ICS83840 Integrated Circuit Systems, Inc. DDR SDRAM MUX GENERAL DESCRIPTION FEATURES The ICS83840 is a DDR SDRAM MUX and is a member of the HiPerClock STM family of High HiPerClockSTM Performance Clock Solutions from ICS. The device has 10 Host Lines and each host line can be passed to 4 Data Ports. The 10 channels are allocated as follows in the DDR SDRAM application: 8 data lines, 1 strobe line and 1 DQm line. The Host/Data Ports are compatible with single-ended SSTL-2 and the device operates from a 2.5V supply. * 40 low skew single-ended DIMM ports ICS * 4 SSTL-2 compatible enable inputs * Maximum Switching Speed: 3ns * Output skew: 120ps (maximum) * Bank skew: 45ps (maximum) * ron = 8 (typical) * Full 2.5V supply modes * 0C to 70C ambient operating temperature Guaranteed low output skew makes the ICS83840 ideal for demanding applications which require well defined performance and repeatability. * Pin compatible with the CBTV4010 SIMPLIFIED SCHEMATIC LOGIC DIAGRAM HP0 RON 0DP0 Sw 1DP0 Sw 2DP0 Sw HPx nDPx Sw 3DP0 400 HP9 RON 0DP9 Sw 1DP9 Sw nSn 2DP9 Sw Sw 3DP9 nS0 SW nS1 nS2 nS3 PIN ASSIGNMENT 1 2 3 A VDD nS1 nc B nS2 VDD nS0 C nc nS3 GND 3DP2 D 4 GND 5 6 7 1DP0 2DP0 3DP0 0DP0 HP0 0DP1 8 1DP1 9 10 11 2DP1 3DP1 0DP2 HP1 GND 1DP2 HP2 2DP2 E 2DP9 3DP9 0DP3 1DP3 F 1DP9 HP9 HP 3 2DP3 G H 0DP9 3DP8 GND 3DP3 2DP8 0DP4 J 1DP8 HP8 K L 0DP8 GND HP7 3DP7 2DP7 1DP7 83840AH 0DP7 3DP6 HP6 GND 2DP6 1DP6 0DP6 3DP5 HP4 1DP4 HP5 3DP4 2DP4 2DP5 1DP5 0DP5 www.icst.com/products/hiperclocks.html 1 ICS83840 64-Ball TFBGA 7mm x 7mm x 1.2mm package body H Package Top View REV. A DECEMBER 22, 2003 ICS83840 Integrated Circuit Systems, Inc. DDR SDRAM MUX TABLE 1. PIN DESCRIPTIONS Number Name Type Description A1, B2 VDD Power Positive supply pins. B4, B10, D2, G10, K2, K7 GND Power Power supply ground. A 3, C 1 nc Unused No connect. A2, B1, C2, B3 B6, B9, C10, F2, F10, J2, J10, K3, K6, K9 A5, A6, A7, B5 nS1, nS2, nS3, nS0 HP0, HP1, HP2, HP9, HP3, HP8, HP4, HP7, HP6, HP5 1DP0, 2DP0, 3DP0, 0DP0 Por t Select pins. Por t Host por ts. Por t DIMM por ts. A9, A10, B7, B8 2DP1, 3DP1, 0DP1, 1DP1 Por t DIMM por ts. A11, B11, C11, D10 0DP2, 1DP2, 2DP2, 3DP2 Por t DIMM por ts. E10, E11, F11, G11 ODP3, 1DP3, 2DP3, 3DP3 Por t DIMM por ts. H10, J11, K10, K11 0DP4, 1DP4, 3DP4, 2DP4 Por t DIMM por ts. K8, L9, L10, L11 3DP5, 2DP5, 1DP5, 0DP5 Por t DIMM por ts. K5, L5, L6, L7 3DP6, 2DP6, 1DP6, 0DP6 Por t DIMM por ts. K4, L1, L2, L3 0DP7, 3DP7, 2DP7, 1DP7 Por t DIMM por ts. G2, H2, J1, K1 3DP8, 2DP8, 1DP8, 0DP8 Por t DIMM por ts. E1, E2, F1, G1 2DP9, 3DP9, 1DP9, 0DP9 Por t DIMM por ts. TABLE 2. PIN CHARACTERISTICS Symbol Parameter Test Conditions Minimum Typical Maximum Units CIN Input Capacitance nSx VI = 0V or VDD 5 pF CON Channel on Capacitance HP x VIN = 1.5V 12 pF NOTE: Capacitance values are measured at 10MHz and a bias voltage 3V. Capacitance is not production tested. TABLE 3. FUNCTION TABLE Control Input nSx L H 83840AH Function Host Por t = DIMM Por t Host Por t = Disconnected DIMM Por t = 400 to GND www.icst.com/products/hiperclocks.html 2 REV. A DECEMBER 22, 2003 ICS83840 Integrated Circuit Systems, Inc. DDR SDRAM MUX ABSOLUTE MAXIMUM RATINGS Supply Voltage, VDD -0.5V to +3.3V NOTE: Stresses beyond those listed under Absolute Inputs, VI -0.3V to VDD + 0.3 V Maximum Ratings may cause permanent damage to the device. These ratings are stress specifications only. Functional Ports operation of product at these conditions or any conditions be- DC Input Clamp Current, IIK -50mA Package Thermal Impedance, JA 50.04C/W (0 mfps) istics is not implied. Exposure to absolute maximum rating -65C to 150C conditions for extended periods may affect product reliability. Storage Temperature, TSTG yond those listed in the DC Characteristics or AC Character- TABLE 4A. POWER SUPPLY DC CHARACTERISTICS, VDD = 2.5V 0.2V, TA = 0C TO 70C Symbol Parameter Test Conditions VDD Positive Supply Voltage IDD Power Supply Current Minimum Typical Maximum Units 2.3 2.5 2.7 V 50 A Maximum Units TABLE 4B. DC CHARACTERISTICS, VDD = 2.5V 0.2V, TA = 0C TO 70C Symbol Parameter Test Conditions VIH Input High Voltage nSx VIL Input Low Voltage nSx VIK Input Clamp Voltage IL Input Leakage Current nSx Host Por t DIMM Por t rON On Resistance; NOTE 1 Minimum Typical 1.6 V 0.9 V VDD = 2.3V; II = -18mA -1.2 V VDD = 2.5V; VI = VDD or GND; nS = VDD 100 A 100 A nS = GND for IIL(test) 100 A 13 VDD = 2.5V; VA = 0.8V; VB = 1.0V 5 8 5 8 13 VDD = 2.5V; VA = 1.7V; VB = 1.5V NOTE 1: Measured by the current between the Host and the DIMM terminals at the indicated voltages on each side of the switch. TABLE 5. AC CHARACTERISTICS, VDD = 2.5V 0.2V, TA = 0C TO 70C Symbol Parameter Test Conditions Minimum Typical Maximum Units Propagation Delay; From HPx or xDPx to tPD 85 150 220 ps NOTE 1, 4 xDPx or HPx Output From nSx to 1.7 ns t EN Enable Time HPx or nDPx Output From nSx to tDIS 1.6 ns Disable Time HPx or nDPx Output Skew; Any Por t to any Por t 120 ps tOSK NOTE 2, 4 Bank Skew; Any Por t to any Por t 45 ps tBSK NOTE 3, 4 within the same bank NOTE 1: Measured from VDD/2 of the input to VDD/2 of the output. NOTE 2: Defined as skew between outputs at the same supply voltage and with equal load conditions. Measured at VDDO/2. NOTE 3: Defined as skew within a bank with equal load conditions. NOTE 4: Not production tested, guaranteed by characterization. 83840AH www.icst.com/products/hiperclocks.html 3 REV. A DECEMBER 22, 2003 ICS83840 Integrated Circuit Systems, Inc. DDR SDRAM MUX PARAMETER MEASUREMENT INFORMATION VDD = 1.25V 0.1V V SCOPE V DD DD nDPx 2 Qx LVCMOS V DD nDPy GND 2 t sk(o) -1.25V 0.1V This circuit is used for test purposes only, not intended for application use. 2.5V OUTPUT LOAD AC TEST CIRCUIT OUTPUT SKEW Sn (Low-level enabling) VDD 2 XDP0:XDP9 2.5V 1.25V 1.25V 0V VDD 2 XDP0:XDP9 tPZH t sk(o) Output nDPx (See Note) tPHZ VOH VOH - 0.15V 1.25V VOL NOTE: The output is high except when disabled by the Sn control. BANK SKEW (where X denotes outputs in the same bank) 3-STATE OUTPUT ENABLE/DISABLE TIMES VDD 2 D or H VDD 2 H or D t PD PROPAGATION DELAY 83840AH www.icst.com/products/hiperclocks.html 4 REV. A DECEMBER 22, 2003 ICS83840 Integrated Circuit Systems, Inc. DDR SDRAM MUX RELIABILITY INFORMATION TABLE 6. JAVS. AIR FLOW TABLE JA by Velocity (Millimeter Feet per Second) Two-Layer PCB, JEDEC Standard Test Boards 0 1 2 50.04C/W 43.18C/W 41.17C/W NOTE: Most modern PCB designs use multi-layered boards. The data in the second row pertains to most designs. TRANSISTOR COUNT The transistor count for ICS83840 is: 320 83840AH www.icst.com/products/hiperclocks.html 5 REV. A DECEMBER 22, 2003 ICS83840 Integrated Circuit Systems, Inc. DDR SDRAM MUX PACKAGE OUTLINE - H SUFFIX TABLE 7. PACKAGE DIMENSIONS JEDEC VARIATION ALL DIMENSIONS IN MILLIMETERS FBGA SYMBOL MINIMUM NOMINAL MAXIMUM 64 Balls, 7x7mm, 11x11 Pattern A 1.0 1.1 1.2 A1 0.165 0.2 0.235 A2 0.16 0.2 0.24 A3 0.675 0.7 0.725 b 0.25 0.3 0.35 D 7.00 BSC D1 5.00 BSC E 7.00 BSC E1 5.00 BSC e 0.50 BSC REFERENCE DOCUMENT: JEDEC PUBLICATION 95 83840AH www.icst.com/products/hiperclocks.html 6 REV. A DECEMBER 22, 2003 ICS83840 Integrated Circuit Systems, Inc. DDR SDRAM MUX TABLE 8. ORDERING INFORMATION Part/Order Number Marking Package Count Temperature ICS83840AH ICS83840AH 64-Ball TFBGA 416 per tray 0C to 70C ICS83840AHT ICS83840AH 64-Ball TFBGA on Tape and Reel 1000 0C to 70C ICS83840AHLF ICS3840ALF 64-Ball, Lead Free, TFBGA 416 per tray 0C to 70C ICS83840AHLFT ICS3840ALF 64-Ball, Lead Free, TFBGA on Tape and Reel 1000 0C to 70C While the information presented herein has been checked for both accuracy and reliability, Integrated Circuit Systems, Incorporated (ICS) assumes no responsibility for either its use or for infringement of any patents or other rights of third parties, which would result from its use. No other circuits, patents, or licenses are implied. This product is intended for use in normal commercial applications. Any other applications such as those requiring extended temperature range, high reliability, or other extraordinary environmental requirements are not recommended without additional processing by ICS. ICS reserves the right to change any circuitry or specifications without notice. ICS does not authorize or warrant any ICS product for use in life support devices or critical medical instruments. 83840AH www.icst.com/products/hiperclocks.html 7 REV. A DECEMBER 22, 2003 ICS83840 Integrated Circuit Systems, Inc. DDR SDRAM MUX REVISION HISTORY SHEET Rev A 83840AH Table Page 1 6 7 Description of Change Changed dimension on Pin Assignment from 0.7mm to 1.2mm. Updated Package Outline Drawing and Package Dimensions Table. Added "Lead Free" marking. www.icst.com/products/hiperclocks.html 8 Date 12/22/03 REV. A DECEMBER 22, 2003