DS2151 - Dallas Semiconductor

1 of 51 081099

FEATURES

§ Complete DS1/ISDN-PRI transceiver

functionality

§ Line interface can handle both long- and

short-haul trunks

§ 32-bit or 128-bit jitter attenuator

§ Generates DSX-1 and CSU line build outs

§ Frames to D4, ESF, and SLC-96R formats

§ Dual onboard two-frame elastic store slip

buffers that connect to backplanes up to 8.192

MHz

§ 8-bit parallel control port that can be used on

either multiplexed or non-multiplexed buses

§ Extracts and inserts Robbed-Bit signaling

§ Detects and generates yellow and blue alarms

§ Programmable output clocks for Fractional T1

§ Fully independent transmit and receive

functionality

§ Onboard FDL support circuitry

§ Generates and detects CSU loop codes

§ Contains ANSI one’s density monitor and

enforcer

§ Large path and line error counters including

BPV, CV, CRC6, and framing bit errors

§ Pin compatible with DS2153Q E1 Single-

Chip Transceiver

§ 5V supply; low power CMOS

§ Industrial grade version (-40°C to +85°C)

available (DS2151QN)

PIN ASSIGNMENT

DESCRIPTION

The DS2151Q T1 Single-Chip Transceiver (SCT) contains all of the necessary functions for connection

to T1 lines whether they be DS-1 long haul or DSX-1 short haul. The clock recovery circuitry

automatically adjusts to T1 lines from 0 feet to over 6000 feet in length. The device can generate both

DSX-1 line build outs as well as CSU build outs of -7.5 dB, -15 dB, and -22.5 dB. The onboard jitter

attenuator (selectable to either 32 bits or 128 bits) can be placed in either the transmit or receive data

paths. The framer locates the frame and multiframe boundaries and monitors the data stream for alarms.

It is also used for extracting and inserting Robbed-Bit signaling data and FDL data. The device contains

a set of 64 8-bit internal registers which the user can access to control the operation of the unit. Quick

access via the parallel control port allows a single micro to handle many T1 lines. The device fully meets

all of the latest T1 specifications including ANSI T1.403-199X, AT&T TR 62411 (12-90), and ITU

G.703, G.704, G.706, G.823, and I.431.

DS2151Q

T1 Single-Chip Transceiver

www.dalsemi.com

Dallas

DS2151Q

T1SCT

ELASTIC

STORES

FRAMER

LONG & SHORT

HAUL LINE

INTERFACE

PARALLEL CONTROL

PORT

ALE

RLINK

RLCLK

DVSS

RCLK

RCHCLK

RSER

RSYNC

RLOS/LOTC

SYSCLK

TSER

TCLK

DVDD

TSYNC

TLINK

TLCLK

TCHBLK

TRING

TVDD

TVSS

TTIP

RCHBLK

ACLKI

BTS

RTIP

RRING

RVDD

RVSS

XTAL1

XTAL2

INT1

INT2

AD7

AD6

AD5

AD4

AD3

AD2

AD1

AD0

TCHCLK

ACTUAL SIZE OF 44-PIN PLCC

FUNCTIONAL BLOCKS

DS2151Q

2 of 51

TABLE OF CONTENTS

1. Introduction

2. Parallel Control Port

3. Control Registers

4. Status and Information Registers

5. Error Count Registers

6. FDL/Fs Extraction/Insertion

7. Signaling Operation

8. Transmit Transparency and Idle Registers

9. Clock Blocking Registers

10. Elastic Stores Operation

11. Receive Mark Registers

12. Line Interface Functions

13. Timing Diagrams and Transmit Flow Diagram

14. DC and AC Characteristics

1.0 INTRODUCTION

The analog AMI waveform off of the T1 line is transformer coupled into the RRING and RTIP pins of

the DS2151Q. The device recovers clock and data from the analog signal and passes it through the jitter

attenuation mux to the receive side framer where the digital serial stream is analyzed to locate the framing

pattern. If needed, the receive side elastic store can be enabled in order to absorb the phase and frequency

differences between the recovered T1 data stream and an asynchronous backplane clock which is

provided at the SYSCLK input.

The transmit side of the DS2151Q is totally independent from the receive side in both the clock

requirements and characteristics. Data can be either provided directly to the transmit formatter or via an

elastic store. The transmit formatter will provide the necessary data overhead for T1 transmission. Once

the data stream has been prepared for transmission, it is sent via the jitter attenuation mux to the

waveshaping and line driver functions. The DS2151Q will drive the T1 line from the TTIP and TRING

pins via a coupling transformer.

DS2151Q

3 of 51

DS2151Q BLOCK DIAGRAM Figure 1-1

DS2151Q

4 of 51

PIN DESCRIPTION Table 1-1

PIN SYMBOL TYPE DESCRIPTION

AD4

AD5

AD6

AD7

I/O Address/Data Bus. An 8-bit multiplexed address/data bus.

(DS) IRead Input (Data Strobe).

6CS IChip Select. Must be low to read or write the port.

7ALE(AS) IAddress Latch Enable (Address Strobe). A positive going edge

serves to demultiplex the bus.

8WR (R/W)IWrite Input (Read/Write).

9RLINK OReceive Link Data. Updated with either FDL data (ESF) or Fs bits

(D4) or Z bits (ZBTSI) one RCLK before the start of a frame. See

Section 13 for timing details.

10 RLCLK OReceive Link Clock. 4 kHz or 2 kHz (ZBTSI) demand clock for the

RLINK output. See Section 13 for timing details.

11 DVSS -Digital Signal Ground. 0.0 volts. Should be tied to local ground plane.

12 RCLK OReceive Clock. Recovered 1.544 MHz clock.

13 RCHCLK OReceive Channel Clock. 192 kHz clock which pulses high during the

LSB of each channel. Useful for parallel to serial conversion of channel

data, locating Robbed-Bit signaling bits, and for blocking clocks in

DDS applications. See Section 13 for timing details.

14 RSER OReceive Serial Data. Received NRZ serial data, updated on rising

edges of RCLK or SYSCLK.

15 RSYNC I/O Receive Sync. An extracted pulse, one RCLK wide, is output at this

pin which identifies either frame (RCR2.4=0) or multiframe boundaries

(RCR2.4=1). If set to output frame boundaries, then via RCR2.5,

RSYNC can also be set to output double-wide pulses on signaling

frames. If the elastic store is enabled via the CCR1.2, then this pin can

be enabled to be an input via RCR2.3 at which a frame boundary pulse

is applied. See Section 13 for timing details.

16 RLOS/LOTC OReceive Loss of Sync/Loss of Transmit Clock. A dual function

output. If CCR3.5=0, will toggle high when the synchronizer is

searching for the T1 frame and multiframe; if CCR3.5=1, will toggle

high if the TCLK pin has not toggled for 5 us.

17 SYSCLK ISystem Clock. 1.544 MHz or 2.048 MHz clock. Only used when the

elastic store functions are enabled via either CCR1.7 or CCR1.2.

Should be tied low in applications that do not use the elastic store. If

tied high for more than 100 us, will force all output pins (including the

parallel port) to 3-state.

18 RCHBLK OReceive Channel Block. A user programmable output that can be

forced high or low during any of the 24 T1 channels. Useful for

blocking clocks to a serial UART or LAPD controller in applications

where not all T1 channels are used such as Fractional T1, 384k bps

service, 768k bps, or ISDN-PRI. Also useful for locating individual

channels in drop-and-insert applications. See Section 13 for timing

details.

DS2151Q

5 of 51

PIN SYMBOL TYPE DESCRIPTION

19 ACLKI IAlternate Clock Input. Upon a receive carrier loss, the clock applied at

this pin (normally 1.544 MHz) will be routed to the RCLK pin. If no

clock is routed to this pin, then it should be tied to DVSS VIA A1K Ohm

RESISTOR.

20 BTS IBus Type Select. Strap high to select Motorola bus timing; strap low to

select Intel bus timing. This pin controls the function of the

(DS),

ALE(AS), and WR (R/W) pins. If BTS=1, then these pins assume the

function listed in parenthesis ().

22 RTIP

RRING -Receive Tip and Ring. Analog inputs for clock recovery circuitry;

connects to a 1:1 transformer (see Section 12 for details).

23 RVDD -Receive Analog Positive Supply. 5.0 volts. Should be tied to DVDD

and TVDD pins.

24 RVSS -Receive Signal Ground. 0.0 volts. Should be tied to local ground plane

26 XTAL1

XTAL2 -Crystal Connections. A pullable 6.176 MHz crystal must be applied to

these pins. See Section 12 for crystal specifications.

27 INT1 OReceive Alarm Interrupt 1. Flags host controller during alarm

conditions defined in Status Register 1. Active low, open drain output.

28 INT2 OReceive Alarm Interrupt 2. Flags host controller during conditions

defined in Status Register 2. Active low, open drain output.

29 TTIP -Transmit Tip. Analog line driver output; connects to a step-up

transformer (see Section 12 for details).

30 TVSS -Transmit Signal Ground. 0.0 volts. Should be tied to local ground

plane.

31 TVDD -Transmit Analog Positive Supply. 5.0 volts. Should be tied to DVDD

and RVDD pins.

32 TRING -Transmit Ring. Analog line driver outputs; connects to a step-up

transformer (see Section 12 for details).

33 TCHBLK OTransmit Channel Block. A user programmable output that can be

forced high or low during any of the 24 T1 channels. Useful for blocking

clocks to a serial UART or LAPD controller in applications where not all

T1 channels are used such as Fractional T1, 384k bps service, 768k bps,

or ISDN-PRI. Also useful for locating individual channels in drop-and-

insert applications. See Section 13 for timing details.

34 TLCLK OTransmit Link Clock. 4 kHz or 2 kHz (ZBTSI) demand clock for the

TLINK input. See Section 13 for timing details.

35 TLINK ITransmit Link Data. If enabled via TCR1.2, this pin will be sampled

during the F-bit time on the falling edge of TCLK for data insertion into

either the FDL stream (ESF) or the Fs bit position (D4) or the Z-bit

position (ZBTSI). See Section 13 for timing details.

36 TSYNC I/O Transmit Sync. A pulse at this pin will establish either frame or

multiframe boundaries for the DS2151Q. Via TCR2.2, the DS2151Q can

be programmed to output either a frame or multiframe pulse at this pin. If

this pin is set to output pulses at frame boundaries, it can also be set via

TCR2.4 to output double-wide pulses at signaling frames. See Section 13

for timing details.

37 DVDD -Digital Positive Supply. 5.0 volts. Should be tied to RVDD and TVDD

pins.

DS2151Q

6 of 51

PIN SYMBOL TYPE DESCRIPTION

38 TCLK ITransmit Clock. 1.544 MHz primary clock.

39 TSER ITransmit Serial Data. Transmit NRZ serial data, sampled on the falling edge

of TCLK.

40 TCHCLK OTransmit Channel Clock. 192 kHz clock which pulses high during the LSB

of each channel. Useful for parallel to serial conversion of channel data,

locating Robbed-Bit signaling bits, and for blocking clocks in DDS applica-

tions. See Section 13 for timing details.

AD0

AD1

AD2

AD3

I/O Address/Data Bus. An 8-bit multiplexed address/data bus.

DS2151Q REGISTER MAP

ADDRESS R/W REGISTER NAME ADDRESS R/W REGISTER NAME

20 R/W Status Register 1. 30 R/W Common Control Register 3.

21 R/W Status Register 2. 31 R/W Receive Information Register 2.

22 R/W Receive Information Register 1. 32 R/W Transmit Channel Blocking Register 1.

23 RLine code Violation Count

24 RLine code Violation Count

25 RPath Code Violation Count

26 RPath Code Violation Count

27 RMultiframe Out of Sync Count

28 RReceive FDL Register. 38 R/W Common Control Register 2.

29 R/W Receive FDL Match Register 1. 39 R/W Transmit Transparency Register 1.

2A R/W Receive FDL Match Register 2. 3A R/W Transmit Transparency Register 2.

2B R/W Receive Control Register 1. 3B R/W Transmit Transparency Register 3.

2C R/W Receive Control Register 2. 3C R/W Transmit Idle Register 1.

2D R/W Receive Mark Register 1. 3D R/W Transmit Idle Register 2.

2E R/W Receive Mark Register 2. 3E R/W Transmit Idle Register 3.

2F R/W Receive Mark Register 3. 3F R/W Transmit Idle Definition Register.

60 RReceive Signaling Register 1. 70 R/W Transmit Signaling Register 1.

61 RReceive Signaling Register 2. 71 R/W Transmit Signaling Register 2.

62 RReceive Signaling Register 3. 72 R/W Transmit Signaling Register 3.

DS2151Q

7 of 51

DS2151Q REGISTER MAP (continued)

63 RReceive Signaling Register 4. 73 R/W Transmit Signaling Register 4.

64 RReceive Signaling Register 5. 74 R/W Transmit Signaling Register 5.

65 RReceive Signaling Register 6. 75 R/W Transmit Signaling Register 6.

66 RReceive Signaling Register 7. 76 R/W Transmit Signaling Register 7.

67 RReceive Signaling Register 8. 77 R/W Transmit Signaling Register 8.

68 RReceive Signaling Register 9. 78 R/W Transmit Signaling Register 9.

69 RReceive Signaling Register 10. 79 R/W Transmit Signaling Register 10.

6A RReceive Signaling Register 11. 7A R/W Transmit Signaling Register 11.

6B RReceive Signaling Register 12. 7B R/W Transmit Signaling Register 12.

6C R/W Receive Channel Blocking

6D R/W Receive Channel Blocking

6E R/W Receive Channel Blocking

6F R/W Interrupt Mask Register 2. 7F R/W Interrupt Mask Register 1.

NOTES:

1. Address 25 also contains Multiframe Out of Sync Count Register 1.

2. The Test Register is used only by the factory; this register must be cleared (set to all 0s) on power-up

initialization to insure proper operation.

2.0 PARALLEL PORT

The DS2151Q is controlled via a multiplexed bidirectional address/data bus by an external

microcontroller or microprocessor. The DS2151Q can operate with either Intel or Motorola bus timing

configurations. If the BTS pin is tied low, Intel timing will be selected; if tied high, Motorola timing will

be selected. All Motorola bus signals are listed in parenthesis (). See the timing diagrams in the A.C.

Electrical Characteristics for more details. The multiplexed bus on the DS2151Q saves pins because the

address information and data information share the same signal paths. The addresses are presented to the

pins in the first portion of the bus cycle and data will be transferred on the pins during second portion of

the bus cycle. Addresses must be valid prior to the falling edge of ALE (AS), at which time the

DS2151Q

8 of 51

DS2151Q latches the address from the AD0 to AD7 pins. Valid write data must be present and held

stable during the later portion of the DS or WR pulses. In a read cycle, the DS2151Q outputs a byte of

data during the latter portion of the DS or

pulses. The read cycle is terminated and the bus returns to

a high impedance state as

transitions high in Intel timing or as DS transitions low in Motorola timing.

The DS2151Q can also be easily connected to non-multiplexed buses. Please see the separate Application

Note for a detailed discussion of this topic.

3.0 CONTROL REGISTERS

The operation of the DS2151Q is configured via a set of eight registers. Typically, the control registers

are only accessed when the system is first powered up. Once the DS2151Q has been initialized, the

control registers will only need to be accessed when there is a change in the system configuration. There

are two Receive Control Registers (RCR1 and RCR2), two Transmit Control Registers (TCR1 and

TCR2), a Line Interface Control Register (LICR), and three Common Control Registers (CCR1, CCR2,

and CCR3). Seven of the eight registers are described below. The LICR is described in Section 12.

RCR1: RECEIVE CONTROL REGISTER 1 (Address=2B Hex)

(MSB) (LSB)

LCVCRF ARC OOF1 OOF2 SYNCC SYNCT SYNCE RESYNC

SYMBOL POSITION NAME AND DESCRIPTION

LCVCRF RCR1.7 Line Code Violation Count Register Function Select.

0=do not count excessive 0s

1=count excessive 0s

ARC RCR1.6 Auto Resync Criteria.

0=Resync on OOF or RCL event

1=Resync on OOF only

OOF1 RCR1.5 Out Of Frame Select 1.

0=2/4 frame bits in error

1=2/5 frame bits in error

OOF2 RCR1.4 Out Of Frame Select 2.

0=follow RCR1.5

1=2/6 frame bits in error

SYNCC RCR1.3 Sync Criteria.

In D4 Framing Mode

0=search for Ft pattern, then search for Fs pattern

1=cross couple Ft and Fs pattern

In ESF Framing Mode

0=search for FPS pattern only

1=search for FPS and verify with CRC6

SYNCT RCR1.2 Sync Time.

0=qualify 10 bits

1=qualify 24 bits

DS2151Q

9 of 51

SYNCE RCR1.1 Sync Enable.

0=auto resync enabled

1=auto resync disabled

RESYNC RCR1.0

Resync

. When toggled from low to high, a resynchronization

of the receive side framer is initiated. Must be cleared and set

again for a subsequent resync.

RCR2: RECEIVE CONTROL REGISTER 2 (Address=2C Hex)

(MSB) (LSB)

RCS RZBTSI RSDW RSM RSIO RD4YM FSBE MOSCRF

SYMBOL POSITION NAME AND DESCRIPTION

RCS RCR2.7 Receive Code Select.

0=idle code (7F Hex)

1=digital milliwatt code (1E/0B/0B/1E/9E/8B/8B/9E Hex)

RZBTSI RCR2.6 Receive Side ZBTSI Enable.

0=ZBTSI disabled

1=ZBTSI enabled

RSDW RCR2.5 RSYNC Double-Wide.

0=do not pulse double-wide in signaling frames

1=do pulse double-wide in signaling frames (note: this bit must

be set to 0 when RCR2.4=1 or when RCR2.3=1)

RSM RCR2.4 RSYNC Mode Select.

0=frame mode (see the timing in Section 13)

1=multiframe mode (see the timing in Section 13)

RSIO RCR2.3 RSYNC I/O Select.

0=RSYNC is an output

1=RSYNC is an input (only valid if elastic store enabled) (note:

this bit must be set to 0 when CCR1.2=0)

RD4YM RCR2.2 Receive Side D4 Yellow Alarm Select.

0=0s in bit 2 of all channels

1=a 1 in the S-bit position of frame 12

FSBE RCR2.1 PCVCR Fs Bit Error Report Enable.

0=do not report bit errors in Fs bit position; only Ft bit position

1=report bit errors in Fs bit position as well as Ft bit position

MOSCRF RCR2.0 Multiframe Out of Sync Count Register Function Select.

0=count errors in the framing bit position

1=count the number of multiframes out of sync

TCR1: TRANSMIT CONTROL REGISTER 1 (Address=35 Hex)

(MSB) (LSB)

LOTCMC TFPT TCPT RBSE GB7S TLINK TBL TYEL

SYMBOL POSITION NAME AND DESCRIPTION

DS2151Q

10 of 51

LOTCMC TCR1.7

Loss Of Transmit Clock Mux Control

. Determines whether

the transmit side formatter should switch to the ever present

RCLK if the TCLK input should fail to transition (see Figure 1-

1 for more details).

0=do not switch to RCLK if TCLK stops

1=switch to RCLK if TCLK stops

TFPT TCR1.6 Transmit Framing Pass Through. (see note below)

0=Ft or FPS bits sourced internally

1=Ft or FPS bits sampled at TSER during F-bit time

TCPT TCR1.5 Transmit CRC Pass Through. (see note below)

0=source CRC6 bits internally

1=CRC6 bits sampled at TSER during F-bit time

RBSE TCR1.4 Robbed-Bit Signaling Enable. (see note below)

0=no signaling is inserted in any channel

1=signaling is inserted in all channels (the TTR registers can be

used to block insertion on a channel by channel basis)

GB7S TCR1.3 Global Bit 7 Stuffing. (see note below)

0=allow the TTR registers to determine which channels

containing all 0s are to be Bit 7 stuffed

1=force Bit 7 stuffing in all 0 byte channels regardless of how

the TTR registers are programmed

TLINK TCR1.2 TLINK Select. (see note below)

0=source FDL or Fs bits from TFDL register

1=source FDL or Fs bits from the TLINK pin

TBL TCR1.1 Transmit Blue Alarm. (see note below)

0=transmit data normally

1=transmit an unframed all 1s code at TPOS and TNEG

TYEL TCR1.0 Transmit Yellow Alarm. (see note below)

0=do not transmit yellow alarm

1=transmit yellow alarm

Note: for a detailed description of how the bits in TCR1 affect the transmit side formatter of the

DS2151Q, please see Figure 13-9.

DS2151Q

11 of 51

TCR2: TRANSMIT CONTROL REGISTER 2 (Address=36 Hex)

(MSB) (LSB)

TEST1 TEST0 TZBTSI TSDW TSM TSIO TD4YM B7ZS

SYMBOL POSITION NAME AND DESCRIPTION

TEST1 TCR2.7 Test Mode Bit 1 for Output Pins. See Table 3-1.

TEST0 TCR2.6 Test Mode Bit 0 for Output Pins. See Table 3-1.

TZBTSI TCR2.5 Transmit Side ZBTSI Enable.

0=ZBTSI disabled

1=ZBTSI enabled

TSDW TCR2.4

TSYNC Double-Wide.

(note: this bit must be set to 0 when

TCR2.3=1 or when TCR2.2=0)

0=do not pulse double-wide in signaling frames

1=do pulse double-wide in signaling frames

TSM TCR2.3 TSYNC Mode Select.

0=frame mode (see the timing in Section 13)

1=multiframe mode (see the timing in Section 13)

TSIO TCR2.2 TSYNC I/O Select.

0=TSYNC is an input

1=TSYNC is an output

TD4YM TCR2.1 Transmit Side D4 Yellow Alarm Select.

0=0s in bit 2 of all channels

1=a 1 in the S-bit position of frame 12

B7ZS XTCR2.0 Bit 7 0 Suppression Enable.

0=no stuffing occurs

1=Bit 7 force to a 1 in channels with all 0s

OUTPUT PIN TEST MODES Table 3-1

TEST1 TEST0 EFFECT ON OUTPUT PINS

0 0 operate normally

0 1 force all output pins 3-state (including all I/O pins and parallel port pins)

1 0 force all output pins low (including all I/O pins except parallel port pins)

1 1 force all output pins high (including all I/O pins except parallel port pins)

DS2151Q

12 of 51

CCR1: COMMON CONTROL REGISTER 1 (Address=37 Hex)

(MSB) (LSB)

TESE LLB RSAO RLB SCLKM RESE PLB FLB

SYMBOL POSITION NAME AND DESCRIPTION

TESE CCR1.7 Transmit Elastic Store Enable.

0=elastic store is bypassed

1=elastic store is enabled

LLB CCR1.6 Local Loopback.

0=loopback disabled

1=loopback enabled

RSAO CCR1.5 Receive Signaling All 1s.

0=allow robbed signaling bits to appear at RSER

1=force all robbed signaling bits at RSER to 1

RLB CCR1.4 Remote Loopback.

0=loopback disabled

1=loopback enabled

SCLKM CCR1.3 SYSCLK Mode Select.

0=if SYSCLK is 1.544 MHz

1=if SYSCLK is 2.048 MHz

RESE CCR1.2 Receive Elastic Store Enable.

0=elastic store is bypassed

1=elastic store is enabled

PLB CCR1.1 Payload Loopback.

0=loopback disabled

1=loopback enabled

FLB CCR1.0 Framer Loopback.

0=loopback disabled

1=loopback enabled

LOCAL LOOPBACK

When CCR1.6 is set to a 1, the DS2151Q will be forced into Local LoopBack (LLB). In this loopback,

data will continue to be transmitted as normal through the transmit side of the SCT. Data being received

at RTIP and RRING will be replaced with the data being transmitted. Data in this loopback will pass

through the jitter attenuator and the jitter attenuator should be programmed to be in the transmit path.

LLB is primarily used in debug and test applications. Please see the DS2151Q Block Diagram in Section

1 for more details.

REMOTE LOOPBACK

When CCR1.4 is set to a 1, the DS2151Q will be forced into Remote LoopBack (RLB). In this loopback,

data recovered off the T1 line from the RTIP and RRING pins will be transmitted back onto the T1 line

DS2151Q

13 of 51

(with any BPVs that might have occurred intact) via the TTIP and TRING pins. Data will continue to

pass through the receive side of the DS2151Q as it would normally and the data at the TSER input will be

ignored. Data in this loopback will pass through the jitter attenuator. RLB is used to place the DS2151Q

into “line” loopback which is a requirement of both ANSI T1.403 and AT&T TR62411. Please see the

DS2151Q Block Diagram in Section 1 for more details.

PAYLOAD LOOPBACK

When CCR1.1 is set to a 1, the DS2151Q will be forced into Payload LoopBack (PLB). Normally, this

loopback is only enabled when ESF framing is being performed. In a PLB situation, the DS2151Q will

loop the 192 bits of payload data (with BPVs corrected) from the receive section back to the transmit

section. The FPS framing pattern, CRC6 calculation, and the FDL bits are not looped back, they are

reinserted by the DS2151Q. When PLB is enabled, the following will occur:

1. Data will be transmitted from the TTIP and TRING pins synchronous with RCLK instead of TCLK.

2. All of the receive side signals will continue to operate normally.

3. The TCHCLK and TCHBLK signals are forced low.

4. Data at the TSER pin is ignored.

5. The TLCLK signal will become synchronous with RCLK instead of TCLK.

FRAMER LOOPBACK

When CCR1.0 is set to a 1, the DS2151Q will enter a Framer LoopBack (FLB) mode. This loopback is

useful in testing and debugging applications. In FLB, the DS2151Q will loop data from the transmit side

back to the receive side. When FLB is enabled, the following will occur:

1. Unless the RLB is active, an unframed all 1s code will be transmitted at TTIP and TRING.

2. Data off the T1 line at RTIP and RRING will be ignored.

3. The RCLK output will be replaced with the TCLK input.

DS2151Q

14 of 51

CCR2: COMMON CONTROL REGISTER 2 (Address=38 Hex)

(MSB) (LSB)

TFM TB8ZS TSLC96 TFDL RFM RB8ZS RSLC96 RFDL

SYMBOL POSITION NAME AND DESCRIPTION

TFM CCR2.7 Transmit Frame Mode Select.

0=D4 framing mode

1=ESF framing mode

TB8ZS CCR2.6 Transmit B8ZS Enable.

0=B8ZS disabled

1=B8ZS enabled

TSLC96 CCR2.5 Transmit SLC-96/Fs Bit Loading Enable.

0=SLC-96/Fs bit Loading disabled

1=SLC-96/Fs bit Loading enabled

TFDL CCR2.4 Transmit FDL 0 Stuffer Enable.

0=0 stuffer disabled

1=0 stuffer enabled

RFM CCR2.3 Receive Frame Mode Select.

0=D4 framing mode

1=ESF framing mode

RB8ZS CCR2.2 Receive B8ZS Enable.

0=B8ZS disabled

1=B8ZS enabled

RSLC96 CCR2.1 Receive SLC-96 Enable.

0=SLC-96 disabled

1=SLC-96 enabled

RFDL CCR2.0 Receive FDL 0 Destuffer Enable.

0=0 destuffer disabled

1=0 destuffer enabled

DS2151Q

15 of 51

CCR3: COMMON CONTROL REGISTER 3 (Address=30 Hex)

(MSB) (LSB)

ESMDM ESR P16F RSMS PDE TLD TLU LIRST

SYMBOL POSITION NAME AND DESCRIPTION

ESMDM CCR3.7

Elastic Store Minimum Delay Mode.

See Section 10.3 for

details.

0=elastic stores operate at full two-frame depth

1=elastic stores operate at 32-bit depth

ESR CCR3.6

Elastic Store Reset.

Setting this bit from a 0 to a 1 will force

the elastic stores to a known depth. Should be toggled after

SYSCLK has been applied and is stable. Must be cleared and

set again for a subsequent reset.

P16F CCR3.5 Function of Pin 16.

0=Receive Loss of Sync (RLOS).

1=Loss of Transmit Clock (LOTC).

RSMS CCR3.4

RSYNC Multiframe Skip Control.

Useful in framing format

conversions from D4 to ESF.

0=RSYNC will output a pulse at every multiframe

1=RSYNC will output a pulse at every other multiframe note:

for this bit to have any affect, the RSYNC must be set to output

multiframe pulses (RCR2.4=1 and RCR2.3=0) and the receive

elastic store must be bypassed. (CCR1.2 = 0).

PDE CCR3.3 Pulse Density Enforcer Enable.

0=disable transmit pulse density enforcer

1=enable transmit pulse density enforcer

TLD CCR3.2 Transmit Loop Down Code (001).

0=transmit data normally

1=replace normal transmitted data with Loop Down code

TLU CCR3.1 Transmit Loop Up Code (00001).

0=transmit data normally

1=replace normal transmitted data with Loop Up code

LIRST CCR3.0

Line Interface Reset.

Setting this bit from a 0 to a one will

initiate an internal reset that affects the slicer, AGC, clock

recovery state machine and jitter attenuator. Normally this bit is

only toggled on power-up. Must be cleared and set again for a

subsequent reset.

LOOP CODE GENERATION

When either the CCR3.1 or CCR3.2 bits are set to 1, the DS2151Q will replace the normal transmitted

payload with either the Loop Up or Loop Down code respectively. The DS2151Q will overwrite the

repeating loop code pattern with the framing bits. The SCT will continue to transmit the loop codes as

long as either bit is set. It is an illegal state to have both CCR3.1 and CCR3.2 set to 1 at the same time.

DS2151Q

16 of 51

PULSE DENSITY ENFORCER

The SCT always examines both the transmit and receive data streams for violations of the following rules

which are required by ANSI T1.403-199X:

– no more than 15 consecutive 0s

– at least N 1s in each and every time window of 8 x (N +1) bits where N=1 through 23

Violations for the transmit and receive data streams are reported in the RIR2.0 and RIR2.1 bits

respectively.

When the CCR3.3 is set to 1, the DS2151Q will force the transmitted stream to meet this requirement no

matter the content of the transmitted stream. When running B8ZS, the CCR3.3 bit should be set to 0,

since B8ZS encoded data streams cannot violate the pulse density requirements.

POWER-UP SEQUENCE

On power-up, after the supplies are stable, the DS2151Q should be configured for operation by writing to

all of the internal registers (this includes setting the Test Register to 00Hex) since the contents of the

internal registers cannot be predicted on power-up. Next, the LIRST bit should be toggled from 0 to 1 to

reset the line interface (it will take the DS2151Q about 40 ms to recover from the LIRST being toggled).

Finally, after the SYSCLK input is stable, the ESR bit should be toggled from a 0 to a 1 (this step can be

skipped if the elastic stores are disabled).

4.0 STATUS AND INFORMATION REGISTERS

There is a set of four registers that contain information on the current real time status of the DS2151Q:

Status Register 1 (SR1), Status Register 2 (SR2), Receive Information Register 1 (RIR1), and Receive

Information Register 2 (RIR2). When a particular event has occurred (or is occurring), the appropriate bit

in one of these four registers will be set to a 1. All of the bits in these registers operate in a latched

fashion. This means that if an event occurs and a bit is set to a 1 in any of the registers, it will remain set

until the user reads that bit. The bit will be cleared when it is read and it will not be set again until the

event has occurred again or if the alarm(s) is still present.

The user will always precede a read of these registers with a write. The byte written to the register will

inform the DS2151Q which bits the user wishes to read and have cleared. The user will write a byte to

one of these four registers, with a 1 in the bit positions he or she wishes to read and a 0 in the bit positions

he or she does not wish to obtain the latest information on. When a 1 is written to a bit location, the read

a bit position, the read register will not be updated and the previous value will be held. A write to the

status and information registers will be immediately followed by a read of the same register. The read

result should be logically AND’ed with the mask byte that was just written and this value should be

written back into the same register to insure that the bit does indeed clear. This second write is necessary

because the alarms and events in the status registers occur asynchronously in respect to their access via

the parallel port. The write-read-write scheme is unique to the four status registers and it allows an

external microcontroller or microprocessor to individually poll certain bits without disturbing the other

bits in the register. This operation is key in controlling the DS2151Q with higher-order software

languages.

The SR1 and SR2 registers have the unique ability to initiate a hardware interrupt via the INT1 and INT2

pins respectively. Each of the alarms and events in the SR1 and SR2 can be either masked or unmasked

DS2151Q

17 of 51

from the interrupt pins via the Interrupt Mask Register 1 (IMR1) and Interrupt Mask Register 2 (IMR2)

respectively.

RIR1: RECEIVE INFORMATION REGISTER 1 (Address=22 Hex)

(MSB) (LSB)

COFA 8ZD 16ZD RESF RESE SEFE B8ZS FBE

SYMBOL POSITION NAME AND DESCRIPTION

COFA RIR1.7

Change of Frame Alignment.

Set when the last resync

resulted in a change of frame or multiframe alignment.

8ZD RIR1.6

Eight 0 Detect.

Set when a string of eight consecutive 0s have

been received at RPOS and RNEG.

16ZD RIR1.5

Sixteen 0 Detect.

Set when a string of 16 consecutive 0s have

been received at RPOS and RNEG.

RESF RIR1.4

Receive Elastic Store Full.

Set when the receive elastic store

buffer fills and a frame is deleted.

RESE RIR1.3

Receive Elastic Store Empty.

Set when the receive elastic

store buffer empties and a frame is repeated.

SEFE RIR1.2

Severely Errored Framing Event.

Set when 2 out of 6

framing bits (Ft or FPS) are received in error.

B8ZS RIR1.1

B8ZS Code Word Detect.

Set when a B8ZS code word is

detected at RPOS and RNEG independent of whether the B8ZS

mode is selected or not via CCR2.6.

FBE RIR1.0

Frame Bit Error.

Set when a Ft (D4) or FPS (ESF) framing

bit is received in error.

DS2151Q

18 of 51

RIR2: RECEIVE INFORMATION REGISTER 2 (Address=31 Hex)

(MSB) (LSB)

RL1 RL0 TESF TESE TSLIP JALT RPDV TPDV

SYMBOL POSITION NAME AND DESCRIPTION

RL1 RIR2.7 Receive Level Bit 1. See Table 4-1.

RL0 RIR2.6 Receive Level Bit 0. See Table 4-1.

TESF RIR2.5

Transmit Elastic Store Full.

Set when the transmit elastic

store buffer fills and a frame is deleted.

TESE RIR2.4

Transmit Elastic Store Empty.

Set when the transmit elastic

store buffer empties and a frame is repeated.

TSLIP RIR2.3

Transmit Elastic Store Slip Occurrence.

Set when the

transmit elastic store has either repeated or deleted a frame.

JALT RIR2.2

Jitter Attenuator Limit Trip.

Set when the jitter attenuator

FIFO reaches to within 4 bits of its limit; useful for debugging

jitter attenuation operation.

RPDV RIR2.1

Receive Pulse Density Violation.

Set when the receive data

stream does not meet the ANSI T1.403 requirements for pulse

density.

TPDV RIR2.0 Transmit Pulse Density Violation. Set when the transmit data

stream does not meet the ANSI T1.403 requirements for pulse

density.

DS2151Q RECEIVE T1 LEVEL INDICATION Table 4-1

RL1 RL0 TYPICAL LEVEL RECEIVED

0 0 +2 dB to -7.5 dB

0 1 -7.5 dB to -15 dB

1 0 -15 dB to -22.5 dB

1 1 less than -22.5 Db

DS2151Q

19 of 51

SR1: STATUS REGISTER 1 (Address=20 Hex)

(MSB) (LSB)

LUP LDN LOTC RSLIP RBL RYEL RCL RLOS

SYMBOL POSITION NAME AND DESCRIPTION

LUP SR1.7

Loop Up Code Detected

. Set when the repeating ...00001...

loop up code is being received.

LDN SR1.6

Loop Down Code Detected

. Set when the repeating ...001...

loop down code is being received.

LOTC SR1.5

Loss of Transmit Clock

. Set when the TCLK pin has not

transitioned for one channel time (or 5.2 us). Will force pin 16

high if enabled via CCR1.6. Based on RCLK.

RSLIP SR1.4

Receive Elastic Store Slip Occurrence

. Set when the receive

elastic store has either repeated or deleted a frame.

RBL SR1.3

Receive Blue Alarm

. Set when a blue alarm is received at

RTIP and RRING. See note below.

RYEL SR1.2 Receive Yellow Alarm. Set when a yellow alarm is received at

RTIP and RRING.

RCL SR1.1 Receive Carrier Loss. Set when 192 consecutive 0s have been

detected at RTIP and RRING.

RLOS SR1.0 Receive Loss of Sync. Set when the device is not synchronized

to the receive T1 stream.

DS2151Q ALARM SET AND CLEAR CRITERIA Table 4-2

ALARM SET CRITERIA CLEAR CRITERIA

Blue Alarm (AIS) (see note 1

below) when over a 3 ms window, five

or less 0s are received when over a 3 ms window, six or

more 0s are received

Yellow Alarm

1. D4 bit 2 mode (RCR2.2=0)

2. D4 12th F-bit mode

(RCR2.2=1; this mode is also

referred to as the “Japanese

Yellow Alarm”)

3. ESF Mode

when bit 2 of 256 consecutive

channels is set to 0 for at least

254 occurrences

when the 12

framing bit is set

to 1 for two consecutive

occurrences

when 16 consecutive patterns of

00FF hex appear in the FDL

when bit 2 of 256 consecutive

channels is set to 0 for less than

254 occurrences

when the 12

framing bit is set

to 0 for two consecutive

occurrences

when 14 or less patterns of 00FF

hex out of 16 possible appear in

the FDL

Red Alarm (RCL) (this alarm is

also referred to as Loss of Signal) when 192 consecutive 0s are

received when 14 or more 1s out of 112

possible bit positions are

received starting with the first 1

received

DS2151Q

20 of 51

NOTE:

1. The definition of Blue Alarm (or Alarm Indication Signal) is an unframed all 1s signal. Blue alarm

detectors should be able to operate properly in the presence of a 10-3 error rate and they should not

falsely trigger on a framed all 1s signal. The blue alarm criteria in the DS2151Q has been set to

achieve this performance. It is recommended that the RBL bit be qualified with the RLOS status bit

in detecting a blue alarm.

LOOP UP/DOWN CODE DETECTION

Bits SR1.7 and SR1.6 will indicate when either the standard Loop Up or Loop Down codes are being

received by the DS2151Q. When a Loop Up code has been received for 5 seconds, the CPE is expected

to loop the recovered data (without correcting BPVs) back to the source. The Loop Down code indicates

that the loopback should be discontinued. See the AT&T publication TR 62411 for more details. The

DS2151Q will detect the Loop Up/Down codes in both framed and unframed circumstances with bit error

rates as high as 10**-2. The loop code detector has a nominal integration period of 48 ms. Hence, after

about 48 ms of receiving either code, the proper status bit will be set to a 1. After this initial indication, it

is recommended that the software poll the DS2151Q every 100 ms to 500 ms until 5 seconds have elapsed

to insure that the code is continuously present. Once 5 seconds have passed, the DS2151Q should be

taken into or out of loopback via the Remote Loopback (RLB) bit in CCR1.

SR2: STATUS REGISTER 2 (Address=21 Hex)

(MSB) (LSB)

RMF TMF SEC RFDL TFDL RMTCH RAF -

SYMBOL POSITION NAME AND DESCRIPTION

RMF SR2.7 Receive Multiframe. Set on receive multiframe boundaries.

TMF SR2.6 Transmit Multiframe. Set on transmit multiframe boundaries.

SEC SR2.5

One Second Timer

. Set on increments of 1 second based on

RCLK; will be set in increments of 999 ms, 999 ms, and 1002

ms every 3 seconds.

RFDL SR2.4

Receive FDL Buffer Full

. Set when the receive FDL buffer

(RFDL) fills to capacity (8 bits).

TFDL SR2.3

Transmit FDL Buffer Empty

. Set when the transmit FDL

buffer (TFDL) empties.

RMTCH SR2.2

Receive FDL Match Occurrence

. Set when the RFDL

matches either RFDLM1 or RFDLM2.

RAF SR2.1

Receive FDL Abort

. Set when eight consecutive 1s are

received in the FDL.

-SR2.0 Not Assigned. Should be set to 0 when written.

DS2151Q

21 of 51

IMR1: INTERRUPT MASK REGISTER 1 (Address=7F Hex)

(MSB) (LSB)

LUP LDN LOTC SLIP RBL RYEL RCL RLOS

SYMBOL POSITION NAME AND DESCRIPTION

LUP IMR1.7 Loop Up Code Detected.

0=interrupt masked

1=interrupt enabled

LDN IMR1.6 Loop Down Code Detected.

0=interrupt masked

1=interrupt enabled

LOTC IMR1.5 Loss of Transmit Clock.

0=interrupt masked

1=interrupt enabled

SLIP IMR1.4 Elastic Store Slip Occurrence.

0=interrupt masked

1=interrupt enabled

RBL IMR1.3 Receive Blue Alarm.

0=interrupt masked

1=interrupt enabled

RYEL IMR1.2 Receive Yellow Alarm.

0=interrupt masked

1=interrupt enabled

RCL IMR1.1 Receive Carrier Loss.

0=interrupt masked

1=interrupt enabled

RLOS IMR1.0 Receive Loss of Sync.

0=interrupt masked

1=interrupt enabled

DS2151Q

22 of 51

IMR2: INTERRUPT MASK REGISTER 2 (Address=6F Hex)

(MSB) (LSB)

RMF TMF SEC RFDL TFDL RMTCH RAF -

SYMBOL POSITION NAME AND DESCRIPTION

RMF IMR2.7 Receive Multiframe.

0=interrupt masked

1=interrupt enabled

TMF IMR2.6 Transmit Multiframe.

0=interrupt masked

1=interrupt enabled

SEC IMR2.5 One-Second Timer.

0=interrupt masked

1=interrupt enabled

RFDL IMR2.4 Receive FDL Buffer Full.

0=interrupt masked

1=interrupt enabled

TFDL IMR2.3 Transmit FDL Buffer Empty.

0=interrupt masked

1=interrupt enabled

RMTCH IMR2.2 Receive FDL Match Occurrence.

0=interrupt masked

1=interrupt enabled

RAF IMR2.1 Receive FDL Abort.

0=interrupt masked

1=interrupt enabled

-IMR2.0 Not Assigned. Should be set to 0 when written to.

5.0 ERROR COUNT REGISTERS

There are a set of three counters in the DS2151Q that record bipolar violations, excessive 0s, errors in the

CRC6 code words, framing bit errors, and number of multiframes that the device is out of receive

synchronization. Each of these three counters are automatically updated on one second boundaries as

determined by the one second timer in Status Register 2 (SR2.5). Hence, these registers contain

performance data from the previous second. The user can use the interrupt from the 1-second timer to

determine when to read these registers. The user has a full second to read the counters before the data is

lost. All three counters will saturate at their respective maximum counts and they will not rollover (note:

only the Line Code Violation Count Register has the potential to overflow).

5.1 Line Code Violation Count Register (LCVCR)

Line Code Violation Count Register 1 (LCVCR1) is the most significant word and LCVCR2 is the least

significant word of a 16-bit counter that records code violations (CVs). CVs are defined as Bipolar

Violations (BPVs) or excessive 0s. See Table 5-1 for details of exactly what the LCVCRs count. If the

DS2151Q

23 of 51

B8ZS mode is set for the receive side via CCR2.2, then B8ZS code words are not counted. This counter

is always enabled; it is not disabled during receive loss of synchronization (RLOS=1) conditions.

LCVCR1: LINE CODE VIOLATION COUNT REGISTER 1 (Address=23 Hex)

LCVCR2: LINE CODE VIOLATION COUNT REGISTER 2 (Address=24 Hex)

(MSB) (LSB)

LCV15 LCV14 LCV13 LCV12 LCV11 LCV10 LCV9 LCV8 LCVCR1

LCV7 LCV6 LCV5 LCV4 LCV3 LCV2 LCV1 LCV0 LCVCR2

SYMBOL POSITION NAME AND DESCRIPTION

LCV15 LCVCR1.7 MSB of the 16-bit code violation count

LCV0 LCVCR2.0 LSB of the 16-bit code violation count

LINE CODE VIOLATION COUNTING ARRANGEMENTS Table 5-1

COUNT EXCESSIVE

0S?

(RCR1.7)

B8ZS ENABLED?

(CCR2.2) WHAT IS COUNTED IN THE

LCVCRs

no no BPVs

yes no BPVs + 16 consecutive 0s

no yes BPVs (B8ZS code words not counted)

yes yes BPVs + 8 consecutive 0s

5.2 Path Code Violation Count Register (PCVCR)

When the receive side of the DS2151Q is set to operate in the ESF framing mode (CCR2.3=1), PCVCR

will automatically be set as a 12-bit counter that will record errors in the CRC6 code words. When set to

operate in the D4 framing mode (CCR2.3=0), PCVCR will automatically count errors in the Ft framing

bit position. Via the RCR2.1 bit, the DS2151Q can be programmed to also report errors in the Fs framing

bit position. The PCVCR will be disabled during receive loss of synchronization (RLOS=1) conditions.

See Table 5-2 for a detailed description of exactly what errors the PCVCR counts.

PCVCR1: PATH VIOLATION COUNT REGISTER 1 (Address=25 Hex)

PCVCR2: PATH VIOLATION COUNT REGISTER 2 (Address=26 Hex)

(MSB) (LSB)

(note 1) (note 1) (note 1) (note 1) CRC/FB11 CRC/FB10 CRC/FB9 CRC/FB8 PCVCR1

CRC/FB7 CRC/FB6 CRC/FB5 CRC/FB4 CRC/FB3 CRC/FB2 CRC/FB1 CRC/FB0 PCVCR2

SYMBOL POSITION NAME AND DESCRIPTION

CRC/FB11 PCVCR1.3 MSB of the 12-Bit CRC6 Error or Frame Bit Error

Count (note 2)

CRC/FB0 PCVCR2.0 LSB of the 12-Bit CRC6 Error or Frame Bit Error Count

(note 2)

NOTES:

1. The upper nibble of the counter at address 25 is used by the Multiframes Out of Sync Count Register.

DS2151Q

24 of 51

2. PCVCR counts either errors in CRC code words (in the ESF framing mode; CCR2.3=1) or errors in

the framing bit position (in the D4 framing mode; CCR2.3=0).

PATH CODE VIOLATION COUNTING ARRANGEMENTS Table 5-2

FRAMING MODE

(CCR2.3) COUNT FS ERRORS?

(RCR2.1) WHAT IS COUNTED

IN THE PCVCRs

D4 no errors in the Ft pattern

D4 yes errors in both the Ft and Fs patterns

ESF don’t care errors in the CRC6 code words

5.3 Multiframes Out of Sync Count Register (MOSCR)

Normally the MOSCR is used to count the number of multiframes that the receive synchronizer is out of

sync (RCR2.0=1). This number is useful in ESF applications needing to measure the parameters Loss Of

Frame Count (LOFC) and ESF Error Events as described in AT&T publication TR54016. When the

MOSCR is operated in this mode, it is not disabled during receive loss of synchronization (RLOS=1)

conditions. The MOSCR has alternate operating mode whereby it will count either errors in the Ft

framing pattern (in the D4 mode) or errors in the FPS framing pattern (in the ESF mode). When the

MOSCR is operated in this mode, it is disabled during receive loss of synchronization (RLOS=1)

conditions. See Table 5-3 for a detailed description of what the MOSCR is capable of counting.

MOSCR1: MULTIFRAMES OUT OF SYNC COUNT REGISTER 1 (Address=25

Hex)

MOSCR2: MULTIFRAMES OUT OF SYNC COUNT REGISTER 2 (Address=27

Hex)

(MSB) (LSB)

MOS/FB11 MOS/FB10 MOS/FB9 MOS/FB8 (note 1) (note 1) (note 1) (note 1) MOSCR1

MOS/FB7 MOS/FB6 MOS/FB5 MOS/FB4 MOS/FB3 MOS/FB2 MOS/FB1 MOS/FB0 MOSCR2

SYMBOL POSITION NAME AND DESCRIPTION

MOS/FB11 MOSCR1.7 MSB of the 12-Bit Multiframes Out of Sync or F-Bit

Error Count (note 2)

MOS/FB0 MOSCR2.0 LSB of the 12-Bit Multiframes Out of Sync or F-Bit Error

Count (note 2)

NOTES:

1. The lower nibble of the counter at address 25 is used by the Path Code Violation Count Register.

2. MOSCR counts either errors in framing bit position (RCR2.0=0) or the number of multiframes out of

sync (RCR2.0=1).

MULTIFRAMES OUT OF SYNC COUNTING ARRANGEMENTS Table 5-3

FRAMING MODE

(CCR2.3) COUNT MOS OR F-BIT

ERRORS? (RCR2.0) WHAT IS COUNTED

IN THE MOSCRs

D4 MOS number of multiframes out of sync

D4 F-Bit errors in the Ft pattern

ESF MOS number of multiframes out of sync

ESF F-Bit errors in the FPS pattern

DS2151Q

25 of 51

6.0 FDL/FS EXTRACTION AND INSERTION

The DS2151Q has the ability to extract/insert data from/into the Facility Data Link (FDL) in the ESF

framing mode and from/into Fs bit position in the D4 framing mode. Since SLC-96 utilizes the Fs bit

position, this capability can also be used in SLC-96 applications. The operation of the receive and

transmit sections will be discussed separately.

6.1 Receive Section

In the receive section, the recovered FDL bits or Fs bits are shifted bit-by-bit into the Receive FDL

DS2151Q will signal an external microcontroller that the buffer has filled via the SR2.4 bit. If enabled

via IMR2.4, the INT2 pin will toggle low indicating that the buffer has filled and needs to be read. The

user has 2 ms to read this data before it is lost. If the byte in the RFDL matches either of the bytes

programmed into the RFDLM1 or RFDLM2 registers, then the SR2.2 bit will be set to a 1 and the INT2

pin will be toggled low if enabled via IMR2.2. This feature allows an external microcontroller to ignore

the FDL or Fs pattern until an important event occurs.

The DS2151Q also contains a 0 destuffer which is controlled via the CCR2.0 bit. In both ANSI T1.403

and TR54016, communications on the FDL follows a subset of a LAPD protocol. The LAPD protocol

states that no more than five 1s should be transmitted in a row so that the data does not resemble an

opening or closing flag (01111110) or an abort signal (11111111). If enabled via CCR2.0, the DS2151Q

will automatically look for five 1s in a row, followed by a 0. If it finds such a pattern, it will

automatically remove the 0. If the 0 destuffer sees six or more 1s in a row followed by a 0, the 0 is not

removed. The CCR2.0 bit should always be set to a 1 when the DS2151Q is extracting the FDL. More

on how to use the DS2151Q in FDL and SLC-96 applications is covered in a separate Application Note.

Also, contact the factory for C code software that implements both ANSI T1.403 and AT&T

TR54016.

RFDL: RECEIVE FDL REGISTER (Address=28 Hex)

(MSB) (LSB)

RFDL7 RFDL6 RFDL5 RFDL4 RFDL3 RFDL2 RFDL1 RFDL0

SYMBOL POSITION NAME AND DESCRIPTION

RFDL7 RFDL.7 MSB of the Received FDL Code

RFDL0 RFDL.0 LSB of the Received FDL Code

The Receive FDL Register (RFDL) reports the incoming Facility Data Link (FDL) or the incoming Fs

bits. The LSB is received first.

RFDLM1: RECEIVE FDL MATCH REGISTER 1 (Address=29 Hex)

RFDLM2: RECEIVE FDL MATCH REGISTER 2 (Address=2A Hex)

(MSB) (LSB)

RFDL7 RFDL6 RFDL5 RFDL4 RFDL3 RFDL2 RFDL1 RFDL0

SYMBOL POSITION NAME AND DESCRIPTION

RFDL7 RFDL.7 MSB of the FDL Match Code

RFDL0 RFDL.0 LSB of the FDL Match Code

DS2151Q

26 of 51

When the byte in the Receive FDL Register matches either of the two Receive FDL Match Registers

(RFDLM1/RFDLM2), SR2.2 will be set to a 1 and the INT2 will go active if enabled via IMR2.2.

6.2 Transmit Section

The transmit section will shift out into the T1 data stream, either the FDL (in the ESF framing mode) or

the Fs bits (in the D4 framing mode) contained in the Transmit FDL register (TFDL). When a new value

is written to the TFDL, it will be multiplexed serially (LSB first) into the proper position in the outgoing

T1 data stream. After the full 8 bits have been shifted out, the DS2151Q will signal the host

microcontroller that the buffer is empty and that more data is needed by setting the SR2.3 bit to a 1. The

INT2 will also toggle low if enabled via IMR2.3. The user has 2 ms to update the TFDL with a new

value. If the TFDL is not updated, the old value in the TFDL will be transmitted once again.

The DS2151Q also contains a 0 stuffer which is controlled via the CCR2.4 bit. In both ANSI T1.403 and

TR54016, communications on the FDL follows a subset of a LAPD protocol. The LAPD protocol states

that no more than five 1s should be transmitted in a row so that the data does not resemble an opening or

closing flag (01111110) or an abort signal (11111111). If enabled via CCR2.4, the DS2151Q will

automatically look for five 1s in a row. If it finds such a pattern, it will automatically insert a 0 after the

five 1s. The CCR2.4 bit should always be set to a 1 when the DS2151Q is inserting the FDL. More on

how to use the DS2151Q in FDL and SLC-96 applications is covered in a separate Application Note.

TFDL: TRANSMIT FDL REGISTER (Address=7E Hex)

(MSB) (LSB)

TFDL7 TFDL6 TFDL5 TFDL4 TFDL3 TFDL2 TFDL1 TFDL0

SYMBOL POSITION NAME AND DESCRIPTION

TFDL7 TFDL.7 MSB of the FDL code to be transmitted

TFDL0 TFDL.0 LSB of the FDL code to be transmitted

The Transmit FDL Register (TFDL) contains the Facility Data Link (FDL) information that is to be

inserted on a byte basis into the outgoing T1 data stream in ESF mode. The LSB is transmitted first. In

D4 operation the TFDL can be the source of the Fs pattern. In this case a 1ch is written to the TFDL

DS2151Q

27 of 51

7.0 SIGNALING OPERATION

The Robbed-Bit signaling bits embedded in the T1 stream can be extracted from the receive stream and

inserted into the transmit stream by the DS2151Q. There is a set of 12 registers for the receive side (RS1

to RS12) and 12 registers on the transmit side (TS1 to TS12). The signaling registers are detailed below.

The CCR1.5 bit is used to control the robbed signaling bits as they appear at RSER. If CCR1.5 is set to

0, then the robbed signaling bits will appear at RSER in their proper position as they are received. If

CCR1.5 is set to a 1, then the robbed signaling bit positions will be forced to a 1 at RSER.

RS1 TO RS12: RECEIVE SIGNALING REGISTERS (Address=60 to 6B Hex)

(MSB) (LSB)

A(8) A(7) A(6) A(5) A(4) A(3) A(2) A(1) RS1 (60)

A(16) A(15) A(14) A(13) A(12) A(11) A(10) A(9) RS2 (61)

A(24) A(23) A(22) A(21) A(20) A(19) A(18) A(17) RS3 (62)

B(8) B(7) B(6) B(5) B(4) B(3) B(2) B(1) RS4 (63)

B(16) B(15) B(14) B(13) B(12) B(11) B(10) B(9) RS5 (64)

B(24) B(23) B(22) B(21) B(20) B(19) B(18) B(17) RS6 (65)

A/C(8) A/C(7) A/C(6) A/C(5) A/C(4) A/C(3) A/C(2) A/C(1) RS7 (66)

A/C(16) A/C(15) A/C(14) A/C(13) A/C(12) A/C(11) A/C(10) A/C(9) RS8 (67)

A/C(24) A/C(23) A/C(22) A/C(1) A/C(20) A/C(19) A/C(18) A/C(17) RS9 (68)

B/D(8) B/D(7) B/D(6) B/D(5) B/D(4) B/D(3) B/D(2) B/D(1) RS10 (69)

B/D(16) B/D(15) B/D(14) B/D(13) B/D(12) B/D(11) B/D(10) B/D(9) RS11 (6A)

B/D(24) B/D(23) B/D(22) B/D(21) B/D(20) B/D(19) B/D(18) B/D(17) RS12 (6B)

SYMBOL POSITION NAME AND DESCRIPTION

D(24) RS12.7 Signaling Bit D in Channel 24

A(1) RS1.0 Signaling Bit A in Channel 1

Each Receive Signaling Register (RS1 to RS12) reports the incoming Robbed-Bit signaling from eight

DS0 channels. In the ESF framing mode, there can be up to 4 signaling bits per channel (A, B, C, and D).

In the D4 framing mode, there are only 2 framing bits per channel (A and B). In the D4 framing mode,

the DS2151Q will replace the C and D signaling bit positions with the A and B signaling bits from the

previous multiframe. Hence, whether the DS2151Q is operated in either framing mode, the user needs

only to retrieve the signaling bits every 3 ms. The bits in the Receive Signaling Registers are updated on

multiframe boundaries so the user can utilize the Receive Multiframe Interrupt in the Receive Status

frozen and not updated during a loss of sync condition (SR1.0=1). They will contain the most recent

signaling information before the “OOF” occurred.

DS2151Q

28 of 51

TS1 TO TS12: TRANSMIT SIGNALING REGISTERS (Address=70 to 7B Hex)

(MSB) (LSB)

A(8) A(7) A(6) A(5) A(4) A(3) A(2) A(1) TS1 (70)

A(16) A(15) A(14) A(13) A(12) A(11) A(10) A(9) TS2 (71)

A(24) A(23) A(22) A(21) A(20) A(19) A(18) A(17) TS3 (72)

B(8) B(7) B(6) B(5) B(4) B(3) B(2) B(1) TS4 (73)

B(16) B(15) B(14) B(13) B(12) B(11) B(10) B(9) TS5 (74)

B(24) B(23) B(22) B(21) B(20) B(19) B(18) B(17) TS6 (75)

A/C(8) A/C(7) A/C(6) A/C(5) A/C(4) A/C(3) A/C(2) A/C(1) TS7 (76)

A/C(16) A/C(15) A/C(14) A/C(13) A/C(12) A/C(11) A/C(10) A/C(9) TS8 (77)

A/C(24) A/C(23) A/C(22) A/C(1) A/C(20) A/C(19) A/C(18) A/C(17) TS9 (78)

B/D(8) B/D(7) B/D(6) B/D(5) B/D(4) B/D(3) B/D(2) B/D(1) TS10 (79)

B/D(16) B/D(15) B/D(14) B/D(13) B/D(12) B/D(11) B/D(10) B/D(9) TS11 (7A)

B/D(24) B/D(23) B/D(22) B/D(21) B/D(20) B/D(19) B/D(18) B/D(17) TS12 (7B)

SYMBOL POSITION NAME AND DESCRIPTION

D(24) TS12.7 Signaling Bit D in Channel 24

A(1) TS1.0 Signaling Bit A in Channel 1

Each Transmit Signaling Register (TS1 to TS12) contains the Robbed-Bit signaling for eight DS0

channels that will be inserted into the outgoing stream if enabled to do so via TCR1.4. In the ESF

framing mode, there can be up to 4 signaling bits per channel (A, B, C, and D). On multiframe

boundaries, the DS2151Q will load the values present in the Transmit Signaling Register into an outgoing

signaling shift register that is internal to the device. The user can utilize the Transmit Multiframe

Interrupt in Status Register 2 (SR2.6) to know when to update the signaling bits. In the ESF framing

mode, the interrupt will come every 3 ms and the user has a full 3 ms to update the TSRs. In the D4

framing mode, there are only 2 framing bits per channel (A and B). However in the D4 framing mode,

the DS2151Q uses the C and D bit positions as the A and B bit positions for the next multiframe. The

DS2151Q will load the values in the TSRs into the outgoing shift register every other D4 multiframe.

8.0 SPECIAL TRANSMIT SIDE REGISTERS

There is a set of seven registers in the DS2151Q that can be used to custom tailor the data that is to be

transmitted onto the T1 line, on a channel by channel basis. Each of the 24 T1 channels can be either

forced to be transparent or to have a user defined idle code inserted into them. Each of these special

registers is defined below.

DS2151Q

29 of 51

TTR1/TTR2/TTR3: TRANSMIT TRANSPARENCY REGISTERS (Address=39 to

3B Hex)

(MSB) (LSB)

CH8 CH7 CH6 CH5 CH4 CH3 CH2 CH1 TTR1 (39)

CH16 CH15 CH14 CH13 CH12 CH11 CH10 CH9 TTR2 (3A)

CH24 CH23 CH22 CH21 CH20 CH19 CH18 CH17 TTR3 (3B)

SYMBOL POSITION NAME AND DESCRIPTION

CH24 TTR3.7 Transmit Transparency Registers.

0=this DS0 channel is not transparent

CH1 TTR1.0 1=this DS0 channel is transparent

Each of the bit positions in the Transmit Transparency Registers (TTR1/TTR2/TTR3) represents a DS0

channel in the outgoing frame. When these bits are set to a 1, the corresponding channel is transparent

(or clear). If a DS0 is programmed to be clear, no Robbed-Bit signaling will be inserted nor will the

channel have Bit 7 stuffing performed. However, in the D4 framing mode, Bit 2 will be overwritten by a

0 when a Yellow Alarm is transmitted. Also the user has the option to prevent the TTR registers from

determining which channels are to have Bit 7 stuffing performed. If the TCR2.0 and TCR1.3 bits are set

to 1, then all 24 T1 channels will have Bit 7 stuffing performed on them regardless of how the TTR

registers are programmed. In this manner, the TTR registers are only affecting which channels are to

have Robbed-Bit signaling inserted into them. Please see Figure 13-9 for more details.

TIR1/TIR2/TIR3: TRANSMIT IDLE REGISTERS (Address=3C to 3E Hex)

(MSB) (LSB)

CH8 CH7 CH6 CH5 CH4 CH3 CH2 CH1 TIR1 (3C)

CH16 CH15 CH14 CH13 CH12 CH11 CH10 CH9 TIR2 (3D)

CH24 CH23 CH22 CH21 CH20 CH19 CH18 CH17 TIR3 (3E)

SYMBOL POSITION NAME AND DESCRIPTION

CH24 TIR3.7 Transmit Idle Registers.

0=do not insert the Idle Code into this DS0 channel

CH1 TIR1.0 1=insert the Idle Code into this channel

TIDR: TRANSMIT IDLE DEFINITION REGISTER (Address=3F Hex)

(MSB) (LSB)

TIDR7 TIDR6 TIDR5 TIDR4 TIDR3 TIDR2 TIDR1 TIDR0

SYMBOL POSITION NAME AND DESCRIPTION

TIDR7 TIDR.7 MSB of the Idle Code

TIDR0 TIDR.0 LSB of the Idle Code

Each of the bit positions in the Transmit Idle Registers (TIR1/TIR2/TIR3) represents a DS0 channel in

the outgoing frame. When these bits are set to a 1, the corresponding channel will transmit the Idle Code

contained in the Transmit Idle Definition Register (TIDR). Robbed-Bit signaling and Bit 7 stuffing will

occur over the programmed Idle Code unless the DS0 channel is made transparent by the Transmit

Transparency Registers.

DS2151Q

30 of 51

9.0 CLOCK BLOCKING REGISTERS

The Receive Channel Blocking Registers (RCBR1/RCBR2/RCBR3) and the Transmit Channel Blocking

Registers (TCBR1/TCBR2/TCBR3) control the RCHBLK and TCHBLK pins respectively. The

RCHBLK and TCHCLK pins are user-programmable outputs that can be forced either high or low during

individual channels. These outputs can be used to block clocks to a UART or LAPD controller in

Fractional T1 or ISDN-PRI applications. When the appropriate bits are set to a 1, the RCHBLK and

TCHCLK pins will be held high during the entire corresponding channel time. See the timing in Section

13 for an example.

RCBR1/RCBR2/RCBR3: RECEIVE CHANNEL BLOCKING REGISTERS

(Address=6C to 6E Hex)

(MSB) (LSB)

CH8 CH7 CH6 CH5 CH4 CH3 CH2 CH1 RCBR1 (6C)

CH16 CH15 CH14 CH13 CH12 CH11 CH10 CH9 RCBR2 (6D)

CH24 CH23 CH22 CH21 CH20 CH19 CH18 CH17 RCBR3 (6E)

SYMBOL POSITION NAME AND DESCRIPTION

CH24 RCBR3.7 Receive Channel Blocking Registers

0=force the RCHBLK pin to remain low during this

channel time

CH1 RCBR1.0 1=force the RCHBLK pin high during this channel time

TCBR1/TCBR2/TCBR3: TRANSMIT CHANNEL BLOCKING REGISTERS

(Address=32 to 34 Hex)

(MSB) (LSB)

CH8 CH7 CH6 CH5 CH4 CH3 CH2 CH1 TCBR1 (32)

CH16 CH15 CH14 CH13 CH12 CH11 CH10 CH9 TCBR2 (33)

CH24 CH23 CH22 CH21 CH20 CH19 CH18 CH17 TCBR3 (34)

SYMBOL POSITION NAME AND DESCRIPTION

CH24 TCBR3.7 Transmit Channel Blocking Registers.

0=force the TCHBLK pin to remain low during this

channel time

CH1 TCBR1.0 1=force the TCHBLK pin high during this channel time

10.0 ELASTIC STORES OPERATION

The DS2151Q has two onboard two-frame (386 bits) elastic stores. These elastic stores have two main

purposes. First, they can be used to rate-convert the T1 data stream to 2.048 Mbps (or a multiple of

2.048 Mbps), which is the E1 rate. Secondly, they can be used to absorb the differences in frequency and

phase between the T1 data stream and an asynchronous (i.e., not frequency locked) backplane clock.

Both elastic stores contain full controlled slip capability which is necessary for this second purpose. The

receive side elastic store can be enabled via CCR1.2 and the transmit side elastic store is enabled via

CCR1.7. The elastic stores can be forced to a known depth via the Elastic Store Reset bit (CCR3.6).

DS2151Q

31 of 51

10.1 Receive Side

If the receive side elastic store is enabled (CCR1.2=1), then the user must provide either a 1.544 MHz

(CCR1.3=0) or 2.048 MHz (CCR1.3=1) clock at the SYSCLK pin. The user has the option of either

providing a frame sync at the RSYNC pin (RCR2.3=1) or having the RSYNC pin provide a pulse on

frame boundaries (RCR2.3=0). If the user wishes to obtain pulses at the frame boundary, then RCR2.4

must be set to 0 and if the user wishes to have pulses occur at the multiframe boundary, then RCR2.4

must be set to 1. If the user selects to apply a 2.048 MHz clock to the SYSCLK pin, then the data output

at RSER will be forced to all 1s every fourth channel and the F-bit will be deleted. Hence channels 1, 5,

9, 13, 17, 21, 25, and 29 (timeslots 0, 4, 8, 12, 16, 20, 24, and 28) will be forced to a 1.

Also, in 2.048 MHz applications, the RCHBLK output will be forced high during the same channels as

the RSER pin. See Section 13 for more details. This is useful in T1 to CEPT (E1) conversion

applications. If the 386-bit elastic buffer either fills or empties, a controlled slip will occur. If the buffer

empties, then a full frame of data (193 bits) will be repeated at RSER and the SR1.4 and RIR1.3 bits will

be set to a 1. If the buffer fills, then a full frame of data will be deleted and the SR1.4 and RIR1.4 bits

will be set to a 1.

10.2 Transmit Side

The transmit side elastic store can only be used if the receive side elastic store is enabled. The operation

of the transmit elastic store is very similar to the receive side; both have controlled slip operation and both

can operate with either a 1.544 MHz or a 2.048 MHz SYSCLK. When the transmit elastic store is

enabled, both the SYSCLK and RSYNC signals are shared by both the elastic stores. Hence, they will

have the same backplane PCM frame and data structure. Controlled slips in the transmit elastic store are

reported in the RIR2.5 bit and the direction of the slip is reported in the RIR2.3 and RIR2.4 bits.

10.3 Minimum Delay Synchronous SYSCLKMode

In applications where the DS2151Q is connected to backplanes that are frequency-locked to the recovered

T1 clock (i.e., the RCLK output), the full two-frame depth of the onboard elastic stores is really not

needed. In fact, in some delay-sensitive applications the normal two-frame depth may be excessive. If

the CCR3.7 bit is set to 1, then the receive elastic store (and also the transmit elastic store if it is enabled)

will be forced to a maximum depth of 32 bits instead of the normal 386 bits. In this mode, the SYSCLK

must be frequency-locked to RCLK and all of the slip contention logic in the DS2151Q is disabled (since

slips cannot occur). Also, since the buffer depth is no longer two frames deep, the DS2151Q must be set

up to source either a frame or multiframe pulse at the RSYNC pin. On power-up after the SYSCLK has

locked to the RCLK signal, the Elastic Store Reset bit (CCR3.6) should be toggled from a 0 to a 1 to

insure proper operation.

11.0 RECEIVE MARK REGISTERS

The DS2151Q has the ability to replace the incoming data on a channel-by-channel basis with either an

idle code (7F Hex) or the digital milliwatt code, which is an 8-byte repeating pattern that represents a 1

kHz sine wave (1E/0B/0B/1E/9E/8B/8B/9E). The RCR2.7 bit will determine which code is used. Each

bit in the RMRs, represents a particular channel. If a bit is set to a 1, then the receive data in that channel

will be replaced with one of the two codes. If a bit is set to 0, no replacement occurs.

DS2151Q

32 of 51

RMR1/RMR2/RMR3: RECEIVE MARK REGISTERS (Address=2D to 2F Hex)

(MSB) (LSB)

CH8 CH7 CH6 CH5 CH4 CH3 CH2 CH1 RMR1 (2D)

CH16 CH15 CH14 CH13 CH12 CH11 CH10 CH9 RMR2 (2E)

CH24 CH23 CH22 CH21 CH20 CH19 CH18 CH17 RMR3 (2F)

SYMBOL POSITION NAME AND DESCRIPTION

CH24 RMR3.7 Receive Channel Blocking Registers.

0=do not affect the receive data associated with this

channel

CH1 RMR1.0 1=replace the receive data associated with this channel

with either the idle code or the digital milliwatt code

(depends on the RCR2.7 bit)

12.0 LINE INTERFACE FUNCTIONS

The line interface function in the DS2151Q contains three sections; (1) the receiver which handles clock

and data recovery, (2) the transmitter which waveshapes and drives the T1 line, and (3) the jitter

attenuator. Each of these three sections is controlled by the Line Interface Control Register (LICR),

which is described below.

LICR: LINE INTERFACE CONTROL REGISTER (Address=7C Hex)

(MSB) (LSB)

L2 L1 L0 EGL JAS JABDS DJA TPD LICR

SYMBOL POSITION NAME AND DESCRIPTION

L2 LICR.7

Line Build Out Select Bit 2.

Sets the transmitter build

out; see the Table 12-2

L1 LICR.6

Line Build Out Select Bit 1

. Sets the transmitter build

out; see the Table 12-2

L0 LICR.5

Line Build Out Select Bit 0

. Sets the transmitter build

out; see the Table 12-2

EGL LICR.4 Receive Equalizer Gain Limit.

0= -36 dB

1= -30 dB

JAS LICR.3 Jitter Attenuator Select.

0=place the jitter attenuator on the receive side

1=place the jitter attenuator on the transmit side

JABDS LICR.2 Jitter Attenuator Buffer Depth Select.

0=128 bits

1=32 bits (use for delay sensitive applications)

DJA LICR.1 Disable Jitter Attenuator.

0=jitter attenuator enabled

DS2151Q

33 of 51

1=jitter attenuator disabled

TPD LICR.0 Transmit Power Down.

0=normal transmitter operation

1=powers down the transmitter and 3-states the TTIP and

TRING pins

12.1 Receive Clock and Data Recovery

The DS2151Q contains a digital clock recovery system. See the DS2151Q Block Diagram in Section 1

and Figure 12-1 for more details. The DS2151Q couples to the receive T1 twisted pair via a 1:1

transformer. See Table 12-3 for transformer details. The DS2151Q automatically adjusts to the T1 signal

being received at the RTIP and RRING pins and can handle T1 lines from 0 feet to over 6000 feet in

length. The crystal attached at the XTAL1 and XTAL2 pins is multiplied by 4 via an internal PLL and

fed to the clock recovery system. The clock recovery system uses both edges of the clock from the PLL

circuit to form a 32 times oversampler which is used to recover the clock and data. This oversampling

technique offers outstanding jitter tolerance (see Figure 12-2). The EGL bit in the Line Interface Control

receiver sensitivity of -30 dB is wholly sufficient and hence the EGL bit should be set to 1. In some

applications, more sensitivity than -30 dB may be required and the DS2151Q will allow the receiver to go

as low as -36 dB if the EGL bit is set to 0. However, when the EGL bit is set to 0, the DS2151Q will be

more susceptible to crosstalk and its jitter tolerance will suffer.

Normally, the clock that is output at the RCLK pin is the recovered clock from the T1 AMI waveform

presented at the RTIP and RRING inputs. When no AMI signal is present at RTIP and RRING, a

Receive Carrier Loss (RCL) condition will occur and the RCLK can be sourced from either the ACLKI

pin or from the crystal attached to the XTAL1 and XTAL2 pins. The DS2151Q will sense the ACLKI

pin to determine if a clock is present. If no clock is applied to the ACLKI pin, then it should be tied to

RVSS to prevent the device from falsely sensing a clock. See Table 12-1. If the jitter attenuator is either

placed in the transmit path or is disabled, the RCLK output can exhibit short high cycles of the clock.

This is due to the highly oversampled digital clock recovery circuitry. If the jitter attenuator is placed in

the receive path (as is the case in most applications), the jitter attenuator restores the RCLK to being close

to 50% duty cycle. Please see the Receive AC Timing Characteristics in Section 14 for more details.

SOURCE OF RCLK UPON RCL Table 12-1

ACLKI PRESENT? RECEIVE SIDE JITTER

ATTENUATOR TRANSMIT SIDE JITTER

ATTENUATOR

Yes ACLKI via the jitter attenuator ACLKI

No centered crystal TCLK via the jitter attenuator

12.2 Transmit Waveshaping and Line Driving

The DS2151Q uses a set of laser-trimmed delay lines along with a precision Digital-to-Analog Converter

(DAC) to create the waveforms that are transmitted onto the T1 line. The waveforms created by the

DS2151Q meet the latest ANSI, AT&T, and CCITT specifications. See Figure 12-3. The user will select

which waveform is to be generated by properly programming the L0 to L2 bits in the Line Interface

Control Register (LICR).

DS2151Q

34 of 51

LBO SELECT IN LICR Table 12-2

L2 L1 L0 LINE BUILD OUT APPLICATION

0000 to 133 feet/0 dB DSX-1/CSU

001 133 to 266 feet DSX-1

010 266 to 399 feet DSX-1

011 399 to 533 feet DSX-1

100 533 to 655 feet DSX-1

1 0 1 -7.5 dB CSU

1 1 0 -15 dB CSU

1 1 1 -22.5 dB CSU

Due to the nature of the design of the transmitter in the DS2151Q, very little jitter (less then 0.005 UIpp

broad-band from 10 Hz to 100 kHz) is added to the jitter present on TCLK. Also, the waveforms that

they create are independent of the duty cycle of TCLK. The transmitter in the DS2151Q couples to the

T1 transmit twisted pair via a 1:1.15 or 1:1.36 step up transformer as shown in Figure 12-1. In order for

the devices to create the proper waveforms, the transformer used must meet the specifications listed in

Table 12-3.

TRANSFORMER SPECIFICATIONS Table 12-3

SPECIFICATION RECOMMENDED VALUE

Turns Ratio 1:1 (receive) and 1:1.15 or 1:1.36 (transmit) ±5%

Primary Inductance 600 µH minimum

Leakage Inductance 1.0 µH maximum

Intertwining Capacitance 40 pF maximum

DC Resistance 1.2 ohms maximum

12.3 JITTER ATTENUATOR

The DS2151Q contains an onboard jitter attenuator that can be set to a depth of either 32 or 128 bits via

the JABDS bit in the Line Interface Control Register (LICR). The 128-bit mode is used in applications

where large excursions of wander are expected. The 32-bit mode is used in delay sensitive applications.

The characteristics of the attenuation are shown in Figure 12-4. The jitter attenuator can be placed in

either the receive path or the transmit path by appropriately setting or clearing the JAS bit in the LICR.

Also, the jitter attenuator can be disabled (in effect, removed) by setting the DJA-bit in the LICR. In

order for the jitter attenuator to operate properly, a crystal with the specifications listed in Table 12-4

below must be connected to the XTAL1 and XTAL2 pins. The jitter attenuator divides the clock

provided by the 6.176 MHz crystal at the XTAL1 and XTAL2 pins to create an output clock that contains

very little jitter. Onboard circuitry will pull the crystal (by switching in or out load capacitance) to keep it

long-term averaged to the same frequency as the incoming T1 signal. If the incoming jitter exceeds either

120UIpp (buffer depth is 128 bits) or 28 UIpp (buffer depth is 32 bits), then the DS2151Q will divide the

attached crystal by either 3.5 or 4.5 instead of the normal 4 to keep the buffer from overflowing. When

the device divides by either 3.5 or 4.5, it also sets the Jitter Attenuator Limit Trip (JALT) bit in the

Receive Information Register 2 (RIR2.2).

DS2151Q

35 of 51

CRYSTAL SELECTION GUIDELINES Table 12-4

PARAMETER SPECIFICATION

Parallel Resonant Frequency 6.176 MHz

Mode Fundamental

Load Capacitance 18 pF to 20 pF (18.5 pF nominal)

Tolerance ±50 ppm

Pullability CL=10 pF, delta frequency=+175 to +250 ppm

CL=45 pF, delta frequency=-175 to -250 ppm

Effective Series Resistance 40 ohms maximum

Crystal Cut AT

DS2151Q EXTERNAL ANALOG CONNECTIONS Figure 12-1

NOTE:

See the separate Application Note for details on how to construct a protected interface.

DS2151Q

36 of 51

DS2151Q JITTER TOLERANCE Figure 12-2

DS2151Q TRANSMIT WAVEFORM TEMPLATE Figure 12-3

DS2151Q

37 of 51

DS2151Q JITTER ATTENUATION Figure 12-4

13.0 TIMING DIAGRAMS

RECEIVE SIDE D4 TIMING Figure 13-1

NOTES:

1. RSYNC in the frame mode (RCR2.4=0) and double-wide frame sync is not enabled (RCR2.5=0).

2. RSYNC in the frame mode (RCR2.4=0) and double-wide frame sync is enabled (RCR2.5=1).

3. RSYNC in the multiframe mode (RCR2.4=1).

4. RLINK data (S-bit) is updated 1 bit prior to even frames and held for two frames.

DS2151Q

38 of 51

RECEIVE SIDE ESF TIMING Figure 13-2

NOTES:

1. RSYNC in the frame mode (RCR2.4=0) and double-wide frame sync is not enabled (RCR2.5=0).

2. RSYNC in the frame mode (RCR2.4=0) and double-wide frame sync is enabled (RCR2.5=1).

3. RSYNC in the multiframe mode (RCR2.4=1).

4. ZBTSI mode disabled (RCR2.6=0).

5. RLINK data (FDL bits) is updated 1 bit-time before odd frames and held for two frames.

6. ZBTSI mode is enabled (RCR2.6=1).

7. RLINK data (Z bits) is updated 1 bit-time before odd frame and held for four frames.

DS2151Q

39 of 51

RECEIVE SIDE BOUNDARY TIMING WITH ELASTIC STORE(S) DISABLED

Figure 13-3

NOTES:

1. RCHBLK is programmed to block channel 24.

2. An ESF boundary is shown.

1.544 MHz BOUNDARY TIMING WITH ELASTIC STORE(S) ENABLED

Figure 13-4

NOTES:

1. RSYNC is in the output mode (RCR2.3=0).

2. RSYNC is in the input mode (RCR2.3=1).

3. RCHBLK is programmed to block channel 24.

DS2151Q

40 of 51

2.048 MHz BOUNDARY TIMING WITH ELASTIC STORE(S) ENABLED

Figure 13-5

NOTES:

1. RSER data in channels 1, 5, 9, 13, 17, 21, 25, and 29 are forced to 1; TSER ignored during these

channels.

2. RSYNC is in the output mode (RCR2.3=0).

3. RSYNC is in the input mode (RCR2.3=1).

4. RCHBLK is forced to 1 in the same channels as RSER (see Note 1).

TRANSMIT SIDE D4 TIMING Figure 13-6

NOTES:

1. TSYNC in the frame mode (TCR2.3=0) and double-wide frame sync is not enabled (TCR2.4=0).

2. TSYNC in the frame mode (TCR2.3=0) and double-wide frame sync is enabled (TCR2.4=1).

3. TSYNC in the multiframe mode (TCR2.3=1).

4. TLINK data (S-bit) is sampled during the F-bit position of even frames for insertion into the outgoing

T1 stream when enabled via TCR1.2.

DS2151Q

41 of 51

TRANSMIT SIDE ESF TIMING Figure 13-7

NOTES:

1. TSYNC in the frame mode (TCR2.3=0) and double-wide frame sync is not enabled (TCR2.4=0).

2. TSYNC in the frame mode (TCR2.3=0) and double-wide frame sync is enabled (TCR2.4=1).

3. TSYNC in the multiframe mode (TCR2.4=1).

4. ZBTSI mode disabled (TCR2.5=0).

5. TLINK data (FDL bits) is sampled during the F-bit time of odd frame and inserted into the outgoing

T1 stream if enabled via TCR1.2.

6. ZBTSI mode is enabled (TCR2.5=1).

7. TLINK data (Z bits) is sampled during the F-bit time of frame 1, 5, 9, 13, 17, and 21 and inserted into

the outgoing stream if enabled via TCR1.2.

DS2151Q

42 of 51

TRANSMIT SIDE BOUNDARY TIMING (WITH ELASTIC STORE(S) DISABLED)

Figure 13-8

NOTES:

1. TSYNC is in the input mode (TCR2.2=0).

2. TSYNC is in the output mode (TCR2.2=1).

3. TCHBLK is programmed to block channel 1.

4. See Figures 13-4 and 13-5 for details on timing with the transmit side elastic store enabled.

DS2151Q

43 of 51

DS2151Q TRANSMIT DATA FLOW Figure 13-9

DS2151Q

44 of 51

ABSOLUTE MAXIMUM RATINGS*

Voltage on Any Pin Relative to Ground -1.0V to +7.0V

Operating Temperature 0°C to 70°C (-40°C to +85°C for DS2151QN)

Storage Temperature -55°C to +125°C

Soldering Temperature 260°C for 10 seconds

* This is a stress rating only and functional operation of the device at these or any other conditions above

those indicated in the operation sections of this specification is not implied. Exposure to absolute

maximum rating conditions for extended periods of time may affect reliability.

RECOMMENDED DC (0°C to 70°C)

OPERATING CONDITIONS (-40°C to +85°C for DS2151QN)

PARAMETER SYMBOL MIN TYP MAX UNITS NOTES

Logic 1 VIH 2.0 VDD +0.3 V

Logic 0 VIL -0.3 +0.8 V

Supply VDD 4.75 5.25 V1

CAPACITANCE (tA=25°C)

PARAMETER SYMBOL MIN TYP MAX UNITS NOTES

Input Capacitance CIN 5pF

Output Capacitance COUT 7pF

DC CHARACTERISTICS (0°C to 70°C; VDD =5V ± 5%)

(-40°C to +85°C for DS2151QN)

PARAMETER SYMBOL MIN TYP MAX UNITS NOTES

Supply Current @ 5V IDD 65 mA 2

Input Leakage IIL -1.0 +1.0 µA3

Output Leakage ILO 1.0 µA4

Output Current (2.4V) IOH -1.0 mA

Output Current (0.4V) IOL +4.0 mA

NOTES:

1. Applies to RVDD, TVDD, and DVDD.

2. TCLK=1.544 MHz.

3. 0.0V < VIN < VDD.

4. Applies to INT1 and INT1 when 3-stated.

DS2151Q

45 of 51

AC CHARACTERISTICS (0°C to 70°C; VDD = 5V ± 5%)

PARALLEL PORT (-40°C to +85°C for DS2151QN)

PARAMETER SYMBOL MIN TYP MAX UNITS NOTES

Cycle Time tCYC 250 ns

Pulse Width, DS Low or

High PWEL 150 ns

Pulse Width, DS High or

Low PWEH 100 ns

Input Rise/Fall Times tR , tF30 ns

R/W Hold Time tRWH 10 ns

R/W Setup Time before DS

High tRWS 50 ns

CS Setup Time before DS,

WR or

active tCS 20 ns

CS Hold Time tCH 0ns

Read Data Hold Time tDHR 10 50 ns

Write Data Hold Time tDHW 0ns

Muxed Address Valid to AS

or ALE fall tASL 20 ns

Muxed Address Hold Time tAHL 10 ns

Delay Time DS, WR or

to AS or ALE Rise tASD 25 ns

Pulse Width AS or ALE High PWASH 40 ns

Delay Time, AS or ALE to

DS, WR or

tASED 20 ns

Output Data Delay Time from

DS or

tDDR 20 100 ns

Data Setup Time tDSW 80 ns

INTEL BUS READ AC TIMING

DS2151Q

46 of 51

INTEL BUS WRITE AC TIMING

MOTOROLA BUS AC TIMING

DS2151Q

47 of 51

AC CHARACTERISTICS (0°C to 70°C; VDD = 5V ± 5%)

PARALLEL PORT (-40°C to +85°C for DS2151QN)

PARAMETER SYMBOL MIN TYP MAX UNITS NOTES

ACLKI/RCLK Period tCP 648 ns

RCLK Pulse Width tCH

tCL

230

230 324

324 ns

ns 1

RCLK Pulse Width tCH

tCL

115

115 ns

ns 2

SYSCLK Period tSP

tSP

648

488 ns

ns 3

SYSCLK Pulse Width tSH

tSL

75 ns

RSYNC Set Up to SYSCLK

Falling tSU 25 tSH -5 ns

RSYNC Pulse Width tPW 50 ns

SYSCLK Rise/Fall Times tR

25 ns

Delay RCLK or SYSCLK to

RSER Valid tDD 10 80 ns

Delay RCLK or SYSCLK to

RCHCLK tD1 10 90 ns

Delay RCLK or SYSCLK to

RCHBLK tD2 10 90 ns

Delay RCLK or SYSCLK to

RSYNC tD3 10 80 ns

Delay RCLK to RLCLK tD4 10 80 ns

Delay RCLK to RLINK Valid tD5 10 110 ns

NOTES:

1. Jitter attenuator enabled in the receive side path.

2. Jitter attenuator disabled or enabled in the transmit path.

3. SYSCLK=1.544 MHz

4. SYSCLK=2.048 MHz

DS2151Q

48 of 51

RECEIVE SIDE AC TIMING

NOTES:

1. RSYNC is in the output mode (RCR2.3=0).

2. RSYNC is in the input mode (RCR2.3=1).

3. RLCLK and RLINK only have a timing relationship to RCLK.

4. RCLK can exhibit a short high time if the jitter attenuator is either disabled or in the transmit path.

DS2151Q

49 of 51

AC CHARACTERISTICS - (0°C to 70°C; VDD = 5V ± 5%)

TRANSMIT SIDE (-40°C to +85°C for DS2151QN)

PARAMETER SYMBOL MIN TYP MAX UNITS NOTES

TCLK Period tP648 ns

TCLK Pulse Width tCH

tCL

75 ns

TSER and TLINK Set up to

TCLK Falling tSU 25 ns 1

TSER and TLINK Hold from

TCLK Falling tHD 25 ns 1

TSYNC Set up to TCLK

Falling tSU 25 tCH -5

TSYNC Pulse Width tPW 50

TCLK Rise/Fall Times tR

25 ns

Delay TCLK to TCHCLK tD1 10 60 ns

Delay TCLK to TCHBLK tD2 10 70 ns

Delay TCLK to TSYNC tD3 10 60 ns

Delay TCLK to TLCLK tD4 10 60 ns

NOTE:

If the transmit side elastic store is enabled, then TSER is sampled on the falling edge of SYSCLK and the

parameters tSU and tHD still apply.

DS2151Q

50 of 51

TRANSMIT SIDE AC TIMING

NOTES:

1. TSYNC is in the output mode (TCR2.2=1).

2. TSYNC is in the input mode (TCR2.2=0).

3. TSER is sampled on the falling edge of SYSCLK if the transmit side elastic store is enabled.

DS2151Q

51 of 51

DS2151Q T1 CONTROLLER 44-PIN PLCC