LCM1500W-T-4 - Artesyn Embedded Technologies

POWER

LCM1500

1500 Watt Bulk Front End

Total Power: 1500 W

# of Outputs: Single

Outputs: 12 to 48 V

Optional 5.0 V standby

SPECIAL FEATURES

1500 W output power

Low cost

2.5” x 5.2” x 10.0”

12 Watts per cubic inch

Industrial/Medical safety

-40 °C to 70 °C with derating

Optional 5 V @ 2 A

housekeeping

High efciency: 89% typical

Variable speed “Smart Fans”

DSP controlled

Conformal coat option

± 10% adjustment range

Margin programming

OR-ing FET

COMPLIANCE

EMI Class A

EN61000 Immunity

RoHS 2

SAFETY

ULcUL Recognized ITE

(UL60950-1)

ULcUL Recognized Medical

(ANSI/AAMI ES60601-1)

TUV-SuD ITE + Medical

(EN60950-1 and EN60601-1)

CE LVD (EN60950-1 + ROHS)

BSMI

CB Report

- through Demko for IEC60950-1

- through TUV-SuD for

IEC60601-1

Electrical Specications

Input

Input ra nge 90 - 264 Vac (Operating)

115/230 Vac (Nominal)

TERMINAL BLOCK

Frequency 47 - 440 Hz, Nominal 50/60

Input fusing Internal 20 A fuses, both lines fused

Inrush current ≤ 25 A peak, either hot or cold start

Power factor 0.99 typical, meets EN61000-3-2

Harmonics Meets IEC 1000-3-2 requirements

Input current 18 A RMS max input current, at 100 Vac

Hold up time 20 ms minimum for Main O/P, at full rated load

Efciency > 91% typical at full load / 230 Vac nominal

Leakage current < 0.4 mA at 264 Vac

ON/OFF power switch N/A

Power line transient MOV directly after the fuse

Isolation PRI-Chassis 2500 Vdc Basic

PRI-SEC 4000 VAC Reinforced 2xMOPP

SEC-Chassis 500 Vdc

LCM1500Q Efciency Without the 5 Vsb

76.00

78.00

80.00

82.00

84.00

86.00

88.00

90.00

92.00

25 50 75 100

Loading %

Efciency %

100 Vac

230 Vac

Data Sheet

LCM1500 Data Sheet

Environmental Specications

Operating temperature: -40 °C to +70 °C, linear derating to 50% from 50 °C to 70 °C

Storage temperature: -40 °C to +85 °C

Humidity: 20 to 90%, non-condensing. Operating. Conformal coat option available

Fan noise: < 45 dBA, 80% load at 30

Altitude: Operating - 16,405 feet (3000m)

Storage - 30,000 feet

Shock: MIL-STD-810F 516.5, Procedure I, VI. Storage

Vibration: MIL-STD-810F 514.5, Cat. 4, 10. Storage

Electrical Specications

Output

Output rating: See table 1 90 - 264 Vac

Set point: ± 0.5% 90 - 264 Vac

Total regulation range: Main output ± 2%

5 Vsb ± 1%

Combined line/load/transient when measured at output

terminal

Rated load: 1500 W maximum Derate linear to 50% from 50 °C to 70 °C

Minimum load: Main output @ 0.0 A

5 Vsb @ 0.0 A

No loss of regulation

Output noise (PARD): 1% max p-p

50 mV max p-p

Main output

5 Vsb output

Measured with a 0.1 µF Ceramic and 10 µF Tantalum

Capacitor on any output, 20 MHz

Output voltage overshoot: No overshoot/undershoot outside the regulation band during

on or off cycle

Transient response: < 300 µSec 50% load step @ 1 A/µs

Step load valid between 10% to 100% of output rating

Recovery time to within 1% of set point at onset of transient

Max units in parallel: Up to 10

Short circuit protection: Protected, no damage to occur Bounce mode

Remote sense: Compensation up to 500 mV

Output isolation: Standard per safety requirements

Forced load sharing: To within 10% of all shared outputs Analog sharing control

Overload protection (OCP): 105% to 125%

120% to 170%

Main output

5 Vsb output

Overvoltage protection (OVP): 125% to 145%

110% to 125%

12 V output

5 Vsb output

Overtemp protection: 10 - 15 °C above safe operating area Both PFC and output converter monitored

LCM1500 Data Sheet

Pin Assignment

Signals Name Description Pin Number(s)

+Vout Power rail SK4

GND Power GND SK5

Signals Name Description SK2 Pin Number

A2 EEPROM Address 1

-VPROG Return connection of external supply for Margin Programming 2

A1 EEPROM Address 3

-Vsense Remote Sense Return 4

ISHARE Load share voltage 5

A0 EEPROM Address 6

SDA1 Serial Data Signal (I2C) 7

+VPROG Positive connection of external supply for Margin Programming 8

SCL1 Serial Clock Signal (I2C) 9

+Vsense Remote Sense Positive 10

5VSB 5V standby 11

GND 5V standby Return 12

5VSB 5V standby 13

G_DCOK_C Global DCOK Collector 14

GPIOA6 EEPROM Write Protect 15

G_DCOK_E Global DCOK Emitter (GND) 16

GND Return Ground for output signal and I2C communication 17

G_ACOK_C Global ACOK Collector 18

INH_EN Turn Off Main Output 19

G_ACOK_E Global ACOK Emitter (GND) 20

Note: Mating connector for SK2 is LANDWIN CI0120P1HD0-LF

LED INDICATORS

2 provided are clearly visible up to a 45 degree offset from vertical with ofce environment ambient lighting. The status is reected in the

indicator color.

The DC_OK LED shall light green if the DC output is within specication, and shall be off if the output falls out of specication.

The AC_OK LED is green if the AC is within specication and off when out of specication.

CONTROL SIGNALS

AC_OK Open collector 0.5 V maximum at 10 mA. Both emitter and collector access provided.

DC_OK Open collector 0.5 V maximum at 10 mA. Both emitter and collector access provided.

PS_INHIBIT/ENABLE Signal 0.0 - 0.5 V contact closure, output OFF

PSU Front View (24V & 48V UNITS) Signal Output Signal Connectors (SK2)

LCM1500 Data Sheet

Ordering Information Table 2

LCMXXXXY - A - B - C - ###

Case Size Input Termination Acoustic Noise Option Codes Hardware Code

1-Phase input where XXXX =

1500 = 2.4” x 5.0” x 10.0”, 1500 W Blank = Standard Blank = No Options Factory Assigned for

Modieed standards

T = Terminal Block 1 = Conformal Coat

Voltage Code Y = 4 = 5 V Standby

Code 5 = Opt 1 + 4

L 12

N 15

Q 24

U 36

W 48

Ordering Information Table 1

Model

Number* Output

Nominal Output

Voltage Set Point

Set Point

Tolerance Adjustment Range

Current Output Ripple

P/P (0-50 ˚C)

Max Continuous

Power

Combined Line/

Load Regulation

Min Max

LCM1500L 12 V 12 V ±0.5% 10.8 - 13.2 V 0 A 133 A 120 mV 1500 W 2%

LCM1500N 15 V 15 V ±0.5% 13.5 - 16.5 V 0 A 100 A 150 mV 1500 W 2%

LCM1500Q 24 V 24 V ±0.5% 21.6 - 26.4 V 0 A 67 A 240 mV 1500 W 2%

LCM1500U 36 V 36 V ±0.5% 32.4 - 39.6 V 0 A 43 A 360 mV 1500 W 2%

LCM1500W 48 V 48 V ±0.5% 43.2 - 52.8 V 0 A 33 A 480 mV 1500 W 2%

Mechanical Drawings (LCM1500Q-T, LCM1500U-T and LCM1500W-T)

MOUNTING LOCATIONS SCREW

PENETRATION DEPTH IS 4.6 mm MAX.

RECOMMENDED SCREW TORQUE:

M3.5 x 0.6P = 6 - 8kgf-cm

M4.0 x 0.7P = 8 - 10kgf-cm

LCM1500 Data Sheet

Mechanical Drawings (LCM1500L-T and LCM1500N-T)

Notes:

1. Parts must be completely assembled.

2. For label printing details, refer to ips.

3. Quality controlled dimensions. These dimensions to be included in the mechanical cpk of 1.33

4. Casing parts used must have matching color. In order to ensure color matching of parts, it is required that the raw material that will be processed by the fabricator will come from the same supplier and the

sheetmetal fabricator for all matching parts must be the same. To avoid color variations on the same lot delivered, all parts with matching color requirement should be delivered as a set by the fabricator.

5. Sheared edges visible to the customer should have no rust formation. If rust formation is present then a concealing layer of silver ink or some other substitute should be applied on the rusted area.

6. Mounting locations screw penetration depth is 4.6Mm max.

7. Recommended screw torque:

M3.5X0.6P = 6-8kgf-cm

M4.0X0.7P = 8-10kfg-cm

8. Input: terminal block type. M4 screw torque value of 16kgf-cm using wire gauge 18-10 (13mm centers)

9. Suitable mating connectors:

9.1 For sk2:

A) 764-002569-0000 mat-kit hsg-20way (landwin)

451-004792-0000 Hsg-dr 20ckt (lwe pn: 2050s2000)

451-000709-0000 Crimp term (lwe pn: 2053t021v)

B) 764-003275-0000 mat-kit hsg-20way (civilux)

451-004793-0000 Hsg-20way (cx pn: ci0120sd000)

451-000703-0000 Term-#22~28 (cx pn: ci01td21pe0)

LED (DC OK/FAIL)

LED (AC OK)

SK2 SIGNAL CONNECTOR

(REFER TO IPS)

POS(+) SK3

NEG(-) SK4

TRIMPOT

(12X)M4 MOUNTING HOLES

RECOMMEND TO USE M4X6 SCREW ON

A 2mm THICK PANEL

BRAND LOGO

INPUT (TERMINAL BLOCK)

NOTE 8

132±1

(17,5)

(52,3)

61,7±1

(25,6)

(45,6)

39,1±1

254±1

(2X)

BLADE WIDTH

20 0,5

(2X)

BLADE THICKNESS

4 0,15

(2X)21 0,3

(2X)111 0,3

(2X)44,7 0,3

(2X)216,2 0,3

(2X)16,3 0,3

(2X)54,3 0,3

(2X)44,7 0,3

(2X)216,2 0,3

19,2±1 (254)

LCM1500 Data Sheet

WORLDWIDE OFFICES

Americas

2900 S.Diablo Way

Tempe, AZ 85282

USA

+1 888 412 7832

Europe (UK)

Waterfront Business Park

Merry Hill, Dudley

West Midlands, DY5 1LX

United Kingdom

+44 (0) 1384 842 211

Asia (HK)

14/F, Lu Plaza

2 Wing Yip Street

Kwun Tong, Kowloon

Hong Kong

+852 2176 3333

For more information: www.artesyn.com/power

For support: productsupport.ep@artesyn.com

While every precaution has been taken to ensure accuracy and completeness in this literature, Artesyn

Embedded Technologies assumes no responsibility, and disclaims all liability for damages resulting from use

of this information or for any errors or omissions. Artesyn Embedded Technologies, Artesyn and the Artesyn

Embedded Technologies logo are trademarks and service marks of Artesyn Embedded Technologies, Inc.

All other names and logos referred to are trade names, trademarks, or registered trademarks of their respective

www.artesyn.com

LCM1500 DS 26Feb2015

Accessories

Miscellaneous Specications

BURN-IN

100% Burn-in at 45 °C, at 80 - 90 % load. Duration of burn-in determined by Quality Assurance Procedures.

MTBF

The power supply has a minimum MTBF of 300K hours using the Bell core 332, issue 6 specication @ 25 °C and 40 °C, ambient, at full

load. With the power supply installed in a system in a 25 °C ambient environment and operating at full load, capacitor life shall be 10 years,

minimum for ALL electrolytic capacitors contained within this power supply. The power supply shall demonstrate a MTBF level of

> 500,000 hours.

QUALITY ASSURANCE

Full QAV testing shall be conducted in accordance with Artesyn Embedded Technologies Standards with reports available upon request.

WARRANTY

Artesyn Embedded Technologies shall warrant the power supply to be free of defects in materials and workmanship for a minimum period

of three years from the date of shipment, when operated within specications. The warranty shall be fully transferable to the end owner of

the equipment powered by the supply.

Order kit part number 73-788-001 for control connector interface with .3m wires attached

Order kit part number 73-788-002 for control connector interface with unloaded housing and 20 pins

PIN 20

PIN 2

PIN 19

PIN 1

PIN 3

300 ± 5 mm

PIN 20

PIN 2

PIN 19

PIN 1

PIN 3