INDUCTORS
MLG0603P 0603 [0201 inch]*
* Dimensions Code JIS[EIA]
October 2013
Inductors for High Frequency Circuits
Multilayer Ceramic
MLG-Pseries (For automobiles)
(2/12)
INDUCTORS
001-01 / 20131001 / inductor_automotive_high-frequency_mlg-qp_en.fm
REMINDERS FOR USING THESE PRODUCTS
Before using these products, be sure to request the delivery specifications.
SAFETY REMINDERS
Please pay sufficient attention to the warnings for safe designing when using these products.
The storage period is less than 12 months. Be sure to follow the storage conditions (Temperature: 5 to 40°C, Humidity: 10 to 75% RH
or less).
If the storage period elapses, the soldering of the terminal electrodes may deteriorate.
Do not use or store in locations where there are conditions such as gas corrosion (salt, acid, alkali, etc.).
Before soldering, be sure to preheat components.
The preheating temperature should be set so that the temperature difference between the solder temperature and chip temperature
does not exceed 150°C.
Soldering corrections after mounting should be within the range of the conditions determined in the specifications.
If overheated, a short circuit, performance deterioration, or lifespan shortening may occur.
When embedding a printed circuit board where a chip is mounted to a set, be sure that residual stress is not given to the chip due to
the overall distortion of the printed circuit board and partial distortion such as at screw tightening portions.
Self heating (temperature increase) occurs when the power is turned ON, so the tolerance should be sufficient for the set thermal
design.
Carefully lay out the coil for the circuit board design of the non-magnetic shield type.
A malfunction may occur due to magnetic interference.
Use a wrist band to discharge static electricity in your body through the grounding wire.
Do not expose the products to magnets or magnetic fields.
Do not use for a purpose outside of the contents regulated in the delivery specifications.
The products listed on this catalog are intended for use in general electronic equipment (AV equipment, telecommunications
equipment, home appliances, amusement equipment, computer equipment, personal equipment, office equipment, measurement
equipment, industrial robots) under a normal operation and use condition.
The products are not designed or warranted to meet the requirements of the applications listed below, whose performance and/or
quality require a more stringent level of safety or reliability, or whose failure, malfunction or trouble could cause serious damage to
society, person or property.
If you intend to use the products in the applications listed below or if you have special requirements exceeding the range or conditions
set forth in the each catalog, please contact us.
(1) Aerospace/Aviation equipment
(2) Transportation equipment (cars, electric trains, ships, etc.)
(3) Medical equipment
(4) Power-generation control equipment
(5) Atomic energy-related equipment
(6) Seabed equipment
(7) Transportation control equipment
(8) Public information-processing equipment
(9) Military equipment
(10) Electric heating apparatus, burning equipment
(11) Disaster prevention/crime prevention equipment
(12) Safety equipment
(13) Other applications that are not considered general-purpose
applications
When designing your equipment even for general-purpose applications, you are kindly requested to take into consideration securing
protection circuit/device or providing backup circuits in your equipment.
REMINDERS
(3/12)
INDUCTORS
001-01 / 20131001 / inductor_automotive_high-frequency_mlg-qp_en.fm
• All specifications are subject to change without notice.
Inductors for High Frequency Circuits
Multilayer Ceramic
FEATURES
High Q type inductor for high-frequency circuits.
The 0402 Series has0.2 to 33nH, and the 0603 Series has 0.6 to 120nH.
0.1n step inductance lineup.
Compared with existing products, the size was greatly reduced, making it optimal for fine-pitch circuits.
Optimal configuration that greatly improves the Q to 800MHz or higher.
Advanced monolithic structure is formed using a multilayering and sintering process with ceramic and conductive materials for High-
frequency.
APPLICATION
Automotive equipment, smart phones, tablet terminals, high frequency modules (PAs, VCOs, FEMs , etc.), Bluetooth, W-LAN, UWB, tuners
and other high frequency circuits for the mobile communication industry
PART NUMBER CONSTRUCTION
OPERATING TEMPERATURE RANGE, PACKAGE QUANTITY, PRODUCT WEIGHT
The Storage temperature range is for after the circuit board is mounted.
Product compatible with RoHS directive
Halogen-free
Compatible with lead-free solders
AEC-Q200
Overview of the MLG-P Series
MLG 0603 P 1N1 B T □□□
Series name L×W×H Dimensions Characteristics Inductance Inductance
tolerance Packaging style Internal code
(mm) (μH)
0603 0.6×0.3×0.3 P 1N1 1.1 B ±0.1nH T Taping
11N 11 C ±0.2nH
S ±0.3nH
3%
5%
Type
Temperature range
Package quantity Individual weight
Operating
temperature
Storage
temperature
°C °C(pieces/reel) mg
MLG0603P –55 to +125 –55 to +125 15000 0.2
RoHS Directive Compliant Product: See the following for more details related to RoHS Directive compliant products. http://www.tdk.co.jp/rohs/
Halogen-free: Indicates that Cl content is less than 900ppm, Br content is less than 900ppm, and that the total Cl and Br content is less than 1500ppm.
(4/12)
INDUCTORS
001-01 / 20131001 / inductor_automotive_high-frequency_mlg-qp_en.fm
• All specifications are subject to change without notice.
Overview of the MLG-P Series
RECOMMENDED REFLOW PROFILE
Preheating Soldering Peak
Temp. Time Temp. Time Temp. Time
T1 T2 t1 T3 t2 T4 t3
150°C 180°C 60 to 120s 230°C 30 to 60s 250 to 260°C 10s max.
Natural
cooling
t3
t1
Preheating
t2
Soldering
T3 T3
T4
T2
T1
t: Time
Peak
T: Temperature
(5/12)
INDUCTORS
001-01 / 20131001 / inductor_automotive_high-frequency_mlg-qp_en.fm
• All specifications are subject to change without notice.
MLG-Pseries
MLG0603P Type
SHAPE & DIMENSIONS
RECOMMENDED LAND PATTERN
Dimensions in mm
0.15±0.050.15±0.05
0.60±0.03
0.09±0.04 0.09±0.04
0.30±0.030.30±0.03
Dimensions in mm
0.3
0.3 0.250.25
(6/12)
INDUCTORS
001-01 / 20131001 / inductor_automotive_high-frequency_mlg-qp_en.fm
• All specifications are subject to change without notice.
MLG-PseriesMLG0603P Type
ELECTRICAL CHARACTERISTICS
CHARACTERISTICS SPECIFICATION TABLE
 The " " of the Part Number contains the inductance tolerance code, B(±0.1nH), C(±0.2nH), S(±0.3nH), H(±3%) or J(±5%).
Please contact us for information on inductance tolerance, G (±2%).
* The " □□□ " of the Part Number contains the internal code.
Short bar residual inductance =0.43nH
Measurement equipment
Equivalent measurement equipment may be used.
LQ
min.
L, Q measuring
frequency
(MHz)
Self-resonant
frequency
(GHz)
DC resistance
(:)
Rated current
(mA)
max.
Part No.
(nH) Tolerance min. typ. max. typ.
0.6 ±0.1, ±0.2nH 500 10.0 20.0 0.06 0.01 1000 MLG0603P0N6T□□□
0.7 ±0.1, ±0.2nH 500 10.0 20.0 0.06 0.01 1000 MLG0603P0N7T□□□
0.8 ±0.1, ±0.2nH 500 10.0 20.0 0.06 0.02 1000 MLG0603P0N8T□□□
0.9 ±0.1, ±0.2nH 500 10.0 20.0 0.06 0.02 1000 MLG0603P0N9T□□□
1.0 ±0.1, ±0.2, 0.3nH 14 500 10.0 20.0 0.07 0.02 1000 MLG0603P1N0T□□□
1.1 ±0.1, ±0.2, 0.3nH 14 500 10.0 19.9 0.07 0.03 1000 MLG0603P1N1T□□□
1.2 ±0.1, ±0.2, 0.3nH 14 500 10.0 16.0 0.08 0.04 800 MLG0603P1N2T□□□
1.3 ±0.1, ±0.2, 0.3nH 14 500 10.0 13.9 0.08 0.03 800 MLG0603P1N3T□□□
1.4 ±0.1, ±0.2, 0.3nH 14 500 10.0 11.7 0.09 0.04 800 MLG0603P1N4T□□□
1.5 ±0.1, ±0.2, 0.3nH 14 500 10.0 14.9 0.10 0.03 800 MLG0603P1N5T□□□
1.6 ±0.1, ±0.2, 0.3nH 14 500 10.0 13.4 0.10 0.03 700 MLG0603P1N6T□□□
1.7 ±0.1, ±0.2, 0.3nH 14 500 10.0 12.8 0.10 0.02 700 MLG0603P1N7T□□□
1.8 ±0.1, ±0.2, 0.3nH 14 500 9.0 10.7 0.10 0.03 700 MLG0603P1N8T□□□
1.9 ±0.1, ±0.2, 0.3nH 14 500 9.0 10.9 0.10 0.04 600 MLG0603P1N9T□□□
2.0 ±0.1, ±0.2, 0.3nH 14 500 8.5 10.1 0.10 0.03 600 MLG0603P2N0T□□□
2.1 ±0.1, ±0.2, 0.3nH 14 500 8.0 9.8 0.10 0.05 600 MLG0603P2N1T□□□
2.2 ±0.1, ±0.2, 0.3nH 14 500 7.5 9.0 0.10 0.07 600 MLG0603P2N2T□□□
2.3 ±0.1, ±0.2, 0.3nH 14 500 7.5 8.4 0.20 0.07 600 MLG0603P2N3T□□□
2.4 ±0.1, ±0.2, 0.3nH 14 500 7.5 10.9 0.20 0.12 500 MLG0603P2N4T□□□
2.5 ±0.1, ±0.2, 0.3nH 14 500 7.5 9.9 0.20 0.09 500 MLG0603P2N5T□□□
2.6 ±0.1, ±0.2, 0.3nH 14 500 7.5 10.1 0.20 0.14 500 MLG0603P2N6T□□□
2.7 ±0.1, ±0.2, 0.3nH 14 500 7.5 10.0 0.20 0.14 500 MLG0603P2N7T□□□
2.8 ±0.1, ±0.2, 0.3nH 14 500 7.5 9.9 0.20 0.10 500 MLG0603P2N8T□□□
2.9 ±0.1, ±0.2, 0.3nH 14 500 7.5 9.2 0.20 0.10 500 MLG0603P2N9T□□□
3.0 ±0.1, ±0.2, 0.3nH 14 500 7.5 9.1 0.20 0.14 450 MLG0603P3N0T□□□
3.1 ±0.1, ±0.2, 0.3nH 14 500 7.5 8.8 0.20 0.10 450 MLG0603P3N1T□□□
3.2 ±0.1, ±0.2, 0.3nH 14 500 7.5 8.4 0.20 0.14 450 MLG0603P3N2T□□□
3.3 ±0.1, ±0.2, 0.3nH 14 500 7.5 8.4 0.20 0.13 450 MLG0603P3N3T□□□
3.4 ±0.1, ±0.2, 0.3nH 14 500 7.0 8.1 0.20 0.13 450 MLG0603P3N4T□□□
3.5 ±0.1, ±0.2, 0.3nH 14 500 6.5 8.0 0.20 0.12 450 MLG0603P3N5T□□□
3.6 ±0.1, ±0.2, 0.3nH 14 500 6.5 7.7 0.20 0.10 400 MLG0603P3N6T□□□
3.7 ±0.1, ±0.2, 0.3nH 14 500 6.5 7.4 0.20 0.14 400 MLG0603P3N7T□□□
3.8 ±0.1, ±0.2, 0.3nH 14 500 5.8 7.0 0.30 0.24 400 MLG0603P3N8T□□□
3.9 ±0.1, ±0.2, 0.3nH 14 500 5.8 7.1 0.30 0.22 400 MLG0603P3N9T□□□
4.0 ±0.1, ±0.2, 0.3nH 14 500 5.8 6.7 0.40 0.21 350 MLG0603P4N0T□□□
4.1 ±0.1, ±0.2, 0.3nH 14 500 5.8 6.7 0.40 0.29 350 MLG0603P4N1T□□□
4.2 ±0.1, ±0.2, 0.3nH 14 500 5.8 6.6 0.40 0.24 350 MLG0603P4N2T□□□
4.3 ±3%, ±5%, ±0.3nH 14 500 5.8 6.7 0.40 0.24 350 MLG0603P4N3T□□□
4.7 ±3%, ±5%, ±0.3nH 14 500 5.5 6.9 0.40 0.16 350 MLG0603P4N7T□□□
5.1 ±3%, ±5%, ±0.3nH 14 500 5.5 6.6 0.40 0.30 350 MLG0603P5N1T□□□
5.6 ±3%, ±5%, ±0.3nH 14 500 4.0 5.3 0.40 0.32 350 MLG0603P5N6T□□□
6.2 ±3%, ±5%, ±0.3nH 14 500 4.0 6.3 0.70 0.59 300 MLG0603P6N2T□□□
6.8 ±3%, ±5% 14 500 4.0 6.1 0.75 0.62 300 MLG0603P6N8T□□□
7.5 ±3%, ±5% 14 500 4.0 5.4 0.80 0.70 300 MLG0603P7N5T□□□
8.2 ±3%, ±5% 14 500 4.0 5.2 0.85 0.71 250 MLG0603P8N2T□□□
9.1 ±3%, ±5% 14 500 4.0 5.0 0.90 0.76 250 MLG0603P9N1T□□□
Measurement item Product No. Manufacturer
L, Q 4291B+16197A Agilent Technologies
Self-resonant frequency 8720C Agilent Technologies
DC resistance Type-7561 Yokogawa
(7/12)
INDUCTORS
001-01 / 20131001 / inductor_automotive_high-frequency_mlg-qp_en.fm
• All specifications are subject to change without notice.
MLG-PseriesMLG0603P Type
ELECTRICAL CHARACTERISTICS
CHARACTERISTICS SPECIFICATION TABLE
 The " " of the Part Number contains the inductance tolerance code, B(±0.1nH), C(±0.2nH), S(±0.3nH), H(±3%) or J(±5%).
Please contact us for information on inductance tolerance, G (±2%).
* The " □□□ " of the Part Number contains the internal code.
Short bar residual inductance =0.43nH
Measurement equipment
Equivalent measurement equipment may be used.
LQ
min.
L, Q measuring
frequency
(MHz)
Self-resonant
frequency
(GHz)
DC resistance
(:)
Rated current
(mA)
max.
Part No.
(nH) tolerance min. typ. max. typ.
10 ±3%, ±5% 14 500 4.0 4.7 0.95 0.85 250 MLG0603P10NT□□□
11 ±3%, ±5% 14 500 3.5 4.5 1.00 0.64 250 MLG0603P11NT□□□
12 ±3%, ±5% 14 500 3.5 4.3 1.10 0.82 250 MLG0603P12NT□□□
13 ±3%, ±5% 14 500 3.2 4.2 1.10 0.87 250 MLG0603P13NT□□□
15 ±3%, ±5% 14 500 3.2 3.7 1.20 0.94 250 MLG0603P15NT□□□
16 ±3%, ±5% 14 500 3.0 3.6 1.20 1.00 200 MLG0603P16NT□□□
18 ±3%, ±5% 14 500 3.0 3.5 1.40 1.04 200 MLG0603P18NT□□□
20 ±3%, ±5% 14 500 2.2 3.3 1.90 1.33 150 MLG0603P20NT□□□
22 ±3%, ±5% 14 500 2.2 2.9 1.90 1.31 150 MLG0603P22NT□□□
24 ±3%, ±5% 14 500 2.2 2.9 2.10 1.17 140 MLG0603P24NT□□□
27 ±3%, ±5% 14 500 2.2 2.7 2.10 1.45 140 MLG0603P27NT□□□
30 ±3%, ±5% 10 300 1.8 2.3 2.20 1.37 130 MLG0603P30NT□□□
33 ±3%, ±5% 10 300 1.8 2.4 2.20 1.55 130 MLG0603P33NT□□□
36 ±3%, ±5% 10 300 1.8 2.2 2.40 1.49 120 MLG0603P36NT□□□
39 ±3%, ±5% 10 300 1.8 2.2 2.40 1.72 120 MLG0603P39NT□□□
43 ±3%, ±5% 10 300 1.6 2.0 2.90 1.61 110 MLG0603P43NT□□□
47 ±3%, ±5% 10 300 1.6 2.0 2.90 2.18 110 MLG0603P47NT□□□
51 ±3%, ±5% 10 300 1.4 1.9 3.50 1.87 100 MLG0603P51NT□□□
56 ±3%, ±5% 10 300 1.4 1.8 3.50 2.35 100 MLG0603P56NT□□□
62 ±3%, ±5% 10 300 1.2 1.6 3.50 2.12 100 MLG0603P62NT□□□
68 ±3%, ±5% 9 300 1.2 1.6 3.50 2.69 100 MLG0603P68NT□□□
75 ±3%, ±5% 9300 1.0 1.5 4.00 2.59 80 MLG0603P75NT□□□
82 ±3%, ±5% 9 300 1.0 1.5 4.00 2.71 80 MLG0603P82NT□□□
91 ±3%, ±5% 9300 0.9 1.3 4.50 2.92 80 MLG0603P91NT□□□
100 ±3%, ±5% 9 300 0.9 1.3 4.50 3.20 80 MLG0603PR10T□□□
110 ±3%, ±5% 9300 0.8 1.1 5.00 3.50 80 MLG0603PR11T□□□
120 ±3%, ±5% 9 300 0.8 1.0 5.00 3.79 80 MLG0603PR12T□□□
Measurement item Product No. Manufacturer
L, Q 4291B+16197A Agilent Technologies
Self-resonant frequency 8720C Agilent Technologies
DC resistance Type-7561 Yokogawa
(8/12)
INDUCTORS
001-01 / 20131001 / inductor_automotive_high-frequency_mlg-qp_en.fm
• All specifications are subject to change without notice.
MLG-PseriesMLG0603P Type
ELECTRICAL CHARACTERISTICS
L, Q FREQUENCY CHARACTERISTICS TABLE
The " " of the Part Number contains the inductance tolerance code, B(±0.1nH), C(±0.2nH), S(±0.3nH), H(±3%) or J(±5%).
Please contact us for information on inductance tolerance, G (±2%).
* The " □□□ " of the Part Number contains the internal code.
Measurement equipment
Equivalent measurement equipment may be used.
L(nH)typ. Q typ. Part No.
500MHz 800MHz 1.8GHz 2.0GHz 2.4GHz 500MHz 800MHz 1.8GHz 2.0GHz 2.4GHz
0.6 0.6 0.6 0.6 0.6 16min. 22min. 35min. 37min. 41min. MLG0603P0N6T□□□
0.7 0.7 0.7 0.7 0.7 16min. 22min. 35min. 37min. 41min. MLG0603P0N7T□□□
0.8 0.8 0.8 0.8 0.4 16 22 35 37 41 MLG0603P0N8T□□□
0.9 0.9 0.9 0.9 0.9 17 22 35 37 41 MLG0603P0N9T□□□
1.0 1.0 1.0 1.0 1.0 16 21 33 36 40 MLG0603P1N0T□□□
1.1 1.1 1.1 1.1 1.1 17 23 36 38 43 MLG0603P1N1T□□□
1.2 1.2 1.2 1.2 1.2 18 24 38 40 45 MLG0603P1N2T□□□
1.3 1.3 1.3 1.3 1.3 17 22 34 36 40 MLG0603P1N3T□□□
1.4 1.4 1.4 1.4 1.4 18 23 36 39 43 MLG0603P1N4T□□□
1.5 1.5 1.5 1.5 1.5 17 22 33 35 39 MLG0603P1N5T□□□
1.6 1.6 1.6 1.6 1.6 17 22 33 35 38 MLG0603P1N6T□□□
1.7 1.7 1.7 1.7 1.7 17 22 33 35 39 MLG0603P1N7T□□□
1.8 1.8 1.8 1.8 1.8 17 22 34 35 39 MLG0603P1N8T□□□
1.9 1.9 1.9 1.9 1.9 18 24 36 38 42 MLG0603P1N9T□□□
2.0 2.0 2.0 2.0 2.0 19 23 35 37 41 MLG0603P2N0T□□□
2.1 2.1 2.1 2.1 2.1 18 23 34 36 39 MLG0603P2N1T□□□
2.2 2.2 2.2 2.2 2.3 18 23 35 36 40 MLG0603P2N2T□□□
2.3 2.3 2.3 2.4 2.4 18 22 33 35 38 MLG0603P2N3T□□□
2.4 2.4 2.4 2.4 2.4 16 21 31 33 36 MLG0603P2N4T□□□
2.5 2.5 2.5 2.5 2.5 17 22 33 34 38 MLG0603P2N5T□□□
2.6 2.6 2.6 2.6 2.6 17 22 33 35 38 MLG0603P2N6T□□□
2.7 2.7 2.7 2.7 2.7 17 21 33 35 38 MLG0603P2N7T□□□
2.8 2.8 2.8 2.8 2.9 17 22 34 36 40 MLG0603P2N8T□□□
2.9 2.9 2.9 2.9 3.0 17 22 34 35 39 MLG0603P2N9T□□□
3.0 3.0 3.0 3.1 3.1 17 21 32 34 37 MLG0603P3N0T□□□
3.1 3.1 3.1 3.2 3.2 17 22 33 34 37 MLG0603P3N1T□□□
3.2 3.2 3.2 3.3 3.3 17 22 34 35 38 MLG0603P3N2T□□□
3.3 3.3 3.4 3.4 3.4 18 22 33 35 38 MLG0603P3N3T□□□
3.4 3.4 3.5 3.5 3.6 18 23 34 35 38 MLG0603P3N4T□□□
3.5 3.5 3.6 3.6 3.7 18 23 34 35 38 MLG0603P3N5T□□□
3.6 3.6 3.7 3.7 3.8 18 22 33 34 37 MLG0603P3N6T□□□
3.7 3.7 3.8 3.9 4.0 18 23 34 35 37 MLG0603P3N7T□□□
3.8 3.8 3.9 4.0 4.1 17 22 32 33 36 MLG0603P3N8T□□□
3.9 3.9 4.0 4.1 4.2 17 22 32 34 36 MLG0603P3N9T□□□
4.0 4.0 4.1 4.2 4.4
18 22 32 33 36 MLG0603P4N0T□□□
4.1 4.1 4.3 4.3 4.5
18 22 33 34 36 MLG0603P4N1T□□□
4.2 4.2 4.4 4.5 4.6
18 22 32 33 35 MLG0603P4N2T□□□
4.3 4.3 4.5 4.5 4.7 17 21 32 33 35 MLG0603P4N3T□□□
4.7 4.7 4.9 5.0 5.1 16 21 31 32 34 MLG0603P4N7T□□□
5.1 5.1 5.3 5.4 5.7 16 21 31 32 34 MLG0603P5N1T□□□
5.6 5.6 6.1 6.2 6.6 18 22 31 32 32 MLG0603P5N6T□□□
6.2 6.2 6.5 6.7 7.0 16 21 30 31 33 MLG0603P6N2T□□□
6.8 6.8 7.3 7.5 8.0 16 21 29 30 31 MLG0603P6N8T□□□
7.5 7.5 8.1 8.3 8.8 16 21 30 30 32 MLG0603P7N5T□□□
8.2 8.2 9.0 9.3 10.0 17 21 30 30 31 MLG0603P8N2T□□□
9.1 9.1 10.0 10.3 11.1 17 21 30 31 32 MLG0603P9N1T□□□
Product No. Manufacturer
4291B+16197A Agilent Technologies
(9/12)
INDUCTORS
001-01 / 20131001 / inductor_automotive_high-frequency_mlg-qp_en.fm
• All specifications are subject to change without notice.
MLG-PseriesMLG0603P Type
ELECTRICAL CHARACTERISTICS
L, Q FREQUENCY CHARACTERISTICS TABLE
The " " of the Part Number contains the inductance tolerance code, B(±0.1nH), C(±0.2nH), S(±0.3nH), H(±3%) or J(±5%).
Please contact us for information on inductance tolerance, G (±2%).
* The " □□□ " of the Part Number contains the internal code.
Measurement equipment
Equivalent measurement equipment may be used.
L(nH)typ. Q typ. Part No.
500MHz 800MHz 1.8GHz 2.0GHz 2.4GHz 500MHz 800MHz 1.8GHz 2.0GHz 2.4GHz
10 10 11 12 13 16 21 28 28 28 MLG0603P10NT□□□
11 11 13 13 15
18 23 30 30 30 MLG0603P11NT□□□
12 12 14 15 17 18 22 28 28 27 MLG0603P12NT□□□
13 13 15 16 19
18 22 28 28 26 MLG0603P13NT□□□
15 15 18 20 24 18 22 27 26 24 MLG0603P15NT□□□
16 16 20 22 27
18 22 26 25 22 MLG0603P16NT□□□
18 18 23 26 33 18 22 25 24 20 MLG0603P18NT□□□
20 21 27 31 42
18 22 23 22 17 MLG0603P20NT□□□
22 23 34 40 68 18 21 21 18 11 MLG0603P22NT□□□
24 25 36 43 72
19 22 21 18 11 MLG0603P24NT□□□
27 28 45 57 18 21 18 15 MLG0603P27NT□□□
30 32 59
18 21 15 MLG0603P30NT□□□
33 36 68 15 17 11 MLG0603P33NT□□□
37 39
16 17 MLG0603P36NT□□□
40 43 15 17 MLG0603P39NT□□□
44 48
15 16 MLG0603P43NT□□□
48 53 15 16 MLG0603P47NT□□□
53 59
15 16 MLG0603P51NT□□□
58 66 15 15 MLG0603P56NT□□□
65 76
15 15 MLG0603P62NT□□□
71 82 15 15 MLG0603P68NT□□□
79 97
14 13 MLG0603P75NT□□□
87 109 14 13 MLG0603P82NT□□□
99 132
13 12 MLG0603P91NT□□□
110 152 14 12 MLG0603PR10T□□□
126 211
13 9 MLG0603PR11T□□□
151 12 MLG0603PR12T□□□
Product No. Manufacturer
4291B+16197A Agilent Technologies
(10/12)
INDUCTORS
001-01 / 20131001 / inductor_automotive_high-frequency_mlg-qp_en.fm
• All specifications are subject to change without notice.
MLG-PseriesMLG0603P Type
ELECTRICAL CHARACTERISTICS
L FREQUENCY CHARACTERISTICS GRAPH (EXAMPLE)
Measurement equipment
Equivalent measurement equipment may be used.
10 100 1000 10000
0
1000
100
10
1
Frequency(MHz)
Inductance(nH)
R12
R10
82N 68N
56N
47N39N
33N 27N
22N
18N
15N
12N
10N
8N2
6N8
5N6
4N7
3N9
3N3
2N7
2N2
1N8
1N5
1N2
1N0
Product No. Manufacturer
E4991A+16197A Agilent Technologies
(11/12)
INDUCTORS
001-01 / 20131001 / inductor_automotive_high-frequency_mlg-qp_en.fm
• All specifications are subject to change without notice.
MLG-PseriesMLG0603P Type
ELECTRICAL CHARACTERISTICS
Q FREQUENCY CHARACTERISTICS GRAPH (EXAMPLE)
Measurement equipment
Equivalent measurement equipment may be used.
0
10
20
30
40
50
Q
10 100 1000 10000
Frequency(MHz)
R12 R10
27N
22N
18N
15N
12N
10N
8N2
6N8
5N6
4N7
3N9
3N3
2N7
1N8
1N2
1N0
39N
56N
47N
68N
82N
33N
1N5
2N2
Product No. Manufacturer
E4991A+16197A Agilent Technologies
(12/12)
INDUCTORS
001-01 / 20131001 / inductor_automotive_high-frequency_mlg-qp_en.fm
• All specifications are subject to change without notice.
MLG-Pseries
Packaging Style
REEL DIMENSIONS
TAPE DIMENSIONS
1.0
ø180±2.0
2.0±0.5
ø13±0.2
ø21±0.8
ø60min.
14.4max.
Dimensions in mm
8.4 +2.0
–0.0
8.0±0.3 3.5±0.05
1.75±0.1
4.0±0.1
1.5 +0.1
–0.0
Sprocket hole Cavity
A
KB
2.0±0.05 2.0±0.05
160min. Taping 200min.
300min.
Drawing direction
Typ e A B K
MLG0603P 0.68±0.05 0.38±0.05 0.5 max.