February 2010 Doc ID 11455 Rev 8 1/22
22
VN808-E
Octal channel high side driver
Features
VCC/2 compatible input
Junction overtemperature protection
Case overtemperature protection for thermal
independence of the channels
Current limitation
Shorted load protection
Undervoltage shut-down
Protection against loss of ground
Very low stand-by current
Compliance to 61000-4-4 IEC test up to 4 kV
Description
The VN808-E is a monolithic device designed in
STMicroelectronics VIPower M0-3 technology,
intended for driving any kind of load with one side
connected to ground.
Active current limitation combined with thermal
shutdown and automatic restart, protect the
device against overload. In overload condition,
channel turns OFF and back ON automatically so
as to maintain junction temperature between TTSD
and TR. If this condition makes case temperature
reach TCSD, overloaded channel is turned OFF
and will restart only when case temperature has
decreased down to TCR(see waveform 3 Figure 8
on page 11). Non overloaded channels continue
to operate normally. Device automatically turns
OFF in case of ground pin disconnection. This
device is especially suitable for industrial
applications conform to IEC 61131
Type RDS(on) (1)
1. Per channel
Iout (1) VCC
VN808-E 150 mΩ 0.7 A 45 V
PowerSO-36
www.st.com
Contents VN808-E
2/22 Doc ID 11455 Rev 8
Contents
1 Maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
2 Electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
3 Pin connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
4 Current, voltage conventions and internal diagram . . . . . . . . . . . . . . . 8
5 Switching time waveforms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
6 Reverse polarity protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
7 Package mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
7.1 Footprint recommended data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
7.2 Tube shipment information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
7.3 Tape and reel shipment information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
8 Order codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
9 Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
VN808-E Maximum ratings
Doc ID 11455 Rev 8 3/22
1 Maximum ratings
Table 1. Absolute maximum rating
Symbol Parameter Value Unit
VCC DC supply voltage 45 V
-IGND
DC ground pin reverse current
TRAN ground pin reverse current
(pulse duration < 1ms)
-250
-6
mA
A
IOUT DC output current Internally limited A
-IOUT Reverse DC output current -2 A
IIN DC input current ± 10 mA
VIN Input voltage range -3/+VCC V
VESD Electrostatic discharge (R = 1.5 kΩ; C = 100 pF) 2000 V
PTOT Power dissipation at Tc = 25 °C 96 W
LMAX
Max inductive load (VCC = 24 V, RLOAD = 48 Ω,
TA = 100 °C) 2H
TJJunction operating temperature Internally limited °C
TCCase operating temperature Internally limited °C
TSTG Storage temperature -40 to 150 °C
Table 2. Thermal data
Symbol Parameter Value Unit
RthJC Thermal resistance junction-case Max 1.3 °C/W
RthJA Thermal resistance junction-ambient (1)
1. When mounted on FR4 printed circuit board with 0.5 cm2 of copper area (at least 35 μm think) connected to
all TAB pins.
Max 50 °C/W
Electrical characteristics VN808-E
4/22 Doc ID 11455 Rev 8
2 Electrical characteristics
(10.5 V < VCC < 32 V; -40 °C < TJ < 125 °C; unless otherwise specified)
Table 3. Power section
Symbol Parameter Test conditions Min Typ Max Unit
VCC
Operating supply
voltage 10.5 45 V
VUSD
Undervoltage
shutdown 710.5V
RON On state resistance IOUT = 0.5 A; TJ = 25 °C
IOUT = 0.5 A;
150 185
280
mΩ
mΩ
ISSupply current
OFF state; VCC = 24 V;
TCASE = 25 °C
ON state (all channels ON);
VCC = 24 V, TCASE = 100 °C
150
12
μA
mA
ILGND
Output current at
turn-off
VCC = VSTAT = VIN = VGND = 24 V
VOUT = 0 V 1mA
IL(off)
OFF state output
current VIN = VOUT = 0 V; 05μA
VOUT(off)
OFF state output
voltage VIN = 0 V, IOUT = 0 A 3 V
td(Vccon)
Power-on delay time
from VCC rising edge Figure 7 on page 10 1ms
Table 4. Switching (VCC = 24 V)
Symbol Parameter Test conditions Min Typ Max Unit
tON Turn-on time RL = 48 Ω from 80%
VOUT Figure 6. 50 100 μs
tOFF Turn-off time RL = 48 Ω to 10% VOUT Figure 6. 75 150 μs
dVOUT/dt(on) Turn-on voltage slope RL = 48 Ω from VOUT = 2.4 V to
VOUT = 19.2 V Figure 6. 0.7 Vs
dVOUT/dt(off) Turn-off voltage slope RL = 48 Ω from VOUT = 21.6 V to
VOUT = 2.4 V Figure 6. 1.5 Vs
VN808-E Electrical characteristics
Doc ID 11455 Rev 8 5/22
Table 5. Input pin
Symbol Parameter Test conditions Min Typ Max Unit
VINL Input low level VCC /2-1 V
IINL
Low level input
current VIN = VCC / 2 - 1 V 80 μΑ
VINH Input high level VCC /2+1 V
IINH
High level input
current VIN = VCC / 2 + 1 V 150 260 μΑ
VI(HYST)
Input hysteresis
voltage 0.6 V
IIN Input current VIN = VCC = 32 V 300 μΑ
Table 6. Protections
Symbol Parameter Test conditions Min Typ Max Unit
TCSD
Case shut-down
temperature 125 130 135 °C
TCR
Case reset
temperature
110 °C
TCHYST
Case thermal
hysteresis 715 °C
TTSD
Junction shutdown
temperature 150 175 200 °C
TR
Junction reset
temperature 135 °C
THYST
Junction thermal
hysteresis 715 °C
Ilim
DC short circuit
current per channel VCC = 24 V; RLOAD = 10 mΩ0.7 1.7 A
Vdemag
Turn-off output clamp
voltage IOUT = 0.5 A; L = 6 mH VCC-57 VCC-52 VCC-47 V
Table 7. Status pin
Symbol Parameter Test conditions Min Typ Max Unit
IHSTAT
High level output
current
VCC = 18...32 V; RSTAT = 1 kΩ
(Fault condition) 234mA
ILSTAT Leakage current Normal operation; VCC = 32 V 0.1 μA
VCLSTAT Clamp voltage ISTAT = 1 mA
ISTAT = -1 mA
6.0 6.8
-0.7
8.0 V
V
Pin connections VN808-E
6/22 Doc ID 11455 Rev 8
3 Pin connections
Figure 2. Connection diagram (top view)
Table 8. Pin functions
Pin N°Symbol Function
TAB V CC Positive power supply voltage
1V
CC Positive power supply voltage
2,3,4,5 NC Not connected
6 Input 1 Input of channel 1
7 Input 2 Input of channel 2
8 Input 3 Input of channel 3
9 Input 4 Input of channel 4
10 Input 5 Input of channel 5
11 Input 6 Input of channel 6
12 Input 7 Input of channel 7
13 Input 8 Input of channel 8
14,15,16,17,18 NC Not connected
19 GND Logic ground
20 STATUS Common open source diagnostic for overtemperature
21,22 Output 8 High-side output of channel 8
23,24 Output 7 High-side output of channel 7
25, 26 Output 6 High-side output of channel 6
VN808-E Pin connections
Doc ID 11455 Rev 8 7/22
27. 28 Output 5 High-side output of channel 5
29, 30 Output 4 High-side output of channel 4
31, 32 Output 3 High-side output of channel 3
33, 34 Output 2 High-side output of channel 2
35, 36 Output 1 High-side output of channel 1
Table 8. Pin functions (continued)
Pin N°Symbol Function
Current, voltage conventions and internal diagram VN808-E
8/22 Doc ID 11455 Rev 8
4 Current, voltage conventions and internal diagram
Figure 3. Current and voltage conventions
Figure 4. Equivalent internal block diagram (same structure for all channel)
OUTn
GND
INn
VCC
STATUS
50V
50V
52V
6.8V
13
Ω
110k
Ω
VN808-E Current, voltage conventions and internal diagram
Doc ID 11455 Rev 8 9/22
Figure 5. Application example
Table 9. Truth table
Conditions INPUTn OUTPUTn STATUS
Normal operation L
H
L
H
L
L
Current limitation L
H
L
X
L
L
Overtemperature
(see waveforms 3, 4 Figure 8) -> TJ > TTSD
L
H
L
L
L
H
Undervoltage L
H
L
L
X
X
Vcc24V - 28,2V I EC6 11 31
22µF 100nF
Load 1
Load 2
Load 3
Load 8
VN808
Status
Vin 1
Vin 2
Vin 8
Vin 3
Imax 80µA
Load 1
Load 2
Load 3
Load 8
VN808
Status
Vin 1
Vin 2
Vin 8
Vin 3
Imax 80µA
22µF 100nF
Vcc24V - 28,2V I EC6 11 31
22µF 100nF
Load 1
Load 2
Load 3
Load 8
VN808
Status
Vin 1
Vin 2
Vin 8
Vin 3
Imax 80µA
Load 1
Load 2
Load 3
Load 8
VN808
Status
Vin 1
Vin 2
Vin 8
Vin 3
Imax 80µA
Load 1
Load 2
Load 3
Load 8
VN808
Status
Vin 1
Vin 2
Vin 8
Vin 3
Imax 80µA
22µF 100nF
Vcc24V - 28,2V I EC6 11 31
22µF 100nF
Load 1
Load 2
Load 3
Load 8
VN808
Status
Vin 1
Vin 2
Vin 8
Vin 3
Imax 80µA
Load 1
Load 2
Load 3
Load 8
VN808
Status
Vin 1
Vin 2
Vin 8
Vin 3
Imax 80µA
Load 1
Load 2
Load 3
Load 8
VN808
Status
Vin 1
Vin 2
Vin 8
Vin 3
Imax 80µA
Load 1
Load 2
Load 3
Load 8
VN808
Status
Vin 1
Vin 2
Vin 8
Vin 3
Imax 80µA 10nF
.
..
.....
.
.
RGNDRGND
Vcc24V - 28,2V I EC6 11 31
10nF
Vcc/2 compatible inputs
.
..
.....
.
.
RGNDRGND
Vcc24V - 28,2V I EC6 11 31
22µF 100nF
Vcc24V - 28,2V I EC6 11 31
22µF 100nF
Vcc24V - 28,2V I EC6 11 31
22µF 100nF
22µF 100nF
Load 1
Load 2
Load 3
Load 8
VN808
Status
Vin 1
Vin 2
Vin 8
Vin 3
Imax 80µA
Load 1
Load 2
Load 3
Load 8
VN808
Status
Vin 1
Vin 2
Vin 8
Vin 3
Imax 80µA
Load 1
Load 2
Load 3
Load 8
VN808-E
Status
Vin 1
Vin 2
Vin 8
Vin 3
Imax 80µA
Filter for bus inductance effect.,
Make supply voltage stable and
Avoid undervoltage shut-down EMC filter
Protection for IEC 61000-4-5
Surge test suggested 1,5KE39xx
Optional protection for
VCC disconnection.
Protection against
IEC 61000-4-6
Current injection test
10Ωprotection against disconnection
On inductive loads
PROTECTIONS INCLUDED IN THE DEVICE:
IEC 61000-4-2 ESD test better than 2kV Human Body Model – IEC 61000-4-4 Burst test
Status output current
From 2 to 4 mA
Switching time waveforms VN808-E
10/22 Doc ID 11455 Rev 8
5 Switching time waveforms
Figure 6. Turn-ON and turn-OFF
Figure 7. VCC turn-ON
VN808-E Switching time waveforms
Doc ID 11455 Rev 8 11/22
Figure 8. Waveforms
Switching time waveforms VN808-E
12/22 Doc ID 11455 Rev 8
Figure 8. Waveforms (continued)
VN808-E Reverse polarity protection
Doc ID 11455 Rev 8 13/22
6 Reverse polarity protection
This schematic can be used with any type of load.
The following is an indication on how to dimension the RGND resistor.
RGND = (-VCC) / (-IGND)
where -IGND is the DC reverse ground pin current and can be found in the absolute
maximum rating section of the device datasheet.
Power dissipation in RGND (when VCC< 0: during reverse polarity situations) is:
PD = (-VCC)2/RGND
Note: In normal condition (no reverse polarity) due to the diode there will be a voltage drop
between GND of the device and GND of the system.
Figure 9. Reverse polarity protection
Status
Inputi
GND
Outputi
+ Vcc
RGND
Load
Diode
Status
Inputi
GND
Outputi
+ Vcc
RGND
Load
Diode
Package mechanical data VN808-E
14/22 Doc ID 11455 Rev 8
7 Package mechanical data
In order to meet environmental requirements, ST offers these devices in different grades of
ECOPACK® packages, depending on their level of environmental compliance. ECOPACK®
specifications, grade definitions and product status are available at: www.st.com.
ECOPACK is an ST trademark.
Table 10. PowerSO-36 mechanical data
Dim.
mm inch
Min. Typ. Max. Min. Typ. Max.
A 3.60 0.1417
a1 0.10 0.30 0.003 0.0118
a2 3.30 0.1299
a3 0 0.10 0 0.0039
b 0.22 0.38 0.008 0.0150
c 0.23 0.32 0.009 0.0126
D (1) 15.80 16.00 0.622 0.6299
D1 9.40 9.80 0.370 0.3858
E 13.90 14.50 0.547 0.5709
E1 (1) 10.90 11.10 0.429 0.4370
E2 2.90 0.1142
E3 5.8 6.2 0.228 0.2441
e 0.65 0.025
e3 11.05 0.435
G 0 0.10 0.000 0.0039
H 15.50 15.90 0.610 0.6260
h 1.10 0.0433
L 0.80 1.10 0.031 0.0433
N 10° 10°
S 0°
VN808-E Package mechanical data
Doc ID 11455 Rev 8 15/22
Figure 10. PowerSO-36 drawings
Package mechanical data VN808-E
16/22 Doc ID 11455 Rev 8
7.1 Footprint recommended data
Figure 11. Footprint recommended data
Table 11. Footprint data
Dim. mm. inch
A 9.5 0.374
B 14.7-15.0 0.579-0.591
C 12.5-12.7 0.492-0.500
D 6.3 0.248
E 0.46 0.018
F 0.27 0.011
G 0.65 0.026
VN808-E Package mechanical data
Doc ID 11455 Rev 8 17/22
7.2 Tube shipment information
Figure 12. Tube shipment information
Base quantity 31 pcs.
Bulk quantity 310 pcs.
Table 12. Tube mechanical data
Dim. mm. inch
A 18.80 0.740
B 17.2 ±0.2 0.677 ±0.008
C 8.20 ±0.2 0.323 ±0.008
D 10.90 ±0.2 0.429 ±0.008
E 2.90 ±0.2 0.114 ±0.008
F 0.40 0.016
G 0.80 0.031
H 6.30 0.248
I 4.30 ±0.2 0.165 ±0.008
J 3.7 ±0.2 0.146 ±0.008
K 9.4 0.370
L 0.40 0.016
M 0.80 0.031
N 3.50 ±0.2 0.138 ±0.008
Package mechanical data VN808-E
18/22 Doc ID 11455 Rev 8
7.3 Tape and reel shipment information
Figure 13. Tape specifications
Base quantity 600 pcs.
Bulk quantity 600 pcs.
Table 13. Tape mechanical data
Dim. mm. inch
D 1.50 +0.1/0 0.059 +0.004/0
E 1.75 ±0.1 0.069 ±0.004
Po 4.00 ±0.1 0.157 ±0.004
T max. 0.40 0.016
D1 min. 1.50 0.059
F 11.5 ±0.05 0.453 ±0.002
K max. 6.50 0.256
P2 2.00 ±0.1 0.079 ±0.004
R 50 1.968
W 24.00 ±0.30 0.945 ±0.012
P1 24.00 0.945
Ao, Bo, Ko 0.05 min to 1.0 max. 0.002 min to 0.039 max.
,P
5
#P
%1
1P
&
8
'
"P 1
6TFSEJSFDUJPOPGGFFE
$
3
6TFSEJSFDUJPOPGGFFE
3
#FOEJOHSBEJVT
VN808-E Package mechanical data
Doc ID 11455 Rev 8 19/22
Figure 14. Reel specifications
Table 14. Reel mechanical data
Dim. mm. inch
Tape size 24.0 ±0.30 0.945 ±0.012
A max. 330.0 12.992
B min. 1.5 0.059
C 13.0 ±0.20 0.512 ±0.008
D min. 20.2 0.795
N min. 60 2.362
G 24.4 +2/-0 0.960 +0.079/-0
T max. 30.4 1.197
$
'
%
)XOOUDGLXV
7DSHVORWLQFRUHIRUWDSHVWDUW
PPLQPLQZLGWK
PPLQPLQ
DFFHVVKROH
DWVORWORFDWLRQ
&
1
*PHDVXUHG
DWKXE
7
Order codes VN808-E
20/22 Doc ID 11455 Rev 8
8 Order codes
Table 15. Order codes
Order codes Package Packaging
VN808-E PowerSO-36 Tube
VN808TR-E PowerSO-36 Tape and reel
VN808-E Revision history
Doc ID 11455 Rev 8 21/22
9 Revision history
Table 16. Document revision history
Date Revision Changes
13-Sep-2005 1 Initial release
1-Mar-2007 2 Document reformatted
12-Mar-2007 3 Typo in Figure 3.
26-Mar-2007 4 Typo note Table 2.
07-Jul-2008 5 Added: Section 6 on page 13
04-Aug-2008 6 Added: Figure 11: PowerSO-36 footprint on page 15
25-Aug-2009 7 Updated Section 6: Reverse polarity protection
24-Feb-2010 8 Updated Section 7: Package mechanical data
VN808-E
22/22 Doc ID 11455 Rev 8
Please Read Carefully:
Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the
right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any
time, without notice.
All ST products are sold pursuant to ST’s terms and conditions of sale.
Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no
liability whatsoever relating to the choice, selection or use of the ST products and services described herein.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this
document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products
or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such
third party products or services or any intellectual property contained therein.
UNLESS OTHERWISE SET FORTH IN ST’S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED
WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED
WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS
OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT.
UNLESS EXPRESSLY APPROVED IN WRITING BY AN AUTHORIZED ST REPRESENTATIVE, ST PRODUCTS ARE NOT
RECOMMENDED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING
APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY,
DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. ST PRODUCTS WHICH ARE NOT SPECIFIED AS "AUTOMOTIVE
GRADE" MAY ONLY BE USED IN AUTOMOTIVE APPLICATIONS AT USER’S OWN RISK.
Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void
any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any
liability of ST.
ST and the ST logo are trademarks or registered trademarks of ST in various countries.
Information in this document supersedes and replaces all information previously supplied.
The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners.
© 2010 STMicroelectronics - All rights reserved
STMicroelectronics group of companies
Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan -
Malaysia - Malta - Morocco - Philippines - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America
www.st.com