Microstructure Pressure Sensors Low Cost, Compensated, DIP Package 0 psi to 1 psi up to 0 psi to 100 psi SDX Series FEATURES * Low Cost DIP * Precision Temperature Compensation * Calibrated Zero & Span * Small Size * Low Noise * High Impedance for Low Power Applications * Prime Grade Available (SDXxxxyy-A) TYPICAL APPLICATIONS * Medical Equipment * Computer Peripherals * Pneumatic Controls * HVAC The SDX series sensors provide a very cost effective solution for pressure applications that require small size plus performance. These calibrated and temperature compensated sensors give an accurate and stable output over a 0 C to 50 C [32 F to 122 F] temperature range. This series is intended for use with non-corrosive, non-ionic working fluids such as air, dry gases and the like. Devices are available to measure absolute and gage pressures from 1 psi (SDX01) up to 100 psi (SDX100). The absolute devices have an internal vacuum reference and an output voltage proportional to absolute pressure. The SDX devices are available in standard commercial and prime grades (SDCxxxyy - A) to allow optimization of accuracy and cost in any given application. The SDX devices feature an integrated circuit (IC) sensor element and laser trimmed thick film ceramic housed in a compact solvent resistant case. The package is a double-wide (i.e. 0.600 inches lead spacing) dual-inline package (DIP). This is the same familiar package used by IC manufacturers except it is only 11,94 mm [0.470 in] long and has a pressure port(s). The pc 2 board area used by each DIP is approximately 0.26 in . This extremely small size enables the use of multiple sensors in limited available space. The DIP provides excellent corrosion resistance and isolation to external package stress. The DIP mounts on a pc board like a standard IC with through-hole pins. The pins anchor the pressure sensor to the pc board and provide a more secure and stable unit than other types of packages. WARNING PERSONAL INJURY DO NOT USE these products as safety or emergency stop devices or in any other application where failure of the product could result in personal injury. Failure to comply with these instructions could result in death or serious injury. Sensing and Control The output of the bridge is ratiometric to the supply voltage and operation from any dc supply voltage up to 20 Vdc is acceptable. Contact your local honeywell representative or go to Honeywell's website at www.honeywell.com/sensing for additional details. WARNING MISUSE OF DOCUMENTATION * The information presented in this product sheet is for reference only. Do not use this document as a product installation guide. * Complete installation, operation, and maintenance information is provided in the instructions supplied with each product. Failure to comply with these instructions could result in death or serious injury. Microstructure Pressure Sensors Low Cost, Compensated, DIP Package 0 psi to 1 psi up to 0 psi to 100 psi SDX Series PRESSURE RANGE SPECIFICATIONS Model No*, Pressure Connection, Pressure Type Gage SDX01G2 SDX01G2-A SDX05G2 SDX05G2-A SDX15G2 SDX15G2-A SDX30G2 SDX30G2-A SDX100G2 SDX100G2-A Diff/Gage SDX01D4 SDX01D4-A SDX05D4 SDX05D4-A SDX15D4 SDX15D4-A SDX30D4 SDX30D4-A SDX100D4 SDX100D4-A Absolute ------SDX15A2 SDX15A4 SDX15A2-A SDX15A4-A --SDX30A2 SDX30A4 SDX30A2-A SDX30A4-A --SDX100A2 SDX100A4 SDX100A2-A SDX100A4-A Operating Pressure Proof (2) Pressure 0 psid to 1 psid 20 psid 0 psid to 5 psid 20 psid 0 psid to 15 psid 30 psid 0 psia to 15 psia 30 psia 0 psid to 30 psid 60 psid 0 psia to 30 psia 60 psia 0 psid to 100 psid 150 psid 0 psia to 100 psia 150 psia Full-Scale Span Min. Typ. Max. 17.37 mV 17.82 mV 57.90 mV 59.40 mV 86.85 mV 89.10 mV 86.85 mV 86.85 mV 89.10 mV 89.10 mV 86.85 mV 89.10 mV 86.85 mV 86.85 mV 89.10 mV 89.10 mV 96.50 mV 99.00 mV 96.50 mV 96.50 mV 99.00 mV 99.00 mV 18.00 mV 18.00 mV 60.00 mV 60.00 mV 90.00 mV 90.00 mV 90.00 mV 90.00 mV 90.00 mV 90.00 mV 90.00 mV 90.00 mV 90.00 mV 90.00 mV 90.00 mV 90.00 mV 100.00 mV 100.00 mV 100.00 mV 100.00 mV 100.00 mV 100.00 mV 18.63 mV 18.80 mV 62.10 mV 60.60 mV 93.15 mV 90.90 mV 93.15 mV 93.15 mV 90.90 mV 90.90 mV 93.15 mV 90.90 mV 93.15 mV 93.15 mV 90.90 mV 90.90 mV 103.5 mV 101.0 mV 103.5 mV 103.5 mV 101.0 mV 101.0 mV * Ordering information: Order model number. (-A) = Prime Grade Pressure Connection and Pressure Type G2 = "D2" DIP Package, Temperature Compensated Gage Sensor G2-A = "D2" DIP Package, Prime Grade, Temperature Compensated Gage Sensor D4 = "D4" DIP Package, Temperature Compensated Differential Sensor D4-A = "D4" DIP Package, Prime Grade, Temperature Compensated Differential Sensor A2 = "D2" DIP Package, Temperature Compensated Absolute Sensor A2-A = "D2" DIP Package, Prime Grade, Temperature Compensated Absolute Sensor A4 = "D4" DIP Package, Temperature Compensated Absolute Sensor A4-A = "D4" DIP Package, Prime Grade, Temperature Compensated Absolute Sensor GENERAL SPECIFICATIONS Characteristic Supply Voltage (VS) Common Mode Pressure Lead Soldering Temperature (2 seconds to 4 seconds) Description (Maximum Ratings) All Devices 20 Vdc 150 psig 250 C [482 F] ENVIRONMENTAL SPECIFICATIONS Characteristic Compensated Operating Temperature Operating Temperature Storage Temperature Humidity Limits 2 Honeywell * Sensing and Control (1) Description (Maximum Ratings) All Devices 0 C to 50 C [32 F to 122 F] -40 C to 85 C [-40 F to 185 F] -55 C to 125 C [-67 F to 257 F] 0 % RH to 100 % RH Microstructure Pressure Sensors Low Cost, Compensated, DIP Package 0 psi to 1 psi up to 0 psi to 100 psi SDX SERIES PERFORMANCE CHARACTERISTICS SDX Series (3) Characteristic Zero Pressure Offset (4) Zero Pressure Offset (Prime Grade) (5) Combined Linearity and Hysteresis (5) (13) Combined Linearity and Hysteresis (Prime Grade) (6) Temperature Effect on Span 0 C to 50 C [32 F to 122 F] (6) Temperature Effect on Span 0 C to 50 C [32 F to 122 F] (Prime Grade) (6) Temperature Effect on Offset 0 C to 50 C [32 F to 122 F] (6) Temperature Effect on Offset 0 C to 50 C [32 F to 122 F] (Prime Grade) (7) Repeatability (8) Input Resistance (9) Output Resistance (10) Common Mode Voltage (11) Response Time (12) Long Term Stability of Offset and Span Min. -1.0 -0.3 - - - - - - - - - 1.5 - - Typ. 0.0 0.0 0.2 0.1 0.4 0.4 0.2 0.2 0.2 4.0 4.0 3.0 100 0.1 Max. +1.0 0.3 1.0 0.25 2.0 1.0 1.0 0.5 0.5 - - 5.0 - - Unit mV mV % FSO % FSO % FSO % FSO mV mV % FSO kOhm kOhm Vdc S mV SPECIFICATION NOTES Note 1: Note 2: Note 3: Note 4: Note 5: Note 6: Note 7: Note 8: Note 9: Note 10: Note 11: Note 12: Note 13: Full-Scale Span is the algebraic difference between the output voltage at full-scale pressure and the output at zero pressure. Full-Scale Span is ratiometric to the supply voltage. Maximum pressure above which causes permanent sensor failure. Reference Conditions: (Unless otherwise noted) T A = 25 C, Supply VS = 12 Vdc, Common Mode Line pressure = 0 psig, Pressure applied to Port B. For absolute devices only, pressure is applied to Port A, and the output polarity is reversed. Maximum zero pressure offset for absolute devices is 500 Microvolt. Hysteresis - the maximum output difference at any point within the operating pressure range for increasing and decreasing pressure. Maximum error band of the offset voltage and the error band of the span, relative to the 25 C [77 F] reading. Maximum difference in output at any pressure within the operating pressure range and the temperature within 0 C to 50 C [32 F to 122 F] after: a) 100 temperature cycles, 0 C to 50 C [32 F to 122 F] b) 1.0 million pressure cycles, 0 psi to full-scale span. Input resistance is the resistance between VS and ground. Output resistance is the resistance between the + and - outputs. Common Mode voltage of the output arms for VS=12 Vdc. Response time for a 0 psi to Full-Scale Span pressure step change, 10 % to 90 % rise time. Long term stability over a one-year period. Maximum combined Linearity and Hysteresis for the SDX05 prime grade is 0.5 %. ELECTRICAL CONNECTIONS Honeywell * Sensing and Control 3 Microstructure Pressure Sensors Low Cost, Compensated, DIP Package 0 psi to 1psi up to 0 psi to 100psi SDX Series PHYSICAL DIMENSIONS for Reference Only (mm/in) SDX A2/G2 Package SDX A4 Package SDX D4 Package WARRANTY/REMEDY Honeywell warrants goods of its manufacture as being free of defective materials and faulty workmanship. Contact your local sales office for warranty information. If warranted goods are returned to Honeywell during the period of coverage, Honeywell will repair or replace without charge those items it finds defective. The foregoing is Buyer's sole remedy and is in lieu of all other warranties, expressed or implied, including those of merchantability and fitness for a particular purpose. Specifications may change without notice. The information we supply is believed to be accurate and reliable as of this printing. However, we assume no responsibility for its use. Sensing and Control www.honeywell.com/sensing Honeywell 11 West Spring Street Freeport, Illinois 61032 008103-2-EN IL50 GLO 104 Printed in USA Copyright 2003 Honeywell International Inc. All Rights Reserved While we provide application assistance personally, through our literature and the Honeywell web site, it is up to the customer to determine the suitability of the product in the application. For application assistance, current specifications, or name of the nearest Authorized Distributor, contact a nearby sales office. Or call: 1-800-537-6945 USA/Canada 1-815-235-6847 International FAX 1-815-235-6545 USA INTERNET www.honeywell.com/sensing info.sc@honeywell.com Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Honeywell: SDX01D4 SDX01D4-A SDX01G2 SDX01G2-A SDX05D4 SDX05G2 SDX05G2-A SDX100A2 SDX100A4 SDX100D4 SDX100G2 SDX15A2 SDX15A2-A SDX15A4 SDX15A4-A SDX15D4 SDX15D4-A SDX15G2 SDX15G2-A SDX30A2 SDX30A2-A SDX30A4 SDX30D4 SDX30G2