107-68358
Packaging 04May09 Rev M
Specification
2.5MM PITCH BATTERY CONN
1. PURPOSE 目的
目的目的
目的
Define the packaging specifiction and packaging method of 2.5MM PITCH BATTERY CONN.
订定 2.5MM PITCH BATTERY CONN 产品之包装规格及包装方式。
2. APPLICABLE PRODUCT 适用范围
适用范围适用范围
适用范围
Tyco P/N. Description
1939246-1 2.5MM PITCH BATTERY REC. DIP, V, PACKING
1717478-1/2 SMD ASSY FOR QD CONNECTION SYSTEM
1674231-1 REC ASSY 2.5MM PITCH BATTERY CONN
1-1674231-1 REC ASSY 2.5MM PITCH BATTERY CONN
1565860-1 RECEPTACLE ASSEMBLY FOR 2.5mm PITCH BATTERY CONNECTOR
1473776-7 RECEPTACLE ASSY FOR 2.5MM PITCH BATTERY CONN
1-1473776-7 RECEPTACLE ASSY FOR 2.5MM PITCH BATTERY CONN
1674430-1 REC ASSY REVERSE TYPE 2.5MM PITCH BATTERY CONNECTOR
1717620-1 REC ASSY 8POS.R/A DIP TYPE 2.5mm PITCH BATTERY CONNECTOR
1746798-1 REC ASSY 8POS,R/A DIP REVERSE TYPE 2.5MM PITCH BATTERY CONNECTOR
3. PACKAGING MATERIAL 包装材料
包装材料包装材料
包装材料
Package Part No. Description Size(LxWxH) Usage
INNER 1-912023-5 PS TRAY 335X230X23.8 7/600
8-912068-9 INNER BOX TYPE-6 340X240X84 1/600
1-623124-0 DESICCANT 25g 2/600
995265-2 PE BAG 508x381 1/600
623853-1 PE film 25w 6.5 MR/600
3-912074-2 URETHANE CUSHION 315X200X7 2/600
623865-4 INNER LABEL 95X76 1/600
4-912011-6 CARTON C-32 490X350X172 1/2400
912065-2 AIR CAP 1100X390X4 1/2400
623865-1 OUTER LABEL 102X102 1/2400
DR CHK APVD
Sam Wu Ocean Tang Ansin Yang
Tyco Electronics AMP Guangdong Ltd. * Trademark
East Rongqi Road, | Indicates change
Ronggui Town, Shunde, Foshan,
Guangdong, P.R. China
QR-ME-030B
1 of 3
MIDDLE
OUTER
LOC FR
107-68358
3. PACKAGING MATERIAL 包装材料
包装材料包装材料
包装材料
Inner Middle
LABEL - 623865-4
SEALING Tape Tape
4.PACKAGING QUANTITY 包装数量
包装数量包装数量
包装数量
Inner Middle
QTY
5. PACKING METHOD 包装方法
包装方法包装方法
包装方法
5.1. Load connectors qty as 4 all oriented same way into tray.
按4中指定数量朝同一方向放产品入TRAY中。
图
图图
图 1
1717478-1的摆放方向如上图所示
的摆放方向如上图所示的摆放方向如上图所示
的摆放方向如上图所示
5.2. Place another tray onto previous tray with products.and ensure the two trays are
justification completely.
盖上另一个装满产品的TRAY，保证上下两个TRAY完全对齐。
5.3. Stack 6 trays with contacts one by one, then put an empty tray.
将装好产品的6个 TRAY 堆成一叠，最后在上面放一个空 TRAY。
5.4. Wrap 7 stacked with tape.
将堆成一叠的七个TRAY用胶带固定。
注:如图2示，缠三道，每道约三圈。
图
图图
图 2
Rev M QR-ME-030B 2 of 3
Outer
623865-1
100 pcs/tray 600 pcs/inner box
Tape
Outer
600X4=2400 pcs/carton
107-68358
5. PACKING METHOD 包装方法
包装方法包装方法
包装方法
5.5.Place one stack with 7 trays into the polybag and place two bags of desiccant(1-623124-0)
on top of tray & heat-seal it.
将一叠TRAY(7个tray)放入袋子中并在TRAY的上面放二包干燥剂(1-623124-0)，然后热封其袋口。
5.6. Set up an inner box.
折叠好一个内盒。
5.7. Place a foam to bottom of inner box, and ensure under edge of tray don't pin cushion.
在内盒的底部放一块海绵，保证 TRAY 的下部边缘不压住海绵。
5.8. Place one bag of trays with full of connectors into the inner box & place 1 cushion on top of tray.
将一袋装满产品的TRAY放入内盒中，并在TRAY的上面放1块海绵。
5.9. Close cover of the inner box, place tape on the middle of three sides.
合上合盖，并在内盒三边的中间(除连接边外)各贴上一条大胶带。
5.10. Place an inner label to the middle of cover of inner box.
在盒盖的中间贴上内标签。
5.11. Set up a carton and secure bottom flaps with tape.
折叠好一个外箱，并用胶带封好箱底。
5.12. Spread one piece of air cap and put into the carton, air cap facing outside.
展开一块气泡垫并将其放入箱中，气泡面朝外。
5.13. Put 4 inner boxes full of products into the carton and muffle 4 inner boxes with air cap.
再将4个装满产品的内盒放入外箱中，并用气泡将四个内盒裹住。
5.14. Seal the box with tape. And place product identification label in "product id" marked on box.
用胶带封箱，在箱外印有“PRODUCT ID”标识处贴上外标签。
Rev M QR-ME-030B 3 of 3