DP83256 - National Semiconductor

TL/F/11708

DP83256/56-AP/57 PLAYERaDevice (FDDI Physical Layer Controller)

PRELIMINARY

October 1994

DP83256/56-AP/57

PLAYERaTM Device (FDDI Physical Layer Controller)

General Description

The DP83256/56-AP/57 Enhanced Physical Layer Control-

ler (PLAYERadevice) implements one complete Physical

Layer (PHY) entity as defined by the Fiber Distributed Data

Interface (FDDI) ANSI X3T9.5 standard.

The PLAYERadevice integrates state of the art digital

clock recovery and improved clock generation functions to

enhance performance, eliminate external components and

remove critical layout requirements.

FDDI Station Management (SMT) is aided by Link Error

Monitoring support, Noise Event Timer (TNE) support, Op-

tional Auto Scrubbing support, an integrated configuration

switch and built-in functionality designed to remove all strin-

gent response time requirements such as PCÐReact and

CFÐReact.

Features

YSingle chip FDDI Physical Layer (PHY) solution

YIntegrated Digital Clock Recovery Module provides en-

hanced tracking and greater lock acquisition range

YIntegrated Clock Generation Module provides all neces-

sary clock signals for an FDDI system from an external

12.5 MHz reference

YAlternate PMD Interface (DP83256-AP/57) supports

UTP twisted pair FDDI PMDs with no external clock re-

covery or clock generation functions required

YNo External Filter Components

YConnection Management (CMT) Support (LEM, TNE,

PCÐReact, CFÐReact, Auto Scrubbing)

YFull on-chip configuration switch

YLow Power CMOS-BIPOLAR design using a single 5V

supply

YFull duplex operation with through parity

YSeparate management interface (Control Bus)

YSelectable Parity on PHY-MAC Interface and Control

Bus Interface

YTwo levels of on-chip loopback

Y4B/5B encoder/decoder

YFraming logic

YElasticity Buffer, Repeat Filter, and Smoother

YLine state detector/generator

YSupports single attach stations, dual attach stations

and concentrators with no external logic

YDP83256 for SAS/DAS single path stations

YDP83257 for SAS/DAS single/dual path stations

YDP83256-AP for SAS/DAS single path stations that re-

quire the alternate PMD interface

TL/F/11708– 1

FIGURE 1-1. FDDI Chip Set Overview

TRI-STATEÉis a registered trademark of National Semiconductor Corporation.

BMACTM, BSITM, CDDTM, CDLTM , CRDTM, CYCLONETM, MACSITM, PLAYERTM , PLAYERaTM and TWISTERTM are trademarks of National Semiconductor Corporation.

C1995 National Semiconductor Corporation RRD-B30M115/Printed in U. S. A.

Table of Contents

1.0 FDDI CHIP SET OVERVIEW

1.1 FDDI 2-Chip Set

1.2 FDDI TP-PMD Solutions

2.0 ARCHITECTURE DESCRIPTION

2.1 Block Overview

2.2 Interfaces

3.0 FUNCTIONAL DESCRIPTION

3.1 Clock Recovery Module

3.2 Receiver Block

3.3 Transmitter Block

3.4 Configuration Switch

3.5 Clock Generation Module

3.6 Station Management Support

3.7 PHY-MAC Interface

3.8 PMD Interface

4.0 MODES OF OPERATION

4.1 Run Mode

4.2 Stop Mode

4.3 Loopback Mode

4.4 Device Reset

4.5 Cascade Mode

5.0 REGISTERS

5.1 Mode Register (MR)

5.2 Configuration Register (CR)

5.3 Interrupt Condition Register (ICR)

5.4 Interrupt Condition Mask Register (ICMR)

5.5 Current Transmit State Register (CTSR)

5.6 Injection Threshold Register (IJTR)

5.7 Injection Symbol Register A (ISRA)

5.8 Injection Symbol Register B (ISRB)

5.9 Current Receive State Register (CRSR)

5.10 Receive Condition Register A (RCRA)

5.11 Receive Condition Register B (RCRB)

5.12 Receive Condition Mask Register A (RCMRA)

5.13 Receive Condition Mask Register B (RCMRB)

5.14 Noise Threshold Register (NTR)

5.15 Noise Prescale Threshold Register (NPTR)

5.16 Current Noise Count Register (CNCR)

5.17 Current Noise Prescale Count Register (CNPCR)

5.18 State Threshold Register (STR)

5.19 State Prescale Threshold Register (SPTR)

5.20 Current State Count Register (CSCR)

5.21 Current State Prescale Count Register (CSPCR)

5.22 Link Error Threshold Register (LETR)

5.23 Current Link Error Count Register (CLECR)

5.24 User Definable Register (UDR)

5.25 Device ID Register (DIR)

5.26 Current Injection Count Register (CIJCR)

5.27 Interrupt Condition Comparison Register (ICCR)

5.28 Current Transmit State Comparison Register

(CTSCR)

5.29 Receive Condition Comparison Register A (RCCRA)

5.30 Receive Condition Comparision Register B (RCCRB)

5.31 Mode Register 2 (MODE2)

5.32 CMT Condition Comparison Register (CMTCCR)

5.33 CMT Condition Register (CMTCR)

5.34 CMT Condition Mask Register (CMTCMR)

5.35 Reserved Registers 22H-23H (RR22H-RR23H)

5.36 Scrub Timer Threshold Register (STTR)

5.37 Scrub Timer Value Register (STVR)

5.38 Trigger Definition Register (TDR)

5.39 Trigger Transition Configuration Register (TTCR)

5.40 Reserved Registers 28H-3AH (RR28H-RR3AH)

5.41 Clock Generation Module Register (CGMREG)

5.42 Alternate PMD Register (APMDREG)

5.43 Gain Register (GAINREG)

5.44 Reserved Registers 3EH-3FH (RR3EH-RR3FH)

6.0 SIGNAL DESCRIPTIONS

6.1 DP83256VF Signal Descriptions

6.2 DP83256VF-AP Signal Descriptions

6.3 DP83257VF Signal Descriptions

7.0 ELECTRICAL CHARACTERISTICS

7.1 Absolute Maximum Ratings

7.2 Recommended Operating Conditions

7.3 DC Electrical Characteristics

7.4 AC Electrical Characteristics

8.0 CONNECTION DIAGRAMS

8.1 DP83256VF Connection Diagram/Pin Descriptions

8.2 DP83256VF-AP Connection Diagram/Pin Descrip-

tions

8.3 DP83257VF Connection Diagram/Pin Descriptions

9.0 PACKAGE INFORMATION

9.1 Land Patterns

9.2 Mechanical Drawings

1.0 FDDI Chip Set Overview

National Semiconductor’s next generation FDDI 2-chip set

consists of two components as shown in

Figure 1-1

. The

PLAYERadevice integrates the features of the DP83231

CRDTM Clock Recovery Device, DP83241 CDDTM Clock

Distribution Device, and DP83251/55 PLAYERTM Physical

Layer Controller. In addition, the PLAYERadevice contains

enhanced SMT support.

National Semiconductor’s FDDI TP-PMD Solutions consist

of two componentsÐthe DP83222 CYCLONETM Twisted

Pair FDDI Stream Cipher Device and the DP83223A

TWISTERTM Twisted Pair FDDI Transceiver Device.

For more information on the other devices of the chip set,

consult the appropriate datasheets and application notes.

1.1 FDDI 2-CHIP SET

DP83256/56-AP/57 PLAYERa

Device Physical Layer Controller

The PLAYERadevice implements the Physical Layer

(PHY) protocol as defined by the ANSI FDDI PHY X3T9.5

standard.

Features

YSingle chip FDDI Physical Layer (PHY) solution

YIntegrated Digital Clock Recovery Module provides en-

hanced tracking and greater lock acquisition range

YIntegrated Clock Generation Module provides all neces-

sary clock signals for an FDDI system from an external

12.5 MHz reference

YAlternate PMD Interface (DP83256-AP/57) supports

UTP twisted pair FDDI PMDs with no external clock re-

covery or clock generation functions required

YNo External Filter Components

YConnection Management (CMT) Support (LEM, TNE,

PCÐReact, CFÐReact, Auto Scrubbing)

YFull on-chip configuration switch

YLow Power CMOS-BIPOLAR design using a single 5V

supply

YFull duplex operation with through parity

YSeparate management interface (Control Bus)

YSelectable Parity on PHY-MAC Interface and Control

Bus Interface

YTwo levels of on-chip loopback

Y4B/5B encoder/decoder

YFraming logic

YElasticity Buffer, Repeat Filter, and Smoother

YLine state detector/generator

YSupports single attach stations, dual attach stations

and concentrators with no external logic

YDP83256/56-AP for SAS/DAS single path stations

YP83257 for SAS/DAS single/dual path stations

In addition, the DP83257 contains the additional PHYÐDa-

ta.request and PHYÐData.indicate ports required for con-

centrators and dual attach, dual path stations.

DP83266 MACSITM Device Media

Access Controller and System

Interface

The DP83266 Media Access Controller and System Inter-

face (MACSI) implements the ANSI X3T9.5 Standard Media

Access Control (MAC) protocol for operation in an FDDI

token ring and provides a comprehensive System Interface.

The MACSI device transmits, receives, repeats, and strips

tokens and frames. It produces and consumes optimized

data structures for efficient data transfer. Full duplex archi-

tecture with through parity allows diagnostic transmission

and self testing for error isolation in point-to-point connec-

tions.

The MACSI device includes the functionality of both the

DP83261 BMAC device and the DP83265 BSI-2 device with

additional enhancements for higher performance and reli-

ability.

Features

YOver 9 Kbytes of on-chip FIFO

Y5 DMA Channels (2 Output and 3 Input)

Y12.5 MHz to 33 MHz operation

YFull duplex operation with through parity

YReal-time VOID frame stripping indicator for bridges

YOn-chip Address bit swapping capability

Y32-bit wide Address/Data path with byte parity

YProgrammable transfer burst sizes of 4 or 8 32-bit

words

YReceive frame filtering services

YFrame-per-Page mode controllable on each DMA

channel

YDemultiplexed Addresses supported on ABus

YNew multicast address matching

YANSI X3T9.5 MAC standard defined ring service op-

tions

YSupports all FDDI Ring Scheduling Classes (Synchro-

nous, Asynchronous, etc.)

YSupports Individual, Group, Short, Long, and External

Addressing.

YGenerates Beacon, Claim, and Void frames

YExtensive ring and station statistics gathering

YExtension for MAC level bridging

YEnhanced SBus compatibility

YInterfaces to DRAMs or directly to system bus

YSupports frame Header/Info splitting

YProgrammable Big or Little Endian alignment

DP83222 CYCLONE Twisted Pair

FDDI Stream Cipher Device

General Description

The DP83222 CYCLONE Stream Cipher Scrambler/Des-

crambler Device is an integrated circuit designed to inter-

face directly with the serial bit streams of a Twisted Pair

FDDI PMD. The DP83222 is designed to be fully compatible

with the National Semiconductor FDDI Chip Sets, including

twisted pair FDDI Transceivers, such as the DP83223A

Twisted Pair Transceiver (TWISTER). The DP83222 re-

quires a 125 MHz Transmit Clock and corresponding Re-

ceive Clock for synchronous data scrambling and descram-

bling. The DP83222 is compliant with the ANSI X3T9.5

TP-PMD standard and is required for the reduction of EMI

emission over unshielded media. The DP83222 is specified

to work in conjunction with existing twisted pair transceiver

signalling schemes and enables high bandwidth transmis-

sion over Twisted Pair copper media.

Features

YEnables 100 Mbps FDDI signalling over Category 5

Unshielded Twisted Pair (UTP) cable and Type 1

Shielded Twisted Pair (STP)

YReduces EMI emissions over Twisted Pair media

YCompatible with ANSI X3T9.5 TP-PMD standard

YRequires a single a5V supply

YTransparent mode of operation

YFlexible NRZ and NRZI format options

YAdvanced BiCMOS process

YSignal Detect and Clock Detect inputs provided for en-

hanced functionality

YSuitable for Fiber Optic PMD replacement applications

DP83223A TWISTER High Speed

Networking Transceiver Device

General Description

The DP83223A Twisted Pair Transceiver is an integrated

circuit capable of driving and receiving either binary or

(MLT-3) encoded datastreams. The DP83223A Transceiver

is designed to interface directly with standards compliant

FDDI, 100BASE-TX or STS-3c ATM chip sets, allowing low

cost data links over copper based media. The DP83223A

allows links of up to 100 meters over both Shielded Twisted

Pair (STP) and datagrade Unshielded Twisted Pair (UTP) or

equivalent. The electrical performance of the DP83223A

meets or exceeds all performance parameters specified

in the ANSI X3T9.5 TP-PMD standard, the IEEE 802.3

100BASE-TX Fast Ethernet Specification and the ATM Fo-

rum 155 Mbps Twisted Pair PMD Interface Specification.

The DP83223A also provides important features such as

baseline restoration, TRI-STATEÉcapable transmit outputs,

and controlled transmit output edge rates (to reduce EMI

radiation) for both binary and MLT-3 modes of operation.

Features

YCompliant with ANSI X3T9.5 TP-PMD standard

YCompliant with IEEE 802.3 100BASE-TX Ethernet draft

standard

YCompliant with ATM Forum 155 Mbps Twisted Pair

Specification

YIntegrated baseline restoration circuit

YIntegrated transmitter and receiver with adaptive equali-

zation circuit

YProgrammable binary or MLT-3 operation

YIsolated TX and RX power supplies for minimum noise

coupling

YControlled transmit output edge rates for reduced EMI

YTRI-STATE capable current transmit outputs

YLoopback feature for board diagnostics

YProgrammable transmit voltage amplitude

2.0 Architecture Description

2.1 BLOCK OVERVIEW

The PLAYERadevice is comprised of six blocks: Clock

Recovery, Receiver, Configuration Switch, Transmitter, Sta-

tion Management (SMT) Support, and Clock Generation

Module as shown in

Figure 2-1

Clock Recovery

The Clock Recovery Module accepts a 125 Mbps NRZI data

stream from the external PMD receiver. It then provides the

extracted and synchronized data and clock to the Receiver

block.

The Clock Recovery Module performs the following opera-

tions:

#Locks to and tracks the incoming NRZI data stream

#Extracts data stream and synchronized 125 MHz clock

Receiver

During normal operation, the Receiver Block accepts serial

data as inputs at the rate of 125 Mbps from the Clock Re-

covery Module. During the Internal Loopback mode of oper-

ation, the Receiver Block accepts data directly from the

Transmitter Block.

The Receiver Block performs the following operations:

#Optionally converts the incoming data stream from NRZI

to NRZ.

#Decodes the data from 5B to 4B coding.

#Converts the serial bit stream into 10-bit bytes composed

of 8 bits data, 1 bit parity, and 1 bit control information.

#Compensates for the differences between the upstream

station clock and the local clocks.

#Decodes Line States.

#Detects link errors.

#Presents data symbol pairs (bytes) to the Configuration

Switch Block.

Configuration Switch

An FDDI station may be in one of three configurations: Iso-

late, Wrap or Thru. The Configuration Switch supports these

configurations by switching the transmitted and received

data paths between PLAYERadevices and one or more

MACSI devices.

The configuration switch is integrated into the PLAYERa

device, therefore no external logic is required for this func-

tion.

Setting the Configuration switch can be done explicitly via

the Control Bus Interface or it can be set automatically with

the CFÐReact SMT Support feature.

TL/F/11708– 2

FIGURE 2-1. PLAYERaDevice Block Diagram

2.0 Architecture Description (Continued)

Transmitter

The Transmitter Block accepts 10-bit bytes composed of 8

bits data, 1 bit parity, and 1 bit control information from the

Configuration Switch.

The Transmitter Block performs the following operations:

#Encodes the data from 4B to 5B coding.

#Filters out code violations from the data stream.

#Generates Idle, Master, Halt, Quiet, or other user defined

symbol pairs upon request.

#Converts the data stream from NRZ to NRZI format for

transmission.

#Provides smoothing function when necessary.

During normal operation, the Transmitter Block presents se-

rial data to the PMD transmitter. While in Internal Loopback

mode, the Transmitter Block presents serial data to the Re-

ceiver Block. While in the External Loopback mode, the

Transmitter Block presents serial data to the Clock Recov-

ery Module.

Clock Generation Module

The Clock Generation Module is an integrated phase locked

loop that generates all of the required clock signals for the

PLAYERadevice and an FDDI system from a single

12.5 MHz reference.

The Clock Generation Module features:

#High precision clock timing generated from a single

12.5 MHz reference.

#Multiple precision phased (8 ns/16 ns) 12.5 MHz Local

Byte Clocks to eliminate timing skew in large multi-board

concentrator configurations.

#LBC timing which is insensitive to loading variations over

a wide range (20 pF to 70 pF) of LBC loads.

#A selectable dual frequency system clock.

#Low clock edge jitter, due to high VCO stability.

Station Management (SMT) Support

The Station Management Support Block provides a number

of useful features to simplify the implementation of the Con-

nection Management (CMT) portion of SMT.

These features eliminate the time critical CMT response

time constraints imposed by PCÐReact and CFÐReact

times.

Integrated counters and timers eliminate the need for addi-

tional external devices.

The following are the CMT features supported:

#PCÐReact

#CFÐReact

#Auto Scrubbing (TCF Timer)

#Timer, Idle Detection (TID Timer)

#Noise Event Counter (TNE Timer)

#Link Error Monitor (LEM Counter)

2.2 INTERFACES

The PLAYERadevice connects to other devices via five

functional interfaces: PMD Interface, PHY Port Interface,

Control Bus Interface, Clock Interface, and the Miscellane-

ous Interface.

PMD Interface

The PMD Interface connects the PLAYERadevice to a

standard FDDI Physical Media Connection such as a fiber

optic transceiver or a copper twisted pair transceiver. It is a

125 MHz full duplex serial connection.

The DP83256-AP and DP83257 PLAYERadevices contain

two PMD interfaces. The Primary PMD Interface should be

used for all PMD implementations that do not require an

external scrambler/descrambler function, clock recovery

function, or clock generation function, such as a Fiber Optic

or Shielded Twisted Pair (SDDI) PMD. The second, Alter-

nate PMD Interface can be used to support Unshielded

Twisted Pair (UTP) PMDs that require external scrambling,

and allows implementation with no external clock recovery

or clock generation functions required.

PHY Port Interface

The PHY Port Interface connects the PLAYERadevice to

one or more MAC devices and/or PLAYERadevices. Each

PHY Port Interface consists of two byte-wide interfaces, one

for PHY Request data input to the PLAYERadevice and

one for the PHY Indicate data output of the PLAYERade-

vice. Each byte-wide interface consists of a parity bit (odd

parity), a control bit, and two 4-bit symbols.

The DP83257 PLAYERadevice has two PHY Port Interfac-

es while the DP83256 has one PHY Port Interface.

Control Bus Interface

The Control Bus Interface connects the PLAYERadevice

to a wide variety of microprocessors and microcontrollers.

The Control Bus is an asynchronous interface which pro-

vides access to 64 8-bit registers which monitor and control

the behavior of the PLAYERadevice.

The Control Bus Interface allows a user to:

#Configure SMT features.

#Program the Configuration Switch.

#Enable/disable functions within the Transmitter and Re-

ceiver Blocks (i.e., NRZ/NRZI Encoder, Smoother, PHY

Request Data Parity, Line State Generation, Symbol pair

Injection, NRZ/NRZI Decoder, Cascade Mode, etc.).

The Control Bus Interface also can be used to perform the

following functions:

#Monitor Line States received.

#Monitor link errors detected by the Receiver Block.

#Monitor other error conditions.

Clock Interface

The Clock Interface is used to configure the Clock Genera-

tion Module and to provide the required clock signals for an

FDDI system.

The following clock signals are generated:

#5 phase offset 12.5 MHz Local Byte Clocks

#25 MHz Local Symbol Clock

#15.625 or 31.25 MHz System Clock

Miscellaneous Interface

The Miscellaneous Interface consists of:

#A reset signal.

#User definable sense signals.

#User definable enable signals.

#Synchronization for cascading PLAYERadevices (a

high-performance non-FDDI mode).

#Device Power and Ground pins.

3.0 Functional Description

The PLAYERadevice is comprised of six blocks: Clock

Recovery, Receiver, Transmitter, Configuration Switch,

Clock Generation, and Station Management Support.

3.1 CLOCK RECOVERY MODULE

The Clock Recovery Module accepts a 125 Mbps NRZI data

stream from the external PMD receiver. It then provides the

extracted and synchronized data and clock to the Receiver

block.

The Clock Recovery Module performs the following opera-

tions:

#Locks onto and tracks the incoming NRZI data stream

#Extracts the data stream and the synchronized 125 MHz

clock

The Clock Recovery Module is implemented using an ad-

vanced digital architecture that replaces sensitive analog

blocks with digital circuitry. This allows the PLAYERade-

vice to be manufactured to tighter tolerances since it is less

sensitive to processing variations that can adversely affect

analog circuits.

The Clock Recovery Module is comprised of 5 main func-

tional blocks:

Digital Phase Detector

Digital Phase Error Processor

Digital Loop Filter

Digital Phase to Frequency Converter

Frequency Controlled Oscillator

See

Figure 3-1

, Clock Recovery Module Block Diagram.

DIGITAL PHASE DETECTOR

The Digital Phase Detector has two main functions: phase

error detection and data recovery.

Phase error detection is accomplished by a digital circuit

that compares the input data (PMID) to an internal phase-

locked 125 MHz reference clock and generates a pair of

error signals. The first signal is a pulse whose width is equal

to the phase error between the input data and a reference

clock and the second signal isa4nsreference pulse.

These signals are fed into the Digital Phase Error Processor

block.

The data recovery function converts the incoming encoded

data stream (PMID) into synchronized data and clock sig-

nals. When the circuit is in lock the rising edge of the recov-

ered clock is exactly centered in the recovered data bit cell.

The digital phase detector uses a common path for phase

error detection and data recovery so as to minimize clock

Static Alignment Error (SAE). Phase error averaging is also

included so that phase errors generated by positive and

negative PMID edges equally affect the clock recovery cir-

cuit. This greatly improves the immunity to Duty Cycle Dis-

tortion (DCD) in the data recovery circuit.

DIGITAL PHASE ERROR PROCESSOR

The Digital Phase Error Processor is responsible for sam-

pling the Phase Detector’s phase error outputs and produc-

ing two digital outputs that indicate to the digital loop filter

how to adjust for a difference between the data phase and

reference phases.

The Phase Error Processor is designed to eliminate the ef-

fects of different clock edge densities between data sym-

bols and the various line state symbols on the PLL’s loop

gain.

TL/F/11708– 3

FIGURE 3-1. Clock Recovery Module Block Diagram

3.0 Functional Description (Continued)

Since the loop gain is held constant regardless of the in-

coming signal edge density, PLL characteristics such as jit-

ter, acquisition rate, locking range etc., are deterministic and

show minimal spread under various operating environments.

The phase error processor also automatically puts the loop

in open-loop-mode when the incoming data stream contains

abnormal low edge rates. When the PLL is in open-loop-

mode, no update is made to the PLL’s filter variables in the

filter block. The PLL can then use the pretrained frequency

and phase contents to perform data recovery. Since the

loop is implemented digitally, these values (the frequency

and phase variables) are retained. The resolution of the fre-

quency variable is about 1.3 ppm of the incoming frequency.

The resolution of the phase variable is about 40 ps.

DIGITAL LOOP FILTER

The digital loop filter emulates a 1-pole, 1-zero filter and

uses an automatic acquisition speed control circuit to dy-

namically adjust loop parameters.

The digital loop filter takes the phase error indicator signals

Data Valid and Up/Down from the Phase Error processor

and accumulates errors over a few cycles before passing on

the Data Valid and Up/Down signals to the Phase Error to

Frequency converter.

The filter has 4 sets of bandwidth and damping parameters

which are switched dynamically by an acquisition control

circuit. The input Signal Detect (SD) starts the sequence

and, thereafter, no user programming is required to finish

the sequence.

At the completion of the locking sequence, the loop has the

narrowest bandwidth such that the loop produces minimal

recovered clock jitter. The PLL can track an incoming fre-

quency offset of approximately g200 ppm. After the acqui-

sition sequence, the equivalent natural frequency of the

loop is reduced to about 7 kHz (g56 ppm) of frequency

offset.

The automatic tracking mechanism allows the loop to quick-

ly lock onto the initial data stream for data recovery (typical-

ly less than 10 ms) and yet produce very little recovered

clock jitter.

PHASE ERROR TO FREQUENCY CONVERTER (O–F)

The Phase Error to Frequency Converter takes the Data

Valid and Up/Down signals modified by the Digital Loop

Filter and converts them to triangle waves. The frequency of

the triangle waves is then used to control the Frequency

Controlled Oscillator’s (FCO) 250 MHz oscillations.

Each valid Up or Down signal causes a partial 7-bit counter

(using only 96 counts) to increment or decrement at the

O–F converter’s clock rate of 15.625 MHz (250 MHz/16).

When the Data Valid signal is not asserted, the counter

holds count.

The counter value is used to produce 3 triangle waves that

are offset in phase by 120 degrees. This is done with a

special Pulse Density Modulator waveform synthesizer

which takes the place of a traditional Digital-Analog convert-

er. The frequency of the triangle waves tells the Frequency

Controlled Oscillator how much to adjust oscillation. The

phase relationships (leading or lagging) between the 3 sig-

nals indicates the direction of change.

The minimum frequency of the triangle waves is 0 and cor-

responds to the case when the PLL is in perfect lock with

the incoming signal.

The maximum frequency that the O–F converter can pro-

duce determines the locking range of the PLL. In this case

the maximum frequency of each triangle wave is 162.76

kHz, which is produced when the O–F converter gets a

continuous count in one direction that is valid every O–F

converter clock cycle of 15.625 MHz (250 MHz/16). The

triangle waves have an amplitude resolution of 48 digital

steps, so a full rising and falling period takes 96 counts

which produces a maximum frequency of 162.76 kHz

(1/(1/15.625 kHz *96)).

The 96 digital counts of the triangle waves also lead to a

very fine PLL phase resolution of 42 ps (4 ns/96 counts).

This high phase resolution is achieved using very low fre-

quency signals, in contrast to a standard PLL which must

operate at significantly higher frequencies than the data be-

ing tracked to achieve such high phase resolution.

FREQUENCY CONTROLLED OSCILLATOR (FCO)

The frequency controlled oscillator produces a 250 MHz

clock that, when divided by 2, is phase locked to the incom-

ing data’s clock.

The FCO uses three 250 MHz reference clock signals from

the Clock Generation Module and three 0 Hz to 162.76 kHz

error clock signals from the Phase Error to Frequency Con-

verter as inputs. Each signal in a triplet is 120 degrees

phase shifted from the next.

Each corresponding pair (one 250 MHz and one error sig-

nal) of signals is mixed together using an amplitude switch-

ing modulator, with the error signal modulating the refer-

ence. All of the outputs are then summed together to pro-

duce the final 250 MHz afmphase locked clock signal,

where fmis the error frequency.

3.0 Functional Description (Continued)

3.2 RECEIVER BLOCK

During normal operation, the Receiver Block accepts serial

data input at the rate of 125 Mbps from the Clock Recovery

Module. During the Internal Loopback mode of operation,

the Receiver Block accepts input data from the Transmitter

Block.

The Receiver Block performs the following operations:

#Optionally converts the incoming data stream from NRZI

to NRZ.

#Decodes the data from 5B to 4B coding.

#Converts the serial bit stream into the National byte-wide

code.

#Compensates for the differences between the upstream

station clock and the local clock.

#Decodes Line States.

#Detects link errors.

#Presents data symbol pairs to the Configuration Switch

Block.

The Receiver Block consists of the following functional

blocks:

NRZI to NRZ Decoder

Shift Register

Framing Logic

Symbol Decoder

Line State Detector

Elasticity Buffer

Link Error Detector

See

Figure 3-2.

NRZI TO NRZ DECODER

The NRZI to NRZ Decoder converts Non-Return-To-Zero-

Invert-On-Ones data to Non-Return-To-Zero format.

NRZ format data is the natural data format that the receiver

block utilizes internally, so this function is required when the

standard NRZI format data is fed into the device. The re-

ceiver block can bypass this conversion function in the case

where an alternate data source outputs NRZ format data.

This function can be enabled and disabled through bit 7

(RNRZ) of the Mode Register (MR). When the bit is cleared,

it converts the incoming bit stream from NRZI to NRZ. This

is the normal configuration required. When the bit is set, the

incoming NRZ bit stream is passed unchanged.

SHIFT REGISTER

The Shift Register converts the serial bit stream into sym-

bol-wide data for the 5B/4B Decoder.

The Shift Register also provides byte-wide data for the

Framing Logic.

FRAMING LOGIC

The Framing Logic performs the Framing function by detect-

ing the beginning of a frame or the Halt-Halt or Halt-Quiet

symbol pair.

The J-K symbol pair (11000 10001) indicates the beginning

of a frame during normal operation. The Halt-Halt (00100

00100) and Halt-Quiet (00100 00000) symbol pairs are de-

tected for Connection Management (CMT).

TL/F/11708– 4

FIGURE 3-2. Receiver Block Diagram

3.0 Functional Description (Continued)

Framing may be temporarily suspended (i.e. framing hold),

in order to maintain data integrity.

Detecting JK

The JK symbol pair can be used to detect the beginning of a

frame during Active Line State (ALS) and Idle Line State

(ILS) conditions.

While the Line State Detector indicates Idle Line State the

receiver ‘‘reframes’’ upon detecting a JK symbol pair and

enters the Active Line State.

During Active Line State, acceptance of a JK symbol (re-

framing) is allowed for any on-boundary JK which is detect-

ed at least 1.5 byte times after the previous JK.

During Active Line State, once reframed on a JK, a subse-

quent off-boundary JK is ignored, even if it is detected be-

yond 1.5 byte times after the previous JK.

During Active Line State, an Idle or Ending Delimiter (T)

symbol will allow reframing on any subsequent JK, if a JK is

detected at least 1.5 byte times after the previous JK.

Detecting HALT-HALT AND HALT-QUIET

During Idle Line State, the detection of a Halt-Halt, or Halt-

Quiet symbol pair will still allow the reframing of any subse-

quent on-boundary JK.

Once a JK is detected during Active Line State, off-bounda-

ry Halt-Halt, or Halt-Quiet symbol pairs are ignored until the

Elasticity Buffer (EB) has an opportunity to recenter. They

are treated as violations.

After recentering on a Halt-Halt, or Halt-Quiet symbol pair,

all off boundary Halt-Halt or Halt-Quiet symbol pairs are ig-

nored until the EB has a chance to recenter during a line

state other than Active Line State (which may be as long as

2.8 byte times).

SYMBOL DECODER

The Symbol Decoder is a two level system. The first level is

a 5-bit to 4-bit converter, and the second level is a 4-bit

symbol pair to byte-wide code converter.

The first level latches the received 5-bit symbols and de-

codes them into 4-bit symbols. Symbols are decoded into

two types: data and control. The 4-bit symbols are sent to

the Line State Detector and the second level of the Symbol

Decoder. See Table 3-1 for the 5B/4B Symbol Decoding

list.

The second level translates two symbols from the 5B/4B

converter and the line state information from the Line State

Detector into the National byte-wide code.

LINE STATE DETECTOR

The ANSI X3T9.5 FDDI Physical Layer (PHY) standard

specifies eight Line States that the Physical Layer can

transmit. These Line States are used in the Connection

Management process. They are also used to indicate data

within a frame during normal operation.

The Line States are reported through the Current Receive

State Register (CRSR), Receive Condition Register A

(RCRA), and Receive Condition Register B (RCRB).

TABLE 3-1. 5B/4B Symbol Decoding

Symbol Incoming 5B Decoded 4B

0 11110 0000

1 01001 0001

2 10100 0010

3 10101 0011

4 01010 0100

5 01011 0101

6 01110 0110

7 01111 0111

8 10010 1000

9 10011 1001

A 10110 1010

B 10111 1011

C 11010 1100

D 11011 1101

E 11100 1110

F 11101 1111

I (Idle) 11111 1010

H (Halt) 00100 0001

JK (Starting 11000 and 1101

Delimiter) 10001

T (Ending 01101 0101

Delimiter)

R (Reset) 00111 0110

S (Set) 11001 0111

Q (Quiet) 00000 0010

V (Violation) 00001 0010

V 00010 0010

V 00011 0010

V 00101 0010

V 00110 0010

V 01000 0010

V 01100 0010

V 10000 0010

Note: VÊdenotes PHY Invalid or an Elasticity Buffer stuff byte

IÊdenotes Idle symbol in ILS or an Elasticity Buffer stuff byte

LINE STATES DESCRIPTION

Active Line State

The Line State Detector recognizes the incoming data to be

in the Active Line State upon the reception of the Starting

Delimiter (JK symbol pair).

The Line State Detector continues to indicate Active Line

State while receiving data symbols, Ending Delimiter (T

symbols), and Frame Status symbols (R and S) after the JK

symbol pair.

Idle Line State

The Line State Detector recognizes the incoming data to be

in the Idle Line State upon the reception of 2 Idle symbol

pairs nominally (plus up to 9 bits of 1 in start up cases).

Idle Line State indicates the preamble of a frame or the lack

of frame transmission during normal operation. Idle Line

State is also used in the handshake sequence of the PHY

Connection Management process.

3.0 Functional Description (Continued)

Super Idle Line State

The Line State Detector recognizes the incoming data to be

in the Super Idle Line State upon the reception of 8 consec-

utive Idle symbol pairs nominally (plus 1 symbol pair).

The Super Idle Line State is used to insure synchronization

of PCM signalling.

No Signal Detect

The Line State Detector recognizes the incoming data to be

in the No Signal Detect state upon the deassertion of the

Signal Detect signal or lack of internal clock detect from the

Clock Recovery Module, and reception of 8 Quiet symbol

pairs nominally. No Signal Detect indicates that the incom-

ing link is inactive. This is the same as receiving Quiet Line

State (QLS).

Master Line State

The Line State Detector recognizes the incoming data to be

in the Master Line State upon the reception of eight consec-

utive Halt-Quiet symbol pairs nominally (plus up to 2 symbol

pairs in start up cases).

The Master Line State is used in the handshaking sequence

of the PHY Connection Management process.

Halt Line State

The Line State Detector recognizes the incoming data to be

in the Halt Line State upon the reception of eight consecu-

tive Halt symbol pairs nominally (plus up to 2 symbol pairs in

start up cases).

The Halt Line State is used in the handshaking sequence of

the PHY Connection Management process.

Quiet Line State

The Line State Detector recognizes the incoming data to be

in the Quiet Line State upon the reception of eight consecu-

tive Quiet symbol pairs nominally (plus up to 9 bits of 0 in

start up cases).

The Quiet Line State is used in the handshaking sequence

of the PHY Connection Management process.

Noise Line State

The Line State Detector recognizes the incoming data to be

in the Noise Line State upon the reception of 16 noise sym-

bol pairs without entering any known line state.

The Noise Line State indicates that data is not being re-

ceived correctly.

Line State Unknown

The Line State Detector recognizes the incoming data to be

in the Line State Unknown state upon the reception of 1

inconsistent symbol pair (i.e. data that is not expected). This

may signify the beginning of a new line state.

Line State Unknown indicates that data is not being re-

ceived correctly. If the condition persists the Noise Line

State (NLS) may be entered.

ELASTICITY BUFFER

The Elasticity Buffer performs the function of a ‘‘variable

depth’’ FIFO to compensate for phase and frequency clock

skews between the Receive Clock (RXCg) and the Local

Byte Clock (LBC).

Bit 5 (EBOU) of the Receive Condition Register B (RCRB) is

set to 1 to indicate an error condition when the Elasticity

Buffer cannot compensate for the clock skew.

The Elasticity Buffer will support a maximum clock skew of

50 ppm with a maximum packet length of 4500 bytes.

To make up for the accumulation of frequency disparity be-

tween the two clocks, the Elasticity Buffer will insert or de-

lete Idle symbol pairs in the preamble. Data is written into

the byte-wide registers of the Elasticity Buffer with the Re-

ceive Clock, while data is read from the registers with the

Local Byte Clock.

The Elasticity Buffer will recenter (i.e. set the read and write

pointers to a predetermined distance from each other) upon

the detection of a JK or every four byte times during PHY

Invalid (i.e. MLS, HLS, QLS, NLS, NSD) and Idle Line State.

The Elasticity Buffer is designed such that a given register

cannot be written and read simultaneously under normal op-

erating conditions. To avoid metastability problems, the EB

overflow event is flagged and the data is tagged before the

over/under run actually occurs.

LINK ERROR DETECTOR

The Link Error Detector provides continuous monitoring of

an active link (i.e. during Active and Idle Line States) to

insure that it does not exceed the maximum Bit Error Rate

requirement as set by the ANSI standard for a station to

remain on the ring.

Upon detecting a link error, the internal 8-bit Link Error Mon-

itor Counter is decremented. The start value for the Link

Error Monitor Counter is programmed through the Link Error

Threshold Register (LETR). When the Link Error Monitor

Counter reaches zero, bit 4 (LEMT) of the Interrupt Condi-

tion Register (ICR) is set to 1. The current value of the Link

Error Monitor Counter can be read through the Current Link

Error Count Register (CLECR). For higher error rates the

current value is an approximate count because the counter

rolls over.

There are two ways to monitor Link Error Rate: polling and

interrupt.

Polling

The Link Error Monitor Counter can be set to a large value,

like FF. This will allow for the greatest time between polling

the register. This start value is programmed through the Link

Error Threshold Register (LETR).

Upon detecting a link error, the Line Error Monitor Counter

is decremented.

The Host System reads the current value of the Link Error

Monitor Counter via the Current Link Error Count Register

(CLECR). The Counter is then reset to FF.

Interrupt

The Link Error Monitor Counter can be set to a small value,

like 5 to 10. This start value is programmed through the Link

Error Threshold Register (LETR).

Upon detecting a link error, the Line Error Monitor Counter

is decremented. When the counter reaches zero, bit 4

(LEMT) of the Interrupt Condition Register (ICR) is set to 1,

and the interrupt signal goes low, interrupting the Host Sys-

tem.

Miscellaneous Items

When bit 0 (RUN) of the Mode Register (MR) is set to zero,

or when the PLAYERadevice is reset through the Reset

pin (ERST), the internal signal detect line is internally

forced to zero and the Line State Detector is set to Line

State Unknown and No Signal Detect.

3.0 Functional Description (Continued)

3.3 TRANSMITTER BLOCK

The Transmitter Block accepts 10-bit bytes consisting of

8 bits data, 1 bit parity, and 1 bit control information, from

the Configuration Switch.

The Transmitter Block performs the following operations:

#Encodes the data from 4B to 5B coding.

#Filters out code violations from the data stream.

#Is capable of generating Idle, Master, Halt, Quiet, or oth-

er user defined symbol pairs.

#Converts the data stream from NRZ to NRZI for trans-

mission.

#Serializes data.

During normal operation, the Transmitter Block presents se-

rial data to a PMD transmitter.

While in Internal Loopback mode, the Transmitter Block

presents serial data to the Receiver Block. While in the Ex-

ternal Loopback mode, the Transmitter Block presents seri-

al data to the Clock Recovery Module.

The Transmitter Block consists of the following functional

blocks:

Data Registers

Parity Checker

4B/5B Encoder

Repeat Filter

Smoother

Line State Generator

Injection Control Logic

Shift Register

NRZ to NRZI Encoder

See

Figure 3-3

, Transmitter Block Diagram.

TL/F/11708– 5

FIGURE 3-3. Transmitter Block Diagram

3.0 Functional Description (Continued)

DATA REGISTERS

Data from the Configuration Switch is stored in the Data

Registers. The 10-bit byte-wide data consists of a parity bit,

a control bit, and two 4-bit data symbols as shown below.

b9 b8 b7 b0

Parity Bit Control Bit Data Bits

FIGURE 3-4. Byte-Wide Data

The parity is odd parity. The control bit determines whether

the Data bits represent Data or Control information. When

the control bit is 0 the Data field is interpreted as data and

when it is 1 the field is interpreted as control information

according to the National Semiconductor control codes.

PARITY CHECKER

The Parity Checker verifies that the parity bit in the Data

The parity is enabled and disabled through bit 6 (PRDPE) of

the Current Transmit State Register (CTSR).

If a parity error occurs, the Parity Checker will set bit 0 (DPE)

in the Interrupt Condition Register (ICR) and report the error

to the Repeat Filter.

4B/5B ENCODER

The 4B/5B Encoder converts the two 4-bit data symbols

from the Configuration Switch into their respective 5-bit

codes.

See Table 3-2 for the Symbol Encoding list.

TABLE 3-2. 4B/5B Symbol Encoding

Symbol 4B Code 5B Code

0 0000 11110

1 0001 01001

2 0010 10100

3 0011 10101

4 0100 01010

5 0101 01011

6 0110 01110

7 0111 01111

8 1000 10010

9 1001 10011

A 1010 10110

B 1011 10111

C 1100 11010

D 1101 11011

E 1110 11100

F 1111 11101

N 0000 11110 or

11111

JK (Starting 1101 11000 and

Delimiter) 10001

T (Ending 0100 or 01101

Delimiter) 0101

R (Reset) 0110 00111

Note: The upper group of symbols are sent with the Control/Data pin set to

Data, while the bottom grouping of symbols are sent with the Control/Data

pin set to Control.

REPEAT FILTER

The Repeat Filter is used to prevent the propagation of

code violations to the downstream station.

Upon receiving violations in data frames, the Repeat Filter

replaces them with two Halt symbol pairs followed by Idle

symbols. Thus the code violations are isolated and recov-

ered at each link and will not be propagated throughout the

entire ring.

3.0 Functional Description (Continued)

TL/F/11708– 6

FIGURE 3-5. Repeat Filter State Diagram

Note: Inputs to the Repeat Filter state machine are shown above the transition lines, while outputs from the state machine are shown below the transition lines.

Note: Abbreviations used in the Repeat Filter State Diagram are shown in Table 3-3.

3.0 Functional Description (Continued)

TABLE 3-3. Abbreviations used in the

Repeat Filter State Diagram

FÐIDLE: Force IdleÐtrue when not in Active

Transmit Mode.

W: Represents the symbols R, or S, or T

ETPARITY: Parity error

nn : Data symbols (for C e0 in the PHY-MAC

interface)

N: Data portion of a control and data symbol

mixture

X: Any symbol (i.e. don’t care)

VÊ: Violation symbols or symbols inserted by

the Receiver Block

IÊ: Idle symbols or symbols inserted by the

Receiver Block

ALSZILSZ: Active Line State or Idle Line State (i.e.

PHY Invalid)

EALSZILSZ: Not in Active Line State nor in Idle Line

State (i.e. PHY Valid)

H: Halt Symbol

R: Reset Symbol

S: Set Symbol

T: Frame ending delimiter

JK: Frame start delimiter

I: Idle symbol (Preamble)

V: Code violations

The Repeat Filter complies with the FDDI standard by ob-

serving the following (see

Figure 3-5

1. In Repeat State, violations cause transitions to Halt State

and two Halt symbol pairs are transmitted (unless JK or Ix

occurs) followed by transition to Idle State.

2. When Ix is encountered, the Repeat Filter goes to the Idle

State, during which Idle symbol pairs are transmitted until

a JK is encountered.

3. The Repeat Filter goes to the Repeat State following a JK

from any state.

The END State, which is not part of the FDDI PHY standard,

allows an R or S prior to a T within a frame to be recognized

as a violation. It also allows NT to end a frame as opposed

to being treated as a violation.

SMOOTHER

The Smoother is used to keep the preamble length of a

frame to a minimum of 6 Idle symbol pairs.

Idle symbols in the preamble of a frame may have been

added or deleted by each station to compensate for the

difference between the Receive Clock and its Local Clock.

The preamble needs to be maintained at a minimum length

to allow stations enough time to complete processing of one

frame and prepare to receive another. Without the Smooth-

er function, the minimum preamble length (6 Idle symbol

pairs) cannot be maintained as several stations may con-

secutively delete Idle symbols.

The Smoother attempts to keep the number of Idle symbol

pairs in the preamble at 7 by:

#Deleting an Idle symbol pair in preambles which have

more than 7 Idle symbol pairs

and/or

#Inserting an idle symbol pair in preambles which have

less than 7 idle symbol pairs (i.e. Extend State).

The Smoother Counter starts counting upon detecting an

Idle symbol pair. It stops counting upon detecting a JK sym-

bol pair.

Figure 3-6

describes the Smoother state diagram.

3.0 Functional Description (Continued)

LINE STATE GENERATOR

The Line State Generator allows the transmission of the

PHY Request data and can also generate and transmit Idle,

Master, Halt, or Quiet symbol pairs which can be used to

implement the Connection Management procedures as

specified in the FDDI Station Management (SMT) standard

document.

The Line State Generator is programmed through Transmit

bits 0 to 2 (TMk2:0l) of the Current Transmit State Regis-

ter (CTSR).

Based on the setting of these bits, the Transmitter Block

operates in a Transmit Mode where the Line State Genera-

tor overwrites the Repeat Filter and Smoother outputs.

See INJECTION CONTROL LOGIC section for a listing of

the injection Transmit Modes.

Table 3-4 describes the Transmit Modes.

TABLE 3-4. Transmit Modes

Transit Mode Behavior

Active Transmit Mode Transmit data that comes

from Configuration Switch

Off Transmit Mode Transmit Quiet symbol

pairs and disable the PMD

Transmitter

Idle Transmit Mode Transmit Idle symbol pairs

Master Transmit Mode Transmit Halt-Quiet

symbol pairs

Quiet Transmit Mode Transmit Quiet symbol

pairs

Reserved Transmit Mode Reserved for future use. If

Mode selected, Quiet

symbol pairs will be

transmitted.

Halt Transmit Mode Transmit Halt Symbol

pairs

Notes: TL/F/11708– 7

SE: Smoother Enable

C: Preamble Counter

FÐIDLE: ForceÐIdle (Stop or ATM)

Xn: Current Byte

Xn–1: Previous Byte

W: RST

FIGURE 3-6. Smoother State Diagram

3.0 Functional Description (Continued)

INJECTION CONTROL LOGIC

The Injection Control Logic replaces the data stream with a

programmable symbol pair. This function is used to transmit

data other than the normal data frame or Line States. The

injection modes can be used for station diagnostic software.

The Injection Symbols overwrite the Line State Generator

(Transmit Modes) and the Repeat Filter and Smoother out-

puts.

These programmable symbol pairs are stored in the Injec-

tion Symbol Register A (ISRA) and Injection Symbol Regis-

ter B (ISRB). The Injection Threshold Register (IJTR) deter-

mines where the Injection Symbol pair will replace the data

symbols.

The Injection Control Logic is programmed through the bits

0 and 1 (ICk1:0l) of the Current Transmit State Register

(CTSR) to one of the following Injection Modes (see

Figure

3-7

1. No Injection (i.e. normal operation)

2. One Shot

3. Periodic

4. Continuous

In the No Injection mode, the data stream is transmitted

unchanged.

In the One Shot mode, ISRA and ISRB are injected once on

the nth byte after a JK, where n is the programmed value

specified in the Injection Threshold Register.

In the Periodic mode, ISRA and ISRB are injected every nth

symbol.

In the Continuous mode, all data symbols are replaced with

the content of ISRA and ISRB. This is the same as periodic

mode with IJTRe0.

SHIFT REGISTER

The Shift Register converts encoded parallel data to serial

data. The parallel data is clocked into the Shift Register by

the Local Byte Clock (LBC1), and clocked out by the Trans-

mit Bit Clock (TXCg) (externally available on the DP83257.)

NRZ TO NRZI ENCODER

The NRZ to NRZI Encoder converts the serial Non-Return-

To-Zero data to Non-Return-To-Zero-Invert-On-One format.

This function can be enabled and disabled through bit 6

(TNRZ) of the Mode Register (MR). When programmed to

‘‘0’’, it converts the bit stream from NRZ to NRZI. When

programmed to ‘‘1’’, the bit stream is transmitted NRZ.

One Shot (Notes 1,3)

TL/F/11708– 8

Periodic (Notes 2,3)

TL/F/11708– 9

Continuous (Note 3)

TL/F/11708– 10

Note 1: In one shot, when ne0, the JK is replaced

Note 2: In periodic, when ne0, all symbols are replaced.

Note 3: Max value on ne255.

FIGURE 3-7. Injection Modes

3.0 Functional Description (Continued)

3.4 CONFIGURATION SWITCH

The Configuration Switch consists of a set of multiplexers

and latches which allow the PLAYERadevice to configure

the data paths without any external logic. The Configuration

Switch is controlled through the Configuration Register

(CR).

The Configuration Switch has four internal buses: the

AÐRequest bus, the BÐRequest bus, the Receive bus, and

the PHYÐInvalid bus. The two Request buses can be driv-

en by external input data connected to the external PHY

Port interface. The Receive bus is internally connected to

the Receive Block of the PLAYERadevice, while the

PHYÐInvalid bus has a fixed 10-bit SMT PHY Invalid con-

nection (LSU) pattern (1 0011 1010), which is useful during

the connection process.

The configuration switch also has three internal multiplex-

ers, each can select any of the four buses to connect to its

respective data path. The first two are PHY Port interface

output data paths, AÐIndicate and BÐIndicate, that can

drive output data paths of the external PHY Port interface.

The third output data path is connected internally to the

Transmit Block.

The Configuration Switch is the same on the DP83256 de-

vice, the DP83256-AP device, and the DP83257 device.

However, the DP83257 has two PHY Port interfaces con-

nected to the Configuration Switch, whereas the DP83256

and DP83256-AP have one set of PHY port interfaces. The

DP83257 uses the AÐRequest and AÐIndicate paths as

one PHY Port interface and the BÐRequest and BÐIndi-

cate paths as the other PHY Port interface (See

Figure 3-8

The DP83256 and DP83256-AP, having one port interface,

use the BÐRequest and AÐIndicate paths as its external

port. The AÐRequest and BÐIndicate paths of the

DP83256 and DP83256-AP are null connections and are not

used by the device (See

Figure 3-9

TL/F/11708– 11

FIGURE 3-8. Configuration Switch

Block Diagram for DP83257

TL/F/11708– 12

FIGURE 3-9. Configuration Switch

Block Diagram for DP83256

and DP83256-AP

3.0 Functional Description (Continued)

STATION CONFIGURATIONS

Single Attach Station (SAS)

The Single Attach Station can be connected to either the

Primary or Secondary ring via a Concentrator. Only 1 MAC

is needed in a SAS.

The DP83256, DP83256-AP, and DP83257 can be used in a

Single Attach Station. The DP83256 and DP83256-AP can

be connected to the MAC via its only PHY Port interface.

The DP83257 can be connected to the MAC via either one

of its 2 PHY Port Interfaces.

See

Figure 3-10

and

Figure 3-11

TL/F/11708– 13

FIGURE 3-10. Single Attach Station

Using the DP83256 or DP83256-AP

TL/F/11708– 14

FIGURE 3-11. Single Attachment Station (SAS)

Using the DP83257

Dual Attach Station(DAS)

A Dual Attach Station can be connected directly to the dual

ring, or, optionally to a concentrator. There are two types of

Dual Attach Stations: DAS with a single MAC and DAS with

two MAC layers. See

Figure 3-12

and

Figure 3-13

Two DP83256 or DP83256-AP parts can be connected to-

gether to build a Dual Attach Station, however this configu-

ration does not support the optional ThruÐB configuration.

When the optional ThruÐB configuration is desired, it is rec-

ommended that the DP83257 be used.

A DAS with a single MAC and two paths can be configured

as follows (see

Figure 3-12

#B Indicate data of PHYÐA is connected to A Request

input of PHYÐB. BÐRequest input of PHYÐA is con-

nected to A Indicate output of PHYÐB.

#The MAC can be connected to either the A Request in-

put and the A Indicate output of PHYÐAortheBRe-

quest input and the B Indicate output of PHYÐB.

A DAS with a single MAC and one path using the DP83256

or DP83256-AP can be configured as follows (see

Figure 3-

#BÐRequest input of PHYÐA is connected to A Indicate

output of PHYÐB.

#The MAC is connected to the B Request input of

PHYÐB and the AÐIndicate output of PHYÐA.

A DAS with dual MACs can be configured as follows (see

Figure 3-14

#B Indicate data of PHYÐA is connected to A Request

input of PHYÐB. BÐRequest input of PHYÐA is con-

nected to A Indicate output of PHYÐB.

#MACÐ1 is connected to the BÐIndicate output and the

BÐRequest Input of PHYÐB.

#MACÐ2 is connected to the AÐIndicate output and the

AÐRequest Input of PHYÐA.

3.0 Functional Description (Continued)

TL/F/11708– 15

FIGURE 3-12. Dual Attachment Station (DAS), Single MAC (DP83257)

TL/F/11708– 16

FIGURE 3-13. Dual Attachment Station (DAS), Single MAC (DP83256/56-AP)

TL/F/11708– 17

FIGURE 3-14. Dual Attachment Station (DAS), Dual MACs

3.0 Functional Description (Continued)

CONCENTRATOR CONFIGURATIONS

There are 2 types of concentrators: Single Attach and Dual

Attach. These concentrators can be designed with or with-

out MAC(s). The configuration is determined based upon its

type and the number of active MACs in the concentrator.

Using the PLAYERadevice, a concentrator can be built

with many different configurations without any external log-

ic.

The DP83256, DP83256-AP, and DP83257 can be used to

build a Single Attach concentrator.

See Application Note AN-675, Designing FDDI concentra-

tors and Application Note AN-741, Differentiating FDDI con-

centrators for further information.

Concepts

A concentrator is comprised of 2 parts: the Dual Ring Con-

nect portion and the Master Ports.

The Dual Ring Connection portion connects the concentra-

tor to the dual ring directly or to another concentrator. If the

concentrator is connected directly to the dual ring, it is a

part of the ‘‘Dual Ring of Trees’’. If the concentrator is con-

nected to another concentrator, it is a ‘‘Branch’’ of the

‘‘Dual Ring of Trees’’.

The Master Ports connect the concentrator to its ‘‘Slaves’’,

or S-class, Single Attach connections. A slave could be a

Single Attach Station or another concentrator (thus forming

another Branch of the Dual Ring Tree).

When a MAC in a concentrator is connected to the primary

or secondary ring, it is required to be situated at the exit port

of that ring (i.e. its PHÐIND is connected to the IND Inter-

face of the last Master Port in the concentrator (PHYÐMn)

that is connected to that ring).

A concentrator can have two MACs, one connected to the

primary ring and one to the secondary ring. In addition, rov-

ing MACs can be included in the concentrator configuration.

A roving MAC can be used to test the stations connected to

the concentrator before allowing them to join the dual ring.

This may require external multiplexers, if used in conjunc-

tion with two other MAC layers.

Single Attach Concentrator

A Single Attach concentrator is a concentrator that has only

one PHY at the dual ring connect side. It cannot, therefore,

be connected directly to the dual ring. A Single Attach con-

centrator is a branch to the dual ring tree. It is connected to

the ring as a slave of another concentrator.

Multiple Single Attach concentrators can be connected to-

gether hierarchically to build a multiple levels of branches in

a dual ring.

The Single Attach concentrator can be connected to either

the primary or secondary ring depending on the connection

with its concentrator (the concentrator that it is connected

to as a slave).

Figure 3-15

shows a Single Attach concentrator with a sin-

gle MAC.

Dual Attach Concentrator

A Dual Attach concentrator is a concentrator that has two

PHYs on the dual ring connect side. It is connected directly

to the dual ring and is a part of the dual ring tree.

The Dual Attach concentrator is connected to both the pri-

mary and secondary rings.

Dual Attach Concentrator with Single MAC

Figure 3-16

shows a Dual Attach concentrator with a single

MAC.

Because the concentrator has one MAC, it can only transmit

and receive frames on the ring to which the MAC is con-

nected. The concentrator can only repeat frames on the

other ring.

Dual Attach Concentrator with Dual MACs

Figure 3-17

shows a Dual Attach concentrator with dual

MACs.

Because the concentrator has two MACs, it can transmit

and receive frames on both the primary and secondary

rings.

3.0 Functional Description (Continued)

TL/F/11708– 18

FIGURE 3-15. Single Attach Concentrator (SAC), Single MAC

TL/F/11708– 19

FIGURE 3-16. Dual Attach Concentrator (DAC), Single MAC

TL/F/11708– 20

FIGURE 3-17. Dual Attach Concentrator (DAC), Dual MACs

3.0 Functional Description (Continued)

3.5 CLOCK GENERATION MODULE

The Clock Generation Module is an integrated phase locked

loop that generates all of the required clock signals for the

PLAYERadevice and the rest of an FDDI system from a

single 12.5 MHz reference.

The Clock Generation Module features:

#High precision clock timing generated from a single

12.5 MHz reference.

#Multiple precision phased (8 ns/16 ns) 12.5 MHz Local

Byte Clocks to eliminate timing skew in large multi-board

concentrator configurations.

#LBC timing which is insensitive to loading variations over

a wide range (20 pF to 70 pF) of LBC loads.

#A selectable dual frequency system clock.

#Low clock edge jitter, due to high VCO stability.

The Clock Generation Module is comprised of 6 main func-

tional blocks:

Reference Selector

Phase Comparator

Loop Filter

250 MHz Voltage Controlled Oscillator

Output Phasing and Divide by 10

See

Figure 3-18

, Clock Generation Module Block Diagram.

REFERENCE SELECTOR

The Reference Selector block allows the user to choose

between 2 sources for the Clock Generation Module’s

12.5 MHz reference clock.

The simplest reference clock source option is to use an

external 12.5 MHz reference signal fed into the REFÐIN

input. This input can come from a crystal oscillator module

or from a Local Byte Clock generated by another PLAYERa

device. Using the appropriate crystal oscillator ensures cor-

rect operating frequency without having to adjust any dis-

crete components.

Using an LBC clock from another PLAYERadevice allows

one PLAYERadevice to create a master clock to which

other PLAYERadevices in a system can be synchronized.

Another reference clock source option is a local 12.5 MHz

crystal circuit. An example crystal circuit with component

values is shown in

Figure 3-19.

This circuit is designed to

operate with a crystal that has a CLof 15 pF. The capacitor

values may need to be slightly adjusted for an individual

application to accomodate differences in parasitic loading.

The REFÐSEL signal selects between the two references.

Component Values

Crystal: 12.50000 MHz

R: 270X5%

CISO: 56 pF (1%)

CIN: 54 pF (1%)

COUT: 54 pF (1%)

TL/F/11708– 22

FIGURE 3-19. Crystal Circuit

PHASE COMPARATOR

The Phase Comparator uses two signal inputs: the selected

12.5 MHz reference from the Reference Select Block and a

Local Byte Clock that has been selected for the feedback

input, FBKÐIN. Typically, LBC1 is used as the feedback

clock.

The Phase Comparator generates a pulse of current that is

proportional to the phase difference between the two sig-

nals. The current pulses are used to charge and discharge a

control voltage on the internal Loop Filter. This control volt-

age is used to minimize the phase difference between the

two signals.

LOOP FILTER

The Loop Filter is a simple internal filter made up of one

capacitor in parallel with a serial capacitor and resistor com-

bination. One end of the filter is connected to Ground and

the other node is driven by the Phase Comparator and con-

trols the internal 250 MHz Voltage Controlled Oscillator.

This node can be examined for diagnostic purposes on the

LPFLTR pin when the FLTREN bit of the CGMREG register

is enabled. The LPFLTR pin is provided for diagnostic pur-

poses only and should not be connected in any application.

TL/F/11708– 21

FIGURE 3-18. Clock Generation Module Block Diagram

3.0 Functional Description (Continued)

The voltage on the Loop Filter is set by the current pulses

generated by the Phase Comparator. The voltage on the

Loop Filter node controls the frequency of the 250 MHz

VCO.

250 MHZ VOLTAGE CONTROLLED OSCILLATOR (VCO)

The internal Voltage Controlled Oscillator is a low gain VCO

whose primary frequency of oscillation centers around

250 MHz. The VCO produces little clock jitter due to its

exceptional stability under all circumstances.

The VCO’s output frequency is proportional to the voltage

on the Loop Filter node.

OUTPUT PHASING

The Output Phasing block is a precision clock division circuit

that produces clock signals of 4 distinct frequencies. Within

the 12.5 MHz frequency, 5 clock signals with selectable 8 ns

or 16 ns phase difference are produced.

The following clock signals are produced:

System Clock (CLK16/CLK32)

Local Symbol Clock (LSC)

Local Byte Clocks 1–5 (LBCn) (Divide by 10)

System Clock (CLK16/CLK32)

The System Clock is provided as an extra set of clock fre-

quencies that may be used as a clock for non-FDDI chipset

portions of a system or as a higher frequency System Inter-

face clock for the MACSI device. This clock is derived by

dividing the 125 MHz clock by 8 or 4 times.

The frequency is selectable through the CLKSEL bit of the

MODE2 register. The output has built-in glitch suppression

so that changing the CLKSEL bit will not result in glitches

appearing at the output.

Local Symbol Clock (LSC)

The Local Symbol Clock is a 40% HIGH/60% LOW duty

cycle clock provided for use by the MACSI device and any

external logic that needs to be synchronized to the Symbol

timing.

This clock is derived by dividing the 125 MHz clock by 5.

Local Byte Clocks 1–5 (LBCn)

The Local Byte Clocks are provided for use by the MACSI

device, by any external logic that needs to be synchronized

to the Byte timing, and for use in concentrators to synchro-

nize the timing between multiple PLAYERadevices.

These clocks are derived by dividing the 125 MHz clock by

10. The different phase relationships between the LBCs are

achieved by tapping off of different outputs of a Johnson

counter inside the Output Phasing block.

The phase relationship (separation by 8 ns or 16 ns) of the

LBCs is selected using the PHÐSEL pin.

One of the LBCs must be used as the source of the feed-

back input, FBKÐIN, which requires a 12.5 MHz frequency.

When the PLAYERadevice is using a crystal as a refer-

ence it does not matter which LBC is used as the feedback

input. Typically the least loaded LBC is used. However,

when using an external reference that is supplied by anoth-

er PLAYERadevice, it is important to select the LBC that

keeps your system properly synchronized. Typically, all de-

vices will use LBC1 as the feedback input.

3.6 STATION MANAGEMENT SUPPORT

The Station Management Support Block provides a number

of useful features to simplify the implementation of the Con-

nection Management (CMT) portion of SMT.

These features eliminate the most severe CMT response

time constraints imposed by the PCÐReact and CFÐReact

times. The many integrated counters and timers also elimi-

nate the need for additional external devices.

The following CMT features are supported:

#PCÐReact

#CFÐReact

#Auto Scrubbing (TCF Timer)

#Timer, Idle Detection (TID Timer)

#Noise Event Counter (TNE Timer)

#Link Error Monitor (LEM Counter)

PCÐREACT

PCÐReact is one of the timing restrictions imposed by Con-

nection Management (CMT). It is one of the two most crit-

ical timing restrictions imposed (the other being CFÐRe-

act.)

The ANSI SMT standard states that ‘‘PCÐReact is the max-

imum time for PCM [Physical Connection Management]to

make a state transition to PCÐBreak when QLS, a fault

condition, or PCÐStart signal is present. This maximum

time also places a limit on the time to react to a PCÐStop

signal. This limitation does not apply to any other PCM tran-

sitions.’’ PCÐReact puts a sharp time limit on how long it

takes to transition to the PCÐBreak state and transmit the

correct line state when a PCÐBreak transition is required.

The range for the timer is PCÐReact s3.0 ms and has a

default value equal to 3.0 ms.

The PLAYERadevice contains a Trigger Definition Regis-

ter and a set of CMT Condition Registers that can be used

to satisfy the PCÐReact timing.

The Trigger Definition Register (TDR) controls two func-

tions. First, it allows the selection of the line state(s) on

which to trigger (SILS, MLS, HLS . . . ). For PCÐReact, the

line states used would be the ones that caused a transition

to the PCÐBreak state from the current PCM state.

Second, it allows specification of a line state to be transmit-

ted when the trigger condition is met. For PCÐReact, this is

the line state that needs to be transmitted when a transition

to the PCÐBreak state occurs, which is Quiet Line State

(QLS).

The set of CMT Condition registers controls interrupt gener-

ation when a trigger condition occurs. The CMT Condition

CMT Condition Comparison Register (CMTCCR), and a

CMT Condition Mask Register (CMTCMR).

Line state triggering for PCÐReact is enabled by selecting

line states to trigger on from the Trigger Definition Register

(TDR) bits 3-7.

The Trigger Condition Occurred (TCO) bit of the CMTCR is

automatically set when the trigger condition specified by the

TDR register is met.

The line state specified by the Trigger Definition Register

(TDR) bits 0–2 is then loaded into the Current Transmit

Mode Register (CTSR), causing the line state to be trans-

mitted.

3.0 Functional Description (Continued)

If the TCO Mask (TCOM) bit of the CMTCMR is set, then

whenever the CMTCR.TCO bit becomes set the Receive

Condition Register B’s Connection Service Event

(RCRB.CSE) bit will be set. This allows an interrupt to be

generated for the trigger event.

As an example, suppose the PCM state machine is in the

ACTIVE state. From this state, if a Halt Line State (HLS) or

Quiet Line State (QLS) is detected, or the Noise Threshold

is reached, the state machine must move to the PCÐBreak

state and begin transmitting QLS. To implement this behav-

ior when the PCÐACTIVE state is entered, set

TDR.TTM2–0 to 110 (Quiet Transmit), set TDR.TOHLS,

TDR.TOQLS, and TDR.TONT and reset all other bits (TO-

SILS and TOMLS). Also set CMTCMR.TCOM if an interrupt

is desired.

CFÐREACT

CFÐReact is one of the timing restrictions imposed by Con-

nection Management (CMT). It is one of the two most crit-

ical timing restrictions imposed (the other being

PCÐReact).

The ANSI SMT standard states that ‘‘CFÐReact is the max-

imum time for CFM [Configuration Management]to recon-

figure to remove a non-Active connection from the token

path.’’

The range for the timer is CFÐReact s3.0 ms and has a

default value equal to 3.0 ms.

The PLAYERadevice contains a Trigger Transition Config-

uration Register and a set of CMT Condition Registers that

can be used to satisfy the CFÐReact timing.

he Trigger Transition Configuration Register (TTCR) holds

the new configuration switch settings to be loaded into the

Configuration Register (CR) when a trigger condition occurs.

Enabling line state triggering with the Trigger Definition Reg-

ister (TDR) bits 3–7 also enables the CFÐReact response.

This means that whenever trigger conditions are actively

used for PCÐReact, the value of the TTCR register will be

used also. This implies that it either must always then be

loaded with the current configuration setting, causing no

change to the CR, or it must be loaded with the appropriate

value to accommodate the CFÐReact function.

The Trigger Transition Configuration Register (TTCR) must

be set the configuration desired when the trigger condition

occurs. When the trigger condition occurs the value of this

ing this time writes to the CR are inhibited.

To continue the example from the PCÐReact description,

suppose that when in the ACTIVE state for the PCM state

machine, the CFM state machine is also in the THRUÐA

state. If trigger conditions are enabled via the

CMTCMR.TCOM bit and it is desired to not implement CFÐ

React, TTCR must be set to the present value of CR. If it is

desired to not implement CFÐReact then TTCR should be

set to the value which would change the configuration to the

WRAP state. The wrap conditions WRAPÐA or WRAPÐB

depend on which PHY gets reconfigured.

AUTO SCRUBBING

Auto Scrubbing is an additional CMT feature that further

enhances the automatic configuration switch setting in or-

der to meet the CFÐReact timing. When enabled, Auto

Scrubbing causes 2 PHYÐInvalid symbols followed by

Scrub Symbol pairs (Idles) to be sourced for a user select-

able duration (the scrubbing time) after a trigger condition

(the same one used for PCÐReact and CFÐReact) occurs

and prior to a change in the configuration switch setting on

all indicate ports that will be changed.

Auto Scrubbing is enabled by setting the Enable Scrubbing

on Trigger Conditions (ESTC) bit of Mode Register 2

(MODE2).

The Scrub Timer Threshold Register (STTR) defines the du-

ration of the scrubbing, which can last up to approximately

10ms. The Scrub Timer Value Register (STVR) can be used

to examine a snapshot of the upper 8 bits of the STTR

TIMER, IDLE DETECTION

The Idle Detection Timer is required to flag the continued

presence of the Idle Line State for a duration of 8 Idle Sym-

bol pairs plus 1 symbol pair.

This feature is implemented in the Receiver Block by the

Super Idle Line State (SILS).

NOISE EVENT COUNTER

The Noise Event Counter can be used to time the duration

between Noise Events (which are described in detail below)

and to count frame sizes. The first feature is the most often

recognized, but the second is often overlooked and can

lead to potential difficulty if not properly set.

The Noise Event Counter is implemented as a pair of down

counters: one the actual Noise Counter and the other a

Noise Counter Prescaling value. The Noise Threshold Reg-

ister (NTR) and the Noise Prescale Threshold Register

(NPTR) can be programmed to the counter’s initial value

while the Current Noise Count Register (CNCR) and the

Current Noise Prescale Count Register (CNPCR) provide a

snapshot of the actual counter.

The Noise Event Counter decrements whenever a Noise

Line State (NLS), Line State Unknown (LSU), or Active Line

State (ALS) is received and has its start value reloaded

whenever it receives Halt Line State (HLS), Idle Line State

(ILS), Master Line State (MLS), Quiet Line State (QLS), or

No Signal Detect (NSD). The Noise Event Counter is also

reset for a Start or End Delimiter. This means the Noise

counter increments for bad events as well as for every data

symbol in a frame. Should the Noise Counter expire, it indi-

cates that a new line state (including ALS) has not been

entered for NTÐMAX time. This indicates that either a

frame is too long or that noise is being received.

For this reason it is important to choose a value for the

counter that is larger than the longest frame of 4500 bytes.

The ANSI SMT specification recommends a value for

NTÐMAX of 1.3ms for the noise threshold.

A Noise Event is defined as follows:

A noise event is a noisebyte, or a byte of data which is not in

line with the current line state, indicating error or corruption.

3.0 Functional Description (Continued)

TABLE 3-5. Noise Event Description

Noise Event e[SD #ECD]a

[SD #CD #PI #E(II aJK aAB)]a

[SD #CD #EPI #(PB eII) #AB]

Where:

#eLogical AND

Logical OR

EeLogical NOT

SD eSignal Detect

CD eClock Detect

PB ePrevious Byte

PLS ePrevious Line State

PI ePHY Invalid eHLS aQLS

aMLS aNLS aÀ

ULS #[PLS

e(ALS aILS)]Ó

ILS eIdle Line State

ALS eActive Line State

ULS eUnknown Line State

HLS eHalt Line State

QLS eQuiet Line State

MLS eMaster Line State

NLS eNoise Line State

ULS eUnknown Line State

IeIdle symbol

JeFirst symbol of start delimiter

KeSecond symbol of start

delimiter

ReReset symbol

SeSet symbol

TeEnd Delimiter

AenaRaSaT

BenaRaSaTaI

neany data symbol

LINK ERROR MONITOR

Link Error Monitoring is accomplished in the PLAYERade-

vice through the Link Error Monitor Counter. The initial value

of this down counter is set using the Link Error Threshold

with the Current Link Error Count Register (CLECR).

A Link Error is defined as follows:

TABLE 3-6. Link Error Event Description

Link Error [ALS #(IEIaxV aVx aHEH)]a

[ALS #ESD]a[ILS #E(II aJK)]a

Event e

[ILS #ESD)]a[ULS #(PLSeALS) #

LinkÐErrorÐFlag #ESB #E(HH aHI

aII aJK)]

Set LinkÐErrorÐFlag e[ALS #(HH aNH aRH a

SH aTH)]

Clear LinkÐErrorÐFlag e[ALS #JK]a

[ILS #JK]a[ULS #(PLSeALS #LinkÐ

ErrorÐFlag #ESB #E(HH aHI aII a

JK)]

Where:

EeLogical NOT

Logical OR

#eLogical AND

ILS eIdle Line State

ALS eActive Line State

ULS eUnknown Line State

xeAny symbol

IeIdle symbol

HeHalt symbol

JeFirst symbol of start delimiter

KeSecond symbol of start

delimiter

VeViolation symbol

ReReset symbol

SeSet symbol

TeEnd delimiter symbol

NeData symbol converted to

0000 by the PLAYERadevice

Receiver Block in symbol pairs

that contain a data and a control

symbol

PLS ePrevious Line State

SD eSignal Detect

SB eStuff Byte: Byte inserted by EB

before a JK symbol pair for

recentering or due to off-axis JK

3.0 Functional Description (Continued)

3.7 PHY-MAC INTERFACE

NATIONAL BYTE-WIDE CODE

The PLAYERadevice outputs the National byte-wide code

from its PHY Port Indicate Output to the MAC device. Each

National byte-wide code may contain data or control codes

or the line state information of the connection. Table 3-7

lists all the possible outputs.

During Active Line State all data and control symbols are

being repeated to the PHY Port Indicate Output with the

exception of data in data-control mixture bytes. That data

symbol is replaced by zero. If only one symbol in a byte is a

control symbol, the data symbol will be replaced by 0000

and the whole byte will be presented as control code. Note

that the Line State Detector recognizes the incoming data

to be in the Active Line State upon reception of the Starting

Delimiter (JK symbol pair).

During Idle Line State any non Idle symbols will be reflected

as the code IÊuILS. If both symbols received during Idle Line

State are Idle symbols, then the Symbol Decoder generates

IÊkILS as its output. Note the coded Known/Unknown Bit

(b3) and the Last Known Line State (b2–0). The Receive

State is 4 bits long and it represents either the PHY Invalid

(0011) or the Idle Line State (1011) condition. The Known/

Unknown Bit shows if the symbols received match the line

state information in the last 3 bits.

During any line state other than Idle Line State or Active

Line State, the Symbol Decoder generates the code VÊkLS

if the incoming symbols match the current line state. The

symbol decoder generates VÊuLS if the incoming symbols

do not match the current line state.

TABLE 3-7. National Byte Wide Code

Current Line State Symbol 1 Symbol 2 National Code

Control Bit Data Control Bit Data Control Bit Data

ALS 0 n 0 n 0 n-n

ALS 0 n 1 C 1 N-C

ALS 1 C 0 n 1 C-N

ALS 1 C 1 C 1 C-C

ILS 1I 1I 1I

-k-LS

ILS 1 I x Not I 1 IÊ-u-LS

ILS x Not I 1 I 1 IÊ-u-LS

ILS x Not I x Not I 1 IÊ-u-LS

Stuff Byte during ILS x x x x 1 IÊ-k-ILS

Not ALS and Not ILS 1 M 1 M 1 VÊ-k-LS

Not ALS and Not ILS 1 M x Not M 1 VÊ-u-LS

Not ALS and Not ILS x Not M 1 M 1 VÊ-u-LS

Not ALS and Not ILS x Not M x Not M 1 VÊ-u-LS

Stuff Byte during Not ALS x x x x 1 VÊ-k-LS, VÊ-u-LS

or LÊ-u-ILS

EB Overflow/Underflow 1 0011 1011

SMTÐPI Connection (LSU) 1 0011 1010

Scrub Symbol Pair 1 1011 1000

Where:

neAny data symbol in À0, 1, 2 . . . FÓ

CeAny control symbol in ÀV, R, S, T, I, HÓ

Ne0000 eCode for data symbol in a data control mixture byte

IeIdle Symbol

MeAny symbol that matches the current line state

IÊe1011 eFirst symbols of the byte in Idle Line State

VÊe0011 ePHY Invalid

LS eLine State

ALS e000

ILS e001

NSD e010

MLS e100

HLS e101

QLS e110

NLS e111

ue1eIndicates symbol received does not match current line state

ke0eIndicate symbol received matches current line state

xeDon’t care

3.0 Functional Description (Continued)

National Byte-Wide Code Example

Incoming 5B Code Decoded 4B Code National Byte-Wide Code (w/o parity)

98765 43210 C 3210 C 3210 C 7654 3210

11111 11111 (II) 1 1010 1 1010 (II) 1 1011 0001 (IÊ-k-ILS)*

11111 11111 (II) 1 1010 1 1010 (II) 1 1011 0001 (IÊ-k-ILS)

11000 10001 (JK) 1 1101 1 1102 (JK) 1 1101 1101 (JK Symbols)

–––- –––- (xx) 0 ––– 0 ––– (xx) 0 ––– ––– (Data Symbols)

(More data Ð)

–––- –––- (xx) 0 ––– 0 ––– (xx) 0 ––– ––– (Data Symbols)

01101 00111 (TR) 1 0101 1 0110 (TR) 1 0101 0110 (T and R Symbols)

00111 00111 (RR) 1 0110 1 0110 (RR) 1 0110 0110 (Two R Symbols)

11111 11111 (II) 1 1010 1 1010 (II) 1 1010 1010 (Idle Symbols)

11111 11111 (II) 1 1010 1 1010 (II) 1 1011 0001 (IÊ-k-ILS)

00100 00100 (HH) 1 0001 1 0001 (HH) 1 1011 1001 (IÊ-u-ILS)

00100 00100 (HH) 1 0001 1 0001 (HH) 1 0011 0101 (VÊ-k-HLS)

11111 11111 (II) 1 1010 1 1010 (II) 1 0011 1101 (VÊ-u-HLS)

11111 11111 (II) 1 1010 1 1010 (II) 1 1011 0001 (IÊ-k-ILS)

*Assume the receiver is in the Idle Line State.

3.0 Functional Description (Continued)

3.8 PMD INTERFACE

The PMD Interface connects the PLAYERadevice to a

standard FDDI Physical Media Connection such as a fiber

optic transceiver or a copper twisted pair transceiver. It is a

125 MHz full duplex serial connection.

The DP83256 PLAYERadevice contains one PMD inter-

face. This PMD Interface should be used for all PMD imple-

mentations that do not require an external scrambler/

descrambler function, clock recovery function, or clock

generation function, such as a Fiber Optic or Shielded

Twisted Pair (SDDI) PMDs.

The DP83256-AP and DP83257 PLAYERadevices contain

two PMD interfaces. The PMD Interface should be used for

all PMD implementations that do not require an external

scrambler/descrambler function, clock recovery function,

or clock generation function, such as a Fiber Optic or

Shielded Twisted Pair (SDDI) PMDs. The second, Alternate

PMD Interface can be used to support Unshielded Twisted

Pair (UTP) PMDs that require external scrambling, and al-

lows implementation with no external clock recovery or

clock generation functions required. See

Figure 3-21.

PLAYERaTO PMD CONNECTIONS

The following figures illustrate how the PLAYERadevice

can be connected to various types of PMDs.

Figure 3-20

shows how the DP83256, DP83256-AP, or

DP83257 PLAYERadevice is connected to a Fiber Optic

or Shielded Twisted Pair (SDDI) PMD using the Primary

PMD Interface.

Figure 3-21

shows how the DP83256-AP or DP83257

PLAYERadevice is connected to an Unshielded Twisted

Pair (UTP) PMD using the Alternate PMD Interface.

TL/F/11708– 47

FIGURE 3-20. Fiber Optic or STP PMD Connection

TL/F/11708– 48

FIGURE 3-21. UTP PMD Connections

3.0 Functional Description (Continued)

INTERFACE ACTIVATION

The Primary PMD Interface is always enabled.

The Alternate PMD Interface is enabled by programming a

PLAYERaregister bit. To enable the interface, writea1to

the APMDEN bit in the APMDREG register. The interface is

off by default and should be left that way unless it is being

used.

It will also probably be necessary to enable the Transmit

Clocks when using the Alternate PMD Interface. The Trans-

mit Clocks (TXC) are enabled by writing a 1 to the TXCE bit

in the CGMREG register. The transmit clocks are disabled

by default and should be left that way unless it is being

used.

Note that when the Alternate PMD Interface is active, the

Primary PMD Interface can not be used without the Alter-

nate PMD Interface connections. Also note that the Long

Internal Loopback (LILB) can not be used when the Alter-

nate PMD Interface is activated.

4.0 Modes of Operation

The PLAYERadevice can operate in 4 basic modes: RUN,

STOP, LOOPBACK, and CASCADE.

4.1 RUN MODE

RUN is the normal mode of operation.

In this mode, the PLAYERadevice is configured to be con-

nected to the media via the PMD transmitter and PMD re-

ceiver at the PMD Interface. It is also connected to any

other PLAYERadevice(s) and/or MACSI device(s) via the

Port A and Port B Interfaces.

While operating in the RUN mode, the PLAYERadevice

receives and transmits Line States (Quiet, Halt, Master, Idle)

and frames (Active LIne State).

4.2 STOP MODE

The PLAYERadevice operates in the STOP mode while it

is being initialized or configured.

The PLAYERadevice is also reset to the STOP mode au-

tomatically when the ERST pin is set to ground.

When in STOP mode, the PLAYERadevice performs the

following functions:

#Resets the Repeat Filter.

#Resets the Smoother.

#Resets the Receiver Block Line State Counters.

#Resets the Clock Recovery Module

#Flushes the Elasticity Buffer.

#Forces Line State Unknown in the Receiver Block.

#Outputs PHY Invalid condition symbol pairs through the

PHY Data Indicate pins (AIP, AIC, AIDk7:0l, BIP, BIC,

BIDk7:0l), when port is enabled.

#Outputs Quiet symbol pairs through the PMD Data Re-

quest pins (PMRDg).

4.3 LOOPBACK MODE

The PLAYERadevice provides 3 types of loopback tests:

Configuration Switch Loopback, Short Internal Loopback,

and Long Internal Loopback. These Loopback modes can

be used to test different portions of the device.

Configuration Switch Loopback

The Configuration Switch Loopback can be used to test the

data paths of the MACSI device(s) that are connected to the

PLAYERadevice before transmitting and receiving data

through the network.

In the Configuration Switch Loopback mode, the PLAYERa

device Configuration Register (CR) can be programmed to

perform the following functions:

#Select Port A PHY Request Data, Port B PHY Request

Data, or PHY Invalid to connect to Port A PHY Indicate

Data via the AÐIND Mux.

#Select Port A PHY Request Data, Port B PHY Request

Data, or PHY Invalid to connect to Port B PHY Indicate

Data via the BÐIND Mux.

#Connect data from the Receiver Block to the Transmitter

Block via the TransmitterÐMux. (The PLAYERadevice

is repeating incoming data from the media in the Configu-

ration Switch Loopback mode.)

See

Figure 4-1

and

Figure 4-2.

TL/F/11708– 23

FIGURE 4-1. Configuration Switch Loopback

for DP83257

TL/F/11708– 24

FIGURE 4-2. Configuration Switch Loopback

for DP83256 and DP 83256-AP

4.0 Modes of Operation (Continued)

Short Internal Loopback

The Short Internal Loopback mode can be used to test the

functionality of the PLAYERadevice, not including the

Clock Recovery function, and to test the data paths be-

tween the PLAYERadevice and MACSI devices before

ring insertion.

When in the Short Internal Loopback mode, the PLAYERa

device performs the following functions:

#Directs the output data of the Transmitter Block to the

input of the Receiver Block through an internal path.

#Ignores the PMD Data Indicate pins (PMIDg),

#Outputs Quiet symbols through the PMD Data Request

pins (PMRDg).

The level of the Quiet symbols transmitted through the

PMRDgpins during loopback is automatically set to the

transmitter off level.

If both Short Internal Loopback and Long Internal Loopback

modes are selected, Long Internal Loopback mode will

have priority over Short Internal Loopback mode. This is the

longest loopback path within the PLAYERadevice.

See

Figure 4-3

, Short Internal Loopback.

TL/F/11708– 25

FIGURE 4-3. Short Internal Loopback

4.0 Modes of Operation (Continued)

Long Internal Loopback

The Long Internal Loopback mode implements the longest

loopback path that is completely within the PLAYERade-

vice.

The Long Internal Loopback mode can be used to test the

functionality of the PLAYERadevice, including the Clock

Recovery function, and to test the data paths between the

PLAYERadevice and MACSI devices before ring insertion.

When in the Long Internal Loopback mode, the PLAYERa

device performs the following functions:

#Directs the output data of the Transmitter Block to the

input of the Clock Recovery Module through an internal

path.

#Ignores the PMD Data Indicate pins (PMIDg),

#Outputs Quiet symbols through the PMD Data Request

pins (PMRDg).

The level of the Quiet symbols transmitted through the

PMRDgpins during loopback is automatically set to the

transmitter off level.

If both Short Internal Loopback and Long Internal Loopback

modes are selected, Long Internal Loopback mode will

have priority over Short Internal Loopback mode. This is the

longest loopback path within the PLAYERadevice.

Note that the LILB path is disconnected and should not be

used when the Alternate PMD Interface is active.

See

Figure 4-4

, Long Internal Loopback.

TL/F/11708– 26

FIGURE 4-4. Long Internal Loopback

4.0 Modes of Operation (Continued)

4.4 DEVICE RESET

The revision B PLAYERadevice has five different levels of

device ResetÐPower Up Reset, Hardware Reset, Player

Reset, Reference Select Reset, and Stop Mode. The Re-

sets can be used to return the whole device or a portion of

the device to its default configuration.

Power Up Reset begins automatically when power is first

applied to the PLAYERadevice and reaches a certain volt-

age level. Power Up Reset affects all of the modules in the

PLAYERadevice, specifically the Clock Generation Mod-

ule (CGM), Clock Recovery Module (CRM), and the Player

Module, returning each module to its default configuration.

This reset begins by waiting for the crystal to stabilize, then

the CGM PLL proceeds to lock to the crystal and the rest of

the PLAYERadevice is reset. This reset takes the longest

amount of time at approximately 10 ms from the time the

PLAYERadevice’s power supply reaches 4.4V. Even

though the Power Up Reset is usually effective, due to the

variation in the start-up conditions of a systems power sup-

ply, the Power Up Reset trigger can not be guaranteed to

operate correctly. Therefore, a Hardware Reset should al-

ways be performed on the PLAYERaafter waiting a mini-

mum of 10 ms for the Power Up Reset to complete its reset

attempt.

Hardware Reset occurs at the rising edge of PLAYERa

device’s ERST pin. Hardware Reset affects all of the mod-

ules in the PLAYERadevice, specifically the CGM, CRM

and the Player Module, returning each module to its default

configuration. During Hardware Reset it is not necessary to

force the Clock Generation Module to wait for the crystal to

settle again at this time because it has settled in the time

since the initial reset at power up. This reset takes the sec-

ond longest amount of time at approximately 1 ms from the

rising edge of ERST.

Player Reset is activated by writinga1tothePHYRST bit in

Mode Register 2. Player Reset only affects the Player Mod-

ule. This reset is the shortest and only takes about 3 ms

from the completion of the register write. The device should

not be accessed by the Control Bus during this reset.

Reference Select Reset occurs when the PLAYERade-

vice’s REFÐSEL pin is switched from using the REFÐIN

input to using a crystal with the XTALÐIN and XTALÐOUT

pins. This is the same as a Power Up Reset and is done

because the crystal is going from a dead stop to an active

state when REFÐSEL is switched. This reset, like the Pow-

er Up Reset, takes about 10 ms from the falling edge of

REFÐSEL.

Stop Mode is activated by writinga0totheRUNbitinthe

Mode Register. Stop Mode is a selective reset that resets

the Clock Recovery Module and portions of the Player Mod-

ule.

Changes from Revision A to Revision B:

The previous descriptions describe the reset logic in the

revision B PLAYERadevice. Two changes were made to

the original revision A PLAYERadevice reset logic.

First, the Hardware Reset was shortened by eliminating the

requirement of having to wait for the crystal to settle before

letting the Clock Generation Module try to lock to the crys-

tal. This behavior is correct because the PLAYERadevice

has already waited for the crystal to settle once during the

Power Up Reset. The revision A PLAYERafollows a Power

Up Reset cycle when Hardware Reset is activated.

Second, a full Power Up Reset is now done when the clock

reference is switched to the crystal. This is necessary to

allow the crystal time to start up when it is switched to from

the REFÐIN input. This reset is not performed on the revi-

sion A PLAYERa.

Recommendations:

The following are some recommendations for using the re-

set mechanisms of the PLAYERamost effectively:

1. Always wait a minimum of 10 ms after power-up before

doing anything to the PLAYERadevice. 10 ms is a mini-

mum, it may be desirable to wait longer if the system

power supply or clock reference has not stabilized by this

time.

2. Always use the Hardware Reset to reset the PLAYERa

device after Power Up. This should be done after the

initial Power Up waiting period of at least 10 ms.

4.0 Modes of Operation (Continued)

4.5 CASCADE MODE

The PLAYERadevice can operate in the Cascade (paral-

lel) mode

(Figure 4-5)

which is used in high bandwidth,

point-to-point data transfer applications. This is a non-FDDI

mode of operation. This is only available on the DP83257

device.

Concepts

In the Cascade mode, multiple PLAYERadevices are con-

nected together to provide data transfer at multiples of the

FDDI data rate. Two cascaded PLAYERadevices provide

a data rate twice the FDDI data rate; three cascaded

PLAYERadevices provide a data rate three times the FDDI

data rate, etc.

Multiple data streams are transmitted in parallel over each

pair of cascaded PLAYERadevices. All data streams start

simultaneously and begin with the JK symbol pair on each

PLAYERadevice.

Data is synchronized at the receiver of each PLAYERade-

vice by the JK symbol pair. Upon receiving a JK symbol pair,

a PLAYERadevice asserts the Cascade Ready signal to

indicate the beginning of data reception.

The Cascade Ready signals of all PLAYERadevices are

open drain ANDed together to create the Cascade Start

signal. The Cascade Start signal is used as the input to

indicate that all PLAYERadevices have received the JK

symbol pair. Data is now being received at every PLAYERa

device and can be transferred from the cascaded

PLAYERadevices to the host system.

See

Figure 4-6

for more information.

Operating Rules

When the PLAYERadevice is operating in Cascade mode,

the following rules apply:

1. Data integrity can be guaranteed if the worst case PMD

transmission skew between parallel media is less than

40 ns. For example, this amounts to about 785 meters of

fiber optic cable, assuming a 1% worst case variance.

2. Even though this is a non-FDDI application, the general

rules for FDDI frames must be obeyed.

#Data frames must be a minimum of three bytes long

(including the JK symbol pair). Smaller frames will

cause Elasticity Buffer errors.

#Data frames must have a maximum size of 4500 bytes,

with a JK starting delimiter and a T or R or S ending

delimiter.

3. Due to the different clock rates, the JK symbol pair may

arrive at different times at each PLAYERadevice. The

total skew between the fastest and slowest cascaded

PLAYERadevices receiving the JK starting delimiter

must not exceed 80 ns.

4. The first PLAYERadevice to receive a JK symbol pair

will present it to the host system and release the Cas-

cade Ready signal. The PLAYERadevice will present

one more JK as it waits for the other PLAYERadevices

to recognize their JK. The maximum number of consecu-

tive JKs that can be presented to the host is 2.

5. The Cascade Start signal is set to 1 when all the cascad-

ed PLAYERadevices release their Cascade Ready sig-

nals.

6. Bit 4 (CSE) of the Receive Condition Register B (RCRB)

is set to 1 if the Cascade Start signal (CS) is not set

before the second falling edge of clock signal LBC from

when Cascade Ready (CR) was released. CS has to be

set approximately within 80 ns of CR release. This condi-

tion signifies that not all cascaded PLAYERadevices

have received their respective JK symbol pair with the

allowed skew range.

7. PLAYERadevices may not report a Cascaded Synchro-

nization Error if the JK symbols are corrupted in the point-

to-point links.

8. To guarantee integrity of the interframe information, the

user must put at least 8 Idle symbol pairs between

frames. The PLAYERadevice will function properly with

only 4 Idle symbol pairs, however the interframe symbols

may be corrupted with random non-JK symbols.

The MACSI device could be used to provide the required

framing and optional FCS support.

4.0 Modes of Operation (Continued)

TL/F/11708– 27

FIGURE 4-5. Parallel Transmission

TL/F/11708– 28

FIGURE 4-6. Cascade Mode of Operation

5.0 Registers

The PLAYERadevice can be initialized, configured, and monitored using 64 8-bit registers. These registers are accessible

through the Control Bus Interface.

The following tables summarize each register’s attributes.

Note: RESERVED Registers may be read at any time, although the values read are not specified. The results of RESERVED Register writes are not specified, and

may have adverse implications. The user should not write to RESERVED Register locations.

TABLE 5-1. Register Summary

Address

Symbol Register Name Access Rules

Read Write

00h MR Mode Register Always Always

01h CR Configuration Register Always Conditional

02h ICR Interrupt Condition Register Always Conditional

03h ICMR Interrupt Condition Mask Register Always Always

04h CTSR Current Transmit State Register Always Conditional

05h IJTR Injection Threshold Register Always Always

06h ISRA Injection Symbol Register A Always Always

07h ISRB Injection Symbol Register B Always Always

08h CRSR Current Receive State Register Always Write Reject

09h RCRA Receive Condition Register A Always Conditional

0Ah RCRB Receive Condition Register B Always Conditional

0Bh RCMRA Receive Condition Mask Register A Always Always

0Ch RCMRB Receive Condition Mask Register B Always Always

0Dh NTR Noise Threshold Register Always Always

0Eh NPTR Noise Prescale Threshold Register Always Always

0Fh CNCR Current Noise Count Register Always Write Reject

10h CNPCR Current Noise Prescale Count Register Always Write Reject

11h STR State Threshold Register Always Always

12h SPTR State Prescale Threshold Register Always Always

13h CSCR Current State Count Register Always Write Reject

14h CSPCR Current State Prescale Count Register Always Write Reject

15h LETR Link Error Threshold Register Always Always

16h CLECR Current Link Error Count Register Always Write Reject

17h UDR User Definable Register Always Always

18h IDR Device ID Register Always Write Reject

19h CIJCR Current Injection Count Register Always Write Reject

1Ah ICCR Interrupt Condition Comparison Register Always Always

1Bh CTSCR Current Transmit State Comparison Register Always Always

1Ch RCCRA Receive Condition Comparison Register A Always Always

5.0 Registers (Continued)

TABLE 5-1. Register Summary (Continued)

Address

Symbol Register Name Access Rules

Read Write

1Dh RCCRB Receive Condition Comparison Register B Always Always

1Eh MODE2 Mode Register 2 Always Conditional

1Fh CMTCCR CMT Condition Comparison Register Always Always

20h CMTCR CMT Condition Register Always Conditional

21h CMTMR CMT Condition Mask Register Always Always

22h RR22 Reserved Register 22 Always DO NOT WRITE

23h RR23 Reserved Register 23 Always DO NOT WRITE

24h STTR Scrub Timer Threshold Register Always Always

25h STVR Scrub Timer Value Register Always Write Reject

26h TDR Trigger Definition Register Always Always

27h TTCR Trigger Transition Configuration Register Always Always

28h RR28 Reserved Register 28 Always DO NOT WRITE

29h RR29 Reserved Register 29 Always DO NOT WRITE

2Ah RR2A Reserved Register 2A Always DO NOT WRITE

2Bh RR2B Reserved Register 2B Always DO NOT WRITE

2Ch RR2C Reserved Register 2C Always DO NOT WRITE

2Dh RR2D Reserved Register 2D Always DO NOT WRITE

2Eh RR2E Reserved Register 2E Always DO NOT WRITE

2Fh RR2F Reserved Register 2F Always DO NOT WRITE

30h RR30 Reserved Register 30 Always DO NOT WRITE

31h RR31 Reserved Register 31 Always DO NOT WRITE

32h RR32 Reserved Register 32 Always DO NOT WRITE

33h RR33 Reserved Register 33 Always DO NOT WRITE

34h RR34 Reserved Register 34 Always DO NOT WRITE

35h RR35 Reserved Register 35 Always DO NOT WRITE

36h RR36 Reserved Register 36 Always DO NOT WRITE

37h RR37 Reserved Register 37 Always DO NOT WRITE

38h RR38 Reserved Register 38 Always DO NOT WRITE

39h RR39 Reserved Register 39 Always DO NOT WRITE

3Ah RR3A Reserved Register 3A Always DO NOT WRITE

3Bh CGMREG Clock Generation Module Register Always Always

3Ch APMDREG Alternate PMD Register Always Always

3Dh GAINREG Gain Register Always Always

3Eh RR3E Reserved Register 3E Always DO NOT WRITE

3Fh RR3F Reserved Register 3F Always DO NOT WRITE

5.0 Registers (Continued)

TABLE 5-2. Register Bit Summary

Address

Symbol

Bit Symbols

D7 D6 D5 D4 D3 D2 D1 D0

00h MR RNRZ TNRZ TE TQL CM EXLB ILB RUN

01h CR BIE AIE TRS1 TRS0 BIS1 BIS0 AIS1 AIS0

02h ICR UDI RCB RCA LEMT CWI CCR CPE DPE

03h ICMR UDIM RCBM RCAM LEMTM CWIM CCRM CPEM DPEM

04h CTSR RES PRDPE SE IC1 IC0 TM2 TM1 TM0

05h IJTR IJT7 IJT6 IIJ5 IJT4 IJT3 IJT2 IJT1 IJT0

06h ISRA RES RES RES IJS4 IJS3 IJS2 IJS1 IJS0

07h ISRB RES RES RES IJS9 IJS8 IJS7 IJS6 IJS5

08h CRSR RES RES RES RES LSU LS2 LS1 LS0

09h RCRA LSUPI LSC NT NLS MLS HLS QLS NSD

0Ah RCRB RES SILS EBOU CSE LSUPV ALS ST ILS

0Bh RCMRA LSUPIM LSCM NTM NLSM MLSM HLSM QLSM NSDM

0Ch RCMRB RES SILSM EBOUM CSEM LSUPVM ALSM STM ILSM

0Dh NTR RES NT6 NT5 NT4 NT3 NT2 NT1 NT0

0Eh NPTR NPT7 NPT6 NPT5 NPT4 NPT3 NPT2 NPT1 NPT0

0Fh CNCR NCLSCD CNC6 CNC5 CNC4 CNC3 CNC2 CNC1 CNC0

10h CNPCR CNPC7 CNPC6 CNPC5 CNPC4 CNPC3 CNPC2 CNPC1 CNPC0

11h STR RES ST6 ST5 ST4 ST3 ST2 ST1 ST0

12h SPTR SPT7 SPT6 SPT5 SPT4 SPT3 SPT2 SPT1 SPT0

13h CSCR SCLSCD CSC6 CSC5 CSC4 CSC3 CSC2 CSC1 CSC0

14h CSPCR CSPC7 CSPC6 CSPC5 CSPC4 CSPC3 CSPC2 CSPC1 CSPC0

15h LETR LET7 LET6 LET5 LET4 LET3 LET2 LET1 LET0

16h CLECR LEC7 LEC6 LEC5 LEC4 LEC3 LEC2 LEC1 LEC0

17h UDR RES RES RES RES EB1 EB0 SB1 SB0

18h IDR DID7 DID6 DID5 DID4 DID3 DID2 DID1 DID0

19h CIJCR IJC7 IJC6 IJC5 IJC4 IJC3 IJC2 IJC1 IJC0

1Ah ICCR UDIC RCBC RCAC LEMTC CWIC CCRC CPEC DPEC

1Bh CTSCR RESC PRDPEC SEC IC1C IC0C TM2C TM1C TM0C

1Ch RCCRA LSUPIC LSCC NTC NLSC MLSC HLSC QLSC NSDC

1Dh RCCRB RESC SILSC EBOUC CSEC LSUPVC ALSC STC ILSC

1Eh MODE2 ESTC RES CLKSEL RES RES RES CBPE PHYRST

1Fh CMTCCR TCOC STEC RES RES RES RES RES RES

20h CMTCR TCO STE RES RES RES RES RES RES

21h CMTMR TCOM STEM RES RES RES RES RES RES

22h RR22 RES RES RES RES RES RES RES RES

5.0 Registers (Continued)

TABLE 5-2. Register Bit Summary (Continued)

Address

Symbol

Bit Symbols

D7 D6 D5 D4 D3 D2 D1 D0

23h RR23 RES RES RES RES RES RES RES RES

24h STTR STT7 STT6 STT5 STT4 STT3 STT2 STT1 STT0

25h STVR STV7 STV6 STV5 STV4 STV3 STV2 STV1 STV0

26h TDR TONT TOQLS TOHLS TOMLS TOSILS TTM2 TTM1 TTM0

27h TTCR BIE AIE TRS1 TRS0 BIS1 BIS0 AIS1 AIS0

28h RR28 RES RES RES RES RES RES RES RES

29h RR29 RES RES RES RES RES RES RES RES

2Ah RR2A RES RES RES RES RES RES RES RES

2Bh RR2B RES RES RES RES RES RES RES RES

2Ch RR2C RES RES RES RES RES RES RES RES

2Dh RR2D RES RES RES RES RES RES RES RES

2Eh RR2E RES RES RES RES RES RES RES RES

2Fh RR2F RES RES RES RES RES RES RES RES

30h RR30 RES RES RES RES RES RES RES RES

31h RR31 RES RES RES RES RES RES RES RES

32h RR32 RES RES RES RES RES RES RES RES

33h RR33 RES RES RES RES RES RES RES RES

34h RR34 RES RES RES RES RES RES RES RES

35h RR35 RES RES RES RES RES RES RES RES

36h RR36 RES RES RES RES RES RES RES RES

37h RR37 RES RES RES RES RES RES RES RES

38h RR38 RES RES RES RES RES RES RES RES

39h RR39 RES RES RES RES RES RES RES RES

3Ah RR3A RES RES RES RES RES RES RES RES

3Bh CGMREG RES RES FLTREN RES TXCE RES RES RES

3Ch APMDREG RES RES RES RES APMDEN RES RES RES

3Dh GAINREG FILT2 FILT1 FILT0 RES RES RES RES RES

3Eh RR3E RES RES RES RES RES RES RES RES

3Fh RR3F RES RES RES RES RES RES RES RES

5.0 Registers (Continued)

TABLE 5-3. Register Reset Value Summary

Address

Symbol

Reset Contents

MSB-LSB Comments

00h MR 00 h

01h CR 00 h

02h ICR X001 0000 B depends on sense pins

03h ICMR 00 h

04h CTSR A2 h

05h IJTR 00 h

06h ISRA 00 h

07h ISRB 00 h

08h CRSR 0A h

09h RCRA 20 h

0Ah RCRB 00X0 0010 B depends on EB state

0Bh RCMRA 00 h

0Ch RCMRB 00 h

0Dh NTR 00 h

0Eh NPTR 00 h

0Fh CNCR 00 h

10h CNPCR 00 h

11h STR 00 h

12h SPTR 00 h

13h CSCR 00 h

14h CSPCR 00 h

15h LETR 00 h

16h CLECR 00 h

17h UDR 000X 00XX B depends on sense pins

18h IDR XX h depends on chip version

19h CIJCR 00 h

1Ah ICCR 00 h same as reg 02 h if reg 02 h is read first

1Bh CTSCR 00 h same as reg 04 h if reg 04 h is read first

1Ch RCCRA 00 h same as reg 09 h if reg 09 h is read first

1Dh RCCRB 00 h same as reg 0A h if reg 0A h is read first

5.0 Registers (Continued)

TABLE 5-3. Register Reset Value Summary (Continued)

Address

Symbol

Reset Contents

MSB-LSB Comments

1Eh MODE2 00 h

1Fh CMTCCR 00 h

20h CMTCR 00 h

21h CMTMR 00 h

22h RR22 XX h

23h RR23 XX h

24h STTR 00 h

25h STVR 00 h

26h TDR 00 h

27h TTCR 00 h

28h RR28 XX h

29h RR29 XX h

2Ah RR2A XX h

2Bh RR2B XX h

2Ch RR2C XX h

2Dh RR2D XX h

2Eh RR2E XX h

2Fh RR2F XX h

30h RR30 XX h

31h RR31 XX h

32h RR32 XX h

33h RR33 XX h

34h RR34 XX h

35h RR35 XX h

36h RR36 XX h

37h RR37 XX h

38h RR38 XX h

39h RR39 XX h

3Ah RR3A XX h

3Bh CGMREG 05 h

3Ch APMDREG 00 h

3Dh GAINREG 00 h

3Eh RR3E XX h

3Fh RR3F XX h

5.0 Registers (Continued)

5.1 MODE REGISTER (MR)

The Mode Register is used to initialize and configure the PLAYERadevice.

ACCESS RULES

ADDRESS READ WRITE

00h Always Always

D7 D6 D5 D4 D3 D2 D1 D0

RNRZ TNRZ TE TQL CM LILB SILB RUN

Bit Symbol Description

D0 RUN RUN/ESTOP:

0: Enables the STOP mode. Refer to section 4.2, STOP MODE, for more information.

1: Normal operation (i.e. RUN mode).

Note: The RUN bit is automatically set to 0 when the ERST pin is asserted (i.e. set to ground).

D1 SILB SHORT INTERNAL LOOPBACK:

0: Disables Internal Loopback mode (i.e. normal operation).

1: Enables Internal Loopback mode.

Refer to section 4.3, LOOPBACK MODE, for more information.

D2 LILB LONG INTERNAL LOOPBACK:

0: Disables Long Internal Loopback mode (i.e. normal operation).

1: Enables Long Internal Loopback mode.

Note: Long Internal Loopback should not be used when the Alternate PMD Interface is enabled.

Refer to section 4.3, LOOPBACK MODE, for more information.

D3 CM CASCADE MODE:

0: Disables synchronization of cascaded PLAYERadevices.

1: Enables the synchronization of cascaded PLAYERadevices.

Refer to section 4.4, CASCADE MODE, for more information.

Note: Cascade Mode is only available on the DP83257 device. The other devices do not have the required CS and CR pins. Do not set this bit for

any device but the DP83257.

D4 TQL TRANSMIT QUIET LEVEL: This bit is used to program the transmission level of the Quiet symbols during Off

Transmit mode (OTM) only.

0: Low (PMD OFF) level Quiet symbols are transmitted through the PMD Data Request pins (i.e. PMRD aelow,

PMRD behigh).

1: High (PMD ON) level Quiet symbols are transmitted through the PMD Data Request pins (i.e. PMRD aehigh,

PMRD below).

D5 TE TRANSMIT ENABLE: The TE bit controls the action of the PMD transmitter Enable (TXE) pin. When TE is 0, the

TXE output disables the PMD transmitter; when TE is 1, the PMD transmitter is disabled during the Off Transmit

Mode (OTM) and enabled otherwise. The On and Off level of the TXE is depended on the PMD transmitter Enable

Level (TEL) pin to the PLAYERadevice. The following rules summaries the output of TXE.

1. If TEe0, then TXEeOff

2. If TEe1 and OTM, then TXEeOff

3. If TEe1 and not OTM, then TXEeOn.

D6 TNRZ TRANSMIT NRZ DATA:

0: Transmits data in Non-Return-To-Zero-Invert-On-Ones (NRZI) format (normal format).

1: Transmits data in Non-Return-To-Zero format (NRZ).

D7 RNRZ RECEIVE NRZ DATA:

0: Receives data in Non-Return-To-Zero-Invert-On-Ones format (NRZI) (normal format).

1: Receives data in Non-Return-To-Zero format (NRZ).

5.0 Registers (Continued)

5.2 CONFIGURATION REGISTER (CR)

The Configuration Register controls the Configuration Switch Block and enables/disables both the A and B ports. The CR can

be used to create a number of Configuration Loopback paths.

The CR is conditionally writable because the TTCR can be writing a new value into the register if this feature is enabled.

Note that the AÐRequest and BÐIndicate port are offered only on the DP83257, and not in the DP83256. For further informa-

tion, refer to section 3.4, CONFIGURATION SWITCH.

ACCESS RULES

ADDRESS READ WRITE

01h Always Conditional

D7 D6 D5 D4 D3 D2 D1 D0

BIE AIE TRS1 TRS0 BIS1 BIS0 AIS1 AIS0

Bit Symbol Description

D0, D1 AIS0, AIS1 AÐINDICATE SELECTOR k0, 1l:The AÐIndicate Selector k0, 1lbits selects one of the four

Configuration Switch data buses for the AÐIndicate output port (AIP, AIC, AIDk7:0l).

AIS1 AIS0

0 0 PHY Invalid Bus

0 1 Receiver Bus

10A

Request Bus

11B

Request Bus

D2, D3 BIS0, BIS1 BÐINDICATE SELECTOR k0, 1l:The BÐIndicate Selector k0, 1lbits selects one of the four

Configuration Switch data buses for the BÐIndicate output port (BIP, BIC, BIDk7:0l)

BIS1 BIS0

0 0 PHY Invalid Bus

0 1 Receiver Bus

10A

Request Bus

11B

Request Bus

Note: Even though this bit can be set and/or cleared in the DP83256, it will not affect any I/Os since the DP83256 does not offer a

BÐIndicate port.

D4, D5 TRS0, TRS1 TRANSMIT REQUEST SELECTOR k0, 1l:The Transmit Request Selector k0, 1lbits select one of

the four Configuration Switch data buses for the input to the Transmitter Block.

TRS1 TRS0

0 0 PHY Invalid Bus

0 1 Receiver Bus

10A

Request Bus

11B

Request Bus

Note: If the PLAYERadevice is in Active Transmit Mode (i.e. the Transmit Mode bits (TMk2:0l) of the Current Transmit State

Register (CTSR) are set to 00) and the PHY Invalid Bus is selected, then the PLAYERadevice will transmit a maximum of four

Halt symbol pairs and then continuous Idle symbols due to the Repeat Filter when in the Repeat state.

D6 AIE AÐINDICATE ENABLE:

0: Disables the AÐIndicate output port. The AÐIndicate port pins will be tri-stated when the port is

disabled.

1: Enables the AÐIndicate output port (AIP, AIC, AIDk7:0l).

D7 BIE BÐINDICATE ENABLE:

0: Disables the BÐIndicate output port. The BÐIndicate port pins will be tri-stated when the port is

disabled.

1: Enables the BÐIndicate output port (BIP, BIC, BIDk7:0l).

Note: Even though this bit can be set and/or cleared in the DP83256, it will not affect any I/Os since the DP83256 does not offer a

BÐIndicate port.

5.0 Registers (Continued)

5.3 INTERRUPT CONDITION REGISTER (ICR)

The Interrupt Condition Register records the occurrence of an internal error event, the detection of Line State, an unsuccessful

write by the Control Bus Interface, the expiration of an internal counter, or the assertion of one or more of the User Definable

Sense pins.

The Interrupt Condition Register will assert the Interrupt pin (EINT) when one or more bits within the register are set to 1 and

the corresponding mask bits in the Interrupt Condition Mask Register (ICMR) are also set to 1.

ACCESS RULES

ADDRESS READ WRITE

02h Always Conditional

D7 D6 D5 D4 D3 D2 D1 D0

UDI RCB RCA LEMT CWI CCR CPE DPE

Bit Symbol Description

D0 DPE PHYÐREQUESTÐDATA PARITY ERROR: This bit will be set to 1 when:

1. The PHY Request Data Parity Enable bit (PRDPE) of the Current Transmit State Register (CTSR) is set to 1 and

2. The Transmitter Block detects a parity error in the incoming PHY Request Data.

The source of the data can be from the PHY Invalid Bus, the Receive Bus, the AÐBus, or the BÐBus of the

Configuration Switch.

Note: Parity is only checked on data that goes into the transmitter block. This means that any data that is just routed through the configuration

switch without going into the transmit block is not checked.

D1 CPE Control Bus DATA PARITY ERROR: This bit will be set to 1 when the Control Bus Interface detects a parity error

in the incoming Control Bus Data (CBDk7:0l), CBP during a write cycle.

D2 CCR Control Bus WRITE COMMAND REJECT: This bit will be set to 1 when an attempt to write into one of the

following read-only registers is made:

Current Receive State Register (Register 08, CRSR)

Current Noise Count Register (Register 0F, CNCR)

Current Noise Prescale Count Register (Register 10, CNPCR)

Current State Count Register (Register 13, CSCR)

Current State Prescale Count Register (Register 14, CSPCR)

Current Link Error Count Register (Register 16, CLECR)

Device ID Register (Register 18, IDR)

Current Injection Count Register (Register 19, CIJCR)

Scrub Timer Value Register (Register 25, STVR)

5.0 Registers (Continued)

Bit Symbol Description

D3 CWI CONDITIONAL WRITE INHIBIT: Set to 1 when bits within mentioned registers do not match bits in the

corresponding compare register. This bit ensures that new (i.e. unread) data is not inadvertently cleared while old

data is being cleared through the Control Bus Interface.

This bit is set to 1 to indicate that a bit in a condition write register was not written because it had changed since

the previous read. The following registers are affected:

Interrupt Condition Register (Register 02, ICR)

Current Transmit State Register (Register 04, CTSR)

Receive Condition Register A (Register 09, RCRA)

Receive Condition Register B (Register 0A, RCRB)

CMT Condition Register (Register 20, CMTCR)

The previous registers are affected when they differ from the value of the corresponding bit in the following

registers respectively:

Interrupt Condition Compare Register (Register 1A, ICCR)

Current Transmit State Compare Register (Register 1B, CTSCR)

Receive Condition Compare Register A (Register 1C, RCCRA)

Receive Condition Compare Register B (Register 1D, RCCRB)

CMT Condition Compare Register (Register 1F, CMTCCR)

This bit must be cleared by software. Note that this differs from the MACSI, BMAC and BSI device bits of the same

name.

The Configuration Register (Register 01, CR) can not be written to during scrubbing.

D4 LEMT LINK ERROR MONITOR THRESHOLD: This bit is set to 1 when the internal 8-bit Link Error Monitor Counter

reaches zero. It will remain set and is cleared by software.

During the reset process (i.e. ERSTeGND), the Link Error Monitor Threshold bit is set to 1 because the Link

Error Monitor Counter is initialized to zero.

D5 RCA RECEIVE CONDITION A: This bit is set to 1 when:

1. One or more bits in the Receive Condition Register A (RCRA) is set to 1 and

2. The corresponding mask bits in the Receive Condition Mask Register A (RCMRA) are also set to 1.

In order to clear (i.e. set to 0) the Receive Condition A bit, the bits within the Receive Condition Register A that are

set to 1 must first be either cleared or masked.

D6 RCB RECEIVE CONDITION B: This bit is set to 1 when:

1. One or more bits in the Receive Condition Register B (RCRB) is set to 1 and

2. The corresponding mask bits in the Receive Condition Mask Register A (RCMRB) are also set to 1.

In order to clear (i.e. set to 0) the Receive Condition B bit, the bits within the Receive Condition Register B that are

set to 1 must first be either cleared or masked.

D7 UDI USER DEFINABLE INTERRUPT: This bit is set to 1 when one or any combination of the Sense Bits (SB0, SB1, or

SB2) in the User Definable Register (UDR) are set to 1.

In order to clear (i.e. set to 0) the User Definable Interrupt Bit, all Sense Bits must be set to 0.

5.0 Registers (Continued)

5.4 INTERRUPT CONDITION MASK REGISTER (ICMR)

The Interrupt Condition Mask Register allows the user to dynamically select which events will generate an interrupt.

The Interrupt pin will be asserted (i.e. EINT eGND) when one or more bits within the Interrupt Condition Register (ICR) are set

to 1 and the corresponding mask bits in this register are also set to 1.

This register is cleared (i.e. set to 0) and all interrupts are initially masked during the reset process.

ACCESS RULES

ADDRESS READ WRITE

03h Always Always

D7 D6 D5 D4 D3 D2 D1 D0

UDIM RCBM RCAM LEMTM CWIM CCRM CPEM DPEM

Bit Symbol Description

D0 DPEM PHYÐREQUESTÐDATA PARITY ERROR MASK: The mask bit for the PHYÐRequest Data Parity Error bit

(DPE) of the Interrupt Condition Register (ICR).

D1 CPEM Control Bus DATA PARITY ERROR MASK: The mask bit for the Control Bus Data Parity Error bit (CPE) of the

Interrupt Condition Register (ICR).

D2 CCRM Control Bus WRITE COMMAND REJECT MASK: The mask bit for the Control Bus Write Command Reject bit

(CCR) of the Interrupt Condition Register (ICR).

D3 CWIM CONDITIONAL WRITE INHIBIT MASK: The mask bit for the Conditional Write Inhibit bit (CWI) of the Interrupt

Condition Register (ICR).

D4 LEMTM LINK ERROR MONITOR THRESHOLD MASK: The mask bit for the Link Error Monitor Threshold bit (LEMT) of

the Interrupt Condition Register (ICR).

D5 RCAM RECEIVE CONDITION A MASK: The mask bit for the Receive Condition A bit (RCA) of the Interrupt Condition

D6 RCBM RECEIVE CONDITION B MASK: The mask bit for the Receive Condition B bit (RCB) of the Interrupt Condition

D7 UDIM USER DEFINABLE INTERRUPT MASK: The mask bit for the User Definable Interrupt bit (UDI) of the Interrupt

Condition Register (ICR).

5.0 Registers (Continued)

5.5 CURRENT TRANSMIT STATE REGISTER (CTSR)

The Current Transmit State Register can program the Transmitter Block to internally generate and transmit Idle, Master, Halt,

Quiet, or user programmable symbol pairs, in addition to the normal transmission of incoming PHY Request data. The Smoother

and PHY Request Data Parity are also enabled and disabled through this register.

When the Trigger Definition register (TDR) is used, the CTSR can automatically be set to a preprogrammed line state when a

trigger condition occurs. This capability can be used to implement both PCÐReact and CFÐReact.

The Transmit Modes have priority over the Repeat Filter and Smoother outputs. The Injection Symbols have priority over the

Transmit Modes.

During the reset process (i.e. ERSTeGND) the Transmit Mode is set to Off (TMk2:0le010), the Smoother is enabled (i.e. SE

is set to 1), and the Reserved bit (b7) is set to 1. All other bits of this register are cleared (i.e. set to 0) during the reset process.

When the TDR register is used to respond to trigger conditions the CTSR will be blocked when the TDR register transmit mode

is copied into the CTSR. The Write Reject bit of the ICR will be set if any writes are attempted at this time.

Note: This register has no effect while the device is in Stop Mode.

ACCESS RULES

ADDRESS READ WRITE

04h Always Conditional

D7 D6 D5 D4 D3 D2 D1 D0

RES PRDPE SE IC1 IC0 TM2 TM1 TM0

Bit Symbol Description

D0, D1, TM0, TM1, Transmit Mode k0, 1, 2l:These bits select one of the 6 transmission modes for the PMD Request Data

output port (TXDg).

D2 TM2

TM2 TM1 TM0

000Active Transmit Mode (ATM): Normal transmission of incoming PHY Request data.

001Idle Transmit Mode (ITM): Transmission of Idle symbol pairs (11111 11111).

010Off Transmit Mode (OTM): Transmission of Quiet symbol pairs (00000 00000) and

deassertion of the PMD transmitter Enable pin (TXE).

Note: This is the default transmit mode after reset.

011Reserved: Reserved for future use. Users are discouraged from using this transmit

mode. If selected, however, the transmitter will generate Quiet symbol pairs (00000

00000).

100Master Transmit Mode (MTM): Transmission of Halt and Quiet symbol pairs (00100

00000).

101Halt Transmit Mode (HTM): Transmission of Halt symbol pairs (00100 00100).

110Quiet Transmit Mode (QTM): Transmission of Quiet symbol pairs (00000 00000).

111Reserved: Reserved for future use. Users are discouraged from using this transmit

mode. If selected, however, the transmitter will generate Quiet symbol pairs

(00000 00000).

5.0 Registers (Continued)

Bit Symbol Description

D3, D4 IC0, IC1 Injection Control k0, 1l:These bits select one of the 4 injection modes. The injection modes have priority

over data from the Smoother, Repeat Filter, Encoder, and Transmit Modes.

IC0 is the only bit of the register that is automatically cleared by the PLAYERadevice after the One Shot

Injection is executed. The automatic clear of IC0 during the One Shot mode can be interpreted as a

acknowledgment that the One Shot has been completed.

IC1 IC0

00No Injection: The normal transmission of incoming PHY Request data (i.e. symbols are not

injected).

01One Shot: In one shot mode, the contents of Injection Symbol Register A (ISRA) and Injection

Symbol Register B (ISRB) are injected n symbol pairs after a JK, where n is the programmed

value of the Injection Count Register (IJCR). If IJCR is set to 0, the JK symbol pair is replaced by

ISRA and ISRB. Once the One Shot is executed, the PLAYERadevice automatically sets IC0 to

0, thereby returning to normal transmission of data.

10Periodic: In Periodic mode, the contents of Injection Symbol Register A (ISRA) and Injection

Symbol Register B (ISRB) are injected every n-th symbol pair, where n is the programmed value

of the Injection Count Register (IJCR). If IJCR is set to 0, all data symbols are replaced with ISRA

and ISRB.

Note: The inserted symbol is not automatically aligned to a JK boundary.

11Continuous: In Continuous mode, all data symbols are replaced with the contents of Injection

Symbol Register A (ISRA) and Injection Symbol Register B (ISRB).

D5 SE SMOOTHER ENABLE:

0: Disables the Smoother.

1: Enables the Smoother.

When enabled, the Smoother can redistribute Idle symbol pairs which were added or deleted by the

local or upstream receivers.

Note: Once the counter has started, it will continue to count irrespective of the incoming symbols with the exception of a JK symbol pair.

D6 PRDPE PHYÐREQUEST DATA PARITY ENABLE:

0: Disables PHYÐRequest Data parity.

1: Enables PHYÐRequest Data parity.

D7 RES RESERVED: Reserved for future use.

Note: Users are discouraged from using this bit. The reserved bit is set to 1 during the reset process. It may be set or cleared without any

effects to the functionality of the PLAYERadevice.

5.0 Registers (Continued)

5.6 INJECTION THRESHOLD REGISTER (IJTR)

The Injection Threshold Register, in conjunction with the Injection Control bits (ICk1:0l) in the Current Transmit State Register

(CTSR), set the frequency at which the contents of the Injection Symbol Register A (ISRA) and Injection Symbol Register B

(ISRB) are inserted into the data stream. It contains the start value for the Injection Counter.

The Injection Threshold Register value is loaded into the Injection Counter when the counter reaches zero or during every

Control Bus Interface write-cycle of this register.

The Injection Counter is an 8-bit down-counter which decrements every 80 ns. It’s current value is read for CIJCR.

The counter is active only during One Shot or Periodic Injection Modes (i.e. Injection Controlk1:0lbits (ICk1:0l)ofthe

Current Transmit State Register (CTSR) are set to either 01 or 10). The Transmitter Block will replace a data symbol pair with

ISRA and ISRB when the counter reaches 0 and the Injection Mode is either One Shot or Periodic.

If the Injection Threshold Register is set to 0 during the One Shot mode, the JK will be replaced with ISRA and ISRB. If the

Injection Threshold Register is set to 0 during the Periodic mode, all data symbols are replaced with ISRA and ISRB.

The counter is initialized to 0 during the reset process (i.e. ERSTeGND).

For further information, see the INJECTION CONTROL LOGIC section.

ACCESS RULES

ADDRESS READ WRITE

05h Always Always

D7 D6 D5 D4 D3 D2 D1 D0

IJT7 IJT6 IJT5 IJT4 IJT3 IJT2 IJT1 IJT0

Bit Symbol Description

D0-D7 IJT0–IJT7 INJECTION THRESHOLD BITk0-7l:Start value for the Injection Counter.

IJT0 is the Least Significant Bit (LSB).

5.0 Registers (Continued)

5.7 INJECTION SYMBOL REGISTER A (ISRA)

The Injection Symbol Register A, along with Injection Symbol Register B, contains the programmable value (already in 5B code)

that can be inserted to replace the data symbol pairs.

In One Shot mode, ISRA and ISRB are injected n bytes after a JK, where n is the programmed value of the Injection Threshold

Register. In the Periodic mode, ISRA and ISRB are injected every n-th symbol pair. In the Continuous mode, all data symbols are

replaced with ISRA and ISRB.

ACCESS RULES

ADDRESS READ WRITE

06h Always Always

D7 D6 D5 D4 D3 D2 D1 D0

RES RES RES IJS4 IJS3 IJS2 IJS1 IJS0

Bit Symbol Description

D0–D4 IJS0–IJS4 INJECTION SYMBOL BITk0-4l:Symbol to be injected.

IJS0 is the Least Significant Bit (LSB) and goes out onto the media last.

D5–D7 RES RESERVED: Reserved for future use.

Note: Users are discouraged from using these bits. The reserved bits are set to 0 during the reset process. They may be set or cleared

without any effects to the functionality of the PLAYERadevice.

5.0 Registers (Continued)

5.8 INJECTION SYMBOL REGISTER B (ISRB)

The Injection Symbol Register B, along with Injection Symbol Register A, contains the programmable value (already in 5B code)

that will replace the data symbol pairs.

In One Shot mode, ISRA and ISRB are injected n bytes after a JK, where n is the programmed value of the Injection Threshold

Register. In the Periodic mode, ISRA and ISRB are injected every n-th symbol pair. In the Continuous mode, all data symbols are

replaced with ISRA and ISRB.

ACCESS RULES

ADDRESS READ WRITE

07h Always Always

D7 D6 D5 D4 D3 D2 D1 D0

RES RES RES IJS9 IJS8 IJS7 IJS6 IJS5

Bit Symbol Description

D0–D4 IJS0–IJS4 INJECTION SYMBOL BITk0-4l:Symbol to be injected.

IJS0 is the Least Significant Bit (LSB) and goes out onto the media last.

D5–D7 RES RESERVED: Reserved for future use.

Note: Users are discouraged from using these bits. The reserved bits are set to 0 during the reset process. They may be set or cleared

without any effects to the functionality of the PLAYERadevice.

5.0 Registers (Continued)

5.9 CURRENT RECEIVE STATE REGISTER (CRSR)

The Current Receive State Register represents the current line state being detected by the Receiver Block. When the Receiver

Block recognizes a new Line State, the bits corresponding to the previous line state are cleared, and the bits corresponding to

the new line state are set.

During the reset process (ERSTeGND), the Receiver Block is forced to Line State Unknown (i.e. the Line State Unknown bit

(LSU) is set to 1).

Note: Users are discouraged from writing to this register. An attempt to write into this register will cause the PLAYERadevice to ignore the Control Bus write cycle

and set the Control Bus Write Command Reject bit (CCR) of the Interrupt Condition Register (ICR) to 1.

ACCESS RULES

ADDRESS READ WRITE

08h Always Write Reject

D7 D6 D5 D4 D3 D2 D1 D0

RES RES RES RES LSU LS2 LS1 LS0

Bit Symbol Description

D0, LS0, LS1, LINE STATEk0, 1, 2l:These bits represent the current Line State being detected by the Receiver Block.

Once the Receiver Block recognizes a new line state, the bits corresponding to the previous line state are

D1, D2 LS2

cleared, and the bits corresponding to the new line state are set.

LS2 LS1 LS0

000Active Line State (ALS): Received a JK symbol pair (11000 10001), possibly followed

by data symbols.

001Idle Line State (ILS): Received a minimum of two consecutive Idle symbol pairs

(11111 11111).

010No Signal Detect (NSD): The Signal Detect (SD) has been deasserted, indicating that

the PLAYERadevice is not receiving data from the PMD receiver or that clock detect is

not being received from the Clock Recovery Module. SD is ignored during internal

loopback.

Note: NSD is the default value when the device is in Stop mode. However, while in Stop mode certain data

patterns entering the Receiver Block may cause the PLAYERato set LS0. Therefore, the user may see

either the NSD (010) or Reserved Value (011) during Stop mode.

011Reserved: Reserved for future use.

100Master Line State (MLS): Received a minimum of 8 consecutive Halt-Quiet symbol

pairs (00100 00000).

101Halt Line State (HLS): Received a minimum of 8 consecutive Halt symbol pairs

(00100 00100).

110Quiet Line State (QLS): Received a minimum of 8 consecutive Quiet symbol pairs

(00000 00000).

111Noise Line State (NLS): Detected a minimum of 16 noise events. Refer to the Receiver

Block description for further information on noise events.

D3 LSU LINE STATE UNKNOWN: The Receiver Block has not detected the minimum conditions to enter a known

line state. When the Line State Unknown bit is set, LSk2:0lrepresent the most recently known line state.

D4-D7 RES RESERVED: Reserved for future use.

Note: Users are discouraged from using these bits. The reserved bits are reset to 0 during the reset process. They may be set or cleared

without any effects to the functionality of the PLAYERadevice.

5.0 Registers (Continued)

5.10 RECEIVE CONDITION REGISTER A (RCRA)

The Receive Condition Register A maintains a historical record of the Line States recognized by the Receiver Block.

When a new Line State is entered, the bit corresponding to that line state is set to 1. The bits corresponding to the previous Line

States are not cleared by the PLAYERadevice, thereby maintaining a record of the Line States detected.

The Receive Condition A bit (RCA) of the Interrupt Condition Register (ICR) will be set to 1 when one or more bits within the

Receive Condition Register A is set to 1 and the corresponding mask bit(s) in Receive Condition Mask Register A (RCMRA) is

also set to 1.

ACCESS RULES

ADDRESS READ WRITE

09h Always Conditional

D7 D6 D5 D4 D3 D2 D1 D0

LSUPI LSC NT NLS MLS HLS QLS NSD

Bit Symbol Description

D0 NSD NO SIGNAL DETECT: Indicates that the Signal Detect pin (TTLSD) has been deasserted and that the Clock

Recovery Module is not receiving data from the PMD receiver.

D1 QLS QUIET LINE STATE: Received a minimum of eight consecutive Quiet symbol pairs (00000 00000).

D2 HLS HALT LINE STATE: Received a minimum of eight consecutive Halt symbol pairs (00100 00100).

D3 MLS MASTER LINE STATE: Received a minimum of eight consecutive Halt-Quiet symbol pairs (00100 00000).

D4 NLS NOISE LINE STATE: Detected a minimum of sixteen noise events.

D5 NT NOISE THRESHOLD: This bit is set to 1 when the internal Noise Counter reaches 0. It will remain set until a value

equal to or greater than one is loaded into the Noise Threshold Register or Noise Prescale Threshold Register.

During the reset process (i.e. ERSTeGND), since the Noise Counter is initialized to 0, the Noise Threshold bit will

be set to 1.

D6 LSC LINE STATE CHANGE: A line state change has been detected.

D7 LSUPI LINE STATE UNKNOWN AND PHY INVALID: The Receiver Block has not detected the minimum conditions to

enter a known line state.

In addition, the most recently known line state was one of the following line states: No Signal Detect, Quiet Line

State, Halt Line State, Master Line State, or Noise Line State.

5.0 Registers (Continued)

5.11 RECEIVE CONDITION REGISTER B (RCRB)

The Receive Condition Register B maintains a historical record of the Lines States recognized by the Receiver Block.

When a new Line State is entered, the bit corresponding to that line state is set to 1. The bits corresponding to the previous Line

States are not cleared, thereby maintaining a record of the Line States detected.

The Receive Condition B bit (RCB) of the Interrupt Condition Register (ICR) will be set to 1 when one or more bits within the

Receive Condition Register B is set to 1 and the corresponding mask bit(s) in Receive Condition Mask Register B (RCMRB) is

also set to 1.

ACCESS RULES

ADDRESS READ WRITE

0Ah Always Conditional

D7 D6 D5 D4 D3 D2 D1 D0

RES SILS EBOU CSE LSUPV ALS ST ILS

Bit Symbol Description

D0 ILS IDLE LINE STATE: Received a minimum of two consecutive Idle symbol pairs (11111 11111).

D1 ST STATE THRESHOLD: This bit will be set to 1 when the internal State Counter reaches zero. It will remain set until

a value equal to or greater than one is loaded into the State Threshold Register or State Prescale Threshold

During the reset process (i.e. ERSTeGND), since the State Counter is initialized to 0, the State Threshold bit is

set to 1.

D2 ALS ACTIVE LINE STATE: Received a JK symbol pair (11000 10001), and possibly data symbols following.

D3 LSUPV LINE STATE UNKNOWN AND PHY VALID: The Receiver Block has not detected the minimum conditions to

enter a known line state.

In addition, the most recently known line state was either Active Line State or Idle Line State.

D4 CSE CONNECTION SERVICE EVENT/CASCADE SYNCHRONIZATION ERROR:

When one or more bits in the CMT Condition Register (CMTCR) are set and the corresponding bit(s) in the CMT

Condition Mask Register (CMTCMR) are set, the Connection service event bit will be set to a 1.

When a synchronization error occurs, the Cascade Synchronization Error bit is set to 1. A synchronization error

occurs if the Cascade Start signal (CS) is not asserted within approximately 80 ns of Cascade Ready (CR) release.

Note: Cascade mode and the CMT features can not be used at the same time.

Note: Cascade mode is only supported on the DP83257 device.

D5 EBOU ELASTICITY BUFFER UNDERFLOW / OVERFLOW: The Elasticity Buffer has either overflowed or underflowed.

The Elasticity Buffer will automatically recover if the condition which caused the error is only transient, but the

event bit will remain set until cleared by software.

D6 SILS SUPER IDLE LINE STATE: Received a minimum of eight Idle symbol pairs (11111 11111).

D7 RES RESERVED: Reserved for future use.

Note: Users are discouraged from using these bits. The reserved bits are reset to 0 during the reset process. They may be set or cleared without

any effects to the functionality of the PLAYERadevice

5.0 Registers (Continued)

5.12 RECEIVE CONDITION MASK REGISTER A (RCMRA)

The Receive Condition Mask Register A allows the user to dynamically select which events will generate an interrupt.

The Receive Condition A bit (RCA) of the Interrupt Condition Register (ICR) will be set to 1 when one or more bits within the

Receive Condition Register A (RCRA) is set to 1 and the corresponding mask bit(s) in this register is also set to 1.

Since this register is cleared (i.e. set to 0) during the reset process, all interrupts are initially masked.

ACCESS RULES

ADDRESS READ WRITE

0Bh Always Always

D7 D6 D5 D4 D3 D2 D1 D0

LSUPIM LSCM NTM NLSM MLSM HLSM QLSM NSDM

Bit Symbol Description

D0 NSDM NO SIGNAL DETECT MASK: The mask bit for the No Signal Detect bit (NSD) of the Receive Condition Register A

(RCRA).

D1 QLSM QUIET LINE STATE MASK: The mask bit for the Quiet Line State bit (QLS) of the Receive Condition Register A

(RCRA).

D2 HLSM HALT LINE STATE MASK: The mask bit for the Halt Line State bit (HLS) of the Receive Condition Register A

(RCRA).

D3 MLSM MASTER LINE STATE MASK: The mask bit for the Master Line State bit (MLS) of the Receive Condition Register

A (RCRA).

D4 NLSM NOISE LINE STATE MASK: The mask bit for the Noise Line State bit (NLS) of the Receive Condition Register A

(RCRA).

D5 NTM NOISE THRESHOLD MASK: The mask bit for the Noise Threshold bit (NT) of the Receive Condition Register A

(RCRA).

D6 LSCM LINE STATE CHANGE MASK: The mask bit for the Line State Change bit (LSC) of the Receive Condition

D7 LSUPIM LINE STATE UNKNOWN AND PHY INVALID MASK: The mask bit for the Line State Unknown and PHY Invalid

bit (LSUPI) of the Receive Condition Register A (RCRA).

5.0 Registers (Continued)

5.13 RECEIVE CONDITION MASK REGISTER B (RCMRB)

The Receive Condition Mask Register B allows the user to dynamically select which events will generate an interrupt.

The Receive Condition B bit (RCB) of the Interrupt Condition Register (ICR) will be set to 1 when one or more bits within the

Receive Condition Register B (RCRA) is set to 1 and the corresponding mask bits in this register is also set to 1.

Since this register is cleared (i.e. set to 0) during the reset process, all interrupts are initially masked.

ACCESS RULES

ADDRESS READ WRITE

0Ch Always Always

D7 D6 D5 D4 D3 D2 D1 D0

RESM SILSM EBOUM CSEM LSUPVM ALSM STM ILSM

Bit Symbol Description

D0 ILSM IDLE LINE STATE MASK: The mask bit for the Idle Line State bit (ILS) of the Receive Condition Register B

(RCRB).

D1 STM STATE THRESHOLD MASK: The mask bit for the State Threshold bit (ST) of the Receive Condition Register B

(RCRB).

D2 ALSM ACTIVE LINE STATE MASK: The mask bit for the Active Line State bit (ALS) of the Receive Condition Register

B (RCRB).

D3 LSUPVM LINE STATE UNKNOWN AND PHY VALID MASK: The mask bit for the Line State Unknown and PHY Valid bit

(LSUPV) of the Receive Condition Register B (RCRB).

D4 CSEM CASCADE SYNCHRONIZATION ERROR MASK/CONNECTION SERVICE EVENT MASK:

The mask bit for the Cascade Synchronization Error/Connection service event bit (CSE) of the Receive Condition

D5 EBOUM ELASTICITY BUFFER OVERFLOW/UNDERFLOW MASK: The mask bit for the Elasticity Buffer Overflow/

Underflow bit (EBOU) of the Receive Condition Register B (RCRB).

D6 SILSM SUPER IDLE LINE STATE MASK: The mask bit for the Super Idle Line State bit (SILS) of the Receive Condition

D7 RESM RESERVED MASK: The mask bit for the Reserved bit (RES) of the Receive Condition Register B (RCRB).

5.0 Registers (Continued)

5.14 NOISE THRESHOLD REGISTER (NTR)

The Noise Threshold Register contains the start value for the Noise Timer. This threshold register is used in conjunction with the

Noise Prescale Threshold register for setting the maximum allowable time between entry to ILS, HLS, MLS, ALS, or NSD line

states. The Noise timer is used to implement the TNE timing requirement of PCM. The Noise timer decrements by one for every

80 x (NPTRa1) ns in case of Noise events. As a result, the internal noise counter takes the following amount of time to reach

zero:

((NPTRa1) x NTR aNPTR) x 80 ns

The threshold values for the Noise Counter and Noise Prescale Counter are simultaneously loaded into both counters if one of

the following conditions is true:

1. Both the Noise Counter and Noise Prescale Counter reach zero and the current Line State is either Noise Line State, Active

Line State, or Line State Unknown.

2. The current Line State is either Halt Line State, Idle Line State, Master Line State, Quiet Line State, or No Signal Detect.

3. The Noise Threshold Register or Noise Prescale Threshold Register goes through a Control Bus Interface write cycle.

In addition, the value of the Noise Prescale Threshold register is loaded into the Noise Prescale Counter if the Noise Prescale

Counter reaches zero.

The Noise Counter and Noise Prescale Counter will continue to count, without resetting or reloading the threshold values, if a

Line State change occurs and the new line state is either Noise Line State, Active Line State, or Line State Unknown.

When both the Noise Threshold Counter and Noise Counter both reach zero, the Noise Threshold bit of the Receive Condition

The recommended default value for the NTR register is 40h and for the NPTR register is F9h which corresponds to 1.3 ms as

specified in the ANSI standard.

ACCESS RULES

ADDRESS READ WRITE

0Dh Always Always

D7 D6 D5 D4 D3 D2 D1 D0

RES NT6 NT5 NT4 NT3 NT2 NT1 NT0

Bit Symbol Description

D0-D6 NT0-NT6 NOISE THRESHOLD BITk0-6l:Start value for the Noise Counter.

NT0 is the Least Significant Bit (LSB).

D7 RES RESERVED: Reserved for future use.

Note: Users are discouraged from using this bit. Write data is ignored since the reserved bit is permanently set to 0.

5.0 Registers (Continued)

5.15 NOISE PRESCALE THRESHOLD REGISTER (NPTR)

The Noise Prescale Threshold Register contains the start value for the Noise Prescale Timer. This threshold register is used in

conjunction with the Noise Threshold register for setting the maximum allowable time between entry to ILS, HLS, MLS, ALS, or

NSD. The Noise timer is used to implement the TNE timing requirement of PCM. The Noise Prescale threshold controls how

often the Noise timer is decremented. When the Noise Prescale Timer reaches zero, it reloads the count with the contents of the

Noise Prescale Threshold Register and also causes the Noise Timer to decrement.

The threshold values for the Noise Counter and Noise Prescale Counter are simultaneously loaded into both counters if one of

the following conditions is true:

1. Both the Noise Counter and Noise Prescale Counter reach zero and the current Line State is either Noise Line State, Active

Line State, or Line State Unknown.

2. The Current Line State is either Halt Line State. Idle Line State, Master Line State, Quiet Line State, or No Signal Detect

3. The Noise Threshold Register or Noise Prescale Threshold Register goes through a Control Bus Interface write cycle.

In addition, the value of the Noise Prescale Threshold Register is loaded into the Noise Prescale Counter if the Noise Prescale

Counter reaches zero.

The Noise Counter and Noise Prescale Counter will continue to count, without resetting or reloading the threshold values, if a

Line State change occurs and the new line state is either Noise Line State, Active Line State, or Line State Unknown.

When both the Noise Threshold Counter and Noise Counter both reach zero, the Noise Threshold bit of the Receive Condition

See the NTR register description for default value recommendations.

ACCESS RULES

ADDRESS READ WRITE

0Eh Always Always

D7 D6 D5 D4 D3 D2 D1 D0

NPT7 NPT6 NPT5 NPT4 NPT3 NPT2 NPT1 NPT0

Bit Symbol Description

D0-D7 NPT0-NPT7 NOISE PRESCALE THRESHOLD BITk0-7l:Start value for the Noise Prescale Timer.

NPT0 is the Least Significant Bit (LSB).

5.0 Registers (Continued)

5.16 CURRENT NOISE COUNT REGISTER (CNCR)

The Current Noise Count Register takes a snap-shot of the Noise Timer during every Control Bus Interface read cycle of this

During a Control Bus Interface write cycle, the Control Bus Write Command Reject bit (CCR) of the Interrupt Condition Register

(ICR) will be set to 1 and will ignore a write cycle.

ACCESS RULES

ADDRESS READ WRITE

0Fh Always Write Reject

D7 D6 D5 D4 D3 D2 D1 D0

NCLSCD CNC6 CNC5 CNC4 CNC3 CNC2 CNC1 CNC0

Bit Symbol Description

D0–D6 CNC0–CNC6 CURRENT NOISE COUNT BIT k0–6l:Snapshot of the Noise Counter.

D7 NCLSCD NOISE COUNTER LINE STATE CHANGE DETECTION

5.0 Registers (Continued)

5.17 CURRENT NOISE PRESCALE COUNT REGISTER (CNPCR)

The Current Noise Prescale Count Register takes a snap-shot of the Noise Prescale Timer during every Control Bus Interface

read cycle of this register.

During a Control Bus Interface write cycle, the Control Bus Write Command Reject bit (CCR) of the Interrupt Condition Register

(ICR) will be set to 1 and will ignore a write cycle.

ACCESS RULES

ADDRESS READ WRITE

10h Always Write Reject

D7 D6 D5 D4 D3 D2 D1 D0

CNPC7 CNPC6 CNPC5 CNPC4 CNPC3 CNPC2 CNPC1 CNPC0

Bit Symbol Description

D0–D7 CNPC0–7 CURRENT NOISE PRESCALE COUNT BIT k0–7l:Snapshot of the Noise Prescale Timer.

5.0 Registers (Continued)

5.18 STATE THRESHOLD REGISTER (STR)

The State Threshold Register contains the start value for the State Timer. This timer is used in conjunction with the State

Prescale Timer to count the Line State duration. The State Timer will decrement every 80 ns if the State Prescale Timer is zero

and the current Line State is Halt Line State, Idle Line State, Master Line State, Quiet Line State, or No Signal Detect. The State

Timer takes

((SPTRa1) x STR aSPTR) x 80 ns

to reach zero during a continuous line state condition.

The threshold values for the State Timer and State Prescale Timer are simultaneously loaded into both counters if one of the

following conditions is true:

1. Both the State Timer and State Prescale Timer reach zero and the current Line State is Halt Line State, Idle Line State,

Master Line State, Quiet Line State, or No Signal Detect.

2. A line state change occurs and the new Line State is Halt Line State, Idle Line State, Master Line State, Quiet Line State, or

No Signal Detect.

3. The State Threshold Register or State Prescale Threshold Register goes through a Control Bus Interface write cycle.

In addition, the value of the State Prescale Threshold Register is loaded into the State Prescale Counter if the State Prescale

Timer reaches zero.

The State Timer and State Prescale Timer will reset by reloading the threshold values, if a Line State change occurs and the

new Line State is Halt Line State, Idle Line State, Master Line State, Quiet Line State, or No Signal Detect. On detection of ALS,

NLS, or LSU the timer will not decrement.

ACCESS RULES

ADDRESS READ WRITE

11h Always Always

D7 D6 D5 D4 D3 D2 D1 D0

RES ST6 ST5 ST4 ST3 ST2 ST1 ST0

Bit Symbol Description

D0-D6 ST0-ST6 STATE THRESHOLD BITk0-6l:Start value for the State Timer.

ST0 is the Least Significant Bit (LSB).

D7 RES RESERVED: Reserved for future use.

Note: Users are discouraged from using this bit. Write data is ignored since the reserved bit is permanently set to 0.

5.0 Registers (Continued)

5.19 STATE PRESCALE THRESHOLD REGISTER (SPTR)

The State Prescale Threshold Register contains the start value for the State Prescale Timer. The State Prescale Timer is a down

counter. It is used in conjunction with the State Timer to count the Line State duration.

The threshold values for the State Timer and State Prescale Timer are simultaneously loaded into both timers if one of the

following conditions is true:

1. Both the State Timer and State Prescale Timer reach zero and the current Line State is Halt Line State, Idle Line State,

Master Line State, Quiet Line State, or No Signal Detect.

2. A Line State change occurs and the new Line State is Halt Line State, Idle Line State, Master Line State, Quiet Line State, or

No Signal Detect.

3. The State Threshold Register or State Prescale Threshold Register goes through a Control Bus Interface write cycle.

The State Prescale Timer will decrement every 80 ns if the current Line State is Halt Line State, Idle Line State, Master Line

State, Quiet Line State, or No Signal Detect.

ACCESS RULES

ADDRESS READ WRITE

12h Always Always

D7 D6 D5 D4 D3 D2 D1 D0

SPT7 SPT6 SPT5 SPT4 SPT3 SPT2 SPT1 SPT0

Bit Symbol Description

D0–D7 SPT0–SPT7 STATE PRESCALE THRESHOLD BIT k0–7l:Start value for the State Prescale Timer.

SPT0 is the Least Significant Bit (LSB).

5.0 Registers (Continued)

5.20 CURRENT STATE COUNT REGISTER (CSCR)

The Current State Count Register takes a snap-shot of the State Counter during every Control Bus Interface read cycle of this

During a Control Bus Interface write cycle, the Control Bus Write Command Reject bit (CCR) of the Interrupt Condition Register

(ICR) will be set to 1 and will ignore a write cycle.

ACCESS RULES

ADDRESS READ WRITE

13h Always Write Reject

D7 D6 D5 D4 D3 D2 D1 D0

SCLSCD CSC6 CSC5 CSC4 CSC3 CSC2 CSC1 CSC0

Bit Symbol Description

D0–D6 CSC0–CSC6 CURRENT STATE COUNT BIT k0–6l:Snapshot of the State Counter.

D7 SCLSCD STATE COUNTER LINE STATE CHANGE DETECTION

5.0 Registers (Continued)

5.21 CURRENT STATE PRESCALE COUNT REGISTER (CSPCR)

The Current State Prescale Count Register takes a snap-shot of the State Prescale Counter during every Control Bus Interface

read cycle of this register.

During a Control Bus Interface write cycle, the Control Bus Write Command Reject bit (CCR) of the Interrupt Condition Register

(ICR) will be set to 1 and will ignore a write cycle.

ACCESS RULES

ADDRESS READ WRITE

14h Always Write Reject

D7 D6 D5 D4 D3 D2 D1 D0

CSPC7 CSPC6 CSPC5 CSPC4 CSPC3 CSPC2 CSPC1 CSPC0

Bit Symbol Description

D0–D7 CSPC0–7 CURRENT STATE PRESCALE COUNT k0–7l:Snapshot of the State Prescale Counter.

5.0 Registers (Continued)

5.22 LINK ERROR THRESHOLD REGISTER (LETR)

The Link Error Threshold Register contains the start value for the Link Error Monitor Counter. It is an 8-bit down-counter which

decrements if link errors are detected.

When the Counter reaches 0, the Link Error Monitor Threshold Register value is loaded into the Link Error Monitor Counter and

the Link Error Monitor Threshold bit (LEMT) of the Interrupt Condition Register (ICR) is set to one.

The Link Error Monitor Threshold Register value is also loaded into the Link Error Monitor Counter during every Control Bus

Interface write cycle of LETR.

The counter is initialized to 0 during the reset process (i.e. ERSTeGND).

ACCESS RULES

ADDRESS READ WRITE

15h Always Always

D7 D6 D5 D4 D3 D2 D1 D0

LET7 LET6 LET5 LET4 LET3 LET2 LET1 LET0

Bit Symbol Description

D0–D7 LET0–LET7 LINK ERROR THRESHOLD BIT k0–7l:Start value for the Link Error Monitor Counter.

LET0 is the Least Significant Bit (LSB).

5.0 Registers (Continued)

5.23 CURRENT LINK ERROR COUNT REGISTER (CLECR)

The Current Link Error Count Register takes a snap-shot of the Link Error Monitor Counter during every Control Bus Interface

read cycle of this register.

During a Control Bus Interface write cycle, the Control Bus Write Command Reject bit (CCR) of the Interrupt Condition Register

(ICR) will be set to 1 and will ignore a write cycle.

ACCESS RULES

ADDRESS READ WRITE

16h Always Write Reject

D7 D6 D5 D4 D3 D2 D1 D0

LEC7 LEC6 LEC5 LEC4 LEC3 LEC2 LEC1 LEC0

Bit Symbol Description

D0–D7 LEC0–LEC7 LINK ERROR COUNT BIT k0–7l:Snapshot of the Link Error Monitor Counter.

5.0 Registers (Continued)

5.24 USER DEFINABLE REGISTER (UDR)

The User Definable Register is used to monitor and control events which are external to the PLAYERadevice.

The value of the Sense Bits reflect the asserted/deasserted state of their corresponding Sense pins. On the other hand, the

Enable bits assert/deassert the Enable pins.

Note: SB2 and EB2 are only effective for the DP83257.

ACCESS RULES

ADDRESS READ WRITE

17h Always Always

D7 D6 D5 D4 D3 D2 D1 D0

RES EB2 RES SB2 EB1 EB0 SB1 SB0

Bit Symbol Description

D0 SB0 SENSE BIT 0: This bit is set to 1 if the Sense Pin 0 (SP0) is asserted (i.e. SP0eVCC) for a minimum amount of

time. Once the asserted signal is latched, Sense Bit 0 can only be cleared through the Control Bus Interface, even

if the signal is deasserted. This ensures that the Control Bus Interface will record the source of events which can

cause interrupts in a traceable manner.

D1 SB1 SENSE BIT 1: This bit is set to 1 if the Sense Pin 1 (SP1) is asserted (i.e. SP1eVCC) for a minimum amount of

time. Once the asserted signal is latched, Sense Bit 1 can only be cleared through the Control Bus Interface, even

if the signal is deasserted. This ensures that the Control Bus Interface will record the source of events which can

cause interrupts in a traceable manner.

D2 EB0 ENABLE BIT 0: The Enable Bit 0 allows control of external logic through the Control Bus Interface. The User

Definable Enable Pin 0 (EP0) is asserted/deasserted by this bit.

0: EP0 is deasserted (i.e. EP0eGND).

1: EP0 is asserted (i.e. EP0eVCC).

D3 EB1 ENABLE BIT 1: This bit allows control of external logic through the Control Bus Interface. The User Definable

Enable Pin 0 (EP0) is asserted/deasserted by this bit.

0: EP1 is deasserted (i.e. EP1eGND).

1: EP1 is asserted (i.e. EP1eVCC).

D4 SB2 SENSE BIT 2: This bit is set to 1 if the Sense Pin 2 (SP2) is asserted (i.e. SP2eVCC) for a minimum amount of

time. Once the asserted signal is latched, Sense Bit 2 can only be cleared through the Control Bus Interface, even

if the signal is deasserted. This ensures that the Control Bus Interface will record the source of events which can

cause interrupts in a traceable manner.

Note: SB2 and EB2 are only effective for the DP83257.

D5 RES RESERVED: Reserved for future use. The reserved bit is set to 0 during the initialization process

(i.e. ERSTeGND).

Note: Users are discouraged from using this bit. It may be set or cleared without any effects to the functionality of the PLAYERadevice.

D6 EB2 ENABLE BIT2: The Enable Bit 2 allows control of external logic through the Control Bus Interface. The User

Definable Enable Pin 2 (EP2) is asserted/deasserted by this bit.

Note: SB2 and EB2 are only effective for the DP83257.

0: EP2 is deasserted (i.e. EP2eGND).

1: EP2 is asserted (i.e. EP2eVCC).

D7 RES RESERVED: Reserved for future use. The reserved bit is set to 0 during the initialization process

(i.e. ERSTeGND).

Note: Users are discouraged from using this bit. It may be set or cleared without any effects to the functionality of the PLAYERadevice.

5.0 Registers (Continued)

5.25 DEVICE ID REGISTER (IDR)

The Device ID Register contains the binary equivalent of the revision number for this device. It can be used to ensure proper

software and hardware versions are matched.

During a Control Bus Interface write cycle, the Control Bus Write Command Register bit (CCR) of the Interrupt Condition

REVISION TABLE

IDR DEVICE DESCRIPTION

(hex)

10 PLAYERaRevision A

11 PLAYERaRevision B

ACCESS RULES

ADDRESS READ WRITE

18h Always Write Reject

D7 D6 D5 D4 D3 D2 D1 D0

DID7 DID6 DID5 DID4 DID3 DID2 DID1 DID0

Bit Symbol Description

D0–D3 DID0–DID3 DEVICE ID BIT k0-3l:Circuit enhancement revision number. Bit 3 is the MSB. The initial revision of the

PLAYERais equal to 0 and enhancements will increment this number.

D4–D7 DID4–DID7 DEVICE ID BIT k4-7l:Architecture level of the PHY device. Bit 7 is the MSB. The original PLAYER

device was equal to 0 and the PLAYERais equal to 1. This number will only be incremented after a

significant architectural change.

5.0 Registers (Continued)

5.26 CURRENT INJECTION COUNT REGISTER (CIJCR)

The Current Injection Count Register takes a snap-shot of the Injection Counter during every Control Bus Interface read cycle of

this register.

During a Control Bus Interface write cycle, the Control Bus Write Command Reject bit (CCR) of the Interrupt Condition Register

(ICR) will be set to 1 and will ignore a write cycle.

The Injection Counter is an 8-bit down-counter which decrements every 80 ns.

The counter is active only during One Shot or Periodic Injection Modes (i.e. Injection Controlk1:0lbits (ICk1:0l)ofthe

Current Transmit State Register (CTSR) are set to either 01 or 10).

The Injection Threshold Register (IJTR) value is loaded into the Injection Counter when the counter reaches zero and during

every Control Bus Interface write cycle of IJTR.

The counter is initialized to 0 during the reset process (i.e. ERSTeGND).

ACCESS RULES

ADDRESS READ WRITE

19h Always Write Reject

D7 D6 D5 D4 D3 D2 D1 D0

IJC7 IJC6 IJC5 IJC4 IJC3 IJC2 IJC1 IJC0

Bit Symbol Description

D0–D7 IJC0–IJC7 INJECTION COUNT BITk0-7l:Current value of the Injection Counter.

IJC0 is the Least Significant Bit (LSB).

5.0 Registers (Continued)

5.27 INTERRUPT CONDITION COMPARISON REGISTER (ICCR)

The Interrupt Condition Comparison Register ensures that the Control Bus must first read a bit modified by the PLAYERa

device before it can be written to by the Control Bus Interface.

The current state of the Interrupt Condition Register (ICR) is automatically written into the Interrupt Condition Comparison

During a Control Bus Interface write cycle, the PLAYERadevice will set the Conditional Write Inhibit bit (CWI) of the Interrupt

Condition Register (ICR) to 1 and disallow the setting or clearing of a bit within ICR when the value of a bit in ICR differs from the

value of the corresponding bit in the interrupt Condition Comparison Register.

ACCESS RULES

ADDRESS READ WRITE

1Ah Always Always

D7 D6 D5 D4 D3 D2 D1 D0

UDIC RCBC RCAC LEMTC CWIC CCRC CPEC DPEC

Bit Symbol Description

D0 DPEC PHYÐREQUEST DATA PARITY ERROR COMPARISON: The comparison bit for the PHYÐRequest Data Parity

Error bit (DPE) of the Interrupt Condition Register (ICR).

D1 CPEC CONTROL BUS DATA PARITY ERROR COMPARISON: The comparison bit for the Control Bus Data Parity Error

bit (CPE) of the Interrupt Condition Register (ICR).

D2 CCRC CONTROL BUS WRITE COMMAND REJECT COMPARISON: The comparison bit for the Control Bus Write

Command Reject bit (CCR) of the Interrupt Condition Register (ICR).

D3 CWIC CONDITIONAL WRITE INHIBIT COMPARISON: The comparison bit for the Conditional Write Inhibit bit (CWI) of

the Interrupt Condition Register (ICR).

D4 LEMTC LINK ERROR MONITOR THRESHOLD COMPARISON: The comparison bit for the Link Error Monitor Threshold

bit (LEMT) of the Interrupt Condition Register (ICR).

D5 RCAC RECEIVE CONDITION A COMPARISON: The comparison bit for the Receive Condition A bit (RCA) of the

Interrupt Condition Register (ICR).

D6 RCBC RECEIVE CONDITION B COMPARISON: The comparison bit for the Receive Condition B bit (RCB) of the

Interrupt Condition Register (ICR).

D7 UDIC USER DEFINABLE INTERRUPT COMPARISON: The comparison bit for the User Definable Interrupt bit (UDIC) of

the Interrupt Condition Register (ICR).

5.0 Registers (Continued)

5.28 CURRENT TRANSMIT STATE COMPARISON REGISTER (CTSCR)

The Current Transmit State Comparison Register ensures that the Control Bus must first read a bit modified by the PLAYERa

device before it can be written to by the Control Bus Interface.

The current state of the Current Transmit State Register (CTSR) is automatically written into the Current Transmit State

Comparison Register A (i.e. CTSCReCTSR) during a Control Bus Interface read cycle of CTSR.

During a Control Bus Interface write cycle, the PLAYERadevice will set the Conditional Write Inhibit bit (CWI) of the Interrupt

Condition Register (ICR) to 1 and disallow the setting or clearing of a bit within the CTSR when the value of a bit in the CTSR

differs from the value of the corresponding bit in the Current Transmit State Comparison Register.

ACCESS RULES

ADDRESS READ WRITE

1Bh Always Always

D7 D6 D5 D4 D3 D2 D1 D0

RESC PRDPEC SEC IC1C IC0C TM2C TM1C TM0C

Bit Symbol Description

D0 TM0C TRANSMIT MODE k0lCOMPARISON: The comparison bit for the Transmit Mode k0lbit (TM0) of the

Current Transmit State Register (CTSR).

D1 TM1C TRANSMIT MODE k1lCOMPARISON: The comparison bit for the Transmit Mode k1lbit (TM1) of the

Current Transmit State Register (CTSR).

D2 TM2C TRANSMIT MODE k2lCOMPARISON: The comparison bit for the Transmit Mode k2lbit (TM2) of the

Current Transmit State Register (CTSR).

D3 IC0C INJECTION CONTROL k0lCOMPARISON: The comparison bit for the Injection Control k0lbit (IC0) of the

Current Transmit State Register (CTSR).

D4 IC1C INJECTION CONTROL k1lCOMPARISON: The comparison bit for the Injection Control k1lbit (IC1) of the

Current Transmit State Register (CTSR).

D5 SEC SMOOTHER ENABLE COMPARISON: The comparison bit for the Smoother Enable bit (SE) of the Current

Transmit State Register (CTSR).

D6 PRDPEC PHYÐREQUEST DATA PARITY ENABLE COMPARISON: The comparison bit for the PHYÐRequest Data

Parity Enable bit (PRDPE) of the Current Transmit State Register (CTSR).

D7 RESC RESERVED COMPARISON: The comparison bit for the Reserved bit (RES) of the Current Transmit State

5.0 Registers (Continued)

5.29 RECEIVE CONDITION COMPARISON REGISTER A (RCCRA)

The Receive Condition Comparison Register A ensures that the Control Bus must first read a bit modified by the PLAYERa

device before it can be written to by the Control Bus Interface.

The current state of RCRA is automatically written into the Receive Condition Comparison Register A (i.e. RCCRAeRCRA)

during a Control Bus Interface read cycle of RCRA.

During a Control Bus Interface write cycle, the PLAYERadevice will set the Conditional Write Inhibit bit (CWI) of the Interrupt

Condition Register (ICR) to 1 and prevent the setting or clearing of a bit within RCRA when the value of a bit in RCRA differs

from the value of the corresponding bit in the Receive Condition Comparison Register A.

ACCESS RULES

ADDRESS READ WRITE

1Ch Always Always

D7 D6 D5 D4 D3 D2 D1 D0

LSUPIC LSCC NTC NLSC MLSC HLSC QLSC NSDC

Bit Symbol Description

D0 NSDC NO SIGNAL DETECT COMPARISON: The comparison bit for the No Signal Detect bit (NSD) of the Receive

Condition Register A (RCRA).

D1 QLSC QUIET LINE STATE COMPARISON: The comparison bit for the Quiet Line State bit (QLS) of the Receive

Condition Register A (RCRA).

D2 HLSC HALT LINE STATE COMPARISON: The comparison bit for the Halt Line State bit (HLS) of the Receive Condition

D3 MLSC MASTER LINE STATE COMPARISON: The comparison bit for the Master Line State bit (MLS) of the Receive

Condition Register A (RCRA).

D4 NLSC NOISE LINE STATE COMPARISON: The comparison bit for the Noise Line State bit (NLS) of the Receive

Condition Register A (RCRA).

D5 NTC NOISE THRESHOLD COMPARISON: The comparison bit for the Noise Threshold bit (NT) of the Receive

Condition Register A (RCRA).

D6 LSCC LINE STATE CHANGE COMPARISON: The comparison bit for the Line State Change bit (LSC) of the Receive

Condition Register A (RCRA).

D7 LSUPIC LINE STATE UNKNOWN AND PHY INVALID COMPARISON: The comparison bit for the Line State Unknown

and PHY Invalid bit (LSUPI) of the Receive Condition Register A (RCRA).

5.0 Registers (Continued)

5.30 RECEIVE CONDITION COMPARISION REGISTER B (RCCRB)

The Receive Condition Comparison Register B ensures that the Control Bus must first read a bit modified by the PLAYERa

device before it can be written to by the Control Bus Interface.

The current state of RCRB is automatically written into the Receive Condition Comparison Register B (i.e. RCCRBeRCRB)

during a Control Bus Interface read cycle RCRB.

During a Control Bus Interface write cycle, the PLAYERadevice will set the Conditional Write Inhibit bit (CWI) of the Interrupt

Condition Register (ICR) to 1 and prevent the setting or clearing of a bit within RCRB when the value of a bit in RCRB differs

from the value of the corresponding bit in the Receive Condition Comparison Register B.

ACCESS RULES

ADDRESS READ WRITE

1Dh Always Always

D7 D6 D5 D4 D3 D2 D1 D0

RESC SILSC EBOUC CSEC LSUPVC ALSC STC ILSC

Bit Symbol Description

D0 ILSC IDLE LINE STATE COMPARISON: The comparison bit for the Idle Line State bit (ILS) of the Receive Condition

D1 STC STATE THRESHOLD COMPARISON: The comparison bit for the State Threshold bit (ST) of the Receive

Condition Register B (RCRB).

D2 ALSC ACTIVE LINE STATE COMPARISON: The comparison bit for the Active Line State bit (ALS) of the Receive

Condition Register B (RCRB).

D3 LSUPVC LINE STATE UNKNOWN AND PHY VALID COMPARISON: The comparison bit for the Line State Unknown and

PHY Valid bit (LSUPV) of the Receive Condition Register B (RCRB).

D4 CSEC CONNECTION SERVICE EVENT COMPARISON / CASCADE SYNCHRONIZATION ERROR: The comparison

bit for the Cascade Synchronization Error/Connection Service Event bit (CSE) of the Receive Condition Register

B (RCRB).

D5 EBOUC ELASTICITY BUFFER OVERFLOW / UNDERFLOW COMPARISON: The comparison bit for the Elasticity Buffer

Overflow/Underflow bit (EBOU) of the Receive Condition Register B (RCRB).

D6 SILSC SUPER IDLE LINE STATE COMPARISON: The comparison bit for the Super Idle Line State bit (SILS) of the

Receive Condition Register B (RCRB).

D7 RESC RESERVED COMPARISON: The comparison bit for the Reserved bit (RES) of the Receive Condition Register B

(RCRB).

5.0 Registers (Continued)

5.31 MODE REGISTER 2 (MODE2)

The Mode Register 2 (MODE2) is used to configure the PLAYERadevice.

The register is used to software reset the chip, setup data parity, and enable scrubbing functions.

Note: This register can not be written to during reset.

ACCESS RULES

ADDRESS READ WRITE

1Eh Always Conditional

D7 D6 D5 D4 D3 D2 D1 D0

ESTC RES CLKSEL RES RES RES CBPE PHYRST

Bit Symbol Description

D0 PHYRST PLAYER RESET: This bit can be used as a master software reset of the PLAYER function within the

PLAYERadevice. The clock distribution and recovery sections of the chip are not affected by this reset.

The PLAYERaautomatically clears this bit 32 byte time after its assertion to indicate that the reset action

has been completed.

This bit can be set through a C-Bus write, but can only be cleared by the PLAYERa.

D1 CBPE C-Bus Parity Enable: This bit disables or enables parity checking on C-Bus data. When this bit is set to 0, no

parity checking is done. When the bit is set to 1, parity checking is enabled during a C-Bus write cycle. Should

a mismatch occur, the C-Bus Data Parity Error (ICR.CPE) bit will be set and the corresponding C-Bus access

is discarded.

C-Bus data parity is always generated during a C-Bus read cycle.

D2–D4 RES RESERVED: Reserved for future use.

D5 CLKSEL CLOCK SELECT: This bit controls the frequency of the CLK16 output. It resets to 0 which sets the CLK16

output to a 15.625 MHz frequency. When set to 1 a 31.25 MHz frequency is generated.

Note: When the value of this bit is changed, no glitches appear on the CLK16 output due to the frequency change.

D6 RES RESERVED: Reserved for future use.

D7 ESTC ENABLE SCRUBBING on TRIGGER CONDITIONS: When ESTC is set to 1 and a Trigger Condition occurs

(as set in the TDR register), the Trigger Transition Configuration Register (TTCR) is loaded into the

Configuration Register (CR) and scrubbing is started on all indicate ports that have changed.

Scrubbing is accomplished by sending out 2 PhyÐInvalid symbols followed by ‘‘scrub’’symbol pairs for a time

defined by the Scrub Timer Threshold register.

5.0 Registers (Continued)

5.32 CMT CONDITION COMPARISON REGISTER (CMTCCR)

The CMT Condition Comparison Register (CMTCR) ensures that the Control Bus must first read a bit modified by the PLAYERa

device before it can be written to by the Control Bus Interface.

The current state of the CMT Condition Register (CMTCR) is automatically written into the CMT Condition Comparison Register

(CMTCR) (i.e. CMTCCR eCMTCR) during a Control Bus Interface read-cycle of CMTCR.

During a Control Bus Interface write cycle, the PLAYERadevice will set the Conditional Write Inhibit bit (CWI) of the Interrupt

Control Register (ICR) to 1 and disallow the setting or clearing of a bit within the CMTCR when the value of a bit in the CMTCR

differs from the value of the corresponding bit in the CMT Condition Comparison Register.

ACCESS RULES

ADDRESS READ WRITE

1Fh Always Always

D7 D6 D5 D4 D3 D2 D1 D0

TCOC STEC RES RES RES RES RES RES

Bit Symbol Description

D0-D5 RES RESERVED: Reserved for future use.

D6 STEC SCRUB TIMER EXPIRED COMPARISON: The comparison bit for the Scrub Timer Expire bit (STE) of the CMT

Condition Register (CMTCR).

D7 TCOC TRIGGER CONDITION OCCURRED COMPARISON: The comparison bit for the Trigger Condition Occurred

(TCO) bit of the CMT Condition Register (CMTCR).

5.0 Registers (Continued)

5.33 CMT CONDITION REGISTER (CMTCR)

The CMT Condition Register maintains a history of all CMT events and actions performed. The corresponding CMT Condition

Mask Register (CMTCMR) can be used to generate an interrupt. When the bits in both the CMTCMR and CMTCR are set, the

Receive Condition Register B’s Connection Service Event (RCRB.CSE) bit will be set.

ACCESS RULES

ADDRESS READ WRITE

20h Always Conditional

D7 D6 D5 D4 D3 D2 D1 D0

TCO STE RES RES RES RES RES RES

Bit Symbol Description

D0-D5 RES RESERVED: Reserved for future use.

D6 STE SCRUB TIMER EXPIRED: This bit is set to 1 when the Scrub Timer expires.

Note: When STE is set, the Configuration Register (CR) is protected.

D7 TCO TRIGGER CONDITION OCCURRED: This bit is set to 1 when a trigger condition is met. When a trigger occurs,

the values in the Trigger Transmit Mode (TDR.TTM2-0) are loaded into the Current Transmit Mode Register

(CTSR.TM2-0).

Note: When TCO is set, the Current Transmit State Register (CTSR) is protected.

5.0 Registers (Continued)

5.34 CMT CONDITION MASK REGISTER (CMTCMR)

This is the mask register for the CMT Condition Register (CMTCR). When the bits in both the CMTCMR and CMTCR are set, the

Receive Condition Register B’s Connection Service Event (RCRB.CSE) bit will be set.

ACCESS RULES

ADDRESS READ WRITE

21h Always Always

D7 D6 D5 D4 D3 D2 D1 D0

TCOM STEM RES RES RES RES RES RES

Bit Symbol Description

D0-D5 RES RESERVED: Reserved for future use.

D6 STEM SCRUB TIMER EXPIRED MASK: The mask bit for the Scrub Timer Expired (STE) bit of the CMT Condition

D7 TCOM TRIGGER CONDITION OCCURRED MASK: The mask bit for the Trigger Condition Occurred (TCO) bit of the

CMT Condition Register (CMTCR).

5.0 Registers (Continued)

5.35 RESERVED REGISTERS 22H–23H (RR22H–RR23H)

This register is reserved for future use.

DO NOT ACCESS THIS REGISTER

ACCESS RULES

ADDRESS READ WRITE

22h–23h Always DO NOT WRITE

5.0 Registers (Continued)

5.36 SCRUB TIMER THRESHOLD REGISTER (STTR)

This is the threshold value of the internal scrub timer. It has a resolution of 40.96 ms and a maximum value of E10 ms. When

the scrub timer reaches zero, the Scrub Timer Expired (CMTCR.STE) bit is set.

Scrubbing is initiated when MODE2.ESTCe1 and a trigger condition occurs.

Writing to STTR during scrubbing will not affect the scrubbing action.

ACCESS RULES

ADDRESS READ WRITE

24h Always Always

D7 D6 D5 D4 D3 D2 D1 D0

STT7 STT6 STT5 STT4 STT3 STT2 STT1 STT0

Bit Symbol Description

D0–D7 STT0–STT7 SCRUB TIMER THRESHOLD BITk0-7l:Scrub Timer threshold.

STT0 is the Least Significant Bit (LSB).

5.0 Registers (Continued)

5.37 SCRUB TIMER VALUE REGISTER (STVR)

This is a snap-shot of the current value of the upper 8 bits of the scrub timer.

During a Control Bus Interface write cycle, the Control Bus Write Command Reject bit (CCR) of the Interrupt Condition Register

(ICR) will be set to 1 and will ignore a write cycle.

ACCESS RULES

ADDRESS READ WRITE

25h Always Write Reject

D7 D6 D5 D4 D3 D2 D1 D0

STV7 STV6 STV5 STV4 STV3 STV2 STV1 STV0

Bit Symbol Description

D0–D7 STV0–STV7 SCRUB TIMER VALUE BITk0-7l:Snap-shot of the scrub timer.

STV0 is the Least Significant Bit (LSB).

5.0 Registers (Continued)

5.38 TRIGGER DEFINITION REGISTER (TDR)

This register determines which events cause a trigger transition and which transmit mode is entered when a trigger transition is

detected. The trigger transmit modes are the same as those found in the Current Transmit State Register (CTSR), and are

loaded from the TDR into the CTSR when any of the selected trigger conditions occur. When a trigger condition occurs

CMTCR.TCO is set.

The Trigger Definition Register is useful to implement the strict PCÐReact time requirement.

ACCESS RULES

ADDRESS READ WRITE

26h Always Always

D7 D6 D5 D4 D3 D2 D1 D0

TONT TOQLS TOHLS TOMLS TOSILS TTM2 TTM1 TTM0

Bit Symbol Description

D0, TTM0, TRIGGER TRANSMIT MODE k0, 1, 2l:These bits select one of 6 transmission modes to be loaded into the

Current Transmit State Register (CTSR) when a trigger condition is detected. The trigger condition is selected by

D1, TTM1,

the upper 5 bits of this register.

D2 TTM2

TTM2 TTM1 TTM0

000Active Transmit Mode (ATM): Normal transmission of incoming PHY Request data.

001Idle Transmit Mode (ITM): Transmission of Idle symbol pairs (11111 11111).

010Off Transmit Mode (OTM): Transmission of Quiet symbol pairs (00000 00000) and

deassertion of the PMD transmitter Enable pin (TXE).

011Reserved: Reserved for future use. Users are discouraged from using this transmit

mode. If selected, however, the transmitter will generate Quiet symbol pairs

(00000 00000).

100Master Transmit Mode (MTM): Transmission of Halt and Quiet symbol pairs

(00100 00000).

101Halt Transmit Mode (HTM): Transmission of Halt symbol pairs (00100 00100).

110Quiet Transmit Mode (QTM): Transmission of Quiet symbol pairs (00000 00000).

111Reserved: Reserved for future use. Users are discouraged from using this transmit

mode. If selected, however, the transmitter will generate Quiet symbol pairs

(00000 00000).

D3 TOSILS TRIGGER ON SILS: Trigger when SILS is received.

D4 TOMLS TRIGGER ON MLS: Trigger when MLS is received.

D5 TOHLS TRIGGER ON HLS: Trigger when HLS is received.

D6 TOQLS TRIGGER ON QLS (or NSD): Trigger when QLS is received.

D7 TONT TRIGGER ON Noise Threshold: Trigger when Noise Threshold is reached (Current Noise Registere0).

5.0 Registers (Continued)

5.39 TRIGGER TRANSITION CONFIGURATION REGISTER (TTCR)

The Trigger Transition Configuration Register holds the configuration switch setting to be loaded into the Configuration Register

(CR) when a trigger transition takes place. When scrubbing is enabled, scrubbing is performed for a period of time indicated by

the Scrub Timer Threshold Register (STTR).The register bit descriptions for the Configuration Register and, therefore, the

Trigger Transition Configuration Register are reprinted below.

ACCESS RULES

ADDRESS READ WRITE

27h Always Always

D7 D6 D5 D4 D3 D2 D1 D0

BIE AIE TRS1 TRS0 BIS1 BIS0 AIS1 AIS0

Bit Symbol Description

D0, D1 AIS0, AIS1 AÐINDICATE SELECTOR k0, 1l:The AÐIndicate Selector k0, 1lbits selects one of the four

Configuration Switch data buses for the AÐIndicate output port (AIP, AIC, AIDk7:0l).

AIS1 AIS0

0 0 PHY Invalid Bus

0 1 Receiver Bus

10A

Request Bus

11B

Request Bus

D2, D3 BIS0, BIS1 BÐINDICATE SELECTOR k0, 1l:The BÐIndicate Selector k0, 1lbits selects one of the four

Configuration Switch data buses for the BÐIndicate output port (BIP, BIC, BIDk7:0l).

BIS1 BIS0

0 0 PHY Invalid Bus

0 1 Receiver

10A

Request Bus

11B

Request Bus

Note: Even though this bit can be set and/or cleared in the DP83256 (for single path stations), it will not affect any I/Os since the

DP83256 does not offer a BÐIndicate port.

D4, D5 TRS0, TRS1 TRANSMIT REQUEST SELECTOR k0, 1l:The Transmit Request Selector k0, 1lbits selects one of

the four Configuration Switch data buses for the input to the Transmitter Block.

TRS1 TRS0

0 0 PHY Invalid Bus

0 1 Receiver Bus

10A

Request Bus

11B

Request Bus

Note: If the PLAYERadevice is in Active Transmit Mode (i.e. the Transmit Mode bits (TMk2:0l) of the Current Transmit State

symbols due to the Repeat Filter.

D6 AIE AÐINDICATE ENABLE:

0: Disables the AÐIndicate output port. The AÐIndicate port pins will be tri-stated when the port is

disabled.

1: Enables the AÐIndicate output port (AIP, AIC, AIDk7:0l).

D7 BIE BÐINDICATE ENABLE:

0: Disables the BÐIndicate output port. The BÐIndicate port pins will be tri-stated when the port is

disabled.

1: Enables the BÐIndicate output port (BIP, BIC, BIDk7:0l).

Note: Even though this bit can be set and/or cleared in the DP83256 (for single path stations), it will not affect any I/Os since the

DP83256 does not offer a BÐIndicate port.

5.0 Registers (Continued)

5.40 RESERVED REGISTERS 28H-3AH (RR28H-RR3AH)

These registers are reserved for future use.

DO NOT ACCESS THESE REGISTERS

ACCESS RULES

ADDRESS READ WRITE

28h–3Ah Always DO NOT WRITE

5.0 Registers (Continued)

5.41 CLOCK GENERATION MODULE REGISTER (CGMREG)

This register is used to enable or disable the 125 MHz ECL Transmit clock outputs. These outputs are not required for use in a

standard FDDI board implementation and are disabled by default to reduce high frequency noise.

These TXC outputs are included for support of alternate FDDI PMDs, such as unshielded twisted pair copper cable.

DO NOT WRITE TO RESERVED REGISTER BITS. Writes to reserved register bits could prevent proper device operation.

Therefore, read the register first, and then write it back with the non-reserved bits set to the desired value.

ACCESS RULES

ADDRESS READ WRITE

3Bh Always Always

D7 D6 D5 D4 D3 D2 D1 D0

RES RES FLTREN RES TXCE RES RES RES

Bit Symbol Description

D0-D2 RES RESERVED BITS: DO NOT CHANGE THE VALUE OF THESE BITS. Changes to reserved register bits could

prevent proper device operation.

D3 TXCE TRANSMIT CLOCK ENABLE: When bit is set to 1, 125 MHz ECL TXC outputs are enabled. When this bit is

reset to 0, TXC outputs are disabled. TXC outputs are disabled on reset.

Note: TXC clocks are only available on the 160-pin DP83257 PLAYERadevice.

D4 RES RESERVED BITS: DO NOT CHANGE THE VALUE OF THESE BITS. Changes to reserved register bits could

prevent proper device operation.

D5 FLTREN FILTER ENABLE: When bit is set to 1, the internal loop filter node is connected to the LPFLTR pin for

diagnostic viewing. This bit is reset to 0 by default, which disconnects the filter node from the LPFLTR pin.

Note: In normal operation this bit should be disabled (e0).

D6-D7 RES RESERVED BITS: DO NOT CHANGE THE VALUE OF THESE BITS. Changes to reserved register bits could

prevent proper device operation.

5.0 Registers (Continued)

5.42 ALTERNATE PMD REGISTER (APMDREG)

This register is used to enable or disable the Alternate PMD inputs and ouputs. These signals are not required for use in FDDI

board implementations that do not require a scrambler that is external to the PLAYERadevice. The actual interface consists of

the signal pairs RXCÐOUT, RXDÐOUT, RXCÐIN, and RXDÐIN.

The interface is disabled by default and should only be enabled if it is being used. Note that Long Internal Loopback should not

be used when the Alternate PMD Interface is enabled.

DO NOT WRITE TO RESERVED REGISTER BITS. Writes to reserved register bits could prevent proper device operation.

Therefore, read the register first, and then write it back with the non-reserved bits set to the desired value.

Note: The Alternate PMD Interface pins are only available on the 100-pin DP83256-AP and 160-pin DP83257 PLAYERadevices. The Alternate PMD Interface is

disabled on reset.

ACCESS RULES

ADDRESS READ WRITE

3Ch Always Always

D7 D6 D5 D4 D3 D2 D1 D0

RES RES RES RES APMDEN RES RES RES

Bit Symbol Description

D0–D2 RES RESERVED BITS: DO NOT CHANGE THE VALUE OF THESE BITS. Changes to reserved register bits could

prevent proper device operation.

D3 APMDEN ALTERNATE PMD ENABLE: When bit is set to 1, the Alternate PMD Interface is enabled. When this bit is

reset to 0, the Alternate PMD Interface is disabled.

The Alternate PMD Interface consists of the following extra ECL signal pairs

RXCÐOUT, RXDÐOUT, RXCÐIN, and RXDÐIN.

In some alternate PMD implementations it may also be necessary to use the 125 MHz Transmit Clock

signals (TXC). The TXC outputs must be separately enabled by the TXCE bit in the CGMREG register.

Note: The Alternate PMD Interface pins are only available on the 100-pin DP83256-AP and 160-pin DP83257 PLAYERadevices. The

Alternate PMD Interface is disabled on reset.

D4–D7 RES RESERVED BITS: DO NOT CHANGE THE VALUE OF THESE BITS. Changes to reserved register bits could

prevent proper device operation.

5.0 Registers (Continued)

5.43 GAIN REGISTER (GAINREG)

The Gain Register contains the settings for the CGM’s on-chip programmable loop filter. For optimal jitter performance on the

revision A and B PLAYERadevice’s Filter Position 4 should be used. The user should check that the IDR register is equal to

revision A or B (10h or 11h) before changing the filter setting as later revisions will default to the correct setting which may be a

different filter position number.

Pseudo Code Programming Example:

Care must be taken when changing the settings of the on-chip programmable loop filter. The filter should only be set to the

recommended value and the additional bits in the Gain Register must not be altered. Alteration of the reserved bits in the Gain

The following pseudo code outlines the proper procedure for setting the Gain Register loop filter settings to the correct value.

// Register names and constants are all in UPPERCASE

#define REV B 0x11

#define REV A 0x10

#define LOOP MASK 0x1F

#define NEW LOOP 0x40

if (IDR k4REV B) À

temp 4GAIN REG

temp 4temp & LOOP MASK

temp 4temp

NEW LOOP

GAIN REG 4temp

else ÀDo NothingÓ

ACCESS RULES

ADDRESS READ WRITE

3Dh Always Always

D7 D6 D5 D4 D3 D2 D1 D0

FILT2 FILT1 FILT0 RES RES RES RES RES

Bit Symbol Description

D0–D4 RES RESERVED: Do not alter these bits. The device may cease to operate properly if these bits are

changed.

D5–D7 FILT0,

FILT2

FILT1,

FILTER SELECTION k0, 1, 2l:The Filter Selection k0, 1, 2lbits select one of five on-chip CGM

loop filters.

Note: Filter combinations that are not specified or recommended should not be used and may result in non-optimal device

performance.

FILT2 FILT1 FILT0

1 1 0 FP0: Filter Position 0.

1 1 1 FP1: Filter Position 1.

0 0 0 FP2: Filter Position 2. This is the filter selected after reset on the

revision A and B PLAYERadevices.

0 0 1 FP3: Filter Position 3.

0 1 0 FP4: Filter Position 4. This is the recommended filter position for

the revision A and B PLAYERadevices.

5.0 Registers (Continued)

5.44 RESERVED REGISTERS 3EH-3FH (RR3EH-RR3FH)

These registers are reserved for future use.

DO NOT ACCESS THESE REGISTERS

ACCESS RULES

ADDRESS READ WRITE

3Eh–3Fh Always DO NOT WRITE

6.0 Signal Descriptions

6.1 DP83256VF PIN DESCRIPTIONS

The pin descriptions for the DP83256VF are divided into 5 functional interfaces: PMD Interface, PHY Port Interface, Control Bus

Interface, Clock Interface, and Miscellaneous Interface.

For a Pinout Summary list, refer to Table 8-1 and

Figure 8-1

, DP83256VF 100-Pin JEDEC Metric PQFP Pinout.

PMD INTERFACE

The PMD Interface consists of I/O signals used to connect the PLAYERadevice to the Physical Medium Dependant (PMD)

sublayer.

Symbol Pin ÝI/O Description

PMIDa39 I PMD Indicate Data: Differential, 100k ECL, 125 Mbps serial data input signals from the PMD receiver.

PMIDb38

PMRDa33 O PMD Request Data: Differential, 100k ECL, 125 Mbps serial data output signals to the PMD transmitter.

PMRDb32

SDa37 I Signal Detect: Differential 100k ECL input signals from the PMD receiver indicating that a signal is being

received by the PMD receiver.

SDb36

TEL 47 I PMD Transmitter Enable Level: A TTL input signal to select the PMD transmitter Enable (TXE) signal

level.

TXE 46 O PMD Transmitter Enable: A TTL output signal to enable/disable the PMD transmitter. The output level

of the TXE pin is determined by three parameters: the Transmit Enable (TE) bit in the Mode Register, the

TM2-TM0 bits in the Current Transmit State Register, and the input to the TEL pin. The following rules

summarize the output of the TXE pin:

1. If TEe0 and TELeGND, then TXEeVCC

2. If TEe0 and TELeVCC, then TXEeGND

3. If TEe1 and OTM and TELeGND, then TXEeVCC

4. If TEe1 and OTM and TELeVCC, then TXEeGND

5. If TEe1 and not OTM and TELeGND, then TXEeGND

6. If TEe1 and not OTM and TELeVCC, then TXEeVCC

6.0 Signal Descriptions (Continued)

PHY PORT INTERFACE

The PHY Port Interface consists of I/O signals used to connect the PLAYERadevice to the Media Access Control (MAC)

sublayer or other PLAYERadevice. The DP83256 Device has two PHY Port Interfaces. The AÐIndicate path from one PHY

Port Interface and the BÐRequest path from the second PHY Port Interface. Each path consists of an odd parity bit, a control

bit, and two 4-bit symbols.

Refer to section 3.3, the Configuration Switch, for more information.

Symbol Pin ÝI/O Description

AIP 6 O PHY Port A Indicate Parity: A TTL output signal representing odd parity for the 10-bit wide Port A

Indicate signals (AIP, AIC, and AIDk7:0l).

AIC 7 O PHY Port A Indicate Control: TTL output signal indicating that the two 4-bit symbols (AIDk7:4land

AIDk3:0l) are either control symbols (AICe1) or data symbols (AICe0).

AID7 8 O PHY Port A Indicate Data: TTL output signals representing the first 4-bit data/control symbol.

AID6 9 AID7 is the most significant bit and AID4 is the least significant bit of the first symbol.

AID5 10

AID4 13

AID3 14 O PHY Port A Indicate Data: TTL output signals representing the second 4-bit data/control symbol.

AID2 15 AID3 is the most significant bit and AID0 is the least significant bit of the second symbol.

AID1 16

AID0 17

BRP 70 I PHY Port B Request Parity: A TTL input signal representing odd parity for the 10-bit wide Port A

Request signals (BRP, BRC, and BRDk7:0l).

BRC 69 I PHY Port B Request Control: A TTL input signal indicating that the two 4-bit symbols

(BRDk7:4land BRDk3:0l) are either control symbols (BRCe1) or data symbols (BRCe0).

BRD7 68 I PHY Port B Request Data: TTL input signals representing the first 4-bit data/control symbol.

BRD6 67 BRD7 is the most significant bit and BRD4 is the least significant bit of the first symbol.

BRD5 66

BRD4 63

BRD3 62 I PHY Port B Request Data: TTL input signals representing the second 4-bit data/control symbol.

BRD2 61 BRD3 is the most significant bit and BRD0 is the least significant bit of the second symbol.

BRD1 60

BRD0 59

6.0 Signal Descriptions (Continued)

CONTROL BUS INTERFACE

The Control Bus Interface consists of I/O signals used to connect the PLAYERadevice to Station Management (SMT).

The Control Bus is an asynchronous interface between the PLAYERadevice and a general purpose microprocessor or other

controller. It provides access to 64 8-bit internal registers.

In the PLAYERadevice the Control Bus address range has been expanded by 1-bit to 6 bits of address space.

Symbol Pin ÝI/O Description

ECE 73 I Control Enable: An active-low, TTL, input signal which enables the Control Bus port for a read or write

cycle. R/EW, CBAk5:0l, CBP, and CBDk7:0lmust be valid at the time ECE is low.

R/EW72 IRead/EWrite: A TTL input signal which indicates a read Control Bus cycle(R/EWe1), or a write

Control Bus cycle (R/EWe0).

EACK 75 O EAcknowledge: An active low, TTL, open drain output signal which indicates the completion of a read

or write cycle. During a read cycle, CBDk7:0lare valid as long as EACK is low (EACKe0). During a

write cycle, a microprocessor must hold CBDk7:0lvalid until EACK becomes low. Once EACK is low,

it will remain low as long as ECE remains low (ECEe0).

EINT 74 O EInterrupt: An active low, open drain, TTL, output signal indicating that an interrupt condition has

occurred. The Interrupt Condition Register (ICR) should be read in order to find out the source of the

interrupt. Interrupts can be masked through the use of the Interrupt Condition Mask Register (ICMR).

CBA5 83 I Control Bus Address: TTL input signals used to select the address of the register to be read or written.

CBA4 82 CBA5 is the most significant bit (MSB) and CBA0 is the least significant bit (LSB) of the address signals.

CBA3 81

CBA2 80

CBA1 77

CBA0 76

CBP 96 I/O Control Bus Parity: A bidirectional, TTL signal representing odd parity for the Control Bus data

(CBDk7:0l).

During a read cycle, the signal is held valid by the PLAYERadevice as long as EACK is low.

During a write cycle, the signal must be valid when ECE is low, and must be held valid until EACK

becomes low. If incorrect parity is used during a write cycle, the PLAYERadevice will inhibit the write

cycle and set the Control Bus Data Parity Error (CPE) bit in the Interrupt Condition Register (ICR).

CBD7 95 I/O Control Bus Data: Bidirectional, TTL signals containing the data to be read from or written to a register.

CBD6 94 During a read cycle, the signal is held valid by the PLAYERadevice as long as EACK is low.

CBD5 93

During a write cycle, the signal must be valid when ECE is low, and must be held valid until EACK

CBD4 92

becomes low.

CBD3 91

CBD2 90

CBD1 89

CBD0 86

6.0 Signal Descriptions (Continued)

CLOCK INTERFACE

The Clock Interface consists of 12.5 MHz and 25 MHz clocks supplied by the PLAYERadevice as well as reference and

feedback inputs.

Symbol Pin ÝI/O Description

LBC1 4 O Local Byte Clock: TTL compatible, 12.5 MHz, 50% duty cycle clock outputs which are phase

locked to a crystal oscillator or reference signal. The PHÐSEL input determines whether the five

LBC2 3

phase outputs are phase offset by 8 ns or 16 ns.

LBC3 2

LBC4 1

LBC5 100

PHÐSEL 22 I Phase Select: TTL compatible input used to select eithera8nsor16nsphase offset between the 5

local byte clocks (LBC’s). The LBC’s are phase offset 8ns apart when PHÐSEL is at a logic LOW

level and 16 ns apart when at a logic HI level.

FBKÐIN 25 I Feedback Input: TTL compatible input for use as the PLL’s phase comparator feedback input to

close the Phase Locked Loop. This input is intended to be driven from one of the Local Byte Clocks

(LBC’s) from the same PLAYERadevice.

LSC 99 O Local Symbol Clock: TTL compatible 25 MHz output for driving the MACSI or BMAC devices. This

output’s negative phase transition is aligned with the LBC1 output transitions and has a 40% HI and

60% LOW duty cycle.

CLK16 5 O Clock 16/32: TTL compatible clock with a selectable frequency of approximately 15.625 MHz or

31.25 MHz. The frequency can be selected using the Clock Select (CLKSEL) bit of the Mode 2

Note: No glitches appear at the output when switching frequencies.

XTALÐIN 27 I External Crystal Oscillator Input: This input in conjunction with the XTALÐOUT output, is

designed for use of an external crystal oscillator network as the frequency reference for the clock

generation module’s internal VCO. A diagram of the required circuit, which includes only a 12.5 MHz

crystal and 2 loading capacitors, is shown in

Figure 3-19

This input is selected when the REFÐSEL input is at a logic LOW level. When not being used, this

input should be tied to ground.

XTALÐOUT 26 O External Crystal Oscillator Output: This output in conjunction with the XTALÐIN input, is designed

for use of an external crystal oscillator network as the frequency reference for the clock generation

module’s internal VCO. A diagram of the required circuit, which includes only a 12.5 MHz crystal and

2 loading capacitors, is shown in

Figure 3-19

REFÐIN 24 I Reference Input: TTL compatible input for use as the PLL’s phase comparator reference frequency.

This input is for use in dual attach station or concentrator configurations where there are multiple

PLAYERadevices at a given site requiring synchronization.

This input is selected when the REFÐSEL input is at a logic HI level.

REFÐSEL 23 I Reference Select: TTL compatible input which selects either the crystal oscillator inputs XTALÐIN

and XTALÐOUT or the REFÐIN inputs as the reference frequency inputs for the PLL.

The crystal oscillator inputs are selected when REFÐSEL is at a logic LOW level and the REFÐIN

input is selected as the reference when REFÐSEL is at a logic HI level.

LPFLTR 30 O Loop Filter: This is a diagnostic output that allows monitoring of the clock generation module’s filter

node. This output is disabled by default and does not need to be connected to any external device. It

can be enabled using the FLTREN bit of the Clock generation module register (CGMREG).

Note: In normal operation this pin should be disabled.

6.0 Signal Descriptions (Continued)

MISCELLANEOUS INTERFACE

The Miscellaneous Interface consist of a reset signal, user definable sense signals, and user definable enable signals.

Symbol Pin ÝI/O Description

ERST 71 I Reset: An active low, TTL, input signal which clears all registers. The signal must be kept asserted for a

minimum amount of time. Once the ERST signal is asserted, the PLAYERadevice should be allowed

the specified amount of time to reset internal logic. Note that bit zero of the Mode Register will be set to

zero (i.e. Stop Mode). See section 4.2, Stop Mode of Operation for more information

SP0 40 I User Definable Sense Pin 0: A TTL input signal from a user defined source. Sense Bit 0 (SB0) of the

User Definable Register (UDR) will be set to one if the signal is asserted for a minimum of 160 ns. Once

the asserted signal is latched, Sense Bit 0 can only be cleared through the Control Bus Interface, even if

the signal is deasserted. This ensures that the Control Bus Interface will record the source of events

which can cause interrupts.

SP1 42 I User Definable Sense Pin 1: A TTL input signal from a user defined source. Sense Bit 1 (SB1) of the

User Definable Register (UDR) will be set to one if the signal is asserted for a minimum of 160 ns. Once

the asserted signal is latched, Sense Bit 1 can only be cleared through the Control Bus Interface, even if

the signal is deasserted. This ensures that the Control Bus Interface will record the source of events

which can cause interrupts.

EP0 41 O User Definable Enable Pin 0: A TTL output signal allowing control of external logic through the Control

Bus Interface. EP0 is asserted/deasserted through Enable Bit 0 (EB0) of the User Definable Register

(UDR). When Enable Bit 0 is set to zero, EP0 is deasserted. When Enable Bit 0 is set to one, EP0 is

asserted.

EP1 43 O User Definable Enable Pin 1: A TTL output signal allowing control of external logic through the Control

Bus Interface. EP1 is asserted/deasserted through Enable Bit 1 (EB1) of the User Definable Register

(UDR). When Enable Bit 1 is set to zero, EP1 is deasserted. When Enable Bit 1 is set to one, EP1 is

asserted.

6.0 Signal Descriptions (Continued)

POWER AND GROUND

All power pins should be connected to a single a5V power supply using the recommended filtering. All ground pins should be

connected to a common 0V ground supply. Bypassing and filtering requirements are given in a separate User Information

Document.

Symbol Pin ÝI/O Description

VCCÐANALOG 20 Power: Positive 5V power supply for the PLAYERadevice’s CGM VCO.

GNDÐANALOG 21 Ground: Power supply return for the PLAYERadevice’s CGM VCO.

VCCÐCORE 88 Power: Positive 5V power supply for the core PLAYER section logic gates.

GNDÐCORE 87 Ground: Power supply return for the core PLAYER section logic gates.

VCCÐECL 31, Power: Positive 5V power supply for the PLAYERadevice’s ECL logic gates.

34,

44,

GNDÐECL 35, Ground: Power supply return for the PLAYERadevice’s ECL logic gates.

45,

VCCÐESD 28 Power: Positive 5V power supply for the PLAYERadevice’s ESD protection circuitry.

GNDÐESD 29 Ground: Power supply return for the PLAYERadevice’s ESD protection circuitry.

VCCÐIO 11, Power: Positive 5V power supply for the input/output buffers.

65,

79,

GNDÐIO 12, Ground: Power supply return for the input/output buffers.

64,

78,

SPECIAL CONNECT PINS

These are pins that have special connection requirements.

No Connect (N/C) pins should not be connected to anything. This means not to power, not to ground, and not to each other.

ReservedÐ0 (RESÐ0) pins must be connected to ground. These pins are not used to supply device power so they do not need

to be filtered or bypassed.

ReservedÐ1 (RESÐ1) pins must be connected to power. These pins are not used to supply device power so they do not need

to be filtered or bypassed.

Symbol Pin ÝI/O Description

N/C 49, 54 No Connect: Pins should not be connected to anything. This means not to power, not to ground, and

not to each other.

RESÐ0 18, 19, Reserved 0: Pins must be connected to ground. These pins are not used to supply device power so

they do not need to be filtered or bypassed.

48, 50,

51, 52,

53, 57,

58, 84

RESÐ185 Reserved 1: Pins must be connected to power. These pins are not used to supply device power so they

do not need to be filtered or bypassed.

6.0 Signal Descriptions (Continued)

6.2 DP83256VF-AP SIGNAL DESCRIPTIONS

The pin descriptions for the DP83256VF-AP are divided into five functional interfaces; PMD Interface, PHY Port Interface,

Control Bus Interface, Clock Interface, and Miscellaneous Interface.

For a Pinout Summary List, refer to Table 8-2 and

Figure 8-2

, DP83256VF-AP 100-Pin JEDEC Metric PQFP Pinout.

PMD INTERFACE

The PMD Interface consists of I/O signals used to connect the PLAYERadevice to the Physical Medium Dependant (PMD)

sublayer.

The DP83256VF-AP PLAYERadevice actually has two PMD interfaces. The Primary PMD Interface and the Alternate PMD

Interface.

The Primary PMD Interface should be used for all PMD implementations that do not require an external scrambler/descrambler

function, clock recovery function, or clock generation function, such as a Fiber Optic or Shielded Twisted Pair (SDDI) PMD. The

second, Alternate PMD Interface can be used to support Unshielded Twisted Pair (UTP) PMDs that require external scrambling,

with no external clock recovery or clock generation functions required.

Section 3.8 describes how the PLAYERacan be connected to the PMD and how the Alternate PMD can be enabled.

Note that when the Alternate PMD Interface is not being used, the pins that make up the interface must be connected in the

specific way described in the following Alternate PMD Interface table.

Primary PMD Interface

Symbol Pin ÝI/O Description

PMIDa42 I PMD Indicate Data: Differential, 100k ECL, 125 Mbps serial data input signals from the PMD Receiver

into the Clock Recovery Module (CRM) of the PLAYERa.

PMIDb41

PMRDa34 O PMD Request Data: Differential, 100k ECL, 125 Mbps serial data output signals to the PMD transmitter.

PMRDb33

SDa40 I Signal Detect: Differential 100k ECL input signals from the PMD receiver indicating that a signal is being

received by the PMD receiver.

SDb39

6.0 Signal Descriptions (Continued)

Alternate PMD Interface

Symbol Pin ÝI/O Description

PMIDa42 I PMD Indicate Data: Differential, 100k ECL, 125 Mbps serial data input signals from the PMD

Receiver into the Clock Recovery Module (CRM) of the PLAYERa.

PMIDb41

RXCÐOUTa36 O Recovered Clock Out: 125 MHz clock recovered by the Clock Recovery Module (CRM) from the

PMID data input.

RXCÐOUTb35

These signals are only active when the Alternate PMD Enable (APMDEN) bit of the Alternate PMD

When these two pins are not used they should be left Not Connected (N/C).

RXDÐOUTa52 O Recovered Data Out: 125 Mbps data recovered by the Clock Recovery Module (CRM) from the

PMID data input.

RXDÐOUTb51

These signals are only active when the Alternate PMD Enable (APMDEN) bit of the Alternate PMD

When these two pins are not used they should be left Not Connected (N/C).

RXCÐINa48 I Receive Clock In: Clock inputs to the Player section of the PLAYERa. These inputs must be

synchronized with the RXDÐIN inputs.

RXCÐINb47

These signals are only active when the Alternate PMD Enable (APMDEN) bit of the Alternate PMD

When these two pins are not used, pin 76 should be left Not Connected (N/C) and pin 75 should be

connected directly to ground (ReservedÐ0).

RXDÐINa50 I Receive Data In: Data inputs to the Player section of the PLAYERa. These inputs must be

synchronized with the RXCÐIN inputs.

RXDÐINb49

These signals are only active when the Alternate PMD Enable (APMDEN) bit of the Alternate PMD

When these two pins are not used, pin 78 should be left Not Connected (N/C) and pin 77 should be

connected directly to ground (ReservedÐ0).

PMRDa34 O PMD Request Data: Differential, 100k ECL, 125 Mbps serial data output signals to the PMD

transmitter.

PMRDb33

TXCa31 O Transmit Clock: 125 MHz, 100k ECL compatible differential outputs synchronized to the outgoing

PMRD data.

TXCb30

These signals can be enabled using the Transmit Clock Enable (TXCE) bit in the Clock Generation

Module Register (CGMREG).

When these two pins are not used they should be left Not Connected (N/C).

SDa40 I Signal Detect: Differential, 100k ECL, input signals from the PMD receiver indicating that a signal

is being received by the PMD receiver.

SDb39

6.0 Signal Descriptions (Continued)

PHY PORT INTERFACE

The PHY Port Interface consists of I/O signals used to connect the PLAYERadevice to the Media Access Control (MAC)

sublayer or other PLAYERadevice. The DP83256 Device has two PHY Port Interfaces. The AÐIndicate path from one PHY

Port Interface and the BÐRequest path from the second PHY Port Interface. Each path consists of an odd parity bit, a control

bit, and two 4-bit symbols.

Refer to section 3.3, the Configuration Switch, for more information.

Symbol Pin ÝI/O Description

AIP 6 O PHY Port A Indicate Parity: A TTL output signal representing odd parity for the 10-bit wide Port A

Indicate signals (AIP, AIC, and AIDk7:0l).

AIC 7 O PHY Port A Indicate Control: TTL output signal indicating that the two 4-bit symbols (AIDk7:4land

AIDk3:0l) are either control symbols (AICe1) or data symbols (AICe0).

AID7 8 O PHY Port A Indicate Data: TTL output signals representing the first 4-bit data/control symbol.

AID6 9 AID7 is the most significant bit and AID4 is the least significant bit of the first symbol.

AID5 10

AID4 13

AID3 14 O PHY Port A Indicate Data: TTL output signals representing the second 4-bit data/control symbol.

AID2 15 AID3 is the most significant bit and AID0 is the least significant bit of the second symbol.

AID1 16

AID0 17

BRP 70 I PHY Port B Request Parity: A TTL input signal representing odd parity for the 10-bit wide Port A

Request signals (BRP, BRC, and BRDk7:0l).

BRC 69 I PHY Port B Request Control: A TTL input signal indicating that the two 4-bit symbols (BRDk7:4land

BRDk3:0l) are either control symbols (BRCe1) or data symbols (BRCe0).

BRD7 68 I PHY Port B Request Data: TTL input signals representing the first 4-bit data/control symbol.

BRD6 67 BRD7 is the most significant bit and BRD4 is the least significant bit of the first symbol.

BRD5 66

BRD4 63

BRD3 62 I PHY Port B Request Data: TTL input signals representing the second 4-bit data/control symbol.

BRD2 61 BRD3 is the most significant bit and BRD0 is the least significant bit of the second symbol.

BRD1 60

BRD0 59

6.0 Signal Descriptions (Continued)

CONTROL BUS INTERFACE

The Control Bus Interface consists of I/O signals used to connect the PLAYERadevice to Station Management (SMT).

The Control Bus is an asynchronous interface between the PLAYERadevice and a general purpose microprocessor or other

controller. It provides access to 64 8-bit internal registers.

In the PLAYERadevice the Control Bus address range has been expanded by 1-bit to 6 bits of address space.

Symbol Pin ÝI/O Description

ECE 73 I Control Enable: An active-low, TTL, input signal which enables the Control Bus port for a read or write

cycle. R/EW, CBAk5:0l, CBP, and CBDk7:0lmust be valid at the time ECE is low.

R/EW72 IRead/EWrite: A TTL input signal which indicates a read Control Bus cycle (R/EWe1), or a write

Control Bus cycle (R/EWe0).

EACK 75 O EAcknowledge: An active low, TTL, open drain output signal which indicates the completion of a read

or write cycle. During a read cycle, CBDk7:0lare valid as long as EACK is low (EACKe0). During a

write cycle, a microprocessor must hold CBDk7:0lvalid until EACK becomes low. Once EACK is low,

it will remain low as long as ECE remains low (ECEe0).

EINT 74 O EInterrupt: An active low, open drain, TTL, output signal indicating that an interrupt condition has

occurred. The Interrupt Condition Register (ICR) should be read in order to find out the source of the

interrupt. Interrupts can be masked through the use of the Interrupt Condition Mask Register (ICMR).

CBA5 83 I Control Bus Address: TTL input signals used to select the address of the register to be read or written.

CBA4 82 CBA5 is the most significant bit (MSB) and CBA0 is the least significant bit (LSB) of the address signals.

CBA3 81

CBA2 80

CBA1 77

CBA0 76

CBP 96 I/O Control Bus Parity: A bidirectional, TTL signal representing odd parity for the Control Bus data

(CBDk7:0l).

During a read cycle, the signal is held valid by the PLAYERadevice as long as EACK is low.

During a write cycle, the signal must be valid when ECE is low, and must be held valid until EACK

becomes low. If incorrect parity is used during a write cycle, the PLAYERadevice will inhibit the write

cycle and set the Control Bus Data Parity Error (CPE) bit in the Interrupt Condition Register (ICR).

CBD7 95 I/O Control Bus Data: Bidirectional, TTL signals containing the data to be read from or written to a register.

CBD6 94 During a read cycle, the signal is held valid by the PLAYERadevice as long as EACK is low.

CBD5 93

During a write cycle, the signal must be valid when ECE is low, and must be held valid until EACK

CBD4 92

becomes low.

CBD3 91

CBD2 90

CBD1 89

CBD0 86

6.0 Signal Descriptions (Continued)

CLOCK INTERFACE

The Clock Interface consists of 12.5 MHz and 25 MHz clocks supplied by the PLAYERadevice as well as reference and

feedback inputs.

Symbol Pin ÝI/O Description

LBC1 4 O Local Byte Clock: TTL compatible, 12.5 MHz, 50% duty cycle clock outputs which are phase

locked to a crystal oscillator or reference signal. The PHÐSEL input determines whether the five

LBC2 3

phase outputs are phase offset by 8 ns or 16 ns.

LBC3 2

LBC4 1

LBC5 100

PHÐSEL 22 I Phase Select: TTL compatible input used to select eithera8nsor16nsphase offset between the 5

local byte clocks (LBC’s). The LBC’s are phase offset 8 ns apart when PHÐSEL is at a logic LOW

level and 16 ns apart when at a logic HI level.

FBKÐIN 25 I Feedback Input: TTL compatible input for use as the PLL’s phase comparator feedback input to

close the Phase Locked Loop. This input is intended to be driven from one of the Local Byte Clocks

(LBC’s) from the same PLAYERadevice.

LSC 99 O Local Symbol Clock: TTL compatible 25 MHz output for driving the MACSI or BMAC devices. This

output’s negative phase transition is aligned with the LBC1 output transitions and has a 40% HI and

60% LOW duty cycle.

CLK16 5 O Clock 16/32: TTL compatible clock with a selectable frequency of approximately 15.625 MHz or

31.25 MHz. The frequency can be selected using the Clock Select (CLKSEL) bit of the Mode 2

Note: No glitches appear at the output when switching frequencies.

XTALÐIN 27 I External Crystal Oscillator Input: This input in conjunction with the XTALÐOUT output, is

designed for use of an external crystal oscillator network as the frequency reference for the clock

generation module’s internal VCO. A diagram of the required circuit, which includes only a 12.5 MHz

crystal and 2 loading capacitors, is shown in

Figure 3-19

This input is selected when the REFÐSEL input is at a logic LOW level. When not being used, this

input should be tied to ground.

XTALÐOUT 26 O External Crystal Oscillator Output: This output in conjunction with the XTALÐIN input, is designed

for use of an external crystal oscillator network as the frequency reference for the clock generation

module’s internal VCO. A diagram of the required circuit, which includes only a 12.5 MHz crystal and

2 loading capacitors, is shown in

Figure 3-19

REFÐIN 24 I Reference Input: TTL compatible input for use as the PLL’s phase comparator reference frequency.

This input is for use in dual attach station or concentrator configurations where there are multiple

PLAYERadevices at a given site requiring synchronization.

This input is selected when the REFÐSEL input is at a logic HI level.

REFÐSEL 23 I Reference Select: TTL compatible input which selects either the crystal oscillator inputs XTALÐIN

and XTALÐOUT or the REFÐIN inputs as the reference frequency inputs for the PLL.

The crystal oscillator inputs are selected when REFÐSEL is at a logic LOW level and the REFÐIN

input is selected as the reference when REFÐSEL is at a logic HI level.

6.0 Signal Descriptions (Continued)

MISCELLANEOUS INTERFACE

The Miscellaneous Interface consist of a reset signal and user definable enable signals.

Symbol Pin ÝI/O Description

ERST 71 I Reset: An active low, TTL, input signal which clears all registers. The signal must be kept asserted for a

minimum amount of time. Once the ERST signal is asserted, the PLAYERadevice should be allowed

the specified amount of time to reset internal logic. Note that bit zero of the Mode Register will be set to

zero (i.e. Stop Mode). See section 4.2, Stop Mode of Operation for more information

EP0 41 O User Definable Enable Pin 0: A TTL output signal allowing control of external logic through the Control

Bus Interface. EP0 is asserted/deasserted through Enable Bit 0 (EB0) of the User Definable Register

(UDR). When Enable Bit 0 is set to zero, EP0 is deasserted. When Enable Bit 0 is set to one, EP0 is

asserted.

EP1 43 O User Definable Enable Pin 1: A TTL output signal allowing control of external logic through the Control

Bus Interface. EP1 is asserted/deasserted through Enable Bit 1 (EB1) of the User Definable Register

(UDR). When Enable Bit 1 is set to zero, EP1 is deasserted. When Enable Bit 1 is set to one, EP1 is

asserted.

100

6.0 Signal Descriptions (Continued)

POWER AND GROUND

All power pins should be connected to a single a5V power supply using the recommended filtering. All ground pins should be

connected to a common 0V ground supply. Bypassing and filtering requirements are given in a separate User Information

Document.

Symbol Pin ÝI/O Description

VCCÐANALOG 20 Power: Positive 5V power supply for the Clock Generation Module VCO.

GNDÐANALOG 21 Ground: Power supply return for the Clock Generation Module VCO.

VCCÐCORE 88 Power: Positive 5V power supply for the core PLAYER section logic gates.

GNDÐCORE 87 Ground: Power supply return for the core PLAYER section logic gates.

VCCÐECL 32, Power: Positive 5V power supply for the PLAYERadevice’s ECL logic gates.

37,

45,

GNDÐECL 38, Ground: Power supply return for the PLAYERadevice’s ECL logic gates.

46,

VCCÐESD 28 Power: Positive 5V power supply for the PLAYERadevice’s ESD protection circuitry.

GNDÐESD 29 Ground: Power supply return for the PLAYERadevice’s ESD protection circuitry.

VCCÐIO 11, Power: Positive 5V power supply for the input/output buffers.

65,

79,

GNDÐIO 12, Ground: Power supply return for the input/output buffers.

64,

78,

SPECIAL CONNECT PINS

These are pins that have special connection requirements.

No Connect (N/C) pins should not be connected to anything. This means not to power, not to ground, and not to each other.

ReservedÐ0 (RESÐ0) pins must be connected to ground. These pins are not used to supply device power so they do not need

to be filtered or bypassed.

ReservedÐ1 (RESÐ1) pins must be connected to power. These pins are not used to supply device power so they do not need

to be filtered or bypassed.

Symbol Pin ÝI/O Description

N/C 49, 53,

No Connect: Pins should not be connected to anything. This means not to power, not to ground, and

not to each other.

RESÐ0 18, 19, Reserved 0: Pins must be connected to ground. These pins are not used to supply device power so

they do not need to be filtered or bypassed.

48, 50,

51, 52,

57, 58,

RESÐ185 Reserved 1: Pins must be connected to power. These pins are not used to supply device power so they

do not need to be filtered or bypassed.

101

6.0 Signal Descriptions (Continued)

6.3 DP83257VF SIGNAL DESCRIPTIONS

The pin descriptions for the DP83257VF are divided into five functional interfaces; PMD Interface, PHY Port Interface, Control

Bus Interface, Clock Interface, and Miscellaneous Interface.

For a Pinout Summary List, refer to Table 8-3 and

Figure 8-3

, DP83257VF 160-Pin JEDEC Metric PQFP Pinout.

PMD INTERFACE

The PMD Interface consists of I/O signals used to connect the PLAYERadevice to the Physical Medium Dependant (PMD)

sublayer.

The DP83257 PLAYERadevice actually has two PMD interfaces. The Primary PMD Interface and the Alternate PMD Interface.

The Primary PMD Interface should be used for all PMD implementations that do not require an external scrambler/descrambler

function, clock recovery function, or clock generation function, such as a Fiber Optic or Shielded Twisted Pair (SDDI) PMD. The

second, Alternate PMD Interface can be used to support Unshielded Twisted Pair (UTP) PMDs that require external scrambling,

with no external clock recovery or clock generation functions required.

Section 3.8 describes how the PLAYERacan be connected to the PMD and how the Alternate PMD can be enabled.

Note that when the Alternate PMD Interface is not being used, the pins that make up the interface must be connected in the

specific way described in the following Alternate PMD Interface table.

Primary PMD Interface

Symbol Pin ÝI/O Description

PMIDa62 I PMD Indicate Data: Differential, 100k ECL, 125 Mbps serial data input signals from the PMD Receiver

into the Clock Recovery Module (CRM) of the PLAYERa.

PMIDb61

PMRDa54 O PMD Request Data: Differential, 100k ECL, 125 Mbps serial data output signals to the PMD transmitter.

PMRDb53

SDa60 I Signal Detect: Differential 100k ECL input signals from the PMD receiver indicating that a signal is being

received by the PMD receiver.

SDb59

TEL 74 I PMD Transmitter Enable Level: A TTL input signal to select the PMD transmitter Enable (TXE) signal

level.

TXE 73 O PMD Transmitter Enable: A TTL output signal to enable/disable the PMD transmitter. The output level

of the TXE pin is determined by three parameters: the Transmit Enable (TE) bit in the Mode Register, the

TM2–TM0 bits in the Current Transmit State Register, and the input to the TEL pin. The following rules

summarize the output of the TXE pin:

1. If TEe0 and TELeGND, then TXEeVCC

2. If TEe0 and TELeVCC, then TXEeGND

3. If TEe1 and OTM and TELeGND, then TXEeVCC

4. If TEe1 and OTM and TELeVCC, then TXEeGND

5. If TEe1 and not OTM and TELeGND, then TXEeGND

6. If TEe1 and not OTM and TELeVCC, then TXEeVCC

102

6.0 Signal Descriptions (Continued)

Alternate PMD Interface

Symbol Pin ÝI/O Description

PMIDa62 I PMD Indicate Data: Differential, 100k ECL, 125 Mbps serial data input signals from the PMD

Receiver into the Clock Recovery Module (CRM) of the PLAYERa.

PMIDb61

RXCÐOUTa56 O Recovered Clock Out: 125 MHz clock recovered by the Clock Recovery Module (CRM) from the

PMID data input.

RXCÐOUTb55

These signals are only active when the Alternate PMD Enable (APMDEN) bit of the Alternate PMD

When these two pins are not used they should be left Not Connected (N/C).

RXDÐOUTa83 O Recovered Data Out: 125 Mbps data recovered by the Clock Recovery Module (CRM) from the

PMID data input.

RXDÐOUTb82

These signals are only active when the Alternate PMD Enable (APMDEN) bit of the Alternate PMD

When these two pins are not used they should be left Not Connected (N/C).

RXCÐINa76 I Receive Clock In: Clock inputs to the Player section of the PLAYERa. These inputs must be

synchronized with the RXDÐIN inputs.

RXCÐINb75

These signals are only active when the Alternate PMD Enable (APMDEN) bit of the Alternate PMD

When these two pins are not used, pin 76 should be left Not Connected (N/C) and pin 75 should be

connected directly to ground (ReservedÐ0).

RXDÐINa78 I Receive Data In: Data inputs to the Player section of the PLAYERa. These inputs must be

synchronized with the RXCÐIN inputs.

RXDÐINb77

These signals are only active when the Alternate PMD Enable (APMDEN) bit of the Alternate PMD

When these two pins are not used, pin 78 should be left Not Connected (N/C) and pin 77 should be

connected directly to ground (ReservedÐ0).

PMRDa54 O PMD Request Data: Differential, 100k ECL, 125 Mbps serial data output signals to the PMD

transmitter.

PMRDb53

TXCa51 O Transmit Clock: 125 MHz, 100k ECL compatible differential outputs synchronized to the outgoing

PMRD data.

TXCb50

These signals can be enabled using the Transmit Clock Enable (TXCE) bit in the Clock Generation

Module Register (CGMREG).

When these two pins are not used they should be left Not Connected (N/C).

SDa60 I Signal Detect: Differential, 100k ECL, input signals from the PMD receiver indicating that a signal

is being received by the PMD receiver.

SDb59

TEL 74 I PMD Transmitter Enable Level: A TTL input signal to select the PMD transmitter Enable (TXE)

signal level.

TXE 73 O PMD Transmitter Enable: A TTL output signal to enable/disable the PMD transmitter. The output

level of the TXE pin is determined by three parameters: the Transmit Enable (TE) bit in the Mode

The following rules summarize the output of the TXE pin:

1. If TEe0 and TELeGND, then TXEeVCC

2. If TEe0 and TELeVCC, then TXEeGND

3. If TEe1 and OTM and TELeGND, then TXEeVCC

4. If TEe1 and OTM and TELeVCC, then TXEeGND

5. If TEe1 and not OTM and TELeGND, then TXEeGND

6. If TEe1 and not OTM and TELeVCC, then TXEeVCC

103

6.0 Signal Descriptions (Continued)

PHY PORT INTERFACE

The PHY Port Interface consists of I/O signals used to connect the PLAYERadevice to the Media Access Control (MAC)

sublayer or other PLAYERadevice. The DP83257 Device has two PHY Port Interfaces. The AÐRequest and AÐIndicate paths

from one PHY Port Interface and the BÐRequest and BÐIndicate paths from the second PHY Port Interface. Each path

consists of an odd parity bit, a control bit, and two 4-bit symbols.

Refer to section 3.3, the Configuration Switch, for more information.

Symbol Pin ÝI/O Description

AIP 6 O PHY Port A Indicate Parity: A TTL output signal representing odd parity for the 10-bit wide Port A

Indicate signals (AIP, AIC, and AIDk7:0l).

AIC 8 O PHY Port A Indicate Control: A TTL output signal indicating that the two 4-bit symbols (AIDk7:4land

AIDk3:0l) are either control symbols (AICe1) or data symbols (AICe0).

AID7 10 O PHY Port A Indicate Data: TTL output signals representing the first 4-bit data/control symbol.

AID6 12 AID7 is the most significant bit and AID4 is the least significant bit of the first symbol.

AID5 14

AID4 18

AID3 20 O PHY Port A Indicate Data: TTL output signals representing the second 4-bit data/control symbol.

AID2 22 AID3 is the most significant bit and AID0 is the least significant bit of the second symbol.

AID1 24

AID0 26

ARP 7 I PHY Port A Request Parity: A TTL input signal representing odd parity for the 10-bit wide Port A

Request signals (ARP, ARC, and ARDk7:0l).

ARC 9 I PHY Port A Request Control: A TTL input signal indicating that the two 4-bit symbols

(ARDk7:4land ARDk3:0l) are either control symbols (ARCe1) or data symbols (ARCe0).

ARD7 11 I PHY Port A Request Data: TTL input signals representing the first 4-bit data/control symbol.

ARD6 13 ARD7 is the most significant bit and ARD4 is the least significant bit of the first symbol.

ARD5 15

ARD4 19

ARD3 21 I PHY Port A Request Data: TTL input signals representing the second 4-bit data/control symbol.

ARD2 23 ARD3 is the most significant bit and ARD0 is the least significant bit of the second symbol.

ARD1 25

ARD0 27

BIP 114 O PHY Port B Indicate Parity: A TTL output signal representing odd parity for the 10-bit wide Port A

Indicate signals (BIP, BIC, and BIDk7:0l).

BIC 112 O PHY Port B Indicate Control: A TTL output signal indicating that the two 4-bit symbols (BIDk7:4land

BIDk3:0l) are either control symbols (BICe1) or data symbols (BICe0).

BID7 110 O PHY Port B Indicate Data: TTL output signals representing the first 4-bit data/control symbol.

BID6 108 BID7 is the most significant bit and BID4 is the least significant bit of the first symbol.

BID5 106

BID4 102

BID3 100 O PHY Port B Indicate Data: TTL output signals representing the second 4-bit data/control symbol.

BID2 98 BID3 is the most significant bit and BID0 is the least significant bit of the second symbol.

BID1 96

BID0 94

BRP 115 I PHY Port B Request Parity: A TTL input signal representing odd parity for the 10-bit wide Port A

Request signals (BRP, BRC, and BRDk7:0l).

BRC 113 I PHY Port B Request Control: A TTL input signal indicating that the two 4-bit symbols

(BRDk7:4land BRDk3:0l) are either control symbols (BRCe1) or data symbols (BRCe0).

104

6.0 Signal Descriptions (Continued)

Symbol Pin ÝI/O Description

BRD7 111 I PHY Port B Request Data: TTL input signals representing the first 4-bit data/control symbol.

BRD6 109 BRD7 is the most significant bit and BRD4 is the least significant bit of the first symbol.

BRD5 107

BRD4 103

BRD3 101 I PHY Port B Request Data: TTL input signals representing the second 4-bit data/control symbol.

BRD2 99 BRD3 is the most significant bit and BRD0 is the least significant bit of the second symbol.

BRD1 97

BRD0 95

105

6.0 Signal Descriptions (Continued)

CONTROL BUS INTERFACE

The Control Bus Interface consists of I/O signals used to connect the PLAYERadevice to Station Management (SMT).

The Control Bus is an asynchronous interface between the PLAYERadevice and a general purpose microprocessor or other

controller. It provides access to 64 8-bit internal registers.

In the PLAYERadevice the Control Bus address range has been expanded by 1-bit to 6 bits of address space.

Symbol Pin ÝI/O Description

ECE 118 I Control Enable: An active-low, TTL, input signal which enables the Control Bus port for a read or write

cycle. R/EW, CBAk5:0l, CBP, and CBDk7:0lmust be valid at the time ECE is low.

R/EW 117 I Read/EWrite: A TTL input signal which indicates a read Control Bus cycle (R/EWe1), or a write

Control Bus cycle (R/EWe0).

EACK 120 O EAcknowledge: An active low, TTL, open drain output signal which indicates the completion of a read

or write cycle. During a read cycle, CBDk7:0lare valid as long as EACK is low (EACKe0). During a

write cycle, a microprocessor must hold CBDk7:0lvalid until EACK becomes low. Once EACK is low,

it will remain low as long as ECE remains low (ECEe0).

EINT 119 O EInterrupt: An active low, open drain, TTL, output signal indicating that an interrupt condition has

occurred. The Interrupt Condition Register (ICR) should be read in order to find out the source of the

interrupt. Interrupts can be masked through the use of the Interrupt Condition Mask Register (ICMR).

CBA5 135 I Control Bus Address: TTL input signals used to select the address of the register to be read or written.

CBA4 134 CBA5 is the most significant bit (MSB) and CBA0 is the least significant bit (LSB) of the address signals.

CBA3 133

CBA2 132

CBA1 129

CBA0 128

CBP 148 I/O Control Bus Parity: A bidirectional, TTL signal representing odd parity for the Control Bus data

(CBDl7:0l).

During a read cycle, the signal is held valid by the PLAYERadevice as long as EACK is low.

During a write cycle, the signal must be valid when ECE is low, and must be held valid until EACK

becomes low. If incorrect parity is used during a write cycle, the PLAYERadevice will inhibit the write

cycle and set the Control Bus Data Parity Error (CPE) bit in the Interrupt Condition Register (ICR).

CBD7 147 I/O Control Bus Data: Bidirectional, TTL signals containing the data to be read from or written to a register.

CBD6 146 During a read cycle, the signal is held valid by the PLAYERadevice as long as EACK is low.

CBD5 145

During a write cycle, the signal must be valid when ECE is low, and must be held valid until EACK

CBD4 144

becomes low.

CBD3 143

CBD2 142

CBD1 141

CBD0 138

106

6.0 Signal Descriptions (Continued)

CLOCK INTERFACE

The Clock Interface consists of 12.5 MHz and 25 MHz clocks supplied by the PLAYERadevice as well as reference and

feedback inputs.

Symbol Pin ÝI/O Description

LBC1 4 O Local Byte Clock: TTL compatible, 12.5 MHz, 50% duty cycle clock outputs which are phase

locked to a crystal oscillator or reference signal. The PHÐSEL input determines whether the five

LBC2 3

phase outputs are phase offset by 8 ns or 16 ns.

LBC3 2

LBC4 1

LBC5 160

PHÐSEL 34 I Phase Select: TTL compatible input used to select eithera8nsor16nsphase offset between the 5

local byte clocks (LBC’s). The LBC’s are phase offset 8 ns apart when PHÐSEL is at a logic LOW

level and 16 ns apart when at a logic HI level.

FBKÐIN 37 I Feedback Input: TTL compatible input for use as the PLL’s phase comparator feedback input to

close the Phase Locked Loop. This input is intended to be driven from one of the Local Byte Clocks

(LBC’s) from the same PLAYERadevice.

LSC 159 O Local Symbol Clock: TTL compatible 25 MHz output for driving the MACSI or BMAC devices. This

output’s negative phase transition is aligned with the LBC1 output transitions and has a 40% HI and

60% LOW duty cycle.

CLK16 5 O Clock 16/32: TTL compatible clock with a selectable frequency of approximately 15.625 MHz or

31.25 MHz. The frequency can be selected using the Clock Select (CLKSEL) bit of the Mode 2

Note: No glitches appear at the output when switching frequencies.

XTALÐIN 46 I External Crystal Oscillator Input: This input in conjunction with the XTALÐOUT output, is

designed for use of an external crystal oscillator network as the frequency reference for the clock

generation module’s internal VCO. A diagram of the required circuit, which includes only a 12.5 MHz

crystal and 2 loading capacitors, is shown in

Figure 3-19

This input is selected when the REFÐSEL input is at a logic LOW level. When not being used, this

input should be tied to ground.

XTALÐOUT 45 O External Crystal Oscillator Output: This output in conjunction with the XTALÐIN input, is designed

for use of an external crystal oscillator network as the frequency reference for the clock generation

module’s internal VCO. A diagram of the required circuit, which includes only a 12.5 MHz crystal and

2 loading capacitors, is shown in

Figure 3-19

REFÐIN 36 I Reference Input: TTL compatible input for use as the PLL’s phase comparator reference frequency.

This input is for use in dual attach station or concentrator configurations where there are multiple

PLAYERadevices at a given site requiring synchronization.

This input is selected when the REFÐSEL input is at a logic HI level.

REFÐSEL 35 I Reference Select: TTL compatible input which selects either the crystal oscillator inputs XTALÐIN

and XTALÐOUT or the REFÐIN inputs as the reference frequency inputs for the PLL.

The crystal oscillator inputs are selected when REFÐSEL is at a logic LOW level and the REFÐIN

input is selected as the reference when REFÐSEL is at a logic HI level.

LPFLTR 49 O Loop Filter: This is a diagnostic output that allows monitoring of the clock generation module’s filter

node. This output is disabled by default and does not need to be connected to any external device. It

can be enabled using the FLTREN bit of the Clock generation module register (CGMREG).

Note: In normal operation this pin should be disabled.

107

6.0 Signal Descriptions (Continued)

MISCELLANEOUS INTERFACE

The Miscellaneous Interface consist of a reset signal, user definable sense signals, and user definable enable signals.

Symbol Pin ÝI/O Description

ERST 116 I Reset: An active low, TTL, input signal which clears all registers. The signal must be kept asserted for a

minimum amount of time. Once the ERST signal is asserted, the PLAYERadevice should be allowed

the specified amount of time to reset internal logic. Note that bit zero of the Mode Register will be set to

zero (i.e. Stop Mode). See section 4.2, Stop Mode of Operation for more information

SP0 63 I User Definable Sense Pin 0: A TTL input signal from a user defined source. Sense Bit 0 (SB0) of the

User Definable Register (UDR) will be set to one if the signal is asserted for a minimum of 160 ns. Once

the asserted signal is latched, Sense Bit 0 can only be cleared through the Control Bus Interface, even if

the signal is deasserted. This ensures that the Control Bus Interface will record the source of events

which can cause interrupts.

SP1 65 I User Definable Sense Pin 1: A TTL input signal from a user defined source. Sense Bit 1 (SB1) of the

User Definable Register (UDR) will be set to one if the signal is asserted for a minimum of 160 ns. Once

the asserted signal is latched, Sense Bit 1 can only be cleared through the Control Bus Interface, even if

the signal is deasserted. This ensures that the Control Bus Interface will record the source of events

which can cause interrupts.

SP2 67 I User Definable Sense Pin 2: A TTL input signal from a user defined source. Sense Bit 2 (SB2) of the

User Definable Register (UDR) will be set to one if the signal is asserted for a minimum of 160 ns. Once

the asserted signal is latched, Sense Bit 2 can only be cleared through the Control Bus Interface, even if

the signal is deasserted. This ensures that the Control Bus Interface will record the source of events

which can cause interrupts.

EP0 64 O User Definable Enable Pin 0: A TTL output signal allowing control of external logic through the Control

Bus Interface. EP0 is asserted/deasserted through Enable Bit 0 (EB0) of the User Definable Register

(UDR). When Enable Bit 0 is set to zero, EP0 is deasserted. When Enable Bit 0 is set to one, EP0 is

asserted.

EP1 66 O User Definable Enable Pin 1: A TTL output signal allowing control of external logic through the Control

Bus Interface. EP1 is asserted/deasserted through Enable Bit 1 (EB1) of the User Definable Register

(UDR). When Enable Bit 1 is set to zero, EP1 is deasserted. When Enable Bit 1 is set to one, EP1 is

asserted.

EP2 68 O User Definable Enable Pin 2: A TTL output signal allowing control of external logic through the Control

Bus Interface. EP2 is asserted/deasserted through Enable Bit 2 (EB2) of the User Definable Register

(UDR). When Enable Bit 2 is set to zero, EP2 is deasserted. When Enable Bit 2 is set to one, EP2 is

asserted.

CS 69 I Cascade Start: A TTL input signal used to synchronize cascaded PLAYERadevices in point-to-point

applications.

The signal is asserted when all of the cascaded PLAYERadevices have the Cascade Mode (CM) bit of

the Mode Register (MR) set to one, and all of the Cascade Ready (CR) pins of the cascaded PLAYERa

devices have been released.

When Cascade Mode is not being used, this input should be tied to Ground.

For further information, refer to section 4.4, Cascade Mode of Operation.

CR 70 O Cascade Ready: An Open Drain output signal used to synchronize cascaded PLAYERadevices in

point-to-point applications.

The signal is released (i.e. an Open Drain line is released) when all the cascaded PLAYERadevices

have the Cascade Mode (CM) bit of the Mode Register (MR) is set to one and a JK symbol pair has been

received.

When Cascade Mode is not being used, this input should be left Not Connected (N/C).

For further information, refer to section 4.4, Cascade Mode of Operation.

108

6.0 Signal Descriptions (Continued)

POWER AND GROUND

All power pins should be connected to a single a5V power supply using the recommended filtering. All ground pins should be

connected to a common 0V ground supply. Bypassing and filtering requirements are given in a separate User Information

Document.

Symbol Pin ÝI/O Description

VCCÐANALOG 32 Power: Positive 5V power supply for the PLAYERadevice’s CGM VCO.

GNDÐANALOG 33 Ground: Power supply return for the PLAYERadevice’s CGM VCO.

VCCÐCORE 140 Power: Positive 5V power supply for the core PLAYER logic gates.

GNDÐCORE 139 Ground: Power supply return for the core PLAYER logic gates.

VCCÐECL 52, 57, Power: Positive 5V power supply for the PLAYERadevice’s ECL logic gates.

71, 89

GNDÐECL 58, 72, Ground: Power supply return for the PLAYERadevice’s ECL logic gates.

VCCÐESD 47 Power: Positive 5V power supply for the PLAYERadevice’s ESD protection circuitry.

GNDÐESD 48 Ground: Power supply return for the PLAYERadevice’s ESD protection circuitry.

VCCÐIO 16, 105, Power: Positive 5V power supply for the input/output buffers.

131, 158

GNDÐIO 17, 104, Ground: Power supply return for the input/output buffers.

130, 157

SPECIAL CONNECT PINS

These are pins that have special connection requirements.

No Connect (N/C) pins should not be connected to anything. This means not to power, not to ground, and not to each other.

ReservedÐ0 (RESÐ0) pins must be connected to ground. These pins are not used to supply device power so they do not need

to be filtered or bypassed.

ReservedÐ1 (RESÐ1) pins must be connected to power. These pins are not used to supply device power so they do not need

to be filtered or bypassed.

Symbol Pin ÝI/O Description

N/C 38, 39, No Connect: Pins should not be connected to anything. This means not to power, not

to ground, and not to each other.

40, 41, 42, 43, 44,

79,

80, 81, 87,

121, 122, 123, 124, 125,

126, 127,

149,

150, 151, 152, 153,154,

155, 156

RESÐ0 28, 29, Reserved 0: Pins must be connected to ground. These pins are not used to supply

device power so they do not need to be filtered or bypassed.

30, 31,

84, 85, 86,

90, 91, 92, 93,

136

RESÐ1 137 Reserved 1: Pins must be connected to power. These pins are not used to supply

device power so they do not need to be filtered or bypassed.

109

7.0 Electrical Characteristics

7.1 ABSOLUTE MAXIMUM RATINGS

Symbol Parameter Conditions Min Typ Max Units

VCC Supply Voltage b0.5 7.0 V

DCIN Input Voltage b0.5 VCC a0.5 V

DCOUT Output Voltage b0.5 VCC a0.5 V

VCCÐESD to other VCC

Maximum Voltage 0.3 V

Differential

Storage Temperature b65 150 §C

ECL Signal Output Current b50 mA

ESD Protection 2000 V

7.2 RECOMMENDED OPERATING CONDITIONS

Symbol Parameter Conditions Min Typ Max Units

VCC Supply Voltage 4.75 5.25 V

TAOperating Temperature 0 70 §C

FREF Reference Input Frequency 12.5–50 ppm 12.5 12.5 a50 ppm MHz

7.3 RECOMMENDED EXTERNAL COMPONENTS

Symbol Parameter Conditions Min Typ Max Units

XTAL Crystal Specifications

Center Frequency 12.5 MHz

Frequency Calibration b10 10 ppm

Frequency Stability Over Temperature b10 10 ppm

Aging Less Than b5 5 ppm

Recommended Power Supply Bypassing Capacitor Value 0.1 mF

Note: Capacitors should be placed between each supply pair as close to the

device as possible.

7.4 DC ELECTRICAL CHARACTERISTICS

The DC characteristics are specified over the Recommended Operating Conditions, unless otherwise specified.

DC Electrical Characteristics for All TTL-Compatible Inputs

The following signals are covered: PHY Port Request Signals (ARD, ARC, ARP, BRD, BRC, BRP), Phase Select (PHÐSEL),

Reference Select (REFÐSEL), Sense Pins (SP), Cascade Start (CS), PMD Transmitter Enable Level (TEL), Device Reset

(ERST), and Control Bus Interface Inputs (R/EW, ECE, CBA).

Symbol Parameter Conditions Min Typ Max Units

VIH Input High Voltage 2.0 V

VIL Input Low Voltage 0.8 V

VIC Input Clamp Voltage IIN eb

18 mA b1.5 V

IIL Input Low Current VIN eGND b10 mA

IIH Input High Current VIN eVCC a10 mA

110

7.0 Electrical Characteristics (Continued)

DC Electrical Characteristics for All TTL-Compatible Non-TRI-STATE Outputs

The following signals are covered: Clock 16/32 (CLK16), Enable Pins (EP), and PMD Transmitter Enable (TXE).

Symbol Parameter Conditions Min Typ Max Units

VOH Output High Voltage IOH eb

2mA V

CC b0.5 V

VOL Output Low Voltage IOL e4 mA 0.5 V

DC Electrical Characteristics for All TTL-Compatible TRI-STATE Outputs

The following signals are covered: PHY Port Indicate Signals (AID, AIC, AIP, BID, BIC, BIP).

Symbol Parameter Conditions Min Typ Max Units

VOH Output High Voltage IOH eb

2mA V

CC b0.5 V

VOL Output Low Voltage IOL e4 mA 0.5 V

IOZ3 TRI-STATE Leakage VOUT eVCC 60 mA

(Note 1)

IOZ4 TRI-STATE Leakage VOUT eVGND b500 mA

(Note 1)

Note 1: Output buffer has a p-channel pullup device.

DC Electrical Characteristics for All TTL-Compatible Input/Outputs

The following signals are covered: Control Bus Interface I/O (CBD, CBP).

Symbol Parameter Conditions Min Typ Max Units

VIH Input High Voltage 2.0 V

VIL Input Low Voltage 0.8 V

VIC Input Clamp Voltage IIN eb

18 mA b1.5 V

IIL Input Low Current VIN eGND b10 mA

IIH Input High Current VIN eVCC a10 mA

VOH Output High Voltage IOH eb

2mA V

CC b0.5 V

VOL Output Low Voltage IOL e4 mA 0.5 V

IOZ1 TRI-STATE Leakage VOUT eVCC 10 mA

IOZ2 TRI-STATE Leakage VOUT eVGND b10 mA

111

7.0 Electrical Characteristics (Continued)

DC Electrical Characteristics for All FDDI Clock Outputs

The following signals are covered: Local Byte Clocks (LBC1–LBC5), and Local Symbol Clock (LSC).

These outputs are designed to drive capacitive loads from 20 pF to 60 pF.

Symbol Parameter Conditions Min Typ Max Units

VOH Output High Voltage IOH eb

400 mAV

CC b2V

OL Output Low Voltage IOL e8 mA 0.5 V

DC Electrical Characteristics for All Clock Reference Inputs

The following signals are covered: Reference In (REFÐIN) and Feedback In (FBKÐIN).

Symbol Parameter Conditions Min Typ Max Units

VIH Input High Voltage 2.0 V

VIL Input Low Voltage 0.8 V

VIC Input Clamp Voltage IIN eb

18 mA b1.5 V

IIL Input Low Current VIN eGND b10 mA

IIH Input High Current VIN eVCC a10 mA

DC Electrical Characteristics for Crystal Inputs and Outputs

The following signals are covered: Crystal In (XTALÐIN) and Crystal Out (XTALÐOUT).

Symbol Parameter Conditions Min Typ Max Units

IOL Output Low Current VOUT e1V 4 mA

(Note A)

IOH Output High Current VOUT eVCC b1V b4mA

(Note A)

Small Signal Gain XTALÐIN e100 mV 45

Centered about VTH

(Note A)

VTH Input Threshold (Note A) 2.2 V

Voltage

XTALÐIN to (Note A) 7.0 ns

XTALÐOUT Delay

Output Impedance (Note A) 270 X

Internal Resistor (Note A) 10 kX

Variation

Note A: This parameter is presented as a typical value to provide enough information to design an appropriate crystal network.

DC Electrical Characteristics for All Open Drain Outputs

The following signals are covered: Interrupt (EINT), Acknowledge (EACK), and Cascade Ready (CR).

Symbol Parameter Conditions Min Typ Max Units

VOL Output Low Voltage IOL e8 mA 0.5 V

IOZ TRI-STATE Leakage VOUT eVCC 10 mA

112

7.0 Electrical Characteristics (Continued)

DC Electrical Characteristics for All 100K ECL Compatible Inputs

The following signals are covered: PMD Indicate Data (PMID), Receive Clock In (RXCÐIN), Receive Data In (RXDÐIN), and

Signal Detect (SD).

Symbol Parameter Conditions Min Typ Max Units

VDIFF Input Voltage Differential (Note 1) 150 mV

VCM Common Mode Voltage VDIFF e300 mV VCC b2.0 VCC b0.5 V

(Notes 1, 2)

IIN Input Current VIN eVCC or GND b200 200 mA

Note 1: Both inputs of each differential pair are tested together. These specifications guarantee that the inputs are compatible with standard 100K ECL voltage

level outputs.

Note 2: VCM is measured from the crossover point of the 300 mV differential test input.

DC Electrical Characteristics for 100K ECL Compatible Outputs

The following signals are covered: PMD Request Data (PMRD) and Transmit Clock (TXC).

Symbol Parameter Conditions Min Typ Max Units

VOH Output High Voltage VIL eVCC b1.810 VCC b1.025 VCC b0.880 V

VOL Output Low Voltage VIH eVCC b0.880 VCC b1.810 VCC b1.620 V

DC Electrical Characteristics for Alternate PMD ECL Outputs

The following signals are covered: Receive Clock Out (RXCÐOUT) and Receive Data Out (RXDÐOUT).

Symbol Parameter Conditions Min Typ Max Units

VOH Output High Voltage VIL eVCC b1.810 VCC b1.155 VCC b0.880 V

VOL Output Low Voltage VIH eVCC b0.880 VCC b1.810 VCC b1.550 V

(Note 3)

Note 3: It is recommended that RXCÐOUTaand RXCÐOUTbalways be used together as a differential pair. It is recommended that RXDÐOUTaand

RXDÐOUTbalways be used together as a differential pair.

Supply Current Electrical Characteristics

Symbol Parameter Conditions Min Typ Max Units

ICC Total Supply LBC1 e12.5 MHz 350*mA

ECLÐICC ECL Supply Current LBC1 e12.5 MHz 200*mA

ANALOGÐICC ANALOG Supply Current LBC1 e12.5 MHz 20*mA

*Note: The PLAYERadevice has multiple pairs of differential ECL outputs that need to be terminated. The additional current needed for this termination is not

included in the PLAYERa’s total supply current, but can be calculated as follows:

VOHÐmax eVCC b0.88V

VOLÐmax eVCC b1.62V

Since the outputs are differential, the average output level is VCC b1.25V. The test load per output is 50Xat VCC b2V, therefore the external load current

through the 50Xresistor is:

ILOAD e[(VCC b1.25) b(VCC b2)]/50

e0.015A

e15 mA

As a result, the termination for each pair of active ECL outputs typically consumes 30 mA, time averaged.

113

7.0 Electrical Characteristics (Continued)

7.5 AC ELECTRICAL CHARACTERISTICS

The AC Electrical characteristics are specified over the Recommended Operating Conditions, unless otherwise specified.

AC Characteristics for the Control Bus Interface

The following signals are covered: Control Bus Interface (R/EW, ECE, EINT, EACK, CBA, CBD, and CBP).

Symbol Descriptions Min Max Units

T1 CE Setup to LBC 15 ns

T2 LBC Period 80 ns

T3 LBC1 to ACK Low 45 ns

T4 CE Low to ACK Low 290 540 ns

T5 LBC1 Low to CBD(7– 0) and CBP Valid 60 ns

T6 LBC1 to CBD(7– 0) and CBP Active 5 ns

T7 CE Low to CBD(7– 0) and CBP Active 225 475 ns

T8 CE Low to CBD(7– 0) and CBP Valid 265 515 ns

T9 LBC Pulse Width High 35 45 ns

T10 LBC Pulse Width Low 35 45 ns

T11 CE High to ACK High 45 ns

T12 R/W, CBA(5–0), CBD(7 –0) and CBP Setup to CE Low 5 ns

T13 CE High to R/W, CBA(5–0), CBD(7 –0) and CBP Hold Time 0 ns

T14 R/W, CBA(5–0), CBD(7 –0) and CBP to LBC1 Setup Time 20 ns

T15 ACK Low to CE High Lead Time 0 ns

T16 CE Minimum Pulse Width High 20 ns

T17 CE High to CBD(7–0) and CBP TRI-STATE 55 ns

T18 ACK High to CE Low 0 ns

T19 CBD(7–0) Valid to ACK Low Setup 20 ns

T20a LBC1 to R/W Hold Time 10 ns

T20b LBC1 to CBA Hold Time 10 ns

T20c LBC1 to CBD and CBP Hold Time 20 ns

T21 LBC1 to INT Low 55 ns

T22 LBC1 to EP Change 5 25 ns

Asynchronous Definitions

T4 (min) T1 a(3 *T2) aT3

T4 (max) T1 a(6 *T2) aT3

T7 (min) T1 a(2 *T2) aT6

T7 (max) T1 a(5 *T2) aT6

T8 (min) T1 a(2 *T2) aT9 aT5

T8 (max) T1 a(5 *T2) aT9 aT5

Note: Min/Max numbers are based on T2 e80 ns and T9 eT10 e40 ns.

114

7.0 Electrical Characteristics (Continued)

TL/F/11708– 29

FIGURE 7-1. Asynchronous Control Bus Write Cycle Timing

TL/F/11708– 30

FIGURE 7-2. Asynchronous Control Bus Read Cycle Timing

115

7.0 Electrical Characteristics (Continued)

TL/F/11708– 31

FIGURE 7-3. Control Bus Synchronous Writes

TL/F/11708– 32

FIGURE 7-4. Control Bus Synchronous Reads

TL/F/11708– 50

FIGURE 7-5. Control Bus Interrupt Timing

116

7.0 Electrical Characteristics (Continued)

AC Characteristics for the Clock Interface Signals (Timing and Relationships)

Symbol Parameter Conditions Min Typ Max Units

TPhase1 LBC1–LBC2 Timing PHÐSEL eLOW 5.0 8 11.0 ns

TPhase2 LBC1–LBC3 Timing PHÐSEL eLOW 13.0 16 19.0 ns

TPhase3 LBC1–LBC4 Timing PHÐSEL eLOW 21.0 24 27.0 ns

TPhase4 LBC1–LBC5 Timing PHÐSEL eLOW 29.0 32 35.0 ns

TPhase1 LBC1–LBC2 Timing PHÐSEL eHIGH 45.0 48 51.0 ns

TPhase2 LBC1–LBC3 Timing PHÐSEL eHIGH 13.0 16 19.0 ns

TPhase3 LBC1–LBC4 Timing PHÐSEL eHIGH 61.0 64 67.0 ns

TPhase4 LBC1–LBC5 Timing PHÐSEL eHIGH 29.0 32 35.0 ns

TPhase5 LBC5 Rising- PHÐSEL eLOW or 5.0 8 12.0 ns

LBC1 Falling Timing PHÐSEL eHIGH

T23 LSC Falling to LBC1 (Note 1) b3a6ns

T24 REFÐIN to FBKÐIN In Lock b2a2ns

Note 1: LSC loading must always be less than or equal to LBC1 loading.

TL/F/11708– 33

FIGURE 7-6. Clock Signal Relationships

117

7.0 Electrical Characteristics (Continued)

TL/F/11708– 51

FIGURE 7-7. Typical Clock Signal Relationships Based on Phase Select (PHÐSEL) Setting

118

7.0 Electrical Characteristics (Continued)

AC Characteristics for the Clock Interface Signals (Periods and Pulse Widths)

Symbol Parameter Conditions Min Typ Max Units

T2 LBC Period 80 ns

T9 LBC Pulse Width High 35 45 ns

T10 LBC Pulse Width Low 35 45 ns

T25 LSC Pulse Width High 12 19 ns

T26 LSC Pulse Width Low 21 28 ns

T27 CLK16 Period MODE2.CLKSEL e064 ns

T28 CLK16 Pulse Width MODE2.CLKSEL e027 32 37 ns

(Note 1)

T27 CLK16 Period MODE2.CLKSEL e132 ns

T28 CLK16 Pulse Width MODE2.CLKSEL e111 16 21 ns

(Note 1)

T29 REFÐIN Pulse Width High 35 45 ns

Note 1: This parameter is not tested, but is assured by correlation with characterization data.

TL/F/11708– 34

FIGURE 7-8. Clock Pulse Widths

AC Characteristics for Port A Interface and Port B Interface

The following signals are covered: PHY Port A (AID, AIP, AIC, ARD, ARP, ARC) and PHY Port B (BID, BIP, BIC, BRD, BRP,

BRC).

Symbol Parameter Conditions Min Typ Max Units

T30 LBC1 to Indicate Data Changes from 70 ns

TRI-STATE to Valid Data

T31 LBC1 to Indicate Data Changes from 70 ns

Active to TRI-STATE

T32 LBC1 to Indicate Data Sustain 9 ns

T33 LBC1 to Valid Indicate Data 45 ns

T34 Request Data to LBC1 Setup Time 15 ns

T35 Request Data to LBC1 Hold Time 3 ns

TL/F/11708– 35

FIGURE 7-9. PHY Port Interface Timing

119

7.0 Electrical Characteristics (Continued)

AC Characteristics for the PMD Interface

The following signals are covered: PMD Indicate Data (PMID), Signal Detect (SD), and PMD Request Data (PMRD).

Symbol Parameter Conditions Min Typ Max Units

T36 PMIDgto PMRDgLatency Looped Back through 5 LBC

Configuration Switch. Cycles

LBC1 e12.5 MHz

In Lock

(Note 1)

T37 SD Minimum Pulse Width 120 ns

T38 PMRD Rise Time (Note 2) 1.5 ns

T39 PMRD Fall Time (Note 2) 1.5 ns

Note 1: This only applies when the Alternate PMD Interface is disabled, APMDREG.APMDEN e0.

Note 2: This parameter is not tested, but is assured by correlation with characterization data.

TL/F/11708– 36

FIGURE 7-10. Primary PMD Timing Diagrams

120

7.0 Electrical Characteristics (Continued)

AC Characteristics for the Alternate PMD Interface

The following input signals are covered: PMD Indicate Data (PMID), Signal Detect (SD), Receive Data In (RXDÐIN), Receive

Clock In (RXCÐIN).

The following output signals are covered: PMD Request Data (PMRD), Transmit Clock (TXC), Recovered Data Out

(RXDÐOUT), Recovered Clock Out (RXCÐOUT).

Note: The Alternate PMD Interface is only available on the 160 pin DP83257 PLAYERaDevice and the 100 pin DP83256-AP Device. The Transmit Clock is

enabled by the CGMREG.TXCE bit. The rest of the Alternate PMD Interface is enabled by the APMDREG.APMDEN bit.

Symbol Parameter Conditions Min Typ Max Units

T40 RXCÐOUTato RXDÐOUTgChange Time 1.0 5.0 ns

T41 PMIDgto RXDÐOUT Latency In Lock 16 ns

T42 RXDÐINgto RXCÐINaSetup Time 4.0 ns

T43 RXDÐINgto RXCÐINaHold Time 0.5 ns

T44 TXCato PMRDgChange Time 4.0 7.0 ns

T42 SD Minimum Pulse Width 120 ns

T45 RXCÐOUTgPulse Width High (Note 1) 3.5 4.5 ns

T46 RXCÐOUTgRise Time (Note 1) 1.5 ns

T47 RXCÐOUTgFall Time (Note 1) 1.5 ns

T48 RXDÐOUTgRise Time (Note 1) 1.5 ns

T49 RXDÐOUTgFall Time (Note 1) 1.5 ns

T50 TXCgPulse Width High (Note 1) 3.5 4.5 ns

T51 TXCgRise Time (Note 1) 1.5 ns

T52 TXCgFall Time (Note 1) 1.5 ns

T38 PMRD Rise Time (Note 1) 1.5 ns

T39 PMRD Fall Time (Note 1) 1.5 ns

Note 1: This parameter is not tested, but is assured by correlation with characterization data.

TL/F/11708– 52

FIGURE 7-11. ECL Rise and Fall Times

121

7.0 Electrical Characteristics (Continued)

TL/F/11708– 53

FIGURE 7-12. Alternate PMD Timing Diagrams

122

7.0 Electrical Characteristics (Continued)

AC Characteristics for the PMD Interface Inputs (ANSI Specifications)

The following input signals are covered: PMD Indicate Data (PMID), Receive Data In (RXDÐIN), Receive Clock In (RXCÐIN).

Note: The Alternate PMD Interface is only available on the 160 pin DP83257 PLAYERaDevice and the 100 pin DP83256-AP Device. The Transmit Clock is

enabled by the CGMREG.TXCE bit. The rest of the Alternate PMD Interface is enabled by the APMDREG.APMDEN bit.

All comments in square brackets are section references to the ANSI documents where these specifications can be found.

Symbol Parameter Conditions Min Typ Max Units

T53 CRM Window Recognition Region [PMD E.2]b33ns

(PMID Inputs)

T54 PMID Receive Clock Tolerance [PHY 5.2.4]b100 100 ppm

(Lock Acquisition Range)

T55 Receive Clock Acquisition Time From 1st Data 100 ms

and SD Active

[PHY 5.2.6]

T56 Receive Clock Acquisition Time From Line State 15 ms

Change

[PHY 5.2.6]

TL/F/11708– 54

TL/F/11708– 55

FIGURE 7-13. Alternate PMD Input Timing DiagramsÐANSI Specifications

123

7.0 Electrical Characteristics (Continued)

AC Characteristics for the PMD Interface Outputs (ANSI Specifications)

The following output signals are covered: PMD Request Data (PMRD), Transmit Clock (TXC), Recovered Data Out

(RXDÐOUT), Recovered Clock Out (RXCÐOUT).

Note: The Alternate PMD Interface is only available on the 160 pin DP83257 PLAYERaDevice and the 100 pin DP83256-AP Device. The Transmit Clock is

enabled by the CGMREG.TXCE bit. The rest of the Alternate PMD Interface is enabled by the APMDREG.APMDEN bit.

Comments in square brackets are section references to the ANSI documents where these specifications can be found.

Symbol Parameter Conditions Min Typ Max Units

T57 PMRD Total Transmit Jitter (Note 1) 0.72 ns p-p

[Duty Cycle Distortion (DCD)a[PMD 8.1]

Data Dependent Jitter (DDJ)a

Random Jitter (RJ)]

T58 Total Recovered Clock (RXCÐOUT) Jitter (Note 1) 2.5 ns p-p

[Static Alignment Error Accuracy (SAE)a[PMD E.2]

Clock Data Dependent Jitter (CÐDDJ)a

Random Jitter (CÐRJ)]

Note 1: This parameter is not tested, but is assured through characterization data and periodic testing of sample units.

124

7.0 Electrical Characteristics (Continued)

AC Characteristics for User Definable Pins

The following signals are covered: Sense Pins (SP).

For Enable Pins (EP) timing see AC Characteristics for the Control Bus Interface.

Symbol Parameter Conditions Min Typ Max Units

T59 SP Minimum Pulse Width 120 ns

TL/F/11708– 56

FIGURE 7-14. SP Minimum Pulse Width

AC Characteristics for Miscellaneous Interface

The following signal is covered: Reset (ERST).

Symbol Parameter Conditions Min Typ Max Units

T60 Minimum Reset (ERST) Pulse Width 300 ns

T61 Maximum Power Up Reset Cycle Duration (Notes 1, 2) 10 ms

T62 Maximum Hardware Reset (ERST) Cycle Duration 0.5 ms

Note 1: This parameter is not tested, but is assured by correlation with characterization data.

Note 2: User must wait this long before trying to access the device after power up. It is recommended that a Hardware Reset be used sometime after the Power Up

Reset cycle is complete to insure proper device reset.

TL/F/11708– 57

FIGURE 7-15. Reset Timing

125

7.0 Electrical Characteristics (Continued)

AC TEST CIRCUITS

TL/F/11708– 37

Note: S1is closed for TPZL and TPLZ

S2is closed for TPZH and TPHZ

S1and S2are open otherwise

FIGURE 7-16. Switching Test Circuit for All TRI-STATE Output Signals

TL/F/11708– 38

FIGURE 7-17. Switching Test Circuit for All TTL Output Signals

TL/F/11708– 39

FIGURE 7-18. Switching Test Circuit for All Open Drain Output Signals (INT, ACK, and CR)

TL/F/11708– 40

FIGURE 7-19. Switching Test Circuit for All ECL Input and Output Signals

126

7.0 Electrical Characteristics (Continued)

TEST WAVEFORMS

TL/F/11708– 41

FIGURE 7-20. ECL Output Test Waveform

TL/F/11708– 42

Note: All CMOS Inputs and outputs are TTL compatible.

FIGURE 7-21. TTL Output Test Waveform

TL/F/11708– 43

FIGURE 7-22. TRI-STATE Output Test Waveform

127

8.0 Connection Diagrams

8.1 DP83256VF CONNECTION DIAGRAM

For a Pinout Summary List, refer to Table 8-1.

TL/F/11708– 44

FIGURE 8-1. DP83256VF 100-Pin JEDEC Metric PQFP Pinout

128

8.0 Connection Diagrams (Continued)

TABLE 8-1. DP83256 100-Pin PQFP Pinout Summary

Pin No. Signal Name Symbol I/O Pin Type

1 Local Byte Clock 4 LBC4 O TTL

2 Local Byte Clock 3 LBC3 O TTL

3 Local Byte Clock 2 LBC2 O TTL

4 Local Byte Clock 1 LBC1 O TTL

5 Clock 16/32 CLK16 O TTL

6 PHY Port A Indicate Parity AIP O TTL

7 PHY Port A Indicate Control AIC O TTL

8 PHY Port A Indicate Datak7lAID7 O TTL

9 PHY Port A Indicate Datak6lAID6 O TTL

10 PHY Port A Indicate Datak5lAID5 O TTL

11 I/O Power VCCÐIO a5V

12 I/O Ground GNDÐIO a0V

13 PHY Port A Indicate Datak4lAID4 O TTL

14 PHY Port A Indicate Datak3lAID3 O TTL

15 PHY Port A Indicate Datak2lAID2 O TTL

16 PHY Port A Indicate Datak1lAID1 O TTL

17 PHY Port A Indicate Datak0lAID0 O TTL

18 ReservedÐ0 RESÐ0a0V

19 ReservedÐ0 RESÐ0a0V

20 ANALOG Power VCCÐANALOG a5V

21 ANALOG Ground GNDÐANALOG a0V

22 Phase Select PHÐSEL I TTL

23 Reference Select REFÐSEL I TTL

24 Reference Input REFÐIN I TTL

25 Feedback Input FBKÐIN I TTL

26 Crystal Output XTALÐOUT O

27 Crystal Input XTALÐIN I

28 ESD Power VCCÐESD a5V

29 ESD Ground GNDÐESD a0V

30 Loop Filter LPFLTR O

31 ECL Power VCCÐECL a5V

32 PMD Request Data bPMRDbO ECL

33 PMD Request Data aPMRDaO ECL

34 ECL Power VCCÐECL a5V

35 ECL Ground GNDÐECL a0V

36 Signal Detect bSDbI ECL

37 Signal Detect aSDaI ECL

38 PMD Indicate Data bPMIDbI ECL

129

8.0 Connection Diagrams (Continued)

TABLE 8-1. DP83256 100-Pin PQFP Pinout Summary (Continued)

Pin No. Signal Name Symbol I/O Pin Type

39 PMD Indicate Data aPMIDaI ECL

40 Sense Pin 0 SP0 I TTL

41 Enable Pin 0 EP0 O TTL

42 Sense Pin 1 SP1 I TTL

43 Enable Pin 1 EP1 O TTL

44 ECL Power VCCÐECL a5V

45 ECL Ground GNDÐECL a0V

46 PMD Transmitter Enable TXE O TTL

47 PMD Transmitter Enable Level TEL I TTL

48 ReservedÐ0 RESÐ0a0V

49 No Connect N/C

50 ReservedÐ0 RESÐ0a0V

51 ReservedÐ0 RESÐ0a0V

52 ReservedÐ0 RESÐ0a0V

53 ReservedÐ0 RESÐ0a0V

54 No Connect N/C

55 ECL Ground GNDÐECL a0V

56 ECL Power VCCÐECL a5V

57 ReservedÐ0 RESÐ0a0V

58 ReservedÐ0 RESÐ0a0V

59 PHY Port B Request Datak0lBRD0 I TTL

60 PHY Port B Request Datak1lBRD1 I TTL

61 PHY Port B Request Datak2lBRD2 I TTL

62 PHY Port B Request Datak3lBRD3 I TTL

63 PHY Port B Request Datak4lBRD4 I TTL

64 I/O Ground GNDÐIO a0V

65 I/O Power VCCÐIO a5V

66 PHY Port B Request Datak5lBRD5 I TTL

67 PHY Port B Request Datak6lBRD6 I TTL

68 PHY Port B Request Datak7lBRD7 I TTL

69 PHY Port B Request Control BRC I TTL

70 PHY Port B Request Parity BRP O TTL

71 EDevice Reset ERST I TTL

72 Read/EWrite R/EW I TTL

73 Chip Enable ECE I TTL

74 EInterrupt EINT O Open Drain

75 EAcknowledge EACK O Open Drain

76 Control Bus Addressk0lCBA0 I TTL

130

8.0 Connection Diagrams (Continued)

TABLE 8-1. DP83256 100-Pin PQFP Pinout Summary (Continued)

Pin No. Signal Name Symbol I/O Pin Type

77 Control Bus Addressk1lCBA1 I TTL

78 I/O Logic Ground GNDÐIO a0V

79 I/O Logic Power VCCÐIO a5V

80 Control Bus Addressk2lCBA2 I TTL

81 Control Bus Addressk3lCBA3 I TTL

82 Control Bus Addressk4lCBA4 I TTL

83 Control Bus Addressk5lCBA5 I TTL

84 ReservedÐ0 RESÐ0a0V

85 ReservedÐ1 RESÐ1a5V

86 Control Bus Datak0lCBD0 I/O TTL

87 Core Ground GNDÐCORE a0V

88 Core Power VCCÐCORE a5V

89 Control Bus Datak1lCBD1 I/O TTL

90 Control Bus Datak2lCBD2 I/O TTL

91 Control Bus Datak3lCBD3 I/O TTL

92 Control Bus Datak4lCBD4 I/O TTL

93 Control Bus Datak5lCBD5 I/O TTL

94 Control Bus Datak6lCBD6 I/O TTL

95 Control Bus Datak7lCBD7 I/O TTL

96 Control Bus Data Parity CBP I/O TTL

97 I/O Ground GNDÐIO a0V

98 I/O Power VCCÐIO a5V

99 Local Symbol Clock LSC O TTL

100 Local Byte Clock5 LBC5 O TTL

131

8.0 Connection Diagrams (Continued)

8.2 DP83256VF-AP CONNECTION DIAGRAM

For a Pinout Summary List, refer to Table 8-2.

TL/F/11708– 58

FIGURE 8-2. DP83256VF-AP 100-Pin JEDEC Metric PQFP Pinout

132

8.0 Connection Diagrams (Continued)

TABLE 8-2. DP83256VF-AP 100-Pin PQFP Pinout Summary

Pin No. Signal Name Symbol I/O Pin Type

1 Local Byte Clock 4 LBC4 O TTL

2 Local Byte Clock 3 LBC3 O TTL

3 Local Byte Clock 2 LBC2 O TTL

4 Local Byte Clock 1 LBC1 O TTL

5 Clock 16/32 CLK16 O TTL

6 PHY Port A Indicate Parity AIP O TTL

7 PHY Port A Indicate Control AIC O TTL

8 PHY Port A Indicate Datak7lAID7 O TTL

9 PHY Port A Indicate Datak6lAID6 O TTL

10 PHY Port A Indicate Datak5lAID5 O TTL

11 I/O Power VCCÐIO a5V

12 I/O Ground GNDÐIO a0V

13 PHY Port A Indicate Datak4lAID4 O TTL

14 PHY Port A Indicate Datak3lAID3 O TTL

15 PHY Port A Indicate Datak2lAID2 O TTL

16 PHY Port A Indicate Datak1lAID1 O TTL

17 PHY Port A Indicate Datak0lAID0 O TTL

18 ReservedÐ0 RESÐ0a0V

19 ReservedÐ0 RESÐ0a0V

20 ANALOG Power VCCÐANALOG a5V

21 ANALOG Ground GNDÐANALOG a0V

22 Phase Select PHÐSEL I TTL

23 Reference Select REFÐSEL I TTL

24 Reference Input REFÐIN I TTL

25 Feedback Input FBKÐIN I TTL

26 Crystal Output XTALÐOUT O

27 Crystal Input XTALÐIN I

28 ESD Power VCCÐESD a5V

29 ESD Ground GNDÐESD a0V

30 Transmit ClockbTXCbO ECL

31 Transmit ClockaTXCaO ECL

32 ECL Power VCCÐECL a5V

33 PMD Request Data bPMRDbO ECL

34 PMD Request Data aPMRDaO ECL

35 Receive Clock OutbRXCÐOUTbO ECL

36 Receive Clock OutaRXCÐOUTaO ECL

37 ECL Power VCCÐECL a5V

38 ECL Ground GNDÐECL a0V

133

8.0 Connection Diagrams (Continued)

TABLE 8-2. DP83256VF-AP 100-Pin PQFP Pinout Summary (Continued)

Pin No. Signal Name Symbol I/O Pin Type

39 Signal DetectbSDbI ECL

40 Signal DetectaSDaI ECL

41 PMD Indicate DatabPMIDbI ECL

42 PMD Indicate DateaPMIDaI ECL

43 Enable Pin 0 EP0 O TTL

44 Enable Pin 1 EP1 O TTL

45 ECL Power VCCÐECL a5V

46 ECL Ground GNDÐECL a0V

47 Receive Clock InbRXCÐINbI ECL

48 Receive Clock InaRXCÐINaI ECL

49 Receive Data InbRXDÐINbI ECL

50 Receive Data InaRXDÐINaI ECL

51 Receive Data OutbRXDÐOUTbO ECL

52 Receive Data OutaRXDÐOUTaO ECL

53 No Connect N/C

54 No Connect N/C

55 ECL Ground GNDÐECL a0V

56 ECL Power VCCÐECL a5V

57 ReservedÐ0 RESÐ0a0V

58 ReservedÐ0 RESÐ0a0V

59 PHY Port B Request Datak0lBRD0 I TTL

60 PHY Port B Request Datak1lBRD1 I TTL

61 PHY Port B Request Datak2lBRD2 I TTL

62 PHY Port B Request Datak3lBRD3 I TTL

63 PHY Port B Request Datak4lBRD4 I TTL

64 I/O Ground GNDÐIO a0V

65 I/O Power VCCÐIO a5V

66 PHY Port B Request Datak5lBRD5 I TTL

67 PHY Port B Request Datak6lBRD6 I TTL

68 PHY Port B Request Datak7lBRD7 I TTL

69 PHY Port B Request Control BRC I TTL

70 PHY Port B Request Parity BRP O TTL

71 EDevice Reset ERST I TTL

72 Read/EWrite R/EW I TTL

73 Chip Enable ECE I TTL

74 EInterrupt EINT O Open Drain

75 EAcknowledge EACK O Open Drain

76 Control Bus Addressk0lCBA0 I TTL

134

8.0 Connection Diagrams (Continued)

TABLE 8-2. DP83256VF-AP 100-Pin PQFP Pinout Summary (Continued)

Pin No. Signal Name Symbol I/O Pin Type

77 Control Bus Addressk1lCBA1 I TTL

78 I/O Logic Ground GNDÐIO a0V

79 I/O Logic Power VCCÐIO a5V

80 Control Bus Addressk2lCBA2 I TTL

81 Control Bus Addressk3lCBA3 I TTL

82 Control Bus Addressk4lCBA4 I TTL

83 Control Bus Addressk5lCBA5 I TTL

84 ReservedÐ0 RESÐ0a0V

85 ReservedÐ1 RESÐ1a5V

86 Control Bus Datak0lCBD0 I/O TTL

87 Core Ground GNDÐCORE a0V

88 Core Power VCCÐCORE a5V

89 Control Bus Datak1lCBD1 I/O TTL

90 Control Bus Datak2lCBD2 I/O TTL

91 Control Bus Datak3lCBD3 I/O TTL

92 Control Bus Datak4lCBD4 I/O TTL

93 Control Bus Datak5lCBD5 I/O TTL

94 Control Bus Datak6lCBD6 I/O TTL

95 Control Bus Datak7lCBD7 I/O TTL

96 Control Bus Data Parity CBP I/O TTL

97 I/O Ground GNDÐIO a0V

98 I/O Power VCCÐIO a5V

99 Local Symbol Clock LSC O TTL

100 Local Byte Clock5 LBC5 O TTL

135

8.0 Connection Diagrams (Continued)

8.3 DP83257VF CONNECTION DIAGRAM

For a Pinout Summary List, refer to Table 8-3.

TL/F/11708– 45

FIGURE 8-3. DP83257VF 160-Pin JEDEC Metric PQFP Pinout

136

8.0 Connection Diagrams (Continued)

TABLE 8-3. DP83257 160-Pin PQFP Pinout Summary

Pin No. Signal Name Symbol I/O Pin Type

1 Local Byte Clock 4 LBC4 O TTL

2 Local Byte Clock 3 LBC3 O TTL

3 Local Byte Clock 2 LBC2 O TTL

4 Local Byte Clock 1 LBC1 O TTL

5 Clock 16/32 CLK16 O TTL

6 PHY Port A Indicate Parity AIP O TTL

7 PHY Port A Request Parity ARP I TTL

8 PHY Port A Indicate Control AIC O TTL

9 PHY Port A Request Control ARC I TTL

10 PHY Port A Indicate Datak7lAID7 O TTL

11 PHY Port A Request Datak7lARD7 I TTL

12 PHY Port A Indicate Datak6lAID6 O TTL

13 PHY Port A Request Datak6lARD6 I TTL

14 PHY Port A Indicate Datak5lAID5 O TTL

15 PHY Port A Request Datak5lARD5 I TTL

16 I/O Power VCCÐIO a5V

17 I/O Ground GNDÐIO a0V

18 PHY Port A Indicate Datak4lAID4 O TTL

19 PHY Port A Request Datak4lARD4 I TTL

20 PHY Port A Indicate Datak3lAID3 O TTL

21 PHY Port A Request Datak3lARD3 I TTL

22 PHY Port A Indicate Datak2lAID2 O TTL

23 PHY Port A Request Datak2lARD2 I TTL

24 PHY Port A Indicate Datak1lAID1 O TTL

25 PHY Port A Request Datak1lARD1 I TTL

26 PHY Port A Indicate Datak0lAID0 O TTL

27 PHY Port A Request Datak0lARD0 I TTL

28 ReservedÐ0 RESÐ0a0V

29 ReservedÐ0 RESÐ0a0V

30 ReservedÐ0 RESÐ0a0V

31 ReservedÐ0 RESÐ0a0V

32 ANALOG Power VCCÐANALOG a5V

33 ANALOG Ground GNDÐANALOG a0V

34 Phase Select PHÐSEL I TTL

35 Reference Select REFÐSEL I TTL

36 Reference Input REFÐIN I TTL

37 Feedback Input FBKÐIN I TTL

38 No Connect N/C

137

8.0 Connection Diagrams (Continued)

TABLE 8-3. DP83257 160-Pin PQFP Pinout Summary (Continued)

Pin No. Signal Name Symbol I/O Pin Type

39 No Connect N/C

40 No Connect N/C

41 No Connect N/C

42 No Connect N/C

43 No Connect N/C

44 No Connect N/C

45 Crystal Output XTALÐOUT O

46 Crystal Input XTALÐIN I

47 ESD Power VCCÐESD a5V

48 ESD Ground GNDÐESD a0V

49 Loop Filter LPFLTR O

50 Transmit ClockbTXCbO ECL

51 Transmit ClockaTXCaO ECL

52 ECL Power VCCÐECL a5V

53 PMD Request DatabPMRDbO ECL

54 PMD Request Data aPMRDaO ECL

55 Receive Clock OutbRXCÐOUTbO ECL

56 Receive Clock OutaRXCÐOUTaO ECL

57 ECL Power VCCÐECL a5V

58 ECL Ground GNDÐECL a0V

59 Signal DetectbSDbI ECL

60 Signal DetectaSDaI ECL

61 PMD Indicate DatabPMIDbI ECL

62 PMD Indicate DataaPMIDaI ECL

63 Sense Pin 0 SP0 I TTL

64 Enable Pin 0 EP0 O TTL

65 Sense Pin 1 SP1 I TTL

66 Enable Pin 1 EP1 O TTL

67 Sense Pin 2 SP2 I TTL

68 Enable Pin 2 EP2 O TTL

69 Cascade Start CS I TTL

70 Cascade Ready CR O Open Drain

71 ECL Power VCCÐECL a5V

72 ECL Ground GNDÐECL a0V

73 PMD Transmitter Enable TXE O TTL

74 PMD Transmitter Enable Level TEL I TTL

75 Receive Clock InbRXCÐINbI ECL

76 Receive Clock InaRXCÐINaI ECL

138

8.0 Connection Diagrams (Continued)

TABLE 8-3. DP83257 160-Pin PQFP Pinout Summary (Continued)

Pin No. Signal Name Symbol I/O Pin Type

77 Receive Data InbRXDÐINbI ECL

78 Receive Data InaRXDÐINaI ECL

79 No Connect N/C

80 No Connect N/C

81 No Connect N/C

82 Receive Data OutbRXDÐOUTbO ECL

83 Receive Data OutaRXDÐOUTaO ECL

84 ReservedÐ0 RESÐ0a0V

85 ReservedÐ0 RESÐ0a0V

86 ReservedÐ0 RESÐ0a0V

87 No Connect N/C

88 ECL Ground GNDÐECL a0V

89 ECL Power VCCÐECL a5V

90 ReservedÐ0 RESÐ0a0V

91 ReservedÐ0 RESÐ0a0V

92 ReservedÐ0 RESÐ0a0V

93 ReservedÐ0 RESÐ0a0V

94 PHY Port B Indicate Datak0lBID0 O TTL

95 PHY Port B Request Datak0lBRD0 I TTL

96 PHY Port B Indicate Datak1lBID1 O TTL

97 PHY Port B Request Datak1lBRD1 I TTL

98 PHY Port B Indicate Datak2lBID2 O TTL

99 PHY Port B Request Datak2lBRD2 I TTL

100 PHY Port B Indicate Datak3lBID3 O TTL

101 PHY Port B Request Datak3lBRD3 I TTL

102 PHY Port B Indicate Datak4lBID4 O TTL

103 PHY Port B Request Datak4lBRD4 I TTL

104 I/O Ground GNDÐIO a0V

105 I/O Power VCCÐIO a5V

106 PHY Port B Indicate Datak5lBID5 O TTL

107 PHY Port B Request Datak5lBRD5 I TTL

108 PHY Port B Indicate Datak6lBID6 O TTL

109 PHY Port B Request Datak6lBRD6 I TTL

110 PHY Port B Indicate Datak7lBID7 O TTL

111 PHY Port B Request Datak7lBRD7 I TTL

112 PHY Port B Indicate Control BIC O TTL

113 PHY Port B Request Control BRC I TTL

114 PHY Port B Indicate Parity BIP O TTL

139

8.0 Connection Diagrams (Continued)

TABLE 8-3. DP83257 160-Pin PQFP Pinout Summary (Continued)

Pin No. Signal Name Symbol I/O Pin Type

115 PHY Port B Request Parity BRP I TTL

116 EDevice Reset ERST I TTL

117 Read/EWrite R/EW I TTL

118 Chip Enable ECE I TTL

119 EInterrupt EINT O Open Drain

120 EAcknowledge EACK O Open Drain

121 No Connect N/C

122 No Connect N/C

123 No Connect N/C

124 No Connect N/C

125 No Connect N/C

126 No Connect N/C

127 No Connect N/C

128 Control Bus Addressk0lCBA0 I TTL

129 Control Bus Addressk1lCBA1 I TTL

130 I/O Logic Ground GNDÐIO a0V

131 I/O Logic Power VCCÐIO a5V

132 Control Bus Addressk2lCBA2 I TTL

133 Control Bus Addressk3lCBA3 I TTL

134 Control Bus Addressk4lCBA4 I TTL

135 Control Bus Addressk5lCBA5 I TTL

136 ReservedÐ0 RESÐ0a0V

137 ReservedÐ1 RESÐ1a5V

138 Control Bus Datak0lCBD0 I/O TTL

139 Core Ground GNDÐCORE a0V

140 Core Power VCCÐCORE a5V

141 Control Bus Datak1lCBD1 I/O TTL

142 Control Bus Datak2lCBD2 I/O TTL

143 Control Bus Datak3lCBD3 I/O TTL

144 Control Bus Datak4lCBD4 I/O TTL

145 Control Bus Datak5lCBD5 I/O TTL

146 Control Bus Datak6lCBD6 I/O TTL

147 Control Bus Datak7lCBD7 I/O TTL

148 Control Bus Data Parity CBP I/O TTL

149 No Connect N/C

150 No Connect N/C

151 No Connect N/C

140

8.0 Connection Diagrams (Continued)

TABLE 8-3. DP83257 160-Pin PQFP Pinout Summary (Continued)

Pin No. Signal Name Symbol I/O Pin Type

152 No Connect N/C

153 No Connect N/C

154 No Connect N/C

155 No Connect N/C

156 No Connect N/C

157 I/O Ground GNDÐIO a0V

158 I/O Power VCCÐIO a5V

159 Local Symbol Clock LSC O TTL

160 Local Byte Clock5 LBC5 O TTL

141

9.0 Package Information

The information contained in this section describes the two packages used for the PLAYERadevice.

Land pattern information is provided to assist in surface mount layout using each of the available PLAYERadevice packages.

Mechanical drawings of each of the packages are also provided.

9.1 LAND PATTERNS

TL/F/11708– 46

FIGURE 9-1. Layout Land Patterns

TABLE 9-1. Layout Land Pattern Dimensions

Device A (mm) B (mm) P (mm) X (mm)

DP83256VF and DP83256VF-AP 14.60 18.45 0.50 0.35

14mm x 14mm x 2.0mm

100-lead JEDEC FPQFP

DP83257VF 28.90 33.40 0.65 0.45

28mm x 28mm x 3.42mm

160-lead JEDEC MQFP

9.2 MECHANICAL DRAWINGS

The following two pages contain the mechanical drawings for each of the available PLAYERadevice packages.

142

Physical Dimensions millimeters

Plastic Quad Flatpak (VJU)

Order Number DP83256VF and DP83256VF-AP

NS Package Number VJU100A

143

DP83256/56-AP/57 PLAYERaDevice (FDDI Physical Layer Controller)

Physical Dimensions millimeters (Continued)

Plastic Quad Flatpak (V)

Order Number DP83257VF

NS Package Number VUL160A

LIFE SUPPORT POLICY

NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT

DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT OF NATIONAL

SEMICONDUCTOR CORPORATION. As used herein:

1. Life support devices or systems are devices or 2. A critical component is any component of a life

systems which, (a) are intended for surgical implant support device or system whose failure to perform can

into the body, or (b) support or sustain life, and whose be reasonably expected to cause the failure of the life

failure to perform, when properly used in accordance support device or system, or to affect its safety or

with instructions for use provided in the labeling, can effectiveness.

be reasonably expected to result in a significant injury

to the user.

National Semiconductor National Semiconductor National Semiconductor National Semiconductor

Corporation Europe Hong Kong Ltd. Japan Ltd.

1111 West Bardin Road Fax: (

49) 0-180-530 85 86 13th Floor, Straight Block, Tel: 81-043-299-2309

Arlington, TX 76017 Email: cnjwge

tevm2.nsc.com Ocean Centre, 5 Canton Rd. Fax: 81-043-299-2408

Tel: 1(800) 272-9959 Deutsch Tel: (

49) 0-180-530 85 85 Tsimshatsui, Kowloon

Fax: 1(800) 737-7018 English Tel: (

49) 0-180-532 78 32 Hong Kong

Fran3ais Tel: (

49) 0-180-532 93 58 Tel: (852) 2737-1600

Italiano Tel: (

49) 0-180-534 16 80 Fax: (852) 2736-9960

National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications.