• Additional grounding rows available for improved
ground bounce and EMI immunity
• See Regulatory Information Appendix (RIA)
for chemical compliance information
UL File No.: E68080
DISCONTINUED,
Superseded by TS-2268-A
3M
Interconnect Solutions
http://www.3M.com/interconnects/
3M is a trademark of 3M Company.
For technical, sales or ordering information call
800-225-5373
20.20
.795
11.40
.449
8.80
.346
7.70
.303
DIM. "A" MAX.
11.40
.449
DIM. "B"
8.00
.315
2.00
.079
TYP.
2.00
.079 TYP.
A
E
D
C
B
1357911151719212325
.95
.037
TYP.
7.25
.285
2.00
.079 TYP.
2.00
.079 9.40
.370
3.50
.138
13
3M™ MetPak™ CP2 Press-Fit Socket
2 mm Type B, 95, 110 and 125 Signal Contacts, Right Angle CP2 Series
CP2-GS XXX - L
CP2 - SB XXX - X 1 - TG30
Number of Signal Contacts
095, 110 and 125
Shield Options:
G=Upper Shield
Blank = No Shield
Connector Type:
B19 (95 Signal Contacts)
B22 (110 Signal Contacts)
B25 (125 Signal Contacts)
Lower Shield (Order Separately)
Ordering Information
Signal Contact
Quantity Dimension A Dimension B
95 38.00 [1.496] 36.00 [1.417]
110 44.00 [1.732] 42.00 [1.653]
125 50.00 [1.968] 48.00 [1.890]
Wiping Area = Gold plating
Press-Fit Tails = Tin-Lead plating
(RIA E2 & C2 apply
Tin-Lead plated contacts
(RIA E2 & C2 apply)
TS-2032-04
Sheet 2 of 2
Recommended PCB hole mounting pattern
Connector side
lO0.10 MAB
A
B
C
D
E
1
F
357911
151719212325
DIM. "B"
10.00
.394
2.00
.079
TYP.
1.50
.059
A
B
O.60 ±.05
.024 ±.002
PLATED HOLES
2.00
.079 TYP.
13
.0 .00 .000
mm ±2.5 ±.25 ±.025
Tolerance Unless Noted
mm
[inch]
[ ] Dimensions for Reference
Only
DISCONTINUED,
Superseded by TS-2268-A
Regulatory Information Appendix
3M Electronic Solutions Division/Interconnect
EUROPE
Appendix E1: European Union RoHS
Directive 2002/95/EC, Restriction of the Use of Certain Hazardous Substances in Electrical & Electronic Equipment, as
amended by EU Commission Decision 2005/618/EC.
This product is RoHS Compliant 2005/95/EC.
“RoHS Compliant 2005/95/EC” means that the product or part (“Product”) does not contain any of the substances in
excess of the maximum concentration values in EU Directive 2002/95/EC, as amended by Commission Decision 2005/618/
EC, unless the substance is in an application that is exempt under EU RoHS. Unless otherwise stated by 3M in writing, this
information represents 3M’s best knowledge and belief based upon information provided by third party suppliers to 3M.
In the event any product is proven not to conform with 3M’s Regulatory Information Appendix, then 3M’s entire liability
and Buyer’s exclusive remedy will be in accordance with the Warranty stated below.
Appendix E2: European Union RoHS
Directive 2002/95/EC, Restriction of the Use of Certain Hazardous Substances in Electrical & Electronic Equipment, as
amended by EU Commission Decision 2005/618/EC
This product contains lead in the compliant pin area in excess of the maximum concentration value allowed but is
compliant by exemption under EU Commission Decision 2005/747/EC.
“RoHS Compliant 2005/95/EC” means that the product or part (“Product”) does not contain any of the substances in
excess of the maximum concentration values in EU Directive 2002/95/EC, as amended by Commission Decision 2005/618/
EC, unless the substance is in an application that is exempt under EU RoHS. Unless otherwise stated by 3M in writing, this
information represents 3M’s best knowledge and belief based upon information provided by third party suppliers to 3M.
In the event any product is proven not to conform with 3M’s Regulatory Information Appendix, then 3M’s entire liability
and Buyer’s exclusive remedy will be in accordance with the Warranty stated below.
Appendix E3: European Union RoHS
Directive 2002/95/EC, Restriction of the Use of Certain Hazardous Substances in Electrical & Electronic Equipment as
amended by Commission Decision 2005/618/EC.
This product contains lead in the solder tail area in excess of the maximum concentration value allowed.
Unless otherwise stated by 3M in writing, this information represents 3M’s best knowledge and belief based upon
information provided by third party suppliers to 3M.
In the event any product is proven not to conform with 3M’s Regulatory Information Appendix, then 3M’s entire liability
and Buyer’s exclusive remedy will be in accordance with the Warranty stated below.
Appendix E4: European Union RoHS
Directive 2002/95/EC, Restriction of the Use of Certain Hazardous Substances in Electrical & Electronic Equipment, as
amended by EU Commission Decision 2005/618/EC.
This product contains decaBDE in the insulating material in excess of the maximum concentration value allowed but is
compliant by exemption under EU Commission Decision 2005/17/EC.
“RoHS Compliant 2005/95/EC” means that the product or part (“Product”) does not contain any of the substances in
excess of the maximum concentration values in EU Directive 2002/95/EC, as amended by Commission Decision
2005/618/EC, unless the substance is in an application that is exempt under EU RoHS. Unless otherwise stated by 3M in
writing, this information represents 3M’s best knowledge and belief based upon information provided by third party
suppliers to 3M.
In the event any product is proven not to conform with 3M’s Regulatory Information Appendix, then 3M’s entire liability
and Buyer’s exclusive remedy will be in accordance with the Warranty stated below.
RIA-2217-B
DISCONTINUED,
Superseded by TS-2268-A
CHINA
Appendix C1: China RoHS
Electronic Industry Standard of the People’s Republic of China, SJ/T11363-2006, Requirements for Concentration Limits
for Certain Hazardous Substances in Electronic Information Products.
This symbol, per Marking for the Control of Pollution Caused by Electronic Information Products, SJ/T11364-2006,
means that the product or part does not contain any of the following substances in excess of the following maximum
concentration values in any homogeneous material: (a) 0.1% (by weight) for lead, mercury, hexavalent chromium,
polybrominated biphenyls or polybrominated diphenyl ethers; or (b) 0.01% (by weight) for cadmium. Unless otherwise
stated by 3M in writing, this information represents 3M’s best knowledge and belief based upon information provided by
third party suppliers to 3M.
In the event any product is proven not to conform with 3M’s Regulatory Information Appendix, then 3M’s entire liability
and Buyer’s exclusive remedy will be in accordance with the Warranty stated below.
Appendix C2: China RoHS
20
Electronic Industry Standard of the People’s Republic of China, SJ/T11363-2006, Requirements for Concentration Limits
for Certain Hazardous Substances in Electronic Information Products.
This symbol, per Marking for the Control of Pollution Caused by Electronic Information Products, SJ/T11364-2006,
means that the product or part does contain a substance, as detailed in the chart below, in excess of the following
maximum concentration values in any homogeneous material: (a) 0.1% (by weight) for lead, mercury, hexavalent
chromium, polybrominated biphenyls or polybrominated diphenyl ethers; or (b) 0.01% (by weight) for cadmium. Unless
otherwise stated by 3M in writing, this information represents 3M’s best knowledge and belief based upon information
provided by third party suppliers to 3M.
The numerical reference in the symbol above should not be construed as a representation regarding the product’s life or an
extension of a product warranty. The product warranty is stated below. In the event any product is proven not to conform
with 3M’s Regulatory Information Appendix, then 3M’s entire liability and Buyer’s exclusive remedy will be in
accordance with the product Warranty stated below.
Important Notice
All statements, technical information, and recommendations related to 3M’s products are based on information believed to be reliable, but the
accuracy or completeness is not guaranteed. Before using this product, you must evaluate it and determine if it is suitable for your intended
application. You assume all risks and liability associated with such use. Any statements related to the product which are not contained in 3M’s
current publications, or any contrary statements contained on your purchase order shall have no force or effect unless expressly agreed upon, in
writing, by an authorized officer of 3M.
Warranty; Limited Remedy; Limited Liability.
This product will be free from defects in material and manufacture for a period of one (1) year from the time of purchase. 3M MAKES NO OTHER
WARRANTIES INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A
PARTICULAR PURPOSE. If this product is defective within the warranty period stated above, your exclusive remedy shall be, at 3M’s option, to
replace or repair the 3M product or refund the purchase price of the 3M product. Except where prohibited by law, 3M will not be liable for any
indirect, special, incidental or consequential loss or damage arising from this 3M product, regardless of the legal theory asserted.
3
Electronic Solutions Division
6801 River Place Blvd.
Austin, TX 78726-9000
800/225-5373
www.3M.com/interconnects RIA-2217-B
© 3M 2007
Name and Content of Hazardous Substances or Elements
DISCONTINUED,
Superseded by TS-2268-A
