LTC1731-4.1/LTC1731-4.2 Single Cell Lithium-Ion Linear Battery Charger Controllers U FEATURES DESCRIPTIO The LTC (R)1731 is a complete constant-current/constantvoltage linear charger controller for single cell lithium-ion batteries. Nickel-cadmium (NiCd) and nickel-metal-hydride (NiMH) batteries can also be charged with constant current using external termination. The external sense resistor sets the charge current with 5% accuracy. An internal resistor divider and precision reference set the final float potential with 1% accuracy. The output float voltage is set internally to 4.1V (LTC1731-4.1) or 4.2V (LTC1731-4.2). Complete Linear Charger Controller for 1-Cell Lithium-Ion Batteries 1% Voltage Accuracy Programmable Charge Current C/10 Charge Current Detection Output Programmable Charge Termination Timer Space Saving 8-Pin MSOP Package Automatic Sleep Mode When Input Supply is Removed (7A Battery Drain) Automatic Trickle Charging of Low Voltage Cells Programmable for Constant-Current-Only Mode When the input supply is removed, the LTC1731 automatically enters a low current sleep mode, dropping the battery drain current to typically 7A. An internal comparator detects the end-of-charge (C/10) condition while a programmable timer, using an external capacitor, sets the total charge time. Fully discharged cells are automatically trickle charged at 10% of the programmed current until cell voltage exceeds 2.457V. U APPLICATIO S Cellular Phones Handheld Computers Charging Docks and Cradles Programmable Current Source The LTC1731 is available in the 8-pin MSOP and SO packages. , LTC and LT are registered trademarks of Linear Technology Corporation. U TYPICAL APPLICATIO 500mA Li-Ion Battery Charger VIN = 6V MBRM120T3 7 1k CHARGE STATUS VCC SENSE 2 DRV CHRG RSENSE 0.2 8 6 Q1 Si9430DY LTC1731-4.2 3 CTIMER 0.1F TIMER BAT PROG GND 4 1F IBAT = 500mA 1 5 RPROG* 19.6k + Li-ION 10F CELL 1731 TA01 *SHUTDOWN INVOKED BY FLOATING THE PROG PIN 1 LTC1731-4.1/LTC1731-4.2 W W U W ABSOLUTE MAXIMUM RATINGS (Note 1) Input Supply Voltage (VCC) ................................... 13.2V Input Voltage (SENSE, DRV, BAT, TIMER, PROG) .................................. - 0.3V to 13.2V Output Voltage (CHRG) ......................... - 0.3V to 13.2V Operating Temperature Range (Note 2) .....- 40 to 85C Storage Temperature Range ................. - 65C to 150C Lead Temperature (Soldering, 10 sec).................. 300C U W U PACKAGE/ORDER INFORMATION ORDER PART NUMBER TOP VIEW BAT CHRG TIMER GND 1 2 3 4 8 7 6 5 SENSE VCC DRV PROG LTC1731EMS8-4.1 LTC1731EMS8-4.2 MS8 PACKAGE 8-LEAD PLASTIC MSOP MS8 PART MARKING TJMAX = 150C, JA = 200C/W LTJK LTKQ ORDER PART NUMBER TOP VIEW BAT 1 8 SENSE CHRG 2 7 VCC TIMER 3 6 DRV GND 4 5 PROG LTC1731ES8-4.1 LTC1731ES8-4.2 S8 PART MARKING S8 PACKAGE 8-LEAD PLASTIC SO 173141 173142 TJMAX = 150C, JA = 125C/W Consult factory for parts specified with wider operating temperature ranges. ELECTRICAL CHARACTERISTICS The denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25C. VCC = 6V unless otherwise noted. SYMBOL PARAMETER CONDITIONS MIN VCC Input Supply Voltage ICC Input Supply Current Charger On, Current Mode Shutdown Mode Sleep Mode (Battery Drain Current) VBAT Regulated Output Voltage LTC1731-4.1 (5V VCC 12V) LTC1731-4.2 (5V VCC 12V) IBAT Current Mode Charge Current RPROG = 19.6k, RSENSE = 0.2 RPROG = 19.6k, RSENSE = 0.2 RPROG = 97.6k, RSENSE = 0.2 TYP UNITS 12 V 1 1 7 3 2 20 mA mA A 4.059 4.158 4.1 4.2 4.141 4.242 465 415 70 500 mA mA mA 4.5 MAX V V 100 535 585 130 ITRIKL Trickle Charge Current VBAT = 2V, RPROG = 19.6k, ITRIKL = (VCC - VSENSE)/0.2 30 50 100 mA VTRIKL Trickle Charge Threshold Voltage From Low to High 2.35 2.457 2.55 V VUV VCC Undervoltage Lockout Voltage From Low to High 4.1 4.5 VUV VCC Undervoltage Lockout Hysteresis VMSD Manual Shutdown Threshold Voltage 2 200 PROG Pin Low to High PROG Pin High to Low 2.457 2.446 V mV V V LTC1731-4.1/LTC1731-4.2 ELECTRICAL CHARACTERISTICS The denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25C. VCC = 6V unless otherwise noted. SYMBOL PARAMETER CONDITIONS VASD Automatic Shutdown Threshold Voltage (VCC - VBAT) High to Low (VCC - VBAT) Low to High MIN TYP MAX UNITS 30 40 54 69 90 100 mV mV VDIS Voltage Mode Disable Threshold Voltage VDIS = VCC - VTIMER 0.4 V IPROG PROG Pin Current Internal Pull-Up Current, No RPROG PROG Pin Load Regulation PROG Pin Source Current, VPROG 5mV VPROG PROG Pin Voltage RPROG =19.6k ICHRG CHRG Pin Weak Pull-Down Current VCHRG = 1V VCHRG CHRG Pin Output Low Voltage ICHRG = 5mA IC/10 End of Charge Indication Current Level RPROG = 19.6k, RSENSE = 0.2 tTIMER TIMER Accuracy CTIMER = 0.1F 10 % VCLAMP DRV Pin Clamp Voltage VCLAMP = VCC - VDRV, IDRIVE = 50A 6.5 V A 2.5 A 300 2.457 50 Note 1: Absolute Maximum Ratings are those values beyond which the life of a device may be impaired. 25 V 100 150 A 0.6 1.2 V 50 100 mA Note 2: The LTC1731E is guaranteed to meet performance specifications from 0C to 70C. Specifications over the - 40C to 85C operating temperature range are assured by design, characterization and correlation with statistical process controls. Guaranteed I grade parts are available, consult factory. U W TYPICAL PERFOR A CE CHARACTERISTICS Program Pin Voltage vs Temperature Trickle Charge Current vs Input Supply RPROG = 19.6k RSENSE = 0.2 VBAT = 2V TA = 25C 50 45 40 Timer Accuracy vs Temperature 110 VCC = 6V RPROG = 19.6k 2.465 VPROG (V) 55 ITRKL (mA) 2.470 2.460 2.455 4 6 8 10 12 VCC (V) 1731 G01 2.450 -50 -25 VCC = 6V CTIMER = 0.1F 105 tTIMER (%) 60 100 95 0 25 50 75 100 125 150 TEMPERATURE (C) 1731 G02 90 -50 -25 0 25 50 75 100 125 150 TEMPERATURE (C) 1731 G03 3 LTC1731-4.1/LTC1731-4.2 U W TYPICAL PERFOR A CE CHARACTERISTICS Trickle Charge Threshold Voltage vs Temperature 110 VCC = 6V 2.460 2.455 2.450 -50 -25 RPROG = 19.6k RSENSE = 0.2 VBAT = 2V 55 VCC = 6V 105 tTIMER (%) VTRKL (V) 2.465 60 VBAT = 3V CTIMER = 0.1F TA = 25C ITRKL (mA) 2.470 Trickle Charge Current vs Temperature Timer Accuracy vs Input Supply 100 95 0 90 25 50 75 100 125 150 TEMPERATURE (C) 45 4 6 8 1731 G06 Trickle Charge Threshold Voltage vs Input Supply 2.480 RPROG = 19.6k 2.475 TA = 25C RPROG = 19.6k 530 RSENSE = 0.2 VBAT = 3V 520 VCC = 6V 2.470 VTRKL (V) 510 500 2.465 2.460 490 2.455 480 2.450 470 2.445 2.440 25 50 75 100 125 150 TEMPERATURE (C) 4 6 8 10 1731 G08 Program Pin Voltage vs Input Supply Battery Charge Current vs Input Supply 2.480 520 2.470 RPROG = 19.6k 515 RSENSE = 0.2 VBAT = 3V 510 TA = 25C 2.465 505 IBAT (mA) VPROG (V) RPROG = 19.6k 2.475 VBAT = 3V TA = 25C 2.460 495 2.450 490 2.445 485 6 8 10 12 VCC (V) 480 4 6 8 10 12 VCC (V) 1731 G09 4 500 2.455 4 12 VCC (V) 1731 G07 2.440 25 50 75 100 125 150 TEMPERATURE (C) 1731 G05 540 IBAT (mA) 0 VCC (V) Battery Charge Current vs Temperature 0 40 -50 -25 12 10 1731 G04 460 -50 -25 50 1731 G10 LTC1731-4.1/LTC1731-4.2 U U U PIN FUNCTIONS BAT (Pin 1): Battery Sense Input. A bypass capacitor of at least 10F is required to keep the loop stable when the battery is not connected. A precision internal resistor divider sets the final float potential on this pin. The resistor divider is disconnected in sleep mode. CHRG (Pin 2): Open-Drain Charge Status Output. When the battery is being charged, the CHRG pin is pulled low by an internal N-channel MOSFET. When the charge current drops to 10% of the full-scale current for at least 0.32 seconds, the N-channel MOSFET turns off and a 100A current source is connected from the CHRG pin to GND. When the timer runs out or the input supply is removed, the current source will be disconnected and the CHRG pin is forced into a high impedance state. TIMER (Pin 3): Timer Capacitor and Constant-Voltage Mode Disable Input Pin. The timer period is set by placing a capacitor, CTIMER, to GND. The timer period is tTIMER = (CTIMER * 3 hours)/(0.1F). When the TIMER pin is connected to VCC, the constant-voltage mode and the timer are disabled, the chip will operate in constantcurrent mode only. Short the TIMER pin to GND to disable the internal timer function and the C/10 function. GND (Pin 4): Ground Connection. PROG (Pin 5): Charge Current Program and Shutdown Input Pin. The charge current is programmed by connecting a resistor, RPROG to ground. The charge current is IBAT = (VPROG * 800)/(RPROG * RSENSE). The IC can be forced into shutdown by floating the PROG pin. An internal 2.5A current source will pull the pin above the shutdown threshold voltage when the program resistor (RPROG) is disconnected. DRV (Pin 6): Drive Output Pin for the P-Channel MOSFET or PNP Transistor. The impedance is high at this pin, therefore, a high beta PNP pass transistor should be used. The DRV pin is internally clamped to 6.5V below VCC. VCC (Pin 7): Positive Input Supply Voltage. When VBAT is within 54mV of VCC, the LTC1731 is forced into sleep mode, dropping ICC to 7A. VCC ranges from 4.5V to 12V. Bypass this pin with a 1F capacitor. SENSE (Pin 8): Current Sense Input. A sense resistor, RSENSE, must be connected from VCC to the SENSE pin. This resistor is chosen using the following equation: RSENSE = (VPROG * 800)/(RPROG * IBAT) 5 LTC1731-4.1/LTC1731-4.2 W BLOCK DIAGRA VCC 7 RSENSE SENSE + 80 C1 2 + - 800 - CHRG 8 54mV + C4 - - C/10 STOP C/10 TIMER + DRV CA SLP OSCILLATOR BAT - SHDN 3 720 LOGIC LBO COUNTER 6 1 C2 + 100A VREF - + - VA VCC A1 - + + C3 2.5A VREF 2.457V CHARGE 5 BATTERY CURRENT IBAT = (2.457V * 800)/(RPROG * RSENSE) 6 PROG RPROG GND 4 1731 BD LTC1731-4.1/LTC1731-4.2 U OPERATIO The LTC1731 is a linear battery charger controller for single cell lithium-ion batteries. The charge current is programmed by the combination of a program resistor (RPROG) from the PROG pin to ground and a sense resistor (RSENSE) between the VCC and SENSE pins. RPROG sets a program current through an internal trimmed 800 resistor setting up a voltage drop from VCC to the input of the current amplifier (CA). The current amplifier servos the gate of the external P-channel MOSFET to force the same voltage drop across RSENSE which sets the charge current. When the potential at the BAT pin approaches the preset float voltage, the voltage amplifier (VA) will start sinking current which shrinks the voltage drop across RSENSE, thus reducing the charge current. Charging begins when the potential at VCC pin rises above the UVLO level and a program resistor is connected from the PROG pin to ground. At the beginning of the charge cycle, if the battery voltage is below 2.457V, the charger goes into trickle charge mode. The trickle charge current is 10% of the full-scale current. If the cell voltage stays low for one quarter of the total charge time, the charge sequence will be terminated. The charger goes into the fast charge constant-current mode after the voltage on the BAT pin rises above 2.457V. In constant-current mode, the charge current is set by the combination of RSENSE and RPROG. When the battery approaches the final float voltage, the charge current will begin to decrease. When the current drops to 10% of the full-scale charge current, an internal comparator will turn off the pull-down N-channel MOSFET at the CHRG pin and connect a weak current source to ground to indicate an end-of-charge (C/10) condition. An external capacitor on the TIMER pin sets the total charge time. After a time-out occurs, the charging will be terminated and the CHRG pin is forced to a high impedance state. To restart the charge cycle, simply remove the input voltage and reapply it, or float the PROG pin momentarily. For batteries like lithium-ion that require accurate final float potential, the internal 2.457V reference, voltage amplifier and the resistor divider provide regulation with 1% (max) accuracy. For NiMH and NiCd batteries, the LTC1731 can be turned into a current source by pulling the TIMER pin to VCC. When in the constant-current only mode, the voltage amplifier, timer and the trickle charge function are all disabled. The charger can be shut down by floating the PROG pin (ICC = 1mA). An internal current source will pull it high and clamp at 3.5V. When the input voltage is not present, the charger goes into a sleep mode, dropping ICC to 7A. This greatly reduces the current drain on the battery and increases the standby time. U W U U APPLICATIONS INFORMATION Charge Termination Trickle Charge and Defective Battery Detection The charger is off when any of the following conditions exist: the voltage at the VCC pin is below 4.1V, the voltage at the VCC pin is higher than 4.1V but is less than 54mV above VBAT, or the PROG pin is floating. The DRV pin will be pulled to VCC and the internal resistor divider is disconnected to reduce the current drain on the battery. At the beginning of the charging sequence, if the battery voltage is low (below 2.457V) the charger goes into trickle charge mode. The charge current is set to 10% of the fullscale current. If the low cell voltage persists for one quarter of the total charging time, the battery is considered defective, charging will be terminated and the CHRG pin output is forced to a high impedance state. Undervoltage Lockout (UVLO) An internal undervoltage lockout circuit monitors the input voltage and keeps the charger in shutdown mode until VCC rises above 4.1V. To prevent oscillation around VCC = 4.1V, the UVLO circuit has built-in hysteresis. Shutdown The LTC1731 can be forced into shutdown by floating the PROG pin and allowing the internal 2.5A current source to pull the pin above the 2.457V shutdown threshold 7 LTC1731-4.1/LTC1731-4.2 U W U U APPLICATIONS INFORMATION V+ voltage. The DRV pin will then be pulled up to VCC and turn off the external P-channel MOSFET. The internal timer is reset in the shutdown mode. VDD 7 VCC 100k LTC1731 Programming Charge Current CHRG 2 OUT The formula for the battery charge current (see Block Diagram) is: IN 1731 F01 Figure 1. Microprocessor Interface IBAT = (IPROG)(800/RSENSE) = (2.457V/RPROG)(800/RSENSE) where RPROG is the total resistance from the PROG pin to ground. For example, if 0.5A charge current is needed, select a value for RSENSE that will drop 100mV at the maximum charge current. RSENSE = 0.1V/0.5A = 0.2, then calculate: RPROG = (2.457V/500mA)(800/0.2) = 19.656k For best stability over temperature and time, 1% resistors are recommended. The closest 1% resistor value is 19.6k. Programming the Timer The programmable timer is used to terminate the charge. The length of the timer is programmed by an external capacitor at the TIMER pin. The total charge time is: Time = (3 Hours)(CTIMER/0.1F) The timer starts when the input voltage greater than 4.1V is applied and the program resistor is connected to ground. After a time-out occurs, the CHRG output will turn into a high impedance state to indicate that the charging has stopped. Connecting the TIMER pin to VCC disables the timer and also puts the charger into a constant-current mode. To only disable the timer function, short the TIMER pin to GND. CHRG Status Output Pin When the charge cycle starts, the CHRG pin is pulled down to ground by an internal N-channel MOSFET that can drive an LED. When the battery current drops to 10% of the fullscale current (C/10), the N-channel MOSFET is turned off and a weak 100A current source to ground is connected to the CHRG pin. After a time-out occurs, the pin will go into a high impedance state. By using two different value 8 PROCESSOR 2k pull-up resistors, a microprocessor can detect three states from this pin (charging, C/10 and stop charging). See Figure 1. When the LTC1731 is in charge mode, the CHRG pin is pulled down by an internal N-channel MOSFET. To detect this mode, force the digital output pin, OUT, high and measure the voltage at the CHRG pin. The N-channel MOSFET will pull the pin low even with a 2k pull-up resistor. Once the charge current drops to 10% of the full-scale current (C/10), the N-channel MOSFET is turned off and a 100A current source is connected to the CHRG pin. The IN pin will then be pulled high by the 2k pull-up. By forcing the OUT pin into a high impedance state, the current source will pull the pin low through the 100k resistor. When the internal timer has expired, the CHRG pin will change to high impedance state and the 100k resistor will then pull the pin high to indicate the charging has stopped. Refer to Table 1 for the summary. Table 1. CHRG Pin Interface with Microprocessor IN OUT STATUS Low High Charging Low Hi-Z Charging High High C/10 Low Hi-Z C/10 High Hi-Z Stop Charging End of Charge (C/10) The LTC1731 includes a comparator to monitor the charge current to detect an end-of-charge condition. When the battery current falls below 10% of full scale, the comparator trips and turns off the N-channel MOSFET at the CHRG pin and switches in a 100A current source to ground. LTC1731-4.1/LTC1731-4.2 U U W U APPLICATIONS INFORMATION After an internal time delay of 320ms, this state is then latched. This delay will help prevent false triggering due to transient currents. The end-of-charge comparator is disabled in trickle charge mode. Gate Drive Typically the LTC1731 controls an external P-channel MOSFET to supply current to the battery. The DRV pin is internally clamped to 6.5V below VCC. This feature allows low voltage P-channel MOSFETs with gate to source breakdown voltage rated at 8V to be used. An external PNP transistor can also be used as the pass transistor instead of the P-channel MOSFET. Due to the low current gain of the current amplifier (CA), a high gain Darlington PNP transistor is required to avoid excessive charge current error. The gain of the current amplifier is around 0.6A/mV. For every 1A of base current, a 1.6mV of gain error shows up at the inputs of CA. With RPROG = 19.6k (100mV across RSENSE), it represents 1.67% of error in charging current. Constant-Current Only Mode The LTC1731 can be used as a programmable current source by forcing the TIMER pin to VCC. This is particularly useful for charging NiMH or NiCd batteries. In the constant-current only mode, the timer and voltage amplifier are both disabled. An external termination method is required to properly terminate the charge. Stability The charger is stable without any compensation when a P-channel MOSFET is used as the pass transistor. However, a 10F capacitor is recommended at the BAT pin to keep the ripple voltage low when the battery is disconnected. When a PNP transistor is chosen as the pass transistor, a 1000pF capacitor is required from the DRV pin to VCC. This capacitor is needed to help stablize the voltage loop. A 10F capacitor at the BAT pin is also recommended when a battery is not present. U TYPICAL APPLICATIO Using CHRG Pin to Indicate Charge Status OPTIONAL: FOR REVERSE INPUT PROTECTION VIN = 6V MMSD4148 MBRM120T3 1.5k MMBT3906 7 20k VCC 4.7k MMBT3906 SENSE CONDITION NO WALL ADAPTER CHARGING (I > C/10) CHARGING (I < C/10) TIMER EXPIRED GREEN AMBER OFF OFF OFF ON ON OFF ON OFF 1k 2.2k 1k 2 DRV CHRG RSENSE 0.2 8 6 1F Si9430DY LTC1731-4.2 3 GREEN AMBER TIMER BAT PROG 0.1F GND 4 1 5 RPROG 19.6k + Li-ION 10F CELL 1731 TA04 9 LTC1731-4.1/LTC1731-4.2 U PACKAGE DESCRIPTIO Dimensions in inches (millimeters) unless otherwise noted. MS8 Package 8-Lead Plastic MSOP (LTC DWG # 05-08-1660) 0.118 0.004* (3.00 0.102) 8 7 6 5 0.118 0.004** (3.00 0.102) 0.193 0.006 (4.90 0.15) 1 2 3 4 0.043 (1.10) MAX 0.007 (0.18) 0 - 6 TYP 0.021 0.006 (0.53 0.015) SEATING PLANE 0.009 - 0.015 (0.22 - 0.38) 0.0256 (0.65) BSC * DIMENSION DOES NOT INCLUDE MOLD FLASH, PROTRUSIONS OR GATE BURRS. MOLD FLASH, PROTRUSIONS OR GATE BURRS SHALL NOT EXCEED 0.006" (0.152mm) PER SIDE ** DIMENSION DOES NOT INCLUDE INTERLEAD FLASH OR PROTRUSIONS. INTERLEAD FLASH OR PROTRUSIONS SHALL NOT EXCEED 0.006" (0.152mm) PER SIDE 10 0.034 (0.86) REF 0.005 0.002 (0.13 0.05) MSOP (MS8) 1100 LTC1731-4.1/LTC1731-4.2 U PACKAGE DESCRIPTIO Dimensions in inches (millimeters) unless otherwise noted. S8 Package 8-Lead Plastic Small Outline (Narrow 0.150) (LTC DWG # 05-08-1610) 0.189 - 0.197* (4.801 - 5.004) 8 7 6 5 0.150 - 0.157** (3.810 - 3.988) 0.228 - 0.244 (5.791 - 6.197) 1 0.010 - 0.020 x 45 (0.254 - 0.508) 0.008 - 0.010 (0.203 - 0.254) 0.053 - 0.069 (1.346 - 1.752) 0- 8 TYP 0.016 - 0.050 (0.406 - 1.270) 0.014 - 0.019 (0.355 - 0.483) TYP *DIMENSION DOES NOT INCLUDE MOLD FLASH. MOLD FLASH SHALL NOT EXCEED 0.006" (0.152mm) PER SIDE **DIMENSION DOES NOT INCLUDE INTERLEAD FLASH. INTERLEAD FLASH SHALL NOT EXCEED 0.010" (0.254mm) PER SIDE 2 3 4 0.004 - 0.010 (0.101 - 0.254) 0.050 (1.270) BSC Information furnished by Linear Technology Corporation is believed to be accurate and reliable. However, no responsibility is assumed for its use. Linear Technology Corporation makes no representation that the interconnection of its circuits as described herein will not infringe on existing patent rights. SO8 1298 11 LTC1731-4.1/LTC1731-4.2 U TYPICAL APPLICATIO S Linear Charger Using a PNP Transistor 1.5A Single Cell Switching Battery Charger VIN 5V TO 6V VIN = 6V D2 MBRS130LT3 MBRM120T3 R2 1k C1 1nF 7 VCC SENSE 2 DRV CHRG R1 10k RSENSE 0.2 Q2 ZTX749 8 6 TIMER BAT PROG CTIMER 0.1F GND 4 R5 1k 7 VCC 2 IBAT = 500mA 1 5 + Li-ION CELL DRV CHRG 8 C2 22F CER C4 0.47F R3 0.082 1/4W R2 4.7 D1 Q2 Si2305DS MBRS130LT3 6 LTC1731-4.2 3 RPROG 19.6k C5 1F CER SENSE Q1 2N5087 LTC1731-4.2 3 C3 1F C2 10F C1* 0.1F LTC1693-5 TIMER GND PROG 4 1731 TA02 BAT 22H CDRH6D38-220NC 1 + Li-ION 5 R4 18.2k 1% + BATTERY C3 100F 1731 TA03 *AVX 0603ZC104KAT1A RELATED PARTS PART NUMBER DESCRIPTION COMMENTS LT(R)1510-5 500kHz Constant-Voltage/Constant-Current Battery Charger Most Compact, Up to 1.5A, Charges NiCd, NiMH, Li-Ion Cells LT1512 SEPIC Battery Charger VIN Can Be Higher or Lower Than Battery Voltage, 1.5A Switch LT1571-1/LT1571-2 LT1571-5 200kHz/500kHz Constant-Current/Constant-Voltage Battery Charger Family Up to 1.5A Charge Current for 1- or 2-Cell Li-Ion Batteries, Preset and Adjustable Battery Voltages, C/10 Charge Detection LT1620/LT1621 Rail-to-Rail Current Sense Amplifier Precise Output Current Programming, Up to 32V VOUT LTC1730 Integrated Pulse Charger for 1-Cell Li-Ion Battery 0.35 Internal N-FET Requires No Blocking Diode LTC1729 Termination Controller for Li-Ion Time or Charge Current Termination, Automatic Charger/Battery Detection, Status Output, Preconditioning, 8-Lead MSOP LTC1732 Constant-Current/Constant-Voltage Li-Ion Linear Battery Charger Stand Alone Battery, No C or Firmware Required, Auto Recharge of Low Battery, 10-Pin MSOP, Input Supply Detection LTC1734 SOT-23 Li-Ion Battery Charger Needs Only Two External Components, Monitors Charge Current, No Reverse Diode or Sense Resistor Required 12 Linear Technology Corporation 1731f LT/TP 0301 4K * PRINTED IN USA 1630 McCarthy Blvd., Milpitas, CA 95035-7417 (408)432-1900 FAX: (408) 434-0507 www.linear-tech.com LINEAR TECHNOLOGY CORPORATION 1999