1SD210F2 Data Sheet 1SD210F2-5SNA0400J650100 Single-Channel SCALE Plug-and-Play IGBT Driver Ultra compact, high-performance driver for 2-level, 3-level and multilevel converters Abstract The SCALE plug-and-play driver 1SD210F2-5SNA0400J650100 is a compact single-channel intelligent gate driver designed for ABB's high-voltage IGBTs of type 5SNA0400J650100. The driver features a fiber-optic interface and a selectable operation mode via a jumper. For drivers adapted to other types of high-power and high-voltage IGBT modules, refer to www.IGBT-Driver.com/go/plug-and-play Product Highlights Plug-and-play solution Protects the IGBT from short-circuit failure Active clamping of V ce at turn-off Extremely reliable; long service life No electrolytic capacitors Gate current up to -6A/+10A Fiber-optic links Monitoring of supply voltage and fiber optics Switching frequency DC to max. 6kHz Duty cycle 0... 100% Suitable DC/DC power supply as separate unit Shortens application development time IGBT-Driver.com Applications Three/multi-level converters Two-level converters Medium-voltage converters High-voltage applications Industrial drives Traction Railroad power supplies Wind-power converters Radiology and laser technology Research Almost all other conceivable applications Page 1 1SD210F2 Data Sheet 1SD210F2-5SNA0400J650100 Important Notes This data sheet contains only product-specific data. For a detailed description, mustread application notes and common data that apply to the whole series, please refer to the "Description and Application Manual for 1SD210F2 SCALE High-Voltage IGBT Drivers". When applying SCALE plug-and-play drivers, please note that these drivers are specifically adapted to a particular type of IGBT module. Therefore, the type designation of SCALE plug-and-play drivers also includes the type designation of the corresponding IGBT module. These drivers are not valid for IGBT modules other than those specified. Incorrect use may result in failure. Mechanical and Electrical Interfaces Dimensions: 156 x 79.5 mm. Mounting Principle: Direct screw mount on IGBT. Interface Remarks Part type # Drive signal input (Standard) Drive signal input (Opt. 01) Drive signal input (Opt. 02) Status output (Standard) Status output (Opt. 01) Status output (Opt. 02) Power supply connector Fiber-optic receiver (Notes 14,16) Fiber-optic receiver (Notes 14,16) Fiber-optic receiver (Notes 14,20) Fiber-optic transmitter (Notes 14,17) Fiber-optic transmitter (Notes 14,17) Fiber-optic transmitter (Notes 14,21) On-board connector (Note 15) HFBR-2522 HFBR-2522 HFBR-2412T HFBR-1522 HFBR-1522 HFBR-1412T 77315-101-05 Power supply connector Designator Pin numbers Ground Supply voltage GND (Note 19) 1, 2, 4, 5 3 Page 2 V DC CT-Concept.com 1SD210F2 Data Sheet 1SD210F2-5SNA0400J650100 Absolute Maximum Ratings Parameter Remarks Supply voltage V DC Gate peak current I out Average supply current I DC VDC to GND (Note 1) Output power gate driver Switching frequency DC-link voltage Operating temperature Storage temperature Notes 3,11 Note 11 Note 5 Note 11 Min Max Units 0 17.3 -6 +10 190 225 2 6 4400 -40 +85 -40 +90 V A mA mA W kHz V C C Note 8 Standard and Opt. 1 (Note 3) Opt. 2 (Note 3) Electrical Characteristics All data refer to +25C and V DC = 16.4V unless otherwise specified Power supply Remarks Min Typ. Max Units Nominal supply voltage V DC Supply current I DC VDC to GND (Note 1) Without load (Note 2) Standard and Opt. 1 Opt. 2 15.5 16.4 16.8 V 80 115 14 1.0 mA mA V V Min Typ. Max Units Turn-on threshold V th Hysteresis on/off Note 4 Note 4 Short-circuit protection Remarks V ce -monitoring threshold Response time Response time Blocking time Between aux. terminals 3-level mode (Notes 10,18) 2-level mode (Notes 6,18) 2-level mode (Note 7) Timing characteristics Remarks Turn-on delay t pd(on) Turn-off delay t pd(off) Output rise time t r(out) Output fall time t f(out) Acknowledge delay time Acknowledge pulse width Note Note Note Note IGBT-Driver.com 1200 10.8 11.5 11.6 12.4 1 Min Typ. Max Units 430 520 100 100 450 ns ns ns ns ns s 12 12 9 9 At status output (Note 13) At status output V s s s 0.7 1.8 Page 3 1SD210F2 Data Sheet 1SD210F2-5SNA0400J650100 Gate output Remarks Turn-on gate resistor R g(on) Turn-off gate resistor R g(off) Note 22 Min Typ. Max Units 5.6 22 Footnotes to the key data 1) 2) 3) 4) 5) 6) 7) 8) 9) 10) 11) 12) 13) 14) 15) 16) Supply voltages higher than those specified can lead to the destruction of the driver and protection circuits on the output side. The gate-emitter voltage tracks the supply voltage. (Not regulated by the gate drive unit.) The recommended DC/DC power supply ISO3116I with high-voltage insulation capability is a suitable separate unit. Static power consumption of the gate driver. If the specified power consumption of the gate driver is exceeded on average, this indicates an overload of the gate driver and the external DC/DC power supply ISO3116I. Under-voltage monitoring of supply voltage of the gate driver. For a voltage lower than this limit, the power modules are switched off. This limit is due to active clamping. Refer to the "Description and Application Manual for 1SD210F2 SCALE High-Voltage IGBT Drivers". Pulse width of the direct output of the gate drive unit. (Excluding the delay of the gate resistors.) Duration of blocking the command input (keeping the gate driver and the IGBT in the off-state) after fault detection, i.e. power supply under-voltage lock out, or - only in 2-level mode - shortcircuit detection. (For three/multilevel mode, turn-off under the short-circuit condition is managed by the host controller.) The gate current is limited by on-board gate resistors. Refers to the direct output of the gate drive unit. (Excluding the delay of the gate resistors.) Including the delay of external fiber-optic links. Measured from the turn-on transition at direct output of the gate drive unit (excluding the delay of the gate resistors) to the transition of the status signal at the optical receiver on the host controller side. Application-specific self-heating of gate drivers and IGBT modules, especially at high switching frequency, must be taken into account. The switching frequency is usually limited due to the switching losses of the IGBT modules. Because CONCEPT cannot predict how the drivers will be incorporated in the user's application, no binding recommended value for self-heating and thus for the maximum useable output power can be given. It is therefore recommended to check the gate driver's ambient temperature within the system. Including the delay of external fiber-optic links. Measured from the transition of the turn-on or turn-off command at the optical transmitter on the host controller side to the direct output of the gate drive unit. (Excluding the delay of the gate resistors.) Including the delay of external fiber-optic links. Measured from the transition of the turn-on or turn-off command at the optical transmitter on the host controller side to the transition of the acknowledge signal at the optical receiver on the host controller side. The transceivers required at the host controller side are not supplied with the gate driver. It is recommended to use the same types as used in the gate driver. For product information refer to www.IGBT-Driver.com/go/fiberoptics The connector and cable to the DC/DC power supply are not supplied with the gate driver, but via FCI Inc. Recommended crimp contact housing: order code 65039-032; recommended crimp contacts: 5 pcs, order code 48236-002. Refer to www.IGBT-Driver.com/go/fci The recommended transmitter current at the host controller is 30-35mA, suitable for plastic optic fibers with a length of less than 2.5 meters. A higher current may increase jitter or delay at turnoff. Page 4 CT-Concept.com 1SD210F2 Data Sheet 1SD210F2-5SNA0400J650100 17) 18) 19) 20) 21) 22) The transmitter current at the gate driver is 30-35mA. The delay from the turn-on transition at direct output of the gate drive unit to the turn-on of the IGBT amounts to about 1.5s (due to gate resistors). But turn-off at short circuit takes place without delay; so the real short-circuit time is 1.5s shorter than the response time. GND of the power supply is not at the same electrical potential as the auxiliary emitter terminal of the IGBT. They should never be connected together. The recommended transmitter current at the host controller is 60mA. The transmitter current at the gate driver is about 65mA. This value is the minimum recommended turn-on gate resistance with a DC-link stray inductance of L =280nH. The turn-on gate resistance can be reduced with a lower DC-link stray inductance. Important Notice The data contained in this product data sheet is intended exclusively for technically trained staff. Handling all high-voltage equipment involves risk to life. Strict compliance with the respective safety regulations is mandatory! Any handling of electronic devices is subject to the general specifications for protecting electrostatic-sensitive devices according to international standard IEC 747-1, Chapter IX or European standard EN 100015 (i.e. the workplace, tools, etc. must comply with these standards). Otherwise, this product may be damaged. Disclaimer This data sheet specifies devices but cannot promise to deliver any specific characteristics. No warranty or guarantee is given - either expressly or implicitly - regarding delivery, performance or suitability. CT-Concept Technology AG reserves the right to make modifications to its technical data and product specifications at any time without prior notice. The general terms and conditions of delivery of CT-Concept Technology AG apply. IGBT-Driver.com Page 5 1SD210F2 Data Sheet 1SD210F2-5SNA0400J650100 Ordering Information The general terms and conditions of delivery of CT-Concept Technologie AG apply. Related IGBT CONCEPT Driver Type # ABB 5SNA0400J650100 ABB 5SNA0400J650100 ABB 5SNA0400J650100 1SD210F2-5SNA0400J650100 1SD210F2-5SNA0400J650100 Opt. 01 1SD210F2-5SNA0400J650100 Opt. 02 Opt. 01: Lateral fiber-optic interface (HFBR-2522 and HFBR-1522), see "Description and Application Manual for 1SD210F2 SCALE High-Voltage IGBT Drivers". Opt. 02: Lateral fiber-optic interface with threaded port (HFBR-2412T and HFBR-1412T), see "Description and Application Manual for 1SD210F2 SCALE High-Voltage IGBT Drivers". Information about Other Products For drivers adapted to other high-voltage IGBT modules Direct link: www.IGBT-Driver.com/go/plug-and-play For other drivers and evaluation systems Please click: www.IGBT-Driver.com Manufacturer CT-Concept Technologie AG Intelligent Power Electronics Renferstrasse 15 CH-2504 Biel-Bienne Switzerland Tel. Fax +41 - 32 - 344 47 47 +41 - 32 - 344 47 40 E-mail Internet Info@IGBT-Driver.com www.IGBT-Driver.com (c) Copyright 1999...2007 by CT-Concept Technologie AG - Switzerland. We reserve the right to make any technical modifications without prior notice. Page 6 All rights reserved. Version from 2016-05-20 CT-Concept.com Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Power Integrations: 1SD210F2-5SNA0400J650100 1SD210F2-5SNA0400J650100_Opt1