May 2018
EMC Components
For general signal line
GHz noise countermeasure (general signal line, high-speed line)
MMZ0603-E 0603[0201 inch]*
* Dimensions code JIS[EIA]
Chip beads
MMZ0603-E
type
MMZ-E series
(2/11)
20180521 / beads_commercial_signal_mmz0603-e_en.fm
EMC Components
REMINDERS FOR USING THESE PRODUCTS
Before using these products, be sure to request the delivery specifications.
SAFETY REMINDERS
Please pay sufficient attention to the warnings for safe designing when using these products.
The storage period is less than 12 months.Be sure to follow the storage conditions (temperature:5 to 40°C, humidity:10 to 75% RH or
less).
If the storage period elapses, the soldering of the terminal electrodes may deteriorate.
Do not use or store in locations where there are conditions such as gas corrosion (salt, acid, alkali, etc.).
Before soldering, be sure to preheat components.
The preheating temperature should be set so that the temperature difference between the solder temperature and chip temperature
does not exceed 150°C.
Soldering corrections after mounting should be within the range of the conditions determined in the specifications.
If overheated, a short circuit, performance deterioration, or lifespan shortening may occur.
When embedding a printed circuit board where a chip is mounted to a set, be sure that residual stress is not given to the chip due to
the overall distortion of the printed circuit board and partial distortion such as at screw tightening portions.
Self heating (temperature increase) occurs when the power is turned ON, so the tolerance should be sufficient for the set thermal
design.
Carefully lay out the coil for the circuit board design of the non-magnetic shield type.
A malfunction may occur due to magnetic interference.
Use a wrist band to discharge static electricity in your body through the grounding wire.
Do not expose the products to magnets or magnetic fields.
Do not use for a purpose outside of the contents regulated in the delivery specifications.
The products listed on this catalog are intended for use in general electronic equipment (AV equipment, telecommunications equip-
ment, home appliances, amusement equipment, computer equipment, personal equipment, office equipment, measurement equip-
ment, industrial robots) under a normal operation and use condition.
The products are not designed or warranted to meet the requirements of the applications listed below, whose performance and/or qual-
ity require a more stringent level of safety or reliability, or whose failure, malfunction or trouble could cause serious damage to society,
person or property.
If you intend to use the products in the applications listed below or if you have special requirements exceeding the range or conditions
set forth in the each catalog, please contact us.
(1) Aerospace/aviation equipment
(2) Transportation equipment (cars, electric trains, ships, etc.)
(3) Medical equipment
(4) Power-generation control equipment
(5) Atomic energy-related equipment  
(6) Seabed equipment
(7) Transportation control equipment
(8) Public information-processing equipment
(9) Military equipment
(10) Electric heating apparatus, burning equipment
(11) Disaster prevention/crime prevention equipment
(12) Safety equipment
(13) Other applications that are not considered general-purpose
applications
When designing your equipment even for general-purpose applications, you are kindly requested to take into consideration securing pro-
tection circuit/device or providing backup circuits in your equipment.
REMINDERS
(3/11)
20180521 / beads_commercial_signal_mmz0603-e_en.fm
Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use.
Please note that the contents may change without any prior notice due to reasons such as upgrading.
EMC Components
Chip beads
For general signal line
GHz noise countermeasure (general signal line, high-speed line)
FEATURES
Noise reduction solution for general signal line.
Compared to the MMZ series, it is a product that increases the SRF to GHz bands and can countermeasure nose at wide frequencies
with 1 element.
Compared to the MMZ series, it can attain high impedance at GHz bands.
Various frequency characteristics with 4 materials of different features for countermeasures against everything from general signals to
high-speed signals.
APPLICATION
Noise removal for mobile devices such as smartphones and tablet terminals, and various modules.
Noise removal for PCs and recorders, household appliances such as STBs, smart grids, and industrial equipment.
PART NUMBER CONSTRUCTION
OPERATING TEMPERATURE RANGE, PACKAGE QUANTITY, PRODUCT WEIGHT
The storage temperature range is for after the circuit board is mounted.
Overview of MMZ0603-E type
MMZ 0603 S 121 E T 000
Series name L×W×T dimensions Material name Impedance Characteristic
type Packaging style Internal code
(mm) () at 100MHz
0603 0.6×0.3x0.3 S 121 120 E T Taping 000
A 102 1000
D
F
Type
Temperature ranges Package quantity Individual weight
Operating
temperature
°C
Storage
temperature
°C(pieces/reel) mg
MMZ0603-E –55 to +125 –55 to +125 15,000 0.3
Product compatible with RoHS directive
Halogen-free
Compatible with lead-free solders
RoHS Directive Compliant Product: See the following for more details.https://product.tdk.com/info/en/environment/rohs/index.html
Halogen-free: indicates that Cl content is less than 900ppm, Br content is less than 900ppm, and that the total Cl and Br content is less than 1500ppm.
(4/11)
20180521 / beads_commercial_signal_mmz0603-e_en.fm
Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use.
Please note that the contents may change without any prior notice due to reasons such as upgrading.
EMC Components
MMZ0603-E type
RECOMMENDED REFLOW PROFILE
Preheating Soldering Peak
Temp. Time Temp. Time Temp. Time
T1 T2 t1 T3 t2 T4 t3
150°C 180°C 60 to 120s 230°C 30 to 60s 250 to 260°C 10s
Natural
cooling
t3
t1
Preheating
t2
Soldering
T3 T3
T4
T2
T1
t: Time
Peak
T: Temperature
(5/11)
20180521 / beads_commercial_signal_mmz0603-e_en.fm
Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use.
Please note that the contents may change without any prior notice due to reasons such as upgrading.
EMC Components
MMZ0603-E type
MATERIAL CHARACTERISTIC
S material: Standard type that features impedance characteristics similar to those of a typical ferrite core. For signal line applications in
which the blocking region is near 100MHz. Impedance values selected for effectiveness at 40 to 300MHz.
A material: This high-impedance product is based on the impedance frequency characteristics of our Y-material. The product offers
excellent impedance characteristics, which is greater than 2500, in the vicinity of 100MHz range (MMZ1608A252B).
D material: For applications calling for low insertion loss at low frequencies and sharply increasing impedance at high frequencies.
Designed for high impedance at high frequencies (00MHz to 1GHz) for signal line applications.
F material: This new product inherits the characteristic of our D-material, namely its sharp impedance rise time, and its impedance peak
frequency has been shifted higher into range. The product offers excellent noise suppression from 600MHz to as high as in
the GHz range.
TYPICAL MATERIAL IMPEDANCE CHARACTERISTICS
0
500
1000
1500
2000
2500
10 100 1000
Frequency(MHz)
S
ADF
(6/11)
20180521 / beads_commercial_signal_mmz0603-e_en.fm
Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use.
Please note that the contents may change without any prior notice due to reasons such as upgrading.
EMC Components
MMZ0603-E type
SHAPE & DIMENSIONS
RECOMMENDED LAND PATTERN
Dimensions in mm
0.3±0.03
0.6±0.03
0.1min.
0.3±0.03
Dimensions in mm
0.30 0.250.25
0.30
(7/11)
20180521 / beads_commercial_signal_mmz0603-e_en.fm
Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use.
Please note that the contents may change without any prior notice due to reasons such as upgrading.
EMC Components
MMZ0603-E type
ELECTRICAL CHARACTERISTICS
CHARACTERISTICS SPECIFICATION TABLE
Measurement equipment
Equivalent measurement equipment may be used.
Impedance DC resistance Rated current Part No.
[100MHz] [1GHz]
()Tolerance ()Tolerance ()max. (mA)max.
120 ±25% 200 ±40% 0.37 250 MMZ0603S121ET000
240 ±25% 400 ±40% 0.71 200 MMZ0603S241ET000
600 ±25% 1000 ±40% 1.60 150 MMZ0603S601ET000
1000 ±25% 1800 ±40% 2.60 125 MMZ0603S102ET000
120 ±25% 300 ±40% 0.44 250 MMZ0603A121ET000
240 ±25% 600 ±40% 0.86 200 MMZ0603A241ET000
330 ±25% 750 ±40% 1.00 220 MMZ0603A331ET000
470 ±25% 1000 ±40% 1.30 185 MMZ0603A471ET000
600 ±25% 1500 ±40% 1.70 160 MMZ0603A601ET000
1000 ±25% 2300 ±40% 2.90 130 MMZ0603A102ET000
33 ±25% 200 ±40% 0.6 250 MMZ0603D330ET000
47 ±25% 300 ±40% 0.76 200 MMZ0603D470ET000
120 ±25% 1000 ±40% 2.4 125 MMZ0603D121ET000
160 ±25% 1400 ±40% 2.90 125 MMZ0603D161ET000
56 ±25% 700 ±40% 1.9 150 MMZ0603F560ET000
75 ±25% 950 ±40% 2.6 125 MMZ0603F750ET000
Measurement item Product No. Manufacturer
Impedance E4991A+16197 Keysight Technologies
DC resistance Type-7556 Yokogawa
(8/11)
20180521 / beads_commercial_signal_mmz0603-e_en.fm
Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use.
Please note that the contents may change without any prior notice due to reasons such as upgrading.
EMC Components
MMZ0603-Eタイプ
ELECTRICAL CHARACTERISTICS
Z VS. FREQUENCY CHARACTERISTICS (BY SERIES)
MMZ0603S-E series MMZ0603A-E series MMZ0603D-E series
MMZ0603F-E series
10000100010010
0
Impedance (Ω)
500
1000
1500
2000
2500
3000
1
Frequency (MHz)
MMZ0603A102E
MMZ0603A601E
MMZ0603A471E
MMZ0603A331E
MMZ0603A121E
MMZ0603241E
100001000100101
Frequency(MHz)
Impedance(Ω)
0
200
400
600
800
1000
1200
1400
1600
1800
2000
MMZ0603D161E
MMZ0603D121E
MMZ0603D470E
MMZ0603D330E
100001000100101
Frequency(MHz)
Impedance(Ω)
0
500
1000
1500
2000
2500
MMZ0603F750E
MMZ0603F560E
(9/11)
20180521 / beads_commercial_signal_mmz0603-e_en.fm
Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use.
Please note that the contents may change without any prior notice due to reasons such as upgrading.
EMC Components
MMZ0603-E type
ELECTRICAL CHARACTERISTICS
Z, X, R VS. FREQUENCY CHARACTERISTICS
MMZ0603S121ET000 MMZ0603S241ET000 MMZ0603S601ET000
MMZ0603S102ET000 MMZ0603A121ET000 MMZ0603A241ET000
MMZ0603A331ET000 MMZ0603A471ET000 MMZ0603A601ET000
MMZ0603A102ET000 MMZ0603D330ET000 MMZ0603D470ET000
MMZ0603D121ET000 MMZ0603F560ET000 MMZ0603F750ET000
1 10 100 1000 10000
Z
X
R
200
0
400
600
800
1000
1200
Frequency (MHz)
Impedance (Ω)
0
50
100
150
200
250
1 10 100 1000 10000
Frequency (MHz)
Impedance (Ω)
Z
R
X
01 10 100 1000 10000
Frequency (MHz)
Impedance (Ω)
50
100
150
200
250
300
350
400
450
Z
R
X
1 10 100 1000 10000
Z
R
0
200
400
600
800
1000
2000
1200
1400
1600
1800
X
Frequency (MHz)
Impedance (Ω)
01 10 100 1000 10000
Frequency (MHz)
Impedance (Ω)
50
100
150
200
250
300
350
ZR
X
01 10 100 1000 10000
Frequency (MHz)
Impedance (Ω)
100
200
300
400
500
600
700
800
ZR
X
1 10 100 1000 10000
0
Frequency (MHz)
Impedance (Ω)
200
400
600
800
1000
1200
1400
1600
Z
R
X
1 10 100 1000 10000
0
Frequency (MHz)
Impedance (Ω)
200
400
600
800
1000
1200
1400
Z
R
X
1 10 100 1000 10000
0
Frequency (MHz)
Impedance (Ω)
200
400
600
800
1000
Z
R
X
01 10 100 1000 10000
Frequency (MHz)
Impedance (Ω)
50
100
150
200
250
300
350
400
450
500
ZR
X
01 10 100 1000 10000
Frequency (MHz)
Impedance (Ω)
50
100
150
200
250
300
350
Z
R
X
1 10 100 1000 10000
0
Frequency (MHz)
Impedance (Ω)
500
1000
1500
2000
2500
3000
Z
R
X
01 10 100 1000 10000
Frequency (MHz)
Impedance (Ω)
500
1000
1500
2000
2500
ZR
X
01 10 100 1000 10000
Frequency (MHz)
Impedance (Ω)
200
400
600
800
1000
1200
1400
1600
ZR
X
01 10 100 1000 10000
Frequency (MHz)
Impedance (Ω)
200
400
600
800
1000
1200
1400
1600
1800
2000
ZR
X
(10/11)
20180521 / beads_commercial_signal_mmz0603-e_en.fm
Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use.
Please note that the contents may change without any prior notice due to reasons such as upgrading.
EMC Components
MMZ0603-E type
ELECTRICAL CHARACTERISTICS
Z, X, R VS. FREQUENCY CHARACTERISTICS
MMZ0603D161ET000
1 10 100 1000 10000
0
200
400
600
800
1000
2000
1200
1400
1600
1800
Frequency (MHz)
Impedance (Ω)
ZR
X
(11/11)
20180521 / beads_commercial_signal_mmz0603-e_en.fm
Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use.
Please note that the contents may change without any prior notice due to reasons such as upgrading.
EMC Components
MMZ0603-E type
PACKAGING STYLE
REEL DIMENSIONS
TAPE DIMENSIONS
Dimensions in mm
Ty p e A B P1 K
MMZ0603-E 0.38±0.05 0.68±0.05 2.0±0.05 0.5max.
ø180±2.0
2.0±0.5
ø13±0.2
ø21±0.8
Dimensions in mm
1.0
ø60min.
14.4max.
8.4 +2.0
–0.0
4.0±0.12.0±0.05
B
A P1
8.0±0.3
1.75±0.1
3.5±0.05
K
1.5 +0.1
0
160min. Taping 200min.
300min.
Drawing direction
Dimensions in mm