LAN9500/LAN9500i LAN9500A/LAN9500Ai USB 2.0 to 10/100 Ethernet Controller PRODUCT FEATURES Data Brief Highlights -- -- -- -- -- Single Chip Hi-Speed USB 2.0 to 10/100 Ethernet Controller Integrated 10/100 Ethernet MAC with Full-Duplex Support Integrated 10/100 Ethernet PHY with HP Auto-MDIX support Integrated USB 2.0 Hi-Speed Device Controller Integrated USB 2.0 Hi-Speed PHY Implements Reduced Power Operating Modes 8kV HBM ESD protection (component level) 8kV contact-discharge, 15kV air discharge ESD protection per IEC61000-4-2 -- -- Target Applications -- -- Embedded Systems Set-Top Boxes PVR's CE Devices Networked Printers USB Port Replicators Standalone USB to Ethernet Dongles Test Instrumentation Industrial -- -- -- -- -- -- Fully compliant with IEEE802.3/802.3u Integrated Ethernet MAC and PHY 10BASE-T and 100BASE-TX support Full- and half-duplex support Full- and half-duplex flow control Preamble generation and removal 1 EEPROM Controller Supports custom operation without EEPROM IEEE 1149.1 (JTAG) Boundary Scan Requires single 25 MHz crystal 1 Software -- -- -- -- -- High-Performance 10/100 Ethernet Controller Various low power modes NetDetach feature increases battery life 1 Supports PCI-like PME wake 1 11 GPIOs Supports bus-powered and self-powered operation Integrated power-on reset circuit Single external 3.3v I/O supply - Internal core regulator Miscellaneous Features -- -- -- -- USB Device Controller -- Fully compliant with Hi-Speed Universal Serial Bus Specification Revision 2.0 -- Supports HS (480 Mbps) and FS (12 Mbps) modes -- Four endpoints supported -- Supports vendor specific commands -- Integrated USB 2.0 PHY -- Remote wakeup supported Power and I/Os -- -- -- -- -- -- -- Key Features Automatic 32-bit CRC generation and checking Automatic payload padding and pad removal Loop-back modes TCP/UDP/IP/ICMP checksum offload support Flexible address filtering modes - One 48-bit perfect address - 64 hash-filtered multicast addresses - Pass all multicast - Promiscuous mode - Inverse filtering - Pass all incoming with status report Wakeup packet support Integrated Ethernet PHY - Auto-negotiation - Automatic polarity detection and correction - HP Auto-MDIX support - Link status change wake-up detection Support for 3 status LEDs External MII and Turbo MII support HomePNATM and HomePlug(R) PHY Windows XP/Vista Driver Linux Driver Win CE Driver MAC OS Driver EEPROM Utility Packaging Environmental -- 56-pin QFN (8x8 mm) Lead-Free RoHS Compliant -- Commercial Temperature Range (0C to +70C) -- Industrial Temperature Range (-40C to +85C) = LAN9500A/LAN9500Ai only SMSC LAN950x Family Revision 1.1 (04-18-13) PRODUCT PREVIEW USB 2.0 to 10/100 Ethernet Controller Order Numbers: LAN9500-ABZJ (Tray) for 56-pin, QFN lead-free RoHS compliant package (0 to +70C temp range) LAN9500-ABZJ-TR (Tape & Reel) for 56-pin, QFN lead-free RoHS compliant package (0 to +70C temp range) LAN9500i-ABZJ (Tray) for 56-pin, QFN lead-free RoHS compliant package (-40 to +85C temp range) LAN9500i-ABZJ-TR (Tape & Reel) for 56-pin, QFN lead-free RoHS compliant package (-40 to +85C temp range) LAN9500A-ABZJ (Tray) for 56-pin, QFN lead-free RoHS compliant package (0 to +70C temp range) LAN9500A-ABZJ-TR (Tape & Reel) for 56-pin, QFN lead-free RoHS compliant package (0 to +70C temp range) LAN9500Ai-ABZJ (Tray) for 56-pin, QFN lead-free RoHS compliant package (-40 to +85C temp range) LAN9500Ai-ABZJ-TR (Tape & Reel) for 56-pin, QFN lead-free RoHS compliant package (-40 to +85C temp range) This product meets the halogen maximum concentration values per IEC61249-2-21 For RoHS compliance and environmental information, please visit www.smsc.com/rohs Copyright (c) 2013 SMSC or its subsidiaries. All rights reserved. Circuit diagrams and other information relating to SMSC products are included as a means of illustrating typical applications. Consequently, complete information sufficient for construction purposes is not necessarily given. Although the information has been checked and is believed to be accurate, no responsibility is assumed for inaccuracies. SMSC reserves the right to make changes to specifications and product descriptions at any time without notice. Contact your local SMSC sales office to obtain the latest specifications before placing your product order. The provision of this information does not convey to the purchaser of the described semiconductor devices any licenses under any patent rights or other intellectual property rights of SMSC or others. All sales are expressly conditional on your agreement to the terms and conditions of the most recently dated version of SMSC's standard Terms of Sale Agreement dated before the date of your order (the "Terms of Sale Agreement"). The product may contain design defects or errors known as anomalies which may cause the product's functions to deviate from published specifications. Anomaly sheets are available upon request. SMSC products are not designed, intended, authorized or warranted for use in any life support or other application where product failure could cause or contribute to personal injury or severe property damage. Any and all such uses without prior written approval of an Officer of SMSC and further testing and/or modification will be fully at the risk of the customer. Copies of this document or other SMSC literature, as well as the Terms of Sale Agreement, may be obtained by visiting SMSC's website at http://www.smsc.com. SMSC is a registered trademark of Standard Microsystems Corporation ("SMSC"). Product names and company names are the trademarks of their respective holders. The Microchip name and logo, and the Microchip logo are registered trademarks of Microchip Technology Incorporated in the U.S.A. and other countries. SMSC DISCLAIMS AND EXCLUDES ANY AND ALL WARRANTIES, INCLUDING WITHOUT LIMITATION ANY AND ALL IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, TITLE, AND AGAINST INFRINGEMENT AND THE LIKE, AND ANY AND ALL WARRANTIES ARISING FROM ANY COURSE OF DEALING OR USAGE OF TRADE. IN NO EVENT SHALL SMSC BE LIABLE FOR ANY DIRECT, INCIDENTAL, INDIRECT, SPECIAL, PUNITIVE, OR CONSEQUENTIAL DAMAGES; OR FOR LOST DATA, PROFITS, SAVINGS OR REVENUES OF ANY KIND; REGARDLESS OF THE FORM OF ACTION, WHETHER BASED ON CONTRACT; TORT; NEGLIGENCE OF SMSC OR OTHERS; STRICT LIABILITY; BREACH OF WARRANTY; OR OTHERWISE; WHETHER OR NOT ANY REMEDY OF BUYER IS HELD TO HAVE FAILED OF ITS ESSENTIAL PURPOSE, AND WHETHER OR NOT SMSC HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Revision 1.1 (04-18-13) 2 PRODUCT PREVIEW SMSC LAN950x Family USB 2.0 to 10/100 Ethernet Controller Overview The LAN950x is a high performance Hi-Speed USB 2.0 to 10/100 Ethernet controller. With applications ranging from embedded systems, set-top boxes, and PVR's, to USB port replicators, USB to Ethernet dongles, and test instrumentation, the device is a high performance and cost competitive USB to Ethernet connectivity solution. The LAN950x contains an integrated 10/100 Ethernet PHY, USB PHY, Hi-Speed USB 2.0 device controller, 10/100 Ethernet MAC, TAP controller, EEPROM controller, and a FIFO controller with a total of 30 KB of internal packet buffering. The internal USB 2.0 device controller and USB PHY are compliant with the USB 2.0 Hi-Speed standard. The device implements Control, Interrupt, Bulk-in, and Bulk-out USB Endpoints. The Ethernet controller supports auto-negotiation, auto-polarity correction, HP Auto-MDIX, and is compliant with the IEEE 802.3 and IEEE 802.3u standards. An external MII interface provides support for an external Fast Ethernet PHY, HomePNA, and HomePlug functionality. Multiple power management features are provided, including various low power modes and "Magic Packet", "Wake On LAN", and "Link Status Change" wake events. These wake events can be programmed to initiate a USB remote wakeup. An internal EEPROM controller exists to load various USB configuration information and the device MAC address. The integrated IEEE 1149.1 compliant TAP controller provides boundary scan via JTAG. USB USB PHY USB 2.0 Device Controller FIFO Controller 10/100 Ethernet MAC Ethernet PHY Ethernet MII: To optional external PHY JTAG TAP Controller SRAM EEPROM Controller EEPROM LAN950x Figure 1 System Diagram SMSC LAN950x Family 3 PRODUCT PREVIEW Revision 1.1 (04-18-13) USB 2.0 to 10/100 Ethernet Controller Package Outline Figure 2 LAN950x 56-QFN Package Table 1 LAN950x 56-QFN Dimensions MIN NOMINAL MAX REMARKS A 0.70 0.85 1.00 Overall Package Height A1 0.00 0.02 0.05 Standoff A2 - - 0.90 Mold Cap Thickness D/E 7.85 8.00 8.15 X/Y Body Size D1/E1 7.55 7.75 7.95 X/Y Mold Cap Size D2/E2 5.80 5.90 6.00 X/Y Exposed Pad Size L 0.30 0.40 0.50 Terminal Length b 0.18 0.25 0.30 Terminal Width K 0.55 - - Center Pad to Pin Clearance e Revision 1.1 (04-18-13) 0.50 BSC Terminal Pitch 4 PRODUCT PREVIEW SMSC LAN950x Family USB 2.0 to 10/100 Ethernet Controller Notes: 1. All dimensions are in millimeters unless otherwise noted. 2. 3. Position tolerance of each terminal and exposed pad is +/- 0.05 mm at maximum material condition. Dimension "b" applies to plated terminals and is measured between 0.15 and 0.30 mm from the terminal tip. The pin 1 identifier may vary, but is always located within the zone indicated. Figure 3 LAN950x 56-QFN Recommended PCB Land Pattern SMSC LAN950x Family 5 PRODUCT PREVIEW Revision 1.1 (04-18-13) Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Microchip: LAN9500A-ABZJ LAN9500-ABZJ-TR LAN9500AI-ABZJ-TR LAN9500I-ABZJ-TR LAN9500I-ABZJ LAN9500A-ABZJTR LAN9500AI-ABZJ LAN9500-ABZJ