FieldIT Data Sheet SS/264XC_2 2600T Series Pressure Transmitters Model 264DC Differential/Gauge Model 264HC Gauge Model 264NC Absolute with flanged direct mount seal Base accuracy : 0.075% Span limits - 0.54 to 16000kPa; 2.14inH2O to 2320psi - 1.1 to 16000kPa abs; 8mmHg to 2320psia Reliable sensing system coupled with very latest digital technologies Comprehensive sensor choice - optimize in-use total performance and stability 5-year stability Flexible configuration facilities - provided locally via local keys combined with LCD indicator or via hand held terminal or PC configuration platform Multiple protocol availability - provides integration with HART(R), PROFIBUS PA and FOUNDATION Fieldbus platforms offering interchangeability and transmitter upgrade capabilities Broad selection of variants, options, fill fluids and wetted materials - allows total flexibility maximizing cost-effective aspect, also providing applications with critical process media at extended temperature range PED compliance to sound engineering practice (SEP) ABB 2600T Series Engineered solutions for all applications 2600T Pressure Transmitters Model 264DC, 264HC, 264NC SS/264XC_2 General Description Model 264DC and 264HC/NC detailed in this data sheet apply for those transmitters which include on high pressure measuring side, a direct mount seal which is integral to the transducer by a short capillary connection inside a protective rigid tube. This construction forms a standalone single assembly suitable to be mounted to the process by the seal mounting facilities. By properly selecting the high and low pressure side variant in the ordering codes model 264DC can be in the following versions : a) one direct mount seal and one flange for process connection, 1/4in NPT direct or 1/2in NPT through adapter; this allows also to connect the other leg (wet or dry) for differential measurement. A proper filter is supplied as standard when 1/4in NPT connection is selected, in order to plug the unused entry, leaving it vented for gauge measurement with reference to atmosphere. b) one direct mount seal and one remote seal with capillary; the two seals allow again a differential measurement and must be selected of same type/size. Model 264HC and 264NC have the direct mount seal on the positive side, respectively with the reference at atmospheric or vacuum pressure, for gauge or absolute measurements. Allowed types of direct mount seal are those mainly used for chemical application: - flush diaphragm flange mounted seal - extended diaphragm flange mounted seal These are suitable also for other process applications including food and sanitary, using FDA approved filling, which are defined as food fills and are Generally Recognized As Safe (GRAS) by the US Food and Drug Administration (FDA). Refer to seal data sheet for all data and details relevant to seal element. The following table list the types of standard seal which can be mounted with 264DC/HC/NC transmitters (the mnemonic is used as reference in the compatibility table). Seal type Size Mnemonic Flanged flush diaphragm 2in / DN50 3-4in / DN80-100 P2 P3 Flanged extended diaphragm 2in / DN50 3in / DN80 4in / DN100 E2 E3 P3 All following specification data apply for identical characteristics of the two seals when the transmitter has the remote seal in addition to the direct mount one. Functional Specifications Range and span limits Sensor Code E F G H M P Q S 16kPa 160mbar 64inH2O 40kPa 400mbar 160inH2O 65kPa 650mbar 260inH2O 160kPa 1600mbar 642inH2O 600kPa 6bar 87psi 2400kPa 24bar 348psi 8000kPa 80bar 1160psi Lower Range Limit 264DC 264DC Direct mount Direct mount differential gauge -16kPa -16kPa -160mbar -160mbar -64inH2O -64inH2O -40kPa -40kPa -400mbar -400mbar -160inH2O -160inH2O -65kPa -65kPa -650mbar -650mbar -260inH2O -260inH2O -160kPa 0.07kPa abs () -1600mbar 0.7mbar abs () -642inH2O 0.5mmHg () -600kPa 0.07kPa abs () -6bar 0.7mbar abs () -87psi 0.5mmHg () -2400kPa 0.07kPa abs () -24bar 0.7mbar abs () -348psi 0.5mmHg () -8000kPa 0.07kPa abs () -80bar 0.7mbar abs () -1160psi 0.5mmHg () 16000kPa 160bar 2320psi -16000kPa -160bar -2320psi Upper Range Limit (URL) 0.07kPa abs () 0.7mbar abs () 0.5mmHg () (LRL) 264HC/NC Direct mount gauge/absolute Minimum span 0.07kPa abs () 0.7mbar abs () 0.5mmHg () 0.07kPa abs () 0.7mbar abs () 0.5mmHg () 0.07kPa abs () 0.7mbar abs () 0.5mmHg () 0.07kPa abs () 0.7mbar abs () 0.5mmHg () 0.07kPa abs () 0.7mbar abs () 0.5mmHg () 0.54kPa 5.4mbar 2.14inH2O 0.67kPa 6.7mbar 2.67inH2O 1.1kPa 11mbar 4.35inH2O 2.67kPa 26.7mbar 10.7inH2O 10kPa 0.1bar 1.45psi 40kPa 0.4bar 5.8psi 134kPa 1.34bar 19.4psi 0.07kPa abs () 0.7mbar abs () 0.5mmHg () 267kPa 2.67bar 38.7psi Compatibility (allowed seal for 264DC) Direct mount and Direct mount one remote seal seal only (max length in m.) P2 (*), P3 E3 (*) P3 (3) E3 (2) (*) P2, P3 E2 (*), E3 P2 (2) (*), P3 (5) E3 (3) P2, P3 E2 (*), E3 P2 (2) (*), P3 (5) E3 (3) P2, P3 E2, E3 P2 (5), P3 (8) E2 (4), E3 (6) P2, P3 E2, E3 P2 (8), P3 (8) E2 (6), E3 (8) P2, P3 E2, E3 P2 (8), P3 (8) E2 (6), E3 (8) P2, P3 E2, E3 P2 (8), P3 (8) E2 (6), E3 (8) P2, P3 E2, E3 P2 (8), P3 (8) E2 (6), E3 (8) The combinations sensor code/seal type marked (*) modify the base accuracy rating and static pressure effect; refer to performance specifications. ALL AVAILABLE SEALS FOR DIRECT MOUNT ARE SUITABLE FOR LISTED RANGES OF MODELS 264HC/NC WITHOUT LIMITATION. () Double the value with inert filling 2 2600T Pressure Transmitters Model 264DC, 264HC, 264NC Span limits Maximum span = URL (can be further adjusted up to URL (TD = 0.5) for differential models, within the range limits) IT IS RECOMMENDED TO SELECT THE TRANSMITTER SENSOR CODE PROVIDING THE TURNDOWN VALUE AS LOWEST AS POSSIBLE TO OPTIMIZE PERFORMANCE CHARACTERISTICS. Zero suppression and elevation Zero and span can be adjusted to any value within the range limits detailed in the table as long as: - calibrated span minimum span Damping Selectable time constant : 0, 0.25, 0.5, 1, 2, 4, 8 or 16s. This is in addition to sensor response time Turn on time Operation within specification in less than 1s with minimum damping. SS/264XC_2 Operative limits Temperature limits C (F) : Ambient (is the operating temperature) Model 264DC Filling Sensors Sensor E F to S Silicone oil -40 and +85 -25 and +85 DC 200TM (-40 and +185) (-13 and +185) -20 and +85 -10 and +85 Inert GaldenTM (-4 and +185) (+14 and +185) -20 and +85 -10 and +85 Inert HalocarbonTM (-4 and +185) (+14 and +185) Models 264HC/NC Sensors G to S -40 and +85 (-40 and +185) -20 and +85 (-4 and +185) -20 and +85 (-4 and +185) Lower ambient limit for LCD indicators: -20C (-4F) Upper ambient limit for LCD indicators: +70C (+158F) Note : For Hazardous Atmosphere applications see the temperature range specified on the certificate/approval relevant to the aimed type of protection Insulation resistance > 100M at 1000VDC (terminals to earth) Process Lower limit (low pressure side 264DC only) - refer to lower ambient limits; -20C (-4F) for Viton gasket Upper limit (low pressure side 264DC only) - Silicone oil: 121C (250F) (1) - Inert fluid: 100C (212F) (2) (1) 100C (212F) for application below atmospheric pressure (2) 65C (150F) for application below atmospheric pressure The following table show characteristics of fill fluids when used in transmitters with direct mount seal on high pressure side. OPERATING CONDITIONS FILL FLUIDS (APPLICATION) Tmax Pmin Tmax Tmin @ Pabs>of mbar abs @ P min (psia) Silicone oil-DC200TM 200 (390) 0.7 160 -40 (General purpose) @ 35mbar (0.01) (320) (-40) Silicone oil-AN140TM 250 (480) 0.7 250 -5 (High temperature)) @ 0.7mbar (0.01) (480) (+23) Silicone Polymer-SylthermXLTTM100 (212) 2 20 -100 (Low temperature) @ 110mbar (0.03) (68) (-148) Vegetable oil-Neobee M-20TM 200 (390) 130 150 -18 (Food-Sanitary) FDA @ 1bar (1.9) (300) (0) Glycerin Water (70%) 93 (200) 1000 93 -7 (Food-Sanitary) FDA @ 1bar (14.5) (200) (+20) Mineral oil-MARCOL 82TM 200 (390) 33 40 -40 (Food-Sanitary) FDA @ 200mbar (0.5) (104) (-40) Inert - GaldenTM 160 (320) 0.7 65 -18 (Oxygen Service) @ 1bar (0.01) (150) (0) Inert - HalocarbonTM4.2 180 (356) 4 70 -20 (Oxygen Service) @ 400mbar (0.06) (158) (-4) ABB fill 250 (480) 0.7 160 -10 (Paints and specials) @ 35mbar (0.01) (320) (+14) Storage Lower limit: -50C (-58F); -40C (-40F) for LCD indicators Upper limit: +85C (+185F) 3 2600T Pressure Transmitters Model 264DC, 264HC, 264NC SS/264XC_2 Pressure limits Shock resistance (according to IEC 60068-2-27) Overpressure limits (without damage to the transmitter) 0.067kPa abs, 0.67mbar abs, 0.01psia (double with inert filling) to transmitter sensor limit or flange rating of seal, whichever is less: - 16MPa, 160bar, 2320psi for all sensor codes of model 264DC - 21MPa, 210bar, 3045psi for all sensor codes of models 264HC/NC - 2MPa, 20bar, 290psi for ANSI CL 150 flange 50g Duration: 11ms Wet and dust-laden atmospheres The transmitter is dust and sand tight and protected against immersion effects as defined by EN 60529 (1989) to IP 67 (IP 68 on request) or by NEMA to 4X or by JIS to C0920. Hazardous atmospheres - 5MPa, 50bar, 725psi for ANSI CL 300 flange - 10MPa, 100bar, 1450psi for ANSI CL600 flange - 16MPa, 160bar, 2320psi for ANSI CL 900 flange - 1.6MPa, 16bar, 230psi for DIN PN 16 flange - 4MPa, 40bar, 580psi for DIN PN 40 flange - 6.4MPa, 64bar, 930psi for DIN PN 64 flange - 10MPa, 100bar, 1450psi for DIN PN 100 flange - 16MPa, 160bar, 2320psi for DIN PN 160 flange Static pressure Transmitters for differential pressure model 264DC operates within specifications between the following limits: - 1.3kPa abs,13mbar abs, 0.2psia and 16MPa, 160bar, 2320psi or flange rating of seal as above, whichever is less - 0.067kPa abs, 0.67mbar abs, 0.01psia and 16MPa,160bar, 2320psi or flange rating of seal as above, whichever is less, using a second seal remote on negative pressure side. Proof pressure The transmitter can be exposed without leaking to line pressure of up to: - 28MPa, 280bar, 4000psi for model 264DC - 40MPa, 400bar, 5900psi for model 264HC/NC or two times the flange rating of seal, whichever is less. Meet ANSI/ISA-S 82.03 hydrostatic test requirements and SAMA PMC 27.1. Environmental limits Electromagnetic compatibility (EMC) Comply with EN 61000-6-3 for emission and EN 61000-6-2 for immunity requirements and test; Radiated electromagnetic immunity level: (according to IEC 1000-4-3, EN61000-4-3) 30V/m Conducted electromagnetic immunity level : (according to IEC 1000-4-6, EN 61000-4-6) 30V Surge immunity level (with surge protector): (according to IEC 1000-4-5 EN 61000-4-5) 4kV Fast transient (Burst) immunity level: (according to IEC 1000-4-4 EN 61000-4-4) 4kV Pressure equipment directive (PED) Comply with 97/23/EEC following sound engineering practice (SEP). Humidity Relative humidity: up to 100% annual average Condensing, icing: admissible Vibration resistance Accelerations up to 2g at frequency up to 1000Hz (according to IEC 60068-2-26) 4 Acceleration: With or without output meter/integral display - INTRINSIC SAFETY/EUROPE: ATEX/ZELM approval II 1 GD T50C, EEx ia IIC T6 (-40C Ta +40C) T95C, EEx ia IIC T4 (-40C Ta +85C) - TYPE "N"/EUROPE: ATEX/ZELM type examination (for HART) II 3 GD T50C, EEx nL IIC T6 (-40C Ta +40C) T95C, EEx nL IIC T4 (-40C Ta +85C) (FOUNDATION Fieldbus/PROFIBUS PA): pending - FLAMEPROOF/EUROPE: ATEX/CESI approval II 1/2 GD T85C, EEx d IIC T6 (-40C Ta +75C) - CANADIAN STANDARDS ASSOCIATION and FACTORY MUTUAL: - Explosionproof: Class I, Div. 1, Groups A, B, C, D - Dust ignitionproof : Class II, Div. 1, Groups E, F, G - Suitable for : Class II, Div. 2, Groups F, G; Class III, Div. 1, 2 - Nonincendive: Class I, Div. 2, Groups A, B, C, D - Intrinsically safe: Class I, II, III, Div. 1, Groups A, B, C, D, E, F, G AEx ia IIC T6/T4, Zone 0 (FM) - STANDARDS AUSTRALIA (SAA): pending TS/WCA Approval Ex d IIC T5 (Tamb +85C)/T6 (Tamb +70C) Class 1 Zone 1; Ex ia IIC T4 (Tamb +85C) /T5 (Tamb +55C) T6 Class 1 Zone 0 2600T Pressure Transmitters Model 264DC, 264HC, 264NC SS/264XC_2 Electrical Characteristics and Options Optional surge protection HART digital communication and 4 to 20mA output Power Supply Up to 4kV - voltage 1.2 s rise time / 50 s delay time to half value - current 8 s rise time / 20 s delay time to half value The transmitter operates from 10.5 to 42VDC with no load and is protected against reverse polarity connection (additional load allows operations over 42VDC). For EEx ia and other intrinsically safe approval power supply must not exceed 30VDC. Output signal Two-wire 4 to 20mA, user-selectable for linear or square root output, power of 3/2 or 5/2, 5th order or two 2nd order switching point selectable programmable polynomial output. HART(R) communication provides digital process variable (%, mA or engineering units) superimposed on 4 to 20mA signal, with protocol based on Bell 202 FSK standard. Ripple 20mV max on a 250 load as per HART specifications MINIMUM OPERATING VOLTAGES Output current limits (to NAMUR standard) Overload condition no link on output indicator plugs with CoMeter indicator and HART communication - Lower limit: 3.8mA - Upper limit: 20.5mA with ProMeter output indicator Transmitter failure mode (to NAMUR standard) with optional surge protection The output signal can be user-selected to a value of 3.7 or 22mA on gross transmitter failure condition, detected by self-diagnostics. with optional output analog indicator In case of CPU failure the output is driven <3.7mA or >22mA. with integral display (volts) 10.5 10.7 12.3 12.5 13.3 15.3 Load limitations 4 to 20mA and HART total loop resistance : Supply voltage - min. operating voltage (VDC) --------------------------------------- 22.5 A minimum of 250 is required for HART communication. R(k) = Optional indicators Output meter CoMeter and Prometer LCD : 5-digit (99999 counts) programmable with 7.6mm. high (3in), 7-segment numeric characters plus sign and digital point for digital indication of output value in percentage, current or engineer unit; 10-segment bargraph display (10% per segment) for analog indication of output in percentage; 7-digit with 6mm. high (2.3in), 14-segment alphanumeric characters, for engineer units and configuration display Analog : 36mm (1.4in) scale on 90. Integral display LCD, 15 lines x 56 column dot matrix providing 2 lines indication as - top: 5-digit (numeric) plus sign or 7-digit alphanumeric - bottom: 7-digit alphanumeric and additional 50-segment bargraph for indication of analog output in percentage. User-definable matrix display mode with HART communication: - process variable in pressure unit or - output signal as percentage, current or engineering units Display also indicates in/out transfer function, static pressure, sensor temperature and diagnostic messages and provides configuration facilities. 5 2600T Pressure Transmitters Model 264DC, 264HC, 264NC SS/264XC_2 PROFIBUS PA output FOUNDATION Fieldbus output Device type Device type Pressure transmitter compliant to Profiles 3.0 Class A & B; ident. number 052B HEX. Power supply The transmitter operates from 10.5 to 32VDC , polarity independent. For EEx ia approval power supply must not exceed 17.5VDC. Intrinsic safety installation according to FISCO model. Current consumption operating (quiescent): 10.5mA fault current limiting: 20mA max. Output signal Physical layer in compliance to IEC 1158-2/EN 61158-2 with transmission to Manchester II modulation, at 31.25kbit/sec. Output interface PROFIBUS PA communication according to Profibus DP50170 Part 2/ DIN 19245 part 1-3. Output update time 25ms Function blocks 2 analog input, 1 transducer, 1 physical Integral display LCD, 15 lines x 56 column dot matrix providing 2 lines indication as - top: 5-digit (numeric) plus sign or 7-digit alphanumeric - bottom: 7-digit alphanumeric and additional 50-segment bargraph for indication of output in percentage of the analog input function block assigned to the primary variable. User-definable matrix display mode: - process variable in pressure units or - primary variable in engineering units (output of transducer block) or - output as percentage or engineering units of analog input function blocks Display also indicates diagnostic messages and provides configuration facilities. Secondary variable, static pressure and sensor temperature can be read. Transmitter failure mode On gross transmitter failure condition, detected by self-diagnostics, the output signal can be driven to defined conditions, selectable by the user as safe, last valid or calculated value. If electronic failure or short circuit occur the transmitter consumption is electronically limited at a defined value (20mA approx), for safety of the network. LINK MASTER DEVICE Link Active Scheduler (LAS) capability implemented. Power supply The transmitter operates from 9 to 32VDC, polarity independent. For EEx ia approval power supply must not exceed 24VDC (entity certification) or 17.5VDC (FISCO certification), according to FF-816. Current consumption operating (quiescent): 10.5mA fault current limiting: 20mA max. Output signal Physical layer in compliance to IEC 1158-2/EN 61158-2 with transmission to Manchester II modulation, at 31.25kbit/sec. Function blocks/execution period 2 standard Analog Input blocks/25ms max (each) 1 standard PID block/70ms max. Additional blocks 1 standard Resource block, 1 custom Pressure with calibration transducer block. Number of link objects 25 Number of VCRs 24 Output interface FOUNDATION fieldbus digital communication protocol to standard H1, compliant to specification V. 1.5; FF registration number IT019000. Integral display LCD, 15 lines x 56 column dot matrix providing 2 lines indication as - top: 5-digit (numeric) plus sign or 7-digit alphanumeric - bottom: 7-digit alphanumeric and additional 50-segment bargraph for indication of output in percentage of the analog input function block assigned to the primary variable. User-definable matrix display mode: - process variable in pressure units or - primary variable in engineering units (output of transducer block) or - output as percentage or engineering units of analog input function blocks Display also indicates diagnostic messages and provides configuration facilities. Secondary variable, static pressure and sensor temperature can be read. Transmitter failure mode The output signal is "frozen" to the last valid value on gross transmitter failure condition, detected by self-diagnostics which also indicate a BAD conditions. If electronic failure or short circuit occur the transmitter consumption is electronically limited at a defined value (20mA approx), for safety of the network. 6 2600T Pressure Transmitters Model 264DC, 264HC, 264NC Performance specifications Stated at reference condition to IEC 60770 ambient temperature of 20C (68F), relative humidity of 65%, atmospheric pressure of 1013hPa (1013mbar), mounting position with vertical diaphragm and zero based range for transmitter with isolating diaphragms in AISI 316 L ss or Hastelloy and silicone oil fill and HART digital trim values equal to 4-20mA span end points, in linear mode. Unless otherwise specified, errors are quoted as % of span. Some performance data are affected by the actual turndown (TD) as ratio between Upper Range Limit (URL) and calibrated span. IT IS RECOMMENDED TO SELECT THE TRANSMITTER SENSOR CODE PROVIDING THE TURNDOWN VALUE AS LOWEST AS POSSIBLE TO OPTIMIZE PERFORMANCE CHARACTERISTICS. Accuracy rating % of calibrated span, including combined effects of terminal based linearity, hysteresis and repeatability. For fieldbus versions SPAN refer to analog input function block outscale range Using direct mount seal sizes <DN 80/3in - 0.075% for TD from 1:1 to 10:1 (0.10% for sensor code F 0.10% for sensor code E for TD from 1:1 to 5:1) URL Span - 0.0075% x Operating influences Temperature effects per 20K (36F) ambient temperature change on transmitter sensor between the limits of -20C to +65C (-4 to +150F) : Transmitter effect: - (0.04% URL + 0.065% span) Direct mount seal additional effect: Error Seal type size for TD from 10:1 to 20:1 URL Span for sensor code F 0.02% x URL Span for sensor code E for TD from 5:1 to 10:1) Using direct mount seal sizes DN 80/3in - 0.075% for TD from 1:1 to 10:1 (0.10% for sensor code E for TD from 1:1 to 5:1) URL for TD from 10:1 to 20:1 Span URL for sensor code E for TD from 5:1 to 10:1) Span - 0.0075% x Multiply the values by 1.5 for sensor/seal combination marked (*) and for transmitter with direct mount seal plus one remote seal. inH20 kPa mbar Flush 2in/DN50 0.12 1.2 0.48 Flush 3-4in/DN80-100 0.02 0.2 0.08 Extended 2in/DN50 0.2 2 0.8 Extended 3in/DN80 0.06 0.6 0.24 Extended 4in/DN100 0.02 0.2 0.08 per 20K (36F) process temperature change on seal diaphragm between the process operating temperature limits Error Seal type size Flush 2in/DN50 (0.01% x (0.02% x SS/264XC_2 kPa mbar inH20 0.32 3.2 1.28 0.4 Flush 3-4in/DN80-100 0.1 1 Extended 2in/DN50 0.35 3.5 1.4 Extended 3in/DN80 0.17 1.7 0.68 Extended 4in/DN100 0.1 1 0.4 Optional CoMeter and ProMeter ambient temperature Total reading error per 20K (36F) change between the ambient limits of -20 and +70C (-4 and +158F) : 0.15% of max span (16mA). Static pressure (zero errors can be calibrated out at line pressure) seal effect additional to transmitter sensor effect applicable for differential measurement per 2MPa, 20bar or 290psi. Model 264DC direct mount seal only - zero error: 0.15% of URL - span error: 0.15% of reading Model 264DC direct mount plus remote seal - zero error: 0.20% of URL - span error: 0.20% of reading Multiply by 1.5 the errors for sensor seal combinations marked (*). Supply voltage Within voltage/load specified limits the total effect is less than 0.005% of URL per volt. Load Within load/voltage specified limits the total effect is negligible. Radio frequency interference Total effect : less than 0.10% of span from 20 to 1000MHz and for field strengths up to 30V/m when tested with shielded conduit and grounding, with or without meter. Common mode interference No effect from 100Vrms @ 50Hz, or 50VDC Vibration effect 0.10% of URL (according to IEC 61298-3) 7 2600T Pressure Transmitters Model 264DC, 264HC, 264NC Physical Specification (Refer to ordering information sheets for variant availability related to specific model or versions code) Materials Model 264DC only Low pressure side process isolating diaphragms (*) AISI 316 L ss; Hastelloy C276TM; Monel 400TM; Tantalum; Hastelloy C276TM on AISI 316 L ss gasket seat. A remote seal can be selected with required diaphragm (refer to high pressure side). SS/264XC_2 High pressure side fill fluid (direct mount seal) Silicone oil-DC200TM, Silicone oil-AN 140TM, Inert-GaldenTM, Inert-HalocarbonTM 4.2, Silicone Polymer-Syltherm XLTTM, Vegetable oil-Neobee M-20TM, Glycerin Water, Mineral oil-MARCOL 82TM, ABB fill. Sensor fill fluid Silicone oil (DC200); inert fill (Halocarbon TM 4.2 or GaldenTM); Sensor housing AISI 316 L ss. Electronic housing and covers Barrel version Low pressure side process flanges, adapters, plugs and drain/vent valves (*) AISI 316 L ss; Hastelloy C276TM; Monel 400TM. Bolts and nuts AISI 316 ss bolts and nuts Class A4-50 per UNI 7323 (ISO 3506), in compliance with NACE MR0175 Class II. Gaskets (*) VitonTM; PTFE. Model 264DC/HC/NC High pressure side process diaphragm (direct mount seal) (*) AISI 316 L ss; Hastelloy C276TM , Tantalum; AISI 316 L ss or Hastelloy C276TM with anti-stick coating; AISI 316 L ss with anti-corrosion coating. Extension material AISI 316 L ss; Hastelloy C276TM; AISI 316 L ss or Hastelloy C276TM with coating same as diaphragm. 8 - Copper-free content aluminium alloy with baked epoxy finish; - Low-copper content aluminium alloy with baked epoxy finish; - AISI 316 L ss. DIN version - Low-copper content aluminium alloy with baked epoxy finish. Covers O-ring Buna N. Local zero and span adjustments: Glass filled polycarbonate plastic (removable). Tagging AISI 316ss data plate attached to the electronics housing. 2600T Pressure Transmitters Model 264DC, 264HC, 264NC Calibration SS/264XC_2 Electrical connections Standard: at maximum span, zero based range, ambient temperature and pressure; Two 1/2 NPT or M20x1.5 or PG 13.5 or 1/2 GK threaded conduit entries, direct on housing. Optional: at specified range and ambient conditions. Special communication connector (on request) Optional extras - HART : straight or angle Harting Han connector and one plug. - FOUNDATION Fieldbus, PROFIBUS PA: M12x1 and 7/8. Output indicator plug-in rotatable type, LCD or analog. Supplemental customer tag AISI 316 ss tag screwed/fastened to the transmitter for customer's tag data up to a maximum of 20 characters and spaces on one line for tag number and tag name, and up to a maximum of 3 spaced strings of 10 characters each for calibration details (lower and upper values plus unit). Special typing evaluated on request for charges. Surge protection (only as external unit for PROFIBUS PA and FF) Cleaning procedure for oxygen service Hydrogen or special service preparation Test Certificates (test, design, calibration, material traceability) Terminal block HART version: three terminals for signal/external meter wiring up to 2.5mm2 (14AWG) and three connection points for test and communication purposes. Fieldbus versions: two terminals for signal wiring (bus connection) up to 2.5mm2 (14AWG) Grounding Internal and external 6mm2 (10AWG) ground termination points are provided. Mounting position Transmitter can be mounted in any position. Electronics housing may be rotated to any position. A positive stop prevents over travel. Tag and manual language Communication connectors Process connections on conventional flanges : 1/4in NPT on process axis on adapters : 1/2in NPT on process axis fixing threads: 7/16in-20 UNF at 41.3mm centre distance Mass (without options) 7kg to 30kg approx (15 to 65lb) according to specified seal(s) options; add 1.5kg (3.4lb) for AISI housing. Add 650g (1.5lb) for packing. Packing Carton on mounting flange (seal side) Flush diaphragm flanged seal (**): 2in or 3in ANSI 150 to 900 RF; 4in ANSI 150-300RF. DN50 or DN80 DIN PN16-40 Form C, PN64-160 Form E; DN100 ND 16 - 40 Form C. Extended diaphragm flanged seal (**): 2in, 3in, 4in ANSI 150 - 300 RF. DN50, DN80, DN100 PN16 - 40 Form C. 9 2600T Pressure Transmitters Model 264DC, 264HC, 264NC Configuration Transmitter with HART communication and 4 to 20 mA Standard configuration Transmitters are factory calibrated to customer's specified range. Calibrated range and tag number are stamped on the tag plate. If a calibration range and tag data are not specified, the transmitter will be supplied with the plate left blank and configured as follows: Engineering Unit Specify from table 4 mA Zero 20 mA Upper Range Limit (URL) Output Linear Damping 1 sec. Transmitter failure mode Upscale Software tag characters Blank Optional LCD indicator/display 0 to 100.0% linear Any or all the above configurable parameters, including Lower range-value and Upper range-value which must be the same unit of measure, can be easily changed using the HART hand-held communicator or by a PC running the configuration software SMART VISION with DTM for 2600T. The transmitter database is customized with specified flange type and material, O-ring and drain/vent materials and meter code option. Custom configuration (option) The following data may be specified in addition to the standard configuration parameters: Descriptor 16 alphanumeric characters Message 32 alphanumeric characters Date Day, month, year Transmitter with PROFIBUS PA communication Transmitters are factory calibrated to customer's specified range. Calibrated range and tag number are stamped on the tag plate. If a calibration range and tag data are not specified, the transmitter will be supplied with the plate left blank and configured as follows: Measure Profile Pressure Engineering Unit kPa Output scale 0% Lower Range Limit (LRL) Output scale 100% Upper Range Limit (URL) Output Linear Hi-Hi Limit Upper Range Limit (URL) Hi Limit Upper Range Limit (URL) Low Limit Lower Range Limit (LRL) Low-Low Limit Lower Range Limit (LRL) Limits hysteresis 0.5% of output scale PV filter 0 sec. Address (settable by local key) 126 Tag 32 alphanumeric characters Any or all the above configurable parameters, including Lower range-value and Upper range-value which must be the same unit of measure, can be easily changed by a PC running the configuration software SMART VISION with DTM for 2600T. The transmitter database is customized with specified flange type and material, O-ring and drain/vent materials and meter code option. Custom configuration (option) The following data may be specified in addition to the standard configuration parameters: Descriptor 32 alphanumeric characters Message 32 alphanumeric characters Date Day, month, year 10 SS/264XC_2 Transmitter with FOUNDATION Fieldbus communication Transmitters are factory calibrated to customer's specified range. Calibrated range and tag number are stamped on the tag plate. If a calibration range and tag data are not specified, the transmitter will be supplied with the plate left blank and the analog input function block FB1 is configured as follows: Measure Profile Pressure Engineering Unit kPa Output scale 0% Lower Range Limit (LRL) Output scale 100% Upper Range Limit (URL) Output Linear Hi-Hi Limit Upper Range Limit (URL) Hi Limit : Upper Range Limit (URL) Low Limit Lower Range Limit (LRL) Low-Low Limit Lower Range Limit (LRL) Limits hysteresis 0.5% of output scale PV filter time 0 sec. Tag 32 alphanumeric characters The analog input function block FB2 is configured for the sensor temperature measured in C. Any or all the above configurable parameters, including the range values, can be changed using any host compliant to FOUNDATION fieldbus. The transmitter database is customized with specified flange type and material, O-ring and drain/vent materials and meter code option. For any protocol available engineering units of pressure measure are : Pa, kPa, MPa inH2O@4C, mmH2O@4C, psi inH2O@20C, ftH2O@20C, mmH2O@20C inHg, mmHg, Torr g/cm2, kg/cm2, atm mbar, bar TM Hastelloy is a Cabot Corporation trademark TM Monel is an International Nickel Co. trademark TM Viton is a Dupont de Nemour trademark TM DC200 is a Dow Corning Corporation trademark TM Galden is a Montefluos trademark TM Halocarbon is a Halocarbon Products Co. trademark TM AN140 is a Wacker-Chemie trademark TM Neobee M20 is a Stepan Company trademark TM Marcol is a Esso Italiana trademark TM Syltherm is a Dow Chemical Company trademark (*) Wetted parts of the transmitter. (**) Bolts and nuts, gasket and mating flange supplied by customer. 2600T Pressure Transmitters Model 264DC, 264HC, 264NC SS/264XC_2 MOUNTING DIMENSIONS (not for construction unless certified) - dimensions in mm (in) 264DC with direct mount flanged flush diaphragm seal (barrel housing) Adjustments 26 (1.02) 17 (0.67) Identification tag 127 (5.00) 36 (1.42) 17 (0.67) Min. clearance to remove the cover Certification label L ES C C I R IR C U G A RD ER KE L E T QU AN E' T H E N W ! E RC L E B I E UV ER T N FER V I GH M CO E P CO T E 135 (5.31) N IO Terminal side E A + B Output meter housing Drain/vent Valve Integral display housing S ON T S O I TS AL I V U S T E E CU T S I NS Electronic side Electrical connections 86 (3.39) A Process connection C D F 71 (2.80) G 144 (5.67) NOTE: Low pressure side opposite to direct mount seal can be a conventional flange or suitable for capillary to remote seal. Conventional process flange connection (1/4in NPT direct or 1/2in NPT through adapter), gasket groove and gaskets are in accordance with DIN 19213. Bolting threads or fixing adapter for other devices on process flange is 7/16in-20 UNF. 26 (1.02) 17 (0.67) 127 (5.00) 86 (3.39) 36 (1.42) 17 (0.67) N IO L ES C C I R IR C U S ON T S O U AL I VE S T E NS I TS CU T S I G A RD ER KE L E T QU AN E' T H E N W ! 135 (5.31) E RC L E B I E UV ER T N FER V I GH M CO E P CO T E A + B E A C D F G 144 (5.67) 11 2600T Pressure Transmitters Model 264DC, 264HC, 264NC SS/264XC_2 Output meter housing Integral display housing Harting Han connector 36 (1.42) Electronic side 17 (0.67) 264DC with direct mount flanged extended diaphragm seal (DIN housing) 26 (1.02) G A RD ER KE L E T QU AN E' T H E N W ! 146 (5.75) 50, 100 or 150 (1.97, 3.94 or 5.91) N IO L ES C C I R IR C U NS S ON T S O I TS AL I V U S T E E CU T S I E RC L E B I E UV ER T N FER V I GH M CO E P CO T E 17 (0.67) B A E + A C D 12 G F 144 (5.67) 27 (1.06) 2600T Pressure Transmitters Model 264DC, 264HC, 264NC SS/264XC_2 264HC/NC with direct mount flanged diaphragm seal (barrel housing) 26 (1.02) 17 (0.67) 127 (5.00) 36 (1.42) 17 (0.67) Electrical connections 86 (3.39) 100 (3.94) E L ES C C I R IR C U E T QU AN E' T H E N W G A RD ER KE L N IO NS S ON T S O I TS AL I V U S T E E CU T S I ! 18 (0.71) C (*) G F D 76 (2.99) 16 (0.63) E RC L E B I E UV ER T N FER V I GH M CO E P CO T E A A B (*) Flush, 50, 100 or 150mm (1.97, 3.94 or 5.91in) extension Dimensions mm (in) Size/Rating 2in ANSI CL 150 2in ANSI CL 300 2in ANSI CL 600 2in ANSI CL 900 3in ANSI CL 150 3in ANSI CL 300 3in ANSI CL 600 3in ANSI CL 900 4in ANSI CL 150 4in ANSI CL 300 DN50 DIN PN16 DN50 DIN PN40 DN50 DIN PN64 DN50 DIN PN100 DN50 DIN PN160 DN80 DIN PN16 DN80 DIN PN40 DN80 DIN PN64 DN80 DIN PN100 DN80 DIN PN160 DN100 DIN PN16 DN100 DIN PN40 A (dia) flush 60 (2.36) 60 (2.36) 60 (2.36) 60 (2.36) 89 (3.5) 89 (3.5) 89 (3.5) 89 (3.5) 89 (3.5) 89 (3.5) 60 (2.36) 60 (2.36) 60 (2.36) 60 (2.36) 60 (2.36) 89 (3.5) 89 (3.5) 89 (3.5) 89 (3.5) 89 (3.5) 89 (3.5) 89 (3.5) extended 48 (1.9) 48 (1.9) NA NA 72 (2.83) 72 (2.83) NA NA 94 (3.7) 94 (3.7) 48 (1.9) 48 (1.9) NA NA NA 72 (2.83) 72 (2.83) NA NA NA 94 (3.7) 94 (3.7) B (dia) C (dia) D (dia) 92.1 (3.62) 92.1 (3.62) 92.1 (3.62) 92.1 (3.62) 127 (5) 127 (5) 127 (5) 127 (5) 157.2 (6.2) 157.2 (6.2) 102 (4.02) 102 (4.02) 102 (4.02) 102 (4.02) 102 (4.02) 138 (5.43) 138 (5.43) 138 (5.43) 138 (5.43) 138 (5.43) 158 (6.22) 162 (6.38) 120.5 (4.74) 127 (5) 127 (5) 165 (6.5) 152.5 (6) 168.5 (6.63) 168.5 (6.63) 190.5 (7.5) 190.5 (7.5) 200.2 (7.88) 125 (4.92) 125 (4.92) 135 (5.31) 145 (5.71) 145 (5.71) 160 (6.3) 160 (6.3) 170 (6.7) 180 (7.08) 180 (7.08) 180 (7.08) 190 (7.48) 152.5 (6) 165 (6.5) 165 (6.5) 216 (8.5) 190.5 (7.5) 210 (8.26) 210 (8.26) 241 (9.48) 228.6 (9) 254 (10) 165 (6.5) 165 (6.5) 180 (7.08) 195 (7.67) 195 (7.67) 200 (7.87) 200 (7.87) 215 (8.46) 230 (9.05) 230 (9.05) 220 (8.66) 235 (9.25) E (dia) 20 (0.79) 20 (0.79) 20 (0.79) 26 (1.02) 20 (0.79) 22 (0.86) 22 (0.86) 26 (1.02) 20 (0.79) 22 (0.86) 18 (0.71) 18 (0.71) 22 (0.86) 26 (1.02) 26 (1.02) 18 (0.71) 18 (0.71) 22 (0.86) 26 (1.02) 26 (1.02) 18 (0.71) 22 (0.86) F 19.5 (0.77) 22.5 (0.88) 25.5 (1) 38.5 (1.51) 24 (0.94) 28.5 (1.12) 32 (1.26) 38.5 (1.51) 24 (0.94) 32 (1.26) 20 (0.79) 20 (0.79) 26 (1.02) 28 (1.1) 30 (1.18) 20 (0.79) 24 (0.94) 28 (1.1) 32 (1.26) 36 (1.42) 20 (0.79) 24 (0.94) G 9.5 (0.37) 9.5 (0.37) 9.5 (0.37) 9.5 (0.37) 9.5 (0.37) 9.5 (0.37) 9.5 (0.37) 9.5 (0.37) 9.5 (0.37) 9.5 (0.37) 9.5 (0.37) 9.5 (0.37) 9.5 (0.37) 9.5 (0.37) 9.5 (0.37) 9.5 (0.37) 9.5 (0.37) 9.5 (0.37) 9.5 (0.37) 9.5 (0.37) 9.5 (0.37) 9.5 (0.37) N of holes 4 8 8 8 4 8 8 8 8 8 4 4 4 4 4 8 8 8 8 8 8 8 13 2600T Pressure Transmitters Model 264DC, 264HC, 264NC SS/264XC_2 Electrical connections HART Version Internal ground termination point M+ - 0 2 3 4 7 6 5 9 60 40 20 0 Remote indicator 8 10 80 10 % 0 Kent-Taylor Line load M + 3 4 2 8 1 7 5 6 Harting pin (male) identification + + 250 ohm min GND TEST COMM - 691HT External ground termination point F1 F2 + Test points 4 to 20mA F3 - F4 PV REVIEW - + Power source CONF SERIAL LINK TRIM A B C Hand-held communicator D E F 2 3 M N O P Q R 4 5 6 S T U V W X Y Z # 7 8 9 @ % & / + - 0 Optional G H I 1 J K L Receiver HART hand-held communicator may be connected at any wiring termination point in the loop, providing the minimum resistance is 250 ohm. If this is less than 250 ohm, additional resistance should be added to allow communications FIELDBUS Versions 7/8" connector 1 3 2 4 Internal ground termination point M12 x 1 connector 2 1 3 Fieldbus line (polarity independent) BUS CONNECTIONS 4 PIN (male) IDENTIFICATION FOUNDATION PROFIBUS Fieldbus PA 1 FFPA+ 2 FF+ GROUND 3 SHIELD PA- 4 GROUND SHIELD Mating female plug NOT SUPPLIED 14 External ground termination point 2600T Pressure Transmitters Model 264DC, 264HC, 264NC SS/264XC_2 BASIC ORDERING INFORMATION model 264DC Differential /Gauge Pressure Transmitter with direct mount seal Select one character or set of characters from each category and specify complete catalog number. Refer to additional ordering information code and specify one or more codes for each transmitter if additional options are required. BASE MODEL - 1st to 5th characters 2 6 4 D C X X X X X X Continued Differential Gauge Pressure Transmitter with direct mount seal - BASE ACCURACY 0.075% SENSOR - Span limits - 6th 0.54 and 16 kPa 0.67 and 40kPa 1.1 and 65kPa 2.67 and 160kPa 10 and 600kPa 40 and 2400kPa 134 and 8000kPa 267 and 16000kPa character 5.4 and 160mbar 6.7 and 400mbar 11 and 650mbar 26.7 and 1600mbar 0.1 and 6bar 0.4 and 24bar 1.34 and 80bar 2.67 and 160bar E F G H M P Q S 2.14 and 64inH2O 2.67 and 160inH2O 4.35 and 260inH2O 10.7 and 642inH2O 1.45 and 87psi 5.8 and 348psi 19.4 and 1160psi 38.7 and 2320psi HIGH PRESSURE SIDE - Size/Mounting flange rating - 7th character 2in 2in 2in 2in 3in 3in food design 3in 3in 3in 4in 4in DN50 DN50 DN50 DN50 DN80 DN80 DN80 DN80 DN80 DN100 DN100 ANSI CL 150 ANSI CL 300 ANSI CL 600 ANSI CL 900 ANSI CL 150 ANSI CL 150 ANSI CL 300 ANSI CL 600 ANSI CL 900 ANSI CL 150 ANSI CL 300 DIN PN 16/40 DIN PN 64 DIN PN 100 DIN PN 160 DIN PN 16 DIN PN 40 DIN PN 64 DIN PN 100 DIN PN 160 DIN PN 16 DIN PN 40 A D G J B 1 E H K C F M P R W N L Q S Y T U HIGH PRESSURE SIDE - Mounting flange material/Seat form (seal) - 8th character Carbon steel Form RF (raised face) - serrated finish (Notes 1, 3) Carbon steel Form RF (raised face) - smooth finish (Notes 1, 3) Carbon steel DIN 2526 - Form C/E - serrated finish (Notes 2, 3) Carbon steel DIN 2526 - Form C/E - smooth finish (Notes 2, 3) AISI 316 ss Form RF (raised face) - serrated finish (Notes 1, 3) AISI 316 ss Form RF (raised face) - smooth finish (Note 1) AISI 316 ss DIN 2526 - Form C/E - serrated finish (Notes 2, 3) AISI 316 ss DIN 2526 - Form C/E - smooth finish (Notes 2, 3) HIGH PRESSURE SIDE - Extension length and material (wetted parts) - 9th character Flush (see next for diaphragm material) 50mm (2in) 50mm (2in) 100mm (4in) 100mm (4in) 150mm (6in) 150mm (6in) AISI 316 L ss Hastelloy C276TM AISI 316 L ss Hastelloy C276TM AISI 316 L ss Hastelloy C276TM (Notes 3, 4) (Notes 3, 4, 6) (Notes 3, 4) (Notes 3, 4, 6) (Notes 3, 4) (Notes 3, 4, 6) A B G P D E L Q NACE NACE NACE NACE NACE NACE NACE F 1 2 3 4 5 6 HIGH PRESSURE SIDE - Diaphragm material (wetted parts) (seal) - 10th character AISI 316 L ss Hastelloy C276TM Tantalum AISI 316 L ss with Teflon anti-stick coating Hastelloy C276TM with Teflon anti-stick coating AISI 316 L ss with Teflon coating anti-corrosion and anti-stick (Note 5) (Note 6) (Notes 6, 7) (Notes 5, 6, 8) (Notes 6, 8) (Notes 5, 6) NACE NACE NACE NACE NACE S H T K Y W HIGH PRESSURE SIDE - Fill fluid - 11th character Silicone oil Inert fluid - Galden Inert fluid - Halocarbon ABB fill Silicone oil for high temperature Silicone polymer for low temperature Mineral oil (FDA approved) Vegetable oil (FDA approved) Glycerin-Water (FDA approved) (Notes 3, 9) (Notes 3, 9) (Note 3) (Note 3) (Note 3) S N D K H C W A B 15 2600T Pressure Transmitters Model 264DC, 264HC, 264NC SS/264XC_2 BASIC ORDERING INFORMATION model 264DC X X X X X Low pressure side diaphragm material / Fill fluid (wetted parts) - 12th character AISI 316 L ss Silicone oil Silicone oil (one remote seal to be quoted separately) AISI 316 L ss (not wetted) Hastelloy C276TM (on AISI seat) Silicone oil Silicone oil Hastelloy C276TM Monel 400TM Silicone oil Tantalum Silicone oil AISI 316 L ss Inert fluid - Galden (Note 9) (Note 9) (one remote seal to be quoted separately) AISI 316 L ss (not wetted) Inert fluid - Galden Hastelloy C276TM (on AISI seat) Inert fluid - Galden (Note 9) (Note 9) Hastelloy C276TM Inert fluid - Galden Monel 400TM Inert fluid - Galden (Note 9) (Note 9) Tantalum Inert fluid - Galden Inert fluid - Halocarbon Note 9) AISI 316 L ss AISI 316 L ss (not wetted) Inert fluid - Halocarbon (Note 9) (one remote seal to be quoted separately) Inert fluid - Halocarbon (Note 9) Hastelloy C276TM (on AISI seat) Hastelloy C276TM Inert fluid - Halocarbon (Note 9) Monel 400TM Inert fluid - Halocarbon (Note 9) Tantalum Inert fluid - Halocarbon (Note 9) Low side process flanges/adapters material and connection (wetted parts) - 13th character AISI 316 L ss (Horizontal connection) AISI 316 L ss (Horizontal connection) Hastelloy C276TM (Horizontal connection) Hastelloy C276TM (Horizontal connection) Monel 400TM (Horizontal connection) Monel 400TM (Horizontal connection) AISI 316 closing flange for two seals construction 1 /4in NPT-f direct (7/16in UNF U.S. drilling) /2in NPT-f through adapter (7/16in UNF U.S. drilling) 1 /4in NPT-f direct (7/16in UNF U.S. drilling) 1 /2in NPT-f through adapter (7/16in UNF U.S. drilling) 1 /4in NPT-f direct (7/16in UNF U.S. drilling) 1 /2in NPT-f through adapter (7/16in UNF U.S. drilling) 1 NACE NACE NACE NACE NACE NACE NACE NACE NACE NACE NACE NACE (Note 10) (Note 10) (Note 10) (Note 10) (Note 10) (Note 10) (Note 11) NACE NACE NACE NACE NACE NACE NACE (Note 10) (Notes 9, 10) (Note 11) NACE NACE NACE S R H K M T A 2 B F C D L W Q P 4 5 A B D E G H R Bolts/Low side gasket (wetted parts) - 14th character AISI 316 ss (NACE) - (MWP = 16MPa) AISI 316 ss (NACE) - (MWP = 16MPa) AISI 316 ss (NACE) - (MWP = 16MPa) without gasket for two seals construction Housing material and electrical connection - 15th character Aluminium alloy (Barrel version) Aluminium alloy (Barrel version) Aluminium alloy (Barrel version) Aluminium alloy (Barrel version) Aluminium alloy (Barrel version) Aluminium alloy (Barrel version) Aluminium alloy copper-free (Barrel version) Aluminium alloy copper-free (Barrel version) Aluminium alloy copper-free (Barrel version) Aluminium alloy copper-free (Barrel version) Aluminium alloy copper-free (Barrel version) Aluminium alloy copper-free (Barrel version) AISI 316 L ss (Barrel version) AISI 316 L ss (Barrel version) AISI 316 L ss (Barrel version) AISI 316 L ss (Barrel version) AISI 316 L ss (Barrel version) Aluminium alloy (DIN version) Aluminium alloy (DIN version) Aluminium alloy (DIN version) Aluminium alloy (DIN version) VitonTM PTFE 1 /2in NPT M20 x 1.5 (CM 20) Pg 13.5 1 /2in GK Harting Han connector Fieldbus connector 1 /2in NPT M20 x 1.5 (CM 20) Pg 13.5 1 /2in GK Harting Han connector Fieldbus connector 1 /2in NPT M20 x 1.5 (CM20) Pg 13.5 1 /2in GK Fieldbus connector M20 x 1.5 (CM 20) Pg 13.5 Harting Han connector Fieldbus connector 3 4 R A B D C E G H L N M P R S T V U Z J Y K W (Note 12) (general purpose only) (Note 12) (general purpose only) (Note 12) (general purpose only) (Note 12) (general purpose only) (Note 12) (general purpose only) (general purpose only) (general purpose only) (Note 12) (general purpose only) (Note 12) (general purpose only) Output/Additional options - 16th character HART digital communication and 4 to 20mA HART digital communication and 4 to 20mA PROFIBUS PA PROFIBUS PA FOUNDATION Fieldbus FOUNDATION Fieldbus 16 No additional options Options requested (to be ordered by "Additional ordering code") No additional options Options requested (to be ordered by "Additional ordering code") No additional options Options requested (to be ordered by "Additional ordering code") (Notes 13, 14) (Note 13) (Notes 13, 14) (Note 14) (Notes 13, 14) (Note 14) H 1 P 2 F 3 2600T Pressure Transmitters Model 264DC, 264HC, 264NC SS/264XC_2 ADDITIONAL ORDERING INFORMATION for model 264DC Add one or more 2-digit code(s) after the basic ordering information to select all required options XX XX XX XX XX XX XX XX XX XX XX XX XX Drain/vent valve (material and position) (wetted parts) AISI 316 L ss on process axis (Note 15) NACE AISI 316 L ss on flange side top (Note 15) NACE AISI 316 L ss on flange side bottom (Note 15) NACE Hastelloy C276TM on process axis (Note 16) NACE Hastelloy C276TM on flange side top (Note 16) NACE Hastelloy C276TM on flange side bottom (Note 16) NACE Monel 400TM on process axis (Note 17) NACE Monel 400TM on flange side top (Note 17) NACE Monel 400TM on flange side bottom (Note 17) NACE Electrical certification ATEX Group II Category 1 GD - Intrinsic Safety EEx ia ATEX Group II Category 1/2 GD - Flameproof EEx d ATEX Group II Category 3 GD - Type of protection "N" EEx nL design compliance (Note 18) Canadian Standard Association (CSA) (only 1/2in NPT, M20 and Pg 13.5 housing) Intrinsic Safety-Flameproof to Standards Australia SAA Ex ia IIC T6/T5/T4 + Ex d II C T6/T5 (Note 18) Factory Mutual (FM) approval (only with 1/2in NPT, M20 and Pg 13.5 electrical connection) Output meter ProMeter, Standard calibration ProMeter, Special calibration Analog output indicator linear 0-100% scale Analog output indicator square root 0-10 scale Analog output indicator, special graduation (to be specified for linear scale) Analog output indicator, special graduation (to be specified for square root scale) Programmable signal meter and HART configurator (CoMeter) Programmable signal meter and HART configurator (CoMeter - customer configuration) Integral LCD Digital LCD integral display Surge Surge/Transient Protector (Note 18) (Note 18) (Note 18) (Note 18) (Note 18) (Note 18) (Note 18) (Note 18) V1 V2 V3 V4 V5 V6 V7 V8 V9 E1 E2 E3 E4 E5 E6 D1 D2 D3 D4 D5 D6 D7 D8 L1 (Note 18) Operating manual German Italian French Labels & tag language German Italian French Additional tag plate Laser printing of tag on stainless steel plate S1 M1 M2 M4 T1 T2 T4 I2 Configuration Standard - Pressure = inH2O/psi at 20 C; Temperature = deg. F Standard - Pressure = inH2O/psi at 4 C; Temperature = deg. F Standard - Pressure = inH2O/psi at 20 C; Temperature = deg.C Standard - Pressure = inH2O/psi at 4 C; Temperature = deg. C Custom Preparation procedure Oxygen service cleaning (only available with inert fill and PTFE gasket) - Pmax =12MPa for Galden or 9MPa for Halocarbon; Tmax =60 C/140 F Hydrogen service preparation Special services preparation N2 N3 N4 N5 N6 P1 P2 P4 Certificates Inspection certificate EN 10204-3.1.B of calibration (9-point) Certificate of compliance with the order EN 10204-2.1 of instrument design C1 C6 Material traceability Certificate of compliance with the order EN 10204-2.1 of process wetted parts Inspection certificate EN 10204-3.1.B of process wetted parts H1 H3 Connector Fieldbus 7/8 Fieldbus M12x1 Harting Han - straight entry Harting Han - angle entry (RECOMMENDED for FOUNDATION Fieldbus) (RECOMMENDED for PROFIBUS PA) (Notes 14, 19) (Notes 14, 19) (Notes 13, 19) (Notes 13, 19) U1 U2 U3 U4 17 2600T Pressure Transmitters Model 264DC, 264HC, 264NC SS/264XC_2 Note 1: Not available with DIN mounting flange code M, P, R, W, N, L, Q, S, Y, T, U Note 2: Not available with ANSI mounting flange code A, D, G, J, B, E, H, K, C, F Note 3: Not available with 3in ANSI CL150 food design size code 1 Note 4: Not available with ANSI CL 600 and CL 900 mounting flange rating code G, J, H, K and with DIN PN 64, PN 100 and PN 160 mounting flange rating code P, R, W, Q, S, Y Also not available with sensor code E combined with 2in or DN50 high side size code A, D, G, J, M, P, R, W. Note 5: Not available with Hastelloy C276 extension code 2, 4, 6 Note 6: Not available with serrated seat finish code A, G, D, L Note 7: Not available with extension code 1, 2, 3, 4, 5, 6 Note 8: Not available with 2in, DN50, DN80, DN100, mounting flange code A, D, G, J, M, P, R, W, N, L, Q, S, Y, T, U Note 9: Suitable for oxygen service Note 10: Not available with low side diaphragm code R, 2, W Note 11: Not available with low side diaphragm code S, H, K, M, T, A, B, F, C, D, L, Q, P, 4, 5 Note 12: Select type in additional ordering code Note 13: Not available with Electronic Housing code Z, R, G and W Note 14: Not available with Electronic Housing code P, E and K Note 15: Not available with Process flanges/adapters code D, E, G, H, R Note 16: Not available with Process flanges/adapters code A, B, G, H, R Note 17: Not available with Process flanges/adapters code A, B, D, E, R Note 18: Not available with PROFIBUS PA and FF output code 2 or 3 Note 19: Not available with Electronic housing code U, S, T, V, H, M, L, N, D, C, A, B, J, Y TM Hastelloy is a Cabot Corporation trademark TM Monel is an International Nickel Co. trademark TM Viton is a Dupont de Nemour trademark TM Galden is a Montefluos trademark TM Halocarbon is a Halocarbon Products Co. trademark Standard delivery items (can be differently specified by additional ordering code) - Adapters supplied loose - Plug on axis (no drain/vent valves) - General purpose (no electrical certification) - No meter/display, no mounting bracket, no surge protection - English manual and labels - Configuration with kPa and deg. C units - No test, inspection or material traceability certificates THE SELECTION OF SUITABLE WETTED PARTS AND FILLING FLUID FOR COMPATIBILITY WITH THE PROCESS MEDIA IS A CUSTOMER'S RESPONSIBILITY, IF NOT OTHERWISE NOTIFIED BEFORE MANUFACTURING. 18 2600T Pressure Transmitters Model 264DC, 264HC, 264NC SS/264XC_2 BASIC ORDERING INFORMATION model 264HC Gauge Pressure Transmitter with direct mount seal Select one character or set of characters from each category and specify complete catalog number. Refer to additional ordering information code and specify one or more codes for each transmitter if additional options are required. BASE MODEL - 1st to 5th characters 2 6 4 H C X X X X X X X Continued Gauge Pressure Transmitter with direct mount seal - BASE ACCURACY 0.075% SENSOR - Span limits - 6th character 1.1 and 65kPa 11 and 650mbar 2.67 and 160kPa 26.7 and 1600mbar 10 and 600kPa 0.1 and 6bar 40 and 2400kPa 0.4 and 24bar 134 and 8000kPa 1.34 and 80bar 267 and 16000kPa 2.67 and 160bar Diaphragm material/Fill Fluid (not wetted) - 7th character AISI 316 L ss Silicone oil AISI 316 L ss Inert fluid - Galden AISI 316 L ss Inert fluid - Halocarbon G H M P Q S 4.35 and 260inH2O 10.7 and 642inH2O 1.45 and 87psi 5.8 and 348psi 19.4 and 1160psi 38.7 and 2320psi R 2 W HIGH PRESSURE SIDE - Size/Mounting flange rating - 8th character 2in 2in 2in 2in 3in 3in food design 3in 3in 3in 4in 4in DN50 DN50 DN50 DN50 DN80 DN80 DN80 DN80 DN80 DN100 DN100 A D G J B 1 E H K C F M P R W N L Q S Y T U ANSI CL 150 ANSI CL 300 ANSI CL 600 ANSI CL 900 ANSI CL 150 ANSI CL 150 ANSI CL 300 ANSI CL 600 ANSI CL 900 ANSI CL 150 ANSI CL 300 DIN PN 16/40 DIN PN 64 DIN PN 100 DIN PN 160 DIN PN 16 DIN PN 40 DIN PN 64 DIN PN 100 DIN PN 160 DIN PN 16 DIN PN 40 HIGH PRESSURE SIDE - Mounting flange material/Seat form (seal) - 9th character Carbon steel Form RF (raised face) - serrated finish (Notes 1, 3) Carbon steel Form RF (raised face) - smooth finish (Notes 1, 3) Carbon steel DIN 2526 - Form C/E - serrated finish (Notes 2, 3) Carbon steel DIN 2526 - Form C/E - smooth finish (Notes 2, 3) AISI 316 ss Form RF (raised face) - serrated finish (Notes 1, 3) AISI 316 ss Form RF (raised face) - smooth finish (Note 1) AISI 316 ss DIN 2526 - Form C/E - serrated finish (Notes 2, 3) AISI 316 ss DIN 2526 - Form C/E - smooth finish (Notes 2, 3) th HIGH PRESSURE SIDE - Extension length and material (wetted parts) - 10 character Flush (see next for diaphragm material) 50mm (2in) 50mm (2in) 100mm (4in) 100mm (4in) 150mm (6in) 150mm (6in) AISI 316 L ss Hastelloy C276TM AISI 316 L ss Hastelloy C276TM AISI 316 L ss Hastelloy C276TM (Notes 3, 4) (Notes 3, 4, 6) (Notes 3, 4) (Notes 3, 4, 6) (Notes 3, 4) (Notes 3, 4, 6) A B G P D E L Q NACE NACE NACE NACE NACE NACE NACE F 1 2 3 4 5 6 HIGH PRESSURE SIDE - Diaphragm material (wetted parts) (seal) - 11th character AISI 316 L ss Hastelloy C276TM Tantalum AISI 316 L ss with Teflon anti-stick coating Hastelloy C276TM with Teflon anti-stick coating AISI 316 L ss with Teflon coating anti-corrosion and anti-stick (Note 5) (Note 6) (Notes 6, 7) (Notes 5, 6, 8) (Notes 6, 8) (Notes 5, 6) NACE NACE NACE NACE NACE S H T K Y W HIGH PRESSURE SIDE - Fill fluid - 12th character Silicone oil Inert fluid - Galden Inert fluid - Halocarbon ABB fill Silicone oil for high temperature Silicone polymer for low temperature Mineral oil (FDA approved) Vegetable oil (FDA approved) Glycerin-Water (FDA approved) (Notes 3, 9) (Notes 3, 9) (Note 3) (Note 3) (Note 3) S N D K H C W A B 19 2600T Pressure Transmitters Model 264DC, 264HC, 264NC SS/264XC_2 X BASIC ORDERING INFORMATION model 264HC X th Housing material and electrical connection - 13 character Aluminium alloy (Barrel version) Aluminium alloy (Barrel version) Aluminium alloy (Barrel version) Aluminium alloy (Barrel version) Aluminium alloy (Barrel version) Aluminium alloy (Barrel version) Aluminium alloy copper-free (Barrel version) Aluminium alloy copper-free (Barrel version) Aluminium alloy copper-free (Barrel version) Aluminium alloy copper-free (Barrel version) Aluminium alloy copper-free (Barrel version) Aluminium alloy copper-free (Barrel version) AISI 316 L ss (Barrel version) AISI 316 L ss (Barrel version) AISI 316 L ss (Barrel version) AISI 316 L ss (Barrel version) AISI 316 L ss (Barrel version) Output/Additional options - 14th character HART digital communication and 4 to 20mA HART digital communication and 4 to 20mA PROFIBUS PA PROFIBUS PA FOUNDATION Fieldbus FOUNDATION Fieldbus 20 1 /2in NPT M20 x 1.5 (CM 20) Pg 13.5 1 /2in GK Harting Han connector Fieldbus connector 1 /2in NPT M20 x 1.5 (CM 20) Pg 13.5 1 /2in GK Harting Han connector Fieldbus connector 1 /2in NPT M20 x 1.5 (CM20) Pg 13.5 1 /2in GK Fieldbus connector A B D C E G H L N M P R S T V U Z (Note 10) (general purpose only) (Note 10) (general purpose only) (Note 10) (general purpose only) (Note 10) (general purpose only) (Note 10) (general purpose only) No additional options Options requested (to be ordered by "Additional ordering code") No additional options Options requested (to be ordered by "Additional ordering code") No additional options Options requested (to be ordered by "Additional ordering code") (Notes 11, 12) (Note 11) (Notes 11, 12) (Note 12) (Notes 11, 12) (Note 12) H 1 P 2 F 3 2600T Pressure Transmitters Model 264DC, 264HC, 264NC SS/264XC_2 ADDITIONAL ORDERING INFORMATION for model 264HC Add one or more 2-digit code(s) after the basic ordering information to select all required options XX XX XX XX XX XX XX XX XX XX XX XX Electrical certification ATEX Group II Category 1 GD - Intrinsic Safety EEx ia ATEX Group II Category 1/2 GD - Flameproof EEx d ATEX Group II Category 3 GD - Type of protection "N" EEx nL design compliance (Note 13) Canadian Standard Association (CSA) (only 1/2in NPT, M20 and Pg 13.5 housing) Intrinsic Safety-Flameproof to Standards Australia SAA Ex ia IIC T6/T5/T4 + Ex d II C T6/T5 (Note 13) Factory Mutual (FM) approval (only with 1/2in NPT, M20 and Pg 13.5 electrical connection) Output meter ProMeter, Standard calibration ProMeter, Special calibration Analog output indicator linear 0-100% scale Analog output indicator, special graduation (to be specified for linear scale) Programmable signal meter and HART configurator (CoMeter) Programmable signal meter and HART configurator (CoMeter - customer configuration) Integral LCD Digital LCD integral display Surge Surge/Transient Protector (Note (Note (Note (Note (Note (Note 13) 13) 13) 13) 13) 13) E1 E2 E3 E4 E5 E6 D1 D2 D3 D5 D7 D8 L1 (Note 13) S1 Operating manual German Italian French Labels & tag language German Italian French Additional tag plate Laser printing of tag on stainless steel plate M1 M2 M4 T1 T2 T4 I2 Configuration Standard - Pressure = inH2O/psi at 20 C; Temperature = deg. F Standard - Pressure = inH2O/psi at 4 C; Temperature = deg. F Standard - Pressure = inH2O/psi at 20 C; Temperature = deg.C Standard - Pressure = inH2O/psi at 4 C; Temperature = deg. C Custom Preparation procedure Oxygen service cleaning (only available with inert fill) - Pmax =12MPa for Galden or 9MPa for Halocarbon; Tmax =60 C/140 F Hydrogen service preparation Special services preparation N2 N3 N4 N5 N6 P1 P2 P4 Certificates Inspection certificate EN 10204-3.1.B of calibration (9-point) Certificate of compliance with the order EN 10204-2.1 of instrument design C1 C6 Material traceability Certificate of compliance with the order EN 10204-2.1 of process wetted parts Inspection certificate EN 10204-3.1.B of process wetted parts H1 H3 Connector Fieldbus 7/8 Fieldbus M12x1 Harting Han - straight entry Harting Han - angle entry (RECOMMENDED for FOUNDATION Fieldbus) (RECOMMENDED for PROFIBUS PA) (Notes 12, 14) (Notes 12, 14) (Notes 11, 14) (Notes 11, 14) U1 U2 U3 U4 21 2600T Pressure Transmitters Model 264DC, 264HC, 264NC SS/264XC_2 Note 1: Not available with DIN mounting flange code M, P, R, W, N, L, Q, S, Y, T, U Note 2: Not available with ANSI mounting flange code A, D, G, J, B, E, H, K, C, F Note 3: Not available with 3in ANSI CL150 food design size code 1 Note 4: Not available with ANSI CL 600 and CL 900 mounting flange rating code G, J, H, K and with DIN PN 64, PN 100 and PN 160 mounting flange rating code P, R, W, Q, S, Y Note 5: Not available with Hastelloy C276 extension code 2, 4, 6 Note 6: Not available with serrated seat finish code A, G, D, L Note 7: Not available with extension code 1, 2, 3, 4, 5, 6 Note 8: Not available with 2in, DN50, DN80, DN100, mounting flange code A, D, G, J, M, P, R, W, N, L, Q, S, Y, T, U Note 9: Suitable for oxygen service Note 10: Select type in additional ordering code Note 11: Not available with Electronic Housing code Z, R, G Note 12: Not available with Electronic Housing code P, E Note 13: Not available with PROFIBUS PA and FF output code 2 or 3 Note 14 : Not available with Electronic housing code U, S, T, V, H, M, L, N, D, C, A, B TM Hastelloy is a Cabot Corporation trademark TM Galden is a Montefluos trademark TM Halocarbon is a Halocarbon Products Co. trademark Standard delivery items (can be differently specified by additional ordering code) - General purpose (no electrical certification) - No meter/display, no mounting bracket, no surge protection - English manual and labels - Configuration with kPa and deg. C units - No test, inspection or material traceability certificates THE SELECTION OF SUITABLE WETTED PARTS AND FILLING FLUID FOR COMPATIBILITY WITH THE PROCESS MEDIA IS A CUSTOMER'S RESPONSIBILITY, IF NOT OTHERWISE NOTIFIED BEFORE MANUFACTURING. 22 2600T Pressure Transmitters Model 264DC, 264HC, 264NC SS/264XC_2 BASIC ORDERING INFORMATION model 264NC Absolute Pressure Transmitter with direct mount seal Select one character or set of characters from each category and specify complete catalog number. Refer to additional ordering information code and specify one or more codes for each transmitter if additional options are required. BASE MODEL - 1st to 5th characters 2 6 4 N C X X X X X X X Continued Absolute Pressure Transmitter with direct mount seal - BASE ACCURACY 0.075% SENSOR - Span limits - 6th character 1.1 and 65kPa 11 and 650mbar 2.67 and 160kPa 26.7 and 1600mbar 10 and 600kPa 0.1 and 6bar 40 and 2400kPa 0.4 and 24bar 134 and 8000kPa 1.34 and 80bar 267 and 16000kPa 2.67 and 160bar Diaphragm material/Fill Fluid (not wetted) - 7th character AISI 316 L ss Silicone oil AISI 316 L ss Inert fluid - Galden AISI 316 L ss Inert fluid - Halocarbon 8 and 480mmHg 20 and 1200mmHg 1.45 and 87psi 5.8 and 348psi 19. 4 and 1160psi 38.7 and 2320psi G H M P Q S R 2 W HIGH PRESSURE SIDE - Size/Mounting flange rating - 8th character 2in 2in 2in 2in 3in 3in food design 3in 3in 3in 4in 4in DN50 DN50 DN50 DN50 DN80 DN80 DN80 DN80 DN80 DN100 DN100 A D G J B 1 E H K C F M P R W N L Q S Y T U ANSI CL 150 ANSI CL 300 ANSI CL 600 ANSI CL 900 ANSI CL 150 ANSI CL 150 ANSI CL 300 ANSI CL 600 ANSI CL 900 ANSI CL 150 ANSI CL 300 DIN PN 16/40 DIN PN 64 DIN PN 100 DIN PN 160 DIN PN 16 DIN PN 40 DIN PN 64 DIN PN 100 DIN PN 160 DIN PN 16 DIN PN 40 HIGH PRESSURE SIDE - Mounting flange material/Seat form (seal) - 9th character Carbon steel Form RF (raised face) - serrated finish (Notes 1, 3) Carbon steel Form RF (raised face) - smooth finish (Notes 1, 3) Carbon steel DIN 2526 - Form C/E - serrated finish (Notes 2, 3) Carbon steel DIN 2526 - Form C/E - smooth finish (Notes 2, 3) AISI 316 ss Form RF (raised face) - serrated finish (Notes 1, 3) AISI 316 ss Form RF (raised face) - smooth finish (Note 1) AISI 316 ss DIN 2526 - Form C/E - serrated finish (Notes 2, 3) AISI 316 ss DIN 2526 - Form C/E - smooth finish (Notes 2, 3) th HIGH PRESSURE SIDE - Extension length and material (wetted parts) - 10 character Flush (see next for diaphragm material) 50mm (2in) 50mm (2in) 100mm (4in) 100mm (4in) 150mm (6in) 150mm (6in) AISI 316 L ss Hastelloy C276TM AISI 316 L ss Hastelloy C276TM AISI 316 L ss Hastelloy C276TM (Notes 3, 4) (Notes 3, 4, 6) (Notes 3, 4) (Notes 3, 4, 6) (Notes 3, 4) (Notes 3, 4, 6) A B G P D E L Q NACE NACE NACE NACE NACE NACE NACE F 1 2 3 4 5 6 HIGH PRESSURE SIDE - Diaphragm material (wetted parts) (seal) - 11th character AISI 316 L ss Hastelloy C276TM Tantalum AISI 316 L ss with Teflon anti-stick coating Hastelloy C276TM with Teflon anti-stick coating AISI 316 L ss with Teflon coating anti-corrosion and anti-stick (Note 5) (Note 6) (Notes 6, 7) (Notes 5, 6, 8) (Notes 6, 8) (Notes 5, 6) NACE NACE NACE NACE NACE S H T K Y W HIGH PRESSURE SIDE - Fill fluid - 12th character Silicone oil Inert fluid - Galden Inert fluid - Halocarbon ABB fill Silicone oil for high temperature Silicone polymer for low temperature Mineral oil (FDA approved) Vegetable oil (FDA approved) Glycerin-Water (FDA approved) (Notes 3, 9) (Notes 3, 9) (Note 3) (Note 3) (Note 3) S N D K H C W A B 23 2600T Pressure Transmitters Model 264DC, 264HC, 264NC SS/264XC_2 X BASIC ORDERING INFORMATION model 264NC X th Housing material and electrical connection - 13 character Aluminium alloy (Barrel version) Aluminium alloy (Barrel version) Aluminium alloy (Barrel version) Aluminium alloy (Barrel version) Aluminium alloy (Barrel version) Aluminium alloy (Barrel version) Aluminium alloy copper-free (Barrel version) Aluminium alloy copper-free (Barrel version) Aluminium alloy copper-free (Barrel version) Aluminium alloy copper-free (Barrel version) Aluminium alloy copper-free (Barrel version) Aluminium alloy copper-free (Barrel version) AISI 316 L ss (Barrel version) AISI 316 L ss (Barrel version) AISI 316 L ss (Barrel version) AISI 316 L ss (Barrel version) AISI 316 L ss (Barrel version) Output/Additional options - 14th character HART digital communication and 4 to 20mA HART digital communication and 4 to 20mA PROFIBUS PA PROFIBUS PA FOUNDATION Fieldbus FOUNDATION Fieldbus 24 1 /2in NPT M20 x 1.5 (CM 20) Pg 13.5 1 /2in GK Harting Han connector Fieldbus connector 1 /2in NPT M20 x 1.5 (CM 20) Pg 13.5 1 /2in GK Harting Han connector Fieldbus connector 1 /2in NPT M20 x 1.5 (CM20) Pg 13.5 1 /2in GK Fieldbus connector A B D C E G H L N M P R S T V U Z (Note 10) (general purpose only) (Note 10) (general purpose only) (Note 10) (general purpose only) (Note 10) (general purpose only) (Note 10) (general purpose only) No additional options Options requested (to be ordered by "Additional ordering code") No additional options Options requested (to be ordered by "Additional ordering code") No additional options Options requested (to be ordered by "Additional ordering code") (Notes 11, 12) (Note 11) (Notes 11, 12) (Note 12) (Notes 11, 12) (Note 12) H 1 P 2 F 3 2600T Pressure Transmitters Model 264DC, 264HC, 264NC SS/264XC_2 ADDITIONAL ORDERING INFORMATION for model 264NC Add one or more 2-digit code(s) after the basic ordering information to select all required options XX XX XX XX XX XX XX XX XX XX XX XX Electrical certification ATEX Group II Category 1 GD - Intrinsic Safety EEx ia ATEX Group II Category 1/2 GD - Flameproof EEx d ATEX Group II Category 3 GD - Type of protection "N" EEx nL design compliance (Note 13) Canadian Standard Association (CSA) (only 1/2in NPT, M20 and Pg 13.5 housing) Intrinsic Safety-Flameproof to Standards Australia SAA Ex ia IIC T6/T5/T4 + Ex d II C T6/T5 (Note 13) Factory Mutual (FM) approval (only with 1/2in NPT, M20 and Pg 13.5 electrical connection) Output meter ProMeter, Standard calibration ProMeter, Special calibration Analog output indicator linear 0-100% scale Analog output indicator, special graduation (to be specified for linear scale) Programmable signal meter and HART configurator (CoMeter) Programmable signal meter and HART configurator (CoMeter - customer configuration) Integral LCD Digital LCD integral display Surge Surge/Transient Protector (Note (Note (Note (Note (Note (Note 13) 13) 13) 13) 13) 13) E1 E2 E3 E4 E5 E6 D1 D2 D3 D5 D7 D8 L1 (Note 13) S1 Operating manual German Italian French Labels & tag language German Italian French Additional tag plate Laser printing of tag on stainless steel plate M1 M2 M4 T1 T2 T4 I2 Configuration Standard - Pressure = inH2O/psi at 20 C; Temperature = deg. F Standard - Pressure = inH2O/psi at 4 C; Temperature = deg. F Standard - Pressure = inH2O/psi at 20 C; Temperature = deg.C Standard - Pressure = inH2O/psi at 4 C; Temperature = deg. C Custom Preparation procedure Oxygen service cleaning (only available with inert fill) - Pmax =12MPa for Galden or 9MPa for Halocarbon; Tmax =60 C/140 F Hydrogen service preparation Special services preparation N2 N3 N4 N5 N6 P1 P2 P4 Certificates Inspection certificate EN 10204-3.1.B of calibration (9-point) Certificate of compliance with the order EN 10204-2.1 of instrument design C1 C6 Material traceability Certificate of compliance with the order EN 10204-2.1 of process wetted parts Inspection certificate EN 10204-3.1.B of process wetted parts H1 H3 Connector Fieldbus 7/8 Fieldbus M12x1 Harting Han - straight entry Harting Han - angle entry (RECOMMENDED for FOUNDATION Fieldbus) (RECOMMENDED for PROFIBUS PA) (Notes 12, 14) (Notes 12, 14) (Notes 11, 14) (Notes 11, 14) U1 U2 U3 U4 25 2600T Pressure Transmitters Model 264DC, 264HC, 264NC SS/264XC_2 Note 1: Not available with DIN mounting flange code M, P, R, W, N, L, Q, S, Y, T, U Note 2: Not available with ANSI mounting flange code A, D, G, J, B, E, H, K, C, F Note 3: Not available with 3in ANSI CL150 food design size code 1 Note 4: Not available with ANSI CL 600 and CL 900 mounting flange rating code G, J, H, K and with DIN PN 64, PN 100 and PN 160 mounting flange rating code P, R, W, Q, S, Y Note 5: Not available with Hastelloy C276 extension code 2, 4, 6 Note 6: Not available with serrated seat finish code A, G, D, L Note 7: Not available with extension code 1, 2, 3, 4, 5, 6 Note 8: Not available with 2in, DN50, DN80, DN100, mounting flange code A, D, G, J, M, P, R, W, N, L, Q, S, Y, T, U Note 9: Suitable for oxygen service Note 10: Select type in additional ordering code Note 11: Not available with Electronic Housing code Z, R, G Note 12: Not available with Electronic Housing code P, E Note 13: Not available with PROFIBUS PA and FF output code 2 or 3 Note 14: Not available with Electronic housing code U, S, T, V, H, M, L, N, D, C, A, B TM Hastelloy is a Cabot Corporation trademark TM Galden is a Montefluos trademark TM Halocarbon is a Halocarbon Products Co. trademark Standard delivery items (can be differently specified by additional ordering code) - General purpose (no electrical certification) - No meter/display, no mounting bracket, no surge protection - English manual and labels - Configuration with kPa and deg. C units - No test, inspection or material traceability certificates THE SELECTION OF SUITABLE WETTED PARTS AND FILLING FLUID FOR COMPATIBILITY WITH THE PROCESS MEDIA IS A CUSTOMER'S RESPONSIBILITY, IF NOT OTHERWISE NOTIFIED BEFORE MANUFACTURING. 26 2600T Pressure Transmitters Model 264DC, 264HC, 264NC SS/264XC_2 27 2600T Pressure Transmitters Model 264DC, 264HC, 264NC SS/264XC_2 The Company's policy is one of continuous product improvement and the right is reserved to modify the information contained herein without notice. ABB has Sales & Customer Support expertise in over 100 countries worldwide Printed in Italy (01.04) www.abb.com/instrumentation SS/264XC_2 (c) ABB 2004 ABB Ltd Howard Road, St. Neots Cambridgeshire, PE19 3EU UK Tel: +44(0)1480 475321 Fax: +44(0)1480 217948 ABB Inc. 125 E. County Line Road Warminster, PA 18974 USA Tel: +1 215 674 6000 Fax: +1 215 674 7183 ABB SACE spa Business Unit Instrumentation Via Statale 113 22016 Lenno (CO) Italy Tel: +39 0344 58111 Fax: +39 0344 56278