MATRIX Transceiver Modules ZMXM-400 Series Integrated Transceiver Module for ZigBee / IEEE 802.15.4 N O T FO R R EC N O EW M M D EN ES D IG ED N Evaluation Kits available DESCRIPTION The Matrix module is a 2.4 GHz IEEE 802.15.4 RF transceiver providing a cost- effective solution for data links and wireless networks. The module design is based on the IEEE 802.15.4 standard and supports peer-to-peer, star, and mesh networking. The Matrix module is offered with two transmitter output power options, either 10mW or 100mW, providing for enhanced range performance over standard IEEE 802.15.4/ZigBee implementations with the integrated power amplifier. Additionally, each module offers a Dynamic Power Configuration capability giving the ability to bypass the power amplifier for a 1mW power output when low power operation is imperative. The Matrix module consists of the Texas Instruments CC2430, 10mW or 100mW Power Amplifier, and integrated PCB trace antenna. The module has the option to be populated with a MMCX connector for use with an external cabled antenna. The module is FCC, IC, and CE certified for fast and simple integration into end applications. The Matrix modules provide the lowest cost, best in class performance, in a compact form factor. FEATURES * Supports LS Research or Z-StackTM protocols * 17 General Purpose I/O ports * Miniature Footprint: 10mW ( 23.4 x 28.7 mm) 100mW (23.4 x 31.2 mm) * Windows(R) Based Test Tools * Integrated certified PCB trace antenna * Optional MMCX connector for external antenna * 16 RF channels (Channel 16 operates at reduced power levels) * Long Range: 10mW - up to 2000 feet 100mW - up to 4000 feet * Serial UART interface * Lowest Power Consumption * Compliance Certification: 10mW - FCC (USA), IC (Canada), and CE (Europe) certification 100mW - FCC (USA) and IC (Canada) certification * RoHS compliant * Output power software controlled: 1mW - 10mW or 1mW - 100mW The information in this document is subject to change without notice, please confirm data is current Document No: 0004-00-07-00-000 (Issue C) Date Published: December 4, 2009 ZMXM-400 Series MATRIX MODULES ORDERING INFORMATION Part Number Order Number ZMXM-400-1 Matrix 10mW Matrix 10mW transceiver module PCB Trace Antenna ZMXM-400-1-B Matrix 10mW transceiver module PCB Trace Antenna Bulk (1 tray) ZMXM-400-1C Matrix 10mW transceiver MMCX connector installed ZMXM-400-1C-B Matrix 10mW transceiver MMCX connector installed Bulk (1 tray) ZMXM-400-KIT-2 10mW Matrix Module Kit Mins/Mults Status 180 pcs / 180 pcs Not Recommended For New Design 36 pcs / 36 pcs Not Recommended For New Design 1,040 pcs / 180 pcs Not Recommended For New Design N O T FO R R EC N O EW M M D EN ES D IG ED N ZMXM-400 Description N/A Discontinued 1 Not Recommended For New Design Matrix 100mW transceiver module PCB Trace Antenna N/A Discontinued ZMXM-401-1-B Matrix 100mW transceiver module PCB Trace Antenna Bulk (1 tray) N/A Discontinued ZMXM-401-1C Matrix 100mW transceiver module PCB Trace Antenna MMCX connector installed N/A Discontinued ZMXM-401-1C-B Matrix 100mW transceiver module PCB Trace Antenna MMCX connector installed Bulk (1 tray) N/A Discontinued ZMXM-401-1 Matrix 100mW ZMXM-401 ZMXM-400 Series ABSOLUTE MAXIMUM RATINGS Rating Value Unit 3.6 Vdc VDD + 0.3, Max 3.6 Vdc +10 dBm -45 to 125 C Power Supply Voltage Voltage on Any Digital Pin RF Input Power N O T FO R R EC N O EW M M D EN ES D IG ED N Storage Temperature Range Note: Exceeding the maximum ratings may cause permanent damage to the module or devices. Caution: Matrix modules are sensitive to electrostatic discharge, observe precautions when handling. OPERATING CONDITIONS Characteristic Min Typ Max Unit 10mW 2.1 3.3 3.6 Vdc 100mW 2.4 3.3 3.6 Vdc 2480 MHz Power Supply Voltage (Vdd) Input Frequency Ambient Temperature Range 2405 85 C Logic Input Low Voltage -40 0 25 30% Vdd V Logic Input High Voltage 70% Vdd Vdd V ZMXM-400 Series ELECTRICAL SPECIFICATIONS (@ 25 C, Vdd = 3.3V, unless otherwise noted) Parameter Min RF Frequency Range RF Data Rate Host Data Rate 2400 General Charcteristics Typ 250 10 mW 100 mW Unit 2483.5 MHz kbps 115.2 115.2 kbps kbps 128 8 kB kB 10mW 100mW 50 130 mA mA 10mW 100mW 33 33 mA mA N O T FO R R EC N O EW M M D EN ES D IG ED N Flash Memory RAM Max Power Consumption Transmit Mode Receive Mode Standby Mode 10mW 100mW 5 5 A A 35 dBm dBm dBm dB % Transmitter Nominal Output Power 10mW 100mW Nominal Output Power (DPS) Programmable Output Power range Error Vector Magnitude 10 20 -1 24 12 Receiver Module Sensitivity (1% PER) Receiver Sensitivity (1% PER) Saturation (Maximum Input Level) (1% PER) Control AC Characteristics RESET_N low pulse width Interrupt request pulse width Control DC Characteristics Logic Input Low Logic Input High Logic Output Low Logic Output High I/O pin pull-up and pull-down resistor 0 -89 -92 10 dBm dBm dBm 2.5 31.25 0 VDD-0.25 0 VDD-0.25 17 ns ns 0.7 VDD 0 VDD 20 0.9 VDD 0.25 VDD 23 V V V V k Note: Please refer to the Texas Instruments CC2430 datasheet for further information and details regarding the configuration of the I/O ports. ZMXM-400 Series PIN SIGNALS I/O PORT CONFIGURATION PIN 8 PIN 17 Matrix modules have 24 edge I/O interfaces for connection to the host board. Figure 1 shows the layout of the 24 edge castellations. PIN 16 PIN 24 PIN 9 PIN 1 N O T FO R R EC N O EW M M D EN ES D IG ED N Figure 1 I/O pin assignments Pin # Name Type Description 1 GROUND GND 2 P0_2 DI/DO/AI General Purpose Digital I/0 Port 0_2 or ADC input 2 3 P0_3 DI/DO/AI General Purpose Digital I/0 Port 0_3 or ADC input 3 4 P0_4 DI/DO/AI General Purpose Digital I/0 Port 0_4 or ADC input 4 5 P0_5 DI/DO/AI General Purpose Digital I/0 Port 0_5 or ADC input 5 6 P0_6 DI/DO/AI General Purpose Digital I/0 Port 0_6 or ADC input 6 7 P0_7 DI/DO/AI General Purpose Digital I/0 Port 0_7 or ADC input 7 8 GROUND GND Ground 9 MODE0 DI/DO General Purpose Digital I/O Port 2_2 or Debug CLK 10 MODE1 DI/DO General Purpose Digital I/O Port 2_1 or Debug DATA (DD) 11 MODE2 DI/DO General Purpose Digital I/O Port 2_0 12 P1_7 DI/DO General Purpose Digital I/O Port 1_7 13 P1_6 DI/DO General Purpose Digital I/O Port 1_6 14 TXD DI/DO General Purpose Digital I/O Port 1_5 or Application Transmit Data Output 15 RXD DI/DO General Purpose Digital I/O Port 1_4 or Application Receive Data Input Ground 16 P1_3 DI/DO General Purpose Digital I/O Port 1_3 17 GROUND GND Ground 18 P1_1 DI/DO General Purpose Digital I/O Port 1_1, 20mA drive capability 19 P1_0 DI/DO 20 RESET DI 21 P0_0 DI/DO/AI General Purpose Digital I/0 Port 0_0 or ADC input 0 Optional on-board Green LED 22 P0_1 DI/DO/AI General Purpose Digital I/0 Port 0_1 or ADC input 1Optional on-board Red LED 23 VDD PI 24 GROUND GND General Purpose Digital I/O Port 1_0, 20mA drive capability Reset, active low Power Supply Input Ground Unused I/O pins should be left unconnected and the pin state set via the Host Protocol. DI = Digital Input PI = Power Input DO = Digital Output GND = Ground AI = Analog Input AO = Analog Output ZMXM-400 Series ANTENNA The Matrix module includes an integrated PCB trace antenna. An optional configuration with a MMCX connector is also available. The module regulatory certification has been completed with the PCB trace antenna and also with a Nearson (part# S131CL-5-RMM-2450S) dipole antenna on a 5 inch cable using the MMCX connection. The integrated PCB antenna topology is an F-antenna. This antenna is used because it is reasonably compact, has a fairly omni-directional radiation pattern, good efficiency, and is very simple. An adequate ground plane directly beneath the module but not under the antenna is necessary to provide good efficiency. N O T FO R R EC N O EW M M D EN ES D IG ED N The antenna radiation patterns are dependent upon the carrier board the Matrix module is placed upon. Measured radiation patterns of the module alone are available by contacting LS Research. The environment the module is placed in will dictate the range performance. The non-ideal characteristics of the transmission channel result in the transmitted signal producing reflection, diffraction, and/or scattering. All of these factors randomly combine to create extremely complex scenarios. It is also best to keep some clearance between the antenna and nearby objects. This includes how the module is mounted in the product enclosure. Unless the items on the following list of recommendations are met, the radiation pattern can be heavily distorted. * Never place ground plane or copper trace routing underneath the antenna. * Never place the antenna very close to metallic objects. * In the final product, ensure that any wiring or other components do not get too close to the antenna. * The antenna will need a reasonable ground plane area on the mother board area to be efficient. * Do not use a metallic enclosure or metallized plastic for the antenna. * Try to keep any plastic enclosure greater than 1 cm from the antenna in any orientation. POWER AMPLIFIER Both variants of the Matrix modules contain a Power Amplifier. The Matrix 10 mW (ZMXM-400) has a maximum Power Out of 10 mW, while the Matrix 100 mW has a maximum Power Out of 100 mW. The Power Amplifier is controlled via the P1_2 General Purpose I/O (GPIO) of the Texas Instruments CC2430. As such, the P1_2 GPIO needs to be configured as an output in the application source code to enable control the Power Amplifier. When P1_2 drives LOW (i.e. logic level `0') the Power Amplifier is disabled and maximum Power Out is 1 mW regardless of module in use. When P1_2 drives HIGH (i.e. logic level `1') the Power Amplifier is enabled and maximum Power Out is either 10 mW or 100 mW depending upon which variant of the Matrix module is in use. Intermediate power level settings (i.e. between 1 mW and 10 or 100 mW) may be achieved by enabling the power amplifier and then varying the Power Out of the CC2430. ZMXM-400 Series DIMENSIONS: ZMXM-400-1 Matrix Module 10mW Dimensions in inches. Tolerances = +/-0.005" unless otherwise noted. PCB Trace Antenna 0.920 0.194 PIN 24: GROUND RF Shield X3 P0_2 + 3.3V P0_3 P0_1 P0_4 P0_0 P0_5 RESET P0_6 P1_0 P0_7 P1_1 PIN 8: GROUND PIN 16: P1_3 RXD TXD P1_6 P1_7 MODE 2 MODE 1 PIN 17: GROUND PIN 9: MODE 0 0.060 1.130 0.655 N O T FO R R EC N O EW M M D EN ES D IG ED N PIN 1: GROUND DIMENSIONS: ZMXM-400-1C Matrix Module 10mW with Optional MMCX Connector Dimensions in inches. Tolerances = +/-0.005" unless otherwise noted. Optional MMCX Connector for external antenna Overall Height w/MMCX Connector 0.920 0.415 0.203 J2 J2 X3 P0_2 + 3.3V P0_3 P0_1 P0_4 P0_0 P0_5 RESET P0_6 P1_0 P0_7 P1_1 PIN 8: GROUND PIN 16: P1_3 RXD TXD P1_6 P1_7 MODE 2 MODE 1 0.060 PIN 17: GROUND PIN 9: MODE 0 RF Shield PIN 24: GROUND 1.130 0.655 PIN 1: GROUND ZMXM-400 Series DIMENSIONS: ZMXM-401-1 Matrix Module 100mW Dimensions in inches. Tolerances = +/-0.005" unless otherwise noted. PCB Trace Antenna 0.920 0.194 0.768 RF Shield X3 P0_2 + 3.3V P0_3 P0_1 P0_4 P0_0 P0_5 RESET P0_6 P1_0 P0_7 P1_1 PIN 8: GROUND PIN 16: P1_3 RXD TXD P1_6 P1_7 MODE 2 MODE 1 PIN 17: GROUND PIN 9: MODE 0 0.060 1.230 PIN 24: GROUND N O T FO R R EC N O EW M M D EN ES D IG ED N PIN 1: GROUND DIMENSIONS: ZMXM-401-1C Matrix Module 100mW with Optional MMCX Connector Dimensions in inches. Tolerances = +/-0.005" unless otherwise noted. Optional MMCX Connector for external antenna Overall Height w/MMCX Connector 0.920 0.415 0.203 J2 J2 X3 P0_2 + 3.3 V P0_3 P0_1 P0_4 P0_0 P0_5 RESET P0_6 P1_0 P0_7 P1_1 PIN 8: GROUND PIN 16: P1_3 RXD TXD P1_6 P1_7 MODE 2 MODE 1 0.060 PIN 17: GROUND PIN 9: MODE 0 RF Shield PIN 24: GROUND 1.230 0.768 PIN 1: GROUND ZMXM-400 Series PCB PAD Layout Dimensions in inches. Tolerances = +/-0.005" unless otherwise noted. 0.455 0.455 PIN 1 PIN 24 0.700 0.080 Typ 24 Pads N O T FO R R EC N O EW M M D EN ES D IG ED N 0.005 0.085 0.080 0.085 Typ 24 Pads 0.085 0.105 0.100 Pitch Typ PCB Keep- Out Areas 0.105 Dimensions in inches. Tolerances = +/-0.005" unless otherwise noted. Matrix Module 10mW Matrix Module 100mW Minimum PCB Trace, Plane and Component Keep-Out Area, All Layers PIN 1 PIN 1 PIN 24 Exposed PCB Trace Top Layer Keep-Out Area Note: 0.185 Recommended Host PCB Edge 0.270 0.230 0.270 0.230 0.205 0.080 PIN 24 0.175 0.260 Recommended Host PCB Edge 0.175 Minimum PCB Trace, Plane & Component Keep-Out Area, All Layers 0.345 0.990 0.345 0.990 Exposed PCB Trace Top Layer Keep-Out Area Matrix modules should be mounted so the antenna is overhanging the board edge. This will provide the best antenna performance for the PCB trace antenna. It is also recommended to have a ground plane on the host board underneath the rest of the module, up to the recommended PCB edge. This will improve the antenna performance by increasing the overall ground plane. Traces can be run underneath the Matrix module on the host PCB as long a there is an uninterrupted ground plane on one layer as well. CEL can arrange guidance and help with the host PCB layout. ZMXM-400 Series AGENCY SAFETY CERTIFICATIONS FCC Part 15.247 Module Certified (Portable) The Matrix modules comply with Part 15 of the Federal Communications Commission rules and regulations. To meet the FCC Certification requirements, the user must meet these regulations. * The text on the FCC ID label provided with the module is placed on the outside of the final product. N O T FO R R EC N O EW M M D EN ES D IG ED N * The modules may only use the antennas that have been tested and approved with this module. -- The on-board PCB trace antenna -- Nearson S131CL-5-RMM-2450S antenna. Per section 2.1091, the Matrix module has been certified by the FCC for use with other products without additional certification. Any modifications to this product may violate the rules of the Federal Communications Commission and make operation of the product unlawful. Per sections 15.107 and 15.109, the user's end product must be tested to comply with unintentional radiators for compliance. Per Section 47 C.F.R. Sec.15.105(b), the Matrix module is certified as a portable device for the FCC radiation exposure limits set forth for an uncontrolled environment. The antenna used with this module must be installed to provide a separation distance of at least 8 inches (20cm) from all persons. If the module is to be used in a handheld application, the user is responsible for passing the additional FCC part 2.1091 rules (SAR) and FCC Guidelines for Human Exposure to Radio Frequency Electromagnetic Fields, OET Bulletin and Supplement C. IC Certification -- Canada Matrix modules are IC certified. The labeling requirements for Industry Canada are similar to those of the FCC. A visible label on the outside of the final product must display the IC labeling. The user is responsible for the end product to comply with IC ICES-003 (Unintentional radiators). CE Certification -- Europe Matrix modules are EN 300-328-1 certified in Europe. The user must ensure compliance of the final product with the European harmonized EMC and safety standards. Annex II of the R&TTE Directive provides the requirements for the issuance of a Declaration of Conformity. The CE marking must be affixed legibly and indelibly to a visible location on the user's product. FCC Approved Antennas * Integrated PCB trace antenna * Nearson S131CL-5-RMM-2450S - A 2.4GHz Dipole antenna with a 5 inch cable and a right angle MMCX connector. ZMXM-400 Series SHIPMENT, HANDLING, AND STORAGE Shipment Matrix Modules are delivered in single piece, or 50 piece cartons in individual anti-static bags. Handling Matrix Modules are designed and packaged to be processed in an automated assembly line. !Warning Matrix Modules contain highly sensitive electronic circuitry. Handling without proper ESD protection may N O T FO R R EC N O EW M M D EN ES D IG ED N destroy or damage the module permanently. !Warning According to JEDEC ISP, Matrix Modules are moisture sensitive devices. Appropriate handling instructions and precautions are summarized in Section 2.1. Read carefully to prevent permanent damages due to moisture intake. Moisture Sensitivity Level (MSL) MSL 3, per J-STD-033 Storage Storage/Shelf life in sealed bags is 12 months at <40C and <90% relative humidity. PROCESSING Reflow Soldering A convection soldering oven is recommended over the infrared radiation type oven. Convection ovens allow more precise temperature control, and more even heating of parts regardless of material composition, thickness, or color. Preheat Phase Initial heating of component leads and solder paste balls, for removal of residual humidity. Note: The preheat phase is not intended to replace prior baking procedures. * Temperature rise rate: 0.8-1.7C/sec Note: Excessive slumping can result if the temperature rise is too rapid. * Time: 60-120 seconds Note: If the preheat is insufficient, large solder balls tend to be generated. Conversely, if preheat is excessive, small and large balls will be generated in clusters. * End Temperature: 150-200C Heating/Relow Phase The temperature rises above the liquidus temperature of the solder paste selected. Avoid a sudden rise in temperature as any slump of the solder paste could become worse. * Limit time above liquidus temperature to 35-90 seconds. * Peak reflow temperature: 230-250C ZMXM-400 Series PROCESSING (Continued) Cooling Phase A controlled cooling phase avoids unwanted metallurgical effects of the solder, and possible mechanical tensions in the products. Controlled cooling helps achieve the brightest possible solder fillets with a good shape and low contact angle. * Temperature fall rate: max 3C/sec Pb-Free Soldering Paste N O T FO R R EC N O EW M M D EN ES D IG ED N Use of "No Clean" soldering paste is strongly recommended, as it does not require cleaning after the soldering process. The pastes listed in the examples below meet these criteria. Soldering Paste: Indium 5.1 (Indium Corporation of America) Alloy Specification: SAC305 - Sn Zinc 96.5%/Ag Silver 3.0%/Cu Copper 0.5% Alloy Specification: SAC387 - Sn Zinc 95.5%/Ag Silver 3.8%/Cu Copper 0.7% Melting Temperature: 217C Soldering Paste: LFSOLDER TLF-206-93F (Tamura Kaken [UK] Ltd.) Alloy Specification: Sn Zinc 95.5%/Ag Silver 3.9%/Cu Copper 0.6% Melting Temperature: 216-221C The final choice of the soldering paste depends on individual factory approved manufacturing procedures. Stencil Thickness: 150 m for host boards Note: The quality of the solder joints on the castellations (`half vias') where they contact the host board should meet the appropriate IPC specification. See IPC-A-610-12.2.4. Cleaning In general, cleaning the populated modules is strongly discouraged. Residuals under the module cannot be easily removed with any cleaning process. * Cleaning with water can lead to capillary effects where water is absorbed into the gap between the host board and the module. The combination of soldering flux residuals and encapsulated water could lead to short circuits between neighboring pads. Water could also damage any stickers or labels. * Cleaning with alcohol or a similar organic solvent will likely flood soldering flux residuals into the two housings, which is not accessible for post-washing inspection. The solvent could also damage any stickers or labels. * Ultrasonic cleaning could damage the module permanently. The best approach is to consider using a "no clean" soldering paste and eliminate the post soldering cleaning step. ZMXM-400 Series PROCESSING (Continued) Optical Inspection After soldering the Module to the host board, consider optical inspection to check the following: * Proper alignment and centering of the module over the pads. * Proper solder joints on all pads. * Excessive solder or contacts to neighboring pads, or vias. N O T FO R R EC N O EW M M D EN ES D IG ED N Repeating Reflow Soldering Only a single reflow soldering process is encouraged for host boards. Wave Soldering If a wave soldering process is required on the host boards due to the presents of leaded components, only a single wave soldering process is encouraged. Hand Soldering Hand soldering is possible. Use a soldering iron temperature setting equivalent to 350C, follow IPC recommendations/ reference document IPC-7711. Rework Matrix Modules can be unsoldered from the host board. Use of a hot air re-work tool and hot plate for pre-heating from underneath is recommended. Avoid overheating. !Warning - Never attempt a rework on the module itself, e.g. replacing individual components. Such actions will terminate warranty coverage. Additional Grounding Attempts to improve module or system grounding by soldering braids, wires, or cables onto the module RF shield cover is done at the customers own risk. The numerous ground pins at the module perimeter should be sufficient for optimum immunity to external RF interference. Conformal Coating Conformal coating may be necessary in certain applications. Please note that the RF shield and the sticker prevent optimum inflow of liquids or aerosols. ZMXM-400 Series REVISION HISTORY & Disclaimer Revision History Previous Versions Changes to Current Version Initial advance datasheet. 0004-00-07-00-000 (Issue C) December 4, 2009 Updated Miniature Footprint dimensions for 100mW on front page and dimension drawings for 100mW, corrected the certification status under features, corrected J1 to J2 in the ordering information section, updated reflow soldering process specs (temperature rise time and limit time above liquius temerature), add Power Ampifier section on page 5, updated published date and Issue to C, removed preliminary datasheet from front page and added revision history and disclaimer to last page of datasheet. N O T FO R R EC N O EW M M D EN ES D IG ED N 0004-00-07-00-000 (Issue B) (Preliminary) May 07, 2008 Disclaimer * The information in this document is current as of the published date. The information is subject to change without notice. For actual design-in, refer to the latest publications of CEL data sheets or data books, etc., for the most up-to-date specifications of CEL products. Not all products and/or types are available in every country. Please check with an CEL sales representative for availability and additional information. * No part of this document may be copied or reproduced in any form or by any means without the prior written consent of CEL. CEL assumes no responsibility for any errors that may appear in this document. * CEL does not assume any liability for infringement of patents, copyrights or other intellectual property rights of third parties by or arising from the use of CEL products listed in this document or any other liability arising from the use of such products. No license, express, implied or otherwise, is granted under any patents, copyrights or other intellectual property rights of CEL or others. * Descriptions of circuits, software and other related information in this document are provided for illustrative purposes in semiconductor product operation and application examples. The incorporation of these circuits, software and information in the design of a customer's *equipment shall be done under the full responsibility of the customer. CEL assumes no responsibility for any losses incurred by customers or third parties arising from the use of these circuits, software and information. * While CEL endeavors to enhance the quality, reliability and safety of CEL products, customers agree and acknowledge that the possibility of defects thereof cannot be eliminated entirely. To minimize risks of damage to property or injury (including death) to persons arising from defects in CEL products, customers must incorporate sufficient safety measures in their design, such as redundancy, fire-containment and anti-failure features. Page N/A 1,5,7, 10,13