THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION
CURRENT REV DESC: REVISED
EC NO: 601573
DRWN:
AISHII
2018/07/17
CHK'D:
TRSUZUKI
2018/08/10
APPR:
INITIAL REVISION:
DRWN:
NASANUMA
2012/09/21
APPR:
KMORIKAWA
2013/03/15
THIRD ANGLE PROJECTION
DRAWING SERIES
A3-SIZE
52207
DIMENSION UNITS
SCALE
mm
8:1
GENERAL TOLERANCES
(UNLESS SPECIFIED)
ANGULAR TOL
±
3.0 °
4 PLACES
±
0.2
3 PLACES
±
0.25
2 PLACES
±
0.3
1 PLACE
±
0 PLACES
±
DRAFT WHERE APPLICABLE
MUST REMAIN
WITHIN DIMENSIONS
1.0 MM FPC CONN. ZIF R/A
HOUSING ASSY (UPPER CONTACT)
PRODUCT CUSTOMER DRAWING
DOCUMENT NUMBER
DOC TYPE
DOC PART
REVISION
SD-52207-069
PSD
001
D
MATERIAL NUMBER CUSTOMER SHEET NUMBER
SEE TABLE GENERAL MARKET 1 OF 2
FORMAT: master-tb-prod-A3
REVISION: H
DATE: 2018/01/18
DOCUMENT STATUS RV RELEASE DATE
PRE-RELEASE
REFERENCE
USE ONLY
6
5
注記（NOTE)：
6
3
5
1．材質 MATERIAL
ハウジング：ポリアミド（PA），ナチュラル（白色），ガラス充填，UL94V-0
HOUSING:POLYAMIDE, NATURAL(WHITE), GLASS FILLED, UL94V-0
アクチュエータ：ポリフェニレンサルファイド(PPS)，ナチュラル（茶色），ガラス充填，UL94-V0
ACTUATOR:POLYPHENYLENE SULFIDE, NATURAL(BROWN), GLASS FILLED, UL94V-0
ターミナル：リン青銅（t=0.32)
TERMINAL:PHOSPHOR BRONZE(t=0.32)
ネイル(補強金具）：リン青銅（t=0.25)
FITTING NAIL:PHOSPHOR BRONZE(t=0.25)
2．めっき仕様 PLATING
ターミナル TERMINAL
錫銀ビスマスめっき（1.0μm以上）
TIN SILVER BISMUTH PLATING (1.0 MICROMETER MINIMUM)
下地：ニッケルめっき（1.0μm以上）
UNDER PLATE:NICKEL PLATING (1.0 MICROMETER MINIMUM)
ネイル（補強金具） FITTING NAIL
錫めっき（1.0μm以上）
TIN PLATING (1.0 MICROMETER MINIMUM)
下地：ニッケルめっき（1.0μm以上）
UNDER PLATE:NICKEL PLATING (1.0 MICROMETER MINIMUM
．C0.3はFPC/FFCの導体部にかからないこと
C0.3 MUST NOT BE OVERLAPED TO PATTERN OF FPC/FFC.
4．エンボステープ梱包時は、アクチュエータがロックした状態とする。
IN THE PACKAGE, ACTUATOR SHOULD BE LOCKED.
． パターン剥離止め用金具
FITTTING NAIL FOR PREVENTION OF PEELING OF P.C.B. PATTERN.
．ソルダーテール半田付け面、及び金具半田付け面の平坦度：0.15mm MAX.
COPLANARITY OF SOLDER TAILS AND FITTING NAILS
TO BE 0.15mm MAX.
7．ELV及びRoHS適合品
ELV AND RoHS COMPLIANT
GENERAL TOLERANCES
(UNLESS SPECIFIED)
10 UNDER ± 0.2
10 OVER 30 UNDER ± 0.25
30 OVER ± 0.3
ANGULAR ± 3 °
DRAFT WHERE APPLICABLE
MUST REMAIN
WITHIN DIMENSIONS
38.7 35.2 33 52207-3433 34
34.7 31.2 29 52207-3033 30
33.7 30.2 28 52207-2933 29
32.7 29.2 27 52207-2833 28
31.7 28.2 26 52207-2733 27
30.7 27.2 25 52207-2633 26
29.7 26.2 24 52207-2533 25
28.7 25.2 23 52207-2433 24
27.7 24.2 22 52207-2333 23
26.7 23.2 21 52207-2233 22
25.7 22.2 20 52207-2133 21
24.7 21.2 19 52207-2033 20
23.7 20.2 18 52207-1933 19
22.7 19.2 17 52207-1833 18
21.7 18.2 16 52207-1733 17
20.7 17.2 15 52207-1633 16
19.7 16.2 14 52207-1533 15
18.7 15.2 13 52207-1433 14
17.7 14.2 12 52207-1333 13
16.7 13.2 11 52207-1233 12
15.7 12.2 10 52207-1133 11
14.7 11.2 9 52207-1033 10
13.7 10.2 8 52207-0933 9
12.7 9.2 752207-0833 8
11.7 8.2 6 52207-0733 7
10.7 7.2 552207-0633 6
9.7 6.2 452207-0533 5
8.7 5.2 3 52207-0433 4
7.7 4.2 2 52207-0333 3
CBAEMBOSSED PACKAGE ORDER NO.
オーダー番号
極数
CKT.
CONNECTOR SERIES NO.: 52207-**22
1
A
1
A
2
B
2
B
3
C
3
C
4
D
4
D
5
E
5
E
6
F
6
F
7
7
8
8
9
9
10
10
適合FPC/FFC推奨寸法
マスク厚 ：100μm
マスク開口率 ：100%
パターン書き込み禁止エリア
(マウント面）
推奨基板レイアウト
(MOUNT SIDE)
APPLICABLE FPC/FFC
RECOMMENDED DIMENSION
RECOMMENDED P.C.BOARD
PATTERN DIMENSION.(REF.)
NO FOOT PRINT AREA
SCREEN THICKNESS :100 MICROMETER
SCREEN OPEN RATIO :100%
3
PRE-RELEASE
REFERENCE
USE ONLY
DOCUMENT STATUS RV RELEASE DATE
FORMAT: master-tb-prod-A3
REVISION: H
DATE: 2018/01/18
THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION
CURRENT REV DESC: REVISED
EC NO: 601573
DRWN:
AISHII
2018/07/17
CHK'D:
TRSUZUKI
2018/08/10
APPR:
INITIAL REVISION:
DRWN:
NASANUMA
2012/09/21
APPR:
KMORIKAWA
2013/03/15
THIRD ANGLE PROJECTION
DRAWING SERIES
A3-SIZE
52207
DIMENSION UNITS
SCALE
mm
5:1
GENERAL TOLERANCES
(UNLESS SPECIFIED)
ANGULAR TOL
±
3.0 °
4 PLACES
±
0.2
3 PLACES
±
0.25
2 PLACES
±
0.3
1 PLACE
±
0 PLACES
±
DRAFT WHERE APPLICABLE
MUST REMAIN
WITHIN DIMENSIONS
1.0 MM FPC CONN. ZIF R/A
HOUSING ASSY (UPPER CONTACT)
PRODUCT CUSTOMER DRAWING
DOCUMENT NUMBER
DOC TYPE
DOC PART
REVISION
SD-52207-069
PSD
001
D
MATERIAL NUMBER CUSTOMER SHEET NUMBER
SEE TABLE GENERAL MARKET 2 OF 2
0.3
±
0.05
補強板：ポリイミド
REINFORCE BOARD: POLYMIDE
仕上がり厚さ
THICKNESS
めっき：錫めっき(0.5-1.2μm)
下地ニッケル(1-5μm)
PLATING: TIN(0.5-1.2μm)
NICKEL UNDER(1-5μm)
導体部： 銅箔(35 or 50μm)
COPPER FOIL (35 or 50μm)
接着剤(難燃ポリエステル系)
ADHESIVE（FLAME-RETARDANT
POLYESTER ADHESIVE)
接着剤(難燃ポリエステル系)
ADHESIVE（FLAME-RETARDANT
POLYESTER ADHESIVE)
絶縁テープ：ポリエステル系(25μm)
INSULATING FILM: PET(25μm)
絶縁テープ：ポリエステル系(25μm)
INSULATING FILM: PET(25μm)
0.3
±
0.05
仕上がり厚さ
THICKNESS
接着剤(難燃ポリエステル系)
ADHESIVE（FLAME-RETARDANT
POLYESTER ADHESIVE)
補強板：ポリエステル系
REINFORCE BOARD: PET
カバーレイ : ポリイミド(25μm)
COVER FILM: POLYIMIDE(25μm)
熱硬化接着剤
THERMOSETTING ADHESIVE
ベースフィルム：ポリイミド(25μm)
BASE FILM: POLYIMIDE(25μm)
熱硬化接着剤
THERMOSETTING ADHESIVE
めっき：錫めっき(0.5-1.2μm)
下地ニッケル(1-5μm)
PLATING: TIN(0.5-1.2μm)
NICKEL UNDER(1-5μm)
導体部： 銅箔(35 or 50μm)
COPPER FOIL (35 or 50μm)
熱硬化接着剤
THERMOSETTING ADHESIVE
FFC構成推奨仕様
RECOMMENDED STRUCTURE OF FFC
FPC構成推奨仕様
RECOMMENDED STRUCTURE OF FPC
FPC/FFCについて：
抜き方向は、導体側から補強板側を推奨致します。
尚、接着剤の接点部への付着は導通不良の原因になりますので、
染み出しが無い様お願い致します。
ABOUT FPC/FFC:
RECOMMENDED PUNCHER DIRECTION:
FROM CONDUCTOR SIDE TO STIFFNER SIDE
PLEASE PUT APPROPRIATE AMOUNT OF ADHESIVE ON ADHEREND
BECAUSE THERE IS A POSSIBILITY THAT THE EXTRA ADHESIVE
CAUSES THE DEFECT IN ELECTRICAL CONTINUITY.
GENERAL TOLERANCES
(UNLESS SPECIFIED)
10 UNDER ± 0.2
10 OVER 30 UNDER ± 0.25
30 OVER ± 0.3
ANGULAR ± 3 °
DRAFT WHERE APPLICABLE
MUST REMAIN
WITHIN DIMENSIONS
1
A
1
A
2
B
2
B
3
C
3
C
4
D
4
D
5
E
5
E
6
F
6
F
7
7
8
8
9
9
10
10
