1 / 4
Den aktuellen Stand des Datenblattes finden Sie auf unserer Internetseite-You can always find the current valid issue of data sheet on our homepage Ausgabe / Issue SMP-2005-11-14
e-mail: vk.bauelemente@isabellenhuette.de - Internet: www.isabellenhuette.de www.isa-asic.de
SMP
Bauform / Size : 2010
ISA-PLAN® - SMD Präzisionswiderstände / SMD precision resistors
MERKMALE / FEATURES
1 Watt Dauerleistung bei 130 °C
1 Watt permanent power at 130 °C
Dauerströme bis 14 A ( 5 mOhm )
Constant current up to 14 Amps ( 5 mOhm )
Sehr kleine Bauform (2010)
Extremly small size (2010)
Sehr hohe Pulsbelastbarkeit
High pulse power rating
Bauteilemontage: Reflow- und IR-Löten
Mounting: reflow- and infrared soldering
APPLIKATIONEN / APPLICATION
Messwiderstand für Leistungshybride
Current sensor for power hybrid applications
Steuergeräte in der Automobiltechnik
Control systems for the automotive market
Leistungsmodule
Power modules
Frequenzumrichter
Frequency converters
Schaltnetzteile
Switch mode power supplies
TECHNISCHE DATEN / TECHNICAL DATA
Widerstandswerte Resistance values 5 mOhm - 1 Ohm
Toleranz Tolerance 0.5 %, 1 %, 2%, 5 %
Temperaturkoeffizient(MANGANIN®) Temperature coefficient (tcr) < 50 ppm/K ( 20 °C to 60 °C )
Temperaturbereich Applicable temperature range -55 °C to +170 °C
Belastbarkeit Load capacity 1 W
Innerer Wärmewiderstand (Rthi) Internal heat resistance (Rthi) < 40 K/W
Isolationsspannung Dielectric withstanding voltage 200 V
Induktivität Inductance < 3 nH
Stabilität (Nennlast) Abweichung TK= Kontaktstellentemperatur
Stability (nominal load) deviation TK= Terminal temperature
< 0.5 % nach/after 2000 h (TK = 95 °C)
< 1.0 % nach/after 2000 h (TK = 130 °C)
Bauform/Size 2010
2 / 4
Den aktuellen Stand des Datenblattes fi nden Sie auf unserer Internetseite-You can always fi nd the current valid issue of data sheet on our homepage Ausgabe / Issue SMP-2005-11-14
e-mail: vk.bauelemente@isabellenhuette.de - Internet: www.isabellenhuette.de www.isa-asic.de
SMP
Bauform / Size : 2010
Temperaturabhängigkeit des elektrischen Widerstandes von
MANGANIN®-Widerständen
Temperature dependence of the electrical resistance of
MANGANIN®-resistors
Lastminderungskurve
Power derating curve
TK, Lastminderung und Langzeitstabilität / TCR, power derating and long term stability
Stabilität/Stability < 1.0 %
Verbesserte Stabilität/Improved stablilty < 0.5 %
Typische Temperaturabhängigkeit eines SMP Widerstandes
Typical temperature dependence of a SMP resistor
Grenzkurve
Limiting curve
Grenzkurve
Limiting curve
Langzeitstabilität von MANGANIN®-Widerständen bei 140 °C
Long term stability of MANGANIN®-resistors at 140 °C
3 / 4
Den aktuellen Stand des Datenblattes fi nden Sie auf unserer Internetseite-You can always fi nd the current valid issue of data sheet on our homepage Ausgabe / Issue SMP-2005-11-14
e-mail: vk.bauelemente@isabellenhuette.de - Internet: www.isabellenhuette.de www.isa-asic.de
SMP
Bauform / Size : 2010
GURTINFORMATIONEN
TAPE & REEL INFORMATION
Norm / Specifi cation DIN EN 60286-3
Gurtbreite / Tape width 12 mm
Anzahl Bauteile/Parts per reel 10000
BESTELLBEZEICHNUNG / ORDERING CODE
SMP-R005-1.0
Typ Widerstandswert Toleranz
Type Resistance value Tolerance
SMP 5 mOhm 1.0 %
Lötprofi l Vorschlag / Recommended solder profi le
Refl ow-, IR-löten
Refl ow, infrared soldering
Temperatur 260 °C 255 °C 217 °C
Zeit (s) peak 40 90
RoHS 2002/95/EG konform seit Produktstart.
Ausführliche Informationen erhalten Sie auf unserer Homepage:
www.isabellenhuette.de
RoHS 2002/95/EC compliance since product launch.
For more information please visit our website:
www.isabellenhuette.de
Vorschlag für Leiterplatten Layout (Refl owlöten)
Proposal for pcb-layout (refl ow soldering)
Gewährleistung
Alle Angaben über Eignung, Verarbeitung und Anwendung unserer Produkte, technische Beratung und sonstige Angaben erfolgen nach bestem
Wissen, befreien den Käufer jedoch nicht von eigenen Prüfungen und Versuchen.
Warranty
All information regarding the suitable, workability and applicability of our products, all technical advice and other information are provided to the
best of our knowledge and belief, but shall not discharge the buyer from his own examinations and tests.
4 / 4
Den aktuellen Stand des Datenblattes fi nden Sie auf unserer Internetseite-You can always fi nd the current valid issue of data sheet on our homepage Ausgabe / Issue SMP-2005-11-14
e-mail: vk.bauelemente@isabellenhuette.de - Internet: www.isabellenhuette.de www.isa-asic.de
SMP
Bauform / Size : 2010
10000 1000
MIL. - STANDARD
Parameters Test Conditions Specifi cation
Maximum Temperature for full power operation 130 °C 130 °C
Working Temperature -55 to 170 °C -55 to 170 °C
Thermal Shock MIL-STD-202 method 107E-B1 0.1 %
Overload MIL-R-26E (5 times rated power, 5 sec) 0.2 %
Solderability MIL-STD-202 method 208 > 95 % coverage
Resistance to Solvents MIL-STD-202 method 215A, 2.1a, 2.1d no damage
Low Temperature Storage and Operation MIL-STD-26E 0.1 %
Resistance to Soldering Heat MIL-STD-202 method 210B 0.1 %
Moisture Resistance MIL-STD-202 method 106 0.1 %
Shock MIL-STD-202 method 213B-A 0.2 %
Vibration, High Frequency MIL-STD-202 method 204D-B 0.2 %
Life MIL-STD-26E 0.2 %
Storage Life at Elevated Temperature MIL-STD-202 method 108A-F 0.3 %
High Temperature Exposure 140 °C, 2000 h 0.2%
Current Noise MIL-STD-202 method 308 0.01 %
Voltage Coeffi cient (%/V) MIL-STD-202 method 309 linearity error less than 120dB
Resistance Temperature Characteristic MIL-STD-202 method 304 (20-60°C) <50 ppm/K
Thermal EMF 0 - 100 °C 2 µV/ °C max.
Frequency Characteristic inductivity < 3 nH
Grenzkurve für maximale Pulsenergie bzw. Pulsleistung für Dauerbetrieb
Maximum puls energy resp. pulse power for continous operation
Isabellenhütte Heusler GmbH & Co KG
Eibacher Weg 3-5 - D-35683 Dillenburg - Telefon / Phone +49 (0) 27 71 9 34 - 0 - Fax: +49 (0) 27 71 2 30 30
Die dargestellte Kurve gilt für den Widerstandswert R005. Für andere Werte kann die Kurve im unteren Bereich ggf. anders verlaufen, so dass in Grenzbereichen eine separate
Qualifikation erfolgen sollte.
This curve is only valid for the resistance value R005. The shape of the curve in the range below 0.1 sec will be different for other resistance values. Therefore a separate
qualification should be made for pulse power close to the above curve.