1Doc. No. MD-1011, Rev. I© 2009 SCILLC. All rights reserved.
Characteristics subject to change without notice
FEATURES
Fast read access times:
– 90/120/150ns
Low power CMOS dissipation:
– Active: 25 mA max.
– Standby: 100 µµ
µµ
µA max.
Simple write operation:
– On-chip address and data latches
– Self-timed write cycle with auto-clear
Fast write cycle time:
– 5ms max.
CMOS and TTL compatible I/O
Hardware and software write protection
DESCRIPTION
The CAT28C64B is a fast, low power, 5V-only CMOS
Parallel EEPROM organized as 8K x 8-bits. It requires a
simple interface for in-system programming. On-chip
address and data latches, self-timed write cycle with
auto-clear and VCC power up/down write protection
eliminate additional timing and protection hardware.
DATA Polling and Toggle status bits signal the start and
end of the self-timed write cycle. Additionally, the
CAT28C64B features hardware and software write
protection.
BLOCK DIAGRAM
Commercial, industrial and automotive
temperature ranges
Automatic page write operation:
– 1 to 32 bytes in 5ms
– Page load timer
End of write detection:
– Toggle bit
DATADATA
DATADATA
DATA polling
100,000 program/erase cycles
100 year data retention
The CAT28C64B is manufactured using Catalyst’s
advanced CMOS floating gate technology. It is designed
to endure 100,000 program/erase cycles and has a data
retention of 100 years. The device is available in JEDEC-
approved 28-pin DIP, TSOP, SOIC, or, 32-pin PLCC
package .
ADDR. BUFFER
& LATCHES
ADDR. BUFFER
& LATCHES
INADVERTENT
WRITE
PROTECTION
CONTROL
LOGIC
TIMER
ROW
DECODER
COLUMN
DECODER
HIGH V OL TA GE
GENERATOR
A5A12
CE
OE
WE
A0A4
I/O0I/O7
I/O BUFFERS
8,192 x 8
EEPROM
ARRAY
32 BYTE PAGE
REGISTER
VCC
DATA POLLING
AND
TOGGLE BIT
64K-Bit CMOS PARALLEL EEPROM
CAT28C64B
CAT28C64B
2
Doc. No. MD-1011, Rev. I © 2009 SCILLC. All rights reserved.
Characteristics subject to change without notice
PIN CONFIGURATION
A6
A5
A4
A3
5
6
7
8
A2
A1
A0
NC
9
10
11
12
I/O013
A8
A9
A11
NC
29
28
27
26 OE
A10
CE
25
24
23
22 I/O7
21
I/O1
I/O2
VSS
NC
I/O3
I/O4
I/O5
14 15 16 17 18 19 20
4321323130
A7
A12
NC
NC
VCC
WE
NC
I/O6
TOP VIEW
I/O2
VSS
I/O6
I/O5
13
14
20
19
18
17
9
10
11
12
24
23
22
21
A1
A0
I/O0
I/O1
OE
A10
CE
I/O7
A5
A4
A3
A2
5
6
7
8
1
2
3
4
NC
A12
A7
A6A9
A11
28
27
26
25
VCC
WE
NC
A8
I/O4
I/O3
16
15
PLCC Package (N, G)
SOIC Package (J, W) (K, X)
DIP Package (P, L)
I/O2
VSS
I/O6
I/O5
13
14
20
19
18
17
9
10
11
12
24
23
22
21
A1
A0
I/O0
I/O1
OE
A10
CE
I/O7
A5
A4
A3
A2
5
6
7
8
1
2
3
4
NC
A12
A7
A6A9
A11
28
27
26
25
VCC
WE
NC
A8
I/O4
I/O3
16
15
TSOP Package (8mm x 13.4mm) (H13)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
28
27
26
25
24
23
22
21
20
19
18
17
I/O6
I/O5
I/O4
GND
I/O2
A1
A2
VCC
NC
WE
NC
A8
A9
A11
OE
A7
A6
A5
A4
A3
A10
I/O7
A12
16
15
CE
I/O3
I/O1
I/O0
A0
PIN FUNCTIONS
Pin Name Function Pin Name Function
A0A12 Address Inputs WE Write Enable
I/O0I/O7Data Inputs/Outputs VCC 5 V Supply
CE Chip Enable VSS Ground
OE Output Enable NC No Connect
CAT28C64B
3Doc. No. MD-1011, Rev. I
© 2009 SCILLC. All rights reserved.
Characteristics subject to change without notice
ABSOLUTE MAXIMUM RATINGS*
Temperature Under Bias ................. 55°C to +125°C
Storage Temperature....................... 65°C to +150°C
Voltage on Any Pin with
Respect to Ground(2) ........... 2.0V to +VCC + 2.0V
VCC with Respect to Ground ............... 2.0V to +7.0V
Package Power Dissipation
Capability (Ta = 25°C)................................... 1.0W
Lead Soldering Temperature (10 secs) ............ 300°C
Output Short Circuit Current(3) ........................ 100 mA
*COMMENT
Stresses above those listed under Absolute Maximum
Ratings may cause permanent damage to the device.
These are stress ratings only, and functional operation
of the device at these or any other conditions outside of
those listed in the operational sections of this specifica-
tion is not implied. Exposure to any absolute maximum
rating for extended periods may affect device perfor-
mance and reliability.
RELIABILITY CHARACTERISTICS
Symbol Parameter Min. Max. Units Test Method
NEND(1) Endurance 105Cycles/Byte MIL-STD-883, Test Method 1033
TDR(1) Data Retention 100 Years MIL-STD-883, Test Method 1008
VZAP(1) ESD Susceptibility 2000 Volts MIL-STD-883, Test Method 3015
ILTH(1)(4) Latch-Up 100 mA JEDEC Standard 17
Note:
(1) This parameter is tested initially and after a design or process change that affects the parameter.
(2) The minimum DC input voltage is 0.5V. During transitions, inputs may undershoot to 2.0V for periods of less than 20 ns. Maximum DC
voltage on output pins is VCC +0.5V, which may overshoot to VCC +2.0V for periods of less than 20 ns.
(3) Output shorted for no more than one second. No more than one output shorted at a time.
(4) Latch-up protection is provided for stresses up to 100mA on address and data pins from 1V to VCC +1V.
MODE SELECTION
Mode CE WE OE I/O Power
Read L H L DOUT ACTIVE
Byte Write (WE Controlled) L H DIN ACTIVE
Byte Write (CE Controlled) L H DIN ACTIVE
Standby, and Write Inhibit H X X High-Z STANDBY
Read and Write Inhibit X H H High-Z ACTIVE
CAPACITANCE TA = 25°C, f = 1.0 MHz, VCC = 5V
Symbol Test Max. Units Conditions
CI/O(1) Input/Output Capacitance 10 pF VI/O = 0V
CIN(1) Input Capacitance 6 pF VIN = 0V
CAT28C64B
4
Doc. No. MD-1011, Rev. I © 2009 SCILLC. All rights reserved.
Characteristics subject to change without notice
D.C. OPERATING CHARACTERISTICS
VCC = 5V ±10%, unless otherwise specified.
Limits
Symbol Parameter Min. Typ. Max. Units Test Conditions
ICC VCC Current (Operating, TTL) 30 mA CE = OE = VIL,
f = 1/tRC min, All I/Os Open
ICCC(1) VCC Current (Operating, CMOS) 25 mA CE = OE = VILC,
f = 1/tRC min, All I/Os Open
ISB VCC Current (Standby, TTL) 1 mA CE = VIH, All I/Os Open
ISBC(2) VCC Current (Standby, CMOS) 100 µACE = VIHC,
All I/Os Open
ILI Input Leakage Current 10 10 µAV
IN = GND to VCC
ILO Output Leakage Current 10 10 µAV
OUT = GND to VCC,
CE = VIH
VIH(2) High Level Input Voltage 2 VCC +0.3 V
VIL(1) Low Level Input Voltage 0.3 0.8 V
VOH High Level Output Voltage 2.4 V IOH = 400µA
VOL Low Level Output Voltage 0.4 V IOL = 2.1mA
VWI Write Inhibit Voltage 3.5 V
Note:
(1) VILC = 0.3V to +0.3V.
(2) VIHC = VCC 0.3V to VCC +0.3V.
CAT28C64B
5Doc. No. MD-1011, Rev. I
© 2009 SCILLC. All rights reserved.
Characteristics subject to change without notice
A.C. CHARACTERISTICS, Read Cycle
VCC = 5V ±10%, unless otherwise specified.
28C64B-90 28C64B-12 28C64B-15
Symbol Parameter Min. Max. Min. Max. Min. Max. Units
tRC Read Cycle Time 90 120 150 ns
tCE CE Access Time 90 120 150 ns
tAA Address Access Time 90 120 150 ns
tOE OE Access Time 50 60 70 ns
tLZ(1) CE Low to Active Output 0 0 0 ns
tOLZ(1) OE Low to Active Output 0 0 0 ns
tHZ(1)(2) CE High to High-Z Output 50 50 50 ns
tOHZ(1)(2) OE High to High-Z Output 50 50 50 ns
tOH(1) Output Hold from Address Change 0 0 0 ns
Figure 1. A.C. Testing Input/Output Waveform(3)
INPUT PULSE LEVELS REFERENCE POINTS
2.0 V
0.8 V
VCC - 0.3V
0.0 V
Figure 2. A.C. Testing Load Circuit (example)
Note:
(1) This parameter is tested initially and after a design or process change that affects the parameter.
(2) Output floating (High-Z) is defined as the state when the external data line is no longer driven by the output buffer.
(3) Input rise and fall times (10% and 90%) < 10 ns.
1.3V
DEVICE
UNDER
TEST
1N914
3.3K
CL = 100 pF
OUT
CL INCLUDES JIG CAPACITANCE
CAT28C64B
6
Doc. No. MD-1011, Rev. I © 2009 SCILLC. All rights reserved.
Characteristics subject to change without notice
A.C. CHARACTERISTICS, Write Cycle
VCC = 5V ±10%, unless otherwise specified.
28C64B-90 28C64B-12 28C64B-15
Symbol Parameter Min. Max. Min. Max. Min. Max. Units
tWC Write Cycle Time 5 5 5 ms
tAS Address Setup Time 0 0 0 ns
tAH Address Hold Time 100 100 100 ns
tCS CE Setup Time 0 0 0 ns
tCH CE Hold Time 0 0 0 ns
tCW(2) CE Pulse Time 110 110 110 ns
tOES OE Setup Time 0 0 0 ns
tOEH OE Hold Time 0 0 0 ns
tWP(2) WE Pulse Width 110 110 110 ns
tDS Data Setup Time 60 60 60 ns
tDH Data Hold Time 0 0 0 ns
tINIT(1) Write Inhibit Period After Power-up 5 10 5 10 5 10 ms
tBLC(1)(3) Byte Load Cycle Time .05 100 .05 100 .05 100 µs
Note:
(1) This parameter is tested initially and after a design or process change that affects the parameter.
(2) A write pulse of less than 20ns duration will not initiate a write cycle.
(3) A timer of duration tBLC max. begins with every LOW to HIGH transition of WE. If allowed to time out, a page or byte write will begin;
however a transition from HIGH to LOW within tBLC max. stops the timer.
CAT28C64B
7Doc. No. MD-1011, Rev. I
© 2009 SCILLC. All rights reserved.
Characteristics subject to change without notice
Byte Write
A write cycle is executed when both CE and WE are low,
and OE is high. Write cycles can be initiated using either
WE or CE, with the address input being latched on the
falling edge of WE or CE, whichever occurs last. Data,
conversely, is latched on the rising edge of WE or CE,
whichever occurs first. Once initiated, a byte write cycle
automatically erases the addressed byte and the new
data is written within 5 ms.
DEVICE OPERATION
Read
Data stored in the CAT28C64B is transferred to the data
bus when WE is held high, and both OE and CE are held
low. The data bus is set to a high impedance state when
either CE or OE goes high. This 2-line control architec-
ture can be used to eliminate bus contention in a system
environment.
Figure 3. Read Cycle
Figure 4. Byte Write Cycle [WE Controlled]
ADDRESS
CE
OE
WE
DATA OUT
tAS
DATA IN D A TA VALID
HIGH-Z
tCS
tAH tCH
tWC
tOEH
tBLC
tOES tWP
ADDRESS
CE
OE
WE
tRC
DATA OUT D A TA V ALIDD A TA V ALID
tCE
tOE
tOH
tAA
tOHZ
tHZ
VIH
HIGH-Z
tLZ
tOLZ
CAT28C64B
8
Doc. No. MD-1011, Rev. I © 2009 SCILLC. All rights reserved.
Characteristics subject to change without notice
ADDRESS
CE
OE
WE
DATA OUT
tAS
DATA IN D A TA V ALID
HIGH-Z
tAH
tWC
tOEH
tDH
tDS
tOES
tBLC
tCH
tCS
tCW
Page Write
The page write mode of the CAT28C64B (essentially an
extended BYTE WRITE mode) allows from 1 to 32 bytes
of data to be programmed within a single EEPROM write
cycle. This effectively reduces the byte-write time by a
factor of 32.
Following an initial WRITE operation (WE pulsed low, for
tWP, and then high) the page write mode can begin by
issuing sequential WE pulses, which load the address
and data bytes into a 32 byte temporary buffer. The page
address where data is to be written, specified by bits A5
to A12, is latched on the last falling edge of WE. Each
byte within the page is defined by address bits A0 to A4
(which can be loaded in any order) during the first and
subsequent write cycles. Each successive byte load
cycle must begin within tBLC MAX of the rising edge of the
preceding WE pulse. There is no page write window
limitation as long as WE is pulsed low within tBLC MAX.
Upon completion of the page write sequence, WE must
stay high a minimum of tBLC MAX for the internal auto-
matic program cycle to commence. This programming
cycle consists of an erase cycle, which erases any data
that existed in each addressed cell, and a write cycle,
which writes new data back into the cell. A page write will
only write data to the locations that were addressed and
will not rewrite the entire page.
Figure 5. Byte Write Cycle [CE Controlled]
Figure 6. Page Mode Write Cycle
OE
CE
WE
ADDRESS
I/O
tWP tBLC
BYTE 0 BYTE 1 BYTE 2 BYTE n BYTE n+1 BYTE n+2
LAST BYTE
tWC
CAT28C64B
9Doc. No. MD-1011, Rev. I
© 2009 SCILLC. All rights reserved.
Characteristics subject to change without notice
WE
CE
OE
I/O6
tOEH tOE tOES
tWC
(1) (1)
DATA Polling
DATA polling is provided to indicate the completion of
write cycle. Once a byte write or page write cycle is
initiated, attempting to read the last byte written will
output the complement of that data on I/O7 (I/O0I/O6
are indeterminate) until the programming cycle is com-
plete. Upon completion of the self-timed write cycle, all
I/Os will output true data during a read cycle.
Toggle Bit
In addition to the DATA Polling feature, the device offers
an additional method for determining the completion of
a write cycle. While a write cycle is in progress, reading
data from the device will result in I/O6 toggling between
one and zero. However, once the write is complete, I/O6
stops toggling and valid data can be read from the
device.
Figure 7. DATA Polling
Figure 8. Toggle Bit
Note:
(1) Beginning and ending state of I/O6 is indeterminate.
ADDRESS
CE
WE
OE
I/O7DIN = X DOUT = X DOUT = X
tOE
tOEH
tWC
tOES
CAT28C64B
10
Doc. No. MD-1011, Rev. I © 2009 SCILLC. All rights reserved.
Characteristics subject to change without notice
SOFTWARE DATA
PRO TECTION A CTIV A TED (1)
WRITE DATA: XX
WRITE LAST BYTE
TO
LAST ADDRESS
TO ANY ADDRESS
WRITE DATA: AA
ADDRESS: 1555
WRITE DATA: 55
ADDRESS: 0AAA
WRITE DATA: A0
ADDRESS: 1555
Note:
(1) Write protection is activated at this point whether or not any more writes are completed. Writing to addresses must occur within tBLC
Max., after SDP activation.
HARDWARE DATA PROTECTION
The following is a list of hardware data protection features
that are incorporated into the CAT28C64B.
(1) VCC sense provides for write protection when VCC
falls below 3.5V min.
(2) A power on delay mechanism, tINIT (see AC
characteristics), provides a 5 to 10 ms delay before
a write sequence, after VCC has reached 3.5V min.
(3) Write inhibit is activated by holding any one of OE
low, CE high or WE high.
(4) Noise pulses of less than 20 ns on the WE or CE
inputs will not result in a write cycle.
SOFTWARE DATA PROTECTION
The CAT28C64B features a software controlled data
protection scheme which, once enabled, requires a data
algorithm to be issued to the device before a write can be
performed. The device is shipped from Catalyst with the
software protection NOT ENABLED (the CAT28C64B is
in the standard operating mode).
Figure 9. Write Sequence for Activating Software
Data Protection Figure 10. Write Sequence for Deactivating
Software Data Protection
WRITE DATA: AA
ADDRESS: 1555
WRITE DATA: 55
ADDRESS: 0AAA
WRITE DATA: 80
ADDRESS: 1555
WRITE DATA: AA
ADDRESS: 1555
WRITE DATA: 55
ADDRESS: 0AAA
WRITE DATA: 20
ADDRESS: 1555
CAT28C64B
11 Doc. No. MD-1011, Rev. I
© 2009 SCILLC. All rights reserved.
Characteristics subject to change without notice
To activate the software data protection, the device must
be sent three write commands to specific addresses with
specific data (Figure 9). This sequence of commands
(along with subsequent writes) must adhere to the page
write timing specifications (Figure 11). Once this is done,
all subsequent byte or page writes to the device must be
preceded by this same set of write commands. The data
protection mechanism is activated until a deactivate
sequence is issued regardless of power on/off transitions.
This gives the user added inadvertent write protection
on power-up in addition to the hardware protection
provided.
To allow the user the ability to program the device with
an EEPROM programmer (or for testing purposes) there
is a software command sequence for deactivating the
data protection. The six step algorithm (Figure 10) will
reset the internal protection circuitry, and the device will
return to standard operating mode (Figure 12 provides
reset timing). After the sixth byte of this reset sequence
has been issued, standard byte or page writing can
commence.
Figure 11. Software Data Protection Timing
CE
WE
tWP
AA
1555 55
0AAA A0
1555
DATA
ADDRESS
tBLC
tWC
BYTE OR
PAGE
WRITES
ENABLED
Figure 12. Resetting Software Data Protection Timing
CE
WE
AA
1555 55
0AAA
DATA
ADDRESS tWC80
1555 AA
1555 55
0AAA 20
1555 SDP
RESET
DEVICE
UNPROTECTED
Speed
90: 90ns
12: 120ns
15: 150ns
CAT28C64B
12
Doc. No. MD-1011, Rev. I © 2009 SCILLC. All rights reserved.
Characteristics subject to change without notice
EXAMPLE OF ORDERING INFORMATION(1)
Prefix Device # Suffix
28C64B
Product
Number
CAT
Optional
Company
ID
NI T
Tape & Reel
Package
P: PDIP
(2)
J: SOIC (JEDEC)
(2)
K: SOIC (EIAJ)
(2)
N: PLCC
(2)
-15
Temperature Range
Blank = Commercial (0˚C to +70˚C)
I = Industrial (-40˚C to +85˚C)
A = Automotive (-40˚ to +105˚C)
(3)
Speed
12: 120ns
15: 150ns
L: PDIP (Lead free, Halogen free)
W: SOIC (JEDEC) (Lead free, Halogen free)
X: SOIC (EIAJ) (Lead free, Halogen free)
G: PLCC (Lead free, Halogen free)
H13: TSOP (8mmx13.4mm) (Lead free, Halogen free)
90: 90ns
ORDERING INFORMATION
Notes:
(1) The device used in the above example is a CAT28C64BNI-15T (PLCC, Industrial temperature, 150 ns Access Time, Tape & Reel).
(2) Solder-plate (tin-lead) packages, contact Factory for availability.
(3) -40°C to +125°C is available upon request.
srebmuNtraPelbaredrO )seciveDeerF-bProf(
T21-IGB46C82TAC21ALB46C82TAC
T51-IGB46C82TAC51ALB46C82TAC
T09-IGB46C82TAC09ALB46C82TAC
T21-AGB46C82TACT21-IWB46C82TAC
T51-AGB46C82TACT51-IWB46C82TAC
T09-AGB46C82TACT09-IWB46C82TAC
T21I31HB46C82TACT21-AWB46C82TAC
T51I31HB46C82TACT51-AWB46C82TAC
T09I31HB46C82TACT09-AWB46C82TAC
T21A31HB46C82TACT21-IXB46C82TAC
T51A31HB46C82TACT51-IXB46C82TAC
T09A31HB46C82TACT09-IXB46C82TAC
21ILB46C82TACT21-AXB46C82TAC
51ILB46C82TACT51-AXB46C82TAC
09ILB46C82TACT09-AXB46C82TAC
CAT28C64B
13 Doc. No. MD-1011, Rev. I
© 2009 SCILLC. All rights reserved.
Characteristics subject to change without notice
REVISION HISTORY
etaDnoisiveRnoitpircseD
40-raM-92B .saerallanisegakcapneerGdeddA
40-rpA-91C
noitangisedteehsatadeteleD margaiDkcolBetadpU noitamrofnIgniredrOetadpU yrotsiHnoisiveRetadpU rebmuNveRetadpU
40-voN-61D noitamrofnIgniredrOotdeepssn09:09ddA
50-beF-82E noitamrofnIgniredrOtidE
50-raM-81F noitpircseDtidE
80-tcO-51G .egakcapbPnS)mm4.31xmm8(POSTetanimilE
80-voN-91H rotcudnocimeSNOottnirpenifdnaogolegnahC
90-luJ-82I noitamrofnIgniredrOfoelpmaxEetadpU elbatnoitamrofnIgniredrOetadpU
ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to
any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising
out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages.
Typical parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All
operating parameters, including Typicals must be validated for each customer application by customers technical experts. SCILLC does not convey any license under its patent rights nor the rights
of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications
intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should
Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates,
and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death
associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal
Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
LITERATURE FULFILLMENT:
Literature Distribution Center for ON Semiconductor
P.O. Box 5163, Denver, Colorado 80217 USA
Phone: 303-675-2175 or 800-344-3860 Toll Free USA/Canada
Fax: 303-675-2176 or 800-344-3867 Toll Free USA/Canada
Email: orderlit@onsemi.com
N. American Technical Support: 800-282-9855
Toll Free
USA/Canada
Europe, Middle East and Africa Technical Support:
Phone: 421 33 790 2910
Japan Customer Focus Center:
Phone: 81-3-5773-3850
ON Semiconductor Website: www.onsemi.com
Order Literature: http://www.onsemi.com/orderlit
For additional information, please contact your local
Sales Representative