General Description
The MAX16060/MAX16061/MAX16062 are 1% accurate,
quad-/hex-/octal-voltage µP supervisors in a small thin
QFN package. These devices provide supervisory func-
tions for complex multivoltage systems. The MAX16060
monitors four voltages, the MAX16061 monitors six volt-
ages, and the MAX16062 monitors eight voltages.
These devices offer independent outputs for each mon-
itored voltage along with a reset output that asserts
whenever any of the monitored voltages fall below their
respective thresholds (down to 0.4V) or the manual
reset input is asserted. The reset output remains assert-
ed for the reset timeout after all voltages are above their
respective thresholds and the manual reset input is
deasserted. The minimum reset timeout is internally set
to 140ms or can be adjusted with an external capacitor.
All open-drain outputs have internal 30µA pullups that
eliminate the need for external pullup resistors.
However, each output can be driven with an external
voltage up to 5.5V. Other features offered include a
manual reset input, a tolerance pin for selecting 5% or
10% input thresholds, and a margin enable function for
deasserting the outputs during margin testing.
An additional feature is a watchdog timer that asserts
RESET when the watchdog timeout period (1.6s typ) is
exceeded. The watchdog timer can be disabled by
leaving WDI unconnected.
These devices are offered in 16-, 20-, and 24-pin thin
QFN packages (4mm x 4mm) and are fully specified
from -40°C to +125°C.
Features
oFixed Thresholds for 3.3V, 2.5V, and 1.8V Systems
oAdjustable Thresholds Monitor Low Voltages
(Down to 0.4V)
o1% Accurate over Temperature
oOpen-Drain Outputs with Internal Pullups Reduce
the Number of External Components
oFixed 140ms (min) or Capacitor-Adjustable Reset
Timeout
oManual Reset, Margin Enable, and Tolerance
Select Inputs
oWatchdog Timer
1.6s (typ) Timeout Period
54s Startup Delay After Reset
oMonitors Four (MAX16060), Six (MAX16061), or
Eight (MAX16062) Voltages
oRESET Output Indicates All Voltages Present
oIndependent Voltage Monitors
oGuaranteed to Remain Asserted Down to VCC = 1V
oSmall (4mm x 4mm) Thin QFN Package
MAX16060/MAX16061/MAX16062
1% Accurate, Quad-/Hex-/Octal-Voltage
µP Supervisors
________________________________________________________________________________________________________________________________
Maxim Integrated Products
1
MAX16061A
GND
μP
TOL
VCC SRT
MR
IN1
MARGIN
VIN1
VIN2
VIN3
VIN4
VIN5
VIN6
RESET
WDI
OUT1
RST
I/O
IN2
IN3
IN4
IN5
IN6
OUT2
OUT3
OUT4
OUT5
OUT6
Ordering Information
Typical Operating Circuit
19-4099; Rev 0; 4/08
For pricing, delivery, and ordering information, please contact Maxim Direct at 1-888-629-4642,
or visit Maxim’s website at www.maxim-ic.com.
Note: The “_” is a placeholder for the input voltage threshold.
See Table 1. The MAX16060/MAX16061/MAX16062 are avail-
able in factory-preset thresholds/configuration combinations.
Choose the desired combination and complete part number
from Table 1.
+
Denotes a lead-free package.
For tape-and-reel, add a “T” after the “+.” Tape-and-reel are
offered in 2.5k increments.
*
EP = Exposed pad.
PART TEMP RANGE PIN-PACKAGE
MAX16060_TE+ -40°C to +125°C 16 TQFN-EP*
MAX16061_TP+ -40°C to +125°C 20 TQFN-EP*
MAX16062_TG+ -40°C to +125°C 24 TQFN-EP*
Storage Equipment
Servers
Networking/Telecommun-
ication Equipment
Multivoltage ASICs
Automotive
Applications
MAX16060/MAX16061/MAX16062
1% Accurate, Quad-/Hex-/Octal-Voltage
µP Supervisors
2______________________________________________________________________________________________________________________________________________________________________________
ABSOLUTE MAXIMUM RATINGS
ELECTRICAL CHARACTERISTICS
(VCC = 2.0V to 5.5V, TA= -40°C to +125°C, unless otherwise specified. Typical values are at VCC = 3.3V, TA= +25°C.) (Note 1)
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
VCC, OUT_, IN_, RESET to GND ..............................-0.3V to +6V
TOL, MARGIN, MR, SRT, WDI to GND ...........-0.3V to VCC + 0.3
Input/Output Current (RESET, MARGIN,
SRT, MR, TOL, OUT_, WDI).........................................±20mA
Continuous Power Dissipation (TA= +70°C)
16-Pin TQFN (derate 16.9mW/°C above +70°C) ......1349mW
20-Pin TQFN (derate 16.9mW/°C above +70°C) ......1355mW
24-Pin TQFN (derate 16.9mW/°C above +70°C) ......1666mW
Operating Temperature Range .........................-40°C to +125°C
Junction Temperature .....................................................+150°C
Storage Temperature Range .............................-65°C to +150°C
Lead Temperature (soldering, 10s) .................................+300°C
PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS
Operating Voltage Range VCC (Note 2) 1.0 5.5 V
VCC = 3.3V, OUT_, RESET not asserted 45 65
Supply Current (Note 3) ICC VCC = 5V, OUT_, RESET not asserted 50 70 µA
UVLO (Undervoltage Lockout) VUVLO VCC rising 1.62 1.80 1.98 V
UVLO Hysteresis VUVLO_HYS 65 mV
IN_ (See Table 1)
3.3V threshold, TOL = GND 3.069 3.102 3.135
3.3V threshold, TOL = VCC 2.904 2.937 2.970
2.5V threshold, TOL = GND 2.325 2.350 2.375
2.5V threshold, TOL = VCC 2.200 2.225 2.250
1.8V threshold, TOL = GND 1.674 1.692 1.710
Threshold Voltages (IN_ Falling) VTH
1.8V threshold, TOL = VCC 1.584 1.602 1.620
V
TOL = GND 0.390 0.394 0.398
Adjustable Threshold
(IN_ Falling) VTH TOL = VCC 0.369 0.373 0.377 V
IN_ Hysteresis VTH_HYS IN_ rising 0.5 % VTH
Fixed thresholds 3 16 µA
IN_ Input Current Adjustable thresholds -100 +100 nA
MAX16060/MAX16061/MAX16062
1% Accurate, Quad-/Hex-/Octal-Voltage
µP Supervisors
______________________________________________________________________________________________________________________________________________________________________________3
ELECTRICAL CHARACTERISTICS (continued)
(VCC = 2.0V to 5.5V, TA= -40°C to +125°C, unless otherwise specified. Typical values are at VCC = 3.3V, TA= +25°C.) (Note 1)
PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS
RESET
SRT = VCC 140 200 280
CSRT = 1500pF (Note 4) 2.43 3.09 3.92
CSRT = 100pF 0.206
ms
Reset Timeout tRP
CSRT = open 50 µs
SRT Ramp Current ISRT VSRT = 0V 460 600 740 nA
SRT Threshold 1.173 1.235 1.293 V
SRT Hysteresis 100 mV
IN_ to Reset Delay tRD IN_ falling 20 µs
V
C C
= 3.3V , IS IN K = 10m A, RESET asser ted 0.3
VCC = 2.5V, ISINK = 6mA, RESET asser ted 0.3RESET Output-Voltage Low VOL
VCC = 1.2V, ISINK = 50µA, RESET asser ted 0.3
V
RESET Output-Voltage High VOH VCC 2.0V, ISOURCE = 6µA, RESET
deasserted
0.8 x
VCC V
MR Input-Voltage Low VIL 0.3 x
VCC V
MR Input-Voltage High VIH 0.7 x
VCC V
MR Minimum Pulse Width s
MR Glitch Rejection 100 ns
MR to Reset Delay 200 ns
MR Pullup Resistance Pulled up to VCC 12 20 28 kΩ
OUTPUTS (OUT_ )
VCC = 3.3V, ISINK = 2mA 0.3
OUT_ Output-Voltage Low VOL VCC = 2.5V, ISINK = 1.2mA 0.3 V
OUT_ Output-Voltage High VOH VCC 2.0V, ISOURCE = 6µA 0.8 x
VCC V
IN_ to OUT_ Propagation Delay tD(VTH + 100mV) to (VTH - 100mV) 20 µs
MAX16060/MAX16061/MAX16062
1% Accurate, Quad-/Hex-/Octal-Voltage
µP Supervisors
4______________________________________________________________________________________________________________________________________________________________________________
PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS
WATCHDOG TIMER
WDI Input-Voltage Low VIL 0.3 x
VCC V
WDI Input-Voltage High VIH 0.7 x
VCC V
WDI Pulse Width (Note 5) 50 ns
Watchdog Timeout Period tWDI 1.12 1.60 2.40 s
Watchdog Startup Period 35 54 72 s
Watchdog Input Current VWDI = 0 to VCC (Note 5) -1 +1 µA
DIGITAL LOGIC
TOL Input-Voltage Low VIL 0.3 x
VCC V
TOL Input-Voltage High VIH 0.7 x
VCC V
TOL Input Current TOL = VCC 100 nA
MARGIN Input-Voltage Low VIL 0.3 x
VCC V
MARGIN Input-Voltage High VIH 0.7 x
VCC V
MARGIN Pullup Resistance Pulled up to VCC 12 20 28 kΩ
MARGIN Delay Time tMD Rising or falling (Note 6) 50 µs
ELECTRICAL CHARACTERISTICS (continued)
(VCC = 2.0V to 5.5V, TA= -40°C to +125°C, unless otherwise specified. Typical values are at VCC = 3.3V, TA= +25°C). (Note 1)
Note 1: Devices are tested at TA= +25°C and guaranteed by design for TA= TMIN to TMAX.
Note 2: The outputs are guaranteed to remain asserted down to VCC = 1V.
Note 3: Measured with WDI, MARGIN, and MR unconnected.
Note 4: The minimum and maximum specifications for this parameter are guaranteed by using the worst case of the SRT ramp cur-
rent and SRT threshold specifications.
Note 5: Guaranteed by design and not production tested.
Note 6: Amount of time required for logic to lock/unlock outputs from margin testing.
Typical Operating Characteristics
(VCC = 3.3V, TA = +25°C, unless otherwise noted.)
SUPPLY CURRENT vs. SUPPLY VOLTAGE
SUPPLY VOLTAGE (V)
SUPPLY CURRENT (μA)
MAX16060/1/2 toc01
1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5
30
35
40
45
50
55
60
WDI, MARGIN, AND MR UNCONNECTED
SUPPLY CURRENT vs. TEMPERATURE
TEMPERATURE (°C)
SUPPLY CURRENT (μA)
MAX16060/1/2 toc02
-40 -25 -10 5 20 35 50 65 80 95 110 125
30
35
40
45
50
55
60
WDI, MARGIN, AND MR UNCONNECTED
VCC = 2.5V
VCC = 3.3V
VCC = 5V
NORMALIZED THRESHOLD
vs. SUPPLY VOLTAGE
SUPPLY VOLTAGE (V)
NORMALIZED THRESHOLD
MAX16060/1/2 toc03
1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5
0.9900
0.9925
0.9950
0.9975
1.0000
1.0025
1.0050
1.0075
1.0100
NORMALIZED THRESHOLD
vs. TEMPERATURE
TEMPERATURE (°C)
NORMALIZED THRESHOLD
MAX16060/1/2 toc04
-40 -25 -10 5 20 35 50 65 80 95 110 125
0.995
0.996
0.997
0.998
0.999
1.000
1.001
OUTPUT VOLTAGE vs. SINK CURRENT
SINK CURRENT (mA)
VOUT_ (mV)
MAX16060/1/2 toc05
012345678
0
25
50
75
100
OUT_ LOW
OUTPUT VOLTAGE vs. SOURCE CURRENT
SOURCE CURRENT (μA)
VCC - VOUT_ (mV)
MAX16060/1/2 toc06
0 5 10 15 20 25 30
0
200
400
600
800
1000
OUT_ HIGH
RESET TIMEOUT PERIOD
vs. TEMPERATURE
TEMPERATURE (°C)
RESET TIMEOUT PERIOD (ms)
MAX16060/1/2 toc08
-40 -25 -10 5 20 35 50 65 80 95 110 125
190
191
192
193
194
195
196
197
198
1 10 100 1000
MAXIMUM TRANSIENT DURATION
vs. INPUT OVERDRIVE
MAX16060/1/2 toc07
INPUT OVERDRIVE (mV)
MAXIMUM TRANSIENT DURATION (μs)
600
0
100
200
300
400
500
OUTPUT GOES LOW
ABOVE THIS LINE
RESET TIMEOUT DELAY
MAX16060/1/2 toc09
OUT1
2V/div
IN1
5V/div
40ms/div
RESET
2V/div
SRT = VCC
MAX16060/MAX16061/MAX16062
1% Accurate, Quad-/Hex-/Octal-Voltage
µP Supervisors
_______________________________________________________________________________________
5
Typical Operating Characteristics (continued)
(VCC = 3.3V, TA = +25°C, unless otherwise noted.)
MARGIN DISABLE FUNCTION
MAX16060/1/2 toc13
OUT_
2V/div
MARGIN
2V/div
100μs/div
RESET
2V/div
OUT_ AND RESET ARE BELOW RESPECTIVE
THRESHOLDS
WATCHDOG TIMEOUT PERIOD
vs. TEMPERATURE
TEMPERATURE (°C)
WATCHDOG TIMEOUT PERIOD (s)
MAX16060/1/2 toc11
-40 -25 -10 5 20 35 50 65 80 95 110 125
1.50
1.51
1.52
1.53
1.54
1.55
1.56
1.57
1.58
1.59
1.60
MARGIN ENABLE FUNCTION
MAX16060/1/2 toc12
OUT_
2V/div
MARGIN
2V/div
100μs/div
RESET
2V/div
OUT_ AND RESET ARE
BELOW RESPECTIVE
THRESHOLDS
1000
0.01 0.1 1 10 100 1000
100
10
1
0.1
0.01
RESET TIMEOUT PERIOD
vs. CSRT
MAX16060/1/2 toc10
CSRT (nF)
tRP (ms)
MAX16060/MAX16061/MAX16062
1% Accurate, Quad-/Hex-/Octal-Voltage
µP Supervisors
6______________________________________________________________________________________________________________________________________________________________________________
MAX16060/MAX16061/MAX16062
1% Accurate, Quad-/Hex-/Octal-Voltage
µP Supervisors
______________________________________________________________________________________________________________________________________________________________________________7
Pin Description (MAX16060)
PIN NAME FUNCTION
1 IN3 Monitored Input Voltage 3. See Table 1 for the input voltage threshold.
2 IN4 Monitored Input Voltage 4. See Table 1 for the input voltage threshold.
3 WDI
Watchdog Timer Input. If WDI remains low or high for longer than the watchdog timeout period, RESET
is asserted. The timer clears whenever a reset is asserted or a rising or falling edge on WDI is detected.
The watchdog timer enters a startup period that allows 54s for the first transition to occur before a reset.
Leave WDI unconnected to disable the watchdog timer. The WDI unconnected-state detector uses a
small 400nA current. Therefore, do not connect WDI to anything that will source or sink more than
200nA. Note that the leakage current specification for most three-state drivers exceeds 200nA.
4 GND Ground
5V
CC Unmonitored Power-Supply Input
6 OUT3 O utp ut 3. When the vol tag e at IN 3 fal l s b el ow i ts thr eshol d , OU T3 g oes l ow and stays l ow unti l the vol tag e at
IN 3 exceed s i ts thr eshol d . The op en- d r ai n outp ut has a 3A i nter nal p ul l up to V
C C
.
7 OUT4 O utp ut 4. When the vol tag e at IN 4 fal l s b el ow i ts thr eshol d , OU T4 g oes l ow and stays l ow unti l the vol tag e at
IN 4 exceed s i ts thr eshol d . The op en- d r ai n outp ut has a 3A i nter nal p ul l up to V
C C
.
8MR Active-Low Manual Reset Input. Pull MR low to assert RESET low. RESET remains low for the reset
timeout period after MR is deasserted. MR is pulled up to VCC through a 20kΩ resistor.
9 SRT
Set Reset Timeout Input. Connect a capacitor from SRT to GND to set the reset timeout period. The reset
timeout period can be calculated as follows:
Reset Timeout (s) = 2.06 x 106 (Ω) x CSRT (F). For the internal timeout period of 140ms (min), connect
SRT to VCC.
10 MARGIN Active-Low Manual Deassert Input. Pull MARGIN low to deassert all outputs (go into high state),
regardless of the voltage at any monitored input.
11 OUT2 O utp ut 2. When the vol tag e at IN 2 fal l s b el ow i ts thr eshol d , OU T2 g oes l ow and stays l ow unti l the vol tag e at
IN 2 exceed s i ts thr eshol d . The op en- d r ai n outp ut has a 3A i nter nal p ul l up to V
C C
.
12 OUT1 O utp ut 1. When the vol tag e at IN 1 fal l s b el ow i ts thr eshol d , OU T1 g oes l ow and stays l ow unti l the vol tag e at
IN 1 exceed s i ts thr eshol d . The op en- d r ai n outp ut has a 3A i nter nal p ul l up to V
C C
.
13 RESET
Active-Low Reset Output. RESET asserts low when any of the monitored voltages falls below its
respective threshold or MR is asserted. RESET remains asserted for the reset timeout period after all
monitored voltages exceed their respective thresholds and MR is deasserted. This open-drain output
has a 30µA internal pullup.
14 IN1 Monitored Input Voltage 1. See Table 1 for the input voltage threshold.
15 IN2 Monitored Input Voltage 2. See Table 1 for the input voltage threshold.
16 TOL Threshold Tolerance Input. Connect TOL to GND to select 5% threshold tolerance. Connect TOL to VCC
to select 10% threshold tolerance.
—EP
Exposed Pad. EP is internally connected to GND. Connect EP to the ground plane to provide a low
thermal resistance path from the IC junction to the PCB. Do not use as the electrical connection to GND.
MAX16060/MAX16061/MAX16062
1% Accurate, Quad-/Hex-/Octal-Voltage
µP Supervisors
8______________________________________________________________________________________________________________________________________________________________________________
Pin Description (MAX16061)
PIN NAME FUNCTION
1 IN4 Monitored Input Voltage 4. See Table 1 for the input voltage threshold.
2 IN5 Monitored Input Voltage 5. See Table 1 for the input voltage threshold.
3 IN6 Monitored Input Voltage 6. See Table 1 for the input voltage threshold.
4 WDI
Watchdog Timer Input. If WDI remains low or high for longer than the watchdog timeout period, RESET is
asserted and the timer is cleared. The timer also clears whenever a reset is asserted or a rising or falling
edge on WDI is detected. The watchdog timer enters a startup period that allows 54s for the first transition to
occur before a reset. Leave WDI unconnected to disable the watchdog timer.
The WDI unconnected-state detector uses a small 400nA current. Therefore, do not connect WDI to anything
that will source or sink more than 200nA. Note that the leakage current specification for most three-state
drivers exceeds 200nA.
5 GND Ground
6V
CC Unmonitored Power-Supply Input
7 OUT4 Output 4. When the voltage at IN4 falls below its threshold, OUT4 goes low and stays low until the voltage at
IN4 exceeds its threshold. The open-drain output has a 30µA internal pullup to VCC.
8 OUT5 Output 5. When the voltage at IN5 falls below its threshold, OUT5 goes low and stays low until the voltage at
IN5 exceeds its threshold. The open-drain output has a 30µA internal pullup to VCC.
9 OUT6 Output 6. When the voltage at IN6 falls below its threshold, OUT6 goes low and stays low until the voltage at
IN6 exceeds its threshold. The open-drain output has a 30µA internal pullup to VCC.
10 MR Active-Low Manual Reset Input. Pull MR low to assert RESET low. RESET remains low for the reset timeout
period after MR is deasserted. MR is pulled up to VCC through a 20kΩ resistor.
11 SRT
Set Reset Timeout Input. Connect a capacitor from SRT to GND to set the reset timeout period. The reset
timeout period can be calculated as follows:
Reset Timeout (s) = 2.06 x 106 (Ω) x CSRT (F). For the internal timeout period of 140ms (min), connect SRT to
VCC.
12 MARGIN Manual Deassert Input. Pull MARGIN low to deassert all outputs (go into high state), regardless of the voltage
at any monitored input.
13 OUT3 Output 3. When the voltage at IN3 falls below its threshold, OUT3 goes low and stays low until the voltage at
IN3 exceeds its threshold. The open-drain output has a 30µA internal pullup to VCC.
14 OUT2 Output 2. When the voltage at IN2 falls below its threshold, OUT2 goes low and stays low until the voltage at
IN2 exceeds its threshold. The open-drain output has a 30µA internal pullup to VCC.
15 OUT1 Output 1. When the voltage at IN1 falls below its threshold, OUT1 goes low and stays low until the voltage at
IN1 exceeds its threshold. The open-drain output has a 30µA internal pullup to VCC.
16 RESET
Active-Low Reset Output. RESET asserts low when any of the monitored voltages falls below its respective
threshold or MR is asserted. RESET remains asserted for the reset timeout period after all monitored voltages
exceed their respective thresholds and MR is deasserted. This open-drain output has a 30µA internal pullup.
17 IN1 Monitored Input Voltage 1. See Table 1 for the input voltage threshold.
18 IN2 Monitored Input Voltage 2. See Table 1 for the input voltage threshold.
19 IN3 Monitored Input Voltage 3. See Table 1 for the input voltage threshold.
20 TOL Threshold Tolerance Input. Connect TOL to GND to select 5% threshold tolerance. Connect TOL to VCC to
select 10% threshold tolerance.
—EP
Exposed Pad. EP is internally connected to GND. Connect EP to the ground plane to provide a low thermal
resistance path from the IC junction to the PCB. Do not use as the electrical connection to GND.
MAX16060/MAX16061/MAX16062
1% Accurate, Quad-/Hex-/Octal-Voltage
µP Supervisors
______________________________________________________________________________________________________________________________________________________________________________9
PIN NAME FUNCTION
1 IN5 Monitored Input Voltage 5. See Table 1 for the input voltage threshold.
2 IN6 Monitored Input Voltage 6. See Table 1 for the input voltage threshold.
3 IN7 Monitored Input Voltage 7. See Table 1 for the input voltage threshold.
4 IN8 Monitored Input Voltage 8. See Table 1 for the input voltage threshold.
5 WDI
Watchdog Timer Input. If WDI remains low or high for longer than the watchdog timeout period, RESET is
asserted and the timer is cleared. The timer also clears whenever a reset is asserted or a rising or falling edge on
WDI is detected. The watchdog timer enters a startup period that allows 54s for the first transition to occur before
a reset. Leave WDI unconnected to disable the watchdog timer. The WDI unconnected state detector uses a
small 400nA current. Therefore, do not connect WDI to anything that will source or sink more than 200nA. Note
that the leakage current specification for most three-state drivers exceeds 200nA.
6 GND Ground
7V
CC Unmonitored Power-Supply Input
8 OUT5 Output 5. When the voltage at IN5 falls below its threshold, OUT5 goes low and stays low until the voltage at IN5
exceeds its threshold. The open-drain output has a 30µA internal pullup to VCC.
9 OUT6 Output 6. When the voltage at IN6 falls below its threshold, OUT6 goes low and stays low until the voltage at IN6
exceeds its threshold. The open-drain output has a 30µA internal pullup to VCC.
10 OUT7 Output 7. When the voltage at IN7 falls below its threshold, OUT7 goes low and stays low until the voltage at IN7
exceeds its threshold. The open-drain output has a 30µA internal pullup to VCC.
11 OUT8 Output 8. When the voltage at IN8 falls below its threshold, OUT8 goes low and stays low until the voltage at IN8
exceeds its threshold. The open-drain output has a 30µA internal pullup to VCC.
12 MR Active-Low Manual Reset Input. Pull MR low to assert RESET low. RESET remains low for the reset timeout period
after MR is deasserted. MR is pulled up to VCC through a 20kΩ resistor.
13 SRT
Set Reset Timeout Input. Connect a capacitor from SRT to GND to set the reset timeout period. The reset timeout
period can be calculated as follows:
Reset Ti m eout ( s) = 2.06 x 106
( Ω) x C
S RT
( F) . For the i nter nal ti m eout p er i od of 140m s ( m i n) , connect S RT to V
C C
.
14 MARGIN Margin Disable Input. Pull MARGIN low to deassert all outputs (go into high state), regardless of the voltage at
any monitored input.
15 OUT4 Output 4. When the voltage at IN4 falls below its threshold, OUT4 goes low and stays low until the voltage at IN4
exceeds its threshold. The open-drain output has a 30µA internal pullup to VCC.
16 OUT3 Output 3. When the voltage at IN3 falls below its threshold, OUT3 goes low and stays low until the voltage at IN3
exceeds its threshold. The open-drain output has a 30µA internal pullup to VCC.
17 OUT2 Output 2. When the voltage at IN2 falls below its threshold, OUT2 goes low and stays low until the voltage at IN2
exceeds its threshold. The open-drain output has a 30µA internal pullup to VCC.
18 OUT1 Output 1. When the voltage at IN1 falls below its threshold, OUT1 goes low and stays low until the voltage at IN1
exceeds its threshold. The open-drain output has a 30µA internal pullup to VCC.
19 RESET
Active-Low Reset Output. RESET asserts low when any of the monitored voltages falls below its respective
threshold or MR is asserted. RESET remains asserted for the reset timeout period after all monitored voltages
exceed their respective thresholds and MR is deasserted. This open-drain output has a 30µA internal pullup.
20 IN1 Monitored Input Voltage 1. See Table 1 for the input voltage threshold.
21 IN2 Monitored Input Voltage 2. See Table 1 for the input voltage threshold.
22 IN3 Monitored Input Voltage 3. See Table 1 for the input voltage threshold.
23 IN4 Monitored Input Voltage 4. See Table 1 for the input voltage threshold.
24 TOL Threshold Tolerance Input. Connect TOL to GND to select 5% threshold tolerance. Connect TOL to VCC to select
10% threshold tolerance.
—EP
E xp osed P ad . E P i s i nter nal l y connected to GN D . C onnect E P to the g r ound p l ane to p r ovi d e a l ow ther m al r esi stance
p ath fr om the IC j uncti on to the P C B. D o not use as the el ectr i cal connecti on to GN D .
Pin Description (MAX16062)
MAX16060/MAX16061/MAX16062
1% Accurate, Quad-/Hex-/Octal-Voltage
µP Supervisors
10 ____________________________________________________________________________________________________________________________________________________________________________
Table 1. Input-Voltage-Threshold Selector
PART IN1 IN2 IN3 IN4 IN5 IN6 IN7 IN8
MAX16060A 3.3 2.5 ADJ 1.8
MAX16060B 3.3 ADJ ADJ 1.8
MAX16060C ADJ 2.5 ADJ 1.8
MAX16060D 3.3 2.5 ADJ ADJ
MAX16060E ADJ ADJ ADJ ADJ
MAX16061A 3.3 2.5 ADJ 1.8 ADJ ADJ
MAX16061B 3.3 ADJ ADJ 1.8 ADJ ADJ
MAX16061C 3.3 2.5 ADJ ADJ ADJ ADJ
MAX16061D ADJ 2.5 ADJ 1.8 ADJ ADJ
MAX16061E ADJ ADJ ADJ ADJ ADJ ADJ
MAX16062A 3.3 2.5 ADJ 1.8 ADJ ADJ ADJ ADJ
MAX16062B 3.3 ADJ ADJ 1.8 ADJ ADJ ADJ ADJ
MAX16062C 3.3 2.5 ADJ ADJ ADJ ADJ ADJ ADJ
MAX16062D ADJ 2.5 ADJ 1.8 ADJ ADJ ADJ ADJ
MAX16062E ADJ ADJ ADJ ADJ ADJ ADJ ADJ ADJ
Note: Other fixed thresholds may be available. Contact factory for availability.
MAX16060/MAX16061/MAX16062
MAX16060D
REFERENCE UNDERVOLTAGE LOCKOUT
VCC
IN1
OUT1
RESET
OUT2
OUT3
OUT4
MARGIN
IN2
IN3
IN4
TOL
VCC
RESET CIRCUIT
WATCHDOG
TIMER CIRCUIT
OUTPUT
DRIVER
EN
MR SRTWDI
TIMING
VCC
VCC
VCC
Figure 1. MAX16060D Functional Diagram
Functional Diagrams
1% Accurate, Quad-/Hex-/Octal-Voltage
µP Supervisors
____________________________________________________________________________________________________________________________________________________________________________11
MAX16060/MAX16061/MAX16062
1% Accurate, Quad-/Hex-/Octal-Voltage
µP Supervisors
12 ____________________________________________________________________________________________________________________________________________________________________________
MAX16061C
REFERENCE UNDERVOLTAGE LOCKOUT
VCC
IN1
OUT1
RESET
OUT2
OUT3
OUT6
MARGIN
IN2
IN3
IN4
TOL
VCC
RESET CIRCUIT
WATCHDOG
TIMER CIRCUIT
OUTPUT
DRIVER
EN
MR SRTWDI
TIMING
VCC
VCC
VCC
IN5
IN6
OUT4
OUT5
Figure 2. MAX16061C Functional Diagram
Functional Diagrams (continued)
MAX16060/MAX16061/MAX16062
MAX16062C
REFERENCE UNDERVOLTAGE LOCKOUT
VCC
IN1
MARGIN
IN2
IN3
IN4
TOL
VCC
RESET CIRCUIT
WATCHDOG
TIMER CIRCUIT
OUTPUT
DRIVER
EN
MR SRTWDI
TIMING
VCC
VCC
IN5
IN6
IN7
IN8
OUT1
RESET
OUT2
OUT3
OUT8
VCC
OUT4
OUT5
OUT6
OUT7
Figure 3. MAX16062C Functional Diagram
Functional Diagrams (continued)
1% Accurate, Quad-/Hex-/Octal-Voltage
µP Supervisors
____________________________________________________________________________________________________________________________________________________________________________13
MAX16060/MAX16061/MAX16062
1% Accurate, Quad-/Hex-/Octal-Voltage
µP Supervisors
14 ____________________________________________________________________________________________________________________________________________________________________________
Detailed Description
The MAX16060/MAX16061/MAX16062 are 1% accurate
low-voltage, quad-/hex-/octal-voltage µP supervisors in
a small thin QFN package. These devices provide
supervisory functions for complex multivoltage systems.
The MAX16060 monitors four voltages; the MAX16061
monitors six voltages; and the MAX16062 monitors eight
voltages.
These supervisors offer independent outputs for each
monitored voltage along with a reset output that asserts
whenever any of the monitored voltages fall below their
respective thresholds or the manual reset input is
asserted. The reset output remains asserted for the
reset timeout after all voltages are above their respec-
tive thresholds and the manual reset input is deassert-
ed. The minimum reset timeout is internally set to
140ms or can be adjusted with an external capacitor.
All open-drain outputs have internal 30µA pullups that
eliminate the need for external pullup resistors.
However, each output can be driven with an external
voltage up to 5.5V. Other features offered include a
manual reset input, a tolerance pin for selecting 5% or
10% input thresholds, and a margin enable function for
deasserting the outputs during margin testing.
An additional feature is a watchdog timer that asserts
RESET when the watchdog timeout period (1.6s typ) is
exceeded. The watchdog timer can be disabled by
leaving WDI unconnected.
Applications Information
Undervoltage-Detection Circuit
The open-drain outputs of the MAX16060/
MAX16061/MAX16062 can be configured to detect an
undervoltage condition. Figure 4 shows a configuration
where an LED turns on when the comparator output is
low, indicating an undervoltage condition. These
devices can also be used in applications such as sys-
tem supervisory monitoring, multivoltage level detection,
and VCC bar-graph monitoring (Figure 5).
Tolerance (TOL)
The MAX16060/MAX16061/MAX16062 feature a pin-
selectable threshold tolerance. Connect TOL to GND to
select 5% threshold tolerance. Connect TOL to VCC to
select 10% threshold tolerance.
Window Detection
A window detector circuit uses two inputs in the config-
uration shown in Figure 6. External resistors set the two
threshold voltages of the window detector circuit.
External logic gates create the OUT signal. The window
detection width is the difference between the threshold
voltages (Figure 7).
MAX16060
GND
VCC
IN1V1
5V
V2
V3
V4 OUT1
IN2
IN3
IN4
OUT2
OUT3
OUT4
Figure 4. Quad Undervoltage Detector with LED Indicators
MAX16060
GND
D2
VCC
IN1
VIN (5V)
5V
OUT1
IN2
IN3
IN4
OUT2
OUT3
OUT4
D1
D3
D4
Figure 5. VCC Bar-Graph Monitoring
MAX16060/MAX16061/MAX16062
1% Accurate, Quad-/Hex-/Octal-Voltage
µP Supervisors
____________________________________________________________________________________________________________________________________________________________________________15
Adjustable Input
These devices offer several monitor options with
adjustable input thresholds (see Table 1). The threshold
voltage at each adjustable IN_ input is typically 0.394V
(TOL = GND) or 0.373V (TOL = VCC). To monitor a volt-
age VINTH, connect a resistive-divider network to the cir-
cuit as shown in Figure 8.
VINTH = VTH ((R1/R2) + 1)
R1 = R2 ((VINTH/VTH) - 1)
Large resistors can be used to minimize current through
the external resistors. For greater accuracy, use lower-
value resistors.
Unused Inputs
Connect any unused IN_ inputs to a voltage above its
threshold.
OUT_
Outputs
The OUT_ outputs go low when their respective IN_
inputs drop below their specified thresholds. The output
is open drain with a 30µA internal pullup to VCC. For
many applications, no external pullup resistor is required
to interface with other logic devices. An external pullup
resistor to any voltage from 0 to 5.5V overrides the inter-
nal pullup if interfacing to different logic supply voltages.
Internal circuitry prevents reverse current flow from the
external pullup voltage to VCC (Figure 9).
MAX16060E
GND
VCC
IN1
5V
R2
INPUT
R1
OUT1
IN2
IN3
OUT
IN4
OUT2
OUT3
OUT4
R4
R3
VTH1 = (1 + R1) (VTH + VTH_HYS)
R2
VTH4 = (1 + R3) VTH
R4
Figure 6. Window Detection
R1
VINTH
VTH
R2
R1 = R2(VINTH )
VTH
- 1
Figure 8. Setting the Adjustable Input
ΔV TH
V TH4
V TH1
OUT
OUT4
OUT1
Figure 7. Output Response of Window Detector Circuit
MAX16060/MAX16061/MAX16062
1% Accurate, Quad-/Hex-/Octal-Voltage
µP Supervisors
16 ____________________________________________________________________________________________________________________________________________________________________________
RESET
Output
RESET asserts low when any of the monitored voltages
fall below their respective thresholds or MR is asserted.
RESET remains asserted for the reset timeout period
after all monitored voltages exceed their respective
thresholds and MR is deasserted (see Figure 10). This
open-drain output has a 30µA internal pullup. An external
pullup resistor to any voltage from 0 to 5.5V overrides the
internal pullup if interfacing to different logic supply volt-
ages. Internal circuitry prevents reverse current flow from
the external pullup voltage to VCC (Figure 9).
Reset Timeout Capacitor
The reset timeout period can be adjusted to accommo-
date a variety of µP applications. Adjust the reset time-
out period (tRP) by connecting a capacitor (CSRT)
between SRT and GND. Calculate the reset timeout
capacitor as follows:
Connect SRT to VCC for a factory-programmed reset
timeout of 140ms (min).
Manual Reset Input (
MR
)
Many µP-based products require manual reset capabil-
ity, allowing the operator, a test technician, or external
logic circuitry to initiate a reset. A logic-low on MR
asserts RESET low. RESET remains asserted while MR
is low, and during the reset timeout period (140ms min)
after MR returns high. The MR input has an internal
20kΩpullup resistor to VCC, so it can be left uncon-
nected if not used. MR can be driven with TTL or
CMOS-logic levels, or with open-drain/collector outputs.
Connect a normally open momentary switch from MR to
GND to create a manual reset function. External
debounce circuitry is not required. If MR is driven from
long cables or if the device is used in a noisy environ-
ment, connecting a 0.1µF capacitor from MR to GND
provides additional noise immunity.
CFtsxI
V
SRT RP SRT
TH SRT
() ()
_
=
MAX16060
MAX16061
MAX16062
GND
VCC
GND
RESET
VCC
5V
OUT_
VCC = 3.3V
100kΩ
Figure 9. Interfacing to a Different Logic Supply Voltage
IN_
10%
90%
10%
90%
RESET
OUT_
VTH_
tRP
tD
tD
tRD
VTH_
Figure 10. Output Timing Diagram
MAX16060/MAX16061/MAX16062
1% Accurate, Quad-/Hex-/Octal-Voltage
µP Supervisors
____________________________________________________________________________________________________________________________________________________________________________17
Margin Output Disable (
MARGIN
)
MARGIN allows system-level testing while power sup-
plies are adjusted from their nominal voltages. Drive
MARGIN low to force RESET and OUT_ high, regard-
less of the voltage at any monitored input. The state of
each output does not change while MARGIN = GND.
The watchdog timer continues to run when
MARGIN is low, and if a timeout occurs, RESET will
assert tMD after MARGIN is deasserted.
The MARGIN input is internally pulled up to VCC. Leave
MARGIN unconnected or connect to VCC if unused.
Undervoltage Lockout (UVLO)
The MAX16060/MAX16061/MAX16062 feature a VCC
undervoltage lockout (UVLO) that preserves a reset
status even if VCC falls as low as 1V. The undervoltage
lockout circuitry monitors the voltage at VCC. If VCC
falls below the UVLO falling threshold (typically
1.735V), RESET is asserted and all OUT_ are asserted
low. This eliminates an incorrect RESET or OUT_ output
state as VCC drops below the normal VCC operational
voltage range of 1.98V to 5.5V.
During power-up as VCC rises above 1V, RESET is
asserted and all OUT_ are asserted low until VCC
exceeds the UVLO threshold. As VCC exceeds the UVLO
threshold, all inputs are monitored and the correct output
state appears at all the outputs. This also ensures that
RESET and all OUT_ are in the correct state once VCC
reaches the normal VCC operational range.
Power-Supply Bypassing
In noisy applications, bypass VCC to ground with a
0.1µF capacitor as close to the device as possible. The
additional capacitor improves transient immunity. For
fast-rising VCC transients, additional capacitance may
be required.
MAX16060/MAX16061/MAX16062
1% Accurate, Quad-/Hex-/Octal-Voltage
µP Supervisors
Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are
implied. Maxim reserves the right to change the circuitry and specifications without notice at any time.
18
____________________Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600
© 2008 Maxim Integrated Products is a registered trademark of Maxim Integrated Products, Inc.
Pin Configurations
+
15
16
14
13
6
5
7
IN4
GND
8
IN3
OUT2
SRT
OUT1
12
IN1
4
12 11 9
IN2
TOL
MR
OUT4
OUT3
VCC
MAX16060
WDI MARGIN
3
10
RESET
THIN QFN
(4mm x 4mm)
TOP VIEW
+
19
20
18
17
7
6
8
IN5
WDI
GND
9
IN4
OUT2
MARGIN
SRT
OUT1
12
IN2
45
15 14 12 11
IN3
TOL
OUT6
OUT5
OUT4
VCC
MAX16061
IN6 OUT3
3
13
IN1
16 10 MR
RESET
THIN QFN
(4mm x 4mm)
TOP VIEW
+
MARGIN
SRT
23
24
22
21
8
7
9
IN6
IN8
WDI
GND
10
IN5
12
IN3
456
1718 16 14 13
IN4
TOL
OUT7
OUT6
OUT5
VCC
MAX16062
IN7
3
15
IN2
20 11 OUT8
IN1
19 12 MR
RESET
THIN QFN
(4mm x 4mm)
TOP VIEW
OUT2
OUT1
OUT3
OUT4
Chip Information
PROCESS: BiCMOS
Package Information
For the latest package outline information, go to
www.maxim-ic.com/packages.
PACKAGE TYPE PACKAGE CODE DOCUMENT NO.
16 TQFN T1644-4 21-0139
20 TQFN T2044-3 21-0139
24 TQFN T2444-4 21-0139