BATTERY-POWERED DIGITAL PRESSURE GAUGES
SenSym ICT
SDPGB Series
Battery-Powered
Digital Pressure
Gauges
APPLICATIONS
FEATURES
±0.25% Test Gauge
Accuracy
316 Stainless Steel
Sensor
Long Battery Life
Rugged Design
Process Control
Test and
Measurement
0-15 psig to 0-1000 psig,
and -30 in Hg to 100 psi
The SenSym ICT Digital Pressure Gauge Series
devices are designed for pressure applications that
involve measurement of any media compatible with
316 stainless steel. With its common 1/4" NPT
fitting, the device is designed for many applications
requiring precision, ruggedness and reliability
combined with a long battery life. The digital
readout provides real-time information at the push
of a button.
Designed for battery operation, this digital gauge
has an automatic shutoff feature allowing the user
to walk away after taking a reading. The SenSym
ICT Digital Pressure Gauge Series is designed for
long-term usage. Zero and Span calibration are
both possible, but only when the user has access to
a reliable pressure reference of known accuracy.
Contact your local SenSym ICT representative, the
factory, or go to SenSym ICT's web site at
www.sensym-ict.com for additional details.
BATTERY-POWERED DIGITAL PRESSURE GAUGES
SenSym ICT
SDPGB Series
SenSym ICT
Span Zero
Made in USA
PSIG
Tighten
at hex
fitting
only
1.65"
2.88"
.75"
1/4"NPT
3.38"
SenSym ICT maintains a constant effort to upgrade and improve its products,
therefore specifications are subject to change. © Copyright 09/01
1 408 954 6700
FAX: 408 954 9458
SenSym ICT
1804 McCarthy Boulevard
Milpitas, CA 95035
www.sensym-ict.com
GENERAL DISCLAIMER: Invensys Sensor Systems reserves the right to make changes to its
products and their specifications at any time, without prior notice to anyone. Invensys Sensor
Systems has made every effort to ensure accuracy of the information contained herein but can
assume no responsibility for inadvertent errors, omissions, or subsequent changes. Invensys Sensor
Systems does not assume any responsibility for the use of any circuit or other information described
within this document, and further, makes no representations of any kind that the circuit and
information described herein is free of infringement of any intellectual property right or any other
right of third parties. No express or implied licenses of any Invensys Sensor Systems intellectual
property right is granted by implication or otherwise.
Installation
Tighten the gauge by using the wrench on hex
fitting only. Do not tighten it by turning housing!
Use fittings designed for the pressure range of
the gauge. Do not apply vacuum to gauges not
designed for vacuum operation.
Operation
Press the round button on the front of the gauge
to activate the display. The gauge will stay on for
5 minutes. After this time, the gauge will
automatically shut off. The gauge can be shut off
at any time by pressing the button again.
“LOBAT” will appear in the upper left-hand corner
of the display when the battery voltage falls
sufficiently. The battery should be replaced soon
after the LOBAT indicator comes on or unreliable
readings may result.
Calibration
Remove the calibration potentiometer cover on
the front of the unit to access the Zero and Span
controls. The Zero and Span controls are non-
interactive. The gauge port must be open to the
ambient with no pressure or vacuum applied.
Adjust the Zero control until the gauge reads zero
with the minus (–) sign occasionally flashing.
Span calibration should only be attempted if the
user has access to a pressure reference of known
accuracy. The accuracy of the calibration
equipment ideally should be at least four times
the gauge accuracy. Zero calibration must be
done before span calibration. Record readings at
three to five points over the range of gauge and
adjust span control to minimize error and meet
specifications.
Battery Replacement
Remove the six phillips head screws on the back
of the unit. Carefully remove batteries from the
holders by lifting up the positive end of the
battery (opposite the spring). Take care not to
bend or distort the battery retention springs. DO
NOT discard the old battery into fire, any other
sources of extreme heat, or in any other
hazardous manner. Always replace both batteries
at the same time with high quality alkaline
batteries. Observe the polarity of the batteries
when replacing them. The negative (flat) end of
each battery should be inserted first and should
face the spring in the battery holder. Replace the
back cover, including the rubber sealing gasket.
PRESSURE RANGE AND RESOLUTION SPECIFICATIONS
SDPGB SERIES ELECTRICAL CHARACTERISTICS
DIGITAL PRESSURE GAUGE CHARACTERISTICS
Environmental Specifications
Storage temperature –40° to +95°C
Operating temperature –20° to +85°C
Compensated temperature to +70°C
Mechanical Specifications
Size
3.38"W x 2.88"H x 1.65"D
(not including pressure fitting)
Add approximately 0.75" to height for pressure fitting
Weight (approximate)
Gauge: 9 ounces
Shipping weight: 1 pound
Material & Color
Extruded aluminum case, epoxy powder coated
Polycarbonate cover, front and rear gaskets
Light gray body, light gray/blue front
Pressure/Vacuum Connection and Material
1/4" NPT male, 316 stainless steel
Media Compatibility
All wetted parts are 316 SS
Compatible with most liquids and gases
Characteristic
Accuracy ±0.25% of full scale ±1 least significant
(linearity, hysteresis, repeatability) digit typical
Temperature Stability ±1% FS for offset and span,
(relative to 25°C) 0 to 70°C typical
Display 3 readings per second nominal
(update rate, type, size) display update rate
3-1/2 digit LCD, 1/2" digit height
Controls & Location Front-accessible potentiometers,
non-interactive zero and span
Front push button turns gauge on or off.
When on auto shut-off timer starts
Auto Shut-off Time 5 minutes
Battery and Battery Life Two AA alkaline, approx. 2500 hours
Low Battery Indication “LOBAT” on display when battery
must be replaced
Rated Rated
Pressure Proof Burst
SenSym ICT Part No. Range Resolution Pressure Pressure
SDPGB-30+100PG5 -30.0 inHg/100.0 psig 0.1 psig 2x 4x
SDPGB0015PG5 15.0 psig 0.01 psig 2x 4x
SDPGB0030PG5 30.0 psig 0.1 psig 2x 4x
SDPGB0100PG5 100.0 psig 0.1 psig 2x 4x
SDPGB0200PG5 199.9 psig 0.1 psig 2x 4x
SDPGB0300PG5 300 psig 1 psig 2x 4x
SDPGB0500PG5 500 psig 1 psig 2x 4x
SDPGB1000PG5 1000 psig 1 psig 2x 4x