1
Date: 6/2/04 SP3223EB/3243EB +3.0V to +5.5V RS-232 Transceivers © Copyright 2004 Sipex Corporation
SP3223EB/3243EB
Intelligent +3.0V to +5.5V RS-232 Transceivers
The SP3223EB and SP3243EB products are RS-232 transceiver solutions intended for
portable or hand-held applications such as notebook and palmtop computers. The SP3223EB
and SP3243EB use an internal high-efficiency, charge-pump power supply that requires only
0.1µF capacitors in 3.3V operation. This charge pump and Sipex's driver architecture allow
the SP3223EB/3243EB series to deliver compliant RS-232 performance from a single power
supply ranging from +3.0V to +5.5V. The SP3223EB is a 2-driver/2-receiver device, and the
SP3243EB is a 3-driver/5-receiver device ideal for laptop/notebook computer and PDA
applications. The SP3243EB includes one complementary receiver that remains alert to
monitor an external device's Ring Indicate signal while the device is shutdown.
The AUTO ON-LINE® feature allows the device to automatically "wake-up" during a shutdown
state when an RS-232 cable is connected and a connected peripheral is turned on. Otherwise,
the device automatically shuts itself down drawing less than 1µA.
■ Meets true EIA/TIA-232-F Standards
from a +3.0V to +5.5V power supply
■ Interoperable with EIA/TIA-232 and
adheres to EIA/TIA-562 down to a +2.7V
power source
■ AUTO ON-LINE® circuitry automatically
wakes up from a 1µA shutdown
■ Minimum 250kbps data rate under load
■ Regulated Charge Pump Yields Stable
RS-232 Outputs Regardless of VCC
Variations
■ Enhanced ESD Specifications:
+15kV Human Body Model
+15kV IEC1000-4-2 Air Discharge
+8kV IEC1000-4-2 Contact Discharge
DESCRIPTION
SELECTION TABLE
Applicable U.S. Patents - 5,306,954; and other patents pending.
eciveDseilppuSrewoP232-SR
srevirD
232-SR
srevieceR
lanretxE
stnenopmoC
ENIL-NOOTUA
®
yrtiucriC
etatS-3LTTfo.oN
sniP
BE3223PSV5.5+otV0.3+22sroticapac4SEYSEY02
BE3423PSV5.5+otV0.3+35sroticapac4SEYSEY82
®
V-
1
2
3
417
18
19
20
5
6
7
16
15
14
SHUTDOWN
C1+
V+
C1-
C2+
C2-
ONLINE
EN
R
1
IN
GND
V
CC
T
1
OUT
STATUS
8
9
10 11
12
13
R
2
IN
R
2
OUT
SP3223EB
T
2
OUT T
1
IN
T
2
IN
R
1
OUT
Now Available in Lead Free Packaging
Date: 6/2/04 SP3223EB/3243EB +3.0V to +5.5V RS-232 Transceivers © Copyright 2004 Sipex Corporation
2
PARAMETER MIN. TYP. MAX. UNITS CONDITIONS
DC CHARACTERISTICS
Supply Current, 1.0 10 µAAll RxIN open, ONLINE = GND,
AUTO ON-LINE®SHUTDOWN = VCC, TxIN = VCC or
GND,VCC = +3.3V, TAMB = +25°C
Supply Current, Shutdown 1.0 10 µASHUTDOWN = GND,
VCC = +3.3V, TAMB = +25°C,
TxIN = VCC or GND
Supply Current, 0.3 1.0 mA ONLINE = SHUTDOWN = VCC,
AUTO ON-LINE® Disabled TxIN = VCC or GND,
no load, VCC = +3.3V, TAMB = +25°C
LOGIC INPUTS AND RECEIVER OUTPUTS
Input Logic Threshold VCC = +3.3V or +5.0V, TxIN,
LOW GND 0.8 V EN (SP3223EB), ONLINE,
HIGH 2.4 VCC V SHUTDOWN
Input Leakage Current ±0.01 ±1.0 µATxIN, EN (SP3223EB), ONLINE,
SHUTDOWN,
TAMB = +25°C, VIN = 0V to VCC
Output Leakage Current ±0.05 ±10 µAReceivers disabled, VOUT = 0V to
VCC
Output Voltage LOW 0.4 V IOUT = 1.6mA
Output Voltage HIGH VCC - 0.6 VCC - 0.1 V IOUT = -1.0mA
DRIVER OUTPUTS
Output Voltage Swing ±5.0 ±5.4 V All driver outputs loaded with 3KΩ
to GND, TAMB = +25°C
Output Resistance 300 ΩVCC = V+ = V- = 0V, VOUT = ±2V
Output Short-Circuit Current ±35 ±60 mA VOUT = 0V
Output Leakage Current ±25 µAV
CC = 0V or 3.0V to 5.5V,
VOUT = ±12V, Drivers disabled
NOTE 1: V+ and V- can have maximum magnitudes of 7V, but their absolute difference cannot exceed 13V.
ABSOLUTE MAXIMUM RATINGS
These are stress ratings only and functional operation
of the device at these ratings or any other above those
indicated in the operation sections of the specifications
below is not implied. Exposure to absolute maximum
rating conditions for extended periods of time may
affect reliability and cause permanent damage to the
device.
VCC ...................................................... -0.3V to +6.0V
V+ (NOTE 1) ...................................... -0.3V to +7.0V
V- (NOTE 1) ....................................... +0.3V to -7.0V
V+ + |V-| (NOTE 1) ........................................... +13V
ICC (DC VCC or GND current) ......................... +100mA
Input Voltages
TxIN, ONLINE,
SHUTDOWN, EN (SP3223E)............ -0.3V to +6.0V
RxIN .................................................................. +25V
Output Voltages
TxOUT ........................................................... +13.2V
RxOUT, STATUS ..................... -0.3V to (VCC + 0.3V)
Unless otherwise noted, the following specifications apply for VCC = +3.0V to +5.5V with TAMB = TMIN to TMAX,
C1 - 4 = 0.1µF. Typical values apply at VCC = +3.3V or +5.0V and TAMB = 25°C.
ELECTRICAL CHARACTERISTICS
Short-Circuit Duration
TxOUT .................................................... Continuous
Storage Temperature ...................... -65°C to +150°C
Power Dissipation per package
28-pin PDIP
(derate 16.0mW/°C above+70°C) ...................... 1300mW
20-pin SSOP
(derate 9.25mW/°C above +70°C) ...................... 750mW
20-pin TSSOP
(derate 11.1mW/°C above +70°C) ....................... 900mW
28-pin SOIC
(derate 12.7mW/°C above +70°C) .................... 1000mW
28-pin SSOP
(derate 11.2mW/°C above +70°C) ...................... 900mW
28-pin TSSOP
(derate 11.1mW/°C above +70°C) ....................... 900mW
32-pin QFN
3
Date: 6/2/04 SP3223EB/3243EB +3.0V to +5.5V RS-232 Transceivers © Copyright 2004 Sipex Corporation
ELECTRICAL CHARACTERISTICS
Unless otherwise noted, the following specifications apply for VCC = +3.0V to +5.5V with TAMB = TMIN to TMAX,
C1 - 4 = 0.1µF. Typical values apply at VCC = +3.3V or +5.0V and TAMB = 25°C.
PARAMETER MIN. TYP. MAX. UNITS CONDITIONS
RECEIVER INPUTS
Input Voltage Range -25 25 V
Input Threshold LOW 0.6 1.2 V VCC = 3.3V
Input Threshold LOW 0.8 1.5 V VCC = 5.0V
Input Threshold HIGH 1.5 2.4 V VCC = 3.3V
Input Threshold HIGH 1.8 2.4 V VCC = 5.0V
Input Hysteresis 0.3 V
Input Resistance 3 5 7 kΩ
AUTO ON-LINE® CIRCUITRY CHARACTERISTICS (ONLINE = GND, SHUTDOWN = VCC)
STATUS Output Voltage LOW 0.4 V IOUT = 1.6mA
STATUS Output Voltage HIGH VCC - 0.6 V IOUT = -1.0mA
Receiver Threshold to Drivers
Enabled (tONLINE)200 µsFigure 20
Receiver Positive or Negative 0.5 µsFigure 20
Threshold to STATUS HIGH
(tSTSH)
Receiver Positive or Negative 20 µsFigure 20
Threshold to STATUS LOW
(tSTSL)
TIMING CHARACTERISTICS
Maximum Data Rate 250 kbps RL = 3KΩ, CL = 1000pF,
one driver active
Receiver Propagation Delay
tPHL 0.15 µsReceiver input to Receiver output,
tPLH 0.15 CL = 150pF
Receiver Output Enable Time 200 ns Normal operation
Receiver Output Disable Time 200 ns Normal operation
Driver Skew 100 ns | tPHL - tPLH |, TAMB = 25°C
Receiver Skew 50 ns | tPHL - tPLH |
Transition-Region Slew Rate 30 V/µsV
CC= 3.3V, RL = 3KΩ, TAMB = 25°C,
measurements taken from -3.0V to
+3.0V or +3.0V to -3.0V
Date: 6/2/04 SP3223EB/3243EB +3.0V to +5.5V RS-232 Transceivers © Copyright 2004 Sipex Corporation
4
Figure 1. Transmitter Output Voltage VS. Load
Capacitance for the SP3223EB
Figure 2. Slew Rate VS. Load Capacitance for the
SP3223EB
TYPICAL PERFORMANCE CHARACTERISTICS
Unless otherwise noted, the following performance characteristics apply for VCC = +3.3V, 250kbps data rate, all drivers
loaded with 3KΩ, 0.1µF charge pump capacitors, and TAMB = +25°C.
30
25
20
15
10
5
00 500 1000 2000 3000 4000 5000
Slew rate (V/µs)
Load Capacitance (pF)
- Slew
+ Slew
1 Transmitter at 250Kbps
1 Transmitter at 15.6Kbps
All drivers loaded 3K + Load Cap
35
30
25
20
15
10
5
0
ICC (mA)
Load Capacitance (pF)
01000 2000 3000 4000 5000
250Kbps
125Kbps
20Kbps
1 Transmitter at 250Kbps
1 Transmitter at 15.6Kbps
All drivers loaded 3K + Load Cap
Figure 3. Supply Current VS. Load Capacitance when
Transmitting Data for the SP3223EB
Figure 4. Supply Current VS. Supply Voltage for
the SP3243EB
20
15
10
5
02.7 3 3.5 4 4.5 5
Supply Voltage (V
DC
)
Supply Current (mA)
1 Transmitter at 250Kbps
2 Transmitters at 15.6Kbps
All drivers loaded with 3K // 1000pF
Figure 5. Transmitter Output Voltage VS. Supply
Voltage for the SP3243EB
Figure 6. Transmitter Output Voltage VS. Load
Capacitance for the SP3243EB
6
4
2
0
-2
-4
-6 0 1000 2000 3000 4000 5000
TxOUT +
TxOUT -
Transmitter Output
Voltage (V
DC
)
Load Capacitance (pF)
6
4
2
0
-2
-4
-6 0 1000 2000 3000 4000 5000
TxOUT +
TxOUT -
Transmitter Output
Voltage (V)
Load Capacitance (pF)
6
4
2
0
-2
-4
-6 2.7 3 3.5 4 4.5 5
Supply Voltage (V
DC
)
Transmitter Output
Voltage (V
DC
)
TxOUT -
TxOUT +
5
Date: 6/2/04 SP3223EB/3243EB +3.0V to +5.5V RS-232 Transceivers © Copyright 2004 Sipex Corporation
TYPICAL PERFORMANCE CHARACTERISTICS
Unless otherwise noted, the following performance characteristics apply for VCC = +3.3V, 250kbps data rate, all drivers
loaded with 3KΩ, 0.1µF charge pump capacitors, and TAMB = +25°C.
Figure 7. Slew Rate VS. Load Capacitance for the
SP3243EB
25
20
15
10
5
00500 1000 2000 3000 4000 5000
Slew rate (V/µs)
Load Capacitance (pF)
- Slew
+ Slew
1 Transmitter at 250Kbps
2 Transmitter at 15.6Kbps
All drivers loaded 3K + Load Cap
Figure 8. Supply Current VS. Load Capacitance when
Transmitting Data for the SP3243EB
40
35
30
25
20
15
10
5
0
Supply Current (mA)
Load Capacitance (pF)
0 1000 2000 3000 4000 5000
250Kbps 120Kbps
20Kbps
1 Transmitter at full Data Rate
2 Transmitters at 15.5 Kbps
All Transmitters loades 3K + Load Cap
6
4
2
0
-2
-4
-6 2.7 3 3.5 4 4.5 5
Supply Voltage (V
DC
)
Transmitter Output
Voltage (V)
TxOUT -
TxOUT +
Figure 9. Supply Current VS. Supply Voltage for the
SP3243EB
Figure 10. Transmitter Output Voltage VS. Supply
Voltage for the SP3243EB
25
20
15
10
5
0
2.7 3 3.5 4 4.5 5
Supply Voltage (V
DC
)
Supply Current (mA)
1 Transmitter at 250Kbps
2 Transmitters at 15.6Kbps
All drivers loaded with 3K // 1000pF
Date: 6/2/04 SP3223EB/3243EB +3.0V to +5.5V RS-232 Transceivers © Copyright 2004 Sipex Corporation
6
Table 1. Device Pin Description
PIN NUMBER
SP3243EB
SOIC, SSOP, SP3243EBCR
NAME FUNCTION SP3223EB TSSOP QFN
EN Receiver Enable. Apply logic LOW for normal operation. 1 - -
Apply logic HIGH to disable the receiver outputs (high-Z state).
C1+ Positive terminal of the voltage doubler charge-pump capacitor. 2 28 28
V+ Regulated +5.5V output generated by the charge pump. 3 27 26
C1- Negative terminal of the voltage doubler charge-pump capacitor. 4 24 22
C2+ Positive terminal of the inverting charge-pump capacitor. 5 1 29
C2- Negative terminal of the inverting charge-pump capacitor. 6 2 31
V- Regulated -5.5V output generated by the charge pump. 7 3 32
R1IN RS-232 receiver input. 16 4 2
R2IN RS-232 receiver input. 9 5 3
R3IN RS-232 receiver input. - 6 4
R4IN RS-232 receiver input. - 7 5
R5IN RS-232 receiver input. - 8 6
R1OUT TTL/CMOS receiver output. 15 19 17
R2OUT TTL/CMOS receiver output. 10 18 16
R2OUT Non-inverting receiver-2 output, active in shutdown. - 20 18
R3OUT TTL/CMOS receiver output. - 17 15
R4OUT TTL/CMOS receiver output. - 16 14
R5OUT TTL/CMOS receiver output. - 15 13
STATUS TTL/CMOS Output indicating online and shutdown status. 11 21 19
T1IN TTL/CMOS driver input. 13 14 12
T2IN TTL/CMOS driver input. 12 13 11
T3IN TTL/CMOS driver input. - 12 10
ONLINE Apply logic HIGH to override Auto-Online circuitry keeping 14 23 21
drivers active (SHUTDOWN must also be logic HIGH,
refer to Table 2).
T1OUT RS-232 driver output. 17 9 7
T2OUT RS-232 driver output. 8 10 8
T3OUT RS-232 driver output. - 11 9
GND Ground. 18 25 23
VCC +3.0V to +5.5V supply voltage. 19 26 25
SHUTDOWN Apply logic LOW to shut down drivers and charge pump. 20 22 20
This overrides all AUTO ON-LINE® circuitry and ONLINE
(refer to Table 2).
NC No Connection - - 1,24,27,30
7
Date: 6/2/04 SP3223EB/3243EB +3.0V to +5.5V RS-232 Transceivers © Copyright 2004 Sipex Corporation
Figure 12. SP3243EB Pinout Configuration
Figure 11. SP3223EB Pinout Configuration
V-
1
2
3
417
18
19
20
5
6
7
16
15
14
SHUTDOWN
C1+
V+
C1-
C2+
C2-
ONLINE
EN
R
1
IN
GND
VCC
T
1
OUT
STATUS
8
9
10 11
12
13
R
2
IN
R
2
OUT
SP3223EB
T
2
OUT T
1
IN
T
2
IN
R
1
OUT
R
4
IN
1
2
3
425
26
27
28
5
6
7
24
23
22 SHUTDOWN
C2-
V-
R
1
IN
R
2
IN
R
3
IN ONLINE
C2+
C1-
GND
V
CC
V+
STATUS
T
1
IN
8
9
10
11 18
19
20
21
12
13
14
17
16
15 R
5
OUT
T
1
OUT
T
2
OUT
T
3
OUT
T
3
IN
T
2
IN R
4
OUT
R
5
IN
R
3
OUT
R
2
OUT
R
1
OUT
R
2
OUT
SP3243EB
C1+
Figure 13. SP3243EB QFN (QFN) Pinout Configuration
®
®
SP3243EB
V-
C2-
NC
C2+
C1+
NC
V+
V
CC
NC
R
1
IN
R
2
IN
R
3
IN
R
4
IN
R
5
IN
T
1
OUT
T
2
OUT
T
3
OUT
T
3
IN
T
2
IN
T
1
IN
R
5
OUT
R
4
OUT
R
3
OUT
R
2
OUT
1
2
3
4
5
6
7
8
24
23
22
21
20
19
18
17
9
10
11
12
13
14
15
16
32
31
30
29
28
27
26
25
NC
GND
C1-
ONLINE
SHUTDOWN
STATUS
R
2
OUT
R
1
OUT
Date: 6/2/04 SP3223EB/3243EB +3.0V to +5.5V RS-232 Transceivers © Copyright 2004 Sipex Corporation
8
Figure 14. SP3223EB Typical Operating Circuit
SP3223EB
2
4
6
5
3
7
19
GND
T
1
IN
T
2
IN
C1+
C1-
C2+
C2-
V+
V-
V
CC
13
12
0.1µF
0.1µF
0.1µF
+
C2
C5
C1
+
+C3
C4
+
+
0.1µF
0.1µF
17
8
RS-232
OUTPUTS
RS-232
INPUTS
TTL/CMOS
INPUTS
+3.3V to +5V
18
SHUTDOWN
20
5kΩ
R
1
OUT
15 16
5kΩ
R
2
IN
R
2
OUT
10 9
TTL/CMOS
OUTPUTS
EN
1
ONLINE
14
R
1
IN
T
2
OUT
T
1
OUT
11 STATUS
V
CC
To µP Supervisor
Circuit
9
Date: 6/2/04 SP3223EB/3243EB +3.0V to +5.5V RS-232 Transceivers © Copyright 2004 Sipex Corporation
Figure 15. SP3243EB Typical Operating Circuit
SP3243EB
28
24
2
1
27
3
26
5kΩ
5kΩ
5kΩ
5kΩ
5kΩ
GND
C1+
C1-
C2+
C2-
V+
V-
V
CC
14
13
12
20
19
18
17
16
15
0.1µF
0.1µF
0.1µF
+
C2
C5
C1
+
+C3
C4
+
+
0.1µF
0.1µ
F
9
10
11
4
5
6
7
8
RS-232
OUTPUTS
RS-232
INPUTS
TTL/CMOS
INPUTS
TTL/CMOS
OUTPUTS
To µP Supervisor
Circuit
23
22
21
V
CC
V
CC
25
T
1
IN
R
1
OUT R
1
IN
T
2
OUT
R
2
OUT
T
2
IN
T
3
IN T
3
OUT
T
1
OUT
R
2
IN
R
3
IN
R
4
IN
R
5
IN
R
2
OUT
R
3
OUT
R
4
OUT
R
5
OUT
ONLINE
SHUTDOWN
STATUS
Date: 6/2/04 SP3223EB/3243EB +3.0V to +5.5V RS-232 Transceivers © Copyright 2004 Sipex Corporation
10
DESCRIPTION
The SP3223EB and SP3243EB transceivers meet
the EIA/TIA-232 and ITU-T V.28/V.24 com-
munication protocols and can be implemented
in battery-powered, portable, or hand-held ap-
plications such as notebook or palmtop comput-
ers. The SP3223EB and SP3243EB devices
feature Sipex's proprietary and patented (U.S.--
5,306,954) on-board charge pump circuitry that
generates ±5.5V RS-232 voltage levels from a
single +3.0V to +5.5V power supply. The
SP3223EB and SP3243EB devices can operate
at a data rate of 250kbps fully loaded.
The SP3223EB is a 2-driver/2-receiver device,
and the SP3243EB is a 3-driver/5-receiver de-
vice ideal for portable or hand-held applications.
The SP3243EB includes one complementary
always-active receiver that can monitor an
external device (such as a modem) in shutdown.
This aids in protecting the UART or serial
controller IC by preventing forward biasing
of the protection diodes where VCC may be
disconnected.
The SP3223EB and SP3243EB series is an ideal
choice for power sensitive designs. The
SP3223EB and SP3243EB devices feature
AUTO ON-LINE® circuitry which reduces the
power supply drain to a 1µA supply current. In
many portable or hand-held applications, an RS-
232 cable can be disconnected or a connected
peripheral can be turned off. Under these condi-
tions, the internal charge pump and the drivers
will be shut down. Otherwise, the system auto-
matically comes online. This feature allows de-
sign engineers to address power saving concerns
without major design changes.
THEORY OF OPERATION
The SP3223EB and SP3243EB series is made up
of four basic circuit blocks:
1. Drivers,
2. Receivers,
3. the Sipex proprietary charge pump, and
4. AUTO ON-LINE® circuitry.
Drivers
The drivers are inverting level transmitters that
convert TTL or CMOS logic levels to 5.0V EIA/
TIA-232 levels with an inverted sense relative to
the input logic levels. Typically, the RS-232
output voltage swing is +5.4V with no load and
+5V minimum fully loaded. The driver outputs
are protected against infinite short-circuits to
ground without degradation in reliability. These
drivers comply with the EIA-TIA-232F and all
previous RS-232 versions. Unused driver inputs
should be connected to GND or VCC.
The drivers can guarantee a data rate of 250kbps
fully loaded with 3kΩ in parallel with 1000pF,
ensuring compatibility with PC-to-PC commu-
nication software.
The slew rate of the driver output is internally
limited to a maximum of 30V/µs in order to
meet the EIA standards (EIA RS-232D 2.1.7,
Paragraph 5). The transition of the loaded
output from HIGH to LOW also meets the
monotonicity requirements of the standard.
Figure 16. Interface Circuitry Controlled by Micropro-
cessor Supervisory Circuit
SP3243EB
28
24
2
1
27
3
26
5KΩ
5KΩ
5KΩ
5KΩ
5KΩ
GND
C1+
C1-
C2+
C2-
V+
V-
VCC
14
13
12
20
19
18
17
16
15
0.1µF
0.1µF
0.1µF
+
C2
C5
C1
+
+C3
C4
+
+
0.1µF
0.1µF
9
10
11
4
5
6
7
8
RS-232
OUTPUTS
RS-232
INPUTS
23
22
21
VCC
25
T
1
IN
R
1
OUT R
1
IN
T
2
OUT
R
2
OUT
T
2
IN
T
3
IN T
3
OUT
T
1
OUT
R
2
IN
R
3
IN
R
4
IN
R
5
IN
R
2
OUT
R
3
OUT
R
4
OUT
R
5
OUT
ONLINE
SHUTDOWN
STATUS
UART
or
Serial C
P
Supervisor
IC
TxD
RTS
DTR
RxD
CTS
DSR
DCD
RI
VCC
VIN
RESET
11
Date: 6/2/04 SP3223EB/3243EB +3.0V to +5.5V RS-232 Transceivers © Copyright 2004 Sipex Corporation
The SP3223EB and SP3243EB drivers can main-
tain high data rates up to 250kbps fully loaded.
Figure 17. shows a loopback test circuit used to
test the SP3243EB RS-232 Drivers. Figure 18
shows the test results of the loopback circuit with
all three drivers active at 120kbps with typical
RS-232 loads in parallel with 1000pF capacitors.
Figure 19 shows the test results where one driver
Table 2. SHUTDOWN and EN Truth Tables
Note: In AUTO ON-LINE® Mode where ONLINE =
GND and SHUTDOWN = VCC, the device will shut down
if there is no activity present at the Receiver inputs.
Figure 17. Loopback Test Circuit for RS-232 Driver
Data Transmission Rates
was active at 250kbps and all three drivers loaded
with an RS-232 receiver in parallel with a 1000pF
capacitor. A solid RS-232 data transmission
rate of 250kbps provides compatibility with many
designs in personal computer peripherals and
LAN applications.
Receivers
The receivers convert ±5.0V EIA/TIA-232
levels to TTL or CMOS logic output levels. All
receivers have an inverting output that can be
disabled by using the EN pin.
Figure 18. Loopback Test Circuit All Drivers at 120kbps Figure 19. Loopback Test Circuit One Driver at 250kbps
SP3223EB
SP3243EB
GND
T
1
IN
T
X
IN
C1+
C1-
C2+
C2-
V+
V-
V
CC
0.1µF
0.1µF
0.1µF
+
C2
C5
C1
+
+C3
C4
+
+
0.1µF
0.1µF
TTL/CMOS
INPUTS
+3V to +5V
18
SHUTDOWN
5kΩ
R
1
OUT
5kΩ
R
X
IN
R
X
OUT
TTL/CMOS
OUTPUTS
EN
ONLINE
R
1
IN
T
X
OUT
T
1
OUT
STATUS
V
CC
To µP Supervisor
Circuit
1000pF 1000pF
DEVICE: SP3223EB
SHUTDOWN EN TXOUT RXOUT
00High Z Active
01High Z High Z
10Active Active
11Active High Z
DEVICE: SP3243EB
SHUTDOWN TXOUT RXOUT R2OUT
0High Z High Z Active
1Active Active Active
Date: 6/2/04 SP3223EB/3243EB +3.0V to +5.5V RS-232 Transceivers © Copyright 2004 Sipex Corporation
12
Receivers are active when the AUTO ON-LINE®
circuitry is enabled or when in shutdown.
During the shutdown, the receivers will continue
to be active. If there is no activity present at the
receivers for a period longer than 100µs or when
SHUTDOWN is enabled, the device goes into a
standby mode where the circuit draws 1µA.
Driving EN to a logic HIGH forces the outputs of
the receivers into high-impedance. The truth
table logic of the SP3223EB and SP3243EB driver
and receiver outputs can be found in Table 2.
The SP3243EB includes an additional non-in-
verting receiver with an output R2OUT. R2OUT
is an extra output that remains active and moni-
tors activity while the other receiver outputs are
forced into high impedance. This allows Ring
Indicator (RI) from a peripheral to be monitored
without forward biasing the TTL/CMOS inputs
of the other devices connected to the receiver
outputs.
Since receiver input is usually from a transmis-
sion line where long cable lengths and system
interference can degrade the signal, the inputs
have a typical hysteresis margin of 300mV. This
ensures that the receiver is virtually immune to
noisy transmission lines. Should an input be left
unconnected, an internal 5KΩ pulldown resistor
to ground will commit the output of the receiver
to a HIGH state.
Charge Pump
The charge pump is a Sipex–patented design
(U.S. 5,306,954) and uses a unique approach
compared to older less–efficient designs. The
charge pump still requires four external
capacitors, but uses a four–phase voltage
shifting technique to attain symmetrical 5.5V
power supplies. The internal power supply
consists of a regulated dual charge pump that
provides output voltages 5.5V regardless of the
input voltage (VCC) over the +3.0V to +5.5V
range. This is important to maintain compliant
RS-232 levels regardless of power supply
fluctuations.
The charge pump operates in a discontinuous
mode using an internal oscillator. If the output
voltages are less than a magnitude of 5.5V, the
charge pump is enabled. If the output voltages
exceed a magnitude of 5.5V, the charge pump is
disabled. This oscillator controls the four phases
of the voltage shifting. A description of each
phase follows.
Phase 1
— VSS charge storage — During this phase of
the clock cycle, the positive side of capacitors
C1 and C2 are initially charged to VCC. Cl+ is
then switched to GND and the charge in C1– is
transferred to C2–. Since C2+ is connected to
VCC, the voltage potential across capacitor C2 is
now 2 times VCC.
Phase 2
— VSS transfer — Phase two of the clock
connects the negative terminal of C2 to the VSS
storage capacitor and the positive terminal of C2
to GND. This transfers a negative generated
voltage to C3. This generated voltage is
regulated to a minimum voltage of -5.5V.
Simultaneous with the transfer of the voltage to
C3, the positive side of capacitor C1 is switched
to VCC and the negative side is connected to
GND.
Phase 3
— VDD charge storage — The third phase of the
clock is identical to the first phase — the charge
transferred in C1 produces –VCC in the negative
terminal of C1, which is applied to the negative
side of capacitor C2. Since C2+ is at VCC, the
voltage potential across C2 is 2 times VCC.
Phase 4
— VDD transfer — The fourth phase of the clock
connects the negative terminal of C2 to GND,
and transfers this positive generated voltage
across C2 to C4, the VDD storage capacitor. This
voltage is regulated to +5.5V. At this voltage,
the internal oscillator is disabled. Simultaneous
with the transfer of the voltage to C4, the
positive side of capacitor C1 is switched to VCC
and the negative side is connected to GND,
allowing the charge pump cycle to begin again.
The charge pump cycle will continue as long as
the operational conditions for the internal
oscillator are present.
13
Date: 6/2/04 SP3223EB/3243EB +3.0V to +5.5V RS-232 Transceivers © Copyright 2004 Sipex Corporation
Since both V+ and V– are separately generated
from VCC, in a no–load condition V+ and V– will
be symmetrical. Older charge pump approaches
that generate V– from V+ will show a decrease in
the magnitude of V– compared to V+ due to the
inherent inefficiencies in the design.
Figure 20. AUTO ON-LINE® Timing Waveforms
RECEIVER
RS-232 INPUT
VOLTAGES
STATUS
+5V
0V
-5V
tSTSL
tSTSH
tONLINE
VCC
0V
DRIVER
RS-232 OUTPUT
VOLTAGES
0V
+2.7V
-2.7V
S
H
U
T
D
O
W
N
The clock rate for the charge pump typically
operates at 250kHz. The external capacitors can
be as low as 0.1µF with a 16V breakdown
voltage rating.
Date: 6/2/04 SP3223EB/3243EB +3.0V to +5.5V RS-232 Transceivers © Copyright 2004 Sipex Corporation
14
Figure 22. Charge Pump — Phase 2
Figure 23. Charge Pump Waveforms
V
CC
= +5V
–10V
V
SS
Storage Capacitor
V
DD
Storage Capacitor
C
1
C
2
C
3
C
4
+
+
++
–
–
––
Figure 24. Charge Pump — Phase 3
V
CC
= +5V
–5V
+5V
–5V
V
SS
Storage Capacitor
V
DD
Storage Capacitor
C
1
C
2
C
3
C
4
+
+
++
–
–
––
Figure 25. Charge Pump — Phase 4
V
CC
= +5V
+10V
V
SS
Storage Capacitor
V
DD
Storage Capacitor
C
1
C
2
C
3
C
4
+
+
++
–
–
––
VCC = +5V
–5V –5V
+5V
VSS Storage Capacitor
VDD Storage Capacitor
C1C2
C3
C4
+
+
++
–
–
––
Figure 21. Charge Pump — Phase 1
Ch1 2.00V Ch2 2.00V M 1.00µs Ch1 1.96V
2
1T
T[]
T
2
+6V
a) C2+
b) C2-
-6V
0V
0V
15
Date: 6/2/04 SP3223EB/3243EB +3.0V to +5.5V RS-232 Transceivers © Copyright 2004 Sipex Corporation
Figure 26. SP3243EB Driver Output Voltages vs. Load
Current per Transmitter
Figure 27. Circuit for the connectivity of the SP3243EB with a DB-9 connector
6
4
2
0
-2
-4
-6
Transmitter Output Voltage [V]
Load Current Per Transmitter [mA]
Vout+
Vout-
0.62
0.869
0.939
1.02
1.12
1.23
1.38
1.57
1.82
2.67
3.46
4.93
8.6
6
7
8
9
1
2
3
4
5
DB-9
Connector
6. DCE Ready
7. Request to Send
8. Clear to Send
9. Ring Indicator
DB-9 Connector Pins:
1. Received Line Signal Detector
2. Received Data
3. Transmitted Data
4. Data Terminal Ready
5. Signal Ground (Common)
SP3243EB
28
24
2
1
27
3
26
5kΩ
5kΩ
5kΩ
5kΩ
5kΩ
GND
C1+
C1-
C2+
C2-
V+
V-
V
CC
14
13
12
20
19
18
17
16
15
0.1µF
0.1µF
0.1µF
+
C2
C5
C1
+
+C3
C4
+
+
0.1µF
0.1µF
9
10
11
4
5
6
7
8
To µP Supervisor
Circuit
23
22
21
V
CC
V
CC
25
T
1
IN
R
1
OUT R
1
IN
T
2
OUT
R
2
OUT
T
2
IN
T
3
IN T
3
OUT
T
1
OUT
R
2
IN
R
3
IN
R
4
IN
R
5
IN
R
2
OUT
R
3
OUT
R
4
OUT
R
5
OUT
ONLINE
SHUTDOWN
STATUS
Date: 6/2/04 SP3223EB/3243EB +3.0V to +5.5V RS-232 Transceivers © Copyright 2004 Sipex Corporation
16
Table 3. AUTO ON-LINE® Logic
Figure 28. Stage I of AUTO ON-LINE® Circuitry
Figure 29. Stage II of AUTO ON-LINE® Circuitry
RS-232
Receiver Block
RXINACT
Inactive Detection Block
RXIN RXOUT
R
1
INACT R
2
INACT R
3
INACT R
4
INACT R
5
INACT
Delay
Stage
Delay
Stage
Delay
Stage
Delay
Stage Delay
Stage
SHUTDOWN
STATUS
RS - 232 SIGNAL SHUTDOWN ONLINE INPUT STATUS OUTPUT TRANCEIVER
AT RECEIVER INPUT STATUS
INPUT
YES HIGH LOW HIGH Normal Operation
(AUTO ON-LINE®)
NO HIGH HIGH LOW Normal Operation
NO HIGH LOW LOW Sutdown
(AUTO ON-LINE® )
YES LOW HIGH/LOW HIGH Shutdown
NO LOW HIGH/LOW LOW Shutdown
17
Date: 6/2/04 SP3223EB/3243EB +3.0V to +5.5V RS-232 Transceivers © Copyright 2004 Sipex Corporation
AUTO ON-LINE® Circuitry
The SP3223EB and SP3243EB devices have a
patent pending AUTO ON-LINE® circuitry on
board that saves power in applications such as
laptop computers, palmtop (PDA) computers,
and other portable systems.
The SP3223EB and SP3243EB devices incorpo-
rate an AUTO ON-LINE® circuit that automati-
cally enables itself when the external transmit-
ters are enabled and the cable is connected.
Conversely, the AUTO ON-LINE® circuit also
disables most of the internal circuitry when the
device is not being used and goes into a standby
mode where the device typically draws 1µA.
This function can also be externally controlled
by the ONLINE pin. When this pin is tied to a
logic LOW, the AUTO ON-LINE® function is
active. Once active, the device is enabled until
there is no activity on the receiver inputs. The
receiver input typically sees at least ±3V, which
are generated from the transmitters at the other
end of the cable with a ±5V minimum. When the
external transmitters are disabled or the cable is
disconnected, the receiver inputs will be pulled
down by their internal 5kΩ resistors to ground.
When this occurs over a period of time, the
internal transmitters will be disabled and the
device goes into a shutdown or standby mode.
When ONLINE is HIGH, the AUTO ON-LINE®
mode is disabled.
The AUTO ON-LINE® circuit has two stages:
1) Inactive Detection
2) Accumulated Delay
The first stage, shown in Figure 28, detects an
inactive input. A logic HIGH is asserted on
RXINACT if the cable is disconnected or the
external transmitters are disabled. Otherwise,
RXINACT will be at a logic LOW. This circuit is
duplicated for each of the other receivers.
The second stage of the AUTO ON-LINE® cir-
cuitry, shown in Figure 29, processes all the
receiver's RXINACT signals with an accumu-
lated delay that disables the device to a 1µA
supply current.
The STATUS pin goes to a logic LOW when the
cable is disconnected, the external transmitters
are disabled, or the SHUTDOWN pin is
invoked. The typical accumulated delay is
around 20µs.
When the SP3223EB and SP3243EB drivers or
internal charge pump are disabled, the supply
current is reduced to 1µA. This can commonly
occur in hand-held or portable applications where
the RS-232 cable is disconnected or the RS-232
drivers of the connected peripheral are turned off.
The AUTO ON-LINE® mode can be disabled by
the SHUTDOWN pin. If this pin is a logic LOW,
the AUTO ON-LINE® function will not operate
regardless of the logic state of the ONLINE pin.
Table 3 summarizes the logic of the AUTO ON-
LINE® operating modes. The truth table logic of
the SP3223EB and SP3243EB driver and re-
ceiver outputs can be found in Table 2.
The STATUS pin outputs a logic LOW signal
if the device is shutdown. This pin goes to a
logic HIGH when the external transmitters are
enabled and the cable is connected.
When the SP3223EB and SP3243EB devices
are shut down, the charge pumps are turned off.
V+ charge pump output decays to VCC, the
V- output decays to GND. The decay time will
depend on the size of capacitors used for the
charge pump. Once in shutdown, the time
required to exit the shut down state and have
valid V+ and V- levels is typically 200µs.
For easy programming, the STATUS can be
used to indicate DTR or a Ring Indicator signal.
Tying ONLINE and SHUTDOWN together
will bypass the AUTO ON-LINE® circuitry so
this connection acts like a shutdown input pin.
Date: 6/2/04 SP3223EB/3243EB +3.0V to +5.5V RS-232 Transceivers © Copyright 2004 Sipex Corporation
18
ESD TOLERANCE
The SP3223EB/3243EB series incorporates
ruggedized ESD cells on all driver output and
receiver input pins. The ESD structure is
improved over our previous family for more
rugged applications and environments sensitive
to electro-static discharges and associated
transients. The improved ESD tolerance is at
least +15kV without damage nor latch-up.
There are different methods of ESD testing
applied:
a) MIL-STD-883, Method 3015.7
b) IEC1000-4-2 Air-Discharge
c) IEC1000-4-2 Direct Contact
The Human Body Model has been the generally
accepted ESD testing method for semiconductors.
This method is also specified in MIL-STD-883,
Method 3015.7 for ESD testing. The premise of
this ESD test is to simulate the human body’s
potential to store electrostatic energy and
discharge it to an integrated circuit. The
simulation is performed by using a test model as
shown in Figure 30. This method will test the
IC’s capability to withstand an ESD transient
during normal handling such as in manufacturing
areas where the ICs tend to be handled frequently.
The IEC-1000-4-2, formerly IEC801-2, is
generally used for testing ESD on equipment and
systems. For system manufacturers, they must
guarantee a certain amount of ESD protection
since the system itself is exposed to the outside
environment and human presence. The premise
with IEC1000-4-2 is that the system is required
to withstand an amount of static electricity when
ESD is applied to points and surfaces of the
equipment that are accessible to personnel during
normal usage. The transceiver IC receives most
of the ESD current when the ESD source is
applied to the connector pins. The test circuit for
IEC1000-4-2 is shown on Figure 31. There are
two methods within IEC1000-4-2, the Air
Discharge method and the Contact Discharge
method.
With the Air Discharge Method, an ESD voltage
is applied to the equipment under test (EUT)
through air. This simulates an electrically charged
person ready to connect a cable onto the rear of
the system only to find an unpleasant zap just
before the person touches the back panel. The
high energy potential on the person discharges
through an arcing path to the rear panel of the
system before he or she even touches the system.
This energy, whether discharged directly or
through air, is predominantly a function of the
discharge current rather than the discharge
voltage. Variables with an air discharge such as
approach speed of the object carrying the ESD
potential to the system and humidity will tend to
change the discharge current. For example, the
rise time of the discharge current varies with the
approach speed.
The Contact Discharge Method applies the ESD
current directly to the EUT. This method was
devised to reduce the unpredictability of the
ESD arc. The discharge current rise time is
constant since the energy is directly transferred
without the air-gap arc. In situations such as
hand held systems, the ESD charge can be directly
discharged to the equipment from a person already
holding the equipment. The current is transferred
on to the keypad or the serial port of the equipment
directly and then travels through the PCB and finally
to the IC.
R
C
C
S
R
S
SW1 SW2
R
C
Device
Under
Test
DC Power
Source
C
S
R
S
SW1 SW2
Figure 30. ESD Test Circuit for Human Body Model
19
Date: 6/2/04 SP3223EB/3243EB +3.0V to +5.5V RS-232 Transceivers © Copyright 2004 Sipex Corporation
DEVICE PIN HUMAN BODY IEC1000-4-2
TESTED MODEL Air Discharge Direct Contact Level
Driver Outputs ±15kV ±15kV ±8kV 4
Receiver Inputs ±15kV ±15kV ±8kV 4
R
S
and
R
V
add up to 330Ω for IEC1000-4-2.
R
S
and
R
V
add up to 330Ω for IEC1000-4-2.
Contact-Discharge Module
R
V
R
C
C
S
R
S
SW1 SW2
R
C
Device
Under
Test
DC Power
Source
C
S
R
S
SW1 SW2
R
V
Contact-Discharge Module
The circuit model in Figures 29 and 30 represent
the typical ESD testing circuit used for all three
methods. The CS is initially charged with the DC
power supply when the first switch (SW1) is on.
Now that the capacitor is charged, the second
switch (SW2) is on while SW1 switches off. The
voltage stored in the capacitor is then applied
through RS, the current limiting resistor, onto the
device under test (DUT). In ESD tests, the SW2
switch is pulsed so that the device under test
receives a duration of voltage.
For the Human Body Model, the current limiting
resistor (RS) and the source capacitor (CS) are
1.5kΩ an 100pF, respectively. For IEC-1000-4-
2, the current limiting resistor (RS) and the source
capacitor (CS) are 330Ω an 150pF, respectively.
The higher CS value and lower RS value in the
IEC1000-4-2 model are more stringent than the
Human Body Model. The larger storage capacitor
injects a higher voltage to the test point when
SW2 is switched on. The lower current limiting
resistor increases the current charge onto the test
point.
Figure 32. ESD Test Waveform for IEC1000-4-2
t=0ns t=30ns
0A
15A
30A
t ➙
i ➙
Figure 31. ESD Test Circuit for IEC1000-4-2
Table 4. Transceiver ESD Tolerance Levels
Date: 6/2/04 SP3223EB/3243EB +3.0V to +5.5V RS-232 Transceivers © Copyright 2004 Sipex Corporation
20
D
ALTERNATE
END PINS
(BOTH ENDS)
D1 = 0.005" min.
(0.127 min.)
E
PACKAGE: PLASTIC
DUAL–IN–LINE
(NARROW)
A = 0.210" max.
(5.334 max).
E1
C
Ø
L
A2
A1 = 0.015" min.
(0.381min.)
B
B1
e = 0.100 BSC
(2.540 BSC)
e
A
= 0.300 BSC
(7.620 BSC)
DIMENSIONS (Inches)
Minimum/Maximum
(mm)
A2
B
B1
C
D
E
E1
L
Ø
16–PIN
0.115/0.195
(2.921/4.953)
0.014/0.022
(0.356/0.559)
0.045/0.070
(1.143/1.778)
0.008/0.014
(0.203/0.356)
0.780/0.800
(19.812/20.320)
0.300/0.325
(7.620/8.255)
0.240/0.280
(6.096/7.112)
0.115/0.150
(2.921/3.810)
0°/ 15°
(0°/15°)
20–PIN
0.115/0.195
(2.921/4.953)
0.014/0.022
(0.356/0.559)
0.045/0.070
(1.143/1.778)
0.008/0.014
(0.203/0.356)
0.980/1.060
(24.892/26.924)
0.300/0.325
(7.620/8.255)
0.240/0.280
(6.096/7.112)
0.115/0.150
(2.921/3.810)
0°/ 15°
(0°/15°)
28–PIN
0.115/0.195
(2.921/4.953)
0.014/0.022
(0.356/0.559)
0.045/0.070
(1.143/1.778)
0.008/0.014
(0.203/0.356)
1.385/1.454
(35.17/36.90)
0.300/0.325
(7.620/8.255)
0.240/0.280
(6.096/7.112)
0.115/0.150
(2.921/3.810)
0°/ 15°
(0°/15°)
21
Date: 6/2/04 SP3223EB/3243EB +3.0V to +5.5V RS-232 Transceivers © Copyright 2004 Sipex Corporation
D
EH
PACKAGE: PLASTIC SHRINK
SMALL OUTLINE
(SSOP)
DIMENSIONS (Inches)
Minimum/Maximum
(mm)
20–PIN
A
A1
Ø
L
Be
A
A1
B
D
E
e
H
L
Ø
0.068/0.078
(1.73/1.99)
0.002/0.008
(0.05/0.21)
0.010/0.015
(0.25/0.38)
0.278/0.289
(7.07/7.33)
0.205/0.212
(5.20/5.38)
0.0256 BSC
(0.65 BSC)
0.301/0.311
(7.65/7.90)
0.022/0.037
(0.55/0.95)
0°/8°
(0°/8°)
24–PIN
0.068/0.078
(1.73/1.99)
0.002/0.008
(0.05/0.21)
0.010/0.015
(0.25/0.38)
0.317/0.328
(8.07/8.33)
0.205/0.212
(5.20/5.38)
0.0256 BSC
(0.65 BSC)
0.301/0.311
(7.65/7.90)
0.022/0.037
(0.55/0.95)
0°/8°
(0°/8°)
28–PIN
0.068/0.078
(1.73/1.99)
0.002/0.008
(0.05/0.21)
0.010/0.015
(0.25/0.38)
0.397/0.407
(10.07/10.33)
0.205/0.212
(5.20/5.38)
0.0256 BSC
(0.65 BSC)
0.301/0.311
(7.65/7.90)
0.022/0.037
(0.55/0.95)
0°/8°
(0°/8°)
16–PIN
0.068/0.078
(1.73/1.99)
0.002/0.008
(0.05/0.21)
0.010/0.015
(0.25/0.38)
0.239/0.249
(6.07/6.33)
0.205/0.212
(5.20/5.38)
0.0256 BSC
(0.65 BSC)
0.301/0.311
(7.65/7.90)
0.022/0.037
(0.55/0.95)
0°/8°
(0°/8°)
Date: 6/2/04 SP3223EB/3243EB +3.0V to +5.5V RS-232 Transceivers © Copyright 2004 Sipex Corporation
22
D
EH
PACKAGE: PLASTIC
SMALL OUTLINE (SOIC)
(WIDE)
A
A1
Ø
L
Be
DIMENSIONS (Inches)
Minimum/Maximum
(mm)
A
A1
B
D
E
e
H
L
Ø
28–PIN
0.090/0.104
(2.29/2.649)
0.004/0.012
(0.102/0.300)
0.013/0.020
(0.330/0.508)
0.697/0.713
(17.70/18.09)
0.291/0.299
(7.402/7.600)
0.050 BSC
(1.270 BSC)
0.394/0.419
(10.00/10.64)
0.016/0.050
(0.406/1.270)
0°/8°
(0°/8°)
23
Date: 6/2/04 SP3223EB/3243EB +3.0V to +5.5V RS-232 Transceivers © Copyright 2004 Sipex Corporation
Gage
Plane
1.0 OIA
e
0.169 (4.30)
0.177 (4.50)
0.252 BSC (6.4 BSC)
0’-8’ 12’REF
0.039 (1.0)
e/2
0.039 (1.0)
0.126 BSC (3.2 BSC)
D
0.007 (0.19)
0.012 (0.30)
0.033 (0.85)
0.037 (0.95)
0.002 (0.05)
0.006 (0.15)
0.043 (1.10) Max
(θ3)
1.0 REF
0.020 (0.50)
0.026 (0.75)
(θ1)
0.004 (0.09) Min
0.004 (0.09) Min
0.010 (0.25)
(θ2)
0.008 (0.20)
DIMENSIONS
in inches (mm) Minimum/Maximum
Symbol 20 Lead 28 Lead
D 0.252/0.260 0.378/0.386
(6.40/6.60) (9.60/9.80)
e 0.026 BSC 0.026 BSC
(0.65 BSC) (0.65 BSC)
PACKAGE: PLASTIC THIN
SMALL OUTLINE
(TSSOP)
Date: 6/2/04 SP3223EB/3243EB +3.0V to +5.5V RS-232 Transceivers © Copyright 2004 Sipex Corporation
24
D2
NX K
NX L
E2
NX K
NX b
0.80 0.90 1.00
0 0.02 0.05
Dimensions in
(mm)
32 PIN QFN
JEDECMO220
(VHHD-4)
0 0.65 1.00
0.20 REF
0.35 0.40 0.45
A
A1
A2
A3
D
E
D2
L
MIN NOM MAX
3.50 3.65 3.80
E2 3.50 3.65 3.80
ND
5.00 BSC
5.00 BSC
8
NE 8
32 PIN QFN
e0.50 BSC
b 0.18 0.25 0.30
Ø
0º - 14º
N32
e
D
E
SEATING PLANE
A1
A
4X
Ø
º
A3
A2
K0.20 - -
PACKAGE: 32 PIN QFN
25
Date: 6/2/04 SP3223EB/3243EB +3.0V to +5.5V RS-232 Transceivers © Copyright 2004 Sipex Corporation
Part Number Temperature Range Package Types
SP3223EBCP .................................................... 0°C to +70°C -------------------------------------------- 20-pin PDIP
SP3223EBCA .................................................... 0°C to +70°C ------------------------------------------- 20-pin SSOP
SP3223EBCA/TR .............................................. 0°C to +70°C ------------------------------------------- 20-pin SSOP
SP3223EBCY .................................................... 0°C to +70°C ----------------------------------------- 20-pin TSSOP
SP3223EBCY/TR .............................................. 0°C to +70°C ----------------------------------------- 20-pin TSSOP
SP3223EBEP .................................................. -40°C to +85°C ------------------------------------------- 20-pin PDIP
SP3223EBEA .................................................. -40°C to +85°C ------------------------------------------ 20-pin SSOP
SP3223EBEA/TR ............................................ -40°C to +85°C ------------------------------------------ 20-pin SSOP
SP3223EBEY .................................................. -40°C to +85°C ---------------------------------------- 20-pin TSSOP
SP3223EBEY/TR ............................................ -40°C to +85°C ---------------------------------------- 20-pin TSSOP
SP3243EBCT .................................................... 0°C to +70°C ----------------------------------------- 28-pin WSOIC
SP3243EBCT/TR .............................................. 0°C to +70°C ----------------------------------------- 28-pin WSOIC
SP3243EBCA .................................................... 0°C to +70°C ------------------------------------------- 28-pin SSOP
SP3243EBCA/TR .............................................. 0°C to +70°C ------------------------------------------- 28-pin SSOP
SP3243EBCY ................................................... -0°C to +70°C ----------------------------------------- 28-pin TSSOP
SP3243EBCY/TR ............................................. -0°C to +70°C ----------------------------------------- 28-pin TSSOP
SP3243EBCR ................................................... -0°C to +70°C --------------------------------------------- 32-pin QFN
SP3243EBCR/TR ............................................. -0°C to +70°C --------------------------------------------- 32-pin QFN
SP3243EBET .................................................. -40°C to +85°C ---------------------------------------- 28-pin WSOIC
SP3243EBET/TR ............................................ -40°C to +85°C ---------------------------------------- 28-pin WSOIC
SP3243EBEA .................................................. -40°C to +85°C ------------------------------------------ 28-pin SSOP
SP3243EBEA/TR ............................................ -40°C to +85°C ------------------------------------------ 28-pin SSOP
SP3243EBEY .................................................. -40°C to +85°C ---------------------------------------- 28-pin TSSOP
SP3243EBEY/TR ............................................ -40°C to +85°C ---------------------------------------- 28-pin TSSOP
SP3243EBER .................................................. -40°C to +85°C -------------------------------------------- 32-pin QFN
SP3243EBER/TR ............................................ -40°C to +85°C -------------------------------------------- 32-pin QFN
Corporation
ANALOG EXCELLENCE
Sipex Corporation reserves the right to make changes to any products described herein. Sipex does not assume any liability arising out of the
application or use of any product or circuit described herein; neither does it convey any license under its patent rights nor the rights of others.
Sipex Corporation
Headquarters and
Sales Office
233 South Hillview Drive
Milpitas, CA 95035
TEL: (408) 934-7500
FAX: (408) 935-7600
Available in lead free packaging. To order add "-L" suffix to part number.
Example: SP3243EBCY/TR = standard; SP3243EBCY-L/TR = lead free
/TR = Tape and Reel
Pack quantity is 1,500 for SSOP, TSSOP and WSOIC. Pack quantity is 2,500 QFN
ORDERING INFORMATION
DATE REVISION DESCRIPTION
6/2/04 A Added QFN package.
REVISION HISTORY