SA SERIES
FEATURES
Glass passivated chip
Low leakage
Uni and Bidirectional unit
Excellent clamping capability
The plastic material has U/L recognition 94V-O
Fast response time
MECHANICAL DATA
Case : Molded Plastic
Marking : Unidirectional - type number and cathode
band Bidirectional - type number only
Weight : 0.34 grams
T
J
Operating Temperature Range
-55 to +175
T
STG
Storage Temperature Range
-55 to +175
C
I
FSM
Peak Forward Surge Current 8.3ms
single half sine-wave @ T
J
= 25 ,
(Note 2)
70
AMPS.
UNIT
P
M(AV)
2.0
WATTS
Steady State Power Dissipation at T
L
=120
lead lenghts 0.375" (9.5mm) , see fig. 4
P
PK
WATTS
PEAK POWER DISSIPATION AT T
A
= 25 ,
TP = 1ms (Note 1)
SYMBOLS VALUE
500
C
CHARACTERISTICS
Max.
All Dimensions in millimeter
Min.
DO-15
Dim.
A
D
C
B
25.4
7.60
-
5.80
0.71
2.60 3.60
0.86
DO-15
A
C
D
A
B
GLASS PASSIVATED
UNIDIRECTIONAL AND BIDIRECTIONAL
TRANSIENT VOLTAGE SUPPRESSORS
REVERSE VOLTAGE -
5.0
to
170
Volts
POWER DISSIPATION -
500
WATTS
V
F
3.5 Volts
MaximumInstantaneous forward voltage
at 35A for unidirectional devices only
MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS
Ratings at 25 ambient temperature unless otherwise specified.
Single phase, half wave, 60Hz, resistive or inductive load.
For capacitive load, derate current by 20%
NOTES : 1. Non-repetitive current pulse, per fig. 5 and derated above TA= 25 C per fig. 1
2. 8.3ms single half sine-wave duty cycle= 4 pulses per minutes maximum (uni-directional units only).
SEMICONDUCTOR
LITE-ON
REV. 7, Nov-2010, KDID01
RATING AND CHARACTERISTIC CURVES
SA SERIES
FIG.1 - PULSE DERATING CURVE
PEAK PULSE DERATING IN % OF PEAK
POWER OR CURRENT
AMBIENT TEMPERATURE,
25 75 100 125 150
0
50
50
100
0175
75
25
200
10 X 1000 WAVEFORM
AS DEFINED BY R.E.A.
FIG.2 - TYPICAL JUNCTION CAPACITANCE
CAPACITANCE , (pF)
REVERSE VOLTAGE , VOLTS
10
1100
10000
1000
100
10
1000
PM
(AV)
, STEADY STATE POWER DISSIPATION (W)
FIG.4 - STEADY STATE POWER DERATING CURVE
TL, LEAD TEMPERATURE
25 75 100 125 150
0.0
50
0175 200
1.0
2.0
3.0
4.0
5.0
FIG.3 - PULSE RATING CURVE
P
P
, PEAK POWER ( K
W
)
T
P
, PULSE WIDTH
0.1
1.0
10
0.1us 1.0us 10us 100us 1.0ms 10ms
100
IMPULSE
SINE WAVE
SQUARE WAVE
4
60Hz RESISTIVE OR
INDUCTIVE LOAD
TJ =25 C
MEASURED AT
STAND-OFF VOLTAGE
UNIDIRECTIONAL
BIDIRECTIONAL
Non-repetive Pulse Waveform
Shown in Figure 5
T
A
=25 C
FIG.5 - PULSE WAVEFORM
0
0
I
P,
PEAK PULSE CURRENT , (% )
T , TIME ( ms )
50
100
1.0 2.0 3.0 4.0
T
R
=10us
Peak value (I
RSM)
TP
10 x 1000 waveform as
defined by R.E.A.
Pulse width (T
P
) is defined
as that point where the
peak current decays to 50%
of I
RSM
T
J
=25 C
I
RSM
2
Half value=
Type Number Type Number
Reverse
Standoff
Voltage
Max.
Clamping
Voltage
@Ipp
Max.
Peak
Pulse Current
Max. Reverse
Leakage @VR
(UNI) (BI) V
R
(V) Min (V) Max (V) It (mA) Vc (V) Ipp (A) I
R
(uA)
SA5.0A SA5.0CA 5.0 6.40 7.07 10 9.2 54.3 600
SA6.0A SA6.0CA 6.0 6.67 7.37 10 10.3 48.5 600
SA6.5A SA6.5CA 6.5 7.22 7.98 10 11.2 44.6 400
SA7.0A SA7.0CA 7.0 7.78 8.60 10 12.0 41.7 150
SA7.5A SA7.5CA 7.5 8.33 9.21 1 12.9 38.8 50
SA8.0A SA8.0CA 8.0 8.89 9.83 1 13.6 36.8 25
SA8.5A SA8.5CA 8.5 9.44 10.43 1 14.4 34.7 10
SA9.0A SA9.0CA 9.0 10.0 11.1 1 15.4 32.5 5
SA10A SA10CA 10 11.1 12.3 1 17.0 29.4 3
SA11A SA11CA 11 12.2 13.5 1 18.2 27.5 3
SA12A SA12CA 12 13.3 14.7 1 19.9 25.1 3
SA13A SA13CA 13 14.4 15.9 1 21.5 23.3 3
SA14A SA14CA 14 15.6 17.2 1 23.2 21.6 3
SA15A SA15CA 15 16.7 18.5 1 24.4 20.5 3
SA16A SA16CA 16 17.8 19.7 1 26.0 19.2 3
SA17A SA17CA 17 18.9 20.9 1 27.6 18.1 3
SA18A SA18CA 18 20.0 22.1 1 29.2 17.1 3
SA20A SA20CA 20 22.2 24.5 1 32.4 15.4 3
SA22A SA22CA 22 24.4 27.0 1 35.5 14.1 3
SA24A SA24CA 24 26.7 29.5 1 38.9 12.9 3
SA26A SA26CA 26 28.9 31.9 1 42.1 11.9 3
SA28A SA28CA 28 31.1 34.4 1 45.4 11.0 3
SA30A SA30CA 30 33.3 36.8 1 48.4 10.3 3
SA33A SA33CA 33 36.7 40.6 1 53.3 9.4 3
SA36A SA36CA 36 40.0 44.2 1 58.1 8.6 3
SA40A SA40CA 40 44.4 49.1 1 64.5 7.8 3
SA43A SA43CA 43 47.8 52.8 1 69.4 7.2 3
SA45A SA45CA 45 50.0 55.3 1 72.7 6.9 3
SA48A SA48CA 48 53.3 58.9 1 77.4 6.5 3
SA51A SA51CA 51 56.7 62.7 1 82.4 6.1 3
SA54A SA54CA 54 60.0 66.3 1 87.1 5.7 3
SA58A SA58CA 58 64.4 71.2 1 93.6 5.3 3
SA60A SA60CA 60 66.7 73.7 1 96.8 5.2 3
SA64A SA64CA 64 71.1 78.6 1 103.0 4.9 3
SA70A SA70CA 70 77.8 86.0 1 113.0 4.4 3
SA75A SA75CA 75 83.3 92.1 1 121.0 4.1 3
SA78A SA78CA 78 86.7 95.8 1 126.0 4.0 3
SA85A SA85CA 85 94.4 104.3 1 137.0 3.6 3
SA90A SA90CA 90 100 110.5 1 146.0 3.4 3
SA100A SA100CA 100 111 122.7 1 162.0 3.1 3
SA110A SA110CA 110 122 134.8 1 177.0 2.8 3
SA120A SA120CA 120 133 147.0 1 193.0 2.6 3
SA130A SA130CA 130 144 159.2 1 209.0 2.4 3
SA150A SA150CA 150 167 184.6 1 243.0 2.1 3
SA160A SA160CA 160 178 196.7 1 259.0 1.9 3
SA170A SA170CA 170 189 208.9 1 275.0 1.8 3
NOTE :
Suffix'C' denotes Bi-directional device. Suffix'A' denotes 5% tolerance device.
1. For Bi-directional devices having VR of 10 volts and under,the IR limit is doubled .
2. For Uni-directional devices VF max=3.5V at IF=35A, 0.5 sine wave of 8.33 msec. pulse width .
Breakdown Voltage
BV Volts @It
SEMICONDUCTOR
LITE-ON
Legal Disclaimer Notice
SA SERIES
LSC reserves the right to make changes to this document and its products and
specifications at any time without notice. Customers should obtain and confirm
the latest product information and specifications before final design, purchase or
use.
LSC makes no warranty, representation or guarantee regarding the suitability of
its products for any particular purpose, nor does LSC assume any liability for
application assistance or customer product design. LSC does not warrant or
accept any liability with products which are purchased or used for any
unintended or unauthorized application.
No license is granted by implication or otherwise under any intellectual property
rights of LSC.
LSC products are not authorized for use as critical components in life support
devices or systems without express written approval of LSC.
Important Notice and Disclaimer