LM101A-N, LM201A-N, LM301A-N
www.ti.com
SNOSBS0D SEPTEMBER 1999REVISED MARCH 2013
LM101A/LM201A/LM301A Operational Amplifiers
Check for Samples: LM101A-N,LM201A-N,LM301A-N
1FEATURES DESCRIPTION
The LM101A series are general purpose operational
Improved Specifications include: amplifiers which feature improved performance over
Offset Voltage 3 mV Maximum Over industry standards like the LM709. Advanced
Temperature (LM101A/LM201A) processing techniques make possible an order of
Input Current 100 nA Maximum Over magnitude reduction in input currents, and a redesign
of the biasing circuitry reduces the temperature drift
Temperature (LM101A/LM201A) of input current.
Offset Current 20 nA Maximum Over
Temperature (LM101A/LM201A) This amplifier offers many features which make its
application nearly foolproof: Overload protection on
Specified Drift Characteristics the input and output, no latch-up when the common
Offsets Specified Over Entire Common Mode mode range is exceeded, and freedom from
and Supply Voltage Ranges oscillations and compensation with a single 30 pF
Slew Rate of 10V/μs as a Summing Amplifier Capacitor. It has advantages over internally
compensated amplifiers in that the frequency
compensation can be tailored to the particular
application. For example, in low frequency circuits it
can be overcompensated for increased stability
margin or the compensation can be optimized to give
more than a factor of ten improvement in high
frequency performance for most applications.
In Addition, the device provides better accuracy and
lower noise in high impedance circuitry. The low input
currents also make it particularly well suited for long
interval integrators or timers, sample and hold circuits
and low frequency waveform generators. Further,
replacing circuits where matched transistor pairs
buffer the inputs of conventional IC op amps, It can
give lower offset voltage and a drift at a lower cost.
The LM101A is ensured over a temperature range of
55°C to +125°C, the LM201A from 25°C to +85°C,
and the LM301A from 0°C to +70°C.
Fast AC-DC Converter
Feedforward compensation can be used to make a fast full wave rectifier without a filter.
1Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
PRODUCTION DATA information is current as of publication date. Copyright © 1999–2013, Texas Instruments Incorporated
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
LM101A-N, LM201A-N, LM301A-N
SNOSBS0D SEPTEMBER 1999REVISED MARCH 2013
www.ti.com
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
Absolute Maximum Ratings(1)(2)
LM101A/LM201A LM301A
Supply Voltage ±22V ±18V
Differential Input Voltage ±30V ±30V
Input Voltage(3) ±15V ±15V
Output Short Circuit Duration(4) Continuous Continuous
Operating Ambient Temp. Range 55°C to +125°C (LM101A) 0°C to +70°C
25°C to +85°C (LM201A)
TJMax
LMC0008C Package 150°C 100°C
P0008E Package 150°C 100°C
NAB0008A, J0014A Package 150°C 100°C
Power Dissipation at TA= 25°C
LMC0008C-Package (Still Air) 500 mW 300 mW
(400 LF/Min Air Flow) 1200 mW 700 mW
P0008E Package 900 mW 500 mW
NAB0008A, J0014A Package 1000 mW 650 mW
Thermal Resistance (Typical) θjA
LMC0008C Package (Still Air) 165°C/W 165°C/W
(400 LF/Min Air Flow) 67°C/W 67°C/W
P0008E Package 135°C/W 135°C/W
NAB0008A, J0014A Package 110°C/W 110°CmW
(Typical) θjC
LMC0008C Package 25°C/W 25°C/W
Storage Temperature Range 65°C to +150°C 65°C to +150°C
Lead Temperature (Soldering, 10 sec.)
LMC0008C or NAB0008A, J0014A, NAD0010A 300°C 300°C
P0008E 260°C 260°C
ESD Tolerance(5) 2000V 2000V
(1) Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating ratings indicate for which the
device is functional, but do no ensure specific performance limits. Electrical Characteristics state DC and AC electrical specifications
under particular test conditions which ensure specific limits. This assumes that the device is within the Operating Ratings. Specifications
are not ensured for parameters where no limit is given, however, the typical value is a good indication of device performance.
(2) If Military/Aerospace specified devices are required, please contact the Texas Instruments Sales Office/Distributors for availability and
specifications.
(3) For supply voltages less than ±15V, the absolute maximum input voltage is equal to the supply voltage.
(4) Continuous short circuit is allowed for case temperatures to 125°C and ambient temperatures to 75°C for LM101A/LM201A, and 70°C
and 55°C respectively for LM301A.
(5) Human body model, 100 pF discharged through 1.5 kΩ.
2Submit Documentation Feedback Copyright © 1999–2013, Texas Instruments Incorporated
Product Folder Links: LM101A-N LM201A-N LM301A-N
LM101A-N, LM201A-N, LM301A-N
www.ti.com
SNOSBS0D SEPTEMBER 1999REVISED MARCH 2013
Electrical Characteristics(1)
TA= TJLM101A/LM201A LM301A
Parameter Test Conditions Units
Min Typ Max Min Typ Max
Input Offset Voltage TA= 25°C, RS50 kΩ0.7 2.0 2.0 7.5 mV
Input Offset Current TA= 25°C 1.5 10 3.0 50 nA
Input Bias Current TA= 25°C 30 75 70 250 nA
Input Resistance TA= 25°C 1.5 4.0 0.5 2.0 MΩ
Supply Current TA= 25°C VS= ±20V 1.8 3.0 mA
VS= ±15V 1.8 3.0 mA
Large Signal Voltage Gain TA= 25°C, VS= ±15V 50 160 25 160 V/mV
VOUT = ±10V, RL2 kΩ
Input Offset Voltage RS50 kΩ3.0 10 mV
Average Temperature Coefficient of RS50 kΩ3.0 15 6.0 30 μV/°C
Input Offset Voltage
Input Offset Current 20 70 nA
Average Temperature Coefficient of 25°C TATMAX 0.01 0.1 0.01 0.3 nA/°C
Input Offset Current TMIN TA25°C 0.02 0.2 0.02 0.6 nA/°C
Input Bias Current 0.1 0.3 μA
Supply Current TA= TMAX, VS= ±20V 1.2 2.5 mA
Large Signal Voltage Gain VS= ±15V, VOUT = ±10V 25 15 V/mV
RL2k
Output Voltage Swing VS= ±15V RL= 10 kΩ±12 ±14 ±12 ±14 V
RL= 2 kΩ±10 ±13 ±10 ±13 V
Input Voltage Range VS= ±20V ±15 V
VS= ±15V +15, 13 ±12 +15, 13 V
Common-Mode Rejection Ratio RS50 kΩ80 96 70 90 dB
Supply Voltage Rejection Ratio RS50 kΩ80 96 70 96 dB
(1) Unless otherwise specified, these specifications apply for C1 = 30 pF, ±5V VS±20V and 55°C TA+125°C (LM101A), ±5V VS
±20V and 25°C TA+85°C (LM201A), ±5V VS±15V and 0°C TA+70°C (LM301A).
Copyright © 1999–2013, Texas Instruments Incorporated Submit Documentation Feedback 3
Product Folder Links: LM101A-N LM201A-N LM301A-N
LM101A-N, LM201A-N, LM301A-N
SNOSBS0D SEPTEMBER 1999REVISED MARCH 2013
www.ti.com
Typical Performance Characteristics
LM101A/LM201A
Input Voltage Range Output Swing
Figure 1. Figure 2.
Voltage Gain
Figure 3.
Performance Characteristics
LM301A
Input Voltage Range Output Swing
Figure 4. Figure 5.
4Submit Documentation Feedback Copyright © 1999–2013, Texas Instruments Incorporated
Product Folder Links: LM101A-N LM201A-N LM301A-N
LM101A-N, LM201A-N, LM301A-N
www.ti.com
SNOSBS0D SEPTEMBER 1999REVISED MARCH 2013
Performance Characteristics (continued)
LM301A Voltage Gain
Figure 6.
Copyright © 1999–2013, Texas Instruments Incorporated Submit Documentation Feedback 5
Product Folder Links: LM101A-N LM201A-N LM301A-N
LM101A-N, LM201A-N, LM301A-N
SNOSBS0D SEPTEMBER 1999REVISED MARCH 2013
www.ti.com
Typical Performance Characteristics
Supply Current Voltage Gain
Figure 7. Figure 8.
Input Current,
Maximum Power Dissipation LM101A/LM201A/LM301A
Figure 9. Figure 10.
Current Limiting Input Noise Voltage
Figure 11. Figure 12.
6Submit Documentation Feedback Copyright © 1999–2013, Texas Instruments Incorporated
Product Folder Links: LM101A-N LM201A-N LM301A-N
LM101A-N, LM201A-N, LM301A-N
www.ti.com
SNOSBS0D SEPTEMBER 1999REVISED MARCH 2013
Typical Performance Characteristics (continued)
Input Noise Current Common Mode Rejection
Figure 13. Figure 14.
Closed Loop Output
Power Supply Rejection Impedance
Figure 15. Figure 16.
Copyright © 1999–2013, Texas Instruments Incorporated Submit Documentation Feedback 7
Product Folder Links: LM101A-N LM201A-N LM301A-N
LM101A-N, LM201A-N, LM301A-N
SNOSBS0D SEPTEMBER 1999REVISED MARCH 2013
www.ti.com
Typical Performance Characteristics for Various Compensation Circuits
Pin connections shown are for 8-pin packages.
CS= 30 pF
CS= 30 pF
C2 = 10 C1
Figure 17. Single Pole Compensation Figure 18. Two Pole Compensation
Open Loop Frequency Response
fo= 3 MHz Figure 19. Feedforward Compensation Figure 20.
Open Loop Frequency Response Open Loop Frequency Response
Figure 21. Figure 22.
8Submit Documentation Feedback Copyright © 1999–2013, Texas Instruments Incorporated
Product Folder Links: LM101A-N LM201A-N LM301A-N
LM101A-N, LM201A-N, LM301A-N
www.ti.com
SNOSBS0D SEPTEMBER 1999REVISED MARCH 2013
Typical Performance Characteristics for Various Compensation Circuits (continued)
Large Signal Frequency Response Large Signal Frequency Response
Figure 23. Figure 24.
Large Signal Frequency Response Voltage Follower Pulse Response
Figure 25. Figure 26.
Voltage Follower Pulse Response Inverter Pulse Response
Figure 27. Figure 28.
Copyright © 1999–2013, Texas Instruments Incorporated Submit Documentation Feedback 9
Product Folder Links: LM101A-N LM201A-N LM301A-N
LM101A-N, LM201A-N, LM301A-N
SNOSBS0D SEPTEMBER 1999REVISED MARCH 2013
www.ti.com
TYPICAL APPLICATIONS
Pin connections shown are for 8-pin packages
LR1 R2 C1
RS= R2
RP= R1
Figure 29. Variable Capacitance Multiplier Figure 30. Simulated Inductor
Figure 31. Fast Inverting Amplifier with High
Input Impedance
fo= 10 kHz
Figure 33. Sine Wave Oscillator
†May be zero or equal to parallel
combination of R1 and R2 for minimum
offset.
*Adjust for zero integrator drift. Current drift
Figure 32. Inverting Amplifier with Balancing typically 0.1 nA/°C over 55°C to +125°C
Circuit temperature range.
Figure 34. Integrator with Bias Current
Compensation
10 Submit Documentation Feedback Copyright © 1999–2013, Texas Instruments Incorporated
Product Folder Links: LM101A-N LM201A-N LM301A-N
LM101A-N, LM201A-N, LM301A-N
www.ti.com
SNOSBS0D SEPTEMBER 1999REVISED MARCH 2013
Application Hints
Pin connections shown are for 8-pin packages.
*Protects input
†Protects output
‡Protects output—not needed when R4 is used.
Figure 35. Protecting Against Gross Fault Conditions
Figure 36. Compensating for Stray Input Capacitances or Large Feedback Resistor
Figure 37. Isolating Large Capacitive Loads
Copyright © 1999–2013, Texas Instruments Incorporated Submit Documentation Feedback 11
Product Folder Links: LM101A-N LM201A-N LM301A-N
LM101A-N, LM201A-N, LM301A-N
SNOSBS0D SEPTEMBER 1999REVISED MARCH 2013
www.ti.com
Although the LM101A is designed for trouble free operation, experience has indicated that it is wise to observe
certain precautions given below to protect the devices from abnormal operating conditions. It might be pointed
out that the advice given here is applicable to practically any IC op amp, although the exact reason why may
differ with different devices.
When driving either input from a low-impedance source, a limiting resistor should be placed in series with the
input lead to limit the peak instantaneous output current of the source to something less than 100 mA. This is
especially important when the inputs go outside a piece of equipment where they could accidentally be
connected to high voltage sources. Large capacitors on the input (greater than 0.1 μF) should be treated as a
low source impedance and isolated with a resistor. Low impedance sources do not cause a problem unless their
output voltage exceeds the supply voltage. However, the supplies go to zero when they are turned off, so the
isolation is usually needed.
The output circuitry is protected against damage from shorts to ground. However, when the amplifier output is
connected to a test point, it should be isolated by a limiting resistor, as test points frequently get shorted to bad
places. Further, when the amplifer drives a load external to the equipment, it is also advisable to use some sort
of limiting resistance to preclude mishaps.
Precautions should be taken to insure that the power supplies for the integrated circuit never become
reversed—even under transient conditions. With reverse voltages greater than 1V, the IC will conduct excessive
current, fusing internal aluminum interconnects. If there is a possibility of this happening, clamp diodes with a
high peak current rating should be installed on the supply lines. Reversal of the voltage between V+and Vwill
always cause a problem, although reversals with respect to ground may also give difficulties in many circuits.
The minimum values given for the frequency compensation capacitor are stable only for source resistances less
than 10 kΩ, stray capacitances on the summing junction less than 5 pF and capacitive loads smaller than 100
pF. If any of these conditions are not met, it becomes necessary to overcompensate the amplifier with a larger
compensation capacitor. Alternately, lead capacitors can be used in the feedback network to negate the effect of
stray capacitance and large feedback resistors or an RC network can be added to isolate capacitive loads.
Although the LM101A is relatively unaffected by supply bypassing, this cannot be ignored altogether. Generally it
is necessary to bypass the supplies to ground at least once on every circuit card, and more bypass points may
be required if more than five amplifiers are used. When feed-forward compensation is employed, however, it is
advisable to bypass the supply leads of each amplifier with low inductance capacitors because of the higher
frequencies involved.
12 Submit Documentation Feedback Copyright © 1999–2013, Texas Instruments Incorporated
Product Folder Links: LM101A-N LM201A-N LM301A-N
LM101A-N, LM201A-N, LM301A-N
www.ti.com
SNOSBS0D SEPTEMBER 1999REVISED MARCH 2013
Typical Applications
Pin connections shown are for 8-pin packages.
Figure 38. Standard Compensation and Offset Balancing Circuit
Power Bandwidth: 15 kHz
Slew Rate: 1V/μs
Figure 39. Fast Voltage Follower
Power Bandwidth: 250 kHz
Small Signal Bandwiidth: 3.5 MHz
Slew Rate: 10V/μs
Figure 40. Fast Summing Amplifier
Copyright © 1999–2013, Texas Instruments Incorporated Submit Documentation Feedback 13
Product Folder Links: LM101A-N LM201A-N LM301A-N
LM101A-N, LM201A-N, LM301A-N
SNOSBS0D SEPTEMBER 1999REVISED MARCH 2013
www.ti.com
R3 = R4 + R5
R1 = R2
Figure 41. Bilateral Current Source
Figure 42. Fast AC/DC Converter(1)
R1 = R4; R2 = R3
*,† Matching determines CMRR.
Figure 43. Instrumentation Amplifier
(1) Feedforward compensation can be used to make a fast full wave rectifier without a filter
14 Submit Documentation Feedback Copyright © 1999–2013, Texas Instruments Incorporated
Product Folder Links: LM101A-N LM201A-N LM301A-N
LM101A-N, LM201A-N, LM301A-N
www.ti.com
SNOSBS0D SEPTEMBER 1999REVISED MARCH 2013
*Adjust for zero integrator drift. Current drift typically 0.1 nA/°C over 0°C to +70°C temperature range.
Figure 44. Integrator with Bias Current Compensation
Figure 45. Voltage Comparator for Driving RTL Logic or High Current Driver
Figure 46. Low Frequency Square Wave Generator
*Polycarbonate-dielectric capacitor
Figure 47. Low Drift Sample and Hold
Copyright © 1999–2013, Texas Instruments Incorporated Submit Documentation Feedback 15
Product Folder Links: LM101A-N LM201A-N LM301A-N
LM101A-N, LM201A-N, LM301A-N
SNOSBS0D SEPTEMBER 1999REVISED MARCH 2013
www.ti.com
Figure 48. Voltage Comparator for Driving DTL or TTL Integrated Circuits
Schematic
Pin connections shown are for 8-pin packages.
16 Submit Documentation Feedback Copyright © 1999–2013, Texas Instruments Incorporated
Product Folder Links: LM101A-N LM201A-N LM301A-N
LM101A-N, LM201A-N, LM301A-N
www.ti.com
SNOSBS0D SEPTEMBER 1999REVISED MARCH 2013
Connection Diagrams
Top View Top View
Figure 49. CDIP and PDIP Packages
Package Number NAB0008A or P0008E
Top View Figure 51. TO-99 Package
See Package Number LMC0008C
Top View
Figure 50. CLGA Package
Package Number NAD0010A
Figure 52. CDIP Package
See Package Number J0014A,
Copyright © 1999–2013, Texas Instruments Incorporated Submit Documentation Feedback 17
Product Folder Links: LM101A-N LM201A-N LM301A-N
LM101A-N, LM201A-N, LM301A-N
SNOSBS0D SEPTEMBER 1999REVISED MARCH 2013
www.ti.com
REVISION HISTORY
Changes from Revision C (March 2013) to Revision D Page
Changed layout of National Data Sheet to TI format .......................................................................................................... 17
18 Submit Documentation Feedback Copyright © 1999–2013, Texas Instruments Incorporated
Product Folder Links: LM101A-N LM201A-N LM301A-N
PACKAGE OPTION ADDENDUM
www.ti.com 4-Feb-2021
Addendum-Page 1
PACKAGING INFORMATION
Orderable Device Status
(1)
Package Type Package
Drawing Pins Package
Qty Eco Plan
(2)
Lead finish/
Ball material
(6)
MSL Peak Temp
(3)
Op Temp (°C) Device Marking
(4/5)
Samples
LM101AH ACTIVE TO-99 LMC 8 500 Non-RoHS &
Non-Green Call TI Call TI -55 to 125 ( LM101AH, LM101AH
)
LM101AH/NOPB ACTIVE TO-99 LMC 8 500 RoHS & Green Call TI Level-1-NA-UNLIM -55 to 125 ( LM101AH, LM101AH
)
LM101AJ ACTIVE CDIP NAB 8 40 Non-RoHS
& Green Call TI Call TI -55 to 125 LM101AJ
LM201AH ACTIVE TO-99 LMC 8 500 Non-RoHS &
Non-Green Call TI Call TI -40 to 85 ( LM201AH, LM201AH
)
LM201AH/NOPB ACTIVE TO-99 LMC 8 500 RoHS & Green Call TI Level-1-NA-UNLIM -40 to 85 ( LM201AH, LM201AH
)
LM301AH ACTIVE TO-99 LMC 8 500 Non-RoHS &
Non-Green Call TI Call TI 0 to 70 ( LM301AH, LM301AH
)
LM301AH/NOPB ACTIVE TO-99 LMC 8 500 RoHS & Green Call TI Level-1-NA-UNLIM 0 to 70 ( LM301AH, LM301AH
)
(1) The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2) RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance
do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may
reference these types of products as "Pb-Free".
RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption.
Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of <=1000ppm threshold. Antimony trioxide based
flame retardants must also meet the <=1000ppm threshold requirement.
(3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
PACKAGE OPTION ADDENDUM
www.ti.com 4-Feb-2021
Addendum-Page 2
(6) Lead finish/Ball material - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead finish/Ball material values may wrap to two
lines if the finish value exceeds the maximum column width.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
MECHANICAL DATA
NAB0008A
www.ti.com
J08A (Rev M)
IMPORTANT NOTICE AND DISCLAIMER
TI PROVIDES TECHNICAL AND RELIABILITY DATA (INCLUDING DATASHEETS), DESIGN RESOURCES (INCLUDING REFERENCE
DESIGNS), APPLICATION OR OTHER DESIGN ADVICE, WEB TOOLS, SAFETY INFORMATION, AND OTHER RESOURCES “AS IS”
AND WITH ALL FAULTS, AND DISCLAIMS ALL WARRANTIES, EXPRESS AND IMPLIED, INCLUDING WITHOUT LIMITATION ANY
IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR NON-INFRINGEMENT OF THIRD
PARTY INTELLECTUAL PROPERTY RIGHTS.
These resources are intended for skilled developers designing with TI products. You are solely responsible for (1) selecting the appropriate
TI products for your application, (2) designing, validating and testing your application, and (3) ensuring your application meets applicable
standards, and any other safety, security, or other requirements. These resources are subject to change without notice. TI grants you
permission to use these resources only for development of an application that uses the TI products described in the resource. Other
reproduction and display of these resources is prohibited. No license is granted to any other TI intellectual property right or to any third party
intellectual property right. TI disclaims responsibility for, and you will fully indemnify TI and its representatives against, any claims, damages,
costs, losses, and liabilities arising out of your use of these resources.
TI’s products are provided subject to TI’s Terms of Sale (https:www.ti.com/legal/termsofsale.html) or other applicable terms available either
on ti.com or provided in conjunction with such TI products. TI’s provision of these resources does not expand or otherwise alter TI’s
applicable warranties or warranty disclaimers for TI products.IMPORTANT NOTICE
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2021, Texas Instruments Incorporated