E M C C o m p o n e n t s May 2018 Chip beads For general signal line GHz noise countermeasure (general signal line, high-speed line) MMZ-E series MMZ0603-E MMZ0603-E 0603[0201 inch]* * Dimensions code JIS[EIA] type (2/11) E M C C o m p o n e n t s REMINDERS FOR USING THESE PRODUCTS Before using these products, be sure to request the delivery specifications. SAFETY REMINDERS Please pay sufficient attention to the warnings for safe designing when using these products. REMINDERS The storage period is less than 12 months.Be sure to follow the storage conditions (temperature:5 to 40C, humidity:10 to 75% RH or less). If the storage period elapses, the soldering of the terminal electrodes may deteriorate. Do not use or store in locations where there are conditions such as gas corrosion (salt, acid, alkali, etc.). Before soldering, be sure to preheat components. The preheating temperature should be set so that the temperature difference between the solder temperature and chip temperature does not exceed 150C. Soldering corrections after mounting should be within the range of the conditions determined in the specifications. If overheated, a short circuit, performance deterioration, or lifespan shortening may occur. When embedding a printed circuit board where a chip is mounted to a set, be sure that residual stress is not given to the chip due to the overall distortion of the printed circuit board and partial distortion such as at screw tightening portions. Self heating (temperature increase) occurs when the power is turned ON, so the tolerance should be sufficient for the set thermal design. Carefully lay out the coil for the circuit board design of the non-magnetic shield type. A malfunction may occur due to magnetic interference. Use a wrist band to discharge static electricity in your body through the grounding wire. Do not expose the products to magnets or magnetic fields. Do not use for a purpose outside of the contents regulated in the delivery specifications. The products listed on this catalog are intended for use in general electronic equipment (AV equipment, telecommunications equipment, home appliances, amusement equipment, computer equipment, personal equipment, office equipment, measurement equipment, industrial robots) under a normal operation and use condition. The products are not designed or warranted to meet the requirements of the applications listed below, whose performance and/or quality require a more stringent level of safety or reliability, or whose failure, malfunction or trouble could cause serious damage to society, person or property. If you intend to use the products in the applications listed below or if you have special requirements exceeding the range or conditions set forth in the each catalog, please contact us. (1) Aerospace/aviation equipment (2) Transportation equipment (cars, electric trains, ships, etc.) (3) Medical equipment (4) Power-generation control equipment (5) Atomic energy-related equipment (6) Seabed equipment (7) Transportation control equipment (8) Public information-processing equipment (9) Military equipment (10) Electric heating apparatus, burning equipment (11) Disaster prevention/crime prevention equipment (12) Safety equipment (13) Other applications that are not considered general-purpose applications When designing your equipment even for general-purpose applications, you are kindly requested to take into consideration securing protection circuit/device or providing backup circuits in your equipment. 20180521 / beads_commercial_signal_mmz0603-e_en.fm (3/11) E M C C o m p o n e n t s Product compatible with RoHS directive Halogen-free Compatible with lead-free solders Chip beads For general signal line GHz noise countermeasure (general signal line, high-speed line) Overview of MMZ0603-E type FEATURES Noise reduction solution for general signal line. Compared to the MMZ series, it is a product that increases the SRF to GHz bands and can countermeasure nose at wide frequencies with 1 element. Compared to the MMZ series, it can attain high impedance at GHz bands. Various frequency characteristics with 4 materials of different features for countermeasures against everything from general signals to high-speed signals. APPLICATION Noise removal for mobile devices such as smartphones and tablet terminals, and various modules. Noise removal for PCs and recorders, household appliances such as STBs, smart grids, and industrial equipment. PART NUMBER CONSTRUCTION MMZ Series name 0603 S LxWxT dimensions (mm) 0603 0.6x0.3x0.3 Material name S A D F 121 E Impedance () at 100MHz 121 120 102 1000 Characteristic type E T 000 Packaging style Internal code T Taping 000 OPERATING TEMPERATURE RANGE, PACKAGE QUANTITY, PRODUCT WEIGHT Temperature ranges Operating Storage Type temperature temperature C C MMZ0603-E -55 to +125 -55 to +125 The storage temperature range is for after the circuit board is mounted. Package quantity Individual weight (pieces/reel) 15,000 mg 0.3 RoHS Directive Compliant Product: See the following for more details.https://product.tdk.com/info/en/environment/rohs/index.html Halogen-free: indicates that Cl content is less than 900ppm, Br content is less than 900ppm, and that the total Cl and Br content is less than 1500ppm. Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use. Please note that the contents may change without any prior notice due to reasons such as upgrading. 20180521 / beads_commercial_signal_mmz0603-e_en.fm (4/11) E M C C o m p o n e n t s MMZ0603-E type RECOMMENDED REFLOW PROFILE Preheating Soldering Natural cooling Peak T: Temperature T4 T3 T2 T3 t3 T1 t1 t2 t: Time Preheating Temp. T1 T2 150C 180C Time t1 60 to 120s Soldering Temp. Time T3 t2 230C 30 to 60s Peak Temp. T4 250 to 260C Time t3 10s Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use. Please note that the contents may change without any prior notice due to reasons such as upgrading. 20180521 / beads_commercial_signal_mmz0603-e_en.fm (5/11) E M C C o m p o n e n t s MMZ0603-E type MATERIAL CHARACTERISTIC S material: Standard type that features impedance characteristics similar to those of a typical ferrite core. For signal line applications in which the blocking region is near 100MHz. Impedance values selected for effectiveness at 40 to 300MHz. A material: This high-impedance product is based on the impedance frequency characteristics of our Y-material. The product offers excellent impedance characteristics, which is greater than 2500, in the vicinity of 100MHz range (MMZ1608A252B). D material: For applications calling for low insertion loss at low frequencies and sharply increasing impedance at high frequencies. Designed for high impedance at high frequencies (00MHz to 1GHz) for signal line applications. F material: This new product inherits the characteristic of our D-material, namely its sharp impedance rise time, and its impedance peak frequency has been shifted higher into range. The product offers excellent noise suppression from 600MHz to as high as in the GHz range. TYPICAL MATERIAL IMPEDANCE CHARACTERISTICS 2500 A 2000 D F 1500 1000 S 500 0 10 100 Frequency(MHz) 1000 Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use. Please note that the contents may change without any prior notice due to reasons such as upgrading. 20180521 / beads_commercial_signal_mmz0603-e_en.fm (6/11) E M C C o m p o n e n t s MMZ0603-E type SHAPE & DIMENSIONS 0.30.03 0.30.03 0.60.03 0.1min. Dimensions in mm 0.30 RECOMMENDED LAND PATTERN 0.25 0.30 0.25 Dimensions in mm Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use. Please note that the contents may change without any prior notice due to reasons such as upgrading. 20180521 / beads_commercial_signal_mmz0603-e_en.fm (7/11) E M C C o m p o n e n t s MMZ0603-E type ELECTRICAL CHARACTERISTICS CHARACTERISTICS SPECIFICATION TABLE Impedance [100MHz] ( ) 120 240 600 1000 120 240 330 470 600 1000 33 47 120 160 56 75 Tolerance 25% 25% 25% 25% 25% 25% 25% 25% 25% 25% 25% 25% 25% 25% 25% 25% [1GHz] ( ) 200 400 1000 1800 300 600 750 1000 1500 2300 200 300 1000 1400 700 950 Tolerance 40% 40% 40% 40% 40% 40% 40% 40% 40% 40% 40% 40% 40% 40% 40% 40% Measurement equipment Measurement item Product No. Impedance E4991A+16197 DC resistance Type-7556 Equivalent measurement equipment may be used. DC resistance Rated current Part No. ( )max. 0.37 0.71 1.60 2.60 0.44 0.86 1.00 1.30 1.70 2.90 0.6 0.76 2.4 2.90 1.9 2.6 (mA)max. 250 200 150 125 250 200 220 185 160 130 250 200 125 125 150 125 MMZ0603S121ET000 MMZ0603S241ET000 MMZ0603S601ET000 MMZ0603S102ET000 MMZ0603A121ET000 MMZ0603A241ET000 MMZ0603A331ET000 MMZ0603A471ET000 MMZ0603A601ET000 MMZ0603A102ET000 MMZ0603D330ET000 MMZ0603D470ET000 MMZ0603D121ET000 MMZ0603D161ET000 MMZ0603F560ET000 MMZ0603F750ET000 Manufacturer Keysight Technologies Yokogawa Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use. Please note that the contents may change without any prior notice due to reasons such as upgrading. 20180521 / beads_commercial_signal_mmz0603-e_en.fm (8/11) E M C C o m p o n e n t s MMZ0603-E ELECTRICAL CHARACTERISTICS Z VS. FREQUENCY CHARACTERISTICS (BY SERIES) MMZ0603S-E series MMZ0603A-E series 2000 1800 MMZ0603S102E 1600 1200 MMZ0603S601E 1000 800 600 Impedance () 1400 1400 2000 MMZ0603A601E MMZ0603A471E 1500 MMZ0603A331E MMZ0603241E 1000 MMZ0603A121E 1200 1000 MMZ0603D470E 800 MMZ0603D330E 600 400 500 200 200 0 MMZ0603D121E 1600 MMZ0603S241E 400 MMZ0603D161E 1800 MMZ0603A102E 2500 Impedance() 2000 Impedance() MMZ0603D-E series 3000 1 MMZ0603S121E 10 100 1000 10000 Frequency (MHz) 0 1 10 100 1000 Frequency (MHz) 10000 0 1 10 100 1000 Frequency (MHz) 10000 MMZ0603F-E series 2500 MMZ0603F750E Impedance() 2000 MMZ0603F560E 1500 1000 500 0 1 10 100 1000 Frequency (MHz) 10000 Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use. Please note that the contents may change without any prior notice due to reasons such as upgrading. 20180521 / beads_commercial_signal_mmz0603-e_en.fm (9/11) E M C C o m p o n e n t s MMZ0603-E type ELECTRICAL CHARACTERISTICS Z, X, R VS. FREQUENCY CHARACTERISTICS MMZ0603S121ET000 MMZ0603S241ET000 200 Z R 100 X 50 100 1000 Frequency (MHz) 10000 2000 1800 1600 1400 1200 1000 800 600 400 200 0 Z R X 1 10 100 1000 Frequency (MHz) 10000 MMZ0603A331ET000 Impedance () Impedance () 800 Z R 400 X 200 0 1 10 100 1000 Frequency (MHz) 10000 MMZ0603A102ET000 Impedance () Impedance () 2500 Z 1500 R 1000 X 500 0 1 10 100 1000 Frequency (MHz) 10000 Impedance () R X 10 R X 10 1400 1200 1000 800 600 400 200 0 100 1000 Frequency (MHz) 10000 R X 10 350 300 250 200 150 100 50 0 100 1000 Frequency (MHz) X 100 1000 Frequency (MHz) 1600 1400 1200 1000 800 600 400 200 0 10000 X 1 10 100 1000 Frequency (MHz) 10000 800 700 600 500 400 300 200 100 0 Z R X 1 10 100 1000 Frequency (MHz) 10000 1600 1400 1200 1000 800 600 400 200 0 Z R X 1 10 100 1000 Frequency (MHz) 10000 MMZ0603D470ET000 R 10 0 10000 Z 1 200 MMZ0603A601ET000 Z 1 R 400 MMZ0603A241ET000 Z 1 600 10000 100 1000 Frequency (MHz) 10000 MMZ0603F560ET000 Z 1 350 300 250 200 150 100 50 0 500 450 400 350 300 250 200 150 100 50 0 Z R X 1 10 100 1000 Frequency (MHz) 10000 MMZ0603F750ET000 2500 Impedance () MMZ0603D121ET000 2000 1800 1600 1400 1200 1000 800 600 400 200 0 100 1000 Frequency (MHz) MMZ0603D330ET000 3000 2000 10 MMZ0603A471ET000 1000 600 1 MMZ0603A121ET000 Impedance () Impedance () MMZ0603S102ET000 X Impedance () 10 R Z 800 Impedance () 1 1000 Z Impedance () 0 1200 Z Impedance () 150 450 400 350 300 250 200 150 100 50 0 Impedance () Impedance () Impedance () 250 MMZ0603S601ET000 R X 1 10 100 1000 Frequency (MHz) 10000 2000 1500 Z R 1000 500 0 X 1 10 100 1000 Frequency (MHz) 10000 Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use. Please note that the contents may change without any prior notice due to reasons such as upgrading. 20180521 / beads_commercial_signal_mmz0603-e_en.fm (10/11) E M C C o m p o n e n t s MMZ0603-E type ELECTRICAL CHARACTERISTICS Impedance () Z, X, R VS. FREQUENCY CHARACTERISTICS MMZ0603D161ET000 2000 1800 1600 1400 1200 1000 800 600 400 200 0 Z R X 1 10 100 1000 Frequency (MHz) 10000 Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use. Please note that the contents may change without any prior notice due to reasons such as upgrading. 20180521 / beads_commercial_signal_mmz0603-e_en.fm (11/11) E M C C o m p o n e n t s MMZ0603-E type PACKAGING STYLE REEL DIMENSIONS o60min. 2.00.5 1.0 8.4 +2.0 -0.0 o130.2 o210.8 14.4max. o1802.0 Dimensions in mm 4.00.1 B A 8.00.3 2.00.05 3.50.05 1.5 +0.1 0 1.750.1 TAPE DIMENSIONS P1 K Dimensions in mm Type MMZ0603-E 160min. Drawing direction A 0.380.05 Taping B 0.680.05 P1 2.00.05 K 0.5max. 200min. 300min. Dimensions in mm Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use. Please note that the contents may change without any prior notice due to reasons such as upgrading. 20180521 / beads_commercial_signal_mmz0603-e_en.fm