Teccor(R) brand Thyristors 1 Amp Standard SCRs Sx01E & SxN1 Series Description Excellent for lower current heat, lamp, and audible alarm controls for home goods. Standard phase control SCRs are triggered with few milliamperes of current at less than 1.5V potential. Features & Benefits t3P)4DPNQMJBOU t(MBTToQBTTJWBUFE junctions t7PMUBHFDBQBCJMJUZVQ to 600 V t4VSHFDBQBCJMJUZVQUP 30 A Applications Main Features Symbol IT(RMS) VDRM /VRRM IGT Value Unit 1 A 400 to 600 V 10 mA Typical applications are AC solid-state switches, fluidlevel sensors, strobes, and capacitive-discharge ignition systems. Schematic Symbol A K G Absolute Maximum Ratings -- Standard SCRs Parameter Test Conditions Value Unit IT(RMS) Symbol RMS on-state current TC = 90C 1 A IT(AV) Average on-state current TC = 90C 0.64 A single half cycle; f = 50Hz; TJ (initial) = 25C 25 single half cycle; f = 60Hz; TJ (initial) = 25C 30 I2t Value for fusing tp = 8.3 ms 3.7 A2s Critical rate of rise of on-state current f = 60Hz ; TJ = 125C 50 A/s Peak gate current TJ = 125C 1.5 A Average gate power dissipation TJ = 125C 0.3 W Storage temperature range -40 to 150 C Operating junction temperature range -40 to 125 C ITSM I 2t di/dt IGM PG(AV) Tstg TJ Sx01E & SxN1 Series Peak non-repetitive surge current 209 A (c)2013 Littelfuse, Inc Specifications are subject to change without notice. Revised: 09/23/13 Teccor(R) brand Thyristors 1 Amp Standard SCRs Electrical Characteristics (TJ = 25C, unless otherwise specified) Symbol IGT Test Conditions Value VD = 12V; RL = 60 VGT dv/dt VD = VDRM; gate open; TJ = 100C MAX. 10 MIN. 1 MAX. 1.5 20 MIN. VD = VDRM; gate open; TJ = 125C VGD VD = VDRM; RL = 3.3 k; TJ = 125C 40 MIN. Unit mA V V/s 0.2 V IH IT = 200mA (initial) MAX. 30 mA tq (1) MAX. 35 s tgt IG = 2 x IGT; PW = 15s; IT = 2A TYP. 2 s (1) IT=1A; tp=50s; dv/dt=20V/s; di/dt=-10A/s Static Characteristics Symbol VTM Test Conditions IT = 2A; tp = 380 s Value Unit 1.6 V MAX. TJ = 25C IDRM / IRRM VDRM = VRRM 10 TJ = 100C 200 MAX. TJ = 125C A 500 Thermal Resistances Symbol Parameter R(J-C) Junction to case (AC) R(J-A) Junction to ambient Value Sx01E 50 SxN1 35* Sx01E 145 Unit C/W C/W Notes : x = voltage * = Mounted on 1 cm2 copper (two-ounce) foil surface Sx01E & SxN1 Series 210 (c)2013 Littelfuse, Inc Specifications are subject to change without notice. Revised: 09/23/13 Teccor(R) brand Thyristors 1 Amp Standard SCRs Figure 1: Normalized DC Gate Trigger Current vs. Junction Temperature Figure 2: Normalized DC Gate Trigger Voltage vs. Junction Temperature 2.0 Ratio of VGT / VGT (TJ = 25C) Ratio of IGT / IGT (TJ = 25C) 2.0 1.5 1.0 0.5 0.0 1.5 1.0 0.5 0.0 -40 -15 10 35 60 85 110 125 -40 -15 10 Figure 3: Normalized DC Holding Current vs. Junction Temperature Instantaneous On-state Current (iT) - Amps Ratio of IH/IH (TJ = 25C) 60 85 110 125 Figure 4: On-State Current vs. On-State Voltage (Typical) 2.0 1.5 1.0 0.5 25 TJ = 25C 20 15 10 5 0 0.0 -40 -15 10 35 60 85 110 0.7 125 0.8 Figure 5: Power Dissipation (Typical) vs. RMS On-State Current Maximum Allowable Case Temperature (TC) - C 0.9 0.8 0.7 0.6 0.5 0.4 0.3 0.2 0.1 0.0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.1 1.2 1.3 1.4 1.5 1.6 130 125 120 115 110 105 100 95 90 CURRENT WAVEFORM: Sinusoidal LOAD: Resistive or Inductive CONDUCTION ANGLE: 180 85 80 0.0 1.0 RMS On-State Current [IT(RMS)] - Amps Sx01E & SxN1 Series 1.0 Figure 6: Maximum Allowable Case Temperature vs. RMS On-State Current 1.0 0.0 0.9 Instantaneous On-state Voltage (vT) - Volts Junction Temperature (TJ) -- (C) Average On-State Power Dissipation [PD(AV)] - (Watts) 35 Junction Temperature (TJ) -- (C) Junction Temperature (TJ) -- (C) 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0 1.1 RMS On-State Current [IT(RMS)] - Amps 211 (c)2013 Littelfuse, Inc Specifications are subject to change without notice. Revised: 09/23/13 Teccor(R) brand Thyristors 1 Amp Standard SCRs Figure 8: Maximum Allowable Ambient Temperature vs. RMS On-State Current 130 Maximum Allowable Ambient Temperature (TA) - C Maximum Allowable Case Temperature (TC) - C Figure 7: Maximum Allowable Case Temperature vs. Average On-State Current 125 120 115 110 105 100 95 90 CURRENT WAVEFORM: Sinusoidal LOAD: Resistive or Inductive CONDUCTION ANGLE: 180 85 80 0.0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 120 CURRENT WAVEFORM: Sinusoidal LOAD: Resistive or Inductive CONDUCTION ANGLE: 180 FREE AIR RATING 100 80 60 40 20 0 0.0 0.8 0.1 0.2 Figure 9: Maximum Allowable Ambient Temperature vs. Average On-State Current 0.4 0.5 0.6 0.7 0.8 0.9 1.0 Figure 10: Peak Capacitor Discharge Current 120 100 CURRENT WAVEFORM: Sinusoidal LOAD: Resistive or Inductive CONDUCTION ANGLE: 180 FREE AIR RATING 100 Peak Discharge Current (ITM) - Amps Maximum Allowable Ambient Temperature (TA) - C 0.3 RMS On-State Current [IT(RMS)] - Amps Average On-State Current [IT(AVE)] - Amps 80 60 40 20 10 ITRM tW 0 0.0 0.1 0.2 0.3 0.4 0.5 0.6 1 0.7 0.5 1.0 10.0 50.0 Pulse Current Duration (tW) - ms Average On-State Current [IT(AVE)] - Amps Figure 11: Peak Capacitor Discharge Current Derating 1.2 Normalized Peak Current 1.0 0.8 0.6 0.4 0.2 0.0 0 25 50 75 100 125 150 Case Temperature (TC) - C Sx01E & SxN1 Series 212 (c)2013 Littelfuse, Inc Specifications are subject to change without notice. Revised: 09/23/13 Teccor(R) brand Thyristors 1 Amp Standard SCRs Figure 12: Surge Peak On-State Current vs. Number of Cycles Peak Surge (Non-repetitive) On-state Current (ITSM) - Amps 100.0 SUPPLY FREQUENCY: 60 Hz Sinusoidal LOAD: Resistive RMS On-State Current: [IT(RMS)]: Maximum Rated Value at Specified Case Temperature Notes: 1. Gate control may be lost during and immediately following surge current interval. 2. Overload may not be repeated until junction temperature has returned to steady-state rated value. 10.0 1.0 0.1 1 10 100 1000 Surge Current Duration -- Full Cycles Soldering Parameters Pre Heat 1Co'SFFBTTFNCMZ - Temperature Min (Ts(min)) 150C - Temperature Max (Ts(max)) 200C - Time (min to max) (ts) oTFDT Average ramp up rate (Liquidus Temp) (TL) to peak 5C/second max TS(max) to TL - Ramp-up Rate 5C/second max Reflow - Temperature (TL) (Liquidus) 217C - Temperature (tL) oTFDPOET Peak Temperature (TP) 260+0/-5 C Time within 5C of actual peak Temperature (tp) oTFDPOET Ramp-down Rate 5C/second max Time 25C to peak Temperature (TP) 8 minutes Max. Do not exceed 280C Sx01E & SxN1 Series tP TP Temperature Reflow Condition Ramp-up TL tL TS(max) Preheat Ramp-do Ramp-down TS(min) tS 25 time to peak temperature 213 Time (c)2013 Littelfuse, Inc Specifications are subject to change without notice. Revised: 09/23/13 Teccor(R) brand Thyristors 1 Amp Standard SCRs Physical Specifications Environmental Specifications Test Terminal Finish 100% Matte Tin-plated Body Material UL recognized epoxy meeting flammability classification 94V-0 Specifications and Conditions AC Blocking Lead Material Temperature Cycling Copper Alloy Temperature/ Humidity Design Considerations High Temp Storage Careful selection of the correct device for the application's operating parameters and environment will go a long way toward extending the operating life of the Thyristor. Good design practice should limit the maximum continuous current through the main terminals to 75% of the device rating. Other ways to ensure long life for a power discrete semiconductor are proper heat sinking and selection of voltage ratings for worst case conditions. Overheating, overvoltage (including dv/dt), and surge currents are the main killers of semiconductors. Correct mounting, soldering, and forming of the leads also help protect against component damage. Low-Temp Storage MIL-STD-750, M-1040, Cond A Applied Peak AC voltage @ 125C for 1008 hours MIL-STD-750, M-1051, 100 cycles; -40C to +150C; 15-min dwell-time EIA / JEDEC, JESD22-A101 1008 hours; 320V - DC: 85C; 85% rel humidity MIL-STD-750, M-1031, 1008 hours; 150C 1008 hours; -40C MIL-STD-750, M-1056 10 cycles; 0C to 100C; 5-min dwelltime at each temperature; 10 sec (max) transfer time between temperature EIA / JEDEC, JESD22-A102 168 hours (121C at 2 ATMs) and 100% R/H Thermal Shock Autoclave Resistance to Solder Heat MIL-STD-750 Method 2031 Solderability ANSI/J-STD-002, category 3, Test A Lead Bend MIL-STD-750, M-2036 Cond E Dimensions - TO-92 (E Package) TC Measuring Point Dimension A B Cathode Anode Gate Inches Millimeters Min Max A 0.176 0.196 B 0.500 D 0.095 E 0.150 Min Max 4.47 4.98 12.70 0.105 2.41 2.67 3.81 F 0.046 0.054 1.16 1.37 G 0.135 0.145 3.43 3.68 H 0.088 0.096 2.23 2.44 J 0.176 0.186 4.47 4.73 K 0.088 0.096 2.23 2.44 L 0.013 0.019 0.33 0.48 M 0.013 0.017 0.33 0.43 All leads insulated from case. Case is electrically nonconductive. E H M G F L D K J Sx01E & SxN1 Series 214 (c)2013 Littelfuse, Inc Specifications are subject to change without notice. Revised: 09/23/13 Teccor(R) brand Thyristors 1 Amp Standard SCRs Dimensions - Compak (C Package) TC / TL Temperature Measurement Point Dimension Gate B D M P A C Cathode Anode F H L E J 0.079 (2.0) K 0.079 (2.0) G 0.079 (2.0) 0.040 (1.0) 0.030 (0.76) 0.110 (2.8) Millimeters Max Min Max 0.130 0.156 3.30 3.95 B 0.201 0.220 5.10 5.60 C 0.077 0.087 1.95 2.20 A N Inches Min D 0.159 0.181 4.05 4.60 E 0.030 0.063 0.75 1.60 F 0.075 0.096 1.90 2.45 G 0.002 0.008 0.05 0.20 H 0.077 0.104 1.95 2.65 J 0.043 0.053 1.09 1.35 K 0.006 0.016 0.15 0.41 L 0.030 0.055 0.76 1.40 M 0.022 0.028 0.56 0.71 N 0.027 0.033 0.69 0.84 P 0.052 0.058 1.32 1.47 Dimensions are in inches (and millimeters). Pad Outline Product Selector Part Number Voltage 400V 600V 800V Gate Sensitivity 1000V Type Package Sx01E X X 10mA Standard SCR TO-92 SxN1 X X 10mA Standard SCR Compak Note: x = Voltage Packing Options Part Number Marking Weight Packing Mode Base Quantity Sx01E Sx01E 0.19 g Bulk 2000 Sx01ERP Sx01E 0.19 g Reel Pack 2000 Sx01EAP Sx01E 0.19 g Ammo Pack 2000 SxN1RP SxN1 0.08 g Embossed Carrier 2500 Note: x = Voltage Sx01E & SxN1 Series 215 (c)2013 Littelfuse, Inc Specifications are subject to change without notice. Revised: 09/23/13 Teccor(R) brand Thyristors 1 Amp Standard SCRs TO-92 (3-lead) Reel Pack (RP) Radial Leaded Specifications Meets all EIA-468-C Standards 1.6 (41.0) 0.236 (6.0) 0.708 (18.0) 0.02 (0.5) 0.098 (2.5) MAX 1.26 (32.0) 0.354 (9.0) 0.5 (12.7) Cathode 0.1 (2.54) 0.2 (5.08) Anode Gate 0.157 DIA (4.0) 14.17(360.0) Flat up 1.97 (50.0) Dimensions are in inches (and millimeters). Direction of Feed TO-92 (3-lead) Ammo Pack (AP) Radial Leaded Specifications Meets all EIA-468-C Standards 0.236 (6.0) 1.62 (41.2) 0.708 (18.0) 0.02 (0.5) 0.098 (2.5) MAX 1.27 (32.2) 0.354 (9.0) Anode 0.1 (2.54) 0.5 (12.7) 0.2 (5.08) 0.157 (4.0) DIA Cathode Gate Flat down n of Directio Feed 25 Devices per fold 1.85 (47.0) 12.2 (310.0) 1.85 (47.0) Dimensions are in inches (and millimeters). 13.3 (338.0) Sx01E & SxN1 Series 216 (c)2013 Littelfuse, Inc Specifications are subject to change without notice. Revised: 09/23/13 Teccor(R) brand Thyristors 1 Amp Standard SCRs Compak Embossed Carrier Reel Pack (RP) Specifications Meets all EIA-481-1 Standards 0.157 (4.0) 0.47 (12.0) Anode 0.36 (9.2) 8.0 0.315 (8.0) Gate 0.059 DIA (1.5) Cathode Cover tape 12.99 (330.0) 0.512 (13.0) Arbor Hole Dia. Dimensions are in inches (and millimeters). 0.49 (12.4) Direction of Feed Part Numbering System S 6 01 E DEVICE TYPE S: SCR Part Marking System 75 TO-92 (E Package) S601E CURRENT RATING 01: 1A (TO-92) N: 1A (Compak) Sx01E & SxN1 Series S6N1 Lead Form Dimensions xx: Lead Form Option (R) VOLTAGE RATING 4: 400V 6: 600V Compak (C Package) SENSITIVITY & TYPE [blank]: 10 mA (TO-92) 1: 10 mA (Compak) YMLXX (R) YMXXX Date Code Marking Date Code Marking Y:Year Code M: Month Code L: Location Code XX: Lot Serial Code PACKAGE TYPE E: TO-92 SCR N: Compak 217 Y:Year Code M: Month Code XXX: Lot Trace Code (c)2013 Littelfuse, Inc Specifications are subject to change without notice. Revised: 09/23/13