123
FIBER
SENSORS
LASER
SENSORS
PHOTOELECTRIC
SENSORS
MICRO
PHOTOELECTRIC
SENSORS
AREA
SENSORS
SAFETY
COMPONENTS
PRESSURE
SENSORS
INDUCTIVE
PROXIMITY
SENSORS
PARTICULAR
USE SENSORS
SENSOR
OPTIONS
WIRE-SAVING
SYSTEMS
MEASUREMENT
SENSORS
STATIC CONTROL
DEVICES
LASER
MARKERS
Selection
Guide
Fiber Sensor
Amplifiers
FX-300
FX-100
Fibers
FT / FD / FR
FX-410
FX-311
FX-11A
FX-301-F
Other
Products
FIBER
SENSORS
FX-100
Fiber Sensor
Amplifi ers
Related Information
Digital Fiber Sensor
FX-100 SERIES
Glossary of terms / General precautions ...
P.983~ / P.986~
■
Taking fi ber sensors to the next level
Conforming to
EMC Directive
The dual digital display allows users to check both the threshold
value and incident light intensity at the same time, allowing
for clear and intuitive control of the sensor’s functions. The
threshold value can be adjusted simply by pressing the (UP)
key or the (DOWN) key, so that the output operation can be
controlled with high precision, directly from the RUN mode.
Setup is made simple, using a dual digital display
Commercially-available connectors are used so that lead time and spare part numbers
can both be reduced
The connectors used are commercially-available connectors,
so that processing costs and lead time required for carrying
out processing after purchase of the sensors can be greatly
reduced. The same connection parts as the DP-100 series
of digital pressure sensors and the PM-64 series of micro
photoelectric sensors can be used.
Fiber selection
................................. P.63~■
General terms and conditions ............. P.1■
Sensor selection guide
........P.11~ / P.61~■
PNP output
type available
Timer
Light intensity
monitor
Interference
prevention
A
utomatic
sensitivity setting
Test input
Conventional (cable type)
From now on (built-in connector type)
Using cables with connectors
1 Sensor purchase and preparation
2 Harness processing by outside order
1 Sensor purchase and preparation
2 Harness processing by outside order
1
Purchase of sensors and cable with connectors
Conventional lead time
Customer
Harness
processor
Customer
Customer
Harness
processor
Sensor preparation
Sensor preparation
Harness Processing
Harness Processing
Sensor installation
Reduced
Sensor installation
Reduced
Sensor preparation Sensor installation
Lead time from now on
Lead time further reduced
Reduced
lead time
●
Harness processing by outside order after sensor preparation
●
Harness processing by outside order
Commercially-available press-fi t connectors are used, so that the processing
costs for connection cables can be greatly reduced.
Threshold value Incident light intensity
Connection with a
commercially-available
connector
http://www.sunx.com
SUNX website
Digital Fiber Sensor FX-100 SERIES
124
FIBER
SENSORS
LASER
SENSORS
PHOTOELECTRIC
SENSORS
MICRO
PHOTOELECTRIC
SENSORS
AREA
SENSORS
SAFETY
COMPONENTS
PRESSURE
SENSORS
INDUCTIVE
PROXIMITY
SENSORS
PARTICULAR
USE SENSORS
SENSOR
OPTIONS
WIRE-SAVING
SYSTEMS
MEASUREMENT
SENSORS
STATIC CONTROL
DEVICES
LASER
MARKERS
Selection
Guide
Fiber Sensor
Amplifiers
FX-300
FX-100
Fibers
FT / FD / FR
FX-410
FX-311
FX-11A
FX-301-F
Other
Products
FIBER
SENSORS
FX-100
Fiber sensor
Amplifi ers
The sensor is very slim, yet equipped with a dual digital
display. Both space saving and ease of use have been
achieved.
A stable amount of emitted light is ensured due to control
of the aging of the emitting element to the maximum limit.
Saving-space with a width of 9 mm 0.354 in
Equipped with a four-chemical emitting element
9 mm
0.354 in
Quick code input function [RUN mode]
Sensor settings can be made simply by selecting preset
values.
A three level navigation structure provides easy access to the sensor’s functions, from
basic to advanced
Setting details are divided into three levels for simple operation, so that settings for normal operation are made in
“RUN mode”, basic settings are made in “SET mode”, and advanced functions are set in “PRO mode”. This makes
confi guration much easier to understand and carry out.
Functions used during normal operation
[Function table]
•
Changing threshold values
•
Key lock
• Quick settings • Code settings
RUN mode
SET mode
Functions used when initializing the
sensor and carrying out maintenance
[Function table]
• Teaching • L-ON / D-ON setting
• Timer setting
• Attenuation function
• Interference prevention function
PRO mode
Equipped with a full complement
of digital fiber sensor functions
[Function table]
• Shift • External input • Reset
• GETA • ECO •
Display reversing
• Surplus value display • Copy
•
Threshold tracking
RUN MODE
SET MODE
PRO MODE
Simple setting
Special and detailed setting
Smooth support via telephone [RUN mode]
Confi rmation can be carried out smoothly via telephone
by simply quoting numbers. This can be of great
assistance when dealing with foreign country customers.
No. Output
operation
Light-emitting
amount selection
Timer
Dark-ON OFF None
Dark-ON ON None
Dark-ON OFF
OFF-delay 10 ms
Dark-ON ON
OFF-delay 10 ms
Light-ON ON
ON-delay 40 ms
Light-ON OFF
ON-delay 40 ms
Light-ON ON
ON-delay 10 ms
Light-ON OFF
ON-delay 10 ms
Quick setting numbers (summary)
P.138
DIMENSIONS
P.136 ~
PRECAUTIONS FOR PROPER USE
P.135 ~
SENSING CHARACTERISTICS
P.134 ~
I/O CIRCUIT DIAGRAMS
P.133
SPECIFICATIONS
P.128 ~
LIST OF FIBERS
P.126 ~
ORDER GUIDE
[Stable sensing comparison]
Three-chemical
emitting element
FX-100
Light-emitting
amount
Time
Long-term
stability
125
Digital Fiber Sensor FX-100 SERIES
FIBER
SENSORS
LASER
SENSORS
PHOTOELECTRIC
SENSORS
MICRO
PHOTOELECTRIC
SENSORS
AREA
SENSORS
SAFETY
COMPONENTS
PRESSURE
SENSORS
INDUCTIVE
PROXIMITY
SENSORS
PARTICULAR
USE SENSORS
SENSOR
OPTIONS
WIRE-SAVING
SYSTEMS
MEASUREMENT
SENSORS
STATIC CONTROL
DEVICES
LASER
MARKERS
FIBER
SENSORS
Selection
Guide
Fiber Sensor
Amplifiers
FX-300
FX-100
Fibers
FT / FD / FR
FX-410
FX-311
FX-11A
FX-301-F
Other
Products
FX-100
Fiber Sensor
Amplifi ers
The emitted light and output indicator flash
at the same frequency.
Attenuation function [SET mode]
If the light receiving level becomes saturated when
sensing over short distances or when sensing
transparent objects or minute objects, the light emitting
amount can be reduced so that stable sensing can be
provided without needing to change the response time.
Teaching using ON / OFF buttons [SET mode]
Simply press the ON button when an object is present
and OFF when it is not. There is no need to switch
settings or make judgments between Light-ON ( )
and Dark-ON ( ).
Interference prevention function [SET mode]
The emission frequencies can be set separately for
each unit in order to avoid interference. The emitted light
fl ashes while setting is in progress, so that you can see
at a glance which fi ber sensor is currently being set.
In addition, this interference prevention is not done by
using optical communication. This means that there is no
need to place the amplifi ers close together like there was
before, and so the amplifi ers can be set up apart from
each other.
FX-101□: Interference prevention for up to 3 units
FX-102□: Interference prevention for up to 4 units
Multi-function external input [PRO mode]
Settings such as emission
halt, limit / auto teaching
and ECO settings can be
carried out via external
input.
(Brown) +V
(Blue) 0 V
(White) External input
(Black) Output
External input lines are
equipped as standard
Alert function [PRO mode]
When the amount light received approaches the
threshold value, the display can be made to blink in
order to alert the operator.
* When the emission frequencies are changed, the response times will
also change.
Thru-beam type / Retroreflective type
<Setting example>
Reflective type
Object present ON Object absent OFF
Object present ON Object absent OFF
Limit teaching function
This carries out teaching and sets threshold values only
when no object is present (when the incident light amount
is stable). This is useful when sensing objects if there
are other objects in the background and when sensing
minute objects. Teaching can also be carried out using
external input.
Threshold tracking function [PRO mode]
This function seeks changes
in the light emitting amount
resulting from changes in
the environment over long
periods (such as dust levels),
so that the incident light
intensity can be checked
at desired intervals and the
threshold values can be reset
automatically. Time
Current value
The amount of light
received when there
is no object
Incident light intensity
Threshold value
GETA function [PRO mode]
The display value for the incident light intensity can be offset
by the desired value (target value). The target value can be set
to between 0 and 2,000 (in increments of 100). For example, if
the incident light intensity is 1,500 and the target value is set to
2,000, then “2,000” will appear in the digital display.
Unify at 500 using
the GETA function
Variations in the amount of light received
<When using at a shift amount of 20% and a threshold value of 1,000>
The amount of light received ranges from about 900 to 1,100
when the digital indicator flashes.
Range of the digital indicator flashing
(margin: small)
1,100 approx.
900 approx.
Threshold value
of 1,000
The digital indicator flashes.
Incident light intensity
Digital Fiber Sensor FX-100 SERIES
126
FIBER
SENSORS
LASER
SENSORS
PHOTO-
ELECTRIC
SENSORS
MICRO
PHOTO-
ELECTRIC
SENSORS
AREA
SENSORS
SAFETY
COMPONENTS
PRESSURE
SENSORS
INDUCTIVE
PROXIMITY
SENSORS
PARTICULAR
USE
SENSORS
SENSOR
OPTIONS
WIRE-
SAVING
SYSTEMS
MEASURE-
MENT
SENSORS
STATIC
CONTROL
DEVICES
LASER
MARKERS
Selection
Guide
Fiber Sensor
Amplifiers
FX-300
FX-100
Fibers
FT / FD / FR
FX-410
FX-311
FX-11A
FX-301-F
Other
Products
FIBER
SENSORS
FX-100
Fiber Sensor
Amplifi ers
Amplifi ers
Type Appearance Model No. Emitting
element Output
Standard type
FX-101 (Note 2)
Red LED
NPN open-collector
transistor
M8 plug-in
connector
type
FX-101-Z (Note 3) NPN open-collector
transistor
FX-101P (Note 2) PNP open-collector
transistor
M8 plug-in
connector
type
FX-101P-Z (Note 3)
PNP open-collector
transistor
Cable set
(Note 1)
FX-101-CC2 NPN open-collector
transistor
FX-101P-CC2 PNP open-collector
collector transistor
Long sensing range type
FX-102 (Note 2) NPN open-collector
transistor
M8 plug-in
connector
type
FX-102-Z (Note 3) NPN open-collector
transistor
FX-102P (Note 2) PNP open-collector
transistor
M8 plug-in
connector
type
FX-102P-Z (Note 3)
PNP open-collector
transistor
Cable set
(Note 1)
FX-102-CC2 NPN open-collector
transistor
FX-102P-CC2 PNP open-collector
transistor
ORDER GUIDE
Accessory
CN-14A-C2•
Connector attached
cable 2 m 6.562 ft
Only include cable set type*
Notes: 1) The connector attached cable CN-14A-C2 is supplied with the amplifi er.
2) Make sure to use the optional connector attached cable CN-14A(-R)-C□ or the connector CN-14A, or a connector manufactured by J.S.T. Mfg. Co., Ltd.
(contact: SPHD-001T-P0.5, housing: PAP-04V-S)
3) Make sure to use the optional M8 connector attached cable CN-24A-C□.
Designation Model No. Description
Connector
attached cable
CN-14A-C1 1 m 3.281 ft
0.02 mm2 4-core cabtyre cable with connector
on one end
Cable outer diameter: ø3.7 mm ø0.146 in
CN-14A-C2 (Note)
2 m 6.562 ft
CN-14A-C3 3 m 9.843 ft
CN-14A-C5 5 m 16.404 ft
Connector
attached cable
(Flexible type)
CN-14A-R-C1 1 m 3.281 ft
CN-14A-R-C2 2 m 6.562 ft
CN-14A-R-C3 3 m 9.843 ft
CN-14A-R-C5 5 m 16.404 ft
M8 connector
attached cable
CN-24A-C2 2 m 6.562 ft For M8 plug-in connector type
The connector on one end
Cable outer diameter: ø4 mm ø0.157 in
CN-24A-C5 5 m 16.404 ft
Connector CN-14A Set of 10 housings and 40 contacts
Protection cover FC-FX-1 This protects the operating surfaces.
Amplifi er
mounting bracket
MS-DIN-4 Mounting bracket for amplifi er
End plates MS-DIN-E
When it moves depending on the way it is installed on a DIN rail,
these end plates ensure that all amplifi ers are mounted together
in a secure and fully connected manner.
Two pcs.per set
M8 connector attached cable
CN-24A-C□•
Protection cover
FC-FX-1•
OPTIONS
Amplifi er mounting
bracket
MS-DIN-4•
Connector
CN-14A•
Note: The connector attached cable CN-14A-C2 is supplied with the cable set type FX-10□(P)-CC2.
Recommended connector
Recommended crimping tool
Contact: SPHD-001T-P0.5, Housing: PAP-04V-S
(Manufactured by J.S.T. Mfg. Co., Ltd.)
Note: Contact the manufacturer for details of the recommended products.
Model No.: YC-610R
(Manufactured by J.S.T. Mfg. Co., Ltd.)
Note: Contact the manufacturer for details of the recommended products.
Contact
Housing
ø9
ø0.354
31.4
1.236 ø4
ø0.157
M8 connector
attached cable
CN-24A-C□
Fixing ring
Connector
attached cable
CN-14A(-R)-C□•
127
Digital Fiber Sensor FX-100 SERIES
FIBER
SENSORS
LASER
SENSORS
PHOTO-
ELECTRIC
SENSORS
MICRO
PHOTO-
ELECTRIC
SENSORS
AREA
SENSORS
SAFETY
COMPONENTS
PRESSURE
SENSORS
INDUCTIVE
PROXIMITY
SENSORS
PARTICULAR
USE
SENSORS
SENSOR
OPTIONS
WIRE-
SAVING
SYSTEMS
MEASURE-
MENT
SENSORS
STATIC
CONTROL
DEVICES
LASER
MARKERS
Selection
Guide
Fiber Sensor
Amplifiers
FX-300
FX-100
Fibers
FT / FD / FR
FX-410
FX-311
FX-11A
FX-301-F
Other
Products
FIBER
SENSORS
FX-100
Fiber sensor
Ampilifi ers
Model No. Sensing range (mm in) (Note 1)
Dimensions
Standard type FX-101□
Long sensing range type FX-102□
FT-A8 1,500 59.055
3,500 137.795 (Note 2)
P.106
FT-A30
3,500 137.795 (Note 2) 3,500 137.795 (Note 2)
P.106
FT-AFM2 280 11.024 720 28.346 P.106
FT-AFM2E 240 9.449 670 26.378 P.106
FT-B8 400 15.748 1,150 45.276 P.106
FT-E12 6 0.236 19 0.748 P.106
FT-E22 15 0.591 60 2.362 P.106
FT-FM2
300 11.811 800 31.496
P.106
FT-FM2S P.106
FT-FM2S4 P.106
FT-FM10L 9,300 366.141 15,000 590.550 P.106
FT-H13-FM2 250 9.843 700 27.559 P.106
FT-H20-J20-S (Note 3)
135 5.315 420 16.535
P.107
FT-H20-J30-S (Note 3)
P.107
FT-H20-J50-S (Note 3)
P.107
FT-H20-M1 210 8.268 540 21.260 P.107
FT-H20-VJ50-S (Note 3)
150 5.906 500 19.685
P.107
FT-H20-VJ80-S (Note 3)
P.107
FT-H20W-M1 100 3.937 300 11.811 P.107
FT-H30-M1V-S (Note 4)
110 4.331 280 11.024 P.107
FT-H35-M2 170 6.693 490 19.291
P.107
FT-H35-M2S6 P.107
FT-HL80Y 990 38.976 2,340 92.126 P.107
FT-K8 1,000 39.370 3,000 118.110 P.108
FT-KV1 135 5.315 500 19.685 P.108
FT-KV8 1,000 39.370 3,000 118.110 P.108
FT-L80Y 1,100 43.307 2,600 102.362 P.108
FT-NFM2
130 5.118 280 11.024
P.108
FT-NFM2S P.108
FT-NFM2S4 P.108
FT-P2 120 4.724 330 12.992 P.108
FT-P40 80 3.150 240 9.449 P.108
FT-P60 130 5.118 300 11.811 P.108
FT-P80 230 9.055 650 25.591 P.108
FT-P81X 260 10.236 800 31.496 P.108
Notes: 1) Please take care that the sensing range of the free-cut type fi ber may be reduced by 20 % max. depending upon how the fi ber is cut.
2) The fi ber cable length practically limits the sensing range to 3,500 mm 137.795 in long.
3) Heat-resistant joint fi bers and ordinary-temperature side fi bers (FT-FM2) are sold as a set. Please refer to p.93~ for details.
4)
Sold as a set comprising vacuum-resistant type fi ber + photo-terminal (FV-BR1) + fi ber at atmospheric side (FT-J8). Please refer to p.91~ for details.
Thru-beam type (one pair set)
Fibers are listed in alphabetic order. Refer to p.63~ “Fiber Selection” for details of each fi ber.
LIST OF FIBERS
Model No. Sensing range (mm in) (Note 1)
Dimensions
Standard type FX-101□
Long sensing range type FX-102□
FT-PS1 40 1.575 90 3.543 P.109
FT-R80 180 7.087 430 16.929 P.109
FT-SFM2 300 11.811 800 31.496 P.109
FT-SFM2L 760 29.921 2,400 94.488 P.109
FT-SFM2SV2 180 7.087 470 18.504 P.109
FT-SNFM2 130 5.118 280 11.024 P.109
FT-T80 300 11.811 800 31.496 P.109
FT-V10 1,000 39.370 2,350 92.520 P.109
FT-V22 140 5.512 380 14.961 P.109
FT-V41 40 1.575 120 4.724 P.109
FT-V80Y 340 13.386 800 31.496 P.109
FT-W4 80 3.150 220 8.661 P.109
FT-W8 260 10.236 650 25.591 P.110
FT-WA8 1,500 59.055
3,500 137.795 (Note 2)
P.110
FT-WA30
3,500 137.795 (Note 2) 3,500 137.795 (Note 2)
P.110
FT-WKV8 700 27.559 2,200 86.614 P.110
FT-WR80 215 8.465 570 22.441 P.110
FT-WR80L 430 16.929 1,150 45.276 P.110
FT-WS3 150 5.906 600 23.622 P.110
FT-WS4 80 3.150 220 8.661 P.110
FT-WS8 260 10.236 650 25.591 P.110
FT-WS8L 600 23.622 1,500 59.055 P.110
FT-WV42 30 1.181 80 3.150 P.110
FT-WZ4 230 9.055 670 26.378 P.110
FT-WZ4HB 80 3.150 230 9.055 P.111
FT-WZ7 330 12.992 1,000 39.370 P.111
FT-WZ7HB 190 7.480 580 22.835 P.111
FT-WZ8 330 12.992 950 37.402 P.111
FT-WZ8E 700 27.559 2,100 82.677 P.111
FT-WZ8H 1,200 47.244 2,800 110.236 P.111
FT-Z8 360 14.173 1,000 39.370 P.111
FT-Z8E 800 31.496 1,850 72.835 P.111
FT-Z8H 1,400 55.118 3,100 122.047 P.111
FT-Z802Y 520 20.472 3,100 122.047 P.111
Digital Fiber Sensor FX-100 SERIES
128
FIBER
SENSORS
LASER
SENSORS
PHOTO-
ELECTRIC
SENSORS
MICRO
PHOTO-
ELECTRIC
SENSORS
AREA
SENSORS
SAFETY
COMPONENTS
PRESSURE
SENSORS
INDUCTIVE
PROXIMITY
SENSORS
PARTICULAR
USE
SENSORS
SENSOR
OPTIONS
WIRE-
SAVING
SYSTEMS
MEASURE-
MENT
SENSORS
STATIC
CONTROL
DEVICES
LASER
MARKERS
Selection
Guide
Fiber Sensor
Amplifiers
FX-300
FX-100
Fibers
FT / FD / FR
FX-410
FX-311
FX-11A
FX-301-F
Other
Products
FIBER
SENSORS
FX-100
Fiber Sensor
Amplifi ers
LIST OF FIBERS
Fibers are listed in alphabetic order. Refer to p.63~ “Fiber Selection” for details of each fi ber.
Retrorefl ective type
Model No. Sensing range (mm in) (Note 1, 2) Dimensions
Standard type FX-101□
Long sensing range type FX-102□
FR-KV1 15 to 200 0.591 to 7.874 15 to 360 0.591 to 14.173 P.112
FR-KZ21 200 7.874 200 7.874 P.112
FR-KZ21E 200 7.874 200 7.874 P.112
FR-WKZ11 100 to 550 3.937 to 21.654 100 to 830 3.937 to 32.677 P.112
2)
The sensing range of FR-WKZ11 is the possible setting range for the refl ector or refl ective tape. The fi ber can detect an object less than 100 mm 3.937 in away.
However, note that if there are any white or highly-refl ective surfaces near the fi ber head, refl ected incident light may affect the fi ber head. If this occurs,
adjust the threshold value of the amplifi er unit before use.
The sensing range of FR-KZ21(E) is the possible setting range for the refl ector. However, if setting the fi ber to detect objects passing within 0 to 20 mm
0 to 0.787 in from the fi ber head, unstable detection may result.
The sensing range of FR-KV1 is the possible setting range for the refl ector. The fi ber can detect an object less than 15 mm 0.591 in away.
Refl ective type
Fibers are listed in alphabetic order. Refer to “Fiber Selection p.63~” for details of each fi ber.
Model No. Sensing range (mm in) (Note 1, 2)
Dimensions
Standard type FX-101□
Long sensing range type FX-102□
FD-A15 125 4.921 250 9.843 P.113
FD-AFM2 105 4.134 285 11.220 P.113
FD-AFM2E 85 3.346 245 9.646 P.113
FD-B8 170 6.693 440 17.323 P.113
FD-E12 3.5 0.138 13 0.512 P.113
FD-E22 16 0.630 45 1.772 P.113
FD-EG1 18 0.709 50 1.969 P.113
FD-EG2 10 0.394 30 1.181 P.113
FD-EG3 7 0.276 22 0.866 P.113
FD-EN500S1 1 0.039 4 0.157 P.113
FD-ENM1S1 15 0.591 48 1.890 P.114
FD-F4
Applicable pipe diameter:
Outer dia. ø6 to ø26 mm ø0.236 to
ø1.024 in transparent pipe
[PFA (fl uorine resin) or equivalently
transparent pipe, wall thickness 1 mm
0.039 in]
P.114
FD-F41
Applicable pipe diameter:
Outer dia. ø6 to ø26 mm ø0.236 to
ø1.024 in transparent pipe
[PVC (vinyl chloride), fl uorine resin,
polycarbonate, acrylic, glass, wall
thickness 1 to 3 mm 0.039 to 0.118 in]
P.114
FD-F8Y
–
P.114
FD-FM2 100 3.937 410 16.142 P.114
FD-FM2S 100 3.937 345 13.583
P.114
FD-FM2S4 P.114
FD-G4 50 1.969 120 4.724 P.114
Model No. Sensing range (mm in) (Note 1, 2)
Dimensions
Standard type FX-101□
Long sensing range type FX-102□
FD-G6 50 1.969 120 4.724 P.114
FD-G6X 45 1.772 160 6.299 P.114
FD-H13-FM2 100 3.937 280 11.024 P.114
FD-H18-L31 0 to 10 0 to 0.394 0 to 25 0 to 0.984 P.115
FD-H20-21 90 3.543 280 11.024 P.115
FD-H20-M1 120 4.724 300 11.811 P.115
FD-H30-KZ1V-S (Note 3)
25 to 80 0.984 to 3.150
10 to 220 0.394 to 8.661
P.115
FD-H30-L32
2 to 9 0.079 to 0.354
0 to 17 0 to 0.669 P.115
FD-H30-L32V-S (Note 3)
2.5 to 6.5 0.098 to 0.256
0 to 11 0 to 0.433 P.115
FD-H35-20S 85 3.346 200 7.874 P.116
FD-H35-M2 75 2.953 280 11.024
P.116
FD-H35-M2S6 P.116
FD-L4
5 to 8 0.197 to 0.315
(Convergent point 6 0.236)
1 to 17 0.039 to 0.669
(Convergent point 6 0.236)
P.116
FD-L41
3 to 14 0.118 to 0.551
(Convergent point 8 0.315)
1.5 to 16 0.059 to 0.630
(Convergent point 8 0.315)
P.116
FD-L43 0 to 19 0 to 0.748 0 to 25 0 to 0.984 P.116
FD-L44 0 to 6 0 to 0.236 0 to 8 0 to 0.315 P.116
FD-L44S 0 to 4.5 0 to 0.177 0 to 5.5 0 to 0.217 P.116
FD-L45 0 to 40 0 to 1.575 0 to 50 0 to 1.969 P.116
FD-L46
16 to 30 0.630 to 1.181 12 to 50 0.472 to 1.969
P.116
FD-NFM2
35 1.378 100 3.937
P.117
FD-NFM2S P.117
FD-NFM2S4 P.117
FD-P2 25 0.984 65 2.559 P.117
Notes: 1) The standard sensing objects of the sensing ranges vary depending on the fi bers. Refer to p.71~ for details.
2) Please take care that the sensing range of the free-cut type fi ber may be reduced by 20 % max. depending upon how the fi ber is cut.
3) Sold as a set comprising vacuum-resistant type fi ber + photo-terminal (FV-BR1) + fi ber at atmospheric side (FT-J8). Please refer to p.91~ for details.
Notes: 1) Please take care that the sensing range of the free-cut type fi ber may be reduced by 20 % max. depending upon how the fi ber is cut.
The sensing range of FR-WKZ11 is specifi ed for the RF-13. The sensing range of FR-KZ21, FR-KZ21E and FR-KV1 is specifi ed for the attached refl ector.
The sensing ranges when using in combination with the FR-WKZ11 refl ector (optional) are given in the below table.
Amplifi er
Refl ector FX-101□FX-102□
FR-WKZ11 + RF-210
100 to 700 3.937 to 27.559 100 to 1,100 3.937 to 43.307
FR-WKZ11 + RF-220
100 to 1,300 3.937 to 51.181 100 to 2,600 3.937 to 102.362
FR-WKZ11 + RF-230
100 to 2,000 3.937 to 78.740 100 to 4,000 3.937 to 157.480
129
Digital Fiber Sensor FX-100 SERIES
FIBER
SENSORS
LASER
SENSORS
PHOTO-
ELECTRIC
SENSORS
MICRO
PHOTO-
ELECTRIC
SENSORS
AREA
SENSORS
SAFETY
COMPONENTS
PRESSURE
SENSORS
INDUCTIVE
PROXIMITY
SENSORS
PARTICULAR
USE
SENSORS
SENSOR
OPTIONS
WIRE-
SAVING
SYSTEMS
MEASURE-
MENT
SENSORS
STATIC
CONTROL
DEVICES
LASER
MARKERS
Selection
Guide
Fiber Sensor
Amplifiers
FX-300
FX-100
Fibers
FT / FD / FR
FX-410
FX-311
FX-11A
FX-301-F
Other
Products
FIBER
SENSORS
FX-100
Fiber sensor
Ampilifi ers
LIST OF FIBERS
Model No. Sensing range (mm in) (Note 1, 2)
Dimensions
Standard type FX-101□
Long sensing range type FX-102□
FD-P40 8 0.315 30 1.181 P.117
FD-P50 45 1.772 150 5.906 P.117
FD-P60 45 1.772 150 5.906 P.117
FD-P80 90 3.543 200 7.874 P.117
FD-P81X 70 2.756 220 8.661 P.117
FD-R80 70 2.756 180 7.087 P.117
FD-S80 100 3.937 345 13.583 P.117
FD-SFM2SV2 30 1.181 90 3.543 P.117
FD-SNFM2 35 1.378 100 3.937 P.118
FD-T40 35 1.378 100 3.937 P.118
FD-T80 100 3.937 345 13.583 P.118
FD-V41 25 0.984 70 2.756 P.118
FD-W8 80 3.150 230 9.055 P.118
FD-W44 15 0.591 40 1.575 P.118
Refl ective type
Fibers are listed in alphabetic order. Refer to “Fiber Selection p.63~” for details of each fi ber.
Model No. Sensing range (mm in) (Note 1, 2)
Dimensions
Standard type FX-101□
Long sensing range type FX-102□
FD-WG4 28 1.102 75 2.953 P.118
FD-WKZ1
20 to 180 0.787 to 7.087
20 to 480 0.787 to 18.898
P.118
FD-WL41
7 to 12 0.276 to 0.472
(Convergent point 8 0.315)
6 to 13.5 0.236 to 0.531
(Convergent point 8 0.315)
P.118
FD-WL48
1 to 4.5 0.039 to 0.177
0.5 to 6.5 0.020 to 0.256
P.119
FD-WS8 80 3.150 230 9.055 P.119
FD-WSG4 28 1.102 75 2.953 P.119
FD-WT4 15 0.591 40 1.575 P.119
FD-WT8 80 3.150 230 9.055 P.119
FD-WV42 6 0.236 20 0.787 P.119
FD-WZ4
2 to 20 0.079 to 0.787 1 to 70 0.039 to 2.756
P.119
FD-WZ4HB P.119
FD-WZ7
1 to 55 0.039 to 2.165
160 6.299 P.119
FD-WZ7HB
1 to 60 0.039 to 2.362
0.5 to 180 0.020 to 7.087
P.119
Notes: 1) The standard sensing objects of the sensing ranges vary depending on the fi bers. Refer to p.71~ for details.
2) Please take care that the sensing range of the free-cut type fi ber may be reduced by 20 % max. depending upon how the fi ber is cut.
3) Sold as a set comprising vacuum-resistant type fi ber + photo-terminal (FV-BR1) + fi ber at atmospheric side (FT-J8). Please refer to p.91~ for details.
Digital Fiber Sensor FX-100 SERIES
130
FIBER
SENSORS
LASER
SENSORS
PHOTO-
ELECTRIC
SENSORS
MICRO
PHOTO-
ELECTRIC
SENSORS
AREA
SENSORS
SAFETY
COMPONENTS
PRESSURE
SENSORS
INDUCTIVE
PROXIMITY
SENSORS
PARTICULAR
USE
SENSORS
SENSOR
OPTIONS
WIRE-
SAVING
SYSTEMS
MEASURE-
MENT
SENSORS
STATIC
CONTROL
DEVICES
LASER
MARKERS
Selection
Guide
Fiber Sensor
Amplifiers
FX-300
FX-100
Fibers
FT / FD / FR
FX-410
FX-311
FX-11A
FX-301-F
Other
Products
FIBER
SENSORS
FX-100
Fiber Sensor
Amplifi ers
Lens (For thru-beam type fi ber)
Designation Model No. Description
For thru-beam type fi ber
Expansion
lens
(Note 1)
FX-LE1
Increases the sensing
range by 5 times or more.
• Ambient temperature:
–60 to +350 °C
–76 to +662 °F
(Note 3)
Sensing range (mm in) [Lens on both sides]
Amplifi er
Fiber FX-101□FX-102□
FT-B8 2,200 86.614
3,500 137.795 (Note 2)
FT-FM2, FT-T80 3,000 118.110
3,500 137.795 (Note 2)
FT-R80 1,900 74.803
3,500 137.795 (Note 2)
FT-W8 3,000 118.110
3,500 137.795 (Note 2)
FT-P80, FT-P60
3,500 137.795 (Note 2) 3,500 137.795 (Note 2)
FT-P81X 1,600 62.992 (Note 2) 1,600 62.992 (Note 2)
FT-H35-M2 2,000 78.740
3,500 137.795 (Note 2)
FT-H20W-M1 1,300 51.181 1,600 62.992 (Note 2)
FT-H20-M1 1,600 62.992 (Note 2) 1,600 62.992 (Note 2)
FT-H20-J20-S, FT-H20-J30-S, FT-H20-J50-S
1,000 39.370
3,500 137.795 (Note 2)
Super-
expansion
lens
(Note 1)
FX-LE2
Tremendously increases the
sensing range with large
diameter lenses.
• Ambient temperature:
–60 to +350 °C
–76 to +662 °F
(Note 3)
Sensing range (mm in) [Lens on both sides]
Amplifi er
Fiber FX-101□FX-102□
FT-B8, FT-FM2, FT-R80, FT-W8, FT-P80, FT-P60
3,500 137.795 (Note 2) 3,500 137.795 (Note 2)
FT-P81X 1,600 62.992 (Note 2) 1,600 62.992 (Note 2)
FT-H35-M2
3,500 137.795 (Note 2) 3,500 137.795 (Note 2)
FT-H20W-M1, FT-H20-M1
1,600 62.992 (Note 2) 1,600 62.992 (Note 2)
FT-H13-FM2
3,500 137.795 (Note 2) 3,500 137.795 (Note 2)
FT-H20-J20-S, FT-H20-J30-S, FT-H20-J50-S
3,500 137.795 (Note 2) 3,500 137.795 (Note 2)
Side-view
lens FX-SV1
Beam axis is bent by 90°.
• Ambient temperature:
–60 to +300 °C
–76 to +572 °F
(Note 3)
Sensing range (mm in) [Lens on both sides]
Amplifi er
Fiber FX-101□FX-102□
FT-B8 530 20.866 1,450 57.087
FT-FM2, FT-T80 550 21.654 1,700 66.929
FT-W8 450 17.717 1,300 51.181
FT-P80 420 16.535 1,400 55.118
FT-P60 300 11.811 850 33.465
FT-P81X 550 21.654 1,700 66.929
FT-H35-M2 280 11.024 800 31.496
FT-H20W-M1 140 5.512 400 15.748
FT-H20-M1 280 11.024 840 33.071
FT-H20-J20-S, FT-H20-J30-S, FT-H20-J50-S
150 5.906 410 16.142
Expansion
lens for vacuum-
resistant fi ber
(Note 1)
FV-LE1
Sensing range increases by
4 times or more.
• Ambient temperature:
–60 to +350 °C –76 to +662 °F
(Note 3)
Sensing range (mm in) [Lens on both sides] (Note 4)
Amplifi er
Fiber FX-101□FX-102□
FT-H30-M1V 450 17.717 1,600 62.992
Side-view
lens for
vacuum-
resistant fi ber
FV-SV2
Beam axis is bent by 90°.
• Ambient temperature:
–60 to +300 °C –76 to +572 °F
(Note 3)
Sensing range (mm in) [Lens on both sides] (Note 4)
Amplifi er
Fiber FX-101□FX-102□
FT-H30-M1V 450 17.717 1,600 62.992
Notes: 1) Be careful when installing the thru-beam type fi ber equipped with the expansion lens, as the beam envelope becomes narrow and alignment is diffi cult.
Especially when installing a fi ber with many cores (sharp bending fi bers and heat-resistant glass fi ber), please be sure to use it only after you have
adjusted it suffi ciently.
2) The fi ber cable length practically limits the sensing range to 3,500 mm 137.795 in long (FT-H20W-M1, FT-P81X and FT-H20-M1: 1,600 mm 62.992 in).
3) For details on the ambient temperatures for the fi bers which being combined, refer to p.101~.
4) The fi ber cable length for the FT-H30-M1V is 1 m 3.281 ft. The sensing ranges in FX-102□ (long sensing range type) take into account the length of the
FT-J8 atmospheric side fi ber.
FIBER OPTIONS
The dimensions are on p.120~.
131
Digital Fiber Sensor FX-100 SERIES
FIBER
SENSORS
LASER
SENSORS
PHOTO-
ELECTRIC
SENSORS
MICRO
PHOTO-
ELECTRIC
SENSORS
AREA
SENSORS
SAFETY
COMPONENTS
PRESSURE
SENSORS
INDUCTIVE
PROXIMITY
SENSORS
PARTICULAR
USE
SENSORS
SENSOR
OPTIONS
WIRE-
SAVING
SYSTEMS
MEASURE-
MENT
SENSORS
STATIC
CONTROL
DEVICES
LASER
MARKERS
Selection
Guide
Fiber Sensor
Amplifiers
FX-300
FX-100
Fibers
FT / FD / FR
FX-410
FX-311
FX-11A
FX-301-F
Other
Products
FIBER
SENSORS
FX-100
Fiber sensor
Ampilifi ers
Lens (For refl ective type fi ber)
Designation Model No. Description
For refl ective type fi ber
Pinpoint spot
lens
FX-MR1
Pinpoint spot of ø0.5 mm ø0.020 in. Enables detection of minute objects or small marks.
• Distance to focal point: 6 ± 1 mm 0.236 ± 0.039 in • Applicable fi bers: FD-WG4, FD-G4
• Ambient temperature: –40 to +70 °C –40 to +158 °F (Note 2)
Zoom lens FX-MR2
Screw-in
depth
Distance to
focal point Spot
diameter
The spot diameter is adjustable from ø0.7 to
ø2 mm ø0.028 to ø0.079 in according to how
much the fi ber is screwed in.
• Applicable fi bers: FD-WG4, FD-G4
• Ambient temperature: –40 to +70 °C
–40 to +158 °F (Note 2)
• Accessory: MS-EX-3 (mounting bracket)
Sensing range for FX-101□ (mm in) (Note 1)
Screw-in depth
Distance to focal point
Spot diameter
7 mm 0.276 in
18.5 0.728
approx. ø0.7 ø0.028
12 mm 0.472 in
27 1.063
approx. ø1.2 ø0.047
14 mm 0.551 in
43 1.693
approx. ø2.0 ø0.079
Finest spot
lens FX-MR3
Distance to
focal point
Spot diameter
Extremely fi ne spot of ø0.3 mm ø0.012 in
approx. achieved.
• Applicable fi bers: FD-WG4, FD-G4, FD-EG1,
FD-EG2, FD-EG3, FD-G6X, FD-G6
• Ambient temperature: –40 to +70 °C
–40 to +158 °F (Note 2)
Sensing range for FX-101□ (mm in) (Note 1)
Fiber model No.
Distance to focal point
Spot diameter
FD-EG3
7.5 ± 0.5
0.295 ± 0.020
ø0.15 ø0.006
approx.
FD-EG2
7.5 ± 0.5
0.295 ± 0.020
ø0.2 ø0.008
approx.
FD-EG1
7.5 ± 0.5
0.295 ± 0.020
ø0.3 ø0.012
approx.
FD-WG4/G4,
FD-G6X/G6
7.5 ± 0.5
0.295 ± 0.020
ø0.5 ø0.020
approx.
Finest spot
lens FX-MR6
Extremely fi ne spot of ø0.1 mm ø0.004 in
approx. achieved.
• Applicable fi bers: FD-WG4, FD-G4, FD-EG1,
FD-EG2, FD-EG3, FD-G6X, FD-G6
• Ambient temperature: –20 to +60 °C
–4 to +140 °F (Note 2)
Sensing range for FX-101□ (mm in) (Note 1)
Fiber model No.
Distance to focal point
Spot diameter
FD-EG3
7 ± 0.5
0.276 ± 0.020
ø0.1 ø0.004
approx.
FD-EG2
7 ± 0.5
0.276 ± 0.020
ø0.15 ø0.006
approx.
FD-EG1
7 ± 0.5
0.276 ± 0.020
ø0.2 ø0.008
approx.
FD-WG4/G4,
FD-G6X/G6
7 ± 0.5
0.276 ± 0.020
ø0.4 ø0.016
approx.
Zoom lens
Side-view
type
FX-MR5
FX-MR2 is converted into a side-view type
and can be mounted in a very small space.
• Applicable fi bers: FD-WG4, FD-G4
• Ambient temperature: –40 to +70 °C
–40 to +158 °F (Note 2)
Sensing range for FX-101□ (mm in) (Note 1)
Screw-in depth
Distance to focal point
Spot diameter
8 mm 0.315 in
13 0.512
approx. ø0.5 ø0.020
10 mm 0.394 in
15 0.591
approx. ø0.8 ø0.031
14 mm 0.551 in
30 1.181
approx. ø3.0 ø0.118
Screw-in
depth
Spot diameter
Distance
to focal
point
Screw-in
depth
Spot diameter
Distance
to focal
point
Notes: 1) The sensing ranges are the values when used in combination with FX-101□ (standard type). Please contact our offi ce for details on sensing ranges for
other types of amplifi er.
2) For details on the ambient temperatures for the fi bers which being combined, refer to p.101~.
FIBER OPTIONS
The dimensions are on p.121~.
Digital Fiber Sensor FX-100 SERIES
132
FIBER
SENSORS
LASER
SENSORS
PHOTO-
ELECTRIC
SENSORS
MICRO
PHOTO-
ELECTRIC
SENSORS
AREA
SENSORS
SAFETY
COMPONENTS
PRESSURE
SENSORS
INDUCTIVE
PROXIMITY
SENSORS
PARTICULAR
USE
SENSORS
SENSOR
OPTIONS
WIRE-
SAVING
SYSTEMS
MEASURE-
MENT
SENSORS
STATIC
CONTROL
DEVICES
LASER
MARKERS
Selection
Guide
Fiber Sensor
Amplifiers
FX-300
FX-100
Fibers
FT / FD / FR
FX-410
FX-311
FX-11A
FX-301-F
Other
Products
FIBER
SENSORS
FX-100
Fiber Sensor
Amplifi ers
SPECIFICATIONS
Notes: 1) Where measurement conditions have not been specifi ed precisely, the conditions used were an ambient temperature of +23 °C +73.4 °F.
2) When using the interference prevention function, set the emission frequencies for the amplifi ers to be covered by the interference prevention function to
different frequency values.
However, the interference prevention function does not operate at emission frequency 0 (factory default setting) for the FX-101(P)(-Z) / FX-101(P)-CC2.
3) The voltage withstandability and the insulation resistance values given in the above table are for the amplifi er only.
4) Connector attached cable CN-14A-C2 is not attached to the models that have no “-CC2” at the end of the model Nos.
Make sure to use the optional connector attached cable CN-14A(-R)-C□ or the connector CN-14A, or a connector manufactured by J.S.T. Mfg., Ltd.
(contact: SPHD-001T-P0.5, housing: PAP-04V-S).
Model Nos. having the suffi x “-Z” are M8 plug-in connector type. Make sure to use the optional M8 attached connector cable CN-24A-C□.
Type Standard type Long sensing range type
Cable set Cable set
Model No.
NPN output FX-101(-Z) (Note 4) FX-101-CC2 FX-102(-Z) (Note 4) FX-102-CC2
Item PNP output FX-101P(-Z) (Note 4) FX-101P-CC2 FX-102P(-Z) (Note 4) FX-102P-CC2
Supply voltage 12 to 24 V DC ± 10 % Ripple P-P 10 % or less
Power consumption Normal operation: 720 mW or less (Current consumption 30 mA or less at 24 V supply voltage)
ECO mode: 600 mW or less (Current consumption 25 mA or less at 24 V supply voltage)
Output
<NPN output type>
NPN open-collector transistor
• Maximum sink current: 100 mA
•
Applied voltage: 30 V DC or less (between output and 0 V)
• Residual voltage: 1.5 V or less (at 100 mA sink current)
<PNP output type>
PNP open-collector transistor
• Maximum source current: 100 mA
•
Applied voltage: 30 V DC or less (between output and +V)
•
Residual voltage: 1.5 V or less (at 100 mA source current)
Output operation Selectable either Light-ON or Dark-ON, at SET mode
Short-circuit protection Incorporated
External input
<NPN output type>
NPN non-contact input
• Signal condition
High: +8 V to +V DC or Open
Low: 0 to +2 V DC
(Source current 0.5 mA or less)
• Input impedance: 10 kΩ approx.
<PNP output type>
PNP non-contact input
• Signal condition
High: +4 V to +V DC
(Sink current 0.5 to 3 mA)
Low: 0 to +0.6 V DC or Open
• Input impedance: 10 kΩ approx.
Response time
Emission frequency 0: 250 μs or less (factory default setting)
Emission frequency 1: 450 μs or less
Emission frequency 2: 500 μs or less
Emission frequency 3: 600 μs or less
Emission frequency 1: 2.5 ms or less (factory default setting)
Emission frequency 2: 2.8 ms or less
Emission frequency 3: 3.2 ms or less
Emission frequency 4: 5.0 ms or less
Sensitivity setting 2-level teaching / Limit teaching / Full-auto teaching
Operation indicator Orange LED (lights up when the output is ON)
Digital display 4 digits (green) + 4 digits (red) LCD display
Fine sensitivity adjustment function
Incorporated
Timer function ON-delay / OFF-delay timer, switchable either effective or ineffective
[Timer period: 1 ms, 5 ms, 10 ms, 20 ms, 40 ms, 50 ms, 100 ms, 500 ms, 1,000 ms]
Attenuation function Incorporated
Switchable either effective or ineffective
Interference prevention
function
Incorporated
Emission frequency selection method (Note 2)
(Functions at emission frequency 1, 2 or 3)
Incorporated
Emission frequency selection method (Note 2)
(Functions at emission frequency 1, 2, 3 or 4)
Environmental resistance
Ambient temperature
–10 to +55 °C +14 to +131 °F (If 4 to 7 units are mounted close together: –10 to +50 °C +14 to +122 °F, if 8 to 16 units are mounted close together:
–10 to +45 °C +14 to +113 °F) (No dew condensation or icing allowed), Storage: –20 to +70 °C –4 to +158 °F
Ambient humidity 35 to 85 % RH, Storage: 35 to 85 % RH
Ambient illuminance Incandescent light: 3,000 ℓx at the light-receiving face
Voltage withstandability 1,000 V AC for one min. between all supply terminals connected together and enclosure (Note 3)
Insulation resistance 20 MΩ, or more, with 250 V DC megger between all supply terminals connected together and enclosure (Note 3)
Vibration resistance 10 to 150 Hz frequency, 0.75 mm 0.030 in amplitude in X, Y and Z directions for two hours each
Shock resistance 98 m/s2 acceleration (10 G approx.) in X, Y and Z directions for fi ve times each
Emitting element (modulated) Red LED (Peak emission wavelength: 632 nm 0.025 mil)
Material Enclosure: Polycarbonate, Key switch: Polycarbonate, Fiber lock lever: PBT
Connecting method Connector (Note 4)
Cable length Total length up to 100 m 328.084 ft is possible with 0.3 mm2, or more, cable.
Weight Net weight: 15 g approx.
Gross weight: 35 g approx.
Net weight: 15 g approx.
Gross weight: 75 g approx.
Net weight: 15 g approx.
Gross weight: 35 g approx.
Net weight: 15 g approx.
Gross weight: 75 g approx.
Accessory
–
CN-14A-C2
(Connector attached cable, 2 m 6.562 ft long): 1pc.
–
CN-14A-C2
(Connector attached cable, 2 m 6.562 ft long): 1pc.
Refer to p.101~ for fi ber specifi cations.
133
Digital Fiber Sensor FX-100 SERIES
FIBER
SENSORS
LASER
SENSORS
PHOTO-
ELECTRIC
SENSORS
MICRO
PHOTO-
ELECTRIC
SENSORS
AREA
SENSORS
SAFETY
COMPONENTS
PRESSURE
SENSORS
INDUCTIVE
PROXIMITY
SENSORS
PARTICULAR
USE
SENSORS
SENSOR
OPTIONS
WIRE-
SAVING
SYSTEMS
MEASURE-
MENT
SENSORS
STATIC
CONTROL
DEVICES
LASER
MARKERS
Selection
Guide
Fiber Sensor
Amplifiers
FX-300
FX-100
Fibers
FT / FD / FR
FX-410
FX-311
FX-11A
FX-301-F
Other
Products
FIBER
SENSORS
FX-100
Fiber sensor
Ampilifi ers
I/O CIRCUIT AND WIRING DIAGRAMS
FX-10□(-Z/-CC2)NPN output type
Users’ circuitInternal circuit
+
–
12 to 24 V DC
±
10 %
100 mA max.
* 1
D
Tr
Load
(Brown) +V
(Blue) 0 V
(White) Extemal input
(Black) Output
Terminal No.
Color code of cable with connector
ZD
+8 V
Sensor circuit
1
2
3
4
I/O circuit diagram
12
34
Terminal arrangement diagram
Connector type
Terminal No.
Function
1
+V
2
Output
3
External input
4
0 V
M8 plug-in connector type
Terminal No.
Function
1
+V
2
Output
3
External input
4
0 V
1
2
3
4
Symbols … D : Reverse supply polarity protection diode
ZD: Surge absorption zener diode
Tr : NPN output transistor
Non-voltage contact or NPN open-collector transistor
or
High (+8 V to +V DC, or open): Ineffective
Low [(0 to +2 V DC (source current 0.5 mA or less)]: Effective
1*
FX-10□P(-Z/-CC2)PNP output type
I/O circuit diagram
Users’ circuitInternal circuit
12 to 24 V DC
± 10 %
100 mA max.
* 1
tiucric rosne
S
D
Tr
ZD
Load
+
–
(Brown) +V
(Blue) 0 V
(White) External input
(Black) Output
Terminal No.
Color code of cable with connector
2
3
4
12
34
Terminal arrangement diagram
Connector type
Terminal No.
Function
1
+V
2
Output
3
External input
4
0 V
M8 plug-in connector type
Terminal No.
Function
1
+V
2
Output
3
External input
4
0 V
1
2
3
4
Non-voltage contact or PNP open-collector transistor
or
High [ +4 V to +V DC (sink current 0.5 to 3 mA)]: Effective
Low (0 to +0.6 V DC, or open): Ineffective
1*
Symbols … D : Reverse supply polarity protection diode
ZD: Surge absorption zener diode
Tr : PNP output transistor
Digital Fiber Sensor FX-100 SERIES
134
FIBER
SENSORS
LASER
SENSORS
PHOTO-
ELECTRIC
SENSORS
MICRO
PHOTO-
ELECTRIC
SENSORS
AREA
SENSORS
SAFETY
COMPONENTS
PRESSURE
SENSORS
INDUCTIVE
PROXIMITY
SENSORS
PARTICULAR
USE
SENSORS
SENSOR
OPTIONS
WIRE-
SAVING
SYSTEMS
MEASURE-
MENT
SENSORS
STATIC
CONTROL
DEVICES
LASER
MARKERS
Selection
Guide
Fiber Sensor
Amplifiers
FX-300
FX-100
Fibers
FT / FD / FR
FX-410
FX-311
FX-11A
FX-301-F
Other
Products
FIBER
SENSORS
FX-100
Fiber Sensor
Amplifi ers
SENSING CHARACTERISTICS (TYPICAL)
1,000
39.37
2,000
78.74
3,000
118.11
4,000
157.48
0
200
7.874
100
3.937
0 100
3.937
200
7.874
FX-102
FX-101
Setting distance L (mm in)
Operating point ℓ (mm in)
CenterDown Up
ℓ
8 mm 0.315 in
approx.
Fiber head
Fiber
head
L
0
Operating point ℓ (mm in)
CenterLeft Right
200
7.874
100
3.937
0 100
3.937
200
7.874
1,000
39.37
2,000
78.74
3,000
118.11
4,000
157.48
FX-102
FX-101
ℓ
Fiber
head
Fiber
head
L
Setting distance L (mm in)
1,000
39.370
500
19.685
0
1,000
39.37
500
19.685
0 500
19.685
1,000
39.37
FX-102
Operating point ℓ (mm in)
CenterLeft Right
ℓ
Fiber
head
Fiber
head
L
Setting distance L (mm in)
FX-101
400
15.748
200
7.874
0 200
7.874
400
15.748
Operating point ℓ (mm in)
CenterLeft Right
1,000
39.370
500
19.685
0
FX-101
FX-102
ℓ
Fiber
head
Fiber
head
L
Setting distance L (mm in)
Thru-beam type
FT-A8 Thru-beam type
FT-B8
Thru-beam
type
FT-FM2 FT-FM2S FT-FM2S4
FT-SFM2 FT-T80
Parallel deviation
Vertical direction•Horizontal direction• Parallel deviation Parallel deviation
100
3.937
50
1.969
050
1.969
100
3.937
0
Operating point ℓ (mm in)
CenterLeft Right
400
15.748
200
7.874
FX-102
FX-101
L
ℓ
White non-glossy paper
Fiber
head
Setting distance L (mm in)
100
3.937
50
1.969
050
1.969
100
3.937
200
7.874
400
15.748
0
Operating point ℓ (mm in)
CenterLeft Right
FX-102
FX-101
L
ℓ
White non-glossy paper
Fiber
head
Setting distance L (mm in)
40
1.575
20
0.787
020
0.787
40
1.575
50
1.969
100
3.937
0
Operating point ℓ (mm in)
CenterLeft Right
FX-102
FX-101
L
ℓ
White non-glossy paper
Fiber
head
Setting distance L (mm in)
40
1.575
20
0.787
020
0.787
40
1.575
0
Operating point ℓ (mm in)
CenterLeft Right
50
1.969
100
3.937
150
5.906
200
7.874
FX-102
FX-101
L
ℓ
White non-glossy paper
Fiber
head
Setting distance L (mm in)
Refl ective type
FD-G4 Refl ective type
FD-G6X
Refl ective type
FD-B8 Refl ective type
FD-FM2
Sensing fi eld Sensing fi eld Sensing fi eld Sensing fi eld
200
7.874
100
3.937
100
3.937
200
7.874
100
3.937
200
7.874
300
11.811
400
15.748
0
FX-102
FX-101
Operating point ℓ (mm in)
CenterLeft Right
ℓ
Fiber
head
Fiber
head
L
Setting distance L (mm in)
400
15.748
200
7.874
0 200
7.874
400
15.748
Operating point ℓ (mm in)
CenterLeft Right
1,000
39.370
500
19.685
0
FX-102
FX-101
ℓ
Fiber
head
Fiber
head
L
Setting distance L (mm in)
100
3.937
50
1.969
050
1.969
100
3.937
Operating point ℓ (mm in)
CenterLeft Right
200
7.874
100
3.937
0
FX-102
FX-101
ℓ
Fiber
head
Fiber
head
L
Setting distance L (mm in)
200
7.874
100
3.937
0 100
3.937
200
7.874
200
7.874
400
15.748
600
23.622
800
9.843
0
FX-102
FX-101
Operating point ℓ (mm in)
CenterLeft Right
ℓ
Fiber
head
Fiber
head
L
Setting distance L (mm in)
Thru-beam type
FT-W4 FT-WS4
Thru-beam type
FT-W8 FT-WS8
Thru-beam
type
FT-NFM2 FT-NFM2S
FT-NFM2S4 FT-SNFM2
Thru-beam type
FT-P81X
Parallel deviation Parallel deviation Parallel deviation Parallel deviation
Operating point ℓ (mm in)
CenterLeft Right
100
3.937
50
1.969
0
20
0.787
10
0.394
010
0.394
20
0.787
FX-101
FX-102
L
ℓ
White non-glossy paper
Fiber
head
Setting distance L (mm in)
Operating point ℓ (mm in)
CenterLeft Right
200
7.874
100
3.937
0
40
1.575
20
0.787
020
0.787
40
1.575
FX-101
FX-102
L
ℓ
White non-glossy paper
Fiber
head
Setting distance L (mm in)
40
1.575
20
0.787
020
0.787
40
1.575
Operating point ℓ (mm in)
CenterLeft Right
200
7.874
100
3.937
0
FX-101
FX-102
L
ℓ
White non-glossy paper
Fiber
head
Setting distance L (mm in)
Operating point ℓ (mm in)
CenterLeft Right
20
0.787
10
0.394
010
0.394
20
0.787
0
FX-102
FX-101
20
0.787
40
1.575
60
2.362
80
3.150
L
ℓ
White non-glossy paper
Fiber
head
Setting distance L (mm in)
Sensing fi eld Sensing fi eld Sensing fi eld Sensing fi eld
Refl ective type
FD-W8 FD-WS8 FD-WT8
Refl ective type
FD-WG4 FD-WSG4
Refl ective
type
FD-NFM2 FD-NFM2S FD-NFM2S4
FD-SNFM2 FD-T40
Refl ective type
FD-P81X
Contact our offi ce for sensing characteristics that are not contained here.
135
Digital Fiber Sensor FX-100 SERIES
FIBER
SENSORS
LASER
SENSORS
PHOTO-
ELECTRIC
SENSORS
MICRO
PHOTO-
ELECTRIC
SENSORS
AREA
SENSORS
SAFETY
COMPONENTS
PRESSURE
SENSORS
INDUCTIVE
PROXIMITY
SENSORS
PARTICULAR
USE
SENSORS
SENSOR
OPTIONS
WIRE-
SAVING
SYSTEMS
MEASURE-
MENT
SENSORS
STATIC
CONTROL
DEVICES
LASER
MARKERS
Selection
Guide
Fiber Sensor
Amplifiers
FX-300
FX-100
Fibers
FT / FD / FR
FX-410
FX-311
FX-11A
FX-301-F
Other
Products
FIBER
SENSORS
FX-100
Fiber sensor
Ampilifi ers
PRECAUTIONS FOR PROPER USE
Refer to p.986~ for general precautions, and to the “Operation Guide” or “SUNX website”
(http://www.sunx.com) for details pertaining to operating instructions for the amplifi er.
Never use this product as a sensing device
for personnel protection.
In case of using sensing devices for
personnel protection, use products which
meet laws and standards, such as OSHA,
ANSI or IEC etc., for personnel protection
applicable in each region or country.
•
•
The FX-100 series does not use the horizontal
connectors that are used with the FX-300 / FX-400
series. Please note that horizontal connection cannot be
performed using a connector attached cable. In addition,
the optical communication function is not equipped on
the FX-100 series, so it is unable to perform interference
prevention for use with the FX-300 / FX-400 series.
If using the FX-100 series together with the FX-300 /
FX-400 series side-by-side, please set the same models
together in groups.
•
Using in combination with the FX-300 / FX-400 series
Mounting
<When using a DIN rail>
How to mount the amplifi er
1
Fit the rear part of the mounting
section of the amplifi er on a 35 mm
1.378 in width DIN rail.
2
Press down the rear part of the
mounting section of the unit on the
35 mm 1.378 in width DIN rail and
fi t the front part of the mounting
section to the DIN rail.
Part description
Setting mode
Setting mode appears after the MODE key is pressed for
2 sec. in RUN mode.
•
Setting item
Factory setting
Description
Teaching
mode
Threshold value can be set in 2-level teaching,
limit teaching, or full-auto teaching.
Output
operation
setting
[Dark-ON] Light-ON or Dark-ON can be set.
Timer
operation
setting
[Without timer]
Without timer, ON delay timer, or OFF delay
timer can be set.
Timer
setting
[ON-delay timer: 10 ms]
[OFF-delay timer: 10 ms]
In case of setting ON-delay timer or OFF-delay
timer in the timer operation setting mode, timer
can be set. When timer is not set, this mode is
not displayed.
Emission
amount
setting
[OFF]
Setting for reduced intensity of emission
amount is possible when the incident light
intensity is saturated.
Emission
frequency
setting
FX-101□
0 (Response time:
250 μs or less)
FX-102□
1 (Response time:
2.5 ms or less)
In case of using the fi ber heads in parallel,
interference can be prevented by setting
different emission frequency. However, when
emission frequency 0 is set, interference
cannot be prevented. Response time
corresponds to emission frequency. For
details, refer to “SPECIFICATIONS” on p.132.
Operation indicator
(Orange) MODE key
ON key /
Setting value UP key
OFF key /
Setting value DOWN key
Digital display (Green)
(Threshold value)
Digital display (Red)
(Incident light intensity)
35 mm 1.378 in width DIN rail
1
2
How to remove the amplifi er
1
Push the amplifi er forward.
2
Lift up the front part of the
amplifi er to remove it.
Note: Take care that if the front part is lifted without pushing the amplifi er
forward, the hook on the rear portion of the mounting section is likely
to break.
<When using screws with washers>
Use M3 screws with washers
for mounting. The tightening
torque should be 0.5 N·m or
less.
•
1
2
M3 screw
with washer
Digital Fiber Sensor FX-100 SERIES
136
FIBER
SENSORS
LASER
SENSORS
PHOTO-
ELECTRIC
SENSORS
MICRO
PHOTO-
ELECTRIC
SENSORS
AREA
SENSORS
SAFETY
COMPONENTS
PRESSURE
SENSORS
INDUCTIVE
PROXIMITY
SENSORS
PARTICULAR
USE
SENSORS
SENSOR
OPTIONS
WIRE-
SAVING
SYSTEMS
MEASURE-
MENT
SENSORS
STATIC
CONTROL
DEVICES
LASER
MARKERS
Selection
Guide
Fiber Sensor
Amplifiers
FX-300
FX-100
Fibers
FT / FD / FR
FX-410
FX-311
FX-11A
FX-301-F
Other
Products
FIBER
SENSORS
FX-100
Fiber Sensor
Amplifi ers
PRO mode
PRO mode appears after the MODE key is pressed for 4
sec. in RUN mode.
•
Setting item
Factory setting
Description
Shift
setting
[Shift amount 15 %]
Shift amount can be selected from 0 to 80 % in
the limit teaching. Select 0 % when it is desired
to set the present incident light intensity as a
threshold value.
External
input
setting [Emission halt]
Extemal input can be selected from emission
halt, limit +, limit -, AUTO, and ECO.
Threshold
value
follow-up
cycle
setting
(Note 1)
[OFF]
When incident light intensity exceeds threshold
value, this mode can change the threshold
value with each set cycle depending on
variations of the incident light intensity. The
follow-up shift amount is same as the one
set in the shift setting mode. However, the
threshold value is not stored.
GETA
function
setting
(Note 2, 3)
[OFF]
Variations can be reduced by correcting the
present incident light intensity in each amplifi er
to a target value. Target value to offset incident
light intensity can be selected from 0 to 2,000
by 100 unit each. For example, if the target
value is set to 2,000 when the incident light
intensity is 1,500, the incident light intensity
becomes 2,000.
ECO
setting [OFF]
It is possible to light up / turn off the digital
display. When ECO setting mode is ON, the
display turns off in 20 sec. approx. in RUN
mode. To light up the display again, press any
key for 2 sec. or more.
Digital
display
inversion
setting
[OFF] Digital display can be inverted.
Threshold
value
margin
setting
[OFF]
Margin for threshold value to the present
incident light intensity can be checked. When
there is no margin, it is possible to make the
digital display blink.
: Set to “OFF”: does not function.
: Green blinks.
: Red blinks.
: Red and green blink.
Setting
copy [NO]
The settings of the master side amplifi er can
be copied to the slave side amplifi er.
For details, refer to “Setting copy function.”
Reset [NO] Returns to default settings (factory settings.)
Notes: 1) If the incident light intensity becomes “300” or less, the follow-up
operation stops. In that condition, threshold value [digital display
(green)] blinks.
This function can be used when thru-beam type or retrorefl ective
type fi ber is applied to this product. If refl ective type fi ber is
applied, the function cannot be used depending on use conditions.
2) If MODE key is pressed in RUN mode when GETA function is
used, the incident light intensity before setting GETA function is
displayed on the red digital display for 2 sec. approx.
3) When GETA function is used in saturation of incident light intensity
(4,000 or more,) “ ” is indicated on the red digital display.
Correction value is up to 4,000.
Setting copy function
This can copy the settings of the master side amplifi er to
the slave side amplifi er.
•
Be sure to use the setting copy function between the
identical models (Between FX-10□ models or FX-102□
models).
This function cannot be used between different
models.
Only one sensor can be connected on slave side with a
master side sensor for the setting copy function.
Threshold value, output operation setting, timer
operation setting, timer setting, light-emitting amount
setting, shift setting, ECO setting, digital display
inversion setting, and threshold value margin setting
can be copied.
•
•
•
<Setting procedures>
1
Set the setting copy mode of the master side amplifi er to
“Copy sending ON”, and press the MODE key so that
“ ” is shown on the digital display and the
sensor is in copy ready state. For the setting method,
refer to “Operation guide”.
2
Turn off the master side amplifi er.
3
Connect the master side amplifi er with the slave side
amplifi er as shown below.
4
Turn on the master side amplifi er and the slave side
amplifi er at the same time. (Note)
5
“ ” is shown on the green digital display of the master
side amplifi er and 4-digit code is shown on the red
digital display of it, then the copying starts. During copy
communication, “ ” is shown on the green digital
display of the slave side amplifi er, and the ongoing copy
communication indicator (“ ”“ ”“ ”
“ ”) is displayed on the red digital display.
6
When the copying is completed, “ ” is shown on the
green digital display of the slave side amplifi er, while the
4-digit code (the same code as the master side amplifi er)
is shown on the red digital display of it.
7
Turn off the power of the master side amplifi er and the
slave side amplifi er and disconnect the wire.
If copying the settings to another amplifi er repeatedly, follow the steps
3
to
7
.
Note: Take care that if the power is not turned on at the same time, the
setting contents may not be copied.
<To cancel the setting copy mode of the master side amplifi er>
1
While the slave side amplifi er is disconnected, turn on
the power of the master side amplifi er.
2
Press the MODE key for 2 sec. approx.
*
Master side amplifier
Slave side amplifier
Color code of cable with connector
+
–
12 to 24V DC
± 10 %
(Brown) +V
(Black) Input
(White) Extemal input
(Blue) 0 V
(Brown) +V
(Black) Input
(White) Extemal input
(Blue) 0 V
PRECAUTIONS FOR PROPER USE
Refer to p.986~ for general precautions, and to the “Operation Guide” or “SUNX website”
(http://www.sunx.com) for details pertaining to operating instructions for the amplifi er.
137
Digital Fiber Sensor FX-100 SERIES
FIBER
SENSORS
LASER
SENSORS
PHOTO-
ELECTRIC
SENSORS
MICRO
PHOTO-
ELECTRIC
SENSORS
AREA
SENSORS
SAFETY
COMPONENTS
PRESSURE
SENSORS
INDUCTIVE
PROXIMITY
SENSORS
PARTICULAR
USE
SENSORS
SENSOR
OPTIONS
WIRE-
SAVING
SYSTEMS
MEASURE-
MENT
SENSORS
STATIC
CONTROL
DEVICES
LASER
MARKERS
Selection
Guide
Fiber Sensor
Amplifiers
FX-300
FX-100
Fibers
FT / FD / FR
FX-410
FX-311
FX-11A
FX-301-F
Other
Products
FIBER
SENSORS
FX-100
Fiber sensor
Ampilifi ers
Code setting function
Settings for “output operation”, “timer”, “emission
amount”, “emission frequency”, “ECO”, “external input”,
and “shift amount” are possible by selecting codes
discretionary.
The code setting function makes it possible to set the
output operation, timer operation, amount of light emitted,
frequency of light emitted, ECO setting, external input,
and amount of shift by selecting a code of one’s choice.
While in the RUN Mode, pressing and holding both
the ON key ( ) and OFF key ( ) simultaneously for 4
seconds will switch to the code setting function.
•
•
•
Quick setting function
Settings for “output operation”, “light-emitting amount”,
“timer”, and “emission frequency” are possible simply by
selecting a setting number.
The quick setting function makes it possible to set
the content of the SET Mode (output operation, timer
operation, amount of light emitted, and frequency of light
emitted) simply by selecting a setting number.
While in the RUN Mode, pressing and holding both
the ON key ( ) and OFF key ( ) simultaneously for 2
seconds will switch to the quick setting function.
•
•
•
<Table of quick setting numbers>
No.
Output operation
Emission amount setting
Timer
D-ON OFF non
D-ON ON non
D-ON OFF ofd 10 ms
D-ON ON ofd 10 ms
D-ON OFF ofd 40 ms
D-ON ON ofd 40 ms
D-ON OFF ond 10 ms
D-ON ON ond 10 ms
D-ON OFF ond 40 ms
D-ON ON ond 40 ms
L-ON ON ond 40 ms
L-ON OFF ond 40 ms
L-ON ON ond 10 ms
L-ON OFF ond 10 ms
L-ON ON ofd 40 ms
L-ON OFF ofd 40 ms
L-ON ON ofd 10 ms
L-ON OFF ofd 10 ms
L-ON ON non
L-ON OFF non
Others
Do not use during the initial transient time (0.5 sec.) after
the power supply is switched on.
EEPROM is adopted to this product. It is not possible to
conduct teaching 100 thousand times or more, because
of the EEPROM’s lifetime.
•
•
PRECAUTIONS FOR PROPER USE
Refer to p.986~ for general precautions, and to the “Operation Guide” or “SUNX website”
(http://www.sunx.com) for details pertaining to operating instructions for the amplifi er.
<Code table>
Code
1st digit 2nd digit 3rd digit
4th digit
Output
operation
Timer
(Note5)
Emission
amount
setting
Emission
Frequency ECO
Extemal
input
Shift
(Note5)
FX-101□FX-102□
D-on
non
OFF
01
OFF
E_oF 5 %
ond 10 ms
12
Limit [+]
10 %
ond 40 ms
23
Limit [–]
15 %
ofd 10 ms
3 4 Auto 20 %
ofd 40 ms
ON
0 1 Eco 25 %
L-on
non 1 2
ON
E_oF 30 %
ond 10 ms
23
Limit [+]
35 %
ond 40 ms
34
Limit [–]
40 %
ofd 10 ms
Auto 45 %
ofd 40 ms
Eco 50 %
Notes: 1) When the present setting is out of the code setting range, “ ” is
shown.
When “ ” is selected, the set content of the digit is not changed.
2) The factory setting is “ ”.
Digital Fiber Sensor FX-100 SERIES
138
FIBER
SENSORS
LASER
SENSORS
PHOTO-
ELECTRIC
SENSORS
MICRO
PHOTO-
ELECTRIC
SENSORS
AREA
SENSORS
SAFETY
COMPONENTS
PRESSURE
SENSORS
INDUCTIVE
PROXIMITY
SENSORS
PARTICULAR
USE
SENSORS
SENSOR
OPTIONS
WIRE-
SAVING
SYSTEMS
MEASURE-
MENT
SENSORS
STATIC
CONTROL
DEVICES
LASER
MARKERS
Selection
Guide
Fiber Sensor
Amplifiers
FX-300
FX-100
Fibers
FT / FD / FR
FX-410
FX-311
FX-11A
FX-301-F
Other
Products
FIBER
SENSORS
FX-100
Fiber Sensor
Amplifi ers
DIMENSIONS (Unit: mm in)Refer to p.106
~
for fi ber dimensions.
The CAD data in the dimensions can be downloaded from the website: http://www.sunx.com
10
0.394
64.5 2.539
13.5
0.531 35 1.378
5.5
0.217 50 1.969
4.1
0.161
2
0.079
3
0.118
ø3.2
ø0.126
1.1
0.043
9
0.354
7
0.276
1
0.039
8.1
0.319
3.2
0.126
2.7
0.106
4
0.157
0.8
0.031
6
0.236
6
0.236
10.85
0.427
12.2
0.480
0.7 0.028
MODE key
ON key / Setting value UP key
OFF key / Setting value DOWN key
Operation indicator (Orange)
Digital display (Green, Red)
29 1.142
47 1.850
30
1.181
10
0.394
ø6.5
ø0.256
Suitable for 35 mm 1.378 in width DIN rail
4.1
0.161
2.7
0.106
0.8
0.031
6 0.236 6 0.236
20
0.787
47 1.850
29 1.142
12.2
0.480
0.7
0.028
MODE key
ON key / Setting value UP key
OFF key / Setting value DOWN key
Operation indicator (Orange)
Digital display (Green, Red)
FX-101□ FX-102□Amplifi er FX-101(P)-Z FX-102(P)-Z Amplifi er
5
0.197
24.5
0.965
1
0.039
4
0.157
11.5
0.453
35
1.378
9
0.354
9.25
0.364
15
0.591
1
0.039
ø3.2 ø0.126
ø3.2 ø0.126
3.2
0.126
3.2
0.126
7.2 mm 0.283 in
spot facing, 4 0.157 deep
6.2 mm 0.244 in
spot facing, 3 0.118 deep
ø7.2 mm ø0.283 in
spot facing, 4 0.157 deep
ø6.2 mm ø0.244 in
spot facing, 3 0.118 deep
1.6
0.063
32
1.260 4
0.157
5.6
0.220
2.75 0.108 M3 (Iength 18 mm 0.709 in) pan head screws
M3 Square nut
24.7
0.972
15
0.591
3 0.118
3
0.118
60
2.362
Suitable for 35 mm 1.378 in width DIN rail
MS-DIN-4 Amplifer mounting bracket (Optional) MS-DIN-E End plate (Optional)
Material: PBT
Material: Polycarbonate
( ) ( )
( )
ø3.7 ø0.146 cable
8
0.315
L
35
1.378
50
1.969
8
0.315
( )
Model No. Length L
CN-14A(-R)-C1
1,000 39.370
CN-14A(-R)-C2
2,000 78.740
CN-14A(-R)-C3
3,000 118.110
CN-14A(-R)-C5
5,000 196.850
CN-14A-C2 is attached FX-101(P)-CC2 / FX-102(P)-CC2
CN-14A-C□ CN-14A-R-C□Connector attached cable (Optional)
• Length L
Assembly dimensions with optional protective cover
(FC-FX-1)
10
0.394
9
0.354
64.5 2.539
13.5
0.531 35 1.378
5.5 0.217 50 1.969
66.2
2.606
2
0.079
2 0.079
2 0.079
3 0.118
1.1
0.043
7
0.276 0.8
0.031 30
1.181
8.1
0.319
10
0.394
3.2
0.126
4
0.157
6 0.236
0.75 0.030
Suitable for 35 mm 1.378 in width DIN rail
ø3.2
ø0.126
0.8
0.031
1.1
0.043
10
0.394
7
0.276
9
0.354
4
0.157
5.5 0.217 13.5
0.531
50 1.969
35 1.378
64.5 2.539
2
0.079
3.2
0.126
8.1
0.319
10
0.394
30
1.181
1
0.039
Suitable for 35 mm 1.378 in width DIN rail
ø3.2
ø0.126
3 0.118
